Chungear Co CE10609 Ceiling Fan Remote Controller (Transmitter) User Manual

Chungear Industrial Co Ltd Ceiling Fan Remote Controller (Transmitter)

User Manual

WALL TRANSMITTEROPERATION AND INSTALLATION INSTRUCTIONS(Please keep this instruction pamphlet.)IMPORTANT POINTS TO REMEMBER:1. Read and save these instructions.2. Please note that all fixed wiring appliances should be installed by a qualified electrician.3. The supply to the remote control receiver should be connected through a mains switch, i.e. existing wallswitch.4. Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection.6. This unit is to be used for the control of ceiling fan and in an AC110/120V 60Hz power supply only.7. The receiver is acceptable for installation in damp and wet rated fans, but cannot be submerged in water. Thewall transmitter is only to be installed indoors.8. Do not pull on or cut leads shorter.9. Do not drop or bump the unit.10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place as thiswill damage the transmitter. Dispose of used battery properly, keep the battery out of reach of children.11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable(rheostat) wall control.INSTALLATION INSTRUCTIONS1. Ceiling fan must be set at HIGH speed before installation.2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopycomes up to cover the receiver and bracket. (FIG 1and 2)IMPORTANTYOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND THE LIGHT KITTO THE ON POSITION BEFORE INSTALLING THE REMOTE CONTROL.CAUTION: INCORRECT WIRE CONNECTION WILL DAMAGE THIS RECEIVER.
Installing Wall Bracket ( HANDSET TRANSMITTER):The wall control can be used together with handset control,You could install the bracket as the FIG.6 shows.FIG. 6 FIG. 7HANDSET TRANSMITTER OPERATION (FIG. 7)Activating the Learning process: Turn on the receiver power, press and hold the LEARN key (on the back of thetransmitter) for 1~3S. Refer to FIG. 7Fan will turn on at medium speed and light (if installed) will turn on. This confirms that the SMART SYNC setting isactive and ok.Transmitter use 2 pcs CR2032 3V batteries.LIGHT FUNCTION SELECT SWITCHIf the ceiling fan has fluorescent lighting, please slide the “light function select switch” to “O” position. If the ceilingfan has incandescent or halogen lighting, please slide the “light function select switch” to “D” position. (FIG. 7)Please note that the setting on wall transmitter and handset transmitter must the same.:Turn off the ceiling fan.：Press this button for forward/reverse airflow of ceiling fan.: Turn on the fan at high speed.: Turn on the fan at medium speed.: Turn on the fan at low speed.: Turn the light off.:Turn the light on.DIMMER-Press and hold to dim or brighten light to the desired level and release. (Incandescent or halogen onlyand light function select switch on “D” position.)To assure continued FCC compliance:FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inTR250B
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect theequipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or anexperienced radio/TV technician for help.CAUTION:To assure continued FCC compliance:Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operatethe equipment.FCC ID：KUJCE10609This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device maynot cause harmful interference, and (2) this device must accept any interference received, including interference that maycause undesired operation.

Navigation menu