ConnecteDevice BT3A Bluetooth Headset User Manual

ConnecteDevice Limited Bluetooth Headset

Users Manual

PAGE 1 / 6 BLUETREK E2 user guide (Same operation G2+, G3n, X2-2, Y2-2 and S22) Thank you for choosing the BLUETREK® E2, we hope you will enjoy the convenience we are bringing to you. The BLUETREK® E2 offers many functions, please read this manual before getting started. EC-Declaration of Conformity We, Innovi Technologies Ltd of Suite 501-3, 5/F., Chinachem Leighton Plaza, 29 Leighton Road, Causeway Bay, Hong Kong. declare under our sole responsibility that our product BLUETREK E2 to which this declaration refers is in conformity with the appropriate standards EN300 328-02 EN301 489-17 EN301 489-01 EN50371 EN60950 Following the provisions of Radio and Telecommunications Terminal Equipment directive 1999/5/EC. September 2005 Guillaume Ponticelli, Director of Development
PAGE 2 / 6 FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications to this Bluetooth® headset not expressly approved by the party responsible for compliance could void the user’s authority to operate it. Industry Canada notice to users and product statements To prevent radio interference with the licensed service, this device is intended for operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. In compliance with Industry Canada regulations, technical specifications have been provided in a declaration of conformity. This does not imply that Industry Canada approved the equipment. Bluetooth® is a trademark owned by Bluetooth SIG, Inc. and is used by the manufacturer under license.
PAGE 3 / 6 BEFORE USING YOUR HEADSET FOR THE FIRST TIME - You must charge it continuously for about 8 hours, until the red indicator light turns off. Please refer to the “Charging the BLUETREK® E2” section of this manual. - Pair the headset with a mobile phone. Please refer to the “Pairing BLUETREK® E2” section of this manual. Introduction The BLUETREK® E2 headset is a wireless headset based on the Bluetooth® technology. The BLUETREK® E2 headset has 3 buttons: • “TALK “button (main button), • 1 “VOL+ “button, • 1 “VOL- “button. Charging the BLUETREK® E2 Please connect the charger to the headset and to the mains. During the charge, the indicator light is red during a normal charge. The indicator light will turn off when the charge is complete. During subsequent charges, the charging should take approximately 2 hour 40 minutes. When the indicator light flashes in red, your headset needs to be recharged. Important: • The headset cannot be operated while charging. To maximize battery capacity, it is recommended to recharge your headset to full capacity only when the battery is low, since a battery has a lifetime of about 500 charging cycles. • If you leave your headset battery empty for an extended period of time, it could excessively discharge the battery. In this case, you may have to charge your headset for 10 hours or more until the battery recovers and recharges completely. • Only switch on the headset once the red indicator light turns off, indicating the battery has fully recovered. • Do not let the battery charger remain plugged in the headset for more than 24h. • The use of any other charger will automatically suspend the warranty. Pairing the BLUETREK® E2 Before using the BLUETREK® E2 headset, you must pair it with your Bluetooth® mobile phone. Pairing is the process of linking 2 Bluetooth® devices, so that they can communicate. To initiate pairing:
PAGE 4 / 6 1. Place the BLUETREK® E2 and your mobile phone within 0.3 meter (1 foot) from each other. 2. Switch on your phone and select its Bluetooth® discover mode (refer to the Bluetooth® mobile phone user manual). 3. When the BLUETREK® E2 is switched off, press and hold the TALK button for about 7 seconds until the indicator light flashes red and blue alternatively. And a sound can be heard in the speaker. 4. Once the mobile phone detects the headset, a “BLUETREK E2” message will be displayed. Follow the phone instructions to accept the pairing. The PIN code (or passkey) is 0000, then press “yes” or “ok”. If pairing was successful, the indicator light will switch to blue and flashes slowly. If you haven’t started the discovery mode within 5 minutes, the headset will switch off. You must then switch on your headset and start the pairing again. Wearing the BLUETREK® E2 For your convenience, the ear clamp of BLUETREK E2 is designed to be adjustable and removable which allows the headset to be worn on either ear comfortably. BLUETREK® E2, as packaged, is ready to be worn on your right ear. For left ear, simply unsnap the ear clamp from the headset by pulling gently at the base of the ear clamp ring. Flip the ear clamp over, and snap it back onto the headset by applying gentle pressure on the base of the ear clamp ring. Make sure the speaker is properly inserted into your ear. Switching the BLUETREK® E2 ON and OFF Switching BLUETREK® E2 ON When your headset is off, press and hold the