Corning Optical Communication MA850C In Building RF Distribution System User Manual Revised

Corning Optical Communication Wireless In Building RF Distribution System Users Manual Revised

Users Manual Revised

P/N: 709C001103 REV: A00 Date: 06-NOV-06 MMMooobbbiiillleeeAAAcccccceeessssss 888555000 (((fffooorrr FFFCCCCCC))) Installation and Configuration Guide
Preface Preface Material MA 850 Installation and Configuration Guide II MobileAccess Ltd. Vienna, Virginia Tel: +1-703-848-0200 http://www.MobileAccess.com
Preface Preface Material MA 850 Installation and Configuration Guide III PPrreeffaaccee MMaatteerriiaall © COPYRIGHT 2006, MOBILEACCESS NETWORKS INC. ALL RIGHTS RESERVED. MOBILEACCESSTM IS A REGISTERED TRADEMARK OF MOBILEACCESS. THIS DOCUMENT CONTAINS OTHER TRADEMARKS, TRADE NAMES AND SERVICE MARKS OF MOBILEACCESS AND OTHER ORGANIZATIONS, ALL OF WHICH ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS. THIS DOCUMENT CONTAINS CONFIDENTIAL AND PROPRIETARY INFORMATION OF MOBILEACCESS AND MAY NOT BE COPIED, TRANSMITTED, STORED IN A RETRIEVAL SYSTEM OR REPRODUCED IN ANY FORMAT OR MEDIA, IN WHOLE OR IN PART, WITHOUT THE PRIOR WRITTEN CONSENT OF MOBILEACCESS. INFORMATION CONTAINED IN THIS DOCUMENT SUPERSEDES ANY PREVIOUS MANUALS, GUIDES, SPECIFICATIONS, DATA SHEETS OR OTHER INFORMATION THAT MAY HAVE BEEN PROVIDED OR MADE AVAILABLE TO THE USER. THIS DOCUMENT IS PROVIDED FOR INFORMATIONAL PURPOSES ONLY, AND MOBILEACCESS DOES NOT WARRANT OR GUARANTEE THE ACCURACY, ADEQUACY, QUALITY, VALIDITY, COMPLETENESS OR SUITABILITY FOR ANY PURPOSE OF THE INFORMATION CONTAINED IN THIS DOCUMENT. MOBILEACCESS RESERVES THE RIGHT TO MAKE UPDATES, IMPROVEMENTS AND ENHANCEMENTS TO THIS DOCUMENT AND THE PRODUCTS TO WHICH IT RELATES AT ANY TIME WITHOUT PRIOR NOTICE TO THE USER. MOBILEACCESS MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THIS DOCUMENT OR ANY INFORMATION CONTAINED HEREIN.
Preface Preface Material MA 850 Installation and Configuration Guide IV Policy for Warrantee and Repair MOBILEACCESS TESTS AND INSPECTS ALL ITS PRODUCTS TO VERIFY THEIR QUALITY AND RELIABILITY. MOBILEACCESS USES EVERY REASONABLE PRECAUTION TO ENSURE THAT EACH UNIT MEETS THEIR DECLARED SPECIFICATIONS BEFORE SHIPMENT. CUSTOMERS SHOULD ADVISE THEIR INCOMING INSPECTION, ASSEMBLY, AND TEST PERSONNEL ABOUT THE PRECAUTIONS REQUIRED IN HANDLING AND TESTING OUR PRODUCTS. MANY OF THESE PRECAUTIONS CAN BE FOUND IN THIS MANUAL. THE PRODUCTS ARE COVERED BY THE FOLLOWING WARRANTIES: General Warranty MOBILEACCESS WARRANTS TO THE ORIGINAL PURCHASER ALL STANDARD PRODUCTS SOLD BY MOBILEACCESS TO BE FREE OF DEFECTS IN MATERIAL AND WORKMANSHIP FOR ONE (1) YEAR FROM DATE OF SHIPMENT FROM MOBILEACCESS. DURING THE WARRANTY PERIOD, MOBILEACCESS WILL REPAIR OR REPLACE ANY PRODUCT THAT MOBILEACCESS PROVES TO BE DEFECTIVE. THIS WARRANTY DOES NOT APPLY TO ANY PRODUCT THAT HAS BEEN SUBJECT TO ALTERATION, ABUSE, IMPROPER INSTALLATION OR APPLICATION, ACCIDENT, ELECTRICAL OR ENVIRONMENTAL OVER-STRESS, NEGLIGENCE IN USE, STORAGE, TRANSPORTATION OR HANDLING. Specific Product Warranty Instructions ALL MOBILEACCESS PRODUCTS ARE WARRANTED AGAINST DEFECTS IN WORKMANSHIP, MATERIALS AND CONSTRUCTION, AND TO NO FURTHER EXTENT. ANY CLAIM FOR REPAIR OR REPLACEMENT OF UNITS FOUND TO BE DEFECTIVE ON INCOMING INSPECTION BY A CUSTOMER MUST BE MADE WITHIN 30 DAYS OF RECEIPT OF SHIPMENT, OR WITHIN 30 DAYS OF DISCOVERY OF A DEFECT WITHIN THE WARRANTY PERIOD. THIS WARRANTY IS THE ONLY WARRANTY MADE BY MOBILEACCESS AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. MOBILEACCESS SALES AGENTS OR REPRESENTATIVES ARE NOT AUTHORIZED TO MAKE COMMITMENTS ON WARRANTY RETURNS. Returns IN THE EVENT THAT IT IS NECESSARY TO RETURN ANY PRODUCT AGAINST ABOVE WARRANTY, THE FOLLOWING PROCEDURE SHALL BE FOLLOWED: 1. RETURN AUTHORIZATION IS TO BE RECEIVED FROM MOBILEACCESS PRIOR TO RETURNING ANY UNIT. ADVISE MOBILEACCESS OF THE MODEL, SERIAL NUMBER, AND DISCREPANCY. THE UNIT MAY THEN BE FORWARDED TO MOBILEACCESS, TRANSPORTATION PREPAID. DEVICES RETURNED COLLECT OR WITHOUT AUTHORIZATION MAY NOT BE ACCEPTED. 2. PRIOR TO REPAIR, MOBILEACCESS WILL ADVISE THE CUSTOMER OF OUR TEST RESULTS AND ANY CHARGES FOR REPAIRING CUSTOMER-CAUSED PROBLEMS OR OUT-OF-WARRANTY CONDITIONS ETC. 3. REPAIRED PRODUCTS ARE WARRANTED FOR THE BALANCE OF THE ORIGINAL WARRANTY PERIOD, OR AT LEAST 90 DAYS FROM DATE OF SHIPMENT. Limitations of Liabilities MOBILEACCESS'S LIABILITY ON ANY CLAIM, OF ANY KIND, INCLUDING NEGLIGENCE FOR ANY LOSS OR DAMAGE ARISING FROM, CONNECTED WITH, OR RESULTING FROM THE PURCHASE ORDER, CONTRACT, QUOTATION, OR FROM THE PERFORMANCE OR BREACH THEREOF, OR FROM THE DESIGN, MANUFACTURE, SALE, DELIVERY, INSTALLATION, INSPECTION, OPERATION OR USE OF ANY EQUIPMENT COVERED BY OR FURNISHED UNDER THIS CONTACT, SHALL IN NO CASE EXCEED THE PURCHASE PRICE OF THE DEVICE WHICH GIVES RISE TO THE CLAIM. EXCEPT AS EXPRESSLY PROVIDED HEREIN, MOBILEACCESS MAKES NO WARRANTY, EXPRESSED OR IMPLIED, WITH RESPECT TO ANY GOODS, PARTS AND SERVICES PROVIDED IN CONNECTION WITH THIS AGREEMENT INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. MOBILEACCESS SHALL NOT BE LIABLE FOR ANY OTHER DAMAGE INCLUDING, BUT NOT LIMITED TO, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH FURNISHING OF GOODS, PARTS AND SERVICE HEREUNDER, OR THE PERFORMANCE, USE OF, OR INABILITY TO USE THE GOODS, PARTS AND SERVICE.
