Cisco Systems 102093P 1572 Series Cisco Aironet 802.11ac Dual Band Access Points User Manual 1570hig
Cisco Systems Inc 1572 Series Cisco Aironet 802.11ac Dual Band Access Points 1570hig
Contents
- 1. Cisco_Aironet 1570 Series_Datasheet
- 2. Install conditions 5600-5650 data_sheet
- 3. Install Guide AIR-AP1570 Series
Install Guide AIR-AP1570 Series
![Cisco Systems, Inc.www.cisco.comCisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices.Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOctober, 2014Text Part Number: OL-32138-01](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-1.png)
![THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help. Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.© 2014 Cisco Systems, Inc. All rights reserved.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-2.png)
![iiiCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01 CONTENTSPreface viiObjectives viiAudience viiOrganization viiiConventions viiiRelated Documents xivFinding the Product Serial Number xvObtaining Documentation, Support, and Security Guidelines xviCHAPTER 1Overview 1-1About the Access Point 1-1Hardware Models and Supported Regulatory Domains 1-2Features of the Access Point 1-3Processing Subsystem and Storage 1-3Operating Modes 1-3Antennas 1-4AIR-AP1572I Internal Antennas 1-4AIR-AP1572E External Antennas 1-4Non-Cisco Antennas 1-4Antenna Configurations 1-5Radios 1-5Power Sources 1-6Power-over-Cable 1-7AC Power Supply 1-8DC Interface 1-8PoE-Input 1-8Optional Hardware 1-8Network Deployment Examples 1-10Wireless Backhaul 1-10Point-to-Point Bridging 1-10Point-to-Multipoint Bridging 1-11Point-to-Multipoint Mesh Network 1-13](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-3.png)
![ContentsivCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Layer 3 Network Operation 1-14CHAPTER 2Installing the Access Point 2-1Unpacking the Access Point 2-2Package Contents 2-2Tools and Hardware 2-2Optional Tools and Hardware 2-2Optional Tools and Hardware That You Supply 2-3Warnings 2-3Safety Information 2-4FCC Safety Compliance Statement 2-4Safety Precautions 2-4Avoiding Damage to Radios in a Testing Environment 2-6Installation Guidelines 2-6Site Surveys 2-7Before Beginning the Installation 2-8Becoming Familiar with the Access Point Versions 2-9Becoming Familiar with Access Point Installation Components 2-12Mounting the Access Point 2-12Strand Mount Kits (SMKs) 2-13Pole Mount Kits (PMKs) 2-13Pedestal Mount Kits 2-13Access Point Mounting Orientation 2-13Wall Mounting the Access Point 2-14Pole Mounting the Access Point 2-16Installing Antennas 2-17Non-Cisco Antennas 2-18Safety Precautions when Installing Antennas 2-18Antenna Configurations 2-18Integrated Antenna Option 2-18External Antenna Mounting Configurations 2-19Antenna N-Type Connector Locations 2-25Installing a Lightning Arrestor 2-25Installation Considerations 2-26Installation Notes 2-26Installing the Lightning Arrestor Outdoors 2-26Cable for the Lightning Arrestor 2-27Grounding the Access Point 2-27](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-4.png)
![ContentsvCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Powering the Access Point 2-28Connecting a 1570 Series Power Injector 2-29Connecting an Ethernet Cable to the Access Point 2-30Connecting a DC Power Cable to the Access Point 2-32Connecting Streetlight AC Power 2-37Wiring the Streetlight Power Tap Adapter to the AC/DC Power Adapter 2-38Configuring the Access Point 2-39What to Do Next 2-40CHAPTER 3Troubleshooting 3-1Guidelines for Using the Access Points 3-2Important Notes 3-2Convergence Delays 3-2Bridge Loop 3-3Controller DHCP Server 3-3MAP Data Traffic 3-3Controller MAC Filter List 3-3Using DHCP Option 43 3-3Monitoring the Access Point LEDs 3-4Verifying Controller Association 3-5Changing the Bridge Group Name 3-6Access Point Power Injector 3-6Monitoring the Power Injector LEDs 3-8Using the Reset Button 3-8Resetting the Access Point 3-9APPENDIX ATranslated Safety Warnings A-1APPENDIX BDeclarations of Conformity and Regulatory Information B-1Manufacturers Federal Communication Commission Declaration of Conformity Statement B-2Industry Canada B-3Canadian Compliance Statement B-3Declaration of Conformity for RF Exposure B-4European Community, Switzerland, Norway, Iceland, and Liechtenstein B-5Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC B-5Declaration of Conformity for RF Exposure B-8United States B-8](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-5.png)
![ContentsviCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Canada B-8European Union B-8Australia B-8Guidelines for Operating Cisco Aironet Access Points in Japan B-10Japanese Translation B-10English Translation B-10VCCI Statement for Japan B-11Administrative Rules for Cisco Aironet Access Points in Taiwan B-11Chinese Translation B-11English Translation B-12Chinese Translation B-12English Translation B-12Statement 371—Power Cable and AC Adapter B-13English Translation B-13EU Declaration of Conformity B-13Operation of Cisco Aironet Access Points in Brazil B-13Access Point Models B-13Regulatory Information B-14Portuguese Translation B-14English Translation B-14APPENDIX CChannels and Power Levels C-1APPENDIX DAccess Point Data Sheet D-1APPENDIX EAccess Point Pinouts E-1APPENDIX FConfiguring DHCP Option 43 F-1Overview F-2Configuring Option 43 for 1000, 1500, and 1570 Series Access Points F-3Configuring Option 43 for 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1570 Series Access Points F-4GLOSSARY](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-6.png)
![viiCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01PrefaceThis section describes the objectives, audience, organization, and conventions of the Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide. ObjectivesThis publication explains the steps for installing the Cisco Aironet 1570 Series Outdoor Access Point (called the access point, or abbreviated as AP in this document). The access point is available in an internal antenna model with cable modem (AIR-AP1572IC), an external antenna AC model (AIR-AP1572EAC) and an external antenna model with cable modem (AIR-AP1572EC). The 1570 series is a dual-radio platform that supports dual-band (2.4 GHz and 5 GHz) operation. AudienceThis publication is for the person installing and configuring an access point for the first time. The installer should be familiar with network structures, terms, and concepts.WarningOnly trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030WarningThis equipment must be installed in restricted access locations in Norway, Finland, and Sweden. Only trained and qualified personnel are allowed to install, replace, or service this equipment as instructed in this installation guide.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-7.png)
![viiiCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01 OrganizationThis guide contains the following sections:ConventionsThis publication uses the following conventions:Chapter Title DescriptionChapter 1 Overview Describes the major components and features of the access point.Chapter 2 Installing the Access Point Provides warnings, safety information, and mounting information you need to install your access point.Chapter 3 Troubleshooting Provides basic troubleshooting procedures for the access point. Appendix A Translated Safety Warnings Indicates how to access the document that provides translations of the safety warnings that appear in this publication.Appendix B Declarations of Conformity and Regulatory InformationDescribes the regulatory conventions to which the access point conforms and provides guidelines for operating access points in Japan.Appendix C Channels and Power Levels Indicates how to access the document that lists the access point radio channels and the maximum power levels supported by the world regulatory domains.Appendix D Access Point Data Sheet Lists technical specifications for the access point.Appendix E Access Point Pinouts Describes the connector pinouts for the access point.Appendix F Configuring DHCP Option 43Describes the procedure to configure DHCP Option 43.Convention Descriptionboldface font Commands, command options, and keywords are in boldface.italic font Arguments for which you supply values are in italics.[ ] Elements in square brackets are optional.screen font Terminal sessions and information the system displays are in screen font.boldface screen font Information you must enter is in boldface screen font.italic screen font Arguments for which you supply values are in italic screen font.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-8.png)
![ixCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01 Notes use the following conventions:Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.Cautions use the following conventions:Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.Warnings use the following conventions:^ The symbol ^ represents the key labeled Control. For example, the key combination ^D in a screen display means hold down the Control key while you press the D key.< > Nonprinting characters, such as passwords, are in angle brackets.Convention DescriptionWarningIMPORTANT SAFETY INSTRUCTIONSThis warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 SAVE THESE INSTRUCTIONSWaarschuwingBELANGRIJKE VEILIGHEIDSINSTRUCTIESDit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.BEWAAR DEZE INSTRUCTIES](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-9.png)
![xCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01 VaroitusTÄRKEITÄ TURVALLISUUSOHJEITATämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.SÄILYTÄ NÄMÄ OHJEETAttentionIMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.CONSERVEZ CES INFORMATIONSWarnungWICHTIGE SICHERHEITSHINWEISEDieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.BEWAHREN SIE DIESE HINWEISE GUT AUF.AvvertenzaIMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONIAdvarselVIKTIGE SIKKERHETSINSTRUKSJONERDette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.TA VARE PÅ DISSE INSTRUKSJONENE](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-10.png)
![xiCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01 AvisoINSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.GUARDE ESTAS INSTRUÇÕES ¡Advertencia!INSTRUCCIONES IMPORTANTES DE SEGURIDADEste símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONESVarning!VIKTIGA SÄKERHETSANVISNINGARDenna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.SPARA DESSA ANVISNINGARFigyelem](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-11.png)
![xiiCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01 AvisoINSTRUÇÕES IMPORTANTES DE SEGURANÇAEste símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.GUARDE ESTAS INSTRUÇÕESAdvarselVIGTIGE SIKKERHEDSANVISNINGERDette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.GEM DISSE ANVISNINGER](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-12.png)
![xiiiCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-13.png)
![xivCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01 Related DocumentsThese documents provide complete information about the access point:•Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points •Quick Start Guide: Cisco Aironet 1570 Series Outdoor Access Points•Cisco Wireless LAN Controller Configuration GuideClick this link to browse to the Cisco Wireless documentation home page:http://www.cisco.com/en/US/products/hw/wireless/index.htmlTo browse to the access point documentation, click Cisco Aironet 1570 Series listed under “Outdoor Wireless.” The documentation can be accessed from the Support box.To browse to the Cisco Wireless LAN Controller documentation, click Standalone Controllers listed under “Wireless LAN Controllers.” The documentation can be accessed from the Support box.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-14.png)
![xvCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01 Finding the Product Serial Number The access point serial number is on the side of the access point (refer to Figure 1).Figure 1 Location of Serial Number Label The access point serial number label contains the following information:•Model number, such as AIR-AP1572EAC-x-K9, where x is the regulatory domain.•Serial number, such as WCN0636279B (11 alphanumeric digits). •Access point MAC address, for example 68BDABF54600 (12 hexadecimal digits). It is located under the serial number.You need your product serial number when requesting support from the Cisco Technical Assistance Center.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-15.png)
![xviCisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01 Obtaining Documentation, Support, and Security GuidelinesFor information on obtaining documentation and support, providing documentation feedback, security guidelines, and recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.htmlTo view all new wireless documentation, click on Wireless.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-16.png)
![CHAPTER 1-1Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-011OverviewThe Cisco Aironet 1570 Series Outdoor Access Point (hereafter called the access point or AP) is a wireless outdoor access point which is designed for use in a variety of network configurations. The access point supports wireless client access, point-to-point bridging, point-to-multipoint bridging, and point-to-multipoint mesh wireless connectivity.About the Access PointThe Cisco Aironet 1570 Series Outdoor Access Point (hereafter called the access point or AP) is a high performance outdoor access point designed for service in outdoor and mesh networks.All versions of the access point have simultaneous dual-band radio consisting of an 802.11ac Wave 1 4x4:3 5 GHz radio and 4x4:3 802.11n 2.4 GHz radio. The access point versions which have a cable modem, support up to 16x8 channel bonding.The 1570 series access points have both internal and external antenna versions.The internal antenna versions (AIR-AP1572IC versions) are optimized for service provider applications using cable modem or fiber for data backhaul, rely on power-over-cable as the primary power source, and provide GPS capability as an option.The external antenna versions (AIR-AP1572E versions) have four dual band capable external antennas ports. These versions support power over Ethernet input (AIR-AP1572EAC version only), power over Ethernet output supporting up to 802.3at devices, internal AC or power over cable power supply options.The access point can be configured, monitored, and operated through a Cisco wireless LAN controller (hereafter called a controller) as described in the Cisco Wireless LAN Controller Configuration Guide. The controllers use a browser-based management system, a command-line interface (CLI), or the Cisco Prime Infrastructure (PI) network management system to manage the controller and the associated access points. The access point supports hardware-based advanced encryption standard (AES) encryption between wireless nodes to provide end-to-end security. The access point can also be deployed in an autonomous mode and be configured via the CLI.This chapter provides information on the following topics:•Hardware Models and Supported Regulatory Domains, page 1-2•Features of the Access Point, page 1-3•Network Deployment Examples, page 1-10](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-17.png)
![1-2Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewHardware Models and Supported Regulatory DomainsHardware Models and Supported Regulatory DomainsThe 1570 series access points have model numbers in the format AIR-AP157wxyy-zzK9, where:•wx indicates the number of radios and the type of antennas. The options are:–2I—indicating two radios (4x4:3 5 GHz and 4x4:3 2.4 GHz) with internal antennas.–2E—indicating two radios (4x4:3 5 GHz and 4x4:3 2.4 GHz) with external antennas.•yy indicates whether the access point is AC powered or is the cable modem type (all cable modem versions are powered by Power-over-cable). Internal antenna models can be powered only by Power-over-cable. External antenna models can be either AC powered, PoE or powered by Power-over-cable. The options are:–C1—Indicates Power-over-cable with North American domain (N4) cable modem supporting 5-42/ 54-1000 MHz Diplex Filter, and 8x4 or 16x4 channel bonding options.–C2— Indicates Power-over-cable with North American domain (N8) cable modem supporting 5-85/108-1002 MHz Diplex Filter, and 8x4 or 16x8 or 24x8 channel bonding options.–C3—Indicates Power-over-cable with European domain (E8) cable modem supporting 5-65/108-1002 MHz Diplex Filter, and 8x4 or 16x4 or 24x8 channel bonding options.–C4—Indicates Power-over-cable with Japanese domain (J8) cable modem supporting 5-65/108-1002 MHz Diplex Filter, and 8x4 or 16x4 or 24x8 channel bonding options. –AC— indicates AC power supply, applicable only to external antenna models.•zz indicates the regulatory domain. The supported regulatory domains are:–A-, B-, C-, D-, E-, F-, H-, K-, M-, N-, Q-, R-, S-, T-, Z-Click this URL to browse to a list of countries and regulatory domains supported by the 1570:www.cisco.com/go/aironet/compliance](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-18.png)
![1-3Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewFeatures of the Access PointFeatures of the Access PointThis section lists the features supported by the 1570 access point models:Processing Subsystem and Storage•Network management•CleanAir—Automatic detection, classification, location and mitigation of RF interference•ClientLink 3.0 —BeamForming to 802.11a/g/n/ac clients. •VideoStream•Location•WIDS/WIPS•Security•Radio Resource Management (RRM)•Rogue detection•Management Frame Protection (MFP)•512 MB DDR and 64 MB Flash Operating ModesThe following operating modes are supported by the 1570 series access points:•Unified modes:–FlexConnect–Local Mode•Workgroup Bridge (WGB) mode•Monitor mode•Spectrum Expert Mode mode•Sniffer mode•Mesh modes:–FlexConnect over Mesh–Meshing to other Cisco Aironet access points, such as the 1550 series, 1530 series, and also Cisco Aironet indoor mesh access points.–Backhaul on 2.4 GHz link.•Bridging:–Point-to-point bridging–Point-to-multi-point bridging](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-19.png)
