Cobra Electronics XRSR7-MDU RF LINK w/ RADAR DETECTOR User Manual

Cobra Electronics Corporation RF LINK w/ RADAR DETECTOR

UserManual.wiki >

Cobra Electronics >

XRSR7-MDU User Manual >

Contents

1. USERS MANUAL
2. users manual

users manual

XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:14 PM Page FC1FOURTH DRAFT

Important Information and Customer AssistanceIntroductionImportant Information •Federal Laws Governing the Use of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra®radar/laserdetector. The Communications Act of 1924 guarantees your right to receive radiotransmissions on any frequency. Local laws that contravene this Act, while illegal, maybe enforced by your local law enforcement officials until and unless they are prohibitedfrom doing so by federal court action.Safety/Strobe AlertUse of this product is not intended to, and does not, ensure that motorists orpassengers will not be involved in traffic accidents. It is only intended to alert themotorist that an emergency vehicle equipped with a Cobra Safety Alert, 3M or Tomarstrobe transmitter is within range as defined by that product. Please call local fire andpolice departments to learn if coverage exists in your area.Some states and municipalities prohibit mounting any object on your windshield. If youdrive in these states or areas; you can mount the MDU on the dash.Safe Driving Motorists are expected to exercise all due caution while using this product, and to obeyall applicable traffic laws. Security of Your Vehicle Before leaving your vehicle, always remember to conceal your Remote Display Unit(RDU) in order to reduce the possibility of break-in and theft. Your Main Detector Unit(MDU) has a two-position bracket that, when in the up position, presents a very discreetprofile from outside the vehicle.Customer Assistance •Use your owner’s manual to learn about product features. Cobra Electronics offers thefollowing customer assistance services:For Assistance in the U.S.A. Automated Help Desk, English only. 24 hours a day, 7 days a week 773-889-3087.Customer Assistance Operators, English and Spanish, 8:00 am to 6:00 p.m. CentralTime Mon. through Fri. (except holidays) 773-889-3087.Questions, English and Spanish, Fax: 773-622-2269.Technical Assistance, English only, www.cobra.com. English and Spanish e-mail, Product info@cobra.com.For Assistance Outside the U.S.A. Contact Your Local Dealer©2007 Cobra Electronics Corporation™6500 West Cortland StreetChicago, Illinois 60707 USAwww.cobra.comCustomer AssistanceA1 EnglishXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:14 PM Page A1FOURTH DRAFT

THISSURFACETOWARDSSKYControls, Indicators and ConnectionsIntroductionA2 EnglishIntelliLink™Remote Display Unit (RDU)Full-ColorExtreme BrightDataGrafix™DisplayGlobal Positioning System Locator(GPSL)USB Connector 12-Volt Power ConnectorMDU ConnectorPower &PairingButtonTwo-Piece, Self-AdhesiveFastenersMain Detector Unit (MDU)SpeakerOptional GPSL for Model XRS R7 and Standard on Model XRS R9GGPSL CableThe XRS R7 provides detection capabilities for radar, laser and strobe signals.The XRS R9G has all the features of the XRS R7 plus a GPSL module withalerts when approaching photo-enforced intersections and roads with fixedred light/speed cameras. The XRS R9G can store up to 1,000 additional userprogrammable Location Alerts.GPSL ConnectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:14 PM Page A2FOURTH DRAFT

IntroductionNothing Comes Close to a Cobra®A3In This Package12-Foot Power Cord - Fuse Box 12-Foot Power Cord - Accessory PlugIn This Package •USB/USB Mini Retractable CableRDU Holster and Vent/Visor Clips GPSL Cable (R9G Only)12V-5V USB Power AdapterMDU Power Cord Clips20 clips and 20 adhesive squaresTwo Hoop Loop Strips for MountingHolsterXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:14 PM Page A3FOURTH DRAFT

ContentsIntroductionNothing Comes Close to a Cobra®1IntroductionImportant Information . . . . . . . . . .A1Customer Assistance . . . . . . . . . . .A1Controls, Indicators and Connections . . . . . . . . . . . . . . . .A2In This Package . . . . . . . . . . . . . . .A3Product Overview . . . . . . . . . . . . . . .2Installation Overview . . . . . . . . . . . .4Your DetectorInstallation . . . . . . . . . . . . . . . . . . . .6Controls and Display . . . . . . . . . . .15Getting Started . . . . . . . . . . . . . . . .17EasySet Programming . . . . . . . . . .21Program Navigation . . . . . . . . . . . .22Settings . . . . . . . . . . . . . . . . . . . . .24Detection Alerts . . . . . . . . . . . . . . .29Radar and Laser . . . . . . . . . . . . . . .32Maintenance . . . . . . . . . . . . . . . . . .35Specifications . . . . . . . . . . . . . . . . .36WarrantyWarranty . . . . . . . . . . . . . . . . . . . . .37User LicenseUser License . . . . . . . . . . . . . . . . . .39Customer AssistanceProduct Service . . . . . . . . . . . . . . .41Trademark Acknowledgement . . . .42Optional Accessories . . . . . . . . . . .43Accessories Order Info . . . . . . . . . .44XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:14 PM Page 1FOURTH DRAFT