Preface Preface Material MA 850 Installation and Configuration Guide V Reporting Defects THE UNITS WERE INSPECTED BEFORE SHIPMENT AND FOUND TO BE FREE OF MECHANICAL AND ELECTRICAL DEFECTS. EXAMINE THE UNITS FOR ANY DAMAGE THAT MAY HAVE BEEN CAUSED IN TRANSIT. IF DAMAGE IS DISCOVERED, FILE A CLAIM WITH THE FREIGHT CARRIER IMMEDIATELY. NOTIFY MOBILEACCESS AS SOON AS POSSIBLE. NOTE: KEEP ALL PACKING MATERIAL UNTIL YOU HAVE COMPLETED THE INSPECTION WARNING: TO COMPLY WITH FCC RF EXPOSURE COMPLIANCE REQUIREMENTS, ANTENNAS USED FOR THIS PRODUCT MUST BE FIXED MOUNTED ON INDOOR PERMANENT STRUCTURES, PROVIDING A SEPARATION DISTANCE OF AT LEAST 20 CM FROM ALL PERSONS DURING NORMAL OPERATION. WARNING: ANTENNA GAIN SHOULD NOT EXCEED 10 dBi. WARNING: EACH INDIVIDUAL ANTENNA USED FOR THIS TRANSMITTER MUST BE INSTALLED TO PROVIDE A MINIMUM SEPARATION DISTANCE OF 20 CM OR MORE FROM ALL PERSONS AND MUST NOT BE CO-LOCATED WITH ANY OTHER ANTENNA FOR MEETING RF EXPOSURE REQUIREMENTS. WARNING: THE DESIGN OF THE ANTENNA INSTALLATION NEEDS TO BE IMPLEMENTED IN SUCH A WAY SO AS TO ENSURE RF RADIATION SAFETY LEVELS AND NON-ENVIRONMENTAL POLLUTION DURING OPERATION. ATTENTION: COMPLIANCE WITH RF SAFETY REQUIREMENTS: MOBILEACCESS™ PRODUCTS HAVE NO INHERENT SIGNIFICANT RF RADIATION. THE RF LEVEL ON THE DOWN LINK IS VERY LOW AT THE DOWNLINK PORTS. THEREFORE, THERE IS NO DANGEROUS RF RADIATION WHEN THE ANTENNA IS NOT CONNECTED. Safety WARNING! To comply with FCC RF exposure compliance requirements, antennas used for this product must be fixed mounted on indoor permanent structures, providing a separation distance of at least 20 cm from all persons during normal operation. 1. Each individual antenna used for this transmitter must be installed to provide a minimum separation distance of 20 cm or more from all persons and must not be co-located with any other antenna for meeting RF exposure requirements. 2. The design of the antenna installation needs to be implemented in such a way so as to ensure RF radiation safety levels and non-environmental pollution during operation. Compliance with RF safety requirements: • MobileAccess™ products have no inherent significant RF radiation. • The RF level on the downlink is very low at the downlink ports. Therefore, there is no dangerous RF radiation when the antenna is not connected.
Preface Preface Material MA 850 Installation and Configuration Guide VI Certification MobileAccess products have met the approvals of the following certifying organizations: ISO 9001:2000 (from March 15, 2004) FCC Certification For US: FCC 47 CFT part 15 for 802.11b/g Per section 15.204B. ID:OJFMA850 will only be supplied as complete system per section 15.204(b) of rules. FCC certification for MA 850 is valid for use only with the following elements: Antenna types: section 2.4.1 in this User Guide AP Types: section 2.5 in the User Guide NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. WARNING! Changes or modifications to this equipment not expressly approved by the party responsible for compliance MobileAccess Ltd. could void the user’s authority to operate the equipment.
Preface Preface Material MA 850 Installation and Configuration Guide VII Professional Installation of Transmitter According to FCC 15.203, if an intentional radiator has a standard antenna connector, it must be professionally installed according to FCC 15.203 regulations: 1. The MA850 cannot be sold to the general public. Only professional installer, qualified ("licensed") by MobileAccess for this purpose is aloud to install the MA850. 2. The installation must be controlled and follow the requirement of "Installation Manual" (P/N:709C001103). Each potential installer must receive special training, which is a condition for receiving the license from MobileAccess Inc to become a "licensed" installer. The installation procedure as described in the "Installation Manual" includes the mechanical installation and initial setup by a PC based tool. 3. The intended application of the system is exclusively for the commercial/industry use.
Preface Preface Material MA 850 Installation and Configuration Guide VIII About This Guide This user guide provides all the information necessary to install and configure the MobileAccess MA 850. Revision History The revision history for this document is shown in Table 1-1. Table 1-1: Revision history P/N and REV Date Description
Preface Preface Material MA 850 Installation and Configuration Guide IX List of Acronyms AGC Automatic Gain Control BDA Bi-Directional Amplifier BU Base Unit DL Downlink RHU Remote Hub Unit SNR Signal to Noise Ratio UL Uplink VDC Volts Direct Current AP Access Point
Preface Preface Material MA 850 Installation and Configuration Guide X Table of Contents Preface Material .......................................................................................................................III Policy for Warrantee and Repair......................................................................................................... IV Certification ...................................................................................................................................... VI Professional Installation of Transmitter..............................................................................................VII About This Guide ............................................................................................................................VIII Revision History ..............................................................................................................................VIII List of Acronyms ............................................................................................................................... IX Table of Contents................................................................................................................................X Introduction to the MA 850 System ........................................................................................1 1.1 About MobileAccess MA 850 .........................................................................................................1 1.1.1 MA 850 Features and Capabilities ........................................................................................2 1.2 MA 850 Front and Rear Panels......................................................................................................3 1.2.1 Front Panel Connections and LEDs.......................................................................................3 1.2.2 Rear Panel Port Connections and LEDs ................................................................................4 1.3 Unit Architecture..........................................................................................................................5 1.4 Installation Configurations ............................................................................................................5 1.4.1 Standalone.........................................................................................................................6 1.4.2 Add-On to MA 1000 RHU ....................................................................................................6 1.4.3 Add-on to MA 2000 System.................................................................................................7 1.5 Signal Distribution in the MA 850 ..................................................................................................8 1.6 Commissioning and Monitoring .....................................................................................................8 Infrastructure Preparation.......................................................................................................9 2.1 Installation Requirements.............................................................................................................9 2.2 Coaxial Cable Connections ..........................................................................................................10 2.2.1 General Cable Installation Procedures ................................................................................10 2.2.2 RF Rules ..........................................................................................................................10 2.3 Power Consumption, Connections and Power Supplies .................................................................11 2.3.1 Power Safety Instructions .................................................................................................11 2.3.2 MA 850 Power Consumption..............................................................................................11 2.3.3 Types of Power Supplies ...................................................................................................11
