Corning Optical Communication LITENNA0LF0SB0 In Building Repeater User Manual Litenna Data Sheet

Corning Optical Communication Wireless In Building Repeater Litenna Data Sheet

Contents

Litenna Data Sheet

In-Building RF Distribution System©Sadna 5/2000© Foxcom Wireless 2000. Doc. No. 42-13-002-20-AE-mail: salesna@foxcomwireless.comWebsite: www.foxcomwireless.com8150 Leesburg PikeSuite 600Vienna, Virginia 22182Tel: 703-848-0200Fax: 703-848-0280Foxcom Wireless Inc.Ofek One Center - Building BNorthern Industrial ZoneLod, Israel 71293Tel: +972-8-918-3888Fax: +972-8-918-3844Foxcom Wireless Ltd.Ordering InformationProductSingle Band Family9A110 = AMPS/TDMA 8009A112= LMR 8009A130 = CDMA 8009A220 = GSM 9009A320 = GSM 18009A330 = CDMA 18009A410 = TDMA 19009A420 = GSM 19009A430 = CDMA 1900Dual Band Family9B320 = Dual band GSM 900/1800ReservedPartRHU = Remote Hub UnitB4U = Base Unit Four PortsB8U = Base Unit Eight Ports9XXXX - XXX - XXMechanical DimensionsThe Litenna™, fiberoptic based distribution system, enables wireless service operators andintegrators to provide seamless coverage and enhanced cellular capacity for In-building applications.Comprised of a Base Unit that connects up to eight Remote Hub Units (driving up to four antennaseach), the fiberoptic technology based system is modular and expandable to a wide variety ofstructure sizes and configurations. The Litenna supports wireless voice and data applications,offering a cost-effective and flexible solution for coverage enhancement.E-mail: sales@foxcomwireless.comCompliant with all existing wireless voice and data servicesSupports GPRS, EDGE, CDPD and WAP technologiesEasily upgradable from single band to multi band and future services, 3G readySingle infrastructure for multiple services/ multiple operatorsBuilt-in alarms / monitors for all channelsSinglemode fiberoptic cables connect between the system unitsEasy to design, install and maintainFor Indoor use only.All specifications are subject to change without prior notice.Order CodeSC/APC-J-5LPS-25-48LPS2-100-48LPS2-300-48Available AccessoriesSC/APC JumperLocal Power SupplyFully Redundant Power SupplyFully Redundant Power Supply5m25W110/220V100W110/220V300W110/220VSupported StandardsUL/DL (MHz)CDMA 800TDMA/AMPS 800LMR 800GSM 900CDMA 1800GSM 1800CDMA 1900TDMA 1900GSM 1900824-849 / 869-894806-824 / 851-869890-915 / 935-9601715-1780 / 1805-18701710-1785 / 1805-18801850-1910 / 1930-1990STANDARDSRemote Hub Unit19”12”1UBase UnitBase Unit Front PanelBase Unit Back Panel11”8”Remote Hub Unit Front PanelRF In RF OutAlarmOptical In/OutOptical InOptical OutCellular Antennas2”Litenna™ Base UnitFiberopticTx #1FiberopticTx #8FiberopticRx #1FiberopticRx #8Down LinkUp LinkRF Out(Sector 1)RF Out(Sector 2 Opt.)RF In(Sector 1)RF In(Sector 2 Opt.)Litenna™ Block DiagramLitenna™ RHU #8FiberopticRx #8FiberopticTx #8HPALNAFilters & DiplexersRFRFLitenna™ RHU #1FiberopticRx #1FiberopticTx #1HPALNAFilters & DiplexersRFRF
