CipherLab 1260S Bluetooth Wireless Scanner User Manual Table of Contents

CipherLab Co., Ltd. Bluetooth Wireless Scanner Table of Contents

UserManual.wiki >

1260S User Manual >

Contents

1. users manual
2. barcode manual

barcode manual

Table of Contents Restore Default Settings .......................................................................................1 Exit Setup without Changes.................................................................................1 Set Connection.......................................................................................................1 RF Auto Shutdown Duration...............................................................................1 Memory Mode Parameters...................................................................................2 List Setting.............................................................................................................3 Buzzer Settings......................................................................................................3 Reading Redundancy Setting...............................................................................4 Scan Mode Setting.................................................................................................4 Auto-Sense Setting ................................................................................................4 Scanner Time-out Duration..................................................................................5 Negative Barcode Setting .....................................................................................5 Delay between Reread ..........................................................................................5 Keyboard Wedge Parameters..............................................................................6 Laptop Support .....................................................................................................8 RS-232 Parameters ...............................................................................................9 Bluetooth Serial Port Parameters......................................................................11 Prefix / Postfix Settings.......................................................................................12 Character Substitution .......................................................................................12 Code ID Selection................................................................................................12 Code ID Setting ...................................................................................................13 Length Code Setting (2 digits)............................................................................14 Select Readable Codes ........................................................................................17 Code39 Parameters.............................................................................................22 Italy Pharmacode Parameters............................................................................22 French Pharmacode Parameters .......................................................................23 Industrial 25 Parameters....................................................................................23 Interleave 25 Parameters....................................................................................24 Matrix 25 Parameters.........................................................................................26 Codabar Parameters...........................................................................................27 Plessey Parameters..............................................................................................28 Telepen Parameters ............................................................................................28 MSI Parameters..................................................................................................29 MSI Parameters..................................................................................................29 EAN128 Parameters ...........................................................................................30 EAN8 Parameters ...............................................................................................31 UPCA Parameters...............................................................................................31 UPCE Parameters...............................................................................................32 EAN13 Parameters .............................................................................................33 RSS Code ID Selection........................................................................................34 RSS14 Parameters...............................................................................................34 RSS Limited Parameters ....................................................................................35 RSS Limited Parameters....................................................................................35 Activate Editing Formats...................................................................................36 Editing Format Parameters ...............................................................................37 Decimal Digits .....................................................................................................49 Hexadecimal Digits .............................................................................................50 RS-232 Character Table.....................................................................................51

Restore Default Settings Memory Mode Parameters • Memory Mode Enable < Disable > Exit Setup without Changes • Clear Data Clear Confirm Set Connection * Programming Instructions : (1) Read the label. (2) Read the Serial Number barcode on the bottom of the desired 3660 Base Station within 5 seconds to complete this setting. • Send Data • Memory Data Delay RF Auto Shutdown Duration < 0 > 2 sec 250 ms 3 sec 500 ms 5 sec 1 sec 8 sec * Programming Instructions : (1) Read the label. (2) Program the desired auto shutdown duration (in minutes) by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. 2 Enter Setup 1 Update

List Setting Reading Redundancy Setting Page1 Page 6 Page 2 Page 7 Page 3 Page 8 Page 4 Page 9 Page 5 Page 10 < No Redundancy > 2 Times 3 Times 4 Times Scan Mode Setting Auto Off Mode < Continuous Mode > Auto Power Off Mode Alternate Mode Momentary Mode Repeat Mode Laser Mode Test Mode Buzzer Settings < Buzzer Enable> Buzzer Disable • Buzzer Frequency Auto-Sense Setting 8 kHz < 4 kHz > 2 kHz 1 kHz Enable < Disable > 4 Enter Setup 3 Update