Preface Preface Material MA 850 Installation and Configuration Guide XI 2.3.4 Power Connections ...........................................................................................................11 2.4 In-building Antennas..................................................................................................................12 2.4.1 Antenna Types .................................................................................................................12 2.4.2 Antenna Connections ........................................................................................................12 2.5 Access Points.............................................................................................................................13 Installation..............................................................................................................................14 3.1 Accessory Kits............................................................................................................................14 3.2 Placing the Unit and Recording Location......................................................................................15 3.3 Standalone Wall Mount Installation .............................................................................................15 3.4 Add-on to an MA 1000 System Installation ..................................................................................16 3.5 Add-on to an MA 1000 with MA 1200 ..........................................................................................19 3.6 Add-on to an MA 2000 System....................................................................................................22 3.6.1 MA 850 RC 2000 Assembly................................................................................................22 3.6.2 MA 850 Rack Mount..........................................................................................................24 3.6.3 MA 850 Wall Mount Installation .........................................................................................24 Configuration and Management............................................................................................25 4.1 Local Configuration and Monitoring .............................................................................................26 4.1.1 Getting Started.................................................................................................................26 4.1.2 MA 850 Customer Tool Window Description .......................................................................27 4.1.3 Configuration Using MA 850 Customer Tool........................................................................28 4.1.4 Monitoring Using MA 850 Customer Tool............................................................................28 4.2 Remote - Web Browser Session ..................................................................................................29 4.2.1 IP Configuration Procedure ...............................................................................................30 4.2.1.1 Connecting to the Network ...................................................................................30 4.2.1.2 Performing Auto-Discovery....................................................................................30 4.2.1.3 Assigning a Static IP Address ................................................................................31 4.2.1.4 Configuring the SNMP Parameters .........................................................................34 4.2.1.5 Configuring Serial Parameters ...............................................................................36 4.2.2 Login and User Levels.......................................................................................................37 4.2.3 MA 850 View ....................................................................................................................38 4.3 Gain Setting ..............................................................................................................................39 4.4 Monitoring Alarms......................................................................................................................40 SNMP Management Using Any Standard SNMP Manager ..................................................41 5.1 Traps List ..................................................................................................................................41
Preface Preface Material MA 850 Installation and Configuration Guide XII Specifications.........................................................................................................................43
MA 850 Installation and Configuration Guide 1 1 IInnttrroodduuccttiioonn ttoo tthhee MMAA 885500 SSyysstteemm This chapter provides a description of the MA 850 system, its architecture, installation configurations, operation and required commissioning procedures. 1.1 About MobileAccess MA 850 Figure 1-1. MobileAccess 850 The MA-850 Wi-Fi Module enables 802.11b/g Wi-Fi signals to be combined with other wireless services for simultaneous distribution over the MobileAccess Universal Wireless Network. It can be deployed in a stand-alone mode, for distribution of Wi-Fi only, or it can be connected to other MobileAccess elements (MA-1000/2000) to deliver Wi-Fi along with other wireless services including cellular/PCS, public safety, and WMTS. Unlike traditional Wi-Fi deployments, where 802.11 Access Points (APs) are installed on ceilings and walls throughout the facility, the MA-850 enables organizations to cluster their 802.11 APs together in secure telecom closets. With the clustering approach, IT managers can more easily access APs, which ultimately reduces the operational costs of managing the Wi-Fi network and minimizes disruption within the facility.
About MobileAccess MA 850 MA 850 Installation and Configuration Guide 2 1.1.1 MA 850 Features and Capabilities • Multi-use infrastructure: The same cables and antennas used for Wi-Fi can be used to support the simultaneous extension and distribution of other wireless voice and data services, as follows: o Support for four 802.11b/g AP ports o Mobile services from MobileAccess 1000/2000, ModuLite or Litenna remote units • Simple installation and maintenance: o All active elements are in the telecom shaft or closet o All data and voice services distributed via a common coax cabling and broadband antennas o AP Clustering - 802.11 access points (APs) connect to the MA 850 in telecom closets • Scalable: Additional APs connected as needed to the MA 850 • Management: o Robust system management - Familiar SNMP-based management provides proactive visibility and control of the MA 850 based Wi-Fi infrastructure. o Management through local RS232 connection and remote WEB management • WI-Fi applications transparency - The MA 850 uses discrete, passive antennas to radiate 802.11 signals, providing a coverage architecture that replicates the behaviors necessary to transparently support advanced AP features and location-sensitive Wi-Fi applications. • High-power - With integral constant gain amplifiers combined with its low-loss architecture, the MA 850 offers scalable support for demanding applications such as wireless VoIP
MA 850 Front and Rear Panels MA 850 Installation and Configuration Guide 3 1.2 MA 850 Front and Rear Panels This section describes the MA 850 front- and rear-panel connections and LEDs. 1.2.1 Front Panel Connections and LEDs The front panel contains the antenna connections and mobile services connections, power and local setup connections. The following figure shows the MA 850 front panel. Figure 1-2. MobileAccess 850 Front View Front Panel Ports The following table describes the front panel ports. Front Panel Ports Description Antenna Ports Four n-type female antenna connections Mobile Services Four SMA female connections used in installations that integrate MA 850 with MA 1000 RHUs or MA 2000 services. NOTE: To be terminated with 50 ohm terminations when not in use. Local RS232 connection for local setup (see section 4.1). DC Power connection: 20V to 48V (see 2.3.3) Front Panel LEDs The front panel contains two LEDs, described in the following table. Front Panel LEDs Description Run Internal operation and channel operation status: o Green blinking – unit OK o Off – fault detected in unit o Red blinking – failure of one of the channels PWR (Unlabeled LED adjacent to the power connection). Green – Power OK. Mobile service connections Antenna connections Power Local Setup
MA 850 Front and Rear Panels MA 850 Installation and Configuration Guide 4 1.2.2 Rear Panel Port Connections and LEDs The rear panel contains the 802.11b/g AP connections, Ethernet connection for remote management and antenna sensing connector. Figure 1-3. MobileAccess 850 Rear View Rear Panel Ports The following table describes the rear panel ports. Rear Panel Ports Description 802.11b/g APs Four 802.11b/g connections. (See LED descriptions in the following table). NOTE: To be terminated with 50 ohm terminations when not in use. Connection to control Relevant only when installed as part of a MA 1000 system. Connects to RHU 1000 rear panel Control connector. Routes the antenna sensing (indication of whether antenna is present) to the RHU for monitoring via the management application. (RHU Version 3.1 and higher). Ethernet port Connection to network for configuration and management through a WEB browser. The default IP Address is on the label near the port. Rear Panel 802.11 b/g AP LEDs The rear panel LEDs indicate connection point of corresponding 802.11b/g AP. Rear Panel LEDs Description Blinking green AP connected and working. Red Corresponding AP is not connected or does not transmit. Ethernet port Antenna sense connection 802.11b/g AP connections MAC Address
Unit Architecture MA 850 Installation and Configuration Guide 5 1.3 Unit Architecture MA 850 consists of the following main functional modules: • Interface: Provides interface to the 802.11b/g AP ports. • Gain control mechanism: Gain control to adjust 802.11b/g signals to specific site • Combining and separating mechanism: On the downlink, combines the amplified 802.11b/g signals with the 802.11a AP signals and those of mobile services. On the uplink, separates the signals and routes them to the corresponding ports. • Monitoring and control: Support for WEB monitoring, SNMP MIBs displayed via a standard Web browser and local RS232 and service options. Figure 1-4. MobileAccess 850 Functional Block Diagram 1.4 Installation Configurations MA 850 can be installed in the following configurations: • Standalone – to provide coverage for 802.11b/g services only • Add-on to a MobileAccess 1000 series RHU (with and without MA 1200 add-on) • Add-on to MobileAccess 2000 system NOTE: In all installation types, all the signals are converged via the MA 850 and distributed via the antennas connected to the MA 850 antenna ports.
