Cardo Systems ER12 Bluetooth headset User Manual QGQ2PRO NB 009 001 QG0179 indd

Cardo Systems, Inc. Bluetooth headset QGQ2PRO NB 009 001 QG0179 indd

user manual

Q2 pro™GebrauchsanleitungGuide d’UtilisationGuida di AvvioGuia de UsarioUser Guidecommunication in motion™™QGQ2PRO_ NB 009_001 - QG0179.indd 1 2/15/10 5:51 PM
© Cardo Systems, Inc.The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Cardo Systems, Inc. is under license. Other trademarks and trade names are those of their respective owners.2scala rider® Q2™ proQGQ2PRO_ NB 009_001 - QG0179.indd 2 2/15/10 5:51 PM
CONTENTS OF RETAIL BOX INTRODUCTIONCongratulations, and thank you for choosing the scala rider Q2 pro Bluetooth® Headset for bikers. This Manual will help you operate the headset, but you should rst familiarize yourself with the Bluetooth functionality of your cellular phone and/or GPS device before using the scala rider Q2 pro.The retail box of the scala rider Q2 pro contains one headset unit. When paired with another scala rider Q2 pro, the headsets can be used as an Intercom at a range of up to 1,640 ft (500m), subject to terrain and external conditions. The scala rider Q2 pro oers the following uses:1. Bluetooth headset for mobile phone communication, supporting headset* and Handsfree* proles (10m range) 2. Bike-to-Bike Intercom Communication with another Q2 pro unit (up to 1,640 ft. / 500 m range) in Full Duplex** mode [purchased separately]3. Turn-by-Turn GPS Navigation instructions and Streaming Audio from compatible Bluetooth devices4. FM Radio – built in FM radio receiver with six preset stations5. MP3 Connectivity – Listen to your cable connected MP3 player while riding6. Bluetooth stereo headset for wireless music streaming (supporting the Bluetooth A2DP and AVRCP proles, compatible with a variety of MP3 Players, adapters and other audio devices)The scala rider Q2 pro can establish an audio connection with one Bluetooth device at a time. Please read the section “Using the Headset” to see how you can switch the audio connection between the paired devices.____________________* Mobile phones that do not support the Bluetooth Handsfree profile may prevent you from using the Redial and Call Reject features** Full duplex calls allow you to speak and hear the other party speak simultaneouslyMC – Multi-Connection• Radio On/Off/change stations• Initiate/Terminate Buddy Intercom call with Primary or Secondary BuddyCTRL – Control Button • Power On, Power Off• Answer/End Call• A2DP functionsCharging JackVolume Down / RewindVolume Up / ForwardNOTE: The scala rider Q2 pro is also available in a cord-mounted micro-phone version to better t certain full-faced helmets with tight chin sections. Headset Helmet Clamp The scala pro is also available in a cord-mounted micro-phone version to better t certain full-faced Helmet ClampTabSliding PlateMicrophoneRight Speaker(long cord)Left Speaker(short cord)MP3 JackBack Platescala rider® Q2™ pro3EnglishQGQ2PRO_ NB 009_001 - QG0179.indd 3 2/15/10 5:51 PM
Wall ChargerAllen WrenchVelcro PadsMP3 CableMP3 Cable HolderGlue PlatePre-moistened ToweletteCarry-PouchMicrophone Sponges Flat sponge for full-face helmets and round sponge for other helmet typesUser Guide, including Warranty and Registration formIMPORTANT: The scala rider Q2 pro is a water-resistant device, designed for use under moderate rain or snow conditions. However, the headset is not waterproof and should not be used under severe weather conditions.The cover tongue protecting the Charging Jack should be kept tightly closed at all times to prevent moisture from entering the device.BEFORE USING (CHARGING THE HEADSET)Make sure that the headset is fully charged for at least ve hours before initial use.1. Connect the wall charger to the headset’s Charging Jack (located between the two Volume Buttons).2. While charging, the Red Light turns on (it may take up to 15 seconds until the Red Light turns on). When charging is complete, the Red Light will turn o.SET UP AND CONFIGURATIONSTEP 1 SET UP FOR BIKE-TO-BIKE INTERCOM: PAIRING The scala rider Q2 pro can be paired with up to two other headsets for Intercom communication, referred to in this guide as:Primary BuddyandSecondary BuddyPairing is a one time process. Once the headsets are paired during this Setup Procedure, they will remain paired and automatically recognize each other whenever they are within range. NOTE: The scala rider Q2 pro allows you to speak via Intercom to one Buddy headset at a time. scala rider Q2 pro or other scala riderheadset Bike-to-Bike Intercom up to 500 m / 540 yd(in open terrain)Mobile phone Driver-to-Passenger Full-duplex IntercomConnection Built-inFM radioGPS MP3player4scala rider® Q2 pro™QGQ2PRO_ NB 009_001 - QG0179.indd 4 2/15/10 5:52 PM
