ColorMaker T10 Transmitter User Manual PX T10Manual indd

ColorMaker, Inc. Transmitter PX T10Manual indd

User Manual

IntroductionThe PX-T10 is the most advanced wireless LED controller on the market today. The PX-T10 design is an accumulation of years of research and development by ColorMaker inc. The PX-T10 is a microprocessor based system that can be updated by the user as new software is developed. The hardware was designed with more memory and features we could ever use so we are only limited by our imagination. This manual was written by the PX-T10 software developers at ColorMaker. We have tried to explain the numerous features the PX-T10 has to offer in the simplest terms possible. We understand the user will not think like a software developer and understand our technical language so we have 9am to 9pm technical support for the confused user. We have take thousands of technical calls and have a good understanding where users are most confused and have tried to explain less technical terms in this manual. All we ask is that you take the time to read and the rest will fall into place with a few phone calls. The PX-T10 basic functions can be learned in a just a few easy steps and will cover lessons in this manual. The more complicated features can be mastered is just under an hour. As always we have 9am to 9pm technical support (407) 862-3363 and 24/7 email support Jerry@ColorMaker.net. The lessons in this manual have been written to provide the user with start up information to get up and running is just a few minutes. We will then take you into the fi xture color editing with the various functions and discuss how each function will work. This will be followed by scene control and we will teach you how to record and play scenes. The fi nal lesson will be using the ColorRoll features and how it will senselessly integrate into the controls. Below is a list of new features that will be covered in detail in this manual1) Group Control2) Master Dimmer Controls3) Full ON/OFF Buttons4) 10 Color Presets5) ColorRoll STOP6) F Save7) SFCP (Single Fixture Color Programming)8) Display in Percent or DMX9) Battery Level Monitor
Keypad buttons and FunctionsThe PX-T10 has 30 buttons to control up to 90 individual fi xtures. Each button was graphically designed to represent a function. Some button functions will change when used with multi button press such as the shift button. All these functions will be covered in detail later in this manual and followed by lessons and procedures.Master controlThis is the UP and Down control of the master dimmer. When pressed all fi xtures on the remote network address will be dimmed by the setting from 0 to 100%. When dimmer is not at 100% (Full ON) the LED indicator marked Master will light.RGB controlsThis is the UP and Down control for the RGB (Red, Green and Blue) color settings. These will also be used when a ColorRoll is active to adjust the Roll, Rate and Flash controls of the ColorRollFull ButtonThis is a one of the multi button controls. When pressed with the RGB controls the current color will advance to full on or full off. Preset ButtonThis is another multi button control. When pressed with the Q1 through Q10 buttons the color in the circle will be the preset color that will be sent to the controls.Fixture Select buttons are multi function buttons. The will be used to select a fi xture, Change networks and select a color preset. ColorRoll Select buttons. These will also be used to make changes to the PX-T10 function controls.ColorRoll Stop will be used to terminate a ColorRoll and a single channel. This is also a control button to set the LED display to read out in Decimal (DMX) or Percentage 0%-100%.Go Button used to execute a group control feature. This will also be used to display PX-T10 battery power level.Play Button use to play a sceneRecord Button used to record a scene. This will also be used to command all fi xtures to store its current color into memory.SFCP (Single Fixture ColorRoll Programming) This is a multi button control. When pressed along with the Q1 through Q10 this will also the user to program ColorRolls using a single fi xture. This will also be used to restore the PX-T10 to default factory settings.Shift Button used to select multi function controlsBlackout used to turn all fi xtures OFF1
2Display FeaturesThe PX-T10 has 4 LED indicators, 3 digit display and an RGB color simulator to assist the user in remote navigation. These indicators will be explained in more details in this manual as we guild you through each of the features. The 4 LED indicators each with a single word to illustrate what they will identify during programming. Here is a brief description:Master indicator will light when master value is below 100%.ColorRoll indicator will light when the RGB Up and DN buttons are for editing the ColorRoll Rate, Follow and Flash values.ALL indicator will light when Q10 (ALL) button was pressed to target all fi xtures on the current network.Group indicator will light when the user has preselected a group of fi xtures for editing. RGB Color Simulator is the larger LED just to the left of the 3 digit display. This will emit the same color as the current fi xture that is being edited. This is useful during programming and allow the user to make changes to fi xture color without needing a fi xture to visually see the colors. 3 Digit LED Display is a numeric display that will also show alpha characters to guild the user in programming.Display Power Down is a battery save feature that will turn off the display after 10 minutes of non use. By pressing any button the display will activate.