![1-4Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewFeatures of the Access PointAntennasAll versions of 1570 series access points have 4x4:3 2.4 GHz radios and 4x4:3 5 GHz radios.AIR-AP1572I Internal AntennasAIR-AP1572I has four internal dual band antennas. The maximum 2.4 GHz gain is 4 dBi. The maximum 5 GHz gain is 5 dBi.AIR-AP1572E External AntennasAIR-AP1572E has four internal dual band antenna ports, to which the following external antennas can be connected.Non-Cisco AntennasCisco does not support any third-party antennas. RF connectivity and compliance of third party antennas is the customer’s responsibility. Cisco does not recommend any third-party antennas, and Cisco Technical Assistance Center will not be able to provide any support for third-party antennas. Cisco’s FCC Part 15 compliance is only guaranteed with Cisco antennas or antennas that are of the same design and gain as Cisco antennas.Antenna Band Operating Frequency Range (MHz) Type PortsPeak Gain (dBi)AIR-ANT2547VG-N Dual 2400 - 24835150 - 5875Omni 1 4 (2G)7 (5G)AIR-ANT2569VG-N= Dual 2400 - 24905250 - 5925Omni 1 (?)AIR-ANT2588P3M-N= Dual 2400 - 25005150 - 5900Directional 3 8 (2G)8 (5G)AIR-ANT2513P4M-N Dual 2400 - 25005150 - 5900Directional 4 13 dBi (2G) 13 dBi (5G)AIR-ANT2420V-N 2.4 GHz 2400 - 2500 Omni 1 2AIR-ANT2450V-N 2.4 GHz 2400 - 2484 Omni 1 5AIR-ANT2480V-N 2.4 GHz 2400 - 2484 Omni 1 8AIR-ANT2413P2M-N= 2.4 GHz 2400 - 2500 Directional 2 13AIR-ANT5140V-N 5 GHz 5250 - 5875 Omni 1 4AIR-ANT5180V-N 5 GHz 4900 - 5850 Omni 1 8AIR-ANT5114P2M-N= 5 GHz 5150 - 5900 Directional 2 14](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-20.png)
![1-5Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewFeatures of the Access PointAntenna ConfigurationsAll versions of the 1570 series access points contain a 4x4:3 2.4 GHz radio and a 4x4:3 5 GHz radio which are connected to physical antennas/antenna ports numbered 1, 2, 3, and 4. These radios can be configured for both dual-band (both 2.4 GHz and 5 GHz signals coming from the same antenna ports) and single band (2.4 GHz and 5 GHz signals coming from different antennas / antenna ports). The 2.4 and 5 GHz radios connected to these antennas/antenna ports are user configurable as follows:•The maximum number of active Tx/Rx antennas/antenna ports paths for both the 2.4 and 5 GHz 4x4 radios is restricted to the modes of operation set forth in Section 3.2.7.•The allowable configurations for the 4x4:3 5 GHz radio are:•The allowable configurations for the 4x4:3 2.4 GHz radio are:RadiosWarningIn order to comply with radio frequency (RF) exposure limits, the antennas should be placed no less than 50 cm (20”) from your body or nearby persons. Statement 339WarningDo not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.: NFPA 70, National Electric Code, Article 180, Canada: Canadian Electrical Code, Section 54). Statement 1052WarningOnly trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030ModeActive Antennas / Ports12342x2 Single Band Yes Yes2x2 Dual Band Yes Yes3x3 Dual Band Yes Yes Yes4x4 Dual Band Yes Yes Yes YesModeActive Antennas / Ports12342x2 Single Band Yes Yes2x2 Dual Band Yes Yes3x3 Dual Band Yes Yes Yes4x4 Dual Band Yes Yes Yes Yes](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-21.png)
![1-6Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewPower SourcesThe 1570 series access points have simultaneous 2.4 GHz 802.11b/g/n and 5 GHz 802.11a/n/ac radios, both of which support 4TX x 4RX with 3 spatial streams. The radios also support the following:•CleanAir•Support for 200 clients per radio•802.11n/ac standard requirements including:–A-MSDU RX –A-MPDU RX–Block ACK Protocol–RIFS RX–A-MPDU TX•802.11n/ac optional features including:–A-MSDU TX–Non-HT Duplicate Mode–5G: 20MHz, 40MHz, and 80 MHz Channels2.4G: 20MHz only–PHY data rates up to 216.7 Mbps for 2.4 GHz radio and1.3Gbps for 5 GHz 4x4 radio.–Maximal Ratio combining (MRC)–Cyclic Shift Diversity (CSD)–DFS (Bin 5) for U-NII 2 and U-NII 2 Extended channels, including 0.5us radar pulse detection–STBC (Space Time Block Coding) MCS 0-7 (802.11n modes) •High-Density Deployments (Dynamically Adjustable SOP/CCA thresholds)•DRA (Rate Shifting)•ClientLink 3.0 (Beamforming)Power SourcesWarningInstallation of the equipment must comply with local and national electrical codes. Statement 1074WarningThis equipment must be externally grounded using a customer-supplied ground wire before power is applied. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 366WarningDo not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-22.png)
![1-7Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewPower SourcesWarningConnect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033WarningTo reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023Caution Power injectors must be used indoors only. Do not place a power injector in an unprotected outdoor environment because water could get into the power injector and cause a short circuit and possible fire.Caution When the access point is installed outdoors or in a wet or damp location, the AC branch circuit that is powering the access point should be provided with ground fault protection (GFCI), as required by Article 210 of the National Electrical Code (NEC).Depending on the version of the access point, you may have the following power options available in your access point:•Power-over-cable (PoC) - The only source for internal antenna versions (AIR-AP1572I versions)•AC•DC•UPOE (or AIR-PWRINJ1500-2 power injector)The external antenna versions (AIR-AP1572E versions) support power over Ethernet input (on the AC version only), power over Ethernet output supporting up to 802.3at devices, internal AC or power over cable power supply options.If multiple power sources are available, the access point will select the power source which is higher on the following prioritization list. If a power source is removed, access point will automatically switch to the next available power source, as per this list:1. Power-over-cable or AC (whichever is available on your AP)2. External DC input3. PoE (available in AC powered versions of AP)Power-over-CableAll versions of AIR-AP1572I and some versions of AIR-AP1572E are equipped with a power-over-cable (PoC) power supply. The power supply can accept quasi-AC signals in the 40 to 90 V RMS range. Versions of the AP that have a PoC power supply, also have a shunt/fuse interface providing direct in-line access to the PoC AC signal. The AP comes with a shunt in the shunt/fuse location. By removing the shunt or fuse, field technicians can immediately remove power to the AP for service and repairs, and then restore power by re-installing the shunt or fuse. You can install a fuse in the shunt/fuse location to limit the maximum sustained current supplied to the AP to prevent damage to the AP or to the cable plant. Fuses of various amperage are available, and so you can select the appropriate fuse rating depending on the configuration and operating voltage.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-23.png)
![1-8Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewOptional HardwareAC Power SupplyNon PoC versions of the AP come equipped with an AC power supply. The power supply is designed to accept AC signals from 100 to 305 V RMS with a margin of +/- 10%. The following AC power cords are supported:DC InterfaceAll versions of the AP have an externally accessible DC input connector. The DC input accepts voltages in the 9 to 16V range.PoE-InputAC powered versions of AIR-AP1572E can be powered by UPOE compliant power sourcing equipment.In addition to being powered by UPOE sources, the access point can also be powered by the AIR-PWRINJ1500-2 power injector.The access point also supports an Ethernet uplink port (PoE-In). The access point Ethernet uplink port uses an RJ-45 connector (with weatherproofing) to link the access point to the 10BASE-T, 100BASE-T or 1000BASE-T network. The Ethernet cable is used to send and receive Ethernet data and to optionally supply inline power from the power injector or a suitably powered switch port.Tip The access point senses the Ethernet and power signals and automatically switches internal circuitry to match the cable connections.The Ethernet cable must be a shielded outdoor rated Category 5e (CAT5e) or better cable. The access point senses the Ethernet and power signals and automatically switches internal circuitry to match the cable connections.Optional HardwareDepending on what you ordered, the following optional access point hardware may be part of your shipment:•External antennas, depending on which ones you purchased •Power injector AIR-PWRINJ1500-2•AP cover / Solar Shield Product ID DescriptionAIR-CORD-R3P-40NA= Power cord, 40 ft, North American PlugAIR-CORD-R3P-40UE= Power cord, 40 ft, European Harmonized, Un-terminatedAIR-PWR-ST-LT-R3P= Power cord, 4 ft, Street Light Tap](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-24.png)
![1-9Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewOptional Hardware•AC/DC power adapter, spare only•GPS antenna•Strand Mount kits•Pole Mount kit•Pedestal Mount kit•Spare Parts kit containing extra cable glands, power connector, ground lug, etc.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-25.png)
![1-10Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewNetwork Deployment ExamplesNetwork Deployment ExamplesThe access point is a wireless device designed for wireless client access and point-to-point bridging, point-to-multipoint bridging, and point-to-multipoint mesh wireless connectivity. The access point provides 5-GHz backhaul capability to link with another access point to reach a wired network connection or to provide repeater operations for other access points.The access point plays two primary radio roles: a root access point (hereafter called a RAP) or a mesh (non-root) access point (hereafter called a MAP), which is the default role of all access points. When the access point has a fiber or wired Ethernet connection to the controller (through a switch), the radio role is called a RAP. In order to be considered a RAP, the access point must be configured as a RAP. A RAP is a parent node to any bridging or mesh network. A controller can support one or more RAPs, each one parenting the same or different wireless networks. There can be more than one RAP for the same mesh network for redundancy. RAPs and MAPs can support wireless clients on the 2.4-GHz and 5-GHz band. Client access on 5-GHz is called universal client access.When the access point does not have a wired Ethernet connection to the controller (through a switch), the radio role is called a MAP. The MAPs have a wireless connection (through the backhaul interface) to other MAPs and finally to a RAP which has an Ethernet connection through a switch to the controller. MAPs may also have a wired Ethernet connection to a local LAN and serve as a bridge endpoint for that LAN (using a point-to-point or point-to-multipoint bridge connection). Wireless BackhaulThe access point supports wireless backhaul capability using the 5 GHz radio to bridge to another access point to reach a wired network connection to a controller (see Figure 1-1). The access point connected to the wired network is considered a RAP in this configuration. The remote access point is considered a MAP and transfers wireless client traffic to the RAP for transfer to the wired network. Control And Provisioning of Wireless Access Points (CAPWAP) control traffic is also transferred over this bridged link.Figure 1-1 Access Point Backhaul ExamplePoint-to-Point Bridging The access points can be used to extend a remote network by using the 5 GHz backhaul radio to bridge the two network segments as shown in Figure 1-2. To support Ethernet bridging, you must enable bridging on the controller for each access point. By default this capability is turned-off for all access points.255493(5 GHz) (2.4 GHz and 5 GHz)](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-26.png)
![1-11Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewNetwork Deployment ExamplesWireless client access is supported; however, if bridging between tall buildings, the 2.4-GHz wireless coverage area may be limited and possibly not suitable for direct wireless client access.Figure 1-2 Access Point Point-to-Point Bridging ExampleThe access points can also support point-to-point bridging under autonomous mode. In this autonomous mode, the bridging can be done on the 2.4 or 5 GHz radio, but not both. In this mode, one access point is designated as the root and the other end is designated as the non-root bridge.Figure 1-3 Access Point Point-to-Point Bridging in Autonomous ModePoint-to-Multipoint BridgingThe access points can be used as a RAP to connect multiple remote MAPs with their associated wired networks. By default this capability is turned-off for all access points. To support Ethernet bridging, you must enable bridging on the controller for each access point. Wireless client access can be provided over the bridging link; however, if bridging between tall buildings, the 2.4-GHz wireless coverage area may be limited and possibly not suitable for direct wireless client access. Figure 1-4 illustrates an example of access point-to-multipoint bridging.255495(5 GHz)3520522.4 GHz or 5 GHz](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-27.png)
![1-12Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewNetwork Deployment ExamplesFigure 1-4 Access Point to Multipoint Bridging ExampleThe access points can also support point-to-multipoint bridging under autonomous mode. In this autonomous mode, the bridging can be done on the 2.4 or 5 GHz radio, but not both. In this mode, one access point is designated as the root and the other end is designated as the non-root bridge.Figure 1-5 Access Point to Multipoint Bridging in Autonomous Mode255494(5 GHz)(5 GHz)3520512.4 GHz or 5 GHz2.4 GHz or 5 GHz](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-28.png)
![1-13Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewNetwork Deployment ExamplesPoint-to-Multipoint Mesh NetworkThe access point is typically deployed in a mesh network configuration. In a typical mesh deployment, one or more RAPs have a wired network connection through a switch to a controller. Other remote MAPs without wired network connections use the backhaul feature to optimally link to a RAP that is connected to the wired network. In the mesh network, the links between the access points are referred to as the backhaul links.Intelligent wireless routing is provided by the Adaptive Wireless Path protocol (AWPP). This enables each MAP to identify its neighbors and intelligently choose the optimal path to the RAP with the wired network connection by calculating the cost of each path in terms of signal strength and the number of hops required to get to a controller with signal strength given priority since signal strength determines the data rate available for backhaul.Figure 1-6 illustrates a typical mesh configuration using MAPs and RAPs.Figure 1-6 Typical Mesh Configuration Using Access Points351994CPINetworkRAPMAP 1 MAP 2 MAP 3MAP 4 MAP 6MAP 5MAP 7 MAP 8 MAP 9](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-29.png)
![1-14Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 1 OverviewNetwork Deployment ExamplesLayer 3 Network OperationThe access points support Layer 3 network operation. Access points and controllers in Layer 3 configurations use IP addresses and UDP packets, which can be routed through large networks. Layer 3 operation is scalable and recommended by Cisco.Figure 1-7 illustrates a typical Layer-3 wireless network configuration containing access points and a controller.Figure 1-7 Typical Layer 3 Access Point Network Configuration Example148458](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-30.png)
![CHAPTER 2-1Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-012Installing the Access PointThis chapter describes how to install the 1572 access point and contains the following sections:•Unpacking the Access Point, page 2-2•Tools and Hardware, page 2-2•Warnings, page 2-3•Safety Information, page 2-4•Avoiding Damage to Radios in a Testing Environment, page 2-6•Installation Guidelines, page 2-6•Mounting the Access Point, page 2-12•Installing Antennas, page 2-17•Grounding the Access Point, page 2-27•Powering the Access Point, page 2-28•Powering the Access Point, page 2-28•Configuring the Access Point, page 2-39•What to Do Next, page 2-40](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-31.png)
![2-2Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointUnpacking the Access PointUnpacking the Access PointTo unpack the access point, follow these steps:Step 1 Open the shipping container and carefully remove the contents. Step 2 Return all packing materials to the shipping container, and save it.Step 3 Ensure that all items listed in “Package Contents” are included in the shipment. If any item is damaged or missing, notify your authorized Cisco sales representative. Package ContentsEach access point package contains the following items:•One 1570 series access point•Ground lug and screws with lock washers•Plastic cable gland and rubber seal•Weatherization tape and anti-corrosion sealant•Cisco product documentation and pointer cardTools and HardwareThe tools and hardware used to install the 1572 access point are described in:•Optional Tools and Hardware, page 2-2•Optional Tools and Hardware That You Supply, page 2-3•Warnings, page 2-3•Warnings, page 2-3Optional Tools and HardwareDepending on what you ordered, the following optional equipment may be part of your shipment:•External antennas, depending on which ones you purchased.•Wall/Pole mount bracket, available as an option or a spare (AIR-ACC1570-PMK1[=])•Wall/Pole mount bracket with tilt mechanism, spare only (AIR-ACC1570-PMK2=)•AC/DC power adapter, spare only (AIR-PWRADPT-1570=)•Spare Parts kit containing extra cable glands, power connector, ground lug, etc. (AIR-ACC1570-KIT1=)•FIPS kit (AIRLAP-FIPSKIT=)](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-32.png)
