Compex Systems WPJ428 Wireless Access Point User Manual WPJ428 rev1

Compex Systems Pte Ltd Wireless Access Point WPJ428 rev1

UserManual.wiki >

Compex Systems >

WPJ428 User Manual >

WPJ428_User Manual rev1

Contents

1. WPJ428-User Manual v2 2017-07-18
2. WPJ428_User Manual rev1

WPJ428_User Manual rev1

wireless embedded boardsLast Updated: 22/05/2017Multi-function IPQ4028 Embedded Board with on-board Wireless710MHz CPU / 2x GE Port / Dual Band 802.11ac Wave 2SpecicationsChipset CPU: Qualcomm Atheros IPQ4028 710MHzReference Design DK03System Memory 256MB DDR3NOR Flash 32MBNAND Flash 128MBWireless On-board 2x2 2.4GHz 802.11b/g/nOn-board 2x2 5GHz 802.11a/n/ac4x U.FL connectors Frequency Range 2.412~2.462GHz, 5.180~5.320GHz, 5.500~5.720GHz, 5.745~5.825GHzModulation Techniques OFDM: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAMInterface 2x Gigabit Ethernet LAN RJ45 Port with Auto MDI-X1x M.2 (NGFF) “B Key” Socket for 4G Module (Note1)1x USB 3.0 PortReset Button 1x F/W Reset ButtonLED 7x LED Indicators for MMZ/MMS/MPSPower over Ethernet Passive PoE 24V, for network cable length < 20m (LV version),IEEE 802.3af/at or Passive PoE 48V (HV version)DC Power 1x DC Jack Connector: 24V (LV version), 48V (HV version)Power Consumption (Board Only) 19WOperating Voltage 3.3V, 5VOperating System Compex OSCertiﬁcation RoHS ComplianceEnvironmental Temperature: Operating: -20ºC to 70ºC, Storage: -40ºC to 90ºCHumidity (non-condensing): Operating: 5% to 95%, Storage: Max. 90%Dimensions (W x H x D) 117 x 105 x 32 mmExtras 2 x SIM Card Slots (Note2)1 x BuzzerOther Features Surge SuppressorModel: WHV1PJ428KEY FEATURES• Qualcomm Atheros IPQ4028 Quad-core ARM cortex-A7 710MHz CPU• 2x2 On-board 5GHz radio, up to 867Mbps physical data rate• 2x2 On-board 2.4GHz radio, up to 300Mbps physical data rateAPPLICATIONS• 802.11n/ac Access Point• Point-to-Point High Capacity Wireless RouterCOMPEX SYSTEMS PRELIMINARYNote1: The configuration is not applicable for this FCC applicant.FCC ID: TK4WPJ428 Note2: The configuration is not applicable for this FCC applicant.

Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. 70Caution： This device is only defined as point-to-point product by the manufacturer.

Navigation menu