3
4PX-T10 Fade, Beep, Display SetupThe PX-T10 can be setup to each users needs with custom cross fade and dimmer speed controls. These custom options are programed through the keypad with just a few simple steps. Once programmed the options setting are saved to memory and are recalled each time the PX-T10 is turned on. The options can also be set back to factory defaults if needed. Below is a table of the custom settings and a description of there features.The options are accessed by pressing and hold the SHIFT button and then pressing the function button. The fi rst press will give the current setting and additional presses will change to next options. The shift key must be held for options to change. The 3 Digit display will identify each action. The option values can be reset to factory defaults by pressing and holding the SFCP (clear) button while turning on the PX-T10. Function control Options Options (factory default=*)Shift + ColorRoll 1 Cross fade: This controls the how fast each scene will cross fade when played.Hi *LowOFFShift + ColorRoll 2 Dimmer Speed: This values sets the speed of the RGB dimmer controlsHi *LowShift + ColorRoll 3 Beep Control: ON *OFFShift + Roll Stop Display value: Displays value in percent (0-100) or DMX (0-255)“d” DMX“P” Percent *Shift + GO Displays battery power level Power remainingFixture RGB Controls IntroductionThe PX-T10 can control up to 90 individual fi xtures which means each of the 90 fi xtures under the control of the PX-T10 can be doing something different whether its a static color or running a ColorRoll. The PX-T10 processor will store all the changes made to each of the 90 fi xtures in an internal buffer then recall the information when the user returns to the fi xture for editing. The RGB Color Simulator will glow the fi xtures color along with the displays 3 digit value. ColorRoll fade rates are also recalled so the user can return to a fi xture and edit the roll rates without having to resend the ColorRoll pattern. ColorRoll indicators will light to identify the selected fi xture is running a ColorRoll pattern.There are 5 ways to control the 10 fi xtures on each network. The functions are for static colors only ColorRolls will be covered later.RGB Level ControlsUser selects a fi xture, Group or ALL function then edits color with RGB UP/DN buttons. By pressing and holding the Full buttons the selected color will jump to full ON or Full OFF. Play SceneWhen a scene is played the current 10 fi xtures will cross fade to the next scene played.ALL ControlBy Selecting ALL (SHIFT + Q10) all 10 fi xtures will follow the commands presented. All indicator will also light.Group ControlUser selects only the fi xtures that he wants to take control then presses GO. Group indicator will also light.Color PresetsUser selects a fi xture, Group or ALL function then selects a Color Preset. The selected fi xtures will change to the selected preset. The user also has control of cross fade control of color presets.