TALK button for about 2 seconds until the blue indicator light is on. A beep (2 tones) can be heard in the speaker. Release the TALK Button. To check if your headset is ON, press once on the TALK button. If the indicator light flashes blue, it means your headset is ON. Switching BLUETREK® E2 OFF When your headset is on, press and hold the TALK button for about 5 seconds until the red indicator light is on after the quick blue flashes. A beep (2 tones) can be heard in the speaker then release the TALK Button. Making a call Mobile phone with voice recognition . Make sure the voice recognition function on your mobile is activated and your voice tags have been recorded with the phone. To enter these, please refer to your phone’s manual . When there is no incoming or active call, press once on the TALK button . Wait for the audio signal sent by the mobile phone (generally a short tone). . Speak the name of person you wish to call.
PAGE 5 / 6 Mobile without voice recognition . Make sure both the headset and the mobile phone are ON and in stand-by mode. . Dial the number on the phone keypad, after approximately 2 seconds the audio connection will be established. This function may not be available on some phones, please refer to the trouble shooting frequent asked questions in our website: www.bluetrek.com. to find out more. Answering a call When the headset rings, press once on the TALK button to take the call. Ending a call Press once on the TALK button to end an active call. Adjusting the volume To increase the volume during an active call, press the “VOL+” button on the headset. To decrease the volume during an active call, press the “VOL-“ button on the headset. Muting the microphone To mute the microphone during an active call During an active call, press and hold the VOL+ button for approximately 2 seconds. A periodic tone can be heard in the speaker when the microphone is muted. To end the mute function When the microphone is muted quickly press the VOL+ button on the BLUETREK® E2. The periodic tone will end. Transferring a call from BLUETREK® E2 to the mobile phone During an active call, press the TALK button for about 2 seconds. (This function only works in the Hands-Free Profile.) In the Headset profile, you can simply turn off your headset. Transferring a call from the mobile phone to the BLUETREK® E2 During an active call on the mobile phone, press the TALK button for approximately 2 seconds until you hear the beep. Call waiting When you hear a call waiting alert while you are on a call, press once on the TALK button to accept the second call. This function may not be available, depending on your phone’s functionality. However, you can always answer the second call from your phone keypad. Multi Pairing BLUETREK® E2 can be paired to two mobile phones. For instance :
PAGE 6 / 6 Your headset is already paired with mobile phone A. You then perform a pairing with mobile phone B. All incoming calls on mobile phone A or B can be answered by BLUETREK® E2 as long as the headset is on standby. However, you can only use mobile phone B (i.e. the lastly paired phone) for outgoing calls. Note: This function is not available on some phones. Please refer to the trouble shooting frequent asked questions in our website: www.bluetrek.com. to find out more. Additional features with some phones Rejecting a call When the headset rings, press the TALK button for about 2 seconds. Redial the last number When there is no incoming or active call, press the TALK button for about 2 seconds until you hear a beep. Troubleshooting guide The first thing you should do when encountering a problem that you cannot solve with this manual, is to switch off your headset and your mobile phone, and switch them on again. To find out more, please refer to the trouble shooting frequent asked questions in our website: www.bluetrek.com. An automatic reset is done each time the headset is either charged or switched off. So in case of problem or if your headset cannot switch off, please charge your headset for at least 30 seconds. Guidelines for safe use Read those guidelines before using your headset. - Do not drop or try to alter the shape of your Headset. - Do not expose your headset to liquid or moisture. - Do not expose your headset to extreme temperatures. Temperature range : 0-40C. - Do not expose your headset to fire or open flames. - Do not try to disassemble your headset. Service and Maintenance can only be performed by authorized BLUETREK dealers. - Keep your headset away from dust and dirt. - Do not let children play with your headset, since it contains small parts that could become detached and create a choking hazard. - Check the regulation in your area if you plan to use your headset while driving. - Turn off your headset before boarding an airplane. CAUTION : Danger of explosion if battery is incorrectly replaced. Dispose of batteries according to local regulations. Do not dispose as household waste.

Navigation menu