![2-3Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointWarningsOptional Tools and Hardware That You SupplyTools and materials that are user-supplied are:•Ground lug crimping tool (Panduit CT-720 with CD-720-1 die) •6-AWG copper ground wire•10 mm open end or box wrench•13 mm box-end wrench or socket set•Adjustable wrench with opening up to 33 mm and 28 mm socket.•Large flat or Phillips screw driver (for port plugs)•Small flat screwdriver for DC power connector•Optional shielded outdoor-rated Ethernet (CAT5e or better) cable with 0.20 to 0.35 in (0.51 to 0.89 cm) diameter•Optional Ethernet RJ-45 connector and installation tool•Optional shielded outdoor-rated DC power cable with 0.20 to 0.35 inch (.0.51 to 0.89 cm) diameter•Optional ground rod, as required by local regulations•Optional ladder, power lift, rope, or other tools as requiredWarningsTranslated versions of all safety warnings are available in the safety warning document that shipped with your access point or on Cisco.com. To browse to the document on Cisco.com, refer to Appendix A, “Translated Safety Warnings” for instructions. WarningIMPORTANT SAFETY INSTRUCTIONSThis warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071SAVE THESE INSTRUCTIONSWarningThis equipment is to be installed by trained and qualified personnel, as per these installation instructions. The installer is responsible for obtaining any required local or national safety inspections of the structural integrity of the installation by the local authority/inspection department.WarningDo not operate the unit near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use. Statement 364](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-33.png)
![2-4Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointSafety InformationWarningThe cables specified in this installation guide that are used with the specified cable glands provide protection against ingress of moisture for a Type 4/IP67 classified enclosure. If substitute cable are used, the installer must ensure that the size (OD) of the cable meets the acceptable range allowed by the cable gland.WarningThis equipment must be externally grounded using a customer-supplied ground wire before power is applied. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 366WarningRead the installation instructions before connecting the system to the power source. Statement 1004WarningUltimate disposal of this product should be handled according to all national laws and regulations. Statement 1040Safety InformationFollow the guidelines in this section to ensure proper operation and safe use of the access point.FCC Safety Compliance StatementThe FCC, with its action in ET Docket 96-8, has adopted a safety standard for human exposure to RF electromagnetic energy emitted by FCC-certified equipment. When used with approved Cisco Aironet antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper operation of this radio device according to the instructions in this publication results in user exposure substantially below the FCC recommended limits.Safety PrecautionsWarningIn order to comply with radio frequency (RF) exposure limits, the antennas should be placed no less than 50 cm (20”) from your body or nearby persons. Statement 339WarningDo not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001WarningA readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 1022](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-34.png)
![2-5Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointSafety InformationWarningTo reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023WarningThis unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028WarningOnly trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030WarningConnect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033WarningWhen installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046.WarningDo not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 1052Caution Before connecting or disconnecting a power cord, you must remove power from the power cord using a suitable service disconnect.For safety and to achieve a good installation, please read and follow these safety precautions:•Select your installation site with safety, as well as performance in mind. Remember: electric power lines and phone lines look alike. For safety, assume that any overhead line can kill. •Call your electric power company. Tell them your plans, and ask them to come look at your proposed installation. •Plan your installation carefully and completely before you begin. Successful raising of a mast or tower is largely a matter of coordination. Each person should be assigned to a specific task and should know what to do and when to do it. One person should be in charge of the operation to issue instructions and watch for signs of trouble.•When installing the access point and antennas, remember:–Do not use a metal ladder.–Do not work on a wet or windy day.–Do dress properly—shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.•Use a rope to lift the access point. If the assembly starts to drop, get away from it and let it fall.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-35.png)
![2-6Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointAvoiding Damage to Radios in a Testing Environment•If any part of the antenna system should come in contact with a power line, do not touch it or try to remove it yourself. Call your local power company. They will remove it safely. If an accident should occur, call for qualified emergency help immediately.Avoiding Damage to Radios in a Testing EnvironmentThe radios on outdoor units (bridges) have higher transmit power levels than radios on indoor units (access points). When you test high-power radios in a link, you must avoid exceeding the maximum receive input level for the receiver. At levels above the normal operating range, packet error rate (PER) performance is degraded. At even higher levels, the receiver can be permanently damaged. To avoid receiver damage and PER degradation, you can use one of the following techniques:•Separate the omnidirectional antennas by at least 2 ft (0.6 m) to avoid receiver damage or by at least 25 ft (7.6 m) to avoid PER degradation.Note These distances assume free space path loss and are conservative estimates. Required separation distances for damage and performance degradation levels in actual deployments are less if conditions are not non-line-of-sight.•Reduce the configured transmit power to the minimum level.•Use directional antennas, and keep them away from each other.•Cable the radios together using a combination of attenuators, combiners, or splitters to achieve a total attenuation of at least 60 dB.For a radiated test bed, the following equation describes the relationships among transmit power, antenna gain, attenuation, and receiver sensitivity:txpwr + tx gain + rx gain - [attenuation due to antenna spacing] < max rx input levelWhere:txpwr = Radio transmit power leveltx gain = transmitter antenna gainrx gain = receiver antenna gainFor a conducted test bed, the following equation describes the relationships among transmit power, antenna gain, and receiver sensitivity:txpwr - [attenuation due to coaxial components] < max rx input levelCaution Under no circumstances should you connect the antenna port from one access point to the antenna port of another access point without using an RF attenuator. If you connect antenna ports, you must not exceed the maximum survivable receive level of 0 dBm. Never exceed 0 dBm, or damage to the access point can occur. Using attenuators, combiners, and splitters having a total of at least 60 dB of attenuation ensures that the receiver is not damaged and that PER performance is not degraded.Installation GuidelinesBecause the access point is a radio device, it is susceptible to common causes of interference that can reduce throughput and range. Follow these basic guidelines to ensure the best possible performance:•For information on planning and initially configuring your Cisco Mesh network, refer to the Cisco Wireless Access Points, Design and Deployment Guide, Release 7.3.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-36.png)
![2-7Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstallation Guidelines•Review the FCC guidelines for installing and operating outdoor wireless LAN devices at http://www.cisco.com/en/US/partner/prod/collateral/routers/ps272/data_sheet_c78-647116_ps11451_Products_Data_Sheet.html.•Perform a site survey before beginning the installation.•Install the access point in an area where structures, trees, or hills do not obstruct radio signals to and from the access point.•The access points can be installed at any height, but best throughput is achieved when all the access points are mounted at the same height. We recommend installing the access points no higher than 40 feet to allow support for wireless clients on the ground.Note To calculate path loss and to determine how far apart to install access points, consult an RF planning expert.Site SurveysEvery network application is a unique installation. Before installing multiple access points, you should perform a site survey to determine the optimum use of networking components and to maximize range, coverage, and network performance.Site surveys reveals problems that can be resolved before the network is operational. Because 802.11a/b/g/n operates in an unlicensed spectrum, there may be sources of interference from other 802.11a wireless devices (especially in multi-tenant buildings) that could degrade your 802.11 signals. A site survey can determine if such interference exists at the time of deployment. A proper site survey involves temporarily setting up mesh links and taking measurements to determine whether your antenna calculations are accurate. Determine the correct locations and antenna types before you drill holes and route cables and mounting equipment. Consider the following operating and environmental conditions when performing a site survey:•Data rates—Sensitivity and range are inversely proportional to data bit rates. The maximum radio range is achieved at the lowest workable data rate. A decrease in receiver sensitivity occurs as the radio data increases.•Antenna type and placement—Proper antenna configuration is a critical factor in maximizing radio range. As a general rule, range increases in proportion to antenna height. However, do not place the antenna higher than necessary, because the extra height also increases potential interference from other unlicensed radio systems and decreases the wireless coverage from the ground.•Physical environment—Clear or open areas provide better radio range than closed or filled areas. •Obstructions—Physical obstructions such as buildings, trees, or hills can hinder performance of wireless devices. Avoid locating the devices in a location where there is an obstruction between the sending and receiving antennas.•How far is your wireless link?•Has a previous site survey been conducted?•Do you have a clear Fresnel zone between the access points or radio line of sight?•What is the minimum acceptable data rate within the link?•Do you have the correct antenna (if more than one antenna is being offered?)•Do you have access to both of the mesh site locations?](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-37.png)
![2-8Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstallation Guidelines•Do you have the proper permits, if required?•Are you following the proper safety procedures and practices?•Have you configured the access points before you go onsite? It is always easier to resolve configurations or device problems first.•Do you have the proper tools and equipment to complete your survey.Before Beginning the InstallationBefore you begin the installation process:•Ensure that a site survey has been performed.•Ensure that your network infrastructure devices are operational and properly configured.•Ensure that your controllers are connected to switch trunk ports.•Ensure that your switch is configured with untagged access ports for connecting your access points.•Ensure that a DHCP server with Option 43 configured is reachable by your access points, or manually configure the controller information in the access point (for additional information, refer to the “Configuring DHCP Option 43” section on page F-1).•Become familiar with the access point installation components (see the “Becoming Familiar with Access Point Installation Components” section on page 2-12).](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-38.png)
![2-9Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstallation GuidelinesBecoming Familiar with the Access Point VersionsFigure 2-1 1570I Series AP Top-Front Three Quarter ViewFigure 2-2 1570I Series AP Front-Bottom Three Quarter View](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-39.png)
![2-10Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstallation GuidelinesFigure 2-3 1570E Series AP Front ViewFigure 2-4 1570E Series AP Top-Front Three Quarter View](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-40.png)
![2-11Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstallation GuidelinesFigure 2-5 1570E Series AP Front-Bottom Three Quarter ViewFigure 2-6 1570E Series AP with AC Port Top-Front Three Quarter View](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-41.png)
![2-12Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointMounting the Access PointFigure 2-7 1570E Series AP with AC Port Front-Bottom Three Quarter ViewBecoming Familiar with Access Point Installation ComponentsThe access point is designed to be installed in an outdoor environment. The illustrations in this document show all available connections for the access point. Unused connections are capped with a connector plug to ensure the watertight integrity of the access point. Cable glands are provided for connector openings, which can be installed before or after deploying the access point. WarningInstallation of the equipment must comply with local and national electrical codes. Statement 1074Mounting the Access PointThis section provides instructions for installing your access points. Personnel installing the access point must understand wireless access points and bridging techniques and grounding methods. The 1570 Series Access Point can be strand, pole or pedestal mounted.Caution All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-42.png)
![2-13Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointMounting the Access PointWarningOnly trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030WarningInstallation of the equipment must comply with local and national electrical codes. Statement 1074Strand Mount Kits (SMKs)All versions of the 1570 series AP can be mounted to a strand. Two strand mount kits are available. One version of the strand mount kit (SMK) is for mounting the AP directly to the strand when there is no cable bundle. The other version is for mounting the AP to the strand in the presence of a 1.75 inch cable strand and is approximately 2.25 inches from the top of the AP to the center of the cable strand.Pole Mount Kits (PMKs)All versions of the 1570 series AP can be mounted to either a pole or wall using a pole mount kit (PMK). One PMK is designed specifically for the 1570I series and another PMK is designed specifically for the 1570E series.The 1570I PMK allows the AP to be mounted in a horizontal orientation with antennas downward when attached to a horizontal pole, vertical pole, or wall. The 1570E PMK allows the AP to be mounted vertically when attached to a horizontal pole, vertical pole, or wall. Arbitrary off angle poles are not supported. Both PMKs can be mounted to poles in diameter from 2 to 16 inches. Both PMKs maintain a low profile with approximately 1 inch clearance between the pole/wall and the AP. Pedestal Mount KitsThe 1570I series AP has a pedestal mount kit that allows it to be installed into a Channell 1420 pedestal housing. The 1570E has a pedestal mount allowing it to be installed into a Channell 1212 pedestal housing.Access Point Mounting OrientationWhen mounting an access point on a horizontal or vertical surface, you must ensure that the access point is oriented with the LED indicators pointing down. This positioning allows LEDs to be visible to someone on the ground below the access point.You must also ensure the access point is mounted in such a way as to ensure that all antenna ports and the console port are accessible for future use.Note Omnidirectional antennas are vertically polarized and should be mounted vertically.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-43.png)
![2-14Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointMounting the Access PointWall Mounting the Access PointThe optional PMK contains a mounting bracket for wall mounting or pole mounting. You can use the mounting bracket as a template to mark the positions of the mounting holes for your installation. You then install the mounting plate, and attach the access point when you are ready. Table 2-1 lists the materials you will need in addition to the mounting kit.Ta b l e 2 - 1 Materials Required to Mount Access Point to a Vertical WallCaution The mounting surface, attaching screws and optional wall anchors must be able to support a 50-lb (22.7 kg) static weight.To mount the access point on a vertical wall, follow these instructions:Step 1 Use the mounting bracket as a template to mark four screw hole locations on the mounting surface. See Figure 2-8 for the mounting bracket screw hole locations. Use the mounting slotted holes to attach the unit to the wall.Materials Required to Mount Access Point to a Vertical Wall In KitGround lug and screws (provided with access point) YesWall Mount Bracket YesFour M6 x 12-mm Hex-head Bolts YesTwo stainless steel band clamps (adjustable 2"–5", 51 mm – 127 mm)YesTwo stainless steel band clamps(adjustable 5"–8", 127 mm – 203 mm)YesCrimping tool for ground lug, Panduit CT-720 with CD-720-1 die (http://www.panduit.com)NoFour wall mounting screws NoFour wall anchors (specified for all material) NoDrill bit for wall anchors NoElectric drill and standard screwdriver No#6 AWG ground wire NoShielded outdoor-rated Ethernet (CAT5e or better) cable NoGrounding block NoGrounding rod No10-mm box-end wrench or socket set No](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-44.png)