Keyboard Wedge Parameters Scanner Time-out Duration • Activate and Select Keyboard Type * Programming Instructions : (1) Read the label. (2) Program the desired time-out duration by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. * Programming Instructions : (1) Read the label. (2) Program the desired keyboard number (shown in the following table) by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. Negative Barcode Setting • Keyboard Table Enable < Disable > No. Keyboard Type1 PCAT (US)2 PCAT (French)3 PCAT (German)4 PCAT (Italy) 5 PCAT (Swedish)6 PCAT (Norwegian)7 PCAT (UK) 8 PCAT (Belgium)9 PCAT (Spanish)10 PCAT (Portuguese)11 PS55 A01-1 12 PS55 A01-213 PS55 A01-314 PS55 001-115 PS55 001-8116 PS55 001-217 PS55 001-8218 PS55 001-319 PS55 001-8A20 PS55 002-1, 003-1 21 PS55 002-81, 003-81 22 PS55 002-2, 003-2 23 PS55 002-82, 003-82 24 PS55 002-3, 003-3 25 PS55 002-8A, 003-8A 26 IBM 3477 (Japanese) 27 PS2-30 28 IBM 34XX/319X, Memorex Telex 122 Keys Delay between Reread 100 ms 1 sec 200ms 2 sec < 400 ms > 3 sec 800 ms 5 sec 6 Enter Setup 5 Update

• Keyboard Alphabets Layout • Alphabet Transmission < Default Layout > AZERTY QWERTZ < Case Sensitive > Ignore Case • Digits Transmission < Alphanumeric Key > Numeric Key • Keyboard Digits Layout < Default Layout > Lower Row Upper Row • Alt Composing Yes < No > • Keyboard Capital Lock Type < Default > Shift Lock Capital Lock • Inter-Character Delay * Programming Instructions : (1) Read the label. (2) Program the desired inter-character delay by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. • Capital Lock Setting Capital Lock ON < Capital Lock OFF > Auto Detection Laptop Support < Disable> Enable 8 Enter Setup 7 Update

RS-232 Parameters • Flow Control < None > Scanner Ready Data Ready INV. Data Ready • Activate RS232 Interface • Baud Rate 115200 38400 19200 < 9600 > 4800 2400 1200 300 • Inter-Character Delay * Programming Instructions : (1) Read the label. (2) Program the desired inter-character delay by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. • Parity Even Odd < No Parity > • Data Bit < 8 > 7 10 Enter Setup 9 Update

Bluetooth Serial Port Parameters Prefix / Postfix Settings Prefix Code * Postfix Code * • Activate BlueTooth Serial Port Interface • Device Name Broadcasting Character Substitution < Yes > No Set 1 * Set 2 * Set 3 * • Authentication Yes < No > Programming Instructions : (1) Read the label. (2) Program the desired character string by reading Hexadecimal Digits on page 50. One character consists of 2 hexadecimal digits. (3) Read the “Validate” label (also on page 50) to complete this setting. • PIN Code Code ID Selection * • Clear All Code ID Settings Programming Instructions : (1) Read the label. (2) Program the desired character string by reading Hexadecimal Digits on page 50. One character consists of 2 hexadecimal digits. (3) Read the “Validate” label (also on page 50) to complete this setting. (4) Max 6 characters for this PIN Code setting. • Select Code ID Set Set 1 Set 2 Set 3 Set 4 Set 5 12 Enter Setup 11 Update

Code ID Setting Length Code Setting (2 digits) Code 39 * Italy Pharmacode * French Pharmacode * Industrial 25 * Interleave 25 * Matrix 25 * Codabar * UPCA * UPCE * EAN8 * EAN13 * Code 93 * Code 128 * MSI * Plessey * Telepen * • Code 39 Length Code Enable < Disable > • Italy Pharmacode Length Code Enable < Disable > • French Pharmacode Length Code Enable < Disable > • Industrial 25 Length Code Enable < Disable > • Interleave 25 Length Code Enable < Disable > Programming Instructions : (1) Read the label. (2) Program the desired character string by reading Hexadecimal Digits on page 50. One character consists of 2 hexadecimal digits. (3) Read the “Validate” label (also on page 50) to complete this setting. 14 Enter Setup 13 Update