Product OverviewIntroductionNothing Comes Close to a Cobra®3Remote Display Unit (RDU)The RDU is a wireless remote controller/display module that shows alertsdetected by the MDU. The RDU display uses an Extreme Bright DataGrafix™(Organic Light Emitting Diode) Display to show large graphical alerts assignals are detected.The RDU uses a rechargeable lithium-ion (LiON) battery and is supplied witha holster and clips for mounting on heating/air conditioner vents or visor.Power cables and other adapters are supplied for charging this battery usingthe vehicle 12V vehicle power with accessory adaptor plug or via a PC USBport.The normal Auto Dark screen is dark with a moving dot. The Auto Darkscreen provides discreet usage and helps conserve RDU battery life. Thedisplay color can be changed to match most dash illumination.Global Positioning System Locator (GPSL) - (XRS R9G Only)The GPSL module tracks vehicle location. It uses a database that alerts as itapproaches photo-enforced intersections and roads with fixed red light/speedcameras.Use the GPSL functions to program alerts and store up to 1,000 userprogrammable Location Alerts. Software will be available to update thedatabase and stay current with future hazards and warning locations. TheGPSL module has no external controls and connects to the MDU with onecable.Registering Your DetectorTo register Cobra XRS R7 or XRS R9G go to www.cobra.com. Click on theProduct Registration tab.XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:14 PM Page 3FOURTH DRAFT

4EnglishInstallation OverviewMount UnitMain Detector Unit (MDU)Note: To power the MDU, use one of the two power cords provided(See Page A3).•12-Foot Power Cord – Acessory Plug: For connecton to 12-voltvehicle accessory outlet, or•12-Foot Power Cord – Fuse Box: For connection to vehicle’s fusebox using the in-line fuse and wires.Fuse box hard wiring is recommended. Use this configuration toprovide a more discreet installation. If you are unsure about makingthis connection yourself, contact a professional installer.On a negative grounded vehicle:1. Connect the positive wire [marked with a tag (+)] of the DC power cordto an accessory 12-volt fuse that is controlled by the ignition switch(Figure A).2. Connect negitive wire (-) to a chassis ground location (Figure A). Bodypaint may may need to be removed to assure a good groundconnection. IntroductionACCFigure AXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:14 PM Page 4FOURTH DRAFT

Installation OverviewNothing Comes Close to a Cobra®5Mount MDU high on windshield to right of rear view mirror (Figure B). MDUmust have clear view through windshield and parallel to the road (Figure C)and have clearance to snap into the “up” position.Position MDU for easy access to power switch, cable connections and formirror movement. Mount the MDU on the windshield close to the headliner.IMPORTANT: Do not block the MDU lens with the sun-shaded area of thewindshield (Figure D) or the rear view mirror.Dash mounting results in decreased performance. Heated windshieldscurrently available on some vehicles (Instaclear for Ford, Electriclear for GM),may block or weaken incoming signals. Consult your automobilemanufacturer.IntroductionFigure B Figure CTHISSURFACETOWARDSSKYFigure DExternal ViewXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:14 PM Page 5FOURTH DRAFT

InstallationYour Detector6EnglishGlobal Positioning System Locator (GPSL) - (XRS R9G Model Only)Mount GPSL module close enough to the MDU for supplied cable to connectboth modules (Figure E). Mount GPSL with proper side (“This SurfaceToward Sky” wording embossed in unit case) attached to windshield andexposed to the sky.IMPORTANT: Some states and municipalities prohibit mounting any object onthe windshield. If you drive in these states or areas, mount the MDU on thedash (Figure F).IMPORTANT: Both the MDU and GPSL units will need to be flipped upside-down compared to a dashboard installation. Pay special attention tomount GPSL unit with proper side (“This Surface Toward Sky” wordingembossed in unit case) towards the sky.Figure EInternal ViewFigure FInternal ViewXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:14 PM Page 6FOURTH DRAFT

InstallationYour DetectorNothing Comes Close to a Cobra®71. Position MDU before actualmount.• Do not attempt to adjustMDU bracket.• Hold unit in place. • Using non-permanentpen, mark two oppositecorners.2. Peel off film from two-piecefastener strips. Align withtwo corner markings madein step 1. Press MDUbracket against windshield.• Fastener strips cannoteasily be removed.Strength of adhesivestrips increases withtime.• Do not pull on MDU forfirst 20 minutes.Main Detector Unit (MDU)XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 7FOURTH DRAFT

Installation8English3. Loosen MDU (gray) bracketadjust knob. Adjust moduleto a position parallel to theroad. Tighten knob to setproper detection position.The MDU mounting brackethas two detent positions:• one for detectionoperation (horizontalposition)• one for storage orconcealment (upposition). Makes MDUless visible from outside.IMPORTANT:MDU will not provide radardetection in“Stored/Concealed”position. Your DetectorNot In Use.Stored/Concealed Position.Detection PositionLower toOperatingDetectionPosition.BracketAdjust KnobXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 8FOURTH DRAFT

4. Attach power cord to MDU.Use power cord clips toroute to fuse box orlighter/accessory outlet,depending on the selectedpower cord. Surfaces mustbe clean and free of dirt, oil and dust. Plug in thepower cord.Nothing Comes Close to a Cobra®9InstallationYour DetectorInternal ViewXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 9FOURTH DRAFT

10 EnglishInstallationYour DetectorBattery ChargingThe unit is shipped with a sealed lithium-ion (LiON) batery pack that isrechargeable.IMPORTANT: Avoid temperature extremes (hot and/or cold) to help prolongbattery life and performance. DO NOT leave RDU exposed to direct sunlight. Ifthe RDU is mounted on vent, clip must be on lower fin to avoid hot airblowing on RDU battery compartment.NOTE: When battery begins to discharge too quickly, it is time toinstall a new battery.1. Turn RDU over and slidebattery cover off of RDUbody.2. Carefully plug battery wireconnector into the batteryconnection port in RDU.Connector only fits one way.3. Replace battery cover.Remote Display Unit (RDU) •Battery InstallationXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 10FOURTH DRAFT