![2-15Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointMounting the Access PointFigure 2-8 Mounting Bracket for Wall and Pole MountingStep 2 Use four customer-supplied screws and optional screw-anchors to attach the mounting plate to the mounting surface.Note If necessary, use suitable screw anchors and an exterior-grade plywood backboard to mount the access point to stucco, cement or drywall.Figure 2-9 Mounting Bracket Dimensions1Quick Mount Keyhole Slots (for AP use) 2Mounting Slots (used with the band clamps)3Bracket Mount Holes (use bolts up to 1/4" or 6 mm in diameter)347852123](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-45.png)
![2-16Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointMounting the Access PointStep 3 Screw an M6 x12 mm bolt into each of the four support bolt holes on the back of the access point. Do not screw the bolt all the way in; leave approximately a 0.13 inch (3.3 mm) space.Step 4 Position the four bolts on the access point into the keyhole slots on the mounting bracket.Step 5 Slide the access point down to sit securely in the quick mount notches.Step 6 Using a 10mm wrench, secure the AP to the bracket by tightening the bolts to the bracket; torque to 40 lb-in.Step 7 Continue with the Grounding the Access Point, page 2-27. Pole Mounting the Access PointThe optional PMK contains a mounting bracket for wall mounting or pole mounting.This kit can be used to install the access point on a pole, mast or streetlight. It supports metal, wood or fiberglass poles from 2 to 8 inches in diameter.Ta b l e 2 - 2 Materials Needed to Mount the AP on a Vertical PoleTo mount the access point onto a vertical pole or streetlight pole, follow these steps:Step 1 Select a mounting location on the pole to mount the access point. You can attach the access point to any pole with a diameter from 2to 8 inches (5.1 to 20.1 cm).Note If you will be using a streetlight power tap adapter, position the access point within 3 ft (1 m) of the outdoor light control. The AC/DC adapter must be used with street light power tap.Step 2 Determine which size of band clamp is needed based on the pole diameter. Slide the two clamps through the top and bottom set of mounting slots (see Figure 2-8) and mount the bracket to the pole.Step 3 Wrap the band clamps around the pole and slide them into the second set of top and bottom mounting slots on the bracket. Lightly tighten the clamps. Only tighten them enough to keep the bracket from sliding down the pole.Materials Needed to Mount the AP on a Vertical Pole In KitOne wall mount bracket YesFour M6 x12mm hex head bolts YesTwo stainless steel band clamps (adjustable 2"–5", 51–127 mm)YesTwo stainless steel band clamps (adjustable 5"–8", 127–203 mm)Yes10 mm box-end wrench NoOutdoor rated shielded ethernet cable NoGround lug (provided with the access point) YesGround block and rod NoCrimping tool for ground lug, Panduit CT-720 with CD-720-1 die (http://www.panduit.com)No#6 AWG ground wire No](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-46.png)
![2-17Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstalling AntennasStep 4 Screw an M6 bolt into each of the four bolt holes on the back side of the access point. Do not screw the bolt in all the way. Leave a gap of about 0.13" (3.3mm).Step 5 Position the four bolts on the access point into the bracket keyhole slots. Check to be sure that the access point is properly seated in the slots.(See Figure 2-6)Note The access point should be positioned with the LEDs on the bottom to allow viewing from the ground.Step 6 Using a 10mm wrench, tighten the four bolts that connect the access point to the bracket to a torque of 40 lbf-in. Step 7 Locate the access point to its final position. Tighten the band clamps with the wrench so that the access point does not slide on the pole. Ensure that the clamps are tight enough to not let the AP move.Step 8 Continue with the Grounding the Access Point, page 2-27. Installing AntennasTable 2-3 shows the antennas supported by the 1572 access point and provides required quantities for each model.For installation instructions and detailed information on these antennas, refer to the appropriate document located at:http://www.cisco.com/en/US/products/hw/wireless/ps469/prod_installation_guides_list.htmlFollow all safety precautions when installing the antennas. For information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-18.Table 2-3 1572 Access Point Supported External AntennasProduct IDFrequency Band Gain TypeAIR-ANT2547VG-N 2.4 / 5 GHz 4 / 7 dBi Omnidirectional (gray)AIR-ANT2547V-N 2.4 / 5 GHz 4 / 7 dBi Omnidirectional (white)AIR-ANT2588P3M-N= 2.4 / 5 GHz 4 / 7 dBi OmnidirectionalAIR-ANT2588P3M-N 2.4 / 5 GHz 8 / 8 dBi DirectionalAIR-ANT2450V-N 2.4 GHz 5 dBi OmnidirectionalAIR-ANT2480V-N 2.4 GHz 8 dBi OmnidirectionalAIR-ANT2413P2M-N= 2.4 GHz 13 dBi DirectionalAIR-ANT5180V-N 5 GHz 8 dBi OmnidirectionalAIR-ANT5114P2M-N= 5 GHz 14 dBi Directional](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-47.png)
![2-18Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstalling AntennasNon-Cisco AntennasCisco does not support any third-party antennas. RF connectivity and compliance of third party antennas is the customer’s responsibility. Cisco does not recommend any third-party antennas, and Cisco Technical Assistance Center will not be able to provide any support for third-party antennas. Cisco’s FCC Part 15 compliance is only guaranteed with Cisco antennas or antennas that are of the same design and gain as Cisco antennas.Safety Precautions when Installing AntennasWarningDo not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, as they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (e.g. U.S.: NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 2801. Before you install an antenna, contact your Cisco account representative to explain which mounting method to use for the size and type of antenna that you are about to install.2. Select your installation site with safety, as well as performance, in mind. Remember that electric power lines and phone lines look alike. For your safety, assume that any overhead line can kill you.3. Contact your electric power company. Tell them your plans and ask them to come look at your proposed installation.4. Plan your installation carefully and completely before you begin. Each person involved in an installation should be assigned to a specific task and should know what to do and when to do it. One person should be in charge of the operation to issue instructions and watch for signs of trouble.5. When installing your antenna, follow these guidelines:–Do not use a metal ladder.–Do not work on a wet or windy day.–Do dress properly—wear shoes with rubber soles and heels, rubber gloves, and a long-sleeved shirt or jacket.6. If the assembly starts to drop, move away from it and let it fall. Because the antenna, mast, cable, and metal guy wires are all excellent conductors of electrical current, even the slightest touch of any of these parts to a power line completes an electrical path through the antenna and the installer.7. If any part of the antenna system should come in contact with a power line, do not touch it or try to remove it yourself. Call your local power company to have it removed safely.8. If an accident should occur with the power lines, call for qualified emergency help immediately.Antenna ConfigurationsIntegrated Antenna OptionThe AP1572I uses an Integrated Low Profile Dual-Band 2.4-5 GHz Dipole Antenna Array. The antenna contains an array of three dual-band dipole antennas. The three dipole antennas are contained within this single radome, thereby greatly reducing the antenna’s visual footprint, and greatly reducing the possibility of snagging the antenna on the cable bundle, the RF cable, or test cables. Each of thee three](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-48.png)
![2-19Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstalling Antennasdipole antennas is a dual-band antenna, covering both the 2.4 - 2.483 GHz band and the 5.25-5.85 GHz bands. The antenna have a peak gain of about 3 dBi at 2.4 GHz and 5 dBi at 5 GHz. The antenna unit is gray weatherproof radome for outdoor operations.External Antenna Mounting ConfigurationsThe selection of the antenna is determined in the configuration of the product. The 1572E antennas can be mounted on a wall, pole and/or tower mounted. Please refer to the Ordering Guide for a list of supported antennas.The 1572E access point supports a variety of antennas designed for outdoor use with radios operating in the 2.4-GHz and 5-GHz frequency bands. The 1572 supports the external antennas listed in the following sections.Cisco Aironet Dual-Band Omnidirectional Antenna (AIR-ANT2547V-N, AIR-ANT2547VG-N)The Dual-Band Omnidirectional Antenna, referred to as a “stick” antenna, is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz and 5-GHz frequency bands (Figure 2-16). Basic operating features of the antenna are:•Omnidirectional colinear array•Operates in the 2.4 GHz and 5 GHz frequency bands•Gain: –2400–2483 MHz — 4-dBi –5250–5875 MHz — 7-dBiThe antenna is designed to create an omnidirectional broadcast pattern. To achieve this pattern, mount the access point clear of any obstructions to the sides of the radiating element. For detailed information on this antenna, refer to the Cisco Aironet Dual-Band Omnidirectional Antenna (AIR-ANT2547V-N, AIR-ANT2547VG-N) document. Follow all safety precautions when installing the antennas. For information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-18.Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna (AIR-ANT2588P3M-N)The Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in both the 2.4-GHz and 5-GHz frequency bands. This antenna has 8-dBi gain in both bands.For detailed information on this antenna, refer to the Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna (AIR-ANT2588P3M-N) document. Follow all safety precautions when installing the antennas, for information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-18.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-49.png)
![2-20Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstalling AntennasFigure 2-10 Cisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna - Installed Only on Model AIR-CAP1572E-x-K9Note When installing the AIR-ANT2588P3M-N with the Cisco Aironet 1570 Series AP, connect the outermost antenna ports (marked ‘1’ in Figure 2-11) to the AP’s dual band antenna ports.Figure 2-11 Antenna Ports For Connection to AP’s Dual Band Ports3345741352639](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-50.png)
![2-21Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstalling AntennasCisco Aironet 5-GHz 14-dBi 2-Port Directional Antenna (AIR-ANT5114P2M-N)The Cisco Aironet 5-GHz 14-dBi 2-Port Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 5-GHz frequency band. This antenna has 14-dBi in the 5-GHz band.For more information, see the Cisco Aironet 5-GHz 14-dBi Directional Antenna document, at the following URL:http://www.cisco.com/c/en/us/td/docs/wireless/antenna/installation/guide/ant5114p2m-n.html.For detailed information on this antenna, see the Cisco Aironet 5-GHz 14-dBi Directional Antenna (AIR-ANT5114P2M-N) document. Follow all safety precautions when installing the antennas, for information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-18.Figure 2-12 Cisco Aironet 5-GHz 14-dBi Directional Antenna - Installed Only on Models AIR-CAP1572E-x-K9334576](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-51.png)
![2-22Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstalling AntennasCisco Aironet 2.4-GHz 13-dBi 2-Port Directional Antenna (AIR-ANT2413P2M-N)The Cisco Aironet 2.4-GHz 13-dBi 2-Port Directional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has 13-dBi gain in the 2.4-GHz frequency band.For detailed information on this antenna, refer to the Cisco Aironet 2.4-GHz 13-dBi Directional Antenna (AIR-ANT2413P2M-N) document. Follow all safety precautions when installing the antennas, for information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-18.Figure 2-13 Cisco Aironet 2.4-GHz 13-dBi Directional Antenna - Installed Only on Models AIR-CAP1572E-x-K9334576](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-52.png)
![2-23Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstalling AntennasCisco Aironet 2.4-GHz 5-dBi Omnidirectional Antenna (AIR-ANT2450V-N)The Cisco Aironet 2.4-GHz 5-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has a 5-dBi gain in the 2.4-GHz band.For detailed information on this antenna, refer to the document Cisco Aironet 5-dBI Omnidirectional Antenna (AIR-ANT2450V-N). Follow all safety precautions when installing the antennas. For information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-18.Figure 2-14 Cisco Aironet 2.4-GHz 5-dBi Omni Antenna - Installed Only on Model AIR-CAP1572E-x-K9 231297](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-53.png)
![2-24Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstalling AntennasCisco Aironet 2.4-GHz 8-dBi Omnidirectional Antenna (AIR-ANT2480V-N)The Cisco Aironet 2.4-GHz 8-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 2.4-GHz frequency band. This antenna has 8-dBi gain in the 2.4-GHz frequency band.For detailed information on this antenna, refer to the document Cisco Aironet 8-dBi Omnidirectional Antenna (AIR-ANT2480V-N). Follow all safety precautions when installing the antennas, for information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-18.Figure 2-15 Cisco Aironet 2.4-GHz 8-dBi Omni Antenna - Installed Only on Model AIR-CAP1572E-x-K9i230540](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-54.png)
![2-25Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstalling AntennasCisco Aironet 5-GHz 8-dBi Omnidirectional Antenna (AIR-ANT5180V-N)The Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna is designed for outdoor use with Cisco Aironet Outdoor Access Points with radios operating in the 5-GHz frequency band. This antenna has 8-dBi gain in the 5-GHz frequency band.For detailed information on this antenna, refer to the document Cisco Aironet 8-dBi Omnidirectional Antenna (AIR-ANT5180V-N). Follow all safety precautions when installing the antennas, for information on safety, refer to “Safety Precautions when Installing Antennas” section on page 2-18.Figure 2-16 Cisco Aironet 5-GHz 8-dBi Omnidirectional Antenna - Installed Only on Model AIR-CAP1572E-x-K9 Antenna N-Type Connector LocationsThe access point antenna N-type connectors are located on the top and the bottom of model AIR-CAP1572E-x-K9. The N-type connectors support variety of the Cisco Aironet antennas. For detailed information on these antennas, refer to Antenna Configurations, page 2-18. Figure 2-24 shows the antenna port locations viewed from the RF cover side.Installing a Lightning ArrestorOvervoltage transients can be created through lightning static discharges, switch processes, direct contact with power lines, or through earth currents. The Cisco Aironet AIR-ACC245LA-N Lightning Arrestor limits the amplitude and duration of disturbing interference voltages and improves the over voltage resistance of in-line equipment, systems, and components. A lightning arrestor installed according to these mounting instructions balances the voltage potential, thus preventing inductive interference to parallel signal lines within the protected system.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-55.png)
![2-26Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointInstalling AntennasInstallation ConsiderationsCisco recommends that you bulkhead mount the lightning arrestor so it can be installed as a wall-feed through on the wall of the protected space.The importance of obtaining a good ground and bonding connection cannot be overstressed. Consider these points when grounding the lightning arrestor:•Connect the lightning arrestor components directly to the grounding point.•The contact points of the ground connection must be clean and free of dust and moisture.•Tighten threaded contacts to the torque specified by the manufacturer.Installation NotesThis lightning arrestor is designed to be installed between the antenna cable that is attached to an outdoor antenna and the Cisco Aironet wireless device. You can install the lightning arrestor either indoors or outdoors. It can be connected directly to a wireless device having an external N connector. It can also be mounted inline or as a feed-through. Feed-through installations require 5/8 in. (16 mm) hole to accommodate the lightning arrestor.Note This lightning arrestor is part of a lightning arrestor kit. The kit contains a lightning arrestor and a grounding lug.Note When you install the lightning arrestor, follow the regulations or best practices applicable to lightning protection installation in your local area.Installing the Lightning Arrestor OutdoorsIf you install the lightning arrestor outdoors, use the supplied ground lug and a heavy wire (#6 solid copper) to connect it to a good earth ground, such as a ground rod. The connection should be as short as possible.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-56.png)
![2-27Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointGrounding the Access PointFigure 2-17 Lightning Arrestor DetailsCable for the Lightning ArrestorCoaxial cable loses efficiency as the frequency increases, resulting in signal loss. The cable should be kept as short as possible because cable length also determines the amount of signal loss (the longer the run, the greater the loss).Cisco recommends a high-quality, low-loss cable for use with the lightning arrestor.Grounding the Access PointThe access point must be grounded before connecting power.WarningThis equipment must be externally grounded using a customer-supplied ground wire before power is applied. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 366WarningInstallation of the equipment must comply with local and national electrical codes. Statement 1074In all outdoor installations and when powering the access point with AC power, you must follow these instructions to properly ground the case:Step 1 If using insulated 6-AWG copper ground wire, strip the insulation as required for the grounding lug.1Nut 4Unprotected side (to antenna)2Lockwasher 5Protected side (to wireless device)3Ground lug12345346382](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-57.png)