5Getting StartedThe PX-T10 has been pre programmed at the factory with default settings and is ready for use out of the box. All fi xtures are also factory programmed with default address channel 1 and will not require setup to use. To get started turn on your ColorMaker fi xture and the PX-T10 remote. Once the display reads F-1 you can used the Red, Green and Blue Up and Down buttons to change the fi xture color. By mixing the RGB with different intensity levels you can generate up to 16 million colors. Fixture default channel is number 1 so all fi xtures will be controlled using Q1 on the PX-T10. The ColorMaker line of wireless LED fi xtures have an Auto Address feature that automatically sets the fi xture address by simply pressing a few buttons. The ColorMaker LED fi xture will have a blue auto address button with an LED indicator next to it. Auto AddressingSetting Fixtures to operate on different channels just follow these 3 steps. Step 1) Power up the fi xture then press and Hold the auto address button until the indicator light shows orange which will take 1-2 seconds. Step 2) Press one of the Q buttons on the PX-T10 you want the fi xture to be programmed. Step 3) Press the Red UP button to send the command. The fi xture will now follow any command you send while on the selected Q. Follow these same 3 steps for all fi xtures. The next lesson will take you through editing 10 fi xtures each on a different Q so if you have 10 fi xtures auto address each one to Q1 through Q10. Lesson 1: Editing 10 fi xtures This lesson with guide you through the steps to edit 10 fi xtures each with a static color using the RGB UP/DN dimmer controls. Step 1) Turn on your PX-T10 and press the Blackout button. This will turn all fi xtures OFF if not already and will clear the PX-T10 buffer so all RGB levels are at 00. Step 2) Now lets target fi xture 1 by pressing the Q1 button. We will make this fi xture red by pressing and holding the Red UP button until the display reads 100. You will also see the RGB color simulator start to glow red to refl ect the changes make to Q1. Step 3) Now lets target fi xture 2 by pressing the Q2 button. We will make this fi xture Green by pressing and holding the Green UP button until the display reads 100. You will also see the RGB color simulator start to glow Green to refl ect the changes make to Q2. Step 4) Now lets target fi xture 3 by pressing the Q3 button. We will make this fi xture Blue by pressing and holding the Blue UP button until the display reads 100. You will also see the RGB color simulator start to glow Blue to refl ect the changes make to Q3. Step 5) Now lets target fi xture 4 by pressing the Q4 button. We will make this fi xture Purple by pressing and holding the Blue UP button until the display reads 100 then the Blue UP button until the display reads 100. You will also see the RGB color simulator mix the Red and Blue colors to emit a purple. Step 6) Now you should have 4 fi xtures 1 red, 2 green, 3 blue and 4 purple. The PX-10 has an internal buffer that will remember what color value each of the Q’s has been changed and when returning to the Q to make changes the information will also be displayed for reference. Press Q1 and you will see the RGB Color simulator change to red and the display will also be updated to the dimmer values for additional editing. Press each of the Q’s to get familiar with the response. Step 7) Now lets target fi xture 5 by pressing the Q5 button. We will make this fi xture 100% Red. You can use the Red UP button and scroll 0 through 100 or Press and Hold the Full button then press the Red UP. The Full button will advance the color to Full ON when UP is pressed or Full OFF when DN is pressed. This is just a short cut for quick editing. This should give you an understanding of the RGB dimmer controls. Lets move on to some other controls that will be handy.
6Lesson 1: Editing 10 fi xtures (continued)We have covered the basics on editing colors on each Q using the RGB dimmer controls. The PX-T10 has another shortcut for quick editing called the “ALL” button which is also the Q10 button. The ALL or (Shift + Q10) function select all 10 fi xtures at one time to change the colors. The All command works well when the fi xtures are all the same color prior to the command. If you have already setup your fi xtures with different colors use the Group and GO command for better results. Step 8) Lets blackout all the fi xtures before we begin. Press the blackout button and all fi xtures will go off and clear the PX-T10 buffer. To activate the ALL function Press and Hold the Shift button and then press Q10 or All button. The display will read “ALL” and the ALL indicator will light. Adjust any of the RGB dimmers and you will