PRIMARY BUDDY PAIRING (requires two scala rider Q2 pro headsets)1. If either headset is turned OFF, turn it ON by pressing and holding the CTRL Button until the Blue Light ashes three times.2. Make sure that both headsets are now ashing slowly in Blue. 3. Pick up one headset and simultaneously press and hold the CTRL Button and MC Button for at least six seconds until the Red Light begins flashing rapidly, indicating it is in Intercom Pairing mode.4. Repeat Step 3 again for the second scala rider Q2 pro headset. Both headsets should now be ashing rapidly in Red.5. Within a few seconds, both headsets will show a solid Red light for two seconds, and then begin flashing slowly in Blue.NOTE: If the Pairing process is not completed within one minute the headset will return to Standby mode.SECONDARY BUDDY PAIRING (requires three scala rider Q2 pro headsets)Once you have paired the Main scala rider Q2 pro to the Primary Buddy headset, repeat the procedure above to pair the Main scala rider Q2 pro to the Secondary Buddy headset. NOTE: The Main scala rider Q2 pro is able to communicate with either the Primary Buddy or the Secondary Buddy. The Primary Buddy and Secondary Buddy are not able to communicate directly via Intercom.NOTE: If the Pairing process is not completed within one minute the headset will return to Standby mode. STEP 2 (Optional)SET UP FOR RIDER-TO-PASSENGER INTERCOM: PAIRING There are two ways that the scala rider Q2 pro can be used for Driver-to-Passenger communication.A. Both Rider and Passenger are using scala rider Q2 pro headsets.To Pair the two headsets, follow the Steps listed in the section above titled PRIMARY BUDDY PAIRING (2 bikers).B. The Rider is using a scala rider Q2 pro and the Passenger is using an earlier scala rider headset (i.e. a scala rider Solo™, a scala rider FM™ or a scala rider TeamSet™ Driver unit headset).To Pair the two headsets:1. Starting with the earlier scala rider headset turned OFF, press and hold the CTRL button until the Red/Blue lights begin rapidly alternating.2. Starting with the scala rider Q2 pro turned ON, simultaneously press and hold the CTRL Button and MC Button for six seconds until the Red light begins ashing rapidly, indicating it is in Intercom Pairing mode. 3. Within a few seconds, the scala rider Q2 pro will show a solid Red light for two seconds, and then begin ashing slowly in Blue.NOTE: If the Pairing process is not completed within one minute the headset will return to Standby mode.NOTE: When using an earlier scala rider headset as a Passenger headset, Voice Connect Intercom can be initiated only by the scala rider Q2 pro headset. Manual Connect Intercom can be initiated from either headset by pressing the MC button for scala rider Q2 pro and CTRL button for any earlier scala rider headset.RESET INTERCOM PAIRINGYou can delete all of the headset’s Intercom pairings at any time.scala rider® Q2™ pro5scala rider® Q2 pro™EnglishQGQ2PRO_ NB 009_001 - QG0179.indd 5 2/15/10 5:52 PM
