Chamberlain Group The 2392 Remote Control Transmitter User Manual 114A3485 3c

Chamberlain Group Inc, The Remote Control Transmitter 114A3485 3c

Exhibit D Users Manual per 2 1033 b3

CLICKERMODEL KLIK1UUniversal Garage Door Opener Remote Control To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and thereare no obstructions to door travel.• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.© 2007, Clicker Corporation114A3485 All Rights ReservedRead instructions thoroughly BEFORE beginning.Start with garage door closed. Identify garage door opener type - Smart/Learn button orDIP Switch. Smart/Learn button or DIP Switches are located on motor unit or externalreceiver. Refer to owner’s manual if necessary.Proceed with instructions according to your type of garage door opener.NOTE: Products other than Chamberlain:If programming fails reverse dip switches (OFF to ONand ON to OFF).Chamberlain products:For Chamberlain remotes DO NOT use the “0” position,use “+” or “-”. If you already have a 3-button remote, DIPswitch #1 must be set to “-” if the large button is to openthe door. It may be necessary to reprogram originalremote controls.21211109853 7641 2ClickerRemoteExistingRemote34Press program buttonuntil LED lights.5Match DIP switches. Turnextra switches OFF.ORDIP SWITCH  SMART/LEARN BUTTON231KG KG4Motor UnitSelect a button to program.Press button         timesensuring LED stops flashingafter each press. Codeis accepted whendoor activates.REMOTE CONTROL BATTERYNOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modificationsof this receiver and/or transmitter are prohibited, except for changing the code setting orreplacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject tothe following two conditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may causeundesired operation.Dispose of batteries properly.Replace battery with 3V2032coin cell battery only.To prevent possible SERIOUS INJURY or DEATH:• NEVER allow small children near batteries.• If battery is swallowed, immediately notify doctor.CHART A# of  Brand Description Frequencytimes to pressbutton11 Chamberlain 9 Position 390 MHz12 Chamberlain 9 Position Canada 315 MHz13 Genie 12 Position 390 MHz14 Linear Multicode 10 Position 300 MHz15 Chamberlain 8 Position 390 MHz16 Stanley/Multicode 10 Position 310 MHz17 Genie 9 Position 390 MHz18 LinearMoore-O-Matic 8 Position 310 MHz19 Chamberlain 7 Position 390 MHzCHART B# of  Brand Type/Color of  Frequencytimes to  Smart/Learnpressbutton 1 Linear Mega-Code 318 MHz2 Chamberlain Orange 390 MHz3 Chamberlain Purple 315 MHz4 Chamberlain Green 390 MHz5 GenieOverhead Door Intellicode 315 MHz6 GenieOverhead Door Intellicode 390 MHz7 Stanley Secure Code 310 MHz9Wayne Dalton Rolling Code 372.5 MHzwww.clickerproducts.com  •  1-800-442-1255Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genieis a Trademark of Overhead Door Corporation. Linear is a Trademark of LinearCorporation. Stanley is a Trademark of The Stanley Works.Button 1Button 2Press program button.67Programming complete.Press selected buttonto test.To reduce risk of fire, explosion or chemical burn:• Replace ONLY with 3V2032 coin batteries.• Do NOT recharge, disassemble, heat above 100°C (212°F) orincinerate.The lithium battery should produce power for up to 5 years.1211109853 7641 2Press and release thesmart/learn button.5Select a button to program.Press button         timesensuring LED stops flashingafter each press. Code is accepted when one of thefollowing occurs:Button 1Button 2OROR1See Chart A to determine # of times topress button and writein blank on step 5.DIP SWITCH SMART/LEARN BUTTONPress program button.67Programming complete.Press selected buttonto test.3Press program buttonuntil LED lights.21See Chart B to determine # of times topress button and writein blank on step 5.

Navigation menu