Installation Configurations MA 850 Installation and Configuration Guide 6 1.4.1 Standalone In this type of installation configuration, MA 850 distributes only 802.11b/g services over the connected antenna infrastructure. Figure 1-5. MA 850 Standalone Installation Configuration 1.4.2 Add-On to MA 1000 RHU The MA 850 can be installed as an add-on unit to a MA 1000 RHU. In this type of installation, the MA 1000 RHU services are routed to the MA 850 inputs where they are integrated with the MA 850 Wi-Fi data services and routed to the MA 850 antenna ports for distribution over a single coax broadband antenna infrastructure. Figure 1-6 MA 850 as Add-On to MA 1000 System
Installation Configurations MA 850 Installation and Configuration Guide 7 1.4.3 Add-on to MA 2000 System The MA 850 can be installed as an (external) add-on unit to the MA 2000 system. In this type of installation, the combined MA 2000 services are routed to the MA 850 inputs where they are integrated with the MA 850 Wi-Fi data services and, through the MA 850 antenna connections, distributed through the same coax broadband antenna infrastructure. Figure 1-7. MA 850 Add-On to MA 2000 System
Signal Distribution in the MA 850 MA 850 Installation and Configuration Guide 8 1.5 Signal Distribution in the MA 850 The MA 850 distributes the 802.11b/g signals from each AP port to the corresponding antenna port. For example, the signals from an AP connected to MA 850 b/g-1 are routed to antenna-1; signals from an AP connected to MA 850 b/g-2 are routed to antenna-2, etc. Note: Mobile services (in installations where MA 850 units are integrated into MA 1000/2000 installations), the mobile services are distributed over the antenna ports corresponding to the SMA connection ports. Figure 1-8. Example of 802.11 Signal Distribution 1.6 Commissioning and Monitoring MA 850 requires no local commissioning. The unit is assigned a default IP address (labeled on its network port) which can be remotely redefined using the procedure in section 4.2.1. No other setup procedure is required: after the unit ports and cables are connected, the unit can be remotely accessed for monitoring and management. In addition, MA 850 provides MIBs that enables viewing traps and configuring the unit through standard SNMP (Version 2.0) managers such as HP OpenView (see Chapter 5 ). NOTE: MA service personnel can perform setup procedures on the MA 850, through a connection from a computer running the Configuration Tool application supplied by MA.
MA 850 Installation and Configuration Guide 9 2 IInnffrraassttrruuccttuurree PPrreeppaarraattiioonn This chapter contains information on the cabling and power requirements for the MA 850 system, as well as the antenna types and access points that can be used. 2.1 Installation Requirements The infrastructure preparation consists of two main phases: 1. Floor Planning: Planning the distribution of the antennas on each floor to provide the required coverage. This phase varies depending on whether the coverage is only for WLAN or includes voice coverage through the existing infrastructure: • For voice and WLAN 802.11b/g coverage- Use only antennas listed in section 2.4.1 table I 2. Telecom Closet Planning: Planning the layout of the devices and cables in the telecom closet or shaft. This includes the MA 850, 802.11 Access Points, cabling and other voice service distribution systems such as MA 1000/2000 that are relevant to the specific installation.
Coaxial Cable Connections MA 850 Installation and Configuration Guide 10 2.2 Coaxial Cable Connections 2.2.1 General Cable Installation Procedures • Observe the general cable installation procedures in accordance with the building codes in your area. • The building code requires that all cabling be installed above ceiling level (where applicable). Each length of cable from the risers to each antenna must be concealed above ceiling. • The cable must be properly supported and maintained straight. This is done either by using tie wraps or cable trays and clamps or hangers every 10 feet (where practical above ceiling level). Where this is not obtainable, the following should be observed: • The minimum bending radius of the supplied ½” coax cable should be 7”. • Cable that is kinked or has a bending radius smaller than 7” must be replaced. • Cable runs that span less than two floors should be secured to mechanical structures that are suitably located. • The cables should be supported only from the building structure. 2.2.2 RF Rules • Use coax ½”, 50ohm, male-to-male N-type, (6-7dB for 1Ghz, 11dB for 2Ghz) for connecting to RHU and RHU ports. • Use coax RG223, 50ohm, male-to-male N-type for RF connections from the BUs to the BTS/RBS and to the RIU. • When using the MobileAccess™ system in an environment in which other indoor coverage systems are installed, it is recommended (where possible) that the antennas are placed at least two meters apart • When bending coax cables, verify that the bending radius does not exceed the coax specifications. • Use only antennas listed in section 2.4.1. • Use a VSWR meter (i.e. Site Master or equivalent) for checking coax cables, including the antennas. (<2). The VSWR must be measured prior to terminating the RHUs in the remote communication rooms • Terminate all unused MA 850 ports with a 50 ohm load
Power Consumption, Connections and Power Supplies MA 850 Installation and Configuration Guide 11 2.3 Power Consumption, Connections and Power Supplies 2.3.1 Power Safety Instructions SAFETY WARNINGS When installing or selecting the power supplies: 1. Be sure to disconnect all power sources before servicing. 2. Calculate the required power according to the requirements of the specific installation and then determine the configuration of the power supplies. The required DC cables will then be determined by the selected PS configuration. 3. Use only UL approved power supplies 4. AC and DC power supply cables – use only the power cords supplied with the units 2.3.2 MA 850 Power Consumption Table 2-1. MobileAccess™ Power Requirements Unit Type Voltage Input Typical Power Consumption Current Consumption MA 850 20 to 48VDC 20W 1.0 A (max) 2.3.3 Types of Power Supplies NOTE: Use only UL approved power supplies with SELV outputs. Table 2-2: MobileAccess™ Power Supplies Power Supply LPS-48V-66W Local AC/DC Converter 66W 2.3.4 Power Connections The power connections vary according to the MA 850 installation topology. The following power supplies are recommended for local power configuration, where power can also be supplied using remote power supply configurations. • Use a dedicated power supply (i.e. LPS-48-66W – refer to the Power Supplies Manual) for the following installations: • MA 850 standalone • Combined with ModuLite MRC or 2000 Cabinet/Lite • LPS-48-100W (recommended) • Combined with the MA 1000 RHU – feeds both modules
In-building Antennas MA 850 Installation and Configuration Guide 12 2.4 In-building Antennas The in-building antennas are connected to the coaxial cable distribution system by jumper cables at various points. The antennas will be mounted on the ceiling tiles and should be exposed. All in-building antenna installations will be such that it will not interfere with indoor traffic and will not enable any person to touch the antennas. • Wideband antennas omni – up to 2.5GHz to support 802.11b/g. Use any of the antennas listed in section 2.4.1 • 50 ohm impedance 2.4.1 Antenna Types Table 2-3. Antennas to be used for 802.11b/g Vendor Catalog number Gain [dBi] Huber+Suhner SWA 0859/360/4/10/V 7 dBi Mars Antennas MA-CM36-15 2 low band 3-4 high band 5 WLAN 802.11b Cellwave A08818DC00-28T0 2.1 Antenna Specialists ASP-3561 2 2.4.2 Antenna Connections NOTE: If the MobileAccess 850 is operated without cellular service, it is required to connect 50ΩΩΩΩ termination points to each of the remote connectors in the unit. A 50 ΩΩΩΩ termination is also required on each unused AP port. • 50 Ω, 1/2” or 3/8” Plenum coax cables • Max cable length (typically): 150’ • 50 ohm terminator on unused connections • For short jumpers (to MRC antenna ports): RG223 2 ft or 10 ft male-to-male coax jumpers
