CyberTAN Technology RV130W Wireless Multifunction VPN Router User Manual rv130 rv130w qsg en

CyberTAN Technology Inc. Wireless Multifunction VPN Router rv130 rv130w qsg en

Contents

User Manual.pdf

Quick Start GuideCisco Small BusinessRV130 Multifunction VPN Router RV130W Wireless Multifunction VPN RouterPackage Contents•Router•Ethernet Cable•Power Adapter•Quick Start Guide•Documentation and Software on CD-ROMVer sión en Esp añ ol par a M éxico e n e l CD Version en français sur CDVersione italiana sul CDDeutsch Version auf CD
2 Cisco Small Business RV130/RV130W Mutlifunction VPN Router WelcomeThank you for choosing the Cisco Small Business RV130/RV130W router. This guide describes how to physically install your Cisco RV130/RV130W and launch the web-based Device Manager.Mounting the Cisco RV130/RV130WPlacement TipsTo prevent the device from overheating or being damaged:• Ambient Temperature—Do not operate it in an area that exceeds an ambient temperature of 104°F (40°C).•Air Flow—Be sure that there is adequate air flow around the device.• Mechanical Loading—Be sure that the device is level and stable to avoid any hazardous conditions.Place the device on a flat surface so that it sits on the four rubber feet.Wall MountingThe router has two wall-mount slots on the bottom panel. To mount the router on a wall, you need mounting hardware (not included). Suggested wood screw size is illustrated here (not true to scale).16.50 - 6.86 mm 16 mm3.0-3.5 mm370612
Cisco Small Business RV130/RV130W Mutlifunction VPN Router 3 Cisco RV130/RV130W FeaturesRV130 Front PanelPower Solid green when the device is powered on and booted. Flashes green when the device is booting or upgrading the firmware.Flashes rapidly if the device is running corrupt firmware.VPN (for site-to-site IPsec VPN only)Solid green when at least one VPN tunnel is active.Flashes green when receiving or transmitting data through a VPN tunnel.Amber when no enabled VPN tunnel is active. USB Solid green when the USB dongle is successfully connected to an Internet Service Provider (ISP) and an IP address has been assigned. Flashes green when the port is sending or receiving data.Amber when the USB dongle is recognized but failed to connect to an ISP.2
4 Cisco Small Business RV130/RV130W Mutlifunction VPN Router RV130W Front PanelWAN Solid green when the device is connected to the Internet using a wired connection. Off when the device is not connected to the Internet or is connected using a USB dongle.Flashes green when sending or receiving data over the wired connection.LAN (1-4) RJ-45 connectors that link local area network devices, such as PCs, print servers, or switches, to the device. The numbered lights correspond to the LAN ports on the back panel.Solid green when the corresponding port is connected to a device. Flashes green when the port is sending or receiving data.Power Solid green when the device is powered on and booted. Flashes green when the device is booting or upgrading the firmware.Flashes rapidly if the device is running corrupt firmware.VPN(for site-to-site IPsec VPN only)Solid green when at least one VPN tunnel is active. Flashes green when receiving or transmitting data through a VPN tunnel.Amber when no enabled VPN tunnel is active.USB Solid green when the USB dongle is successfully connected to an Internet Service Provider (ISP) and an IP address has been assigned. Flashes green when the port is sending or receiving data.Amber when the USB dongle is recognized but failed to connect to an ISP.
Cisco Small Business RV130/RV130W Mutlifunction VPN Router 5 WLAN Lit green when the wireless radio is enabled. Off when the wireless radio is switched off. Flashes green when transmitting or receiving data using a wireless connection. WAN Lit green when the device is connected to the Internet using a wired connection. The light is off when the device is not connected to the Internet or is connected using a USB dongle.Flashes green when sending or receiving data over the wired connectionLAN (1-4) RJ-45 connectors that link local area network devices, such as PCs, print servers, or switches, to the device. The numbered lights correspond to the LAN ports on the back panel.Lit green when the corresponding port is connected to a device. Flashes green when the port is sending or receiving data.
6 Cisco Small Business RV130/RV130W Mutlifunction VPN Router RV130/RV130W Back Panel RV130/RV130W Side Panel USB—Type A USB port on the right side of the housing that supports 3G/4G/LTE USB dongles. Kensington Lock Slot— Lock slot on the right side to secure the device physically, using Kensington lockdown equipment (not included).RESET The RESET button has two functions:•To reboot the unit and retain the current configuration, press and hold RESET for at least 3, but no more than 10 seconds, by using a paper clip or a pen tip. •To reboot the unit and restore the factory default configuration, press and hold the RESET button for more than 10 seconds. Changes you have made to the Cisco RV130/RV130W configuration are lost.LAN (1-4) RJ-45 device connections to link local area network devices, such as PCs, print servers, or switches, to the device.WAN Internet device connection for connecting the device to a wide area network device, such as a cable or DSL modem.POWER Switch that toggles power to the device on or off. 12VDC Power port that connects the device to the provided 12VDC power adapter.