Nothing Comes Close to a Cobra®11InstallationYour Detector1. Attach 12-volt – 5-voltretractable USB powercable to bottom of RDUand to 12-volt power adapter.2. Connect 12-volt poweradapter to vehicleaccessory outlet.3. Initial charge for battery istwo (2) hours.WARNINGThis lithium-ion (LiON) battery should only be recharged inside theRDU. Do not substitute any other type of charging adapter or chargingbase to charge the battery. Battery damage, fire or explosion may result.NOTE: Lithium-ion (LiON) batteries are toxic. Please dispose of properly.Some municipal waste disposal agencies have special provisions forbattery disposal.NOTE: After battery is fully charged, unit can be operated withoutretractable power cord until battery needs recharging.XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 11FOURTH DRAFT

12 EnglishInstallationYour DetectorRDU HolsterA holster is provided to allow you to position the RDU for best drivervisibility, access and while charging battery. A vent or visor clip will attach torear of holster for easy removable mounting locations. Two self adhesivehook loop strips are also included for more permanent mounting mostanywhere on the vehicle dashboard.Visor ClipVent ClipHook Loop StripsXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 12FOURTH DRAFT

Nothing Comes Close to a Cobra®131. Position GPSL before actualmount.• Hold GPSL unit in placewith USB cableconnected to MDU. • Using non-permanent pen, mark two oppositecorners.2. Peel off film from two-piecefastener strips. Align withtwo corner markings madein step 1. Press GPSLbracket against windshield.• Fastener strips cannoteasily be removed.Strength of adhesivestrips increases withtime.• Do not pull on GPSL forfirst 20 minutes.THISSURFACETOWARDSSKY3. Connect cable betweenMDU and GPSL.IMPORTANT: Proper side ofGPSL module (“This SurfaceToward Sky” wordingembossed in unit case) mustbe against windshield and facesky. Global Positioning System Locator (GPSL)(XRS Model R9G Only) •InstallationYour DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:42 PM Page 13FOURTH DRAFT

Introduction14 EnglishInstallationGPSL Initial Satellite Lock •The GPSL module now needs to be linked to a satellite.NOTE: This procedure may need to be repeated if the unit has not beenused after prolonged non-usage.1. With vehicle running andparked in an area clear ofobstructions to the sky, turnOn radar detector.2. Keep the unit turned on forat least 15 minutes. Thiswill allow fast satelliteacquistion in subsequentpower-ups GPSL IconXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:42 PM Page 14FOURTH DRAFT

Nothing Comes Close to a Cobra®15Controls and DisplayDIM/ButtonPress for display brightness. Navigates Program Screens.Adjusts volume in Menu mode.Adjusts volume DOWNin Volume mode.MUTE/ButtonPress for Standby Status Screens.Mutes an alert. CITY/ButtonToggle betweenHighway and Citymodes. Navigates MenuScreens.Adjusts volume UP inVolume mode.MENU/SAVE ButtonPress to enter Menuscreen.POWER/VOLUME ButtonA two second press andrelease turns unit on or off.Release for Standby Screenor Volume Screen.A momentary press forVolume screen.RDU ControlsYour DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 15FOURTH DRAFT

16 EnglishControls and DisplayThe RDU linkindicators show thethe MDU is connectedto the RDU by thewireless link. The indicator changesto show a lostconnection.The IntelliMutesymbol showsactivated feature.Changes to indicateif above or belowSet-point whenIntelliMute isturned on.(Refer to page 24.)RDU DisplayStandby ScreenWhen arrow displays,you can go to theStandby Controlscreens by pushingMUTE/ button.RDU battery icondisplays chargecondition of RDUbattery. Sections changeto display battery level.City/Highway symbolchanges to indicateactivated alert filteringmode.GPSL icon indicatesGPS satellite lock.Icon changes toindicate lost signalcondition.*Compass indicator usesGPSL to indicate directiontraveling. Indicator changeswith vehicle direction.**Note: Compass and GPSL icons only display if GPSL module isconnected (optional for XRS R7, standard on XRS R9G).Your DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 16FOURTH DRAFT

Nothing Comes Close to a Cobra®17Getting StartedPower On/Off •1. Press power button on RDU.2. Unit cycles through poweron/self test. DisplaysStandby screen whenprocess completed.3. Display changes to AutoDark operating screen after30 seconds (factorydefault). Can be changed to“Always On,” but willreduce battery On time. 4. Press, hold power buttonon RDU for more than twoseconds to turn off unit.Your DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 17FOURTH DRAFT

18 EnglishGetting StartedPress Mute/while the Standby screen displays to show Standby screenmenus.Standby ScreenStandby screen displays information about detector: alertfiltering, automatic muting functions and RDU batterystatus. If GPSL is connected, compass heading and GPSstatus icon also display.RDU BatteryRDU Battery screen displays status of RDU battery.Indicates charge left in battery or if it is plugged intopower source and is charging.I-Mute/City or Hwy ModeI-Mute screen displays status of alert filtering (City orHighway modes) and automatic muting (IntelliMute)functions. Refer to related sections to set these features.Car VoltageCar Voltage screen displays voltage level of car battery. Ifbattery voltage drops below 11.9 volts, an alert sounds.Low Car Voltage feature in Alert Settings programmingmust be activated.Standby Screen Menus •I-MUTE CITYThese screens display in this order when navigating Standby screen.StandbyScreenRDUBatteryI-MuteCity/Hwy ModeCarVoltageLat/Lon Speed CompassCompass, Speed and Latitude/Longitude screens only display if GPSL is connected to system.NOTE: Last Standby screen viewed will be one displayed when exitingAuto Dark mode.Your DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 18FOURTH DRAFT

Nothing Comes Close to a Cobra®19Getting StartedScreens display only if GPSL is connected.CompassIndicates driving direction.SpeedIndicates the GPSL system is tracking speed. Lat/LonDisplays latitude and longitude of present location. CompassNWSpeed55mphLat / Lon41º54'53"N87º47'22"WYour DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 19FOURTH DRAFT