Access Points MA 850 Installation and Configuration Guide 13 2.5 Access Points NOTE: If the MobileAccess 850 is operated without cellular service, it is required to connect 50ΩΩΩΩ termination points to each of the remote connectors in the unit. A 50 ΩΩΩΩ termination is also required on each unused AP port. The following vendor Access Points have been verified and FCC approved. Table 2-4. Approved Access Points Configuration FCC-ID Vendor Catalog number Vendor FCC-ID OJFMA850 Cisco AIR-AP1231G-A-K9 802.11b/g LDK102042 OJFMA850A Cisco AIR-RM22A-A-K9 802.11a LDK102053 OJFMA850C Colubris MAP-320 NKRCM9
MA 850 Installation and Configuration Guide 14 3 IInnssttaallllaattiioonn This chapter contains the installation and connection procedures for various installation configurations. MA 850 may be installed in the following configurations: • Wall mount standalone – mounted directly on the wall with four screws • Mounted onto an MA 1000 RHU • Mount as add-on to an MA 1000 RHU with an MA 1200 add-on unit • Add-on to a MA 2000 system 3.1 Accessory Kits Verify that the supplied accessory kit corresponds to your installation. The accessory kits include a bracket, the required cables and accessories. AK-850-1000 Accessory kit for 850 with 1000 AK-850-1200 Accessory kit for 850 with 1200 AK-850-MDLT Accessory kit for 850 with Modulite AK-850-2000 Accessory kit for 850 with 2000 AK-850-SA Accessory kit for 850 stand alone
Placing the Unit and Recording Location MA 850 Installation and Configuration Guide 15 3.2 Placing the Unit and Recording Location MobileAccess 850 is typically installed in the communication shaft or cabinet of each floor to which WLAN coverage is to be supported. The accessories, mounting and installation procedures vary depending on the installation configuration. NOTE: It is recommended to record the location of the units according to the MAC addresses on the sticker at the rear of the units near the Ethernet port. 3.3 Standalone Wall Mount Installation NOTE: Although it is not required for a stand-alone installation, it is recommended to set the supplied cable 705102101 aside (usually used when MA 850 is installed in an add-on configuration).You will need it if you want to upgrade your system to provide additional coverage options. To install MA 850 wallmount standalone configuration ATTENTION Use SMA wrench for the SMA connectors, do not over tighten the connectors. 1. Mount the MA 850 on the wall using four screws. When mounting, consider the following: • The type of screws used to mount the unit must suit the type of wall construction (cement, bricks, etc.) so that the mount is secure. • The position of the APs and required cable connections. 2. Connect the power. It is recommended to use the following power supply for local power configuration, where power can also be supplied using remote power supply configurations: • Dedicated power supply (i.e. LPS-48-66W – refer to the Power Supplies Manual) 3. Connect the 802.11b/g Access Points to the corresponding ports on the MA 850 rear panel. Refer to section 1.5 for a description of the connections and distribution patterns. NOTE: It is recommended to RESET the unit by removing and reinserting the power connector on the front panel after connecting the APs. 4. Connect the coax antenna cables to the MA 850 unit antenna ports on the MA 850 front panel according to the following instructions: • Use 50 Ω, N-type male to male, 1/2” or 3/8” Plenum coax cables • Max cable length (typically): 150’ 5. Fit 50 ohm terminators on all unconnected SMA, AP and antenna ports.
Add-on to an MA 1000 System Installation MA 850 Installation and Configuration Guide 16 6. Connect the network connection to the MA 850 rear panel network port. NOTE 1: Each unit is pre-assigned an IP address. The address can be modified anytime through a remote connection according to the procedure described in section 4.2.1). NOTE 2: It is recommended to record the location of the units according to the MAC addresses on the sticker at the rear of the units near the Ethernet port. 3.4 Add-on to an MA 1000 System Installation In this type of installation, the MA 850 and MA 1000 RHU are assembled together with a bracket between them. NOTE: It is recommended to mount the MA 850 to the wall, and the MA 1000 on top of the MA 850 (with a bracket between them). However, if a previous MA 1000 RHU is present, you may install the MA850 on top of the existing MA 1000 RHU (with a bracket between them.) To assemble an RHU 1000 onto an MA 850 1. Assemble the supplied bracket to the top of the MA 850, where the notched side of the bracket is towards the rear of the unit. Secure the bracket to the MA 850 unit using the four supplied screws. Figure 3-1. MA 850 and Bracket Assembly 2. Mount the MA 850 and bracket assembly to the wall. When mounting, consider the following: • The type of screws used to mount the unit must suit the type of wall construction (cement, bricks, etc.) so that the mount is secure. • The position of the APs and required cable connections. 3. Mount the MA 1000 RHU to the bracket using the four provided screws. 4. For antenna sensing support (RHU 1000 version 3.1 and higher), connect between the Control connectors at the rear of both units using cable 705102101. Two screws Two screws
Add-on to an MA 1000 System Installation MA 850 Installation and Configuration Guide 17 NOTE: For antenna sensing support in RHU 1000 version 3.0 and lower, upgrade to a higher version according to the MA 850 Upgrade Procedure Guide. 5. Connect the 802.11b/g Access Points to the corresponding ports on the MA 850 rear panel. Refer to section 1.5 for a description of the connections and distribution patterns. NOTE: It is recommended to RESET the unit by removing and reinserting the power connector on the front panel after connecting the APs. 6. Connect the network connection to the MA 850 rear panel network port. NOTE 1: Each unit is pre-assigned an IP address. The address can be modified anytime through a remote connection according to the procedure described in section 4.2.1). NOTE 2: It is recommended to record the location of the units according to the MAC addresses on the sticker at the rear of the units near the Ethernet port. 7. Connect the MA 1000 antenna ports and the MA 850 Mobile Services ports using the four SMA to N-type cables supplied in the accessory kit. NOTE: Be sure the connectors are closed at a 45 degree angle so as not to place stress on the cables. AP status MA 850 MA 1000 RHU Power Antenna connections N-type SMA jumpers (included) 802.11b/g/ AP connections 705102101 connector Ethernet connection MAC Address MA 1000 RHU MA 850
Add-on to an MA 1000 System Installation MA 850 Installation and Configuration Guide 18 8. Connect the power. It is recommended to use the following power supply for local power configuration, where power can also be supplied using remote power supply configurations: • Dedicated power supply (i.e. LPS-48-100W which feeds both modules). Refer to the Power Supplies Manual. 9. Connect the coax antenna cables to the MA 850 unit antenna ports on the MA 850 front panel according to the following instructions: • Use 50 Ω, N-type male to male, 1/2” or 3/8” Plenum coax cables • Max cable length (typically): 150’ 10. Fit 50 ohm terminators on all unconnected SMA, AP and antenna ports.