![2-28Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointPowering the Access PointStep 2 Use the appropriate crimping tool to crimp the bare 6-AWG copper ground wire to the supplied grounding lug.Note The grounding lug and hardware used must comply with local and national electrical codes.Step 3 Open the anti-corrosion sealant (supplied), and apply a liberal amount over the metal surface where the ground strap screw holes are located (see Figure 1-5). Step 4 Connect the grounding lug to the access point grounding screw holes (see Figure 1-5) using the supplied two Phillips head screws (M4 x10 mm) with lock washers. Tighten the grounding screw to 22 to 24 lb-in (2.49 to 2.71 Nm). Step 5 If necessary, strip the other end of the ground wire and connect it to a reliable earth ground, such as a grounding rod or an appropriate grounding point on a metal streetlight pole that is grounded (see Figure 2-3).Powering the Access PointWarningInstallation of the equipment must comply with local and national electrical codes. Statement 1074WarningThis equipment must be externally grounded using a customer-supplied ground wire before power is applied. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 366WarningDo not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001The 1572 access point supports these power sources:•DC power – 24- 57 VDC•Power-over-Ethernet (PoE)The 1572 access point can be powered via the PoE input from an in-line power injector or a suitably powered switch port. Depending on the configuration and regulatory domain, the required power for full operation is UPoE. For the 1572E, 802.3at power is sufficient for all regulatory domains and full 2x2 MIMO operation on both 2.4 and 5 GHz radios. Either the AIR-PWRINJ4= or the AIR-PWRINJ1500-2= power injector can be used.For the 1572I, UPoE powered switch port or the AIR-PWRINJ1500-2= power injector is required for full operation of the 3x3 MIMO on the 2.4 GHz radio in the regulatory domains that allow for high 2.4 GHz transmit power (Regulatory domains -A, -D, -F, -K, -N, -Q, -T, -Z). If the 1572I is powered by a PoE+ (802.3at power) switch port or the AIR-PWRINJ4= power injector, then the access point will automatically disable one of the 2.4 GHz transmitters and the radio will operate in 2x3 MIMO mode.Table 2-4 AP 1570 Power Matrix](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-58.png)
![2-29Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointPowering the Access PointCaution Do not place the power injector in an unprotected outdoor environment because water could get into the power injector and cause a short circuit and possible fire.WarningConnect the unit only to DC power source that complies with the Safety Extra-Low Voltage (SELV) requirements in IEC 60950 based safety standards Statement 1033Connecting a 1570 Series Power InjectorThe 1570 Series Access Points support the following power injectors:•AIR-PWRINJ1500-2= — 100-240 VAC input, indoor use only•AIR-PWRINJ4= — 100-240 VAC input, indoor use onlyThe power injector provides (AIR-PWRINJ1500-2=) 56 VDC to the access point over the Ethernet cable and supports a total end-to-end Ethernet cable length of 100 m (328 ft) from the switch to the access point. When your access point is powered by an optional power injector, follow these steps to complete the installation: Step 1 Before applying PoE to the access point, ensure that the access point is grounded (see the “Grounding the Access Point” section on page 2-27).Step 2 Review Figure 2-2 to identify the components needed for the installation.Note The 1500 power injector can only be used in an indoor environment, therefore, the cable from the injector must travel from the protected location to the outside mounted access point.Step 3 Connect a CAT5e or better Ethernet cable from your wired LAN network to the power injector.Model ConfigurationRegulatoryDomainSwitchPower AIR-PWRINJ1500-2= AIR-PWRINJ4=AC/ DC Power Adapter AIR-PWRADPT-1570=1572I 3x3:3 (2.4 GHz)2x3:2 (5 GHz)A, D, K, N, Q, T, ZUPoE Yes YesOne Tx disabled12x3:2 (2.4 GHz)2x3:2 (5 GHz)1. Not user configurable. AP will automatically disable one of the 2.4 GHz Tx if it detects only 802.3at power input.A, D, K, N, Q, T, Z802.3atPoE+Not Applicable Yes Not Applicable3x3:3 (2.4 GHz)2x3:2 (5 GHz)C, E, F, H, M, R, S802.3atPoE+Yes Yes Yes1572E 2x2:2 (2.4 GHz)2x2:2 (5 GHz)All 802.3atPoE+Yes Yes Yes](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-59.png)
![2-30Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointPowering the Access PointWarningTo reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023Note The installer is responsible for ensuring that powering the access point from this type of power injector is allowed by local and/or national safety and telecommunications equipment standards.Tip To forward bridge traffic, add a switch between the power injector and controller. Refer to the Cisco Wireless Mesh Access Points, Design and Deployment Guide, Release 7.0 for more information. Step 4 Ensure that the antennas are connected and that a ground is attached to the access point before you apply power to the access point.Step 5 Connect a shielded outdoor-rated Ethernet (CAT5e or better) cable between the power injector and the PoE-in connector of the access point (see Figure 2-26).Step 6 Connect the Ethernet cable to the access point PoE-In port (see “Connecting an Ethernet Cable to the Access Point” section on page 2-30).Step 7 Continue with What to Do Next, page 2-40.Connecting an Ethernet Cable to the Access Point You need to supply these tools and materials:•Shielded outdoor-rated Ethernet (CAT5e or better) cable with 0.2 to 0.35 in. (0.51 to 0.89 cm) diameter•RJ-45 connector and installation tool•Adjustable Wrench or 28 mm box wrench•Large Phillips or Flat Blade screwdriverTo connect the shielded Ethernet cable to the access point, follow these steps:Step 1 Disconnect power to the power injector, and ensure all power sources to the access point are turned off.WarningThis unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028Step 2 Ensure a 6 AWG ground wire is connected to the access point (see the “Grounding the Access Point” section on page 2-27).Step 3 Use a large Phillips or Flat Blade screw driver to remove the Ethernet connector plug from the access point. Do not discard plug and rubber seal unless you are certain that the port will not have to be re-plugged (see Figure 2-26 for the location).Step 4 Loosen the Thread-Lock sealing nut of the cable gland by turning it counter clockwise, but do not remove it (see Figure 2-18).](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-60.png)
![2-31Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointPowering the Access PointNote Verify that the cable gland has a rubber seal and ensure that it is not damaged.WarningFailure to install the cable gland and rubber gasket properly will cause the cable grip to leak.Figure 2-18 Cable GlandStep 5 Insert the unterminated end of the Ethernet cable through the sealing nut end of the cable gland (see Figure 2-18), and pull several inches of cable through the adapter.Step 6 Install an RJ-45 connector on the unterminated end of the Ethernet cable using your Ethernet cable installation tool.WarningTo reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023WarningWhen installing the RJ-45 connector, ensure that cable gland and the rubber gasket are present and installed properly, to avoid water leakage into the enclosure. See Figure 2-18 and Figure 2-19.Step 7 Carefully insert the RJ-45 cable connector into the Ethernet port opening on the access point, and connect to the internal Ethernet connector (see Figure 2-19). 1Washer (Rubber Gasket) 2Body3Sealing insert 4Clamping claw5Thread-lock sealing nut](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-61.png)
![2-32Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointPowering the Access PointFigure 2-19 Inserting RJ-45 Connector into the Ethernet Port Opening in CaseStep 8 Slide the cable gland with the rubber seal towards the access point, and screw the threaded end of the body into the access point, and hand-tighten.Step 9 Use an adjustable wrench or a 28-mm wrench to tighten the threaded end of the body into the enclosure. Tighten to 15 lb-in.Step 10 Use an adjustable wrench and tighten the thread-lock seal nut to 15 lb-in.Step 11 Ensure that the antennas are connected to the access point before you apply power to the access point.Step 12 Route your Ethernet cable, and cut off any excess cable.Step 13 Install an RJ-45 connector on the unterminated cable end, and insert it into the power injector. For typical installation components, see Figure 2-2.Step 14 Turn on power to the power injector.Connecting a DC Power Cable to the Access Point When powering the access point with DC power, you must ensure that DC power can be conveniently removed from the unit. The power should not be removed by disconnecting the DC power connector on the unit.WarningA readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 10221Ethernet port opening in access point case. 2RJ-45 connector, on shielded outdoor-rated Ethernet (CAT5e or better) cable3Exploded view of the cable gland,on the Ethernet cable.352056123](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-62.png)
![2-33Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointPowering the Access PointWarningConnect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards. Statement 1033To connect a DC power cable, you need to supply these tools and material: •Shielded outdoor-rated DC power cable (minimum 18 AWG) with outside cable diameter of 0.20 to 0.35 inch (0.51 to 0.89 cm).•Adjustable or open-end wrench•Small flat screw driver•Two-pin DC power connector (Cisco supplied)To connect the DC power cable to the access point, follow these steps:Step 1 Before connecting DC power to the access point, ensure that the ground is connected to the access point (see the “Grounding the Access Point” section on page 2-27).Step 2 Turn off all power sources to the access point, including the DC power source.WarningThis unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028Caution When installing DC power to the access point, always connect the access point end of the cable FIRST. When removing the DC power connector, always disconnect the access point end of the cable LAST. Step 3 Use a large Phillips or Flat Blade screw driver to remove the Ethernet connector plug from the access point. Do not discard plug and rubber seal unless you are certain that the port will not have to be re-plugged. (see Figure 2-29 for the location of the DC power connector).Step 4 Loosen the thread-Lock sealing nut of the cable gland by turning it counter clockwise, but do not remove (see Figure 2-20).Note Verify that the cable gland has a rubber seal and ensure that it is not damaged.WarningFailure to install the Cable Gland properly will cause the cable grip to leak.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-63.png)
![2-34Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointPowering the Access PointFigure 2-20 Cable GlandNote The cable gland accepts a cable diameter of 0.20 to 0.35 in. (0.51 to 0.89 cm).Step 5 Insert a bare end of the DC power cable into the rounded end of the cable gland (see Figure 2-20), and pull approximately 6 inches of cable through the adapter.WarningWhen installing the DC power cable, ensure that cable gland and the rubber gasket are present and installed properly, to avoid water leakage into the enclosure. See Figure 2-20 and Figure 2-22.Step 6 Strip the DC cable jacket back about 1 inch to expose the wires and strip the insulation about 3/8 inch (9.5 mm) from each wire.Step 7 Insert each wire into the two-position terminal strip (supplied), and tighten each wire using a 0.1 inch(0.25 cm) flat screw driver (see Figure 2-21).1Washer (Gasket) 2Body3Sealing insert 4Clamping claw5Thread-lock sealing nut](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-64.png)
![2-35Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointPowering the Access PointFigure 2-21 Two-Position Terminal StripStep 8 Insert the two-position terminal strip into the DC power opening in the access point case, and carefully push the terminal strip into the internal connector (see Figure 2-22).Note Ensure that the polarity of the terminal strip properly matches the polarity markings on the enclosure (see Figure 2-23)1Securing screws 3Wire opening for DC + 2Wire opening for ground (DC return)](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-65.png)
![2-36Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointPowering the Access PointFigure 2-22 Inserting the Terminal Strip into the DC Power Opening in the Access Point CaseFigure 2-23 DC Power Opening in the Access Point CaseStep 9 Slide the cable gland with the rubber seal towards the access point, and screw the threaded end of the body into the access point, and hand-tighten.Step 10 Use an adjustable wrench, a 28-mm wrench to tighten the threaded end of the body to 15 lb-in.Step 11 Use an adjustable wrench and tighten the thread-lock seal nut to 15 lb-in.Step 12 Ensure that the antennas are connected to the access point before you apply power to the access point.Step 13 Turn on the DC power at the designated circuits.1DC power opening in access point case. Also see Figure 2-23.2Exploded view of the cable gland on the DC power cable35205712](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-66.png)
![2-37Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointPowering the Access PointConnecting Streetlight AC PowerThe access point can be installed on a streetlight pole and powered from a streetlight outdoor light control using the optional streetlight power tap adapter (AIR-PWR-ST-LT-R3P) and AC/DC power adapter, AIR-PWRADPT-1570=. The AC/DC power adapter is used inline from the street light tap to the 1570 DC connector. The AC power tap only can be used with the AC/DC power adapterCaution The access point can be powered by a light pole twist-lock outdoor light control that provides 100-to 277-VAC 50/60 Hz power. Do not connect to an outdoor light control powered by higher voltages.When powering the access point with AC power other than the streetlight power tap adapter, you must ensure that the following conditions are observed: 1. AC power can be conveniently removed from the unit. The power should not be removed by disconnecting the AC power connector on the unit.WarningA readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 1022Caution Before connecting or disconnecting a power cord, you must remove AC power from the power cord using a suitable service disconnect.2. You must protect any AC power plugs and AC receptacles from water and other outdoor elements. You can use a UL-listed waterproofing enclosure suitable for covering the AC receptacle and AC power plug that supplies power to the unit as described in Article 406 of the NEC.3. When you install the access point outdoors or in a wet or damp location, the AC branch circuit that powers the access point should have ground fault protection (GFCI), as required by Article 210 of the National Electrical Code (NEC).WarningBe very careful when connecting the streetlight adapter to Category 3 pole-top power. If you are not careful, you may electrocute yourself or fall. Statement 363To install an access point on a streetlight pole, follow these steps:Step 1 Before beginning the installation, ensure the AC power to the streetlight pole is turned off.Step 2 Turn off power to the AC power source at the designated circuits.WarningThis unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028Caution For your safety, when connecting the access point AC power connector, always connect the access point end of the cable FIRST. When removing the AC power connector, always disconnect the access point end of the cable LAST.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-67.png)
![2-38Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointPowering the Access PointStep 3 When using the streetlight power tap adapter (AIR-PWR-ST-LT-R3P=), ensure that the access point is mounted within 3 feet (1 m) of the outdoor light control.Step 4 Ensure that a 6-AWG ground wire is attached to the access point (see Figure 2-34) and connected to the streetlight pole (for instructions see Grounding the Access Point, page 2-27).Note Deployment of the AP as shown in the streetlight deployment in Figure 2-34 requires an alternate AP mounting kit. See Mounting the Access Point section for more information.Step 5 Ensure that the streetlight power tap adapter, which uses a 3-pronged LC-10 twist-lock adapter, is placed between the outdoor light control and its fixture (refer to Figure 2-34). The LC-10 twist-lock adapter is designed to be used with LC-10 listed outdoor light controls operating at 100 to 480 VAC, 50 to 60 Hz.Step 6 Disconnect the outdoor light control from its fixture.Step 7 Verify that the voltage available at the fixture is between 100 and 480 VAC, 50 to 60 Hz.Step 8 Turn off power to the fixture at the designated circuits.Caution When installing the streetlight power tap adapter to the access point AC power connector, always connect the access point end of the cable FIRST. When removing the streetlight power tap adapter, always disconnect the access point end of the cable LAST. Note Ensure that your antennas are connected to the access point before you apply power to the access point.Step 9 Connect the streetlight power tap adapter to the access point AC/DC power adapter. See Wiring the Streetlight Power Tap Adapter to the AC/DC Power Adapter.Step 10 Plug the streetlight power tap adapter into the outdoor light control fixture, as shown in Figure 2-34.Step 11 Plug the outdoor light control into the streetlight power tap adapter.Step 12 Ensure that the antennas are connected to the access point before you apply power to the access point.Step 13 Turn on the power to the outdoor light control fixture at the designated circuits.Wiring the Streetlight Power Tap Adapter to the AC/DC Power AdapterThe AC plugs of the streetlight power tap adapter (AIR-PWR-ST-LT-R3P=) and the AC/DC power adapter (AIR-PWRADPT-1570=) are incompatible. Hence, you need to connect the cables to wire them together, using the illustration in Figure 2-24. Ensure that you follow local electrical and safety codes when making and protecting this connection.WarningEnsure that all electrical power is turned off before making this connection.WarningFollow all local wiring and electrical codes when making this connection. Note that the spliced cables may need to be housed in an approved junction box.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-68.png)