Composite Cable SpecificationsSpecificationsCable TypeCopper DiameterStandard ComplianceSingle Mode Fiber 2.8 mm Tight Buffer Jacket18AWGUL Listed Cable / IEC -332-33Absolute Maximum RatingSpecificationsTotal Input RF Power (dBm)Power Supply (V)Operating Temperature (ºC)1Storage Temperature (ºC)Base Unit Remote Hub Unit1. For extended temperature range (-20 to 60ºC) contact Foxcom Wireless.20600 to +50-40 to +8510600 to +50-40 to +85General Technical Specifications1310±103dB9/125 single mode0.5 dB maximum≥1.0500 @ 48VDC / 250 @ 27VDC2000Optical SpecificationsOther Specifications1. Distance increases with correlation to cable diameter.Wavelength (nm)Max. Optical budget (dB)Fiber typeOptical loss per mated pair connectorsOptical output power (mW)Distance between BU and RHU (m) @18AWG(1) DC power is supplied via composite cable DC power is supplied directly to RHUPhysical SpecificationsSpecifications Base Unit Remote Hub Unit18-48VDC - DC inputor: 27-48VDC - fed through composite cable10 W max. Singleband15 W max. Dualband11”W x 8”L x 2”HN Type FemaleSC/APCPowerDimensionsRF ConnectorOptical Connector18-48VDC8W max. when driving 8 RHUs4W max. when driving 4 RHUs19” x 1UN Type FemaleSC/APCDownlinkNominal Output Power At AntennaPort Per Carrier per band(dBm) Composite 2 carriers 3 carriers 10 carrieNominal Gain at Antenna Port (dB)Nominal Input PowerPer Carrier per band (dBm) Composite 2 carriers 3 carriers 10 carriersGain Flatness (dB) Over Band Over BlockMax. Second Order IntermodulationDistortion (IMD) (dBm)Max. Intermodulation Distortion (IMD)(dBm)Waveform Quality ( ) at Max. PowerSpurious Emission (BW=30kHz) (dBc)System Group Delay (µ s)Link SpecificationsCDMA GSM LMR TDMA–-13>0.96>45@± 885 KHz<0.1–-13–––RF Specifications1900171412710742-3±2.0±1.48002017151014631-4±1.5±1.28002017151014631-4±1.5±1.2–-13–––Dual Band900/1800107––730––±1.8–-36/-30-36/-30––1900171412710742-3±2.0±1.4–-13180011861741-1-6±1.8––-30–––90011861741-1-6±1.8––-36190014109–1041-1–±2.0±1.4180014109–1041-1–±1.8–80014109–140-3-5–±1.5±1.2UplinkNominal Gain At Antenna Port (dB)Min. Input IP3 (dBm)Max. NF (dB)Gain Flatness (dB) Over Band Over BlockSFDR (dB)Waveform Quality ( ) at Max. PowerSpurious Emission (BW=30kHz) (dBc)System Group Delay (µ s)8007-220±1.5±1.2Link SpecificationsCDMA GSM LMR18007-220±1.8–19007-216±2.0±1.4749007-220±1.8–18007-220±1.8–65–––19007-216±2.0±1.4TDMADual Band900/18007-220±1.8–65–––8007-220±1.5±1.272–––8007-220±1.5±1.27219007-216±2.0±1.47472>0.96>45@± 885 KHz<0.1–––Alarm SpecificationsBase Unit AlarmsThe Litenna™ Base Unit alarms are Dry Contacts and Open Collector types. The Dry Contacts opens when the alarm is active. The Open Collector will sink up to 30mAunder alarm condition. All alarms are connected to the Base Unit rear panel 25 pin D type connectors.AlarmOptical LinkFunctionIndicates that the two direction optical link between Base Unit and Remote Hub Unit are not functioningLED SpecificationsBase Unit LEDsThe Base Unit has three types of LEDs. One type indicates the power status. One type indicates that the lasers are functioning. One type indicates the status of linkoperations between the Base Unit and the RHU-one LED for every RHU. All LEDs should be on when the unit is in operation.LED NameChannel 1..8Lasers 1..4Lasers 5..8DCLED FunctionIndicates that both directions of the optical link, between Base Unit and Remote Hub Unit,is functioning - one LED for every RHU link.Indicates that laser circuitry for RHU 1-4 is functioning correctly.Indicates that laser circuitry for RHU 5-8 is functioning correctly.Indicates that the power is on.Remote Hub Unit LEDsOn the Front Panel of the RHU there are two LEDs. Both LEDs should be on when the unit is in operation.LED Name LED FunctionIndicates that the Received Optical Power is functioning within specifications.Indicates that the power is on.Opt.DC