Add-on to an MA 1000 with MA 1200 MA 850 Installation and Configuration Guide 19 3.5 Add-on to an MA 1000 with MA 1200 In this type of installation, the MA 850 and MA 1000/1200 assembly are separated by a bracket. NOTE: It is recommended to mount the MA 850 to the wall, and the MA 10001200 assembly on top of the MA 850 (with a bracket between them). However, if a previous MA 1000/1200 assembly exists, you may install the MA850 on top of the existing assembly, (with a bracket between them.) To assemble an RHU 1000 onto an MA 850 1. Assemble the supplied bracket to the top of the MA 850, where the notched side of the bracket is towards the rear of the unit. Secure the bracket to the MA 850 unit using the four supplied screws. Figure 3-2. MA 850 and Bracket Assembly Two screws Two screws
Add-on to an MA 1000 with MA 1200 MA 850 Installation and Configuration Guide 20 2. Mount the MA 850 and bracket assembly to the wall. When mounting, consider the following: • The type of screws used to mount the unit must suit the type of wall construction (cement, bricks, etc.) so that the mount is secure. • The position of the APs and required cable connections. 3. Assemble the MA 1000/1200 assembly to the 850 bracket. 4. For antenna sensing support (RHU 1000 version 3.1 and higher), connect between the Control connectors at the rear of both units using cable 705102101. NOTE: For antenna sensing support in RHU 1000 version 3.0 and lower, upgrade to a higher version according to the MA 850 Upgrade Procedure Guide. 5. Connect the 802.11b/g Access Points to the corresponding ports on the MA 850 rear panel. Refer to section 1.5 for a description of the connections and distribution patterns. NOTE: It is recommended to RESET the unit by removing and reinserting the power connector on the front panel after connecting the APs. 6. Connect the network connection to the MA 850 rear panel network port. NOTE 1: Each unit is pre-assigned an IP address. The address can be modified anytime through a remote connection according to the procedure described in section 4.2.1). NOTE 2: It is recommended to record the location of the units according to the MAC addresses on the sticker at the rear of the units near the Ethernet port. 705102101 connector 802.11b/g/ AP connections Ethernet connection MAC Address MA 1000 RHU MA 850
Add-on to an MA 1000 with MA 1200 MA 850 Installation and Configuration Guide 21 7. Connect the MA 1000 antenna ports and the MA 850 Mobile Services ports using the four SMA to N-type cables supplied in the accessory kit. NOTE: Be sure the connectors are closed at a 45 degree angle so as not to place stress on the cables. Figure 3-3. Connection of MA 850 and MA 1000 Service Ports 8. Connect the power. It is recommended to use the following power supply for local power configuration, where power can also be supplied using remote power supply configurations: • Dedicated power supply (i.e. LPS-48-100W which feeds both modules). Refer to the Power Supplies Manual. 9. Connect the coax antenna cables to the MA 850 unit antenna ports on the MA 850 front panel according to the following instructions: • Use 50 Ω, N-type male to male, 1/2” or 3/8” Plenum coax cables • Max cable length (typically): 150’ 10. Fit 50 ohm terminators on all unconnected SMA, AP and antenna ports. MA 1200 MA 850 MA 1000 Antennas N-type SMA jumpers (included)
Add-on to an MA 2000 System MA 850 Installation and Configuration Guide 22 3.6 Add-on to an MA 2000 System MA 850 may be integrated into the MA 2000 system using one of the following installations: • Installing it directly on the MA 2000 RC top panel (using the supplied plate); • Mounting it on a rack (using the supplied plate); • Wall-mount near the MA 2000 cabinet. NOTE: The coax outputs of the cabinet are connected to the appropriate ports on the MA 850 and the antennas are connected directly to the MA 850 module. 3.6.1 MA 850 RC 2000 Assembly 1. Assemble two side brackets to the plate sides as illustrated in Figure 3-4. 2. Assemble the MA 850 module to the supplied bracket using the four screws and washers as illustrated below. Figure 3-4. MA 850 Rack Installation 3. Assemble the plate to the MA 2000 RC by securing the brackets to the cabinet sides as illustrated below. Side bracket assembly Side bracket assembly
Add-on to an MA 2000 System MA 850 Installation and Configuration Guide 23 Figure 3-5. Illustration of MA 850 Mounted on MA 2000 RC 4. Connect the RC antenna ports to the MA 850 front panel port connectors as illustrated below. Figure 3-6. Illustration of RC Antenna port connections 5. Connect the antennas to the MA 850 antenna ports.Connection to Remote Cabinet antenna ports
Add-on to an MA 2000 System MA 850 Installation and Configuration Guide 24 3.6.2 MA 850 Rack Mount 1. Assemble the side brackets as illustrated in Figure 3-4. 2. Assemble the MA 850 module to the supplied bracket using the four screws and washers. 3. Mount the assembly in the rack using the side brackets. Figure 3-7. MA 850 to Bracket Installation 4. Connect the RC antenna ports to the SMA connectors on the MA 850 front panel. 5. Connect the antenna to the MA 850 antenna ports. 3.6.3 MA 850 Wall Mount Installation The MA 850 may be mounted independently on the wall near the RC cabinet. • Connect the RC antenna ports to the SMA connectors on the MA 850 front panel. • Connect the antenna to the MA 850 antenna ports.
MA 850 Installation and Configuration Guide 25 4 CCoonnffiigguurraattiioonn aanndd MMaannaaggeemmeenntt It is required to perform the following configuration procedures: • Change the default IP address • Configure the unconnected antenna ports (if not all antennas are connected) The configuration is performed through a remote connection using a standard Web browser application (i.e. Explorer). After configuring the unit, each channel and the corresponding element may be monitored. NOTE 1: The unit may be configured either before or after the installation. NOTE 2: Professional installers may configure the unit through a local connection to a computer running the MA 850 Setup Tool application. NOTE 3: A local connection has priority over a WEB connection. A WEB connection will not be operational if there already is a local connection and the unit stop responding if a local connection is initiated while a WEB session is open.