• Matrix 25 Length Code • Code 93 Length Code Enable < Disable > Enable < Disable > • Code 128 Length Code • Codabar Length Code Enable < Disable > Enable < Disable > • EAN128/RSS Length Code • UPCA Length Code Enable < Disable > Enable < Disable > • MSI Length Code • UPCE Length Code Enable < Disable > Enable < Disable > • Plessey Length Code • EAN8 Length Code Enable < Disable > Enable < Disable > • Telepen Length Code • EAN13 Length Code Enable < Disable > Enable < Disable > 16 Enter Setup 15 Update

Select Readable Codes • Matrix 25 Enable < Disable > • Code 39 < Enable > Disable • Codabar < Enable > Disable • Italy Pharmacode Enable < Disable > • Code 93 < Enable > Disable • French Pharmacode Enable < Disable > • Code 128 < Enable > Disable • Industrial 25 < Enable > Disable • EAN128 Enable < Disable > • Interleave 25 < Enable > Disable • MSI Enable < Disable > 18 Enter Setup 17 Update

• Plessey • UPCE Enable < Disable > < Enable No Addon > Disable No Addon Enable Addon2 < Disable Addon2 > Enable Addon5 < Disable Addon5 > • Telepen Enable < Disable > • UPCA < Enable No Addon > Disable No Addon Enable Addon2 < Disable Addon2 > Enable Addon5 < Disable Addon5 > • EAN8 < Enable No Addon > Disable No Addon Enable Addon2 < Disable Addon2 > Enable Addon5 < Disable Addon5 > 20 Enter Setup 19 Update

Code39 Parameters • EAN13 • Standard / Full ASCII Code39 < Enable No Addon > Disable No Addon Enable Addon2 < Disable Addon2 > Enable Addon5 < Disable Addon5 > < Standard > Full ASCII • Start / Stop Transmission Enable < Disable > RSS14 • Checksum Verification Enable < Disable > Enable < Disable > • RSS Limited Enable < Disable > • Checksum Transmission < Enable > Disable • RSS Expanded Enable < Disable > Italy Pharmacode Parameters • Checksum Transmission < Enable > Disable> 22 Enter Setup 21 Update

French Pharmacode Parameters • Max / Min Code Length Qualification • Checksum Transmission Select Max / Min Length Qualification < Enable > Disable Max Length * Min Length * Industrial 25 Parameters • Fixed Code Length Qualification • Start / Stop Selection Select Fixed Length Qualification < Industrial 25 > Interleave 25 Matrix 25 Fixed Length 1 * Fixed Length 2 * Programming Instructions : (1) Read the label. (2) Program the desired length by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. • Checksum Verification Enable < Disable > Interleave 25 Parameters • Start / Stop Selection • Checksum Transmission Industrial 25 < Interleave 25 > Matrix 25 < Enable > Disable 24 Enter Setup 23 Update

• Checksum Verification • Fixed Code Length Qualification Enable < Disable > Select Fixed Length Qualification Fixed Length 1 * Fixed Length 2 * • Checksum Transmission < Enable > Disable Programming Instructions : (1) Read the label. (2) Program the desired length by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. • Max / Min Code Length Qualification Matrix 25 Parameters Select Max / Min Length Qualification • Start / Stop Selection Industrial 25 Interleave 25 < Matrix 25 > Max Length * Min Length * Programming Instructions : (1) Read the label. (2) Program the desired length by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. • Checksum Verification Enable < Disable > • Checksum Transmission < Enable > Disable 26 Enter Setup 25 Update

• Max / Min Code Length Qualification • Start / Stop Selection < abcd / abcd > abcd / tn*e ABCD / ABCD ABCD / TN*E Select Max / Min Length Qualification Max Length * Min Length * • Fixed Code Length Qualification Plessey Parameters Select Fixed Length Qualification • Convert to UK Plessey Fixed Length 1 * Fixed Length 2 * Enable < Disable > • Checksum Transmission Programming Instructions : (1) Read the label. (2) Program the desired length by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. < Enable > Disable Codabar Parameters Telepen Parameters • CLSI Conversion Enable < Disable > • Telepen Output < AIM Telepen > Original Telepen • Start / Stop Transmission Enable < Disable > 28 Enter Setup 27 Update