![2-39Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointConfiguring the Access PointNote • Cut and remove the AC plugs from each cable. Cut just past strain relief to be sure that the cable is not cut too short.•Ensure that the wiring splice is properly secured and protected.Figure 2-24 Wiring Streetlight Power Tap Adapter to AC/DC Power AdapterConfiguring the Access PointFor information on configuring the access point, see the following documents:•For Lightweight Access Points and Mesh Access Points, see the Cisco Wireless LAN Controller Configuration Guide, which is available at:http://www.cisco.com/en/US/docs/wireless/controller/7.6/configuration/guide/b_cg76.html•For Mesh Access Points, see the Cisco Wireless Mesh Access Points, Design and Deployment Guide, which is available at:http://www.cisco.com/en/US/docs/wireless/technology/mesh/7.6/design/guide/mesh76.html•For Access Points in autonomous mode, see the Cisco Aironet Access Points Configuration Guide for Cisco IOS Software, which is available at:http://www.cisco.com/en/US/docs/wireless/access_point/15_2_4_JB/configuration/guide/scg15.2.4_JB3a_Book.htmlBROWN (L)BLUE (N) GREEN (GND) GREEN (GND) FROM AC/DC ADAPTERREMOVE IEC PLUGFROM AC STREET LIGHT TAP REMOVE CIRCULAR CONNECTOR BLACK (L)WHITE (N)352647](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-69.png)
![2-40Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 2 Installing the Access PointWhat to Do NextWhat to Do NextWhen you power up a MAP that is not connected to a wired Ethernet, fiber-optic, or cable network to the controller, the access point uses the Cisco Adaptive Wireless Path Protocol (AWPP) to bind to another mesh access point (MAP) with the best path to a root access point (RAP) connected to the wired network to a controller. The access point sends a discovery request when powered up. If you have configured the access point in the controller correctly, the controller sends back a discovery response to the access point. When that happens, the access point sends out a join request to the controller, and the controller responds with a join confirmation response. Then the access point establishes a Control And Provisioning of Wireless Access Points (CAPWAP) connection to the controller and gets the shared secret configured on the controller. Refer to the Cisco Wireless LAN Controller Configuration Guide for more information on configuring, monitoring, and operating your access points.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-70.png)
![CHAPTER 3-1Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-013TroubleshootingThis chapter provides troubleshooting procedures for basic problems with the access point. For the most up-to-date, detailed troubleshooting information, refer to the Cisco Technical Support and Documentation website at the following URL:http://www.cisco.com/cisco/web/support/index.htmlSections in this chapter include:•Guidelines for Using the Access Points, page 3-2•Controller MAC Filter List, page 3-3•Using DHCP Option 43, page 3-3•Monitoring the Access Point LEDs, page 3-4•Verifying Controller Association, page 3-5•Changing the Bridge Group Name, page 3-6•Access Point Power Injector, page 3-6•Access Point Power Injector, page 3-6•Using the Reset Button, page 3-8](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-71.png)
![3-2Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 3 TroubleshootingGuidelines for Using the Access PointsGuidelines for Using the Access PointsYou should keep these guidelines in mind when you use the access points:•The access point only supports Layer 3 CAPWAP communications with the controllers.In Layer 3 operation, the access point and the controller can be on the same or different subnets. The access point communicates with the controller using standard IP packets. A Layer 3 access point on a different subnet than the controller requires a DHCP server on the access point subnet and a route to the controller. The route to the controller must have destination UDP ports 12222 and 12223 open for CAPWAP communications. The route to the primary, secondary, and tertiary controllers must allow IP packet fragments. •Before deploying your access points, ensure that the following has been done:–Your controllers are connected to switch ports that are configured as trunk ports. –Your access points are connected to switch ports that are configured as untagged access ports. –A DHCP server is reachable by your access points and has been configured with Option 43. Option 43 provides the IP addresses of the management interfaces of your controllers. Typically, a DHCP server can be configured on a Cisco switch.–Optionally, a DNS server can be configured to enable CISCO-CAPWAP-CONTROLLER. Use local domain to resolve to the IP address of the management interface of your controller.–Your controllers are configured and reachable by the access points.–Your controllers are configured with the access point MAC addresses and the MAC filter list is enabled.–Your switch must forward DHCP requests.•After the access points are associated to the controller, you should change the bridge group name (BGN) from the default value. With the default BGN, the mesh access points (MAPs) can potentially try to connect with other mesh networks and slow down the convergence of the network.Important NotesConvergence DelaysDuring deployment, the access points can experience convergence delays due to various causes. The following list identifies some operating conditions that can cause convergence delays:•A root access point (RAP) attempts to connect to a controller using any of the wired ports (cable, fiber-optic, PoE-in). If the wired ports are operational, the RAP can potentially spend several minutes on each port prior to connecting to a controller. •If a RAP is unable to connect to a controller over the wired ports, it attempts to connect using the wireless network. This results in additional delays when multiple potential wireless paths are available.•If a MAP is unable to connect to a RAP using a wireless connection, it then attempts to connect using any available wired port. The access point can potentially spend several minutes for each connection method, before attempting the wireless network again.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-72.png)
![3-3Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 3 TroubleshootingController MAC Filter ListBridge LoopThe access point supports packet bridging between wired and wireless network connections. The same network must never be connected to multiple wired ports on an access point or on two bridged access points. A bridge loop causes network routing problems.Controller DHCP ServerThe controller DHCP server only assigns IP addresses to lightweight access points and wireless clients associated to an access point. It does not assign an IP address to other devices, including Ethernet bridging clients on the mesh access points.MAP Data TrafficIf the signal on the access point backhaul channel has a high signal-to-noise ratio, it is possible for a MAP to connect to the controller, via parent node, but not be able to pass data traffic, such as pinging the access point. This can occur because the default data rate for backhaul control packets is set to 6 Mb/s, and the backhaul data rate set to auto by the user. Controller MAC Filter ListBefore activating your access point, you must ensure that the access point MAC address has been added to the controller MAC filter list and that Mac Filter List is enabled.Note The access point MAC address and barcode is located on the bottom of the unit. When two MAC addresses are shown, use the top MAC address.To view the MAC addresses added to the controller MAC filter list, you can use the controller CLI or the controller GUI:•Controller CLI—Use the show macfilter summary controller CLI command to view the MAC addresses added to the controller filter list.•Controller GUI—Log into your controller web interface using a web browser, and choose SECURITY > AAA > MAC Filtering to view the MAC addresses added to the controller filter list.Using DHCP Option 43You can use DHCP Option 43 to provide a list of controller IP addresses to the access points, enabling the access point to find and join a controller. Refer to the product documentation for your DHCP server for instructions on configuring DHCP Option 43. For additional information, refer to the “Configuring DHCP Option 43” section on page F-1.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-73.png)
![3-4Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 3 TroubleshootingMonitoring the Access Point LEDsMonitoring the Access Point LEDsIf your access point is not working properly, look at the LEDs on the bottom of the unit. You can use them to quickly assess the status of the unit. Note It is expected that there will be small variations in LED color intensity and hue from unit to unit. This is within the normal range of the LED manufacturer specifications and is not a defect.The access point LED signals are listed in Table 3-1.Table 3-1 Access Point LED Signals LED Message TypeColor MeaningBoot loader status sequenceBlinking Green Boot loader status sequence:•DRAM memory test in progress•DRAM memory test OK•Board initialization in progress•Initializing FLASH file system•FLASH memory test OK•Initializing Ethernet•Ethernet OK•Starting Cisco IOS•Initialization successfulBoot loader warningsBlinking Amber Configuration recovery is in progress (the MODE button has been pushed for 2-3 seconds)Solid Red There is an Ethernet failure or an image recovery (the MODE button has been pushed for 20-30 seconds)Blinking Green An image recovery is in progress (the MODE button has been released)Boot loader errorsSolid Red There has been a DRAM memory test failureBlinking Red and Amber There has been a FLASH file system failureBlinking Red and Off This sequence may indicate any of the following:•Environment variable failure•Bad MAC address•Ethernet failure during image recovery•Boot environment failure•No Cisco image file•Boot failureCisco IOS errorsSolid Red There has been a software failure; a disconnect then reconnect of the unit power may resolve the issueCycling through Red, Green, Amber and OffThis is a general warning of insufficient inline power.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-74.png)
![3-5Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 3 TroubleshootingVerifying Controller AssociationVerifying Controller AssociationTo verify that your access point is associated to the controller, follow these steps:Step 1 Log into your controller web interface using a web browser.You can also use the controller CLI show ap summary command from the controller console port.Step 2 Click Wireless, and verify that your access point MAC address is listed under Ethernet MAC.Step 3 Log out of the controller, and close your web browser.Association statusChirping (short blips) GreenThis status indicates a normal operating condition. The unit is joined to a controller, but no wireless client is associated with it.Solid Green Normal operating condition with at least one wireless client associated with the unitOperating StatusBlinking Amber A software upgrade is in progressCycling through Green, Red and AmberDiscovery/join process is in progressRapidly cycling through Red, Green, Amber and OffThis status indicates that the Access Point location command has been invoked.Blinking Red This status indicates that an Ethernet link is not operationalAlignment ModeColor Signal Level (dBm)Solid Green > –44Fast blinking Green –47 to –44Medium blinking Green –50 to –47Solid Amber –53 to –50Fast blinking Amber –57 to –53Medium blinking Amber –60 to –57Slow blinking Amber –63 to –60Slow blinking Red –66 to –63Medium blinking Red –69 to –66Fast blinking Red –72 to –69Solid Red –75 to –72Off < –75LED Message TypeColor Meaning](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-75.png)
![3-6Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 3 TroubleshootingChanging the Bridge Group NameChanging the Bridge Group NameThe bridge group name (BGN) controls the association of the access points to a RAP. BGNs can be used to logically group the radios to avoid different networks on the same channel from communicating with each other. This setting is also useful if you have more than one RAP in your network in the same area.If you have two RAPs in your network in the same area (for more capacity), we recommend that you configure the two RAPs with different BGNs and on different channels.The BGN is a string of ten characters maximum. A factory-set bridge group name (NULL VALUE) is assigned during manufacturing. It is not visible to you, but allows new access point radios to join a network of new access points. The BGN can be reconfigured from the Controller CLI and GUI. After configuring the BGN, the access point reboots.After the access points are deployed and associated to the controller, the BGN should be changed from the default value to prevent the MAPs from attempting to associate to other mesh networks.The BGN should be configured very carefully on a live network. You should always start with the most distant access point (last node) from the RAP and move towards the RAP. If you start configuring the BGN in a different location, then the access points beyond this point (farther away) are dropped, as they have a different BGN. To configure the BGN for the access points using the controller GUI, follow these steps:Step 1 Log into your controller using a web browser.Step 2 Click Wireless. When access points associates to the controller, the access point name appears in the AP Name list.Step 3 Click on an access point name. Step 4 Find the Mesh Information section, and enter the new BGN in the Bridge Group Name field.Step 5 Click Apply.Step 6 Repeat Steps 2 through 5 for each access point.Step 7 Log out from your controller, and close your web browser.Access Point Power InjectorThe power injector (AIR-PWRINJ1500-2=) has three LEDs on the front end of the case (see Figure 3-1). For detailed information on the power injector, see the Cisco Aironet 1550 Series Outdoor Access Point Power Injector Installation Instructions.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-76.png)
![3-7Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 3 TroubleshootingAccess Point Power InjectorFigure 3-1 Power Injector Connectors and LEDs1Mounting tabs 4AC POWER LED2AP POWER LED 5TO AP—Ethernet connector (RJ-45) to access point (10/100/1000BASE-T)3FAULT LED 6TO SWITCH—Ethernet connector (RJ-45) to switch (10/100/1000BASE-T)211485231484112 3 4 5 6](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-77.png)
![3-8Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 3 TroubleshootingUsing the Reset ButtonMonitoring the Power Injector LEDsYou can use the power injector LEDs to check the power injector status. The LEDs provide the following status information:•AP POWER—Turns solid green after successful discovery; indicates that power injector is supplying power to the access point.•FAULT—Turns solid red when a fault occurs during discovery mode or power-up. Check Ethernet cables and connections before contacting your support organization for assistance.•AC POWER—Turns solid green when power injector is receiving AC power and is ready to provide power to the access point.Using the Reset ButtonThe access point has a reset button located on the left side of the enclosure, inside the Console-Reset port, under the hex-shaped sealed plug.Caution Inspect the seal of the plug and properly tighten it every time the plug is removed and replaced. Tighten the plug to 15 lbf-in.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-78.png)
![3-9Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 3 TroubleshootingUsing the Reset ButtonResetting the Access PointUsing the Reset button you can either return the AP back to its default factory-shipped configuration or download the latest software image from the default TFTP servers.To use the Reset button:Step 1 Using a wrench, remove the hex-shaped plug from the Console-Reset port. Do not loose the seal around the plug.Step 2 To press and hold the Reset button, use a straightened paperclip or a small screwdriver or a pen.•To reset the AP back to its default factory-shipped configuration, during power cycle, press and hold the Reset button (for about 2 to 3 seconds) until the LED blinks amber.•To download the software image (ap1g3-k9w7-tar.default) from the default TFTP servers (servers with IP address in the range of 10.0.0.2 to 10.0.0.30), during power cycle, press and hold the Reset button (for about 20 to 30 seconds) until the LED turns red.Step 3 Inspect the hex-shaped plug attached to the lanyard for any damage to the sealing face and the gasket. If the gasket has any signs of damage, it should be replaced to avoid water leakage into the unit.Step 4 Replace the hex-shaped plug back and tighten it to 15 lbf-in.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-79.png)