see all 10 fi xtures will follow the commands. To exit all command just press any of the Q buttons and the PX-T10 will return to single Q edit. Controlling Fixtures with Color Presets.The PX-T10 has 10 Color Presets which can be used to quickly change the selected fi xture color. The color preset buttons are also shared by the Q buttons. Preset colors are in the upper right corner of the button with the colored circle that will represent the button preset color. The preset colors can be user programed to a desired color if the factory default color is not acceptable. Programming color preset will be covered later in this manual. Color Preset Fade OptionsWhen using the Color Preset the user has the option on how the color preset are transmitted to the fi xture. The setting are Fade or OFF. This option is selected by (Shift + Color Preset button) Fade means the selected color preset will fade from the current fi xture color to the selected preset color. OFF means the selected Preset color is instantly change without Fade. Step 9) Lets blackout all the fi xtures before we begin. Press the blackout button and all fi xtures will go off and clear the PX-T10 buffer. Lets select fi xture 1 by pressing Q1 button. Now lets send color Preset 1 or RED to the fi xture by pressing and holding the Color Preset button then press Color Preset 1 or Q1. Fixture 1 will then change to RED. This procedure can be used for all fi xture and with any color preset. Controlling Fixtures with Group and GOPX-T10 can edit a group of selected fi xtures with a function called Group and GO. The user can select any or all fi xtures and command only those selected to change. The user can control how the new color will be displayed on the fi xture when the GO command is given. The options are Hi, Low and OFF which are Cross fade time in the setup commands. There are 3 steps to the Group and GO command. 1) select the group, 2) select the color and 3) execute the GO. Let give it a try it will be more clear one you have completed the steps. Step 10) Lets blackout all the fi xtures before we begin. Press the blackout button and all fi xtures will go off and clear the PX-T10 buffer. Let target Fixture 1 and Fixture 4 and send Green to them. To setup the Group command press and Hold the GO button and them press and release Q1 and press and release Q4. The group indicator will light to show you have entered a Group and GO command. Now release the GO button this tells the PX-T10 you have fi nished selecting the fi xtures in the group and will now choose a color. Press and hold the Green UP until the you reach 100% or you can use the Full button for faster response. At this point you have selected the group, chosen a color and all that is left is to execute the command. Press GO! Fixture 1 and 4 should now be green. Group and go color selection can also be done with Color Presets so instead of Green UP you can Press and Hold the Color Preset button and choose a color preset. All the changes made to the fi xtures are also stored in the PX-T10 buffer so you can return after a Group and GO command and edit any of the 10 fi xtures with any of the function commands.
7Controlling Fixtures with Group and GO (continued)Lets cover one last Group and GO feature before we move on. This time we will target 2 fi xtures with different colors and you will see a nice cross fade to the selected Group and GO color. Step 11) Lets blackout all the fi xtures before we begin. Press the blackout button and all fi xtures will go off and clear the PX-T10 buffer. Now set Fixture 1 through fi xture 10 to different colors. I will leave this entirely up to you just be sure then all are different. Not to worry you have 16 million colors to choose from. Now we want to be sure your Group and GO is set to cross fade so you will see how this works. To edit the Cross fade setup value Press and Hold the Shift button then press and release the ColorRoll 1 which is also the Cross Fade setup button. As we previously discussed the fi rst press and release displays the current value and additional presses will make changes. For the demo we want the setting to be HI so adjust accordingly.Step 12) Hopefully at this point you have fi xture 1,2 and 3 to different colors. We will now change them to Blue and you will see how they go from multi color to all blue with a nice cross fade. Lets execute the Group and GO command by Press and Hold the GO button then press and lease Q1, Q2 and Q3. Release the GO button press the Blue UP button until it reaches 100%. Now press the GO, you will see a nice cross fade from multi color fi xtures to all blue. That wraps up Group and GO, Practice mixing up the functions of RGB Dimmer control, Color Presets and Group and GO