20 EnglishGetting StartedYour DetectorMuting Alerts •Manual MutePress MUTE/button momentarily to turn off Audio Alert during an Alertcondition. Press MUTE/button again during alert to turn on Audio Alert.After current alert is gone, detector will un-mute and next alert sounds.Auto Dark •When Auto Dark screen is engaged, a small dot displaysat bottom of screen to show that power is on. Touch anybutton to recall Standby screen.Highway/City Mode •IntelliShield®Tri-level City mode has a Highway mode and three City modelevels: City X, City X Beep Off and City X+K.IntelliShield®Tri-Level City ModeToggle from Highway to City mode for three levels ofAudio Alert suppression. Factory setting is City X.City X sounds a single beep when X band signal is firstdetected. The alert sounds when signal strength reacheslevel 3. City X+K combines City X mode with delay of K bandaudio alerts until signal strength reaches level 2.City X Beep Off blocks all X band audio alerts until signalstrength reaches level 3. To change setting, navigate to the City Default screen.Press Mute/button to cycle through options untilsetting to change displays. Press MENU/SAVE button tosave select and return to Standby screen.XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 20FOURTH DRAFT

Nothing Comes Close to a Cobra®21Programming Overview •Begin all programming or setup with MENU/SAVE button.Select this to change USER or ALERT settings. USERsettings customize how system handles alert filtering,audio-related options, visual options and system-relatedoptions. ALERT settings determine which ALERT typesare activated. ALERT settings on the XRS R9G modelincludes GPS-related features.Press MENU/SAVE button again to save feature andfunction changes and return to Standby screen. If abutton is not pressed within 15 seconds while inSetup/Programming mode, Standby screen displays andsettings made up to this point are saved automatically.NOTE: You can restore factory settings at any time.Enter USER or ALERT settings sub-menu and displayshows left arrow , down arrow and right arrow.Arrows correspond with arrows on DIM, MUTE and CITYbuttons on RDU.Press left arrow to return to previous screen. Pressright arrow to access next screen. Press down arrowto make change. Press MENU/SAVE button to exitsetup program and save new settings. If a button is notpressed within 15 seconds while in Setup/Programmingmode, Standby screen displays and settings made up tothis point are saved.Each of these functions and settings are explained inSETTINGS section of this manual.NOTE: Advancing at the end of menu returns to beginning of menu.NOTE: Setup/Programming mode cannot be accessed during an alert.Unit does not detect signals while in Setup/Programming mode.EasySet ProgrammingUser SettingsAlert SettingsYour DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 21FOURTH DRAFT

22 EnglishCity DefaultRestoreFactory SettingsIntelliMuteAutoMuteVoice/ToneRDUBeepsDisplayColorDisplay Set-upSmartPowerSpeedUnitsPairRemoteNOTE: Only shown if RDU lock is lost.NOTE: Only shown when GPSL is installed.User SettingsProgram NavigationYour DetectorProgram Flow Diagrams •User Settings DiagramScreens display in this order when navigating through User Settings menu.Speed Units screen displays only if GPSL is connected to system. Pair RDUscreen displays only if system detects a missing RDU connection.XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 22FOURTH DRAFT

Nothing Comes Close to a Cobra®23Alert Settings DiagramScreens display in this order when navigating through Alert Settings menu.Speed Alert, Display GPS Db Date and Delete ALL User Locations screensdisplay only if a GPSL is connected to system.POP X Band K Band KU BandDeleteAll UserLocationsDisplayGPSDbSpeedAlertLow CarVoltageThese screens display only if GPSL is connected.VG-2 SpectreSafetyAlertAlert SettingsProgram NavigationYour DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 23FOURTH DRAFT

24 EnglishSettingsYour DetectorProgramming User Settings •IntelliMute®ModeSet IntelliMute to mute alerts when vehicle is stopped ormoving slowly. Intellimute senses engine RPMs andmutes alerts. IntelliMute does not mute strobe signalsfrom emergency vehicles. IntelliMute works with City andAuto Mute modes.Set an RPM activation point to start IntelliMute.IntelliMute begins muting alerts when engine RPMs fallbelow set RPMs. The activation point is stored inmemory and recalled each time the power is turned on.IntelliMute is factory set off.An IntelliMute icon appears in display when IntelliMute ison and activation is set. When engine RPMs fall belowthe activation point, Arrow points down. Arrow points upwhen engine RPMs are above the activation point. If unitstops sensing the engine’s RPMs, IntelliMute indicates anerror and automatically turns off. When initially choosing your IntelliMute activation point, asetting approximately 300 to 600 RPMs above idle isrecommended. Reset the activation point at any time to fitindividual preferences and driving style.NOTE: Reset RPM point if detector is used in a different vehicle.IntelliMute may not work with some vehicles because it cannot sensethe engine’s RPMs. Reduce unwanted audio alerts by using Auto MuteIntelliShield®Tri-level and City Mode.WARNINGDO NOT attempt to set the RPM point while driving. Your vehicle shouldbe parked and idling to avoid a collision during the process.XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 24FOURTH DRAFT

Nothing Comes Close to a Cobra®25SettingsYour DetectorSetting IntelliMuteFrom the IntelliMute Setup screen:1. Press MUTE/button to start setup.2. Press and hold the vehicle accelerator at desired engine RPMs.3. Press DIM/button to complete setting process.System stores engine RPM setting and displays a completion message and atone or voice message. Unit must sense a usable pulse within three secondsor a set RPM point within 30 seconds of beginning of setup, or IntelliMutedetects an error and turns off. Change a set activation point by accessing Set IntelliMute in User SettingsProgramming. Repeat three-step setup process above. Auto Mute ModeAuto Mute reduces audio volume of all alerts after four seconds. Alertsremain muted as long as signal is detected. Alerts sound at full volume aslong as signal is detected when Auto Mute is off. Auto Mute factory setting ison. Press the MUTE/from the Auto Mute screen to change the setting. Voice or Tone ModeSet detector to sound alerts and confirm program settings with a Voice or aTone. Voice Alert provides voice messages in addition to tones. Tone Alertprovides tones only. Factory setting is Voice Alert. Remote Display Unit (RDU) Beep LevelRDU Beep sets the volume level for the keypad confirmation tones of theRDU. Choose from low, high or off RDU beep level volumes. RDU Display ColorRDU screen color theme is customizable to match your personal preferenceor your vehicle’s dash illumination. Choices include Multi-Color, Red, Blue,Orange or Green. Factory setting is Multi -Color. XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 25FOURTH DRAFT

