Cheng Uei Precision Industry H3 Bluetooth Headset User Manual Part II

Cheng Uei Precision Industry Co., Ltd. Bluetooth Headset Part II

Contents

User Manual Part II

34DRAFTTURNING HEADSET ON/OFFMAKING CALLSTo turn your headset on, press and hold the Call button until the indicator light flashes. Then, release the button. To turn your headset off, press and hold the Call button until the indicator light flashes rapidly and then turns off.INDICATOR LIGHTS IMPORTANT: Be sure to first follow theQuick Start Guideon the reverse side of this guideto complete initial setup of your H3.WEARING THE HEADSETOpen the earhook.Loop the earhook over your ear. Press the headset to your ear.123AUDIO TONESThe audio tones provide information about your headset status.Audio Tone  Headset StatusSingle high tone when Volume at minimumpressing volume button or maximumFive rapid high tones Low batteryrepeated every 60 sec.No audio indications; Out of rangedeteriorating qualityRing tone  Incoming callSingle high tone  Pairing confirmationSingle low tone  Voice activationDual high/low tone Voice tag not   recognizedSingle high tone  End callLow to high tone  Phone network     not availableTwo ascending tones Mute enabledTwo descending tones Mute enabledCallButtonNote: Your H3 supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone's user's guide for more information.Function  ActionMake a voice dial call Tap the Call button   and speak the     name after the toneEnd a call  Tap the Call buttonReceive a call  Tap the Call buttonReject a call  Press and hold the    Call button until you   hear a beepRedial last call  Press and hold the   Call button until you   hear a beepAnswer a second Press and hold the incoming call  Call button (places   first call on hold)MAKING CALLS CONTINUEDFunction  ActionToggle between two Press and holdactive calls  the Call buttonJoin a 3-way call  Press and hold   both Volume buttonsPut an active call on Press and hold thehold or resume a call Call button until youon hold   hear a beepTransfer a call from the Tap the Call buttonphone to the headsetDisable or enable the Press and holdindicator light  both Volume   buttons for 3 to 4    secondsMute or unmute a call Tap both Volume    buttonsNote: Some features are phone/network dependent.The indicator light provides information about your headset status.With the Charger Plugged InHeadset Indicator Headset StatusOn (steady)  ChargingOff   Charging completeWith No Charger Plugged InHeadset Indicator Headset StatusOff   Power offOn (steady)  Pairing mode10 rapid flashes  Pairing successfulSlow pulse   Connected    (on a call)Quick flash  Standby   (not on call)Note: After 5 minutes of inactivity, the light stops flashing to conserve power, but the headset remains in standby mode.Features and Functions GuideH3Bluetooth®Handsfree HeadsetCHANGING FOR USEON OTHER EAROpen the earhook 90degrees from theheadset.Gently lift and pull thetop of the earhook upand off the upper hinge pin. Then, pull it away to remove it.Flip the headset over.Hook the bottom of the earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin.1234You can wear your H3 headset on your left or right ear. The headset comes ready for the right ear. To change the headset for the left ear:CHANGING VOLUME BUTTON ORIENTATIONIf you change your headset to wear on the other ear, you can also change the orientation of the volume buttons. Turn the headset power off.Press the Call button along with the Volume button you want to assign as "volume up" button until the indicator light flashes twice.The headset power turns on.122 Pull Earhook UpHinge Pin1 Open EarhookVolume ButtonsCall Button
FEDERAL COMMUNICATIONS COMMISSION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

Navigation menu