your next event will be amazing. Controlling Fixtures with ScenesThe PX-T10 has 10 programmable scene buttons that will store the RGB values of all 10 fi xtures. The scenes are controlled with the Q1 through Q10 and will use the Play and Rec buttons to execute and save. When a scene is played the user has the option to setup how fast the scene will fade. Lets say you have 10 fi xtures all set to green and the scene you are about to play is all red. If you want the fi xtures to instantly turn to red we will use the cross fade setting of OFF, if you want the fi xture to slowly go from green to red we will use the setting of Low and last setting is Hi which will cross fade faster rate. This cross fade value is setup by using the Shift + ColorRoll 1 as previously discussed. Lets fi rst record a simple red, green blue scene using 3 fi xtures. Set fi xture 1 to red, fi xture 2 to green and fi xture 3 to blue all others will be off for now. To record this scene press the Rec button and the display will read “rec” to identify the PX-T10 is ready to record a scene. Now press the scene button you want to store the scene we will use Q1 for this demo so press Q1. Lets test your fi rst scene. Press the blackout button to turn off all fi xtures and then to play the scene press Play and then Q1. You will notice 3 fi xtures with the colors red, green and blue and depending on our cross fade setting they may have instantly fl ashed to the new colors or a slow cross fade. The PX-T10 controls the cross fade time and the display will read “FAd” until the cross fade has completed. While cross fade is running the PX-T10 will not accept any command from the keypad.Master Dimmer ControlThe PX-T10 and PX series LED fi xtures have a new Master control. This will dim all fi xtures on all 9 network channels. When the PX-T10 master is not at full the Master indicator will light to let the user know the Master is not at 100 %. Master dimmer works on all fi xtures in static color and running ColorRoll patterns. The PX-T10 can be turned off during an event if needed and when turned back on the Master control will load last dimmer setting to resume control. User has an option to include all network addresses or select only 3. This option is set by Shift + Master UP an DN. The minimum value is 3 which will set N1, N2 and N3 to be included in the master controls. The maximum is 9 which will set all 9 network addresses to master control. There is a trade off in performance when all 9 network addresses are set so the default is 5. When this option is above 5 then the master dim time is increased which can slow the rate of dim. This can be tested with a fi xture or watch the 3 digit display during master UP and DN control.
PX-T10 ColorRoll TechnologyWhat is ColorRoll ?“ColorRoll is a technology developed by ColorMaker inc to operate on the ColorMaker line of wireless LED fi xtures. When activated a collection of colors are transmitted to the fi xture by a remote. This is an endless loop when the last color is reached the process starts over to the fi rst color. Once the ColorRoll has started the Fade Time from color to color can be controlled The fi xture will operate completely independent of the transmitter until it receives a signal to terminate. Custom colors are programmed and saved in the remote. There are 3 buttons marked ColorRoll 1, ColorRoll 2 and ColorRoll 3 which are used for the ColorRoll feature”This was our fi rst description when we fi rst developed the technology. If you have used ColorMaker products in the past you will have the basic understanding of ColorRolls. We have enhanced the ColorRoll features in the PX-T10 and PX Series fi xtures for better controls and integration into your event. There are still 10 colors in the pattern, there are still controls for the fade, follow and fl ash controls and there are still 3 ColorRoll buttons for programming. Below is a list of the new features which we will take you through in the next lesson. 1) We have added a ColorRoll STOP button to terminate a ColorRoll. This is not just a Stop button it will also command the fi xture to return to the static color it was displaying before the ColorRoll command. 