MSI Parameters • Fixed Code Length Qualification • Checksum Verification Select Fixed Length Qualification < Single Modulo 10 > Double Modulo 10 Modulo 11 & 10 Fixed Length 1 * Fixed Length 2 * Programming Instructions : (1) Read the label. (2) Program the desired length by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. • Checksum Transmission < Last digit not Transmitted > Transmitted Last 2 Digits not Transmitted EAN128 Parameters • Code ID Transmission Enable < Disable > • Max / Min Code Length Qualification Select Max / Min Length Qualification • Field Separator Max Length * Min Length * * Programming Instructions : (1) Read the label. (2) Program the desired character string by reading Hexadecimal Digits on page 50. One character consists of 2 hexadecimal digits. (3) Read the “Validate” label (also on page 50) to complete this setting. Programming Instructions : (1) Read the label. (2) Program the desired length by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. 30 Enter Setup 29 Update

EAN8 Parameters UPCE Parameters • Convert to EAN13 • System Number Selection Enable < Disable > System Number 0 and 1 < System Number 0 only > • Checksum Transmission • Convert to UPCA < Enable > Disable Enable < Disable > • System Number Transmission UPCA Parameters Enable < Disable > • Convert to EAN13 < Enable > Disable • Checksum Transmission < Enable > Disable • System Number Transmission < Enable > Disable • Checksum Transmission < Enable > Disable 32 Enter Setup 31 Update

EAN13 Parameters RSS Code ID Selection • ISBN Conversion ]C1 < ]e0 > Enable < Disable > RSS14 Parameters • ISSN Conversion • Code ID Transmission Enable < Disable > < Enable > Disable • Checksum Transmission • Application ID Transmission < Enable > Disable < Enable > Disable • Checksum Transmission < Enable > Disable 34 Enter Setup 33 Update

RSS Limited Parameters Activate Editing Formats • Code ID Transmission • Format 1 < Enable > Disable Enable < Disable > • Application ID Transmission • Format 2 < Enable > Disable Enable < Disable > • Checksum Transmission • Format 3 < Enable > Disable Enable < Disable > • Exclusive Data Editing RSS Limited Parameters Yes < No > • Code ID Transmission < Enable > Disable • Apply Editing Format to Telepen < Yes > No 36 Enter Setup 35 Update

Editing Format Parameters • Applicable Data Length Maximum Length * Minimum Length * • Format Selection Format 1 Format 2 Format 3 Programming Instructions : (1) Read the label. (2) Program the desired length by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. • Matching String of Applicable Data • Restore Default Format * Programming Instructions : (1) Read the label. (2) Program the desired character string by reading Hexadecimal Digits on page 50. One character consists of 2 hexadecimal digits. (3) Read the “Validate” label (also on page 50) to complete this setting. • Location of Matching String * Programming Instructions : (1) Read the label. (2) Program the desired location by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. 38 End of Format Programming 37 Update

• Total Number of Fields • Applicable Code Type 1 4 2 5 3 6 All Clear Code 39 Italy Pharmacode French Pharmacode Industrial 25 Interleave 25 Matrix 25 Codebar Code 93 Code 128 EAN128 / RSS UPCE No Addon UPCE Addon2 UPCE Addon5 EAN8 No Addon EAN8 Addon2 EAN8 Addon5 40 End of Format Programming 39 Update

• Field1 Setting EAN13 No Addon EAN13 Addon2 EAN13 Addon5 UPCA No Addon UPCA Addon2 UPCA Addon5 MSI Plessey Divide Field by Field Terminating String Field Terminating String * Programming Instructions : (1) Read the label. (2) Program the desired character string by reading Hexadecimal Digits on page 50. One character consists of 2 hexadecimal digits. (3) Read the “Validate” label (also on page 50) to complete this setting. Include Terminating String Discard Terminating String Divide Field by Field Length Field Length * Programming Instructions : (1) Read the label. (2) Program the desired length by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. 42 End of Format Programming 41 Update