Composite Cable SpecificationsSpecificationsCable TypeCopper DiameterStandard ComplianceSingle Mode Fiber 2.8 mm Tight Buffer Jacket18AWGUL Listed Cable / IEC -332-33Absolute Maximum RatingSpecificationsTotal Input RF Power (dBm)Power Supply (V)Operating Temperature (ºC)1Storage Temperature (ºC)Base Unit Remote Hub Unit1. For extended temperature range (-20 to 60ºC) contact Foxcom Wireless.20600 to +50-40 to +8510600 to +50-40 to +85General Technical Specifications1310±103dB9/125 single mode0.5 dB maximum≥1.0500 @ 48VDC / 250 @ 27VDC2000Optical SpecificationsOther Specifications1. Distance increases with correlation to cable diameter.Wavelength (nm)Max. Optical budget (dB)Fiber typeOptical loss per mated pair connectorsOptical output power (mW)Distance between BU and RHU (m) @18AWG(1) DC power is supplied via composite cable DC power is supplied directly to RHUPhysical SpecificationsSpecifications Base Unit Remote Hub Unit18-48VDC - DC inputor: 27-48VDC - fed through composite cable10 W max. Singleband15 W max. Dualband11”W x 8”L x 2”HN Type FemaleSC/APCPowerDimensionsRF ConnectorOptical Connector18-48VDC8W max. when driving 8 RHUs4W max. when driving 4 RHUs19” x 1UN Type FemaleSC/APCDownlinkNominal Output Power At AntennaPort Per Carrier per band(dBm) Composite 2 carriers 3 carriers 10 carrieNominal Gain at Antenna Port (dB)Nominal Input PowerPer Carrier per band (dBm) Composite 2 carriers 3 carriers 10 carriersGain Flatness (dB) Over Band Over BlockMax. Second Order IntermodulationDistortion (IMD) (dBm)Max. Intermodulation Distortion (IMD)(dBm)Waveform Quality ( ) at Max. PowerSpurious Emission (BW=30kHz) (dBc)System Group Delay (µ s)Link SpecificationsCDMA GSM LMR TDMA–-13>0.96>45@± 885 KHz<0.1–-13–––RF Specifications1900171412710742-3±2.0±1.48002017151014631-4±1.5±1.28002017151014631-4±1.5±1.2–-13–––Dual Band900/1800107––730––±1.8–-36/-30-36/-30––1900171412710742-3±2.0±1.4–-13180011861741-1-6±1.8––-30–––90011861741-1-6±1.8––-36190014109–1041-1–±2.0±1.4180014109–1041-1–±1.8–80014109–140-3-5–±1.5±1.2UplinkNominal Gain At Antenna Port (dB)Min. Input IP3 (dBm)Max. NF (dB)Gain Flatness (dB) Over Band Over BlockSFDR (dB)Waveform Quality ( ) at Max. PowerSpurious Emission (BW=30kHz) (dBc)System Group Delay (µ s)8007-220±1.5±1.2Link SpecificationsCDMA GSM LMR18007-220±1.8–19007-216±2.0±1.4749007-220±1.8–18007-220±1.8–65–––19007-216±2.0±1.4TDMADual Band900/18007-220±1.8–65–––8007-220±1.5±1.272–––8007-220±1.5±1.27219007-216±2.0±1.47472>0.96>45@± 885 KHz<0.1–––Alarm SpecificationsBase Unit AlarmsThe Litenna™ Base Unit alarms are Dry Contacts and Open Collector types. The Dry Contacts opens when the alarm is active. The Open Collector will sink up to 30mAunder alarm condition. All alarms are connected to the Base Unit rear panel 25 pin D type connectors.AlarmOptical LinkFunctionIndicates that the two direction optical link between Base Unit and Remote Hub Unit are not functioningLED SpecificationsBase Unit LEDsThe Base Unit has three types of LEDs. One type indicates the power status. One type indicates that the lasers are functioning. One type indicates the status of linkoperations between the Base Unit and the RHU-one LED for every RHU. All LEDs should be on when the unit is in operation.LED NameChannel 