2) We have added ColorRoll Rate editing. When a ColorRoll command is given to a fi xture the user can return to the same fi xture at any time to edit the rate, follow, and fl ash values while the fi xture continues its ColorRoll. The PX-T10 will identify the selected fi xture is running a ColorRoll with a ColorRoll indicator and load the previous rate values for editing. These new features will enable the user to add ColorRolls to there event seamless. ColorRolls can be executed and terminated without the need for a blackout. Sending a ColorRoll to a fi xtureColorRolls are executed by selecting a fi xture and then pressing 1 of the 3 ColorRoll buttons. The “Rec” buttons is used to record and ColorRoll but the Play button is not used to start a ColorRoll. This has been a confusing part for most of our users in the past so I wanted to clear this up for you. Let me take you through the steps to send a ColorRoll. There are factory programmed ColorRoll patterns in all 3 buttons so we can send those for this demo. Be sure the indicator light on the ColorMaker fi xture is set to RED to enable the ColorRoll feature.(See fi xtures user’s manual for more information on this option)Step 1) Select fi xture 1 by pressing Q1Step 2) Press ColorRoll 1 button to send the ColorRoll pattern to the fi xture.The fi xture will start its ColorRoll and the PX-T10 ColorRoll indicator will light letting you know the RGB UP/DN buttons are now to control the ColorRoll Rate, Follow and Flash controls. The Red value will control the fade rate or how fast the colors will fade the higher the values the slower the rate, The Green value will control the Follow time, this is the time each color will pause and the Blue value will control Flash or Fade. If the value is below 50% the colors will fade and if the value is above 50% the colors will fl ash. 8
ColorRoll NavigationThe PX-T10 new ColorRoll features will track which fi xtures are running a ColorRoll and which ones have a static color. This will enable the user to mix up the event with a colorful atmosphere. When a Q is selected the PX-T10 will identify the Q is running a ColorRoll by lighting the ColorRoll indicator and the user will know the RGB UP/DN buttons are for editing the ColorRoll Rate, Follow and Flash values. If the Q is pressed and the ColorRoll indicator does not light then the Q is a static color and the RGB UP/DN buttons are for color editing. ColorRoll (mixing it up)There is one last feature we have added that will enhance your event. Our software developers thought this was a cool idea so they added it. In a nutshell each Q has a little memory space that will hold 3 values. So we decided to use this space to hold ColorRoll Rate, Follow and Flash values that will be unique to any ColorRoll running on the selected Q. When you select Q1 and send ColorRoll 1 you can edit the rate of the ColorRoll. This rate is then stored in this memory space. Then you can select Q2 and send the same ColorRoll 1 pattern and edit. Even though you have sent the same ColorRoll to Q1 and Q2 they will have there own unique roll rates. Let me give you an example and why our software developers thought this was a cool idea. Example:You have 10 fi xtures and you use the (Shift + Q10) ALL function to target all fi xtures. You then select ColorRoll 1 and all fi xtures start running the ColorRoll. The new PX series ColorRoll patterns are synchronized so all 10 fi xtures will roll at the same rate. Well that’s sounds boring, so you select Q1 and edit the roll rate then select Q2 and edit the roll rate. Well now you have 2 fi xtures running the same ColorRoll 1 pattern but with different roll rates. You can do this for all 10 fi xtures for some cool effects. ColorRoll STOPColorRoll Stop function will terminate a ColorRoll pattern on a selected Q and return the fi xture to the color it was displaying before the ColorRoll was executed. This will enable the user to start and stop ColorRolls during an event without the need to hit the blackout. Lets do a short lesson on ColorRoll Stop. Step 1) Set fi xture 1,2 and 3 to blue. Step 2) Select Q1 and press ColorRoll 1. Step 3) Select Q2 and press ColorRoll 1. You should now have 2 fi xtures with ColorRolls and 1 with static color Blue. Step 4) Select Q1 and press ColorRoll Stop. Fixture 1 will then terminate ColorRoll and return to static color Blue. Step 5) Select Q2 and press ColorRoll Stop. Fixture 2 will then terminate ColorRoll and return to static color Blue. You will also see the RGB color simulator on the PX-T10 will show Q1, Q2 and Q3 all set to blue. How Cool!9