• Field2 Setting • Field3 Setting Divide Field by Field Terminating String Divide Field by Field Terminating String Field Terminating String * Field Terminating String * Programming Instructions : (1) Read the label. (2) Program the desired character string by reading Hexadecimal Digits on page 50. One character consists of 2 hexadecimal digits. (3) Read the “Validate” label (also on page 50) to complete this setting. Programming Instructions : (1) Read the label. (2) Program the desired character string by reading Hexadecimal Digits on page 50. One character consists of 2 hexadecimal digits. (3) Read the “Validate” label (also on page 50) to complete this setting. Include Terminating String Discard Terminating String Include Terminating String Discard Terminating String Divide Field by Field Length Divide Field by Field Length Field Length * Field Length * Programming Instructions : (1) Read the label. (2) Program the desired length by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. Programming Instructions : (1) Read the label. (2) Program the desired length by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. 44 End of Format Programming 43 Update

• Field4 Setting • Field5 Setting Divide Field by Field Terminating String Divide Field by Field Terminating String Field Terminating String * Field Terminating String * Programming Instructions : (1) Read the label. (2) Program the desired character string by reading Hexadecimal Digits on page 50. One character consists of 2 hexadecimal digits. (3) Read the “Validate” label (also on page 50) to complete this setting. Programming Instructions : (1) Read the label. (2) Program the desired character string by reading Hexadecimal Digits on page 50. One character consists of 2 hexadecimal digits. (3) Read the “Validate” label (also on page 50) to complete this setting. Include Terminating String Discard Terminating String Include Terminating String Discard Terminating String Divide Field by Field Length Divide Field by Field Length Field Length * Field Length * Programming Instructions : (1) Read the label. (2) Program the desired length by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. Programming Instructions : (1) Read the label. (2) Program the desired length by reading Decimal Digits on page 49. (3) Read the “Validate” label (also on page 49) to complete this setting. 46 End of Format Programming 45 Update

• Additional Fields Setting • Field Transmission Sequence Additional Field 1 * Additional Field 4 * Additional Field 2 * Additional Field 5 * Additional Field 3 * Start Field 1 Additional Field 1 Field 2 Additional Field 2 Field 3 Additional Field 3 Field 4 Additional Field 4 Field 5 Additional Field 5 Field 6 Programming Instructions : (1) Read the label. (2) Program the desired character string by reading Hexadecimal Digits on page 50. One character consists of 2 hexadecimal digits. (3) Read the “Validate” label (also on page 50) to complete this setting. End Programming Instructions : (1) Read the “Start” label. (2) Program the desired transmission sequence by reading the Field / Additional Field labels. (3) Read the “End” label to complete this setting. 48 End of Format Programming 47 Update

Decimal Digits Hexadecimal Digits 0 5 1 6 2 7 3 8 4 9 0 8 1 9 2 A 3 B 4 C 5 D 6 E 7 F • Validate • Validate 49 Update 50 Enter Setup

$RS-232 Character Table 3450 1 2 6 7 0 DLE SP 0 @ P ` p1 SOH DC1 ! 1 A Q a q2 STX DC2 " 2 B R b r3 ETX DC3 # 3 C S c s4 EOT DC4 $ 4 D T d t5 ENQ NAK % 5 E U e u6 ACK SYN & 6 F V f v7 BEL ETB ' 7 G W g w8 BS CAN ( 8 H X h x9 HT EM ) 9 I Y i yA LF SUB * : J Z j zB VT ESC + ; K [ k {C FF FS , < L \ l |D CR GS - = M ] m }E SO RS . > N ^ n ~F SI US / ? O _ o DEL 51 Update$

Navigation menu