26 EnglishSettingsYour DetectorDisplay SetupDisplay Setup determines how long RDU button backlight and display stayson and delay time before RDU screen switches to Auto Dark mode. Set RDUdisplay time for 15 seconds, 30 seconds, one minute, three minutes orAlways On. Factory default is 30 seconds. NOTE: If selecting “Always On” setting, RDU battery will need chargingmore frequently.Smart Power ModeSmartPower feature turns system off five minutes after car’s engine is turnedoff. Before SmartPower engages, three beeps sound and SmartPower flasheson display. Start the car or press Power/Pairing button to return to normalpower. Factory setting is SmartPower On. Speed Units (Shown only if GPSL is connected)Displays vehicle speed in miles per hour (MPH) or kilometers per hour(km/h). Factory setting is MPH.Restore Factory SettingsRestore detector to original settings here. Confirmation messages displayduring process. XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 26FOURTH DRAFT

Nothing Comes Close to a Cobra®27SettingsProgramming Alert Settings •POP AlertWith Pop Detect mode on, signals are detected and an alert given. Duringalert unit continues to detect other signals. Factory setting is Pop Detect Off.X Band AlertWith X Band Detect mode on, signals are detected and an alert given. Duringalert unit continues to detect other signals. Factory setting is X BandDetection On.K Band AlertWith K Band Detect mode on, signals are detected and an alert given. Duringalert unit continues to detect other signals. Factory setting is K Band DetectOn.Ku Band Alert With Ku Band Detect mode on, signals are detected and an alert given. Duringalert unit continues to detect other signals. Factory setting is Ku Band DetectOff.VG-2 Alert Detector is undetectable by VG-2 detection devices. An alert is given whensuch a device is in use near the vehicle. When VG-2 Detect mode is On, VG-2signals are detected and an alert given. During alert unit continues to detectother signals. Factory setting is VG-2 Detect Off. VG-2 Audio Mode When VG-2 Audio mode is On, alerts are heard and displayed. This setting isonly available if VG-2 Alert is On. Factory setting is VG-2 Audio Off. Spectre 1 Alert Detector is undetectable by Spectre 1 detection devices. An alert is givenwhen such a device is in use near the vehicle. When Spectre 1 Detect mode isOn, Spectre 1 signals are detected and an alert given. During alert unitcontinues to detect other signals. Factory setting is Spectre 1 Detect Off. Your DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 27FOURTH DRAFT

28 EnglishSettingsSpectre 1 Audio Mode Spectre 1 Audio mode is only available if Spectre 1 Alert is on. Alerts areaudio and displayed on screen. Safety Alert radar signals are detected andalerts given when Safety Alert mode is on. Factory setting is Spectre 1 AudioOff. Safety Alert When Safety Alert mode is On, Safety Alert radar signals are detected and analert is given. During alert unit continues to detect other signals. Factorysetting is Safety Alert On. Low Car Voltage WarningMany U.S. cars have continuous power to 12V outlet and if a device isconnected/kept on, it will drain vehicle’s battery. To avoid this, XRS R7/R9Gcomes with Smart Power and Low Car Voltage Warning features.The detector emits a car battery low alert when voltage drops below 11.9volts. The detector enters SmartPower mode to avoid further battery draining.Factory setting is Car Battery Low On.The following functions are available only if a Global Positioning SystemLocator is connected to the system.Speed AlertThe Speed Alert with the GPSL module tracks vehicle speed and sounds analert when set speed is exceeded. Speed settings increase or decrease in 5 MPH or km/h increments, depending upon Speed Units chosen in UserSettings. Speed alert must be turned on to see Adjust Speed Setting screen.Factory setting is off.Display GPS Database DateThe GPS database screen is only informational. The screen changes onlywhen databases are updated.Delete all User LocationsDelete all user-programmed location alerts with this screen. Your DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 28FOURTH DRAFT

Nothing Comes Close to a Cobra®29Detection AlertsDetection Alerts •Alert ScreensAll alerts have a unique tone and a vocal alert if the VoiceAlert feature is activated.Radar AlertsRadar alerts for X band, Ku band, K band and Ka bandgenerate a screen display “RADAR,” signal type and anumber (1-5) indicating the signal strength. A uniquetone sounds with a vocal alert if the Voice Alert feature isactivated.POP, VG2 or SP1 display depending on signal typedetected.Laser AlertsLaser alerts are indicated by an “L” and laser signal type. Ka1K 1Ku1RADARRADARRADARX 1RADARPOP SP1VG2RADAR RADARRADARL20 / 20LLPRO LASER 3PRO LASERLULTRA LYTEYour DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 29FOURTH DRAFT