1. Place the scala rider Q2 pro into Intercom Pairing mode following the instructions in the PRIMARY BUDDY PAIRING section above.2. Once the Red Light begins ashing rapidly, press and hold Volume up for three seconds.3. The Red and Blue Lights will ash ve times, conrming that the Reset Pairing was successful.STEP 3SET UP FOR MOBILE PHONE CALLS: PAIRING If you have a Bluetooth enabled mobile phone and would like to make and receive phone calls using the scala rider Q2 pro, you must rst pair your headset to the mobile phone.NOTE: If you have a compatible Bluetooth GPS device you wish to use with the scala rider Q2 pro, please skip this step, and continue ahead to STEP 4: SET UP FOR BLUETOOTH GPS DEVICE.Pairing is a one time process. Once the headset is paired to a specific mobile phone during this Setup Procedure, they will remain paired and automatically recognize each other whenever they are within range. If the connection between the phone and headset is lost, tap the CTRL button to reconnect the devices.To Pair the scala rider Q2 pro to a Bluetooth Mobile Phone1. Turn on your phone and make sure its Bluetooth function is activated.2. With the scala rider Q2 pro headset turned ON, press and hold the CTRL Button for at least six seconds until the Red and Blue Lights begin rapidly alternating.3. Search for Bluetooth devices on your phone by following the phone’s instructions. Please consult your phone’s User Manual for more information.4. After a few seconds the phone will list the scala-rider Q2 pro as a discovered device. Select it and follow your phone’s instructions to accept the pairing.5. When prompted enter 0000 (four zeros) as your PIN or passkey.6. Your phone will conrm that pairing has succeeded and the headset will begin ashing slowly in Blue.NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode.With some mobile phones, you may need to tap the CTRL button to connect the headset to the phone after pairing is complete. The scala rider Q2 pro headset will automatically connect to the last phone connected to the headset.STEP 4SET UP FOR BLUETOOTH GPS DEVICE: PAIRING If you have a Bluetooth enabled GPS device and would like to transmit navigation instructions and sounds from the GPS device through the headset’s speakers, you must rst pair your headset to the GPS device. NOTE: Not all Bluetooth enabled GPS devices allow connections to Bluetooth headsets like the scala rider Q2 pro. Please consult your GPS device’s User Manual for more information.To Pair the scala rider Q2 pro to a Bluetooth GPS Device:1. Turn on your GPS device.2. With the scala rider Q2 pro headset turned ON, press and hold the volume up Button for at least six seconds until the Red and Blue Lights begin ashing simultaneously.3. Search for Bluetooth headsets on your GPS device by following the device’s instructions. Please consult your GPS device’s User Manual for more information.6scala rider® Q2™ proQGQ2PRO_ NB 009_001 - QG0179.indd 6 2/15/10 5:52 PM
4. If your GPS device prompts for a PIN or Passkey enter 0000 (four zeros).5. Your GPS device will conrm that pairing has succeeded. The headset will begin ashing slowly in Blue. 6. If you wish to use a Bluetooth mobile phone to make and receive calls through the headset, you must now pair your mobile phone to your GPS device by following your GPS and/or mobile phone’s instructions.NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode. GETTING STARTEDATTACHING THE CLAMP ON THE HELMETThe Helmet Clamp must be attached to the left side of the helmet. Once attached, the headset unit can be mounted or released from the Helmet Clamp at any time. If you wish to connect your MP3 player to your headset, please refer rst to the assembly instructions listed in section: USING THE MP3 PLAYER WITH YOUR HEADSET. There are two methods that can be used in order to attach the Clamp onto the helmet:Standard Method: Recommended for most helmet types.Glue Plate Method: Recommended for helmets to which the standard method cannot be applied, using the Glue Plate included in the box. Standard Method1. Use the enclosed Allen Wrench to loosen the two screws on the Back Plate.2. Slide the Back Plate between the internal padding and the external shell of the helmet. 