Programming a ColorRollA ColorRoll pattern is a collection of up to 10 colors that the user can create using the 10 Q buttons on the PX-T10 with each Q being a separate color for example Q1 is the fi rst color in the pattern and Q2 with be the second color all the way to Q10 which will be the last color. A ColorRoll does not require all 10 colors to be set if you only want to do a 3 color pattern which we will explain in our next lesson. The ColorRoll properties such as Fade Rate, Follow Rate and Flash are not part of the programming steps but can be set after the user records the pattern to the ColorRoll button. There are several ways to program a ColorRoll the lessons we have done up till now have used 10 fi xtures with each fi xture set to Q1 through Q10 so we will use all 10 in the fi rst lesson. Step 1) Lets fi rst press the Blackout button to turn off all fi xtures and clear the PX-T10 buffer. The buffer will hold the ColorRoll pattern while we create it. Step 2) Press the Q1 button and set to full Red. This is our 1st color in the patternStep 3) Press the Q2 button and set to full Green. This is our 2nd color in the patternStep 4) Press the Q3 button and set to full Blue. This is our 3rd color in the patternStep 5) Set Q4 through Q10 to colors of your choosing.Step 6) Now that you have all 10 Q’s set we will program this fi rst pattern to ColorRoll 1. Press and release the Rec button and when the display reads “Rec” press ColorRoll 1. The pattern is now saved to ColorRoll 1. While you were programming each Q the fi xtures also displayed the colors in the pattern. You also had the RGB color simulator to reference which assist you in programming. Step 7) Lets test the new ColorRoll pattern. Press Q1 as we will target fi xture 1 to run the ColorRoll. Now press ColorRoll 1 and the fi xture should run the pattern if programmed properly. When a new ColorRoll pattern is programmed the Rate, Follow and Flash are all reset to 0 so you should have a fast rolling ColorRoll pattern. ColorRoll Programming SFCP (Single Fixture Color Programming)The PX-T10 has a new SFCP button which can be used to direct all Q’s being programmed to show up on fi xture set to Q1. This will not affect how the PX-T10 will save the pattern it only tells the PX-T10 to send the color to fi xture 1 when the user selects the SFCP button. The SFCP is only active when the user PRESS and HOLD the SFCP button while selecting the Q button. ColorRoll Programming (remove the dead spot)Lets go over the ColorRoll pattern some more to explain ColorRoll patterns. The fi rst lesson we programmed a ColorRoll pattern with 10 colors. The pattern rolled from the fi rst color to the last then repeated. Lets say you only wanted 2 colors and want the fi xture to fade Red to Blue then repeat. This is possible but if you program Q1 to Red and Q2 to blue and Q3 through Q10 to OFF the fi xture will think Q3 is part of the ColorRoll program and will roll Red, Blue to OFF then repeat. To avoid the OFF or dead space fi ll the rest of the ColorRoll pattern to the same color as your last color in your pattern in this case Blue. Below are 2 examples. Example 1 includes an OFF in the ColorRoll and Example 2 removes the OFF. 10Example 2: ColorRoll process that starts with Red then fades to Blue then repeats.Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10Example 1: ColorRoll process that starts with Red then fades to Blue then fades OFF then repeats.Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10
11ColorMaker is dedicated to the on going development of our wireless technology. The PX-T10 can be upgraded as we develop new features to store Scene and ColorRolls.The PX-T10 communicates over 916 MHz which will not be affected by wireless microphones, speakers and most DJ equipment. WarrantyColorMaker hereby warrants, to the original purchaser, ColorMaker products to be free of manufacturing defects in materials and workmanship for a period of 1 year from the date of purchase. This warranty shall be valid only if product is purchased within the United States of America. It is the owners responsibility to establish the date and place of purchase by accepting evidence, at the time service is sought.For warranty service, send the product to the ColorMaker factory. All shipping charges must be prepaid. Equipment must be sent in its original package and to include all control devices.Warrant is void if serial number has been altered or removed, seals have been voided, if the product is modifi ed in any manner which ColorMaker concludes, after inspection, affects the reliability of the product; if the product has been repaired or services by anyone other than ColorMaker unless prior written authorization was issued to purchaser.ColorMaker reserves the right to make any changes in the designs and/or improvements upon its products without any obligation to include these changes in any products theretofore manufacture.Factory location:ColorMaker 980 Sunshine Lane Suite TAltamonte Springs Florida 32714(407) 862-3363
12This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:* Reorient or relocate the receiving antenna.* Increase the separation between the equipment and receiver.* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.* Consult the dealer or an experienced radio/TV technician for help.The user is cautioned that changes and modifi cations made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.

Navigation menu