30 EnglishDetection AlertsEmergency Vehicle AlertsEmergency vehicle alerts are indicated by “EV” and thelabel “EMERGENCY.”Road Hazard AlertsRoad Hazard alerts show “RH” and “ROAD HAZARD.”Railroad AlertsRailroad alerts generate “RR” and “RAILROAD.”Low Car Voltage AlertThe detector emits a car battery low alert when voltagedrops below 11.9 volts. The detector enters SmartPowermode to avoid further battery draining. Factory setting isCar Battery Low Off.The following screens are shown only if a Global Positioning SystemLocator (GPSL) is connected to the system.A detector system with a GPSL also receives alerts based on vehicle locationand information in its databases.Photo Enforcement AlertsAn alert to a Photo Enforcement area is indicated by acamera surrounded by a circle. As you get closer to thelocation, the circle and the camera get progressivelylarger and you hear a unique chime. If the Voice Alert isactivated you will also hear a voice alert.EVEMERGENCYRHROAD HAZARDRRRAILROADCAR VOLTAGE LOWWARNINGYour DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 30FOURTH DRAFT

Nothing Comes Close to a Cobra®31User Location AlertsThe system can store up to 1,000 User programmableLocation Alerts set to give hazard warnings not known tothe GPSL. The screen displays a flag surrounded by acircle. When approaching a stored location, the circleand flag get progressively larger. In addition, a uniquetone sounds as vehicle approaches location. A voice alertsounds if Voice Alert is activated.NOTE: A particular User Location can be deleted only when the vehiclereturns to that location and receives a User Location Alert. PressMENU/SAVE to delete that location. A confirmation screen displays with“Yes” and “No” selections. Press “Yes” to confirm User LocationDeleted. Press “No” to cancel delete.Speed AlertsSpeed alerts are generated when the GPSL senses thevehicle is going faster than the speed settingprogrammed in the Alert Setting menu. The displayindicates actual vehicle speed and a tone sounds. Allradar, laser, strobe and safety alerts have priority andoverride this alert. Factory default is Off.Detection AlertsSpeed Alert55mphYour DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 31FOURTH DRAFT

32 EnglishRadar/Laser and GPSUnderstanding Radar and Laser •Radar Speed Monitoring SystemsFour band frequencies have been approved by the Federal CommunicationsCommission (FCC) for use by speed monitoring radar equipment:X band 10.525 GHzK band 24.150 GHzKa band 33.400 – 36.000 GHzKu band 13.435 GHzYour detector detects signals in all four radar bands.VG-2 and Spectre 1 VG-2 and Spectre 1 are “detector detectors” that work by detecting low-levelsignals emitted by most radar detectors. Your detector does not emit signalsthat can be detected by VG-2 or Spectre 1, but does detect VG-2 and Spectre 1 signals and alerts you when a device is in use near your vehicle. Safety Alert Traffic Warning SystemFCC-approved Safety Alert transmitters emit microwave radar signals thatindicate the presence of a safety-related concern. Depending on thefrequency of the signal emitted, it can indicate a speeding emergency vehicle,train or a stationary road hazard. Because these microwave signals are within the K band frequency, mostconventional radar detectors detect Safety Alert signals as standard K bandradar. Your detector, however, is designed to differentiate between standard K band and Safety Alert signals, and give separate alerts for each.Safety Alert technology is relatively new. Safety Alert transmitters can befound in limited numbers in all 50 states, but the number is growing.Depending on your location, you may not receive these alerts regularly andmay often encounter emergency vehicles, trains and road hazards withoutbeing alerted. As the number of transmitters increases, these alerts willbecome more common.When you receive such an alert, watch for emergency vehicles ahead of you,on cross streets or behind you. If you see an emergency vehicleapproaching, pull over to the right side of the road and allow it to pass.Your DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 32FOURTH DRAFT

Nothing Comes Close to a Cobra®33Radar and LaserStrobe AlertSpecial strobes mounted on the light bars of authorized emergency vehicles(fire trucks, police cars, ambulances) automatically change traffic signals asthe vehicle approaches an intersection. These strobes and the special strobedetectors located on the traffic signals are already in use in more than 1000cities nationwide. Cobra’s exclusive Strobe Alert detector detects thesespecial strobes and sounds an emergency vehicle alert.When you receive such an alert, watch for an approaching emergency vehicleand pull over to allow it to pass. Contact your local fire and policedepartments for information about coverage in your area.LIDAR (Laser)The correct name for the technology that most people refer to as “laser” isactually LIDAR, Light Detection And Ranging. LIDAR operates much likeradar. Its signal spreads out like a radar signal, though not as widely. Unlikeradar, LIDAR must have a clear line of sight to its target vehicle throughoutthe entire measurement interval. Obstructions such as sign posts, utilitypoles or tree branches prevent valid speed measurement.Some common questions about LIDAR include:IDoes weather have any affect on LIDAR?Yes.Rain, snow, smoke, fog or airborne dust particles reduce the effective range of LIDAR and can, with dense conditions, prevent itsoperation.ICan LIDAR operate through glass?Yes.Newer LIDAR guns can obtain readings through most types ofglass. However, the laser pulse also can be received through glass totrigger an alarm by your detector.ICan LIDAR operate while in motion?No.Because LIDAR operates by line of sight, the person using it cannotdrive the vehicle, aim and operate the gun all at the same time.IIs LIDAR legal to use?Yes.It is legal in all 50 states.Your DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 33FOURTH DRAFT

34 EnglishRadar and LaserPop Radar GunsThe Pop Mode Radar Gun is a single-pulse Doppler radar that is a feature ofa K and Ka (Bee III Ka radar gun) band Instant-On radar gun. It uses a single,short-time pulse to measure the target vehicle’s speed. The Pop mode receiver senses Pop signals beyond the effective range of Popradar guns. As the Pop mode receiver is so sensitive, you should limit theuse of Pop Detect mode to highway and rural driving.Your DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 34FOURTH DRAFT