3. Adjust the clamp’s location so that the microphone is located opposite your mouth and then tighten the screws. You may need to reposition the Clamp repeatedly until you identify the best spot. The microphone must be positioned vertically and not horizontally. If you have purchased a helmet clamp version with the corded micro-phone, please refer to section ATTACHING THE CORDED MICROPHONE CLAMP ON A FULL-FACED HELMET.Glue Plate MethodYou have the option to glue the Helmet Clamp onto your helmet, when the above standard method cannot be used, or in case you prefer to secure the Helmet Clamp with adhesive glue. This option has been successfully used for a range of high end helmets.NOTE: While we have no reason to believe that the gluing option might negatively affect any helmet, Cardo does not assume any responsibility to that affect, irrespective of its nature and circumstances. The Glue Plate is offered as a free option that you may choose to use at your own risk and subject to renouncement of any future claims.Caution: This process can be done only once! 1. Use the enclosed Allen Wrench to remove both Allen screws and release the Helmet Clamp’s back plate.2. Determine the location on the helmet where the Hel-met Clamp must be attached.3. Adjust the Helmet Clamp’s location on the Helmet so that the microphone is located opposite your mouth. You may need to reposition the Clamp repeatedly until you identify the best spot. The microphone must be positioned vertically and not horizontally (Be sure to clean the selected area prior to the gluing process).scala rider® Q2™ pro7EnglishQGQ2PRO_ NB 009_001 - QG0179.indd 7 2/15/10 5:52 PM
4. Use the pre-moistened Towelette to clean the helmet area where you want to install the Glue Plate. Allow to dry thoroughly.5. Peel the foil cover from the Glue Plates’ adhesive pad.6. Place the Glue Plate into position according to #3. Press rmly 15 seconds on all 3 parts of the Glue Plate.7. The adhesive pad bonds to full strength over the next 24 hours. Therefore it is recommended to not use the headset during this 24 hour period.8. Fasten the Clamp to the Glue Plate using the Allen screws that were previously removed.If you have purchased a helmet clamp version with the corded microphone, please proceed as follows: ATTACHING THE CORDED MICROPHONE CLAMP ON A FULL-FACED HELMETIf you are using the corded microphone version, you must rst make sure your helmet clamp is attached to your helmet as described in previous section (ATTACHING THE CLAMP ON THE HELMET). Clean the exact spot on the internal padding of the helmet, opposite your mouth, where the microphone will be placed and proceed as follows.a. Peel the foil cover from the adhesive Velcro pad and place the Velcro pad on the chosen location opposite your mouth.b. Attach the microphone to the Velcro, as shown in photo.c. When done, tighten the screws of the clamp POSITIONING THE SPEAKERSSpeaker ASpeaker BAttach the speakers to the Velcro inside your helmet opposite your ears (short speaker cord for the left ear [A] and the long speaker cord [B] for the right ear). You may want to use the supplied Velcro pad.Using two speakers inside the helmet may be prohibited in certain jurisdic-tions. If this is the case, you should tuck away the long corded speaker underneath the helmet padding as follows: Speaker ASpeaker BSpeaker BCableLead the speaker cord [B] alongside the rim of the padding to the right side and then back to the left side, near speaker [A]. Then place the speaker [B] underneath the padding. ATTACHING AND REMOVING THE HEADSET FROM THE HELMET CLAMPATTACHING:Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place.8scala rider® Q2™ proQGQ2PRO_ NB 009_001 - QG0179.indd 8 2/15/10 5:52 PM
REMOVING: Press here to removeYour headset can be removed for charging and storage by pressing your nger gently against the tab and sliding the headset up with the other hand.We recommend that you remove the headset from the helmet when not in use.USING THE HEADSETGENERAL USAGEGENERAL FUNCTIONSDESIRED RESULT: REQUIRED ACTION:Turn on the headset Press the CTRL Button steadily for at least three secondsTurn o the headset Press the CTRL Button steadily for at least three secondsIncrease the volume Tap the Volume Up ButtonDecrease the volume Tap the Volume Down ButtonAGC (Automatic Gain Control): In addition to manual Volume Control, the scala rider Q2 pro will automatically increase and reduce its volume according to ambient noise and driving speed.AUDIO SOURCES AND PRIORITIESThe dierent Audio Sources that are connected to the scala rider Q2 pro are prioritized as follows:Highest 1. Mobile phone Audio / GPS device (Incoming/outgoing calls , GPS audio and navigation instructions) 