Local Configuration and Monitoring MA 850 Installation and Configuration Guide 26 4.1 Local Configuration and Monitoring This procedure is performed through the MA 850 Customer Tool application installed and launched from a computer that is locally connected to the MA 850 unit. For professional installer only This procedure is performed through the MA 850 Customer Tool application installed and launched from a computer that is locally connected to the MA 850 unit. 4.1.1 Getting Started 1. Install the 850 MA Customer Tool application on your computer. 2. Locally connect to the MA 850 Local connector using the RS232 9-pin cable provided with the MA 850 unit. 3. Launch the application on the computer. The MA 850 Customer Tool dialog appears. Figure 4-1. Connecting to the MA 850 4. Under Serial Port, Select the com port corresponding to the currently connected computer RS232 port and click Connect. The dialog options are described in the following sections. Set Comm port Connect
Local Configuration and Monitoring MA 850 Installation and Configuration Guide 27 4.1.2 MA 850 Customer Tool Window Description The MA 850 Customer Tool window is displayed according to the instructions in the previous section. The window provides the channel configuration and monitoring options. It is divided into the following areas: • General information – versions, etc. • Four channel areas – contain channel gain setting, antenna connections and channel status • AP Status - detected AP connection • Connection options – at the bottom left side of the window Figure 4-2. MA 850 Customer Tool Dialog General information Channel and antenna configuration
Local Configuration and Monitoring MA 850 Installation and Configuration Guide 28 4.1.3 Configuration Using MA 850 Customer Tool 1. It is assumed that you are now locally connected to the MA 850 and have launched the Customer Tool on you computer according to the instructions in the previous sections. 2. All antennas are configured by default as being connected (Antenna Select – Enable). For channels where an antenna is not connected, under Antenna Select, choose Disable. The Antenna Sense for the corresponding antenna will indicate N/A (not applicable). 3. By default, the Gain for each channel is set to 0dB. To change the coverage area per channel, change the Gain for the specific channel. 4.1.4 Monitoring Using MA 850 Customer Tool The MA 850 Customer Tool enables the user end-to-end monitoring of the channel status and elements. MA 850 Customer Tool Monitoring functions include: • Antenna connection status – Antenna Sense for the corresponding channel, where: • OK – antenna connection detected • Fail – antenna not detected • N/A – Antenna Select is set to Disable, meaning that an antenna is not connected to the corresponding port
Remote - Web Browser Session MA 850 Installation and Configuration Guide 29 • Channel status – under Amp 1 to Amp 4 for the corresponding channel: • OK – channel OK • Fail – channel failure • AP Status: • OK – AP detected • Fail – AP not detected at the port. 4.2 Remote - Web Browser Session NOTE: Be sure that there is not an open local session (section 4.1) to the MA 850 unit before you attempt to open a remote session to the same unit; otherwise, the unit may stop responding. MA 850 whose SNMP parameters are defined may be connected to the network through an Ethernet connection and assigned addresses either through dynamic (DHCP) or static address assignment methods. The MA 850 units may then be remotely managed from any Web Browser by connecting to the IP Address of the specific MA 850 unit or through any Network Operating Center (NOC) using SNMP. Once the network connections have been defined (section 4.2.1), the following operations may be performed remotely through a Web browser: • Configure gain setting for each channel (section 4.3) • View alarms (section 4.4) Figure 4-3. MA 850 Remote Management
Remote - Web Browser Session MA 850 Installation and Configuration Guide 30 4.2.1 IP Configuration Procedure MA 850 units connected to the network may be assigned either dynamic IP Addresses through DHCP or static IP addresses (for networks without DHCP). The addresses may be assigned from a single location using the Lantronix DeviceInstall application supplied with the units. The IP configuration procedure consists of the following steps: • Installing and launching the Lantronix DeviceInstaller application on your computer. • Connecting to the Network, page 30 • Performing Auto-Discovery, page 30 • For networks without DHCP – Assigning a Static IP Address, page 31 • Configuring the SNMP Parameters, page 34 4.2.1.1 Connecting to the Network Connect each MA 850 unit first to the network and then to the power cable. NOTE: It is recommended to record the location of the units according to the MAC addresses on the sticker at the rear of the units near the Ethernet port. 4.2.1.2 Performing Auto-Discovery NOTE: Be sure the installed version is 3.6 or higher. 1. Install and launch the Lantronix DeviceInstaller application on your computer. Figure 4-4. DeviceInstaller dialog 2. In the DeviceInstaller main window toolbar, click Search to perform auto-discovery. The MA 850 units currently in the network will be identified and listed in the window according to: • Type - communication hardware version - xPort-01 or xPort-03
Remote - Web Browser Session MA 850 Installation and Configuration Guide 31 • Hardware Address – MAC address • Additional identification parameters that may be available 3. For networks with DHCP: • The dynamically assigned IP Address will also be listed in the IP Address column. 4. For networks without DHCP: • Disregard the data displayed in the IP Address column and assign a Static IP address according to Assigning a Static IP Address, page 31. What next ? Define the SNMP parameters according to Configuring the SNMP Parameters, page 34. 4.2.1.3 Assigning a Static IP Address NOTE: This procedure requires the MAC address of the MA 850, which is found on the label located at the rear of the unit. Perform the following procedure for each of the MA 850 units listed in the Lantronix DeviceInstaller main window which are to be manually assigned IP Addresses. 1. Select the MA 850 unit and click the icon Assign IP in the toolbar. Figure 4-5. Assigning Static IP Address The Device Identification window appears, showing the MAC address of the selected MA 850 unit.
Remote - Web Browser Session MA 850 Installation and Configuration Guide 32 Figure 4-6. MAC Address 2. Click Next. The IP Address Assignment Method window appears. Figure 4-7. Static IP Address 3. Select Assign a specific IP address; then, click Next. The IP Settings window appears.
Remote - Web Browser Session MA 850 Installation and Configuration Guide 33 Figure 4-8. Static IP Address Definition 4. Enter the IP Address, Subnet Mask and Default Gateway values; then, click Next. The Assignment window appears. Figure 4-9. Assignment Window 5. Click Assign to assign the MA 850 unit the defined parameters. Once the parameters have been assigned, the message ‘Completed Successfully’ appears and the Finish button is enabled.
Remote - Web Browser Session MA 850 Installation and Configuration Guide 34 Figure 4-10. Finish Static IP Address Definition 6. Click Finish. The Device Installer Main window reappears and the installed unit will be listed in the window. What next? Define the SNMP parameters according to Configuring the SNMP Parameters, page 34. 4.2.1.4 Configuring the SNMP Parameters Configure the SNMP Community and Trap destination addresses according to the instructions in this section. NOTE: The required communication parameters are pre-set for each MA 850 unit. However if you do not succeed in connecting to the Telnet application, verify the serial communication parameter page 36 section 4.2.1.5 1. Select the MA 850 unit which will be configured (may be identified according to its MAC address value) and click the Telnet button in the toolbar. The Telnet dialog shows the IP address of the currently connected MA 850 unit. Figure 4-11. Telnet IP Address window
Remote - Web Browser Session MA 850 Installation and Configuration Guide 35 2. Click OK and immediately press Enter to go into Setup Mode. The current settings will be displayed, followed by the Change Setup menu. Change Setup: 0 Server configuration 1 Channel 1 configuration 3 SNMP configuration 7 factory defaults (for manufacturer use only DO NOT SELECT!!) 8 exit without save 9 save and exit Your choice ? 3. Enter 3 (SNMP Configuration). 4. Set the SNMP Read and Write community names and the SNMP traps destination addresses (up to three addresses can be defined) by responding with Y to the prompt Set the Gateway IP Address and defining the Address (as illustrated below). SNMP community name for read (): public SNMP community name for write (): private Enter IP addresses for SNMP traps: 1: (000) 192.(000) 168.(000) 10.(000) 22 2: (000) .(000) .(000) .(000) 3: (000) .(000) .(000) .(000) 5. Press Enter to run through the rest of the parameters. When the Setup Menu is displayed again, select 9 – Save and Exit.
Remote - Web Browser Session MA 850 Installation and Configuration Guide 36 4.2.1.5 Configuring Serial Parameters This section describes how to verify and configure the serial communication parameters for each MA 850 unit. 1. From the DeviceInstaller Main window, select the MA 850 unit to be configured and click the Configure button the toolbar. The Configure Device dialog appears. Figure 4-12. Current Serial Port Parameters 2. Click the Ports tab and then the Edit Settings… button. The Port Properties dialog appears. Figure 4-13. Port Properties 3. Set the parameters as follows: Baud Rate 19200, Data Bits 8, Parity None, Stop Bits 1, Flow Control None; then, click OK. The DeviceInstaller Main window appears.
