Controlled Entry Distributors 433TSPW2KC ENTRY REMOTE CONTROL User Manual IS TM243CCUK

Controlled Entry Distributors, Inc. ENTRY REMOTE CONTROL IS TM243CCUK

User Manual

1A - General informationThe Community Controls - Monarch 433TSPW2KC is a 2 buttons key chain style mini transmitter operating at 433,92 MHz. It has been designed for the control of automatic closing systems and anti-burglar systems, thanks to its very high security coding system (KeeLoq® Hopping code). The code sent by the transmitter changes at each activation, avoiding any scanning and copying risk. A special algorithm allows to keep transmitterCONTENTS1A - General information1B - Technical specifications1C - Main components1 - TRANSMITTER OVERVIEW2 - NUMBERING3 - PROGRAMMING4 - OPERATION5 - BATTERY ACCESS1B - Technical specificationsOperating frequency 433,92 MHzNumber of keys: 2 Battery : 2 x 3V lithium batteries CR2016Battery life: 18 ÷ 24 monthsSecurity code: Keeloq® Hopping codeNumber combinations : 2exp64Operating temperature: -20°F÷+131°F (-20°C÷+55°C)Overall dimensions: 2.4”x1.4”x0.51” (61x36x13 mm)Weight: 0.49 oz. (14 gr.)synchronized transmitter and receiver. The transmitter can operate with many receivers of the range Community Controls - 433R. Ask your installer or reseller the product which best fits your application. The output of the receivers can be either wiegand 26 bit ( to communicate with access control systems ) or 1-2-4 relay with NO - NO/NC output. The CR 2016 lithium batteries of the transmitter have a shelf life of about 6 months. The product fully complies with Part 15 of FCC Regulations and the European Directives 1C - Main componentsRed LEDKey holder ring Dark redpush-button6 - TROUBLESHOOTINGManualMONARCH 433TSPW2KCDark grey caseFig. 2Thank you for choosing a Community Controls product .Please read this manual carefully before using the product.Made in Italy. Copyright © 2004 by Community ControlsCommunityControls
IS-TM243CCUK Rev. 0 del 05.03.2013Community Controls - Type : 433TSPW2KCFCC ID : SU7433TSPW2KC2 - NUMBERINGTo access the battery open the case with a screwdriver acting on the slot between the cover and the bottom and remove the bottom, as shown in fig. 3a and 3b. Slide out the old batteries and replace them with the new ones [CR2016] respecting the polarity, with the positive (+) side upward. NOTE: Please dispose of the batteries properly according to local laws and regulations. Test proper battery installation by verifying that the LED illuminates when the button is pushed.5 - BATTERY ACCESS3 - PROGRAMMINGEach transmitter is manufactured and sold with a different factory-set serial number .The transmitter must be programmed into your system memory. Your own installer or reseller will provide you the necessary instructions for your system.4 - OPERATIONA - Firmly depress the button until the small red LED illuminates.B - After the LED has illuminated, release the button. If the device you are attempting to activate does not respond, repeat steps A and B or consult section 7 ( Troubleshooting ) of this manual.Fig. 3aFig. 3b6 - BATTERY STATUSLed GREEN Normal level ~6000 pulses [*] - Normal range Led ORANGE Attention level Max 300 pulses - Low range[*]Led RED Low level Replace battery - No rangeLed color Battery level TX StatusThe warranty period of Community Controls 433 transmitters is 24 months, beginning from the manufacturing date of the transmitter. During this period, if the product does operate correctly, due to a defective component, the product will be repaired or replaced at the sole discretion of Community Controls. The warranty does not extend to the transmitter case which can be damaged by conditions outside the control of Community Controls or to battery life.WARRANTYThis device complies with FCC Rules Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation.Part. 15 of the NoticeAny changes or modification to equipment not expressly approved by could void the manufacturer’s warranty.Community ControlsCommunity ControlsThe system does not receive the transmitter signal.The transmitter LED is ONCheck to verify the transmitter is programmed into your systemPROBLEM SOLUTIONThe operating range is reduced Replace the transmitter batteries7 - TROUBLESHOOTING[ * ] : Depends on batteries type and operating conditions . Batteries life calculated with 1-sec pulses.2500 South 3850 West, Suite A - Salt Lake City, Utah 84120www.communitycontrols.com - sales@communitycontrols.com

Navigation menu