Chungear Co CE10612 Ceiling Fan Remote Controller (Transmitter) User Manual

Chungear Industrial Co Ltd Ceiling Fan Remote Controller (Transmitter)

User Manual

DC POWER CEILING FAN REMOTE CONTROL MANUALLEARNING PROCESSNOTE：The Hand Held Remote Control System is equipped with a learning frequency functionwhich has code combinations to prevent potential interference from other remote unitsStep: 1 Open the remote battery cover and install DC3V,CR2032 2pcs batteriesStep: 2 Within 30 seconds of turning the Receivers AC power ON.Step: 3 Press and hold remote “LEARN” key for over 5 seconds, once the receiver hasdetected the frequency, the receiver will make sound, Bi Bi, twice. This willindicate the receiver has learned the frequency that was previously selected onthe transmitter.NOTE: After the AC power is on, do not press any other button on thetransmitterbefore setting learning. Doing so will cause the procedure to fail. After completingthesteps above, you should be able to operate the ceiling fan and light. If the fan isnotresponding to the transmitter, please turn the power off to the receiver. And repeatstep1 and 2.NOTE: Remove the battery if not used for long periods of time to prevent damage to the hand held remote.FUNCTIONS OF TRANSMITTER1. ：To turn the fan on or off.2. +: Press this button to increasing fan speed and LED indicator would be on thepositionof fan speed. (1~6 speed)3.-:Press this button to decreasing fan speed and LED indicator would be ontheposition of fan speed.(1~6 speed)4. FAN TIMER:2hr：Setting up that the ceiling fan will turn off after 2 hours automatically.4hr：Setting up that the ceiling fan will turn off after 4 hours automatically.8hr：Setting up that the ceiling fan will turn off after 8 hours automatically.Press fan speed button to deactivate5. : To set fan wind direction up or down.6. : Tap once to activate. Light on ceiling fan blinks once to confirmWalkAway Delay is active. The light turns off after 1 minute. Press any key to cancel function.7. : Home Shield--Press and hold button to activate. Light on ceiling fan blinks two times to confirmHome Shield is active. Fan remains off and the light randomly turns on for a minimum of 5 minutes and amaximum of 20 minutes. The light remains off for 60 minutes between events. To deactivate press anybutton once8. : “NATURAL FLOW”, press the button for set fan speed change automatically. If fan speed is on 1st, 2nd,or 3rd, press this button for low fan speed changing automatically. If fan speed is on 4th, 5th, or 6th, pressthis button for high fan speed changing automatically. Press Fan Speed to deactivate.9. ：To turn on and turn off the light.10.When pressing remote button, the LED indicator on position 1 would be on. If you press remote button andLED indicator would not be on, you should change new DC3V,CR2032 2pcs batteries.LED indicator speed positionTR292A
To assure continued FCC compliance:FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consultthe dealer or an experienced radio/TV technician for help.CAUTION:To assure continued FCC compliance:Any changes or modifications not expressly approved by the grantee of this device could void the user's authority tooperate the equipment.FCC ID：KUJCE10612This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.

Navigation menu