Remote - Web Browser Session MA 850 Installation and Configuration Guide 37 4.2.2 Login and User Levels You may login to the MA 850 unit through any Web browser. Two user levels are available: • guest (guestpass) – monitoring options only • admin (adminpass) – monitoring and configuration options NOTE: The password is case sensitive – use lower case letters. To login to the MA 850 configuration application 1. Run a Web Browser application (i.e. Internet Explorer). 2. Enter the IP Address of the MA 850 unit. (i.e. http://192.168.10.127). The Login dialog appears. The application version is displayed at the top of the window. Figure 4-14. Login Window 3. Select the User (guest or admin) and the password; where admin has configuration privileges. 4. Click Login. The Main configuration window appears. The window shows the current configuration (Active Configuration) and provides access to configuration and monitoring options. The Main window is described in the following section. Application Version
Remote - Web Browser Session MA 850 Installation and Configuration Guide 38 4.2.3 MA 850 View Upon login, the MA 850 View shows the current 802.11b/gs AP and antenna connections. Menu options on the left side provide access to various configuration options as described in Table 4-1. Element color indications is described in Table 4-2. NOTE: The display is refreshed automatically; however, if necessary, be sure to use the application Refresh button in the menu options (and not the Web Browser refresh). Figure 4-15. Main Window Table 4-1. MA 850 View Menu Options Menu Option Description Login/Logout Click to login using a different user level Active config Displays the current configuration Alarms Alarm monitoring Refresh Used to refresh the display. Setting Gain setting (default = 0) and Redundancy enable/disable options Menu options Access Points Antenna connection routes Internal channels Antenna connection status
Gain Setting MA 850 Installation and Configuration Guide 39 Table 4-2. MA 850 View Color Indications Option Description Green OK Red Error indication: Red AP – an AP is not connected or faulty. Red antenna – antenna not detected by antenna sense mechanism Red Amp – channel malfunction identified in the MA 850 unit Purple Location (not status) of backup AP in one-AP or two-AP configurations with in which the redundancy option is enabled. Only if the backup AP is activated (upon failure of a default AP), does its color indicate status (green, red). Gray Not relevant in current configuration – whether an AP is physically connected to the specific port or not. 4.3 Gain Setting The default gain for each channel is set to 0dB. MA 850 enables the authorized user (admin level) to adjust the gain for every channel to counteract changes in the environment. For example, you may want to reduce the coverage area of a channel to prevent interference. Or, the output of an AP with a low power (<20dBm) can be increased using the gain value. To change the gain setting of a channel 1. Click the Setting button in the Main window. The Gain Setting options appear. Figure 4-16. Gain Setting Options Gain Setting options
Monitoring Alarms MA 850 Installation and Configuration Guide 40 2. For the relevant channel, change the gain. Range = -10 to +5 dB 3. Click Accept. The gain value for the channels at the unit is displayed under the Gain Value column. 4.4 Monitoring Alarms MA 850 provides the following alarms, which may be viewed by clicking the Alarms button in the Main window: • Access Point Sense – senses the connection of configured APs • Low power – internal channel operation status • Antenna sense – senses connected antennas. This option can be disabled for antennas that are not connected Figure 4-17. Alarms Window
Traps List MA 850 Installation and Configuration Guide 41 5 SSNNMMPP MMaannaaggeemmeenntt UUssiinngg AAnnyy SSttaannddaarrdd SSNNMMPP MMaannaaggeerr The MA 850 packages provide MIBSs that enable standard SNMP (Version 2.0) managers such as HP OpenView to view event traps sent by the MA 850 unit and to configure the unit. One MIB file is provided: MA-XPORT850-MIB– describes the architecture of the managed elements and contains the events in the system NOTE: These traps provide a general indication of the type of failure. The MA 850 enables identifying the source of the problem and system monitoring parameters. 5.1 Traps List NOTE: Traps are only sent to defined trap destinations (section 4.2.1.4). The following traps are provided: Table 5-1. List of MA 850 Traps Name Type OID Description x850SystemOnNotify NOTIFICATION-TYPE 90.4.2.0.1 System On. x850SerialNotify NOTIFICATION-TYPE 90.4.2.0.2 serial communication status failed success x850ntenaConnectedNotify NOTIFICATION-TYPE 90.4.2.0.3 Antenna Connected x850ntenaDisconnectedNotify NOTIFICATION-TYPE 90.4.2.0.4 Antenna Disconnected x850OutPowerLowNotify NOTIFICATION-TYPE 90.4.2.0.5 Out Power Low x850OutPowerNormalNotify NOTIFICATION-TYPE 90.4.2.0.6 Out Power Normal x850PConnectedNotify NOTIFICATION-TYPE 90.4.2.0.7 AP Connected x850PDisconnectedNotify NOTIFICATION-TYPE 90.4.2.0.8 AP Disconnected x850MPRecoveredNotify NOTIFICATION-TYPE 90.4.2.0.11 AMP Recovered x850MPFailedNotify NOTIFICATION-TYPE 90.4.2.0.12 AMP Failed
Traps List MA 850 Installation and Configuration Guide 42 To view the traps using any standard SNMP manager NOTE: It is assumed that the IP Address of at least one destination is already defined. From a computer configured as a trap destination (configured to receive the traps), load the two MIB files to the SNMP manager. The following figure shows the MIB tree that includes the loaded MobileAccess 850 file. Figure 5-1. MIB Tree with Loaded MobileAccess 850 Files
MA 850 Installation and Configuration Guide 43 SSppeecciiffiiccaattiioonnss 802.11b/g RF Parameters Bandwidth 2400 - 2485 MHz Gain TX 0 dB per port Gain RX 10 dB NF RX 7 dB Flatness ±1.5 dB Mobile Services/WMTS Parameters MA-850 MA-850U Mobile Services Cell WMTS PCS WMTS Cell WMTS DCS WMTS UMTS Band (MHz) 608-960 1395-1990 608-960 1395-1880 1920-2170 Insertion Loss (dB/port) 1.0 2.0 1.0 2.0 3.0 Flatness (dB) +/- 0.5 +/- 1.0 +/- 0.5 +/- 1.0 +/- 1.5 RF Connections 802.11 b/g (4) SMA Female, 50 ohm Mobile Services (4) SMA Female, 50 ohm Antenna Ports (4) N-type Female, 50 ohm Management Configuration and monitoring via local RS232 connection and remote connection through a Web browser application. Power Power 20 to 48 VDC; 20W Physical Specification Dimensions 242 mm x 279 mm x 38 mm (9.54 in x 10.98 in x 1.5 in) Weight 2.82 kg (6.2 lb)
Traps List MA 850 Installation and Configuration Guide 44 Environmental Specifications Temperature Operating 0°C to +50°C (32°F to 122°F) Storage -20°C to 85°C (-4°C to 185°C) Humidity Operating 95% (non-condensing) Storage 95% (non-condensing) Standards and Approvals USA FCC–47 CFR 15 UL 60950-1 CAN/CSA C22.2 No 60950 Ordering Information 850 WLAN Module 850-U WLAN module with UMTS support Accessory Kits for mounting MA-850 with other MobileAccess elements: AK-850-1000 MA-850 with MA-1000 AK-850-1200 MA-850 with MA-1200 AK-850-MDLT MA-850 with Modulite AK-850-2000 MA-850 with MA-2000 AK-850-SA MA-850 standalone

Navigation menu