1..8Lasers 1..4Lasers 5..8DCLED FunctionIndicates that both directions of the optical link, between Base Unit and Remote Hub Unit,is functioning - one LED for every RHU link.Indicates that laser circuitry for RHU 1-4 is functioning correctly.Indicates that laser circuitry for RHU 5-8 is functioning correctly.Indicates that the power is on.Remote Hub Unit LEDsOn the Front Panel of the RHU there are two LEDs. Both LEDs should be on when the unit is in operation.LED Name LED FunctionIndicates that the Received Optical Power is functioning within specifications.Indicates that the power is on.Opt.DC
In-Building RF Distribution System©Sadna 5/2000© Foxcom Wireless 2000. Doc. No. 42-13-002-20-AE-mail: salesna@foxcomwireless.comWebsite: www.foxcomwireless.com8150 Leesburg PikeSuite 600Vienna, Virginia 22182Tel: 703-848-0200Fax: 703-848-0280Foxcom Wireless Inc.Ofek One Center - Building BNorthern Industrial ZoneLod, Israel 71293Tel: +972-8-918-3888Fax: +972-8-918-3844Foxcom Wireless Ltd.Ordering InformationProductSingle Band Family9A110 = AMPS/TDMA 8009A112= LMR 8009A130 = CDMA 8009A220 = GSM 9009A320 = GSM 18009A330 = CDMA 18009A410 = TDMA 19009A420 = GSM 19009A430 = CDMA 1900Dual Band Family9B320 = Dual band GSM 900/1800ReservedPartRHU = Remote Hub UnitB4U = Base Unit Four PortsB8U = Base Unit Eight Ports9XXXX - XXX - XXMechanical DimensionsThe Litenna™, fiberoptic based distribution system, enables wireless service operators andintegrators to provide seamless coverage and enhanced cellular capacity for In-building applications.Comprised of a Base Unit that connects up to eight Remote Hub Units (driving up to four antennaseach), the fiberoptic technology based system is modular and expandable to a wide variety ofstructure sizes and configurations. The Litenna supports wireless voice and data applications,offering a cost-effective and flexible solution for coverage enhancement.E-mail: sales@foxcomwireless.comCompliant with all existing wireless voice and data servicesSupports GPRS, EDGE, CDPD and WAP technologiesEasily upgradable from single band to multi band and future services, 3G readySingle infrastructure for multiple services/ multiple operatorsBuilt-in alarms / monitors for all channelsSinglemode fiberoptic cables connect between the system unitsEasy to design, install and maintainFor Indoor use only.All specifications are subject to change without prior notice.Order CodeSC/APC-J-5LPS-25-48LPS2-100-48LPS2-300-48Available AccessoriesSC/APC JumperLocal Power SupplyFully Redundant Power SupplyFully Redundant Power Supply5m25W110/220V100W110/220V300W110/220VSupported StandardsUL/DL (MHz)CDMA 800TDMA/AMPS 800LMR 800GSM 900CDMA 1800GSM 1800CDMA 1900TDMA 1900GSM 1900824-849 / 869-894806-824 / 851-869890-915 / 935-9601715-1780 / 1805-18701710-1785 / 1805-18801850-1910 / 1930-1990STANDARDSRemote Hub Unit19”12”1UBase UnitBase Unit Front PanelBase Unit Back Panel11”8”Remote Hub Unit Front PanelRF In RF OutAlarmOptical In/OutOptical InOptical OutCellular Antennas2”Litenna™ Base UnitFiberopticTx #1FiberopticTx #8FiberopticRx #1FiberopticRx #8Down LinkUp LinkRF Out(Sector 1)RF Out(Sector 2 Opt.)RF In(Sector 1)RF In(Sector 2 Opt.)Litenna™ Block DiagramLitenna™ RHU #8FiberopticRx #8FiberopticTx #8HPALNAFilters & DiplexersRFRFLitenna™ RHU #1FiberopticRx #1FiberopticTx #1HPALNAFilters & DiplexersRFRF

Navigation menu