Coulisse ABC23 Curtain Motor User Manual CBB5C3F7CAE92E706466

Coulisse B.V. Curtain Motor CBB5C3F7CAE92E706466

User Manual

indoor use only!!1.3A1.3BUser manual Curtain MotorABC-23-W120WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.Do not make repairs yourself. Do not attempt to open the device or disassemble it. You run the risk of electric shock and voiding the limited warranty. No user-serviceable parts are inside.WARNING: 1. General informationThe ABC-23 is a curtain motor to motorize curtain tracks. The motor can be operated with a coulisse remote control or manually by pulling on the curtain. Limits and favorite position are set with the remote control.1.2.1. 2.Step 6: Exit the program-mode by pressing the program button againThen set the right endpositionUse the left and right buttons to go to the left endpositionSet the position by pressing the center + left buttonFirst set the left endpositionStep 5: Set endpositionsUse the left and right buttons to go to the right endpositionSet the position by pressing the center + right buttonAction confi rmed: curtain stops stepping for 3 secondsAction confi rmed: curtain stops stepping for 3 secondsExit program mode: Shortly press program button1.3 Connectors and buttonsProgram buttonIMPORTANT:When the mains cable is permanently connected, a readily accessible disconnect device shall be incorporated external to the motor.When there is a pluggable connecter installed on the mains cable, the socket-outlet shall be installed near the motor and shall be easily accessible. Mains cable 230V 120VNeutral Blue WhitePhase Brown BlackGround Yellow-green Green2. Programming and operating(also possible by using ‘SingleSelect’, see manual remote control*)2.1 First useStep 1: Connect the motor with the powersupplyStep 2: Set the curtain in program-mode by pushing the program buttonStep 3: Pair the curtain to a channel/remoteChoose channel by pressing the ChannelSelect buttonPair/unpair by pressing the program button on the backside of the remotePress the left + right to change the rotation directionStep 4: Switch the rotating directionSet to program mode:Shortly press program button Program mode:Curtain is stepping...Action confi rmed: curtain stops stepping for 3 secondsAction confi rmed: curtain stops stepping for 3 secondsIf you press left and the curtain goes right, the rotation direction of the curtain has to be switched. *Manuals are also available on our website www.coulisse.com2202501570521.1 General dimensions Type Power Supply Rated Power Torq-Speed Curtain weightABC-23-W 230V AC 50Hz 0.23A - 45W 0,8Nm, 20 cm/s 50kgABC-23-W120 120V AC 60Hz 0.46A - 45W 0,8Nm, 24 cm/s 50kg1.2 Performances Type Max operating timeOperating temp. Max. channels to pairDeg. of protectionABC-23-W & W(120) 4 min. 5 - 60° 32 channels IP20Coulisse B.V., Vonderweg 48, 7468 DC Enter, The NetherlandsABC-23-U_R0_Do not make repairs yourself. Do not attempt to open the device or disassemble it. You run the risk of electric shock and voiding the limited warranty. No user-serviceable parts are inside.WARNING: - Do not let children play with the curtain and/or remote control.- Only use powersupplies or batteries that comply with the specifi cations on the motor.- In case of malfunction, unplug the device or remove the batteries and contact your dealer.- Take care that the curtain can move freely and is not blocked by objects.- Take care that the powersupply cable is out of reach for children.- Do not paint the device.- Keep the device dry.5. Service & Support4.2 CleaningFollow these general rules when cleaning the outside of the device and its components:- Make sure the device is unplugged.- Use a damp, soft, lint-free cloth. Avoid getting moisture in openings.- Don’t use aerosol sprays, solvents, alcohol, or abrasives.Do not make repairs yourself. Do not attempt to open the device or disassemble it. You run the risk of electric shock and voiding the limited warranty. No user-serviceable parts are inside.WARNING: Online ResourcesFor the latest information and updated manuals go to www.coulisse.com.Obtaining Warranty ServiceFirst follow the advice in this booklet and then go to your local dealer. If the product appears to be damaged or does not function properly, go to your local dealer for instructions on how to obtain warranty service.3. Tips & TroubleshootingPlease check www.coulisse.com for the latest tips and troubleshooting guide.4. Safety & Cleaning4.1 SafetyGB0Shortly press program buttonProgram mode:is stepping...- Reset to factory defaults & Erase all paired channels/remotesHold program button untill curtain stops stepping for the second time (ca. 10 sec.)10 sec2.2 Operating- Control by remote (see manual remote control)2.4 ResetShortly press program buttonProgram mode:is stepping...- Reset to factory defaultsHold program button untill curtain stops stepping and steps once (ca. 15 sec.)15 sec Additional curtain settings: Available Switch rotation direction YesFavorite position YesDomotica Box Yes2.5 Additional curtain settingsWe refer to the manual of the Coulisse Remote control to set the additional curtain settings.- Manual Control (by pulling)From factory default ‘Direct take over’ is activated. A motor will take over the command directly and runs to it’s endlimit. Switch this function off when it is recommended that the motor must move in small steps.2.3 Direct take overPull curtain to start the motorCurtain moves to end limit- Manual Control (by button)Shortly press program buttonProgram mode: Blind is stepping...Hold program button untill blind stops stepping (5 sec. )5 secHold program button for more than 2 sec. Curtain moves as long as button is pressed (max. 15 sec.)For moving in opposite direction release button and hold program button again for more than 2 sec.Disclaimer:© Copyright CoulisseAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, by any means, electronic, mechanical, photocopying, recording, digital or otherwise without the written permission of the publisher.Although this manual has been composed with the most care, Coulisse B.V. does not accept any responsibility for damage due to mistakes and/or faults in this manual.Coulisse B.V. reserves the right to revise the manual and to revise and/or changes its content at any time, without obligation to notify any person or entity of such revisions or changes.The most recent version replaces older versions of this manual. The most recent version is available at ww.coulisse.com or contact your Coulisse contact person.We invite you to send remarks and comments about this manual to Coulisse at manuals@coulisse.com.1.2A-
1AW53422226062CR-02 CR-122.1A= 2 x= 4 x2ACR-06-WCR-07/08-WCR-01-WCR-02CR-04-WCR-05-WCR-13-WABC-23CR-09/10 CR-11-WCR-12CR-032.1CCR-01CR-02= 1 x= 2 x2.1B2.2ACR-042.2B2.2CCR-11122.2E2.2F2.2G2.2DCR-09 CR-10or123CR-10CR-09 CR-09 CR-094ABC-23-A_R0_CR-14-WAssembly ManualAbsolute ControlCurtain Motor ABC-23-W120Rail lenght (CR-01-W) = Width - 150mmBelt length (CR-02) = 2 x Width - 50mmNumber of runners (CR-11-W) = +/- 8pcs/mtrCeiling brackets = (CR06-W) = 1pc/mtr1. Calculations2. AssemblyGB02.1 Assembling Belt2.2 Assembling Endcaps
2.4A2.4B2.4C21CR-06-WCR-07-WCR-08-WCR-14===2.2H2.2JABC-23ABC-232.3A2.3BCR-05-W2CR-0912.2I12ABC-23-A_R0_GB02.4 Installation bracket2.3 Assemble motor
NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that maycause undesired operation.Changes or modifications made to this equipment not expressly approved by ShapeTechnology (Shenzhen) Co., Ltd may void the FCC authorization to operate this equipment.This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the followingmeasures:is connected.!

Navigation menu