Cisco Small Business RV130/RV130W Mutlifunction VPN Router 7 Connecting the EquipmentYou must connect a PC to the device by using an Ethernet cable to perform the initial configuration. After the initial configuration, administrative tasks can be performed through the network or by using a wireless connection. To connect a PC to the device for initial configuration:STEP 1Power off all equipment, including the cable or DSL modem, the PC, and the device.STEP 2Use an Ethernet cable to connect your cable or DSL modem to the WAN por t on your device.STEP 3Connect another Ethernet cable from one of the LAN (Ethernet) ports to the Ethernet port on the PC.STEP 4Power on the cable or DSL modem and wait until the connection is active.STEP 5Connect the power adapter to the device’s 12VDC port.CAUTION Use only the power adapter that is supplied with your device. Using a different power adapter could damage the device.The POWER button is on by default. The power light on the front panel is solid green when the power adapter is connected properly and the device has finished booting.STEP 6Plug the other end of the adapter into an electrical outlet. Use the plug (supplied) specific to your country.STEP 7Continue with the instructions in the Using the Setup Wizard to configure the device.3
8 Cisco Small Business RV130/RV130W Mutlifunction VPN Router Using the Setup WizardThe Setup Wizard and Device Manager are supported on Microsoft Internet Explorer 7.0 or later, Mozilla Firefox 3.5 or later, Apple Safari 3.0 or later, and Google Chrome 5.0 or later. To configure the device by using the Setup Wizard:STEP 1Power on the PC that you connected to the LAN1 port in Step 3 of the Connecting the Equipment section. Your PC becomes a DHCP client of the device and receives an IP address in the 192.168.1.xxx range. STEP 2Launch a web browser window on your PC. STEP 3In the address bar, enter the default IP address of the device 192.168.1.1. A site security certificate message appears. Cisco RV130/RV130W uses a self-signed security certificate. This message appears because the device is not known to your PC. STEP 4Click Continue to this website (or the option shown on your particular web browser) to continue. The login page appears.STEP 5Enter the username and password. The default username is cisco. The default password is cisco. Passwords are case sensitive. STEP 6Click Log In. The Router Setup Wizard is luanched.STEP 7Follow the on-screen instructions to set up your device. The Router Setup Wizard tries to automatically detect and configure your connection. If it is unable to do so, it might ask you for information about your Internet connection. Contact your ISP for this information.STEP 8Change the password as instructed by the Router Setup Wizard or follow the instructions in the Changing the Administrator Username and Password section. Log into the device with the new username and password. The Device Manager Getting Started page appears. It displays the most common configuration tasks. STEP 9Click one of the listed tasks or a task listed in the navigation bar to complete the configuration. STEP10 Save any additional configuration changes and log out of Device Manager.4
Cisco Small Business RV130/RV130W Mutlifunction VPN Router 9 Changing the Administrator Username and PasswordTo change the administrator username and password on the device:STEP 1From the Getting Started page, select Change Default Administrator Password or select Administration > Users. STEP 2Check Edit Admin Settings. STEP 3Enter a new username in Administrator Account Settings. We recommend that you do not use cisco.STEP 4Enter the old password.STEP 5Enter the new password. Passwords should not contain dictionary words from any language or be the default password. They should contain a mix of uppercase and lowercase letters, numbers, and symbols. Passwords must be at least 8 but no more than 30 characters in length.STEP 6Enter the new password again to confirm.STEP 7Click Save.
10 Cisco Small Business RV130/RV130W Mutlifunction VPN Router Where to Go From HereSupportCisco Small Business Support Communitywww.cisco.com/go/smallbizsupportCisco Small Business Support and Resourceswww.cisco.com/go/smallbizhelpPhone Support Contacts www.cisco.com/en/US/support/tsd_cisco_small_business _support_center_contacts.htmlCisco Small Business Firmware Downloadswww.cisco.com/cisco/software/navigator.html?i=!chSelect a link to download firmware for Cisco Small Business Products. No login is required.Product DocumentationCisco Small Business Routersswww.cisco.com/go/smallbizroutersCisco Small BusinessCisco Partner Central for Small Business (Partner Login Required)www.cisco.com/web/partners/sell/smbCisco Small Business Homewww.cisco.com/smb5
Cisco Small Business RV130/RV130W Mutlifunction VPN Router 11
Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAwww.cisco.comSmall Business Support, Global: www.cisco.com/go/sbscCisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliatesin the U.S. and other countries. To view a list of Ciscotrademarks, go to this URL:www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of theirrespective owners. The use of the word partner does not imply a partnership relationshipbetween Cisco and any other company. (1110R)© 2013 Cisco Systems, Inc. All rights reserved. 78-21400-01

Navigation menu