Corrisoft 1023018 User Manual

Corrisoft

User Manual

Page 1 of 4 Rev. 1.01 5/21/99 wcOperating manual for Wireless Cuff .docOperation manual for the 1023018 wireless transmitterWireless Cuff Preparation:The wireless cuff includes five components, a battery assembly (hub), “O” ring, transmitterassembly, a bracelet and four screws. (See figure 1)• Battery Assembly - Provides a nominal 6 Volt DC source to power the transmitter whenassembled. Life is estimated at 3 months average. The transmitter will cease operation ataround 3.9 Volts.• “O” Ring - Seals the transmitter compartment when assembled making it waterproof.• Transmitter Assembly - Encapsulated transmitter with battery contacts for power.Periodically sends a message to the receiver which is resident in the PTU.• Screws, 4 each - #4 Phillips, flat head, stainless steel, sheet metal screws; 3/8” in length.A cuff may be attached to a client once preparation has been completed. Select an appropriatelength bracelet for the ankle (table 1), one battery assembly with “O” ring installed, onetransmitter assembly and four screws. Sizes 5,6,7 and 8 are stocked by ABS. Other sizes will haveto be special ordered at the time of contract. Lead time is two weeks. # of holes AnkleCircumference # of Holes AnkleCircumference 2 6.5” 7 9.0” 3 7.0” 8 9.5” 4 7.5” 9 10.0” 5 8.0” 10 10.5” 6 8.5” 11 11.0” Table 1Assemble Transmitter and Battery:Align the battery assembly key appropriately with the transmitter assembly slot and lightly engagethe hub of the battery assembly to the transmitter cavity. Rotate one assembly carefully until theindex mark on one aligns with the index mark on the other. Press the two assemblies togetherfirmly with both hands until little gap can be observed between the two assemblies. Hold them inplace with one hand and insert one screw (using a Phillips screwdriver) at a time. Insert thesecond screw 180 degrees from the first and tighten. The other two screws may be inserted in anyorder.Wireless Bracelet Installation:Figure 2 provides the necessary client installation instructions. Install the bracelet to one side ofthe cuff assembly first. The second side is installed while against the clients wrist or ankle. Oncethe cuff is installed on the client it must be activated. Activation occurs when the magnet providedis placed against the transmitter body for a minimum of five seconds. Once activated the client isfree to move within the limits of the following violation definitions.
Page 2 of 4 Rev. 1.01 5/21/99 wcOperating manual for Wireless Cuff .doc• Proximity - Occurs when the client, wearing the cuff, moves away from the PTU between20 ft. outdoors or 30 ft indoors. To be detected as a cuff violation the client must outsidethese limits for a minimum of for 30 minutes. This violation rearms itself if an individualmoves back inside these limits after being out for 30 minutes.• Cuff violation - Occurs when a client forcibly removes or cuts the bracelet from thetransmitter. This violation will not page again until the bracelet has been replaced and the cuffhas been rearmed (minimum of 10 seconds) with the rearming tool. Cautions• After rearming is complete the client must stay within the proximity limits for 5minutes. Premature movement outside these limits may prevent a cuff violation frombeing detected.• Metal obstructions, in the line of sight between the cuff and the PTU, such as metalfiling cabinets, walls or refrigerators can result in false proximity violations.Figure 1TransmitterBattery“O” ringScrews usedto attachedbattery totransmitterFCC identifierlocation.
Page 3 of 4 Rev. 1.01 5/21/99 wcOperating manual for Wireless Cuff .docALIGNMENTPINGROOVEINDEX TABINDEX TABALIGNMENTPINTITLE Figure 2 - Wireless cuff1. Install O-Ring over battery hub.2. Align the index tabs and press to mate the two sections. DO NOT TWIST toalign the index tabs. If the tabs are not aligned, pull the sections apart and re-seat. Sections WILL NOT MATE if the alignment pin is not seated in thealignment pin groove.3. Using a #1 phillips screwdriver, install the four screws.4. Install the cuff strap. Make sure the metal tab on the cuff strap will contactthe metal contact in the transmitter assembly and push the cuff tab into a recessof the transmitter assembly. Loop the strap around the arm or leg, holding thetransmitter assembly with the screws (battery section) against the arm or leg,and snap the other end of the cuff strap into place.O-RINGSCREW 4 EASTRAPASSYBATTERYTRANSMITTERBATTERY HUB
Page 4 of 4 Rev. 1.01 5/21/99 wcOperating manual for Wireless Cuff .docFCC Label ExhibitThe transmitter is too small to place the label on it. The FCC ID number will be stamped into the plasticcase. See figure one for location of stamping. There will be no serial number stamped into the case.This device complies with Part 15 of the FCC rules. Operation is subject to the followingtwo conditions: (1) this device may not cause harmful interference, and (2) this devicemust accept any interference received, including interference that may cause undesiredoperationABS<Comtrak Model Numbers: 1023018 Serial No.: _ _ _FCC ID: OAM1023018Advanced Business Sciences Made in USA

Navigation menu