Chungear Co CE10510 CEILING FAN REMOTE CONTROLLER (TRANSMITTER) User Manual

Chungear Industrial Co Ltd CEILING FAN REMOTE CONTROLLER (TRANSMITTER)

User Manual

CEILING FAN REMOTE CONTROLLEROPERATION AND INSTALLATION INSTRUCTIONS(Please keep this instruction pamphlet.)IMPORTANT POINTS TO REMEMBER:1. Read and save these instructions.2. Please note that all fixed wiring appliances should be installed by a qualified electrician.3. The supply to the remote control receiver should be connected through a mains switch, i.e.existing wall switch.4. Disconnect from power supply at wall switch before working on remote control receiver or ceilingfan.5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection.6. This unit is to be used for the control of ceiling fan and in a AC120V 60Hz power supply only.7. Do not install in lamp locations or immerse in water. (For indoor use only.)8. Do not pull on or cut leads shorter.9. Do not drop or bump the unit.10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takesplace as this will damage the transmitter. Dispose of used battery properly, keep the battery out ofreach of children.INSTALLATION INSTRUCTIONS1. Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pulling the “PullSwitch” after installation.2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket. Thecanopy comes up to cover the receiver and bracket.IMPORTANTYOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEEDAND LIGHT KIT (IF ANY) TO ON POSITION BEFORE OPERATINGREMOTE CONTROL.CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
CODE SWITCH1. CODE SWITCH: Codes are set by pushing dip switches up or down. It is imperative that the codeused for both transmitter and receiver is exactly the same; otherwise remote controller will not work.Please note the code switch will enable you to operate a second remote controller independently.For example, if you have two ceiling fans with 2 remote control units, set 2 different codes for eachset of transmitter/receivers. This means you can operate each ceiling fan independently.2. Your remote control is ready for use after 9V battery installation.FUNCTIONS OF TRANSMITTEROFF : Turn off the ceiling fan.HI : Turn on the fan at high speedMED : Turn on the fan at medium speedLOW : Turn on the fan at low speedLIGHT : ON/OFF- Press and release immediately to turn on or off thelightDIMMER- Press and hold on to dimmer or brighten the light.(Tungsten only) Max. 300W.To assure continued FCC compliance:FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect theequipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or anexperienced radio/TV technician for help.CAUTION:To assure continued FCC compliance:Any changes or modifications not expressly approved by the grantee of this device could void the user's authority tooperate the equipment.FCC ID：KUJCE10510This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This devicemay not cause harmful interference, and (2) this device must accept any interference received, including interference thatmay cause undesired operation.TRANSMITTERInstallation of Transmitter Wall Mount Holder with two screws.TR69A

Navigation menu