2. Primary Buddy Audio and Secondary Buddy Audio 3. A2DP audio source 4. FM RadioLowest 5. MP3 Connectivity (corded connection)A high priority Audio Source will always interrupt any lower priority Audio Source. i.e. Mobile phone call interrupts Intercom call Intercom call interrupts FM RadioUSING THE INTERCOM Making Intercom callsTo start a Buddy Intercom call with the Primary Buddy while the headset is on Standby you can either:VOICE CONNECT: Start talking A Buddy Intercom call will be established and stay on until both sides are quiet for 30 seconds. MC BUTTON CONNECT: Single tap the MC Button A Buddy Intercom call will be established. To end the Buddy Intercom call, single tap the MC Button again.To start a Buddy Intercom call with the Secondary Buddy while the headset is on Standby:MC BUTTON CONNECT:Double tap the MC Button A Buddy Intercom call will be established. To end the Buddy Intercom call, double tap the MC Button again.NOTE: When using a scala rider Headset (not a Q2 pro version) as a Passenger headset, Voice Connect Intercom can be initiated only by the scala rider Q2 pro headset. Manual Connect Intercom can be initiated from either headset.Failed Connection: On the scala rider Q2 pro, if you attempt to start a Buddy Intercom call with a Buddy that is already on a Phone/GPS/Intercom call, you will hear a double beep indicating the Buddy is busy.orpro version) as a version) as a MC Buttonscala rider® Q2™ pro9EnglishQGQ2PRO_ NB 009_001 - QG0179.indd 9 2/15/10 5:52 PM
Reconnecting the Intercom: If the scala rider Q2 pro and its Intercom Buddy headset go out of range and disconnect from each other, the scala rider Q2 pro will automatically try to reconnect to its Intercom Buddy for ve minutes.You can manually reconnect at any time by pressing the MC Button (single tap for Primary Buddy and double tap for Secondary Buddy).Receiving Intercom callsIf you are not speaking with any one, once the other party tries to initiate a Buddy Intercom call, the call will begin immediately.TROUBLESHOOTING THE INTERCOM: First, make sure your microphone is located properly in front of the center of your mouth.The scala rider Q2 pro is designed for use in loud environments. Please make sure to test the Intercom functionality in a LOUD environment, such as next to an idling motorcycle.Please also verify that the headsets were paired together properly by following the instructions in the relevant Setup sections.Setting Voice Connect Intercom preference (Primary vs. Secondary Buddy)The headset’s Voice Connect feature allows you to start a Buddy Intercom call by simply speaking into the microphone. You can dene which of the two Buddy headsets you wish to connect to when using Voice Connect Intercom.NOTE: The Primary Buddy has priority by default. To toggle the Voice Connect Intercom between Primary and Secondary Buddy:Press and hold the Volume Up Button for three seconds and you will hear a beep:• One beep – Voice Connect set to Primary Buddy• Two beeps – Voice Connect set to Secondary BuddyEnable/Disable Voice Connect featurePress and hold the Volume Up and Down Buttons simultaneously until you hear a beep. The default status is Voice Connect enabled.NOTE: The Enable/Disable Voice Connect feature aects the Intercom functionality only. MAKING AND RECEIVING MOBILE PHONE CALLSPHONE FUNCTIONSAnswer a call Tap the CTRL Button or speak loudly any word of your choice during an incoming call.Reject a call Tap the MC Button or remain silent for 15 seconds during an incoming call.Terminate a call Tap the CTRL Button to end a call.Voice Dial During Standby, tap the CTRL Button and state the name of the person you wish to call. This feature is supported only by mobile phones that support the Voice Dial feature.Redial Press and hold the Volume Down Button for three seconds during Standby.NOTE: If your Bluetooth mobile phone is paired to a Bluetooth GPS device, not directly to the scala rider Q2 pro, some of the above Phone functions may not be compatible.When the headset is on an active phone call, any Buddy Intercom call request will be rejected automatically.10 scala rider® Q2™ proQGQ2PRO_ NB 009_001 - QG0179.indd 10 2/15/10 5:52 PM