![3-10Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Chapter 3 TroubleshootingUsing the Reset Button](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-80.png)
![A-1Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01APPENDIX ATranslated Safety WarningsFor translated safety warnings, refer to the safety warning document that shipped with your access point or that is available on Cisco.com. To browse to the document on Cisco.com, follow these steps:Step 1 Click this link and go to the Cisco Wireless documentation home page:http://www.cisco.com/en/US/products/hw/wireless/index.htmlStep 2 Click Support and the Support and Documentation page displays.Step 3 Click Wireless in the Find Product Support column.Step 4 Click 1570.Step 5 Click Install and Upgrade.Step 6 Click Install and Upgrade Guides.Step 7 Click Translated Safety Warnings for Cisco Aironet 1570 Series Outdoor Access Points.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-81.png)
![A-2Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix A Translated Safety Warnings](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-82.png)
![B-1Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01APPENDIX BDeclarations of Conformity and Regulatory InformationThis appendix provides declarations of conformity and regulatory information for the Cisco Aironet 1570 Series Outdoor Access Points.This appendix contains the following sections:•Manufacturers Federal Communication Commission Declaration of Conformity Statement, page B-2•Industry Canada, page B-3•European Community, Switzerland, Norway, Iceland, and Liechtenstein, page B-5•Declaration of Conformity for RF Exposure, page B-8•Guidelines for Operating Cisco Aironet Access Points in Japan, page B-10•VCCI Statement for Japan, page B-11•Administrative Rules for Cisco Aironet Access Points in Taiwan, page B-11•EU Declaration of Conformity, page B-13](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-83.png)
![B-2Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationManufacturers Federal Communication Commission Declaration of Conformity StatementManufacturers Federal Communication Commission Declaration of Conformity StatementModels: FCC Certification number: Manufacturer:Cisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAThis device complies with Part 15 rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:•Reorient or relocate the receiving antenna.•Increase separation between the equipment and receiver.•Connect the equipment to an outlet on a circuit different from which the receiver is connected.•Consult the dealer or an experienced radio/TV technician.Tested To ComplyWith FCC StandardsFOR HOME OR OFFICE USEAIR-AP1572EAC-B-K9AIR-AP1572EC1-B-K9AIR-AP1572EC2-B-K9AIR-AP1572IC1-B-K9AIR-AP1572IC2-B-K9LDK102093P](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-84.png)
![B-3Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationIndustry CanadaCaution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using Cisco-supplied antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device.Caution To meet regulatory restrictions, the access point must be professionally installed.Industry CanadaModels: IC Certification Number: Canadian Compliance StatementThis Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.Cet appareil numerique de la classe A respecte les exigences du Reglement sur le material broilleur du Canada.This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.Cisco Aironet Access Points are certified to the requirements of RSS-210. The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office.This device has been designed to operate with antennas having a maximum gain of 13 dBi for 2.4 GHz and 14 dBi for 5 GHz. Antennas having a gain greater are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.AIR-AP1572EAC-A-K9AIR-AP1572EC1-A-K9AIR-AP1572EC2-A-K9AIR-AP1572IC1-A-K9AIR-AP1572IC2-A-K92461B-LDK102093P](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-85.png)
![B-4Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationDeclaration of Conformity for RF ExposureTo reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication.Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.Users are advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.Les utilisateurs êtes avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-ELDeclaration of Conformity for RF ExposureThis access point product has been found to be compliant to the requirements set forth in CFR 47Section 1.1307 addressing RF Exposure from radio frequency devices as defined in Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. Antennas that have 8 dBi to 14 dBi gain should be located at a minimum of 19.7 inches (50 cm) or more from the body of all persons. Antennas that have less than 8 dBi gain should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons.This access point is also compliant to EN 50835 for RF exposure.Dual Band Omni Max Antenna Gain 7dBiSingle Band Omni Max Antenna Gain 8 dBiSingle Band Directional Max Antenna Gain 14dBiDual Band Directional Max Antenna Gain 8 dBiAntenna Impedance in all cases is 50 Ohms](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-86.png)
![B-5Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationEuropean Community, Switzerland, Norway, Iceland, and LiechtensteinEuropean Community, Switzerland, Norway, Iceland, and LiechtensteinAccess Point Models:AIR-AP1572EAC-E-K9AIR-AP1572EC3-E-K9AIR-AP1572IC3-E-K9Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EECThis declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by Cisco Systems. The use of software or firmware not provided and supported by Cisco Systems may result in the equipment no longer being compliant with the regulatory requirements.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-87.png)
![B-6Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationDeclaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-88.png)
![B-7Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationDeclaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EECThe following standards were applied:EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1Health & Safety—EN60950-1: 2005; EN 50385: 2002Radio—EN 300 328 v 1.7.1; EN 301.893 v 1.5.1The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive 1999/5/EC has been followed.This device also conforms to the EMC requirements of the Medical Devices Directive 93/42/EEC.Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance.The product carries the CE Mark:](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-89.png)
![B-8Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationDeclaration of Conformity for RF ExposureDeclaration of Conformity for RF ExposureThe following is the declaration of conformity for RF exposure for the United States, Canada, European Union and Australia.United StatesThis system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (AmericanNational Standards Institute) limits. The evaluation was based on ANSI C 95.1 and FCC OET Bulletin65C rev 01.01. To maintain compliance, the minimum separation distance for antennas that have 8 dBi to 14 dBi gain, is 19.7 inches (50 cm) from general bystanders. The minimum separation distance from antennas that have less than 8 dBi gain to general bystanders is 7.9 inches (20 cm).CanadaThis system has been evaluated for RF exposure for Humans in reference to ANSI C 95.1 (American National Standards Institute) limits. The evaluation was based on RSS-102 Rev 2. To maintain compliance, the minimum separation distance for antennas that have 8 dBi to 14 dBi gain, is 20 inches (50 cm) from general bystanders. The minimum separation distance from antennas that have less than 8 dBi gain to general bystanders is 10 inches (25 cm).Ce système a été évalué pour l'exposition aux RF pour les humains en référence à la norme ANSI C 95.1 (American National Standards Institute) limites. L'évaluation a été basée sur RSS-102 Rev 2. La distance minimale de séparation de l'antenne de toute personne est de 10 "(25 cm) pour les gains d'antenne jusqu'à 8 dBi et 20" (50 cm) pour les gains d'antenne de 14 dbi pour assurer le respect.European UnionThis system has been evaluated for RF exposure for Humans in reference to the ICNIRP (InternationalCommission on Non-Ionizing Radiation Protection) limits. The evaluation was based on the EN 50385Product Standard to Demonstrate Compliance of Radio Base stations and Fixed Terminals for WirelessTelecommunications Systems with basic restrictions or reference levels related to Human Exposure toRadio Frequency Electromagnetic Fields from 300 MHz to 40 GHz. To maintain compliance, the minimum separation distance for antennas that have 8 dBi to 14 dBi gain, is 19.7 inches (50 cm) from general bystanders. The minimum separation distance from antennas that have less than 8 dBi gain to general bystanders is 7.9 inches (20 cm).AustraliaThis system has been evaluated for RF exposure for Humans as referenced in the Australian RadiationProtection standard and has been evaluated to the ICNIRP (International Commission on Non-Ionizing](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-90.png)
![B-9Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationDeclaration of Conformity for RF ExposureRadiation Protection) limits. To maintain compliance, the minimum separation distance for antennas that have 8 dBi to 14 dBi gain, is 19.7 inches (50 cm) from general bystanders. The minimum separation distance from antennas that have less than 8 dBi gain to general bystanders is 7.9 inches (20 cm).](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-91.png)
![B-10Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationGuidelines for Operating Cisco Aironet Access Points in JapanGuidelines for Operating Cisco Aironet Access Points in JapanThis section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English.Lightweight Access Point Model:AIR-AP1572EAC-Q-K9AIR-AP1572EC4-Q-K9AIR-AP1572IC4-Q-K9Japanese TranslationEnglish TranslationThis equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines.1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity.2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions.3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below.Contact Number: 03-6434-650003-6434-650043768](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-92.png)
![B-11Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationAdministrative Rules for Cisco Aironet Access Points in TaiwanVCCI Statement for JapanAdministrative Rules for Cisco Aironet Access Points in TaiwanThis section provides administrative rules for operating Cisco Aironet Access Points in Taiwan. The rules are provided in both Chinese and English.Chinese TranslationWarningThis is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-93.png)
![B-12Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationAdministrative Rules for Cisco Aironet Access Points in TaiwanEnglish TranslationAdministrative Rules for Low-power Radio-Frequency DevicesArticle 12For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions.Article 14The operation of the low-power radio-frequency devices is subject to the conditions that no harmful interference is caused to aviation safety and authorized radio station; and if interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear.The authorized radio station means a radio-communication service operating in accordance with the Communication Act. The operation of the low-power radio-frequency devices is subject to the interference caused by the operation of an authorized radio station, by another intentional or unintentional radiator, by industrial, scientific and medical (ISM) equipment, or by an incidental radiator. Chinese TranslationEnglish TranslationLow-power Radio-frequency Devices Technical Specifications4.7Unlicensed National Information Infrastructure4.7.6The U-NII devices shall accept any interference from legal communications and shall not interfere the legal communications. If interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-94.png)
![B-13Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationOperation of Cisco Aironet Access Points in Brazil4.7.7Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the user manual.Statement 371—Power Cable and AC AdapterEnglish TranslationWhen installing the product, please use the provided or designated connection cables/power cables/AC adapters. Using any other cables/adapters could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to CISCO-designated products.EU Declaration of ConformityAll the Declaration of Conformity statements related to this product can be found at the following location:http://www.ciscofax.comOperation of Cisco Aironet Access Points in BrazilThis section contains special information for operation of Cisco Aironet access points in Brazil.Access Point ModelsAIR-AP1572EAC-Z-K9AIR-AP1572EC1-Z-K9AIR-AP1572EC2-Z-K9AIR-AP1572EC3-Z-K9AIR-AP1572IC1-Z-K9AIR-AP1572IC2-Z-K9](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-95.png)
![B-14Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix B Declarations of Conformity and Regulatory InformationOperation of Cisco Aironet Access Points in BrazilAIR-AP1572IC3-Z-K9Regulatory InformationFigure B-1 contains Brazil regulatory information for the access point models identified in the previous section.Figure B-1 Brazil Regulatory InformationPortuguese TranslationEste equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.English TranslationThis equipment operates on a secondary basis and consequently must accept harmful interference, including interference from stations of the same kind. This equipment may not cause harmful interference to systems operating on a primary basis.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-96.png)
![C-1Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01APPENDIX CChannels and Power LevelsFor channel and maximum power level settings, refer to the Channels and Maximum Power Settings for Cisco Aironet Lightweight Access Points and Bridges document available on the Cisco Wireless documentation page of Cisco.com.To browse to the document, follow these steps:Step 1 Click this link and go to the Cisco Wireless documentation home page:http://www.cisco.com/en/US/products/hw/wireless/index.htmlStep 2 Click Support. The Support and Documentation page displays.Step 3 Click WirelessStep 4 Click 1570.Step 5 Click Install and Upgrade.Step 6 Click Install and Upgrade Guides.Step 7 Click Channels and Maximum Power Settings for Cisco 1570 Series Outdoor Access Points document.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-97.png)
![C-2Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix C Channels and Power Levels](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-98.png)
![D-1Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01APPENDIX DAccess Point Data SheetThe detailed technical specifications for the Cisco Aironet 1570 Series Outdoor Access Points are available at the following URL:You can also download a copy of the Cisco Aironet 1570 Series Outdoor Access Point Data Sheet from the above URL for offline use.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-99.png)
![D-2Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix D Access Point Data Sheet](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-100.png)
![E-1Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01APPENDIX EAccess Point Pinouts This appendix describes the pin signals of the access point Ethernet connectors, and the power injector input and output connectors. Table E-1 describes the pin signals of the access point LAN connector Table E-2 describes the pin signals for the access point PoE-in Ethernet connector. The Pinouts given in this table are applicable to AIR-POWERINJ1500. Not all PoE power sources follow these pinouts.Table E-1 Access Point LAN Connector Pinouts Pin Number Signal Name1 Ethernet signal pair (10/100/1000BASE-T)23 Ethernet signal pair (10/100/1000BASE-T)64 Ethernet signal pair (10/100/1000BASE-T)57 Ethernet signal pair (10/100/1000BASE-T)8Shield Chassis groundTable E-2 Access Point PoE-In Ethernet Connector Pinouts for AIR-POWERINJ1500Pin Number Signal Name1 Ethernet signal pair (10/100/1000BASE-T) and DC return23 Ethernet signal pair (10/100/1000BASE-T) and DC (+)64 Ethernet signal pair (1000BASE-T) and DC (+)5](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-101.png)
![E-2Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix E Access Point PinoutsTable E-3 describes the pin signals for the power injector input connector (To Switch).Table E-4 describes the RJ-45 pin signals for the power injector output connector (To AP). The Pinouts given in this table are applicable to AIR-POWERINJ1500. Not all PoE power sources follow these pinouts.7 Ethernet signal pair (1000BASE-T) and DC return8Shield Chassis groundTable E-2 Access Point PoE-In Ethernet Connector Pinouts for AIR-POWERINJ1500Pin Number Signal NameTable E-3 Power Injector Input Connector (To Switch) PinoutsPin Number Signal Name1 Ethernet signal pair (10/100/1000BASE-T)23 Ethernet signal pair 10/100/1000BASE-T)64 Ethernet signal pair (1000BASE-T)57 Ethernet signal pair (1000BASE-T)8Shield Chassis groundTable E-4 Power Injector AIR-POWERINJ1500 Output Connector (To AP) PinoutsPin Number Signal Name1 Ethernet signal pair (10/100/1000BASE-T) and DC return23 Ethernet signal pair (10/100/1000BASE-T) and DC (+)64 Ethernet signal pair (1000BASE-T) and DC (+)57 Ethernet signal pair (1000BASE-T) and DC return8Shield Chassis ground](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-102.png)
![F-1Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01APPENDIX FConfiguring DHCP Option 43This appendix describes the steps needed to configure DHCP Option 43 on a DHCP server, such as a Cisco Catalyst 3750 series switch, for use with Cisco Aironet Access Points. This appendix contains these sections:•Overview, page F-2•Configuring Option 43 for 1000, 1500, and 1570 Series Access Points, page F-3•Configuring Option 43 for 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1570 Series Access Points, page F-4](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-103.png)
