Compex Systems MMN344VX Wireless Access Point User Manual MMN344LV A rev3

Compex Systems Pte Ltd Wireless Access Point MMN344LV A rev3

UserManual.wiki >

Compex Systems >

MMN344VX User Manual

MMN344LV-A_User Manual rev3

indoor access pointLast Updated: 30/03/16Specications Chipset Board CPU: Qualcomm Atheros AR9344 560MHz (2.4GHz)Radio Card: Qualcomm Atheros QCA9882 (5GHz)System Memory 128MB DDR2NOR Flash 16MBAntenna 2.4GHz: 2x External 2dBi Rubber Duck Omni antenna5GHz: 2x External 2dBi Rubber Duck Omni antennaInterface 2x Gigabit Ethernet Port (Auto MDI-X)1x JTAG 14 Pin Connector11x Serial Port 4 Pin Connector1Reset Button YesLED Indicators: Power LED, LAN Activity, 4x Signal IndicatorDC PowerPower Consumption 10.5W (Max)Operating System Compex OSRoHS Compliance YesEnvironmental Temperature: Operating: -20ºC to 70ºC, Storage: -40ºC to 90ºCHumidity (non-condensing): Operating: 5% to 95%, Storage: Max. 90%Dimensions 129 x 129 x 51 mmOther Features Surge Suppressor, Watchdog Timer1. These features can only be accessed on the Embedded Board.KEY FEATURES• Qualcomm Atheros 560MHz Processor AR9344• IEEE 802.11ac/a/b/g/n compliant • 2.4GHz and 5GHz concurrent radios• 2.4GHz 24dBm and 5GHz 24dBm aggregate power• Data rates of up to 867Mbps in 802.11ac 80MHz channels• Enhanced sensitivity performance• 2x External 2dBi 2.4GHz Rubber Duck Omni Antennas• 2x External 2dBi 5GHz Rubber Duck Omni Antennas• Antenna Alignment LEDsSupport wall mountingAPPLICATIONS• Dual Band concurrent 802.11ac + 802.11b/g/n Access Point • Single Band 802.11ac/a or 802.11b/g/n Access Point•Dual Band 2x2 MIMO 802.11ac/a/b/g/n Versatile Indoor Access Point560MHz CPU / 2.4GHz 300Mbps / 5GHz 867MbpsMIMO New Series 1x DC Jack Connector: 12-24V (LV version)• Model: MMN344LV-A

Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter.

Navigation menu