Nothing Comes Close to a Cobra®35MaintenanceMaintenance •Detector is designed and built to give years of trouble-free performancewithout service. No routine maintenance is required.Follow these steps if unit is not operating properly:IMake sure power cord is properly connected.IMake sure lighter/accessory outlet of vehicle is clean and free ofcorrosion.IMake sure power cord’s accessory adapter is firmly seated inlighter/accessory outlet.ICheck power cord fuse (unscrew ribbed end cap of accessory adapterand examine fuse) or in-line fuse of cable to fuse box, depending oncord used. If required, replace with 2-amp fuse only.NOTE: Rechargeable battery packs should be recycled or disposed ofproperly in compliance with all applicable laws. Certain states ormunicipalities provide recycling and have established collectionprograms. Please contact your local waste removal authority forinstructions.WARNINGDo Not put battery packs into fire or expose to high heat. They mayexplode.WARNINGTo reduce risk of damage, use only approved battery packs.Your DetectorXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 35FOURTH DRAFT

36 EnglishSpecificationsYour DetectorBand and Frequencies •Band FrequenciesX Band 10.525 ± 0.050 GHzK Band 24.125 ± 0.125 GHzSafety Alert 24.070 ± 0.010 GHzTraffic Warning 24.110 ± 0.010 GHzSystem24.190 ± 0.010 GHz24.230 ± 0.010 GHzKa Band 34.700 ± 1.300 GHzKu Band 13.435 ± 0.050 GHzLaser 910 ± 50 nmStrobe 700 ± 300 nmThis radar detector is covered by one or more of the following U.S. patents: 5,497,148; 5,594,432;5,612,685; 6,078,279; 6,094,148; 6,621,447. Additional patents may be listed inside the product or pending. NOTE: This device complies with part 15 of FCC rules: Operation issubject to the following two conditions: (1) This device may not causeharmful interference, and (2) This device must accept any interferencereceived including interference that may cause undesired operation.XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 36FOURTH DRAFT

Nothing Comes Close to a Cobra®37WarrantyWarranty •COBRA ELECTRONICS CORPORATION warrants that its products, and thecomponent parts thereof, will be free of defects in workmanship andmaterials for a term of one year from the date of first consumer purchase.This warranty may be enforced by the first consumer purchaser, providedthat the product is used solely within the U.S.A and Canada. Cobra will, without charge, repair or replace, at its option, defective productsor component parts upon delivery to the Cobra Factory Service Department,accompanied by proof of the date of first consumer purchase, such as aduplicated copy of a sales receipt. The consumer must pay any initialshipping charges required to ship the product for warranty service. Returncharges will be at Cobra’s expense, if the product is repaired or replacedunder warranty.This warranty gives the consumer specific rights, and he or she may alsohave other rights which vary from state to state.NOTE: Cobra makes no warranty as to the accuracy or completenessof the data in the products and disclaims any and all express, impliedor statutory warranties, including any implied warranty ofmerchantability or fitness for a particular purpose.EXCLUSIONS – This limited warranty does not apply: 1. To any product damaged by accident; 2. In the event of misuse or abuse of the product or as a result ofunauthorized alterations or repairs; 3. If the serial number has been altered, defaced or removed; 4. If the owner of the product resides outside the U.S.A and Canada.WarrantyXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 37FOURTH DRAFT

38 EnglishAll implied warranties, including warranties of merchantability and fitness fora particular purpose are limited in duration to the length of this warranty.COBRA SHALL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OROTHER DAMAGES; INCLUDING, WITHOUT LIMITATION, DAMAGESRESULTING FROM LOSS OF USE OR COST OF INSTALLATION. Some statesdo not allow limitations on the duration of an implied warranty and/or do notallow the exclusion or limitation of incidental or consequential damages, sothe above limitations may not apply to some consumers.It is the user’s responsibility to use this product prudently and responsibly.This product is intended to be used only as a travel aid and must not be usedor any purpose requiring precise measurement of direction, distance, locationor topography.WarrantyWarrantyXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 38FOURTH DRAFT

Nothing Comes Close to a Cobra®39User License •This document and the software and data described in it are furnished underlicense and may be used or copied only in accordance with such license.Except as permitted by such license, the contents of this document, softwareand data may not be disclosed to third parties, copied or duplicated in anyform, in whole or in part, without the prior written permission of CobraElectronics Corporation. This document, software and DATA containproprietary and confidential information of Cobra Electronics Corporation andits licensors.Cobra grants the purchaser a limited license for use of this document,software and data incorporated in its products for personal use, and not forresale, sublicense or commercial use. By using this product, the purchaseragrees to be bound by the terms and conditions of this license agreement.The purchaser acknowledges that the content of this document, software anddata are the property of Cobra and its licensors and are protected bycopyright laws of the USA and international treaties. The purchaser agreesnot to modify, decompile, disassemble, reverse engineer or reduce to humanreadable form the software, DATA or any part thereof, nor to create derivativeworks based on the contents of the document, software or data, nor removeor obscure any copyright, trademark notice, or restrictive legend. Thepurchaser agrees not to export or re-export this document or this product toany country in violation of the export control laws of the U.S.A.The contents of this document, software and data are for informational useonly and are subject to change without notice. Cobra and its licensors intendto provide their customers the most complete and accurate location databasefor red light/speed cameras available from government and private datasources. However, all data sources have limitations and some haveinaccuracies or are incomplete to some degree. These characteristics carryover to this product as well. As such, COBRA AND ITS LICENSORS SHALLNOT BE LIABLE TO THE USER FOR ANY INCIDENTAL, CONSEQUENTIAL,SPECIAL, INDIRECT OR EXEMPLARY DAMAGES ARISING FROM THE USEOF ITS PRODUCTS. THIS PRODUCT IS PROVIDED ON AN “AS IS” AND “WITH ALL FAULTSBASIS” AND COBRA AND LICENSORS EXPRESSLY DISCLAIM ALLWARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO,THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY,QUALITY, ACCURACY, TITLE AND FITNESS FOR A PARTICULAR PURPOSE.User LicenseUser LicenseXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 39FOURTH DRAFT