![F-2Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix F Configuring DHCP Option 43OverviewOverviewThis section contains a DHCP Option 43 configuration example on a DHCP server for use with Cisco Aironet Access Points. For other DHCP server implementations, consult DHCP server product documentation for configuring DHCP Option 43. In Option 43, use the IP address of the controller management interface.Note DHCP Option 43 is limited to one access point type per DHCP pool. You must configure a separate DHCP pool for each access point type.Cisco Aironet 1000, 1500, 1532 access points use a comma-separated string format for DHCP Option 43. Other Cisco Aironet access points use the type-length-value (TLV) format for DHCP Option 43. DHCP servers must be programmed to return the option based on the access point DHCP Vendor Class Identifier (VCI) string (DHCP Option 60). The VCI strings for Cisco access points that can operate in lightweight mode are listed in Table F-1. The following is the format of the TLV block for 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1532 access points: •Type: 0xf1 (decimal 241) •Length: Number of controller IP addresses * 4 •Value: List of WLC management interfaces Table F-1 Lightweight Access Point VCI StringsAccess Point Vendor Class Identifier (VCI)Cisco Aironet 1000 series Airespace.AP1200Cisco Aironet 1100 series Cisco AP c1100Cisco Aironet 1130 series Cisco AP c1130Cisco Aironet 1200 series Cisco AP c1200Cisco Aironet 1240 series Cisco AP c1240Cisco Aironet 1250 series Cisco AP c1250Cisco Aironet 1300 series Cisco AP c1300Cisco Aironet 1500 series Cisco AP c150011. For controller release 4.1 or later.Cisco AP.OAP15002, Cisco AP.LAP15102, orCisco AP.LAP15052 2. For controller release 4.0, the VCI depends on the model.Airespace.AP120033. For controller release 3.2.Cisco Aironet 1520 series Cisco AP c1520Cisco Aironet 1570 series Cisco AP c1570](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-104.png)
![F-3Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix F Configuring DHCP Option 43Configuring Option 43 for 1000, 1500, and 1570 Series Access PointsConfiguring Option 43 for 1000, 1500, and 1570 Series Access Points To configure DHCP Option 43 for Cisco 1000, 1500, and 1570 series access points in the embedded Cisco IOS DHCP server, follow these steps: Step 1 Enter configuration mode at the Cisco IOS command line interface (CLI). Step 2 Create the DHCP pool, including the necessary parameters such as default router and name server. These commands are used to create a DHCP pool: ip dhcp pool pool name network IP Network Netmask default-router Default router dns-server DNS ServerWhere:pool name is the name of the DHCP pool, such as AP1000IP Network is the network IP address where the controller resides, such as 10.0.15.1Netmask is the subnet mask, such as 255.255.255.0Default router is the IP address of the default router, such as 10.0.0.1DNS Server is the IP address of the DNS server, such as 10.0.10.2Step 3 Add the Option 60 line for access point using the following syntax: option 60 ascii “VCI string” For the VCI string, use the value from Table F-1. The quotation marks must be included. Step 4 Add the Option 43 line using the following syntax: option 43 ascii “Comma Separated IP Address List” For example, if you are configuring Option 43 for Cisco 1000, 1500, or 1500 series access points using the controller IP addresses 10.126.126.2 and 10.127.127.2, add the following line to the DHCP pool in the Cisco IOS CLI: option 43 ascii “10.126.126.2,10.127.127.2” The quotation marks must be included.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-105.png)
![F-4Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Appendix F Configuring DHCP Option 43Configuring Option 43 for 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1570 Series Access PointsConfiguring Option 43 for 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1570 Series Access PointsTo configure DHCP Option 43 for Cisco Aironet 1100, 1130, 1200, 1240, 1250, 1300, 1520, and 1570 series access points in the embedded Cisco IOS DHCP server, follow these steps: Step 1 Enter configuration mode at the Cisco IOS CLI. Step 2 Create the DHCP pool, including the necessary parameters such as default router and name server. The commands used to create a DHCP pool are as follows: ip dhcp pool pool name network IP Network Netmask default-router Default router dns-server DNS Server Where:pool name is the name of the DHCP pool, such as AP1570IP Network is the network IP address where the controller resides, such as 10.0.15.1Netmask is the subnet mask, such as 255.255.255.0Default router is the IP address of the default router, such as 10.0.0.1DNS Server is the IP address of the DNS server, such as 10.0.10.2Step 3 Add the Option 60 line using the following syntax: option 60 ascii “VCI string” For the VCI string, use the value from Table F-1. The quotation marks must be included. Step 4 Add the Option 43 line using the following syntax: option 43 hex hex string The hex string is assembled by concatenating the TLV values shown below: Type + Length + Va l u e Type is always f1(hex). Length is the number of controller management IP addresses times 4 in hex. Va l u e is the IP address of the controller listed sequentially in hex. For example, suppose that there are two controllers with management interface IP addresses, 10.126.126.2 and 10.127.127.2. The type is f1(hex). The length is 2 * 4 = 8 = 08 (hex). The IP addresses translate to 0a7e7e02 and 0a7f7f02. Assembling the string then yields f1080a7e7e020a7f7f02. The resulting Cisco IOS command added to the DHCP scope is listed below: option 43 hex f1080a7e7e020a7f7f02](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-106.png)
![GL-1Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01 GLOSSARY802.3af/at The IEEE standard that describes a mechanism for Power over Ethernet (PoE). The standard provides the capability to deliver both power and data over standard Ethernet cabling.802.11 The IEEE standard that specifies carrier sense media access control and physical layer specifications for 1- and 2-megabit-per-second (Mb/s) wireless LANs operating in the 2.4-GHz band.802.11a The IEEE standard that specifies carrier sense media access control and physical layer specifications for wireless LANs operating in the 5-GHz frequency band.802.11b The IEEE standard that specifies carrier sense media access control and physical layer specifications for 5.5- and 11-Mb/s wireless LANs operating in the 2.4-GHz frequency band.802.11g The IEEE standard that specifies carrier sense media access control and physical layer specifications for 6, 9, 12, 18, 24, 36, 48, and 54 Mb/s wireless LANs operating in the 2.4-GHz frequency band.802.11n 802.11n is a specification for wireless LAN (WLAN) communications. An addition to the 802.11 family of standards, 802.11n increases network speed and reliability and extends the operating distance of wireless networks. Raw data throughput is expected to reach as much as 600 Mb/s, or more than 10 times the throughput of 802.11gAaccess point A wireless LAN data transceiver that uses radio waves to connect a wired network with wireless stations.ad hoc network A wireless network composed of stations without access points.antenna gain The gain of an antenna is a measure of the antenna ability to direct or focus radio energy over a region of space. High gain antennas have a more focused radiation pattern in a specific direction.associated A station is configured properly to allow it to wirelessly communicate with an access point.AWPP Adaptive Wireless Path Protocol.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-107.png)
![GlossaryGL-2Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-108.png)
![GlossaryGL-3Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Bbeacon A wireless LAN packet that signals the availability and presence of the wireless device. Beacon packets are sent by access points and base stations; however, client radio cards send beacons when operating in computer to computer (Ad Hoc) mode.BOOTP Boot Protocol. A protocol used for the static assignment of IP addresses to devices on the network.BPSK Binary phase shift keying is a modulation technique used by IEEE 802.11b-compliant wireless LANs for transmission at 1 Mb/s.broadcast packet A single data message (packet) sent to all addresses on the same subnet.CCAPWAP Control And Provisioning of Wireless Access PointsCCK Complementary Code Keying. A modulation technique used by IEEE 802.11b-compliant wireless LANs for transmission at 5.5 and 11 Mb/s.CCKM Cisco Centralized Key Management. Using CCKM, authenticated client devices can roam from one access point to another without any perceptible delay during reassociation. An access point on your network provides wireless domain services (WDS) and creates a cache of security credentials for CCKM-enabled client devices on the subnet. The WDS access point's cache of credentials dramatically reduces the time required for reassociation when a CCKM-enabled client device roams to a new access point.cell The area of radio range or coverage in which the wireless devices can communicate with the base station. The size of the cell depends upon the speed of the transmission, the type of antenna used, and the physical environment, as well as other factors.client A radio device that uses the services of an access point to communicate wirelessly with other devices on a local area network.CSMA Carrier sense multiple access. A wireless LAN media access method specified by the IEEE 802.11 specification.Ddata rates The range of data transmission rates supported by a device. Data rates are measured in megabits per second (Mb/s).dBi A ratio of decibels to an isotropic antenna that is commonly used to measure antenna gain. The greater the dBi value, the higher the gain, and the more acute the angle of coverage.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-109.png)
![GlossaryGL-4Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01DFS Dynamic Frequency Selection. In some regulatory domains, 5-GHz radios are required to use DFS to avoid interfering with radar signals.DHCP Dynamic host configuration protocol. A protocol available with many operating systems that automatically issues IP addresses within a specified range to devices on the network. The device retains the assigned address for a specific administrator-defined period.domain name The text name that refers to a grouping of networks or network resources based on organization-type or geography; for example: name.com—commercial; name.edu—educational; name.gov—government; ISPname.net—network provider (such as an ISP); name.ar—Argentina; name.au—Australia; and so on.DNS Domain Name System server. A server that translates text names into IP addresses. The server maintains a database of host alphanumeric names and their corresponding IP addresses.DSSS Direct sequence spread spectrum. A type of spread spectrum radio transmission that spreads its signal continuously over a wide frequency band.EEAP Extensible Authentication Protocol. An optional IEEE 802.1x security feature ideal for organizations with a large user base and access to an EAP-enabled Remote Authentication Dial-In User Service (RADIUS) server.Ethernet The most widely used wired local area network. Ethernet uses carrier sense multiple access (CSMA) to allow computers to share a network and operates at 10, 100, or 1000 Mb/s, depending on the physical layer used.Ffile server A repository for files so that a local area network can share files, mail, and programs.firmware Software that is programmed on a memory chip.Ggateway A device that connects two otherwise incompatible networks together.GHz Gigahertz. One billion cycles per second. A unit of measure for frequency.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-110.png)
![GlossaryGL-5Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01IIEEE Institute of Electrical and Electronic Engineers. A professional society serving electrical engineers through its publications, conferences, and standards development activities. The body responsible for the Ethernet 802.3 and wireless LAN 802.11 specifications.infrastructure The wired Ethernet network.IP address The Internet Protocol (IP) address of a station.IP subnet mask The number used to identify the IP subnetwork, indicating whether the IP address can be recognized on the LAN or if it must be reached through a gateway. This number is expressed in a form similar to an IP address; for example: 255.255.255.0.isotropic An antenna that radiates its signal in a spherical pattern.MMAC address Media Access Control address. A unique 48-bit number used in Ethernet data packets to identify an Ethernet device, such as an access point or your client adapter.MAP Mesh Access PointMBSSID Multiple basic SSID. Each multiple basic SSID is assigned a unique MAC address. You use multiple BSSIDs to assign a unique DTIM setting for each SSID and to broadcast SSIDs in beacons (one SSID per beacon). MIMO Multiple Input/Multiple Outputmodulation Any of several techniques for combining user information with a transmitter for a carrier signal.multipath The echoes created as a radio signal bounces off of physical objects.multicast packet A single data message (packet) sent to multiple addresses.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-111.png)
![GlossaryGL-6Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01Oomni-directional This typically refers to a primarily circular antenna radiation pattern. OFDM Orthogonal frequency division multiplex is a modulation technique used by IEEE 802.11a-compliant wireless LANs for transmission at 6, 9, 12, 18, 24, 36, 48, and 54 Mb/s.Ppacket A basic message unit for communication across a network. A packet usually includes routing information, data, and sometimes error detection information.QQPSKQuadruple phase shift keying is a modulation technique used by IEEE 802.11b-compliant wireless LANs for transmission at 2 Mb/s.Rrange A linear measure of the distance that a transmitter can send a signal.RAP Root Access Pointreceiver sensitivity A measurement of the weakest signal a receiver can receive and still correctly translate it into data.RF Radio frequency. A generic term for radio-based technology.roaming A feature of some access points that allows users to move through a facility while maintaining an unbroken connection to the LAN.RP-TNC A connector type unique to Cisco Aironet radios and antennas. Part 15.203 of the FCC rules covering spread spectrum devices limits the types of antennas that may be used with transmission equipment. In compliance with this rule, Cisco Aironet, like all other wireless LAN providers, equips its radios and antennas with a unique connector to prevent attachment of non-approved antennas to radios.S](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-112.png)
![GlossaryGL-7Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01spread spectrum A radio transmission technology that spreads the user information over a much wider bandwidth than otherwise required in order to gain benefits such as improved interference tolerance and unlicensed operation.SSID Service set identifier (also referred to as Radio Network Name). A unique identifier used to identify a radio network and which stations must use to be able to communicate with each other or to an access point. The SSID can be any alphanumeric entry up to a maximum of 32 characters.Ttransmit power The power level of radio transmission.UUNII Unlicensed National Information Infrastructure—regulations for UNII devices operating in the 5.15 to 5.35 GHz and 5.725 to 5.825 GHz frequency bands.UNII-1 Regulations for UNII devices operating in the 5.15 to 5.25 GHz frequency band.UNII-2 Regulations for UNII devices operating in the 5.25 to 5.35 GHz frequency band.UNII-3 Regulations for UNII devices operating in the 5.725 to 5.825 GHz frequency band.unicast packet A single data message (packet) sent to a specific IP address.UPoE Cisco Universal Power Over Ethernet (UPOE) extends IEEE PoE+ standard by doubling the power per port to 60W over a single standard Ethernet Cable. It allows the consolidation of 60 watts power on a single Ethernet (CAT5E or higher) cable, or in short 60W per access switch port.WWDS Wireless Domain Services. An access point providing WDS on your wireless LAN maintains a cache of credentials for CCKM-capable client devices on your wireless LAN. When a CCKM-capable client roams from one access point to another, the WDS access point forwards the client's credentials to the new access point with the multicast key. Only two packets pass between the client and the new access point, greatly shortening the reassociation time. WEP Wired Equivalent Privacy. An optional security mechanism defined within the 802.11 standard designed to make the link integrity of wireless devices equal to that of a cable.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-113.png)
![GlossaryGL-8Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation GuideOL-32138-01WLSE Wireless LAN Solutions Engine. The WLSE is a specialized appliance for managing Cisco Aironet wireless LAN infrastructures. It centrally identifies and configures access points in customer-defined groups and reports on throughput and client associations. WLSE's centralized management capabilities are further enhanced with an integrated template-based configuration tool for added configuration ease and improved productivity. WNM Wireless Network Manager. workstation A computing device with an installed client adapter.WPA Wi-Fi Protected Access is a standards-based, interoperable security enhancement that strongly increases the level of data protection and access control for existing and future wireless LAN systems. It is derived from and will be forward-compatible with the upcoming IEEE 802.11i standard. WPA leverages TKIP (Temporal Key Integrity Protocol) for data protection and 802.1X for authenticated key management.](https://usermanual.wiki/Cisco-Systems/102093P.Install-Guide-AIR-AP1570-Series/User-Guide-2497088-Page-114.png)