Controlled Entry Distributors 318LIPW2KC ENTRY REMOTE CONTROL User Manual IS TM23DCCUK
Controlled Entry Distributors, Inc. ENTRY REMOTE CONTROL IS TM23DCCUK
UserManual.wiki
>
Controlled Entry Distributors
>
318LIPW2KC User Manual
User Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![2 - NUMBERINGTo access the battery open the case with a screwdriver acting on the slot between the cover and the bottom and remove the bottom, as shown in fig. 3a and 3b. Slide out the old batteries and replace them with the new ones [CR2016] respecting the polarity, with the positive (+) side upward. NOTE: Please dispose of the batteries properly according to local laws and regulations. Test proper battery installation by verifying that the LED illuminates when the button is pushed.5 - BATTERY ACCESS3 - PROGRAMMINGEach transmitter is manufactured and sold with a different factory-set serial number .The transmitter must be programmed into your system memory. Your own installer or reseller will provide you the necessary instructions for your system.4 - OPERATIONA - Firmly depress the button until the small red LED illuminates.B - After the LED has illuminated, release the button. If the device you are attempting to activate does not respond, repeat steps A and B or consult section 7 ( Troubleshooting ) of this manual.Fig. 3aFig. 3b6 - BATTERY STATUSLed GREEN Normal level ~6000 pulses [*] - Normal range Led ORANGE Attention level Max 300 pulses - Low range[*]Led RED Low level Replace battery - No rangeLed color Battery level TX StatusThe warranty period of Community Controls 318 transmitters is 24 months, beginning from the manufacturing date of the transmitter. During this period, if the product does operate correctly, due to a defective component, the product will be repaired or replaced at the sole discretion of Community Controls. The warranty does not extend to the transmitter case which can be damaged by conditions outside the control of Community Controls or to battery life.WARRANTYThis device complies with FCC Rules Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation.Part. 15 of the NoticeAny changes or modification to equipment not expressly approved by could void the manufacturer’s warranty.Community ControlsCommunity ControlsThe system does not receive the transmitter signal.The transmitter LED is ONCheck to verify the transmitter is programmed into your systemPROBLEM SOLUTIONThe operating range is reduced Replace the transmitter batteries7 - TROUBLESHOOTING[ * ] : Depends on batteries type and operating conditions . Batteries life calculated with 1-sec pulses.2500 South 3850 West, Suite A - Salt Lake City, Utah 84120www.communitycontrols.com - sales@communitycontrols.comCommunity Controls - Type : 318DOPW2KCFCC ID : SU7318LIPW2KCIS-TM23DTSUK Rev. 0 del 21.02.2013](https://usermanual.wiki/Controlled-Entry-Distributors/318LIPW2KC/User-Guide-2103408-Page-2.png)
![2 - NUMBERINGTo access the battery open the case with a screwdriver acting on the slot between the cover and the bottom and remove the bottom, as shown in fig. 3a and 3b. Slide out the old batteries and replace them with the new ones [CR2016] respecting the polarity, with the positive (+) side upward. NOTE: Please dispose of the batteries properly according to local laws and regulations. Test proper battery installation by verifying that the LED illuminates when the button is pushed.5 - BATTERY ACCESS3 - PROGRAMMINGEach transmitter is manufactured and sold with a different factory-set serial number .The transmitter must be programmed into your system memory. Your own installer or reseller will provide you the necessary instructions for your system.4 - OPERATIONA - Firmly depress the button until the small red LED illuminates.B - After the LED has illuminated, release the button. If the device you are attempting to activate does not respond, repeat steps A and B or consult section 7 ( Troubleshooting ) of this manual.Fig. 3aFig. 3b6 - BATTERY STATUSLed GREEN Normal level ~6000 pulses [*] - Normal range Led ORANGE Attention level Max 300 pulses - Low range[*]Led RED Low level Replace battery - No rangeLed color Battery level TX StatusThe warranty period of Community Controls 318 transmitters is 24 months, beginning from the manufacturing date of the transmitter. During this period, if the product does operate correctly, due to a defective component, the product will be repaired or replaced at the sole discretion of Community Controls. The warranty does not extend to the transmitter case which can be damaged by conditions outside the control of Community Controls or to battery life.WARRANTYThis device complies with FCC Rules Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation.Part. 15 of the NoticeAny changes or modification to equipment not expressly approved by could void the manufacturer’s warranty.Community ControlsCommunity ControlsThe system does not receive the transmitter signal.The transmitter LED is ONCheck to verify the transmitter is programmed into your systemPROBLEM SOLUTIONThe operating range is reduced Replace the transmitter batteries7 - TROUBLESHOOTING[ * ] : Depends on batteries type and operating conditions . Batteries life calculated with 1-sec pulses.2500 South 3850 West, Suite A - Salt Lake City, Utah 84120www.communitycontrols.com - sales@communitycontrols.comCommunity Controls - Type : 318LIPW2KCFCC ID : SU7318LIPW2KCIS-TM23LCCUK Rev. 0 del 05.03.2013](https://usermanual.wiki/Controlled-Entry-Distributors/318LIPW2KC/User-Guide-2103408-Page-4.png)