40 EnglishNO ORAL OR WRITTEN ADVICE OR INFORMATION PROVIDED BY COBRAAND/OR ITS LICENSORS OR ANY OF THEIR AGENTS, EMPLOYEES ORTHIRD PARTY PROVIDERS SHALL CREATE A WARRANTY AND USER ISNOT ENTITLED TO RELY ON ANY SUCH ADVICE OR INFORMATION. THISDISCLAIMER OF WARRANTIES IS AN ESSENTIAL CONDITION OF THEAGREEMENT.Cobra encourages customers to report any errors found in our data bycontacting technical assistance (available in English and Spanish) at product info@cobra.com (e-mail), by visiting our website: www. cobra.com,or by calling customer assistance (available in English and Spanish) at 773-889-3087 between 8:00 a.m. and 6:00 p.m. Central Time, Mondaythrough Friday (except holidays).User LicenseUser LicenseXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 40FOURTH DRAFT

Nothing Comes Close to a Cobra®41Product ServiceCustomer AssistanceProduct Service •For questions about operating or installing this new Cobra product, or ifparts are missing…CALL COBRA FIRST…do not return this product to thestore.If this product should require factory service, call Cobra before sending theproduct. This will ensure the fastest turn-around time on any repair. If Cobraasks that the product be sent to its factory, the following must be furnishedto have the product serviced and returned.1. For Warranty Repair, include some form of proof-of-purchase, such as amechanical reproduction or carbon of a sales receipt. Make sure the dateof purchase and product model number is clearly readable. If the originalsare sent, they cannot be returned.2. Send the entire product.3. Enclose a description of what is happening with the product. Include atyped or clearly printed name and address of where the product is to bereturned, with phone number (required for shipment).4. Pack product securely to prevent damage in transit. If possible, use theoriginal packing material.5. Ship prepaid and insured by way of a traceable carrier such as UnitedParcel Service (UPS) or Priority Mail to avoid loss in transit to:Cobra Factory ServiceCobra Electronics Corporation6500 West Cortland StreetChicago, Illinois 60707 U.S.A.6. If the product is in warranty, upon receipt of the product, it will either berepaired or exchanged depending on the model. Please allowapproximately 3 – 4 weeks before contacting Cobra for status. If theproduct is out of warranty, a letter will automatically be sent withinformation as to the repair charge or replacement charge.For any questions, please call 773-889-3087 for assistance.XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 41FOURTH DRAFT

42 EnglishTrademark AcknowledgementCustomer AssistanceTrademark Acknowledgement •Cobra®, 6 Band®, 9 Band®, DigiView®, EasySet®, Extra Sensory Detection®,IntelliMute®, IntelliShield®, LaserEye®, Nothing Comes Close to a Cobra®,Safety Alert®Traffic Warning System, Strobe Alert®, VG-2 Alert®, XtremeRange Superheterodyne®and the snake design are registered trademarks ofCobra Electronics Corporation, USA.Cobra Electronics Corporation™, 11 Band™, 12 Band™, Extreme BrightDataGrafix™, Revolution™ Series, SmartPower™, Spectre Alert™, Super-Xtreme Range Superheterodyne™, S-XRS™, UltraBright™, and Voice Alert™are trademarks of Cobra Electronics Corporation, USA.Opticom™ is a trademark of 3M Corporation. Instaclear®for Ford is a registered trademark of Ford Motor Company, Inc. Electriclear®for GM is a registered trademark of General Motors Corporation. 20-20™ and Ultra-Lyte™ are trademarks of Laser Technology, Inc. ProLaser™ and ProLaser III™ are trademarks of Kustom Signals, Inc. Bee III™ and Pop™ are trademarks of MPH Industries. Spectre™ is a trademark of Stalcar. Interceptor VG-2™ is a trademark of TechniSonic Industries LTD. Tomar®is a registered trademark of TOMAR Electronics, Inc.XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:15 PM Page 42FOURTH DRAFT

Nothing Comes Close to a Cobra®43Dual Port Power AdapterIncludes adjustable plug (up to 90˚)and fuseItem #CLP-2BTHISSURFACETOWARDSSKYGPS Locator (w/cable) Upgrade Kit(for Model XRS R7 Only) Item #RDA GPSLOptional AccessoriesCustomer AssistanceLiON Replacement BatteryItem #RDA LIBPXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:42 PM Page 43FOURTH DRAFT

Nothing Comes Close to a Cobra®44Accessories Order InfoCustomer AssistanceOrdering From U.S.A.Call 773-889-3087 for pricing or visit www.cobra.com.For Credit Card OrdersCall 773-889-3087 [Press one from the main menu] 8:00 a.m. to 6:00 p.m. Central Time,Monday through Friday.Make Check or Money Order Payable ToCobra Electronics, Attn: Accessories Dept., 6500 West Cortland Street, Chicago, IL 60707 U.S.A.To Order OnlinePlease visit our website: www.cobra.comItem # DescriptionCLP-2B Dual Port Power AdapterRDA GPSL GPS Locator (w/cable) Upgrade Kit (for Model XRS R7 Only)RDA LIBP LiON Replacement BatteryXRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:14 PM Page 44FOURTH DRAFT

Nothing Comes Close to a Cobra®EnglishFor more information or to order any of our products, please visit our website:www.cobra.comCB RadiosmicroTALK®RadiosRadar/Laser Detectors Safety Alert®Traffic Warning SystemsHandheld GPS ReceiversMobile GPS Navigation SystemsHighGear®Accessories CobraMarine®VHF Marine Radios CobraMarine®ChartplottersPower InvertersAccessories The Cobra line of quality products includes:XRS_R7_R9G_1-5-07.qxd:Layout 1 1/9/07 5:14 PM Page BC1FOURTH DRAFT

Navigation menu