Once the phone call audio link drops, you can initiate and accept Buddy Intercom calls.STATUS LIGHT STATESNone Headset is oAlternating Red/blue ashes Mobile phone/GPS Pairing modeRapid Red ashes Intercom Pairing mode1 blue ash every 3 seconds Standby – No call is in progress2 blue ashes every 3 seconds Call being initiated or in progress / FM Radio ON / MP3 player on1 red ash every 3 seconds Standby – Battery is low2 red ashes every 3 seconds Battery is low while call is in progress/ MP3 player is ON / FM Radio ONSolid red Headset is being chargedWORKING WITH THE FM RADIOYour headset is equipped with a high-quality FM Radio receiver and RDS (Radio Data System) technology, allowing you to choose how and when you listen to your favorite stations.The scala rider Q2 pro enables you to listen to FM Radio while you are not receiving audio from another audio source. While listening to the radio, you do not have to worry about missing any calls, as the headset automatically mutes the FM Radio and switches to Bluetooth headset operation when an incoming call is received, or when you decide to initiate a call. When the conversation is over, the headset automatically tunes back in to the FM Radio.The RDS FeatureThanks to the RDS feature, your headset will automatically select the strongest signal available for the FM station you wish to listen to, no matter where you are riding. This allows you to leave your hands on the handlebars at all times with no need to adjust the radio station frequency while you are in motion.To use the RDS feature while the Radio is on, press and hold the Volume Up and Volume Down Buttons simultaneously for 3 seconds. The RDS feature is set OFF by default. Turning the FM Radio OnWhile no call is on the headset (either mobile phone call or Intercom call), press and hold the MC Button on your headset for three seconds to turn on the radio. The radio tunes in to the last radio station you were listening to. With some phones you should wait a few seconds after ending a call before turning on the Radio.Turning the FM Radio OWhile the radio is turned on, press and hold the MC button for three seconds to turn the Radio o.Switching Preset FM Radio StationThere are six pre-set Radio stations available on your scala rider Q2 pro. While the Radio is on, tap the MC Button to cycle between saved stations.Searching for a New FM Radio StationWhile the Radio is on, press and hold the Volume Up or Volume Down Button for three seconds or until you hear the next station on your headset.Pressing Volume Up will search upwards (higher frequency). Pressing Volume Down will search downwards (lower frequency). Once a station is found, searching stops and you can hear the station.To save this station, refer to the following section.To continue searching, press the Volume Up or Volume Down Button again for three seconds.scala rider® Q2™ pro11English11EnglishQGQ2PRO_ NB 009_001 - QG0179.indd 11 2/15/10 5:52 PM
You may still continue to listen to the current unsaved station. Pressing the MC Button in this case will switch to the next saved station.Saving an FM Radio StationThe FM Radio is equipped with a memory capacity of six stations.• Select the station you wish to replace by tapping the MC button until you nd the station you want to replace.• Search for a new station as described above.• Tap the MC Button within 20 seconds of finding the station to save the current station.If you don't save the station, the Radio will exit search mode without saving the current station. You can still continue to listen to the current unsaved station. Tapping the MC Button in this case will move to the next saved station.MP3 AUDIOYour scala rider Q2 pro oers 2 dierent MP3 audio options:1. Wireless A2DP option2. Cable option.MP3 MUSIC – WIRELESS A2DP OPTIONYour headset is designed to receive wireless stereo music from A2DP sources and mobile phones that support the Bluetooth A2DP and AVRCP proles (mostly 3rd generation devices).Using a Bluetooth device that supports the AVRCP prole will allow you to operate all major A2DP source functions directly from your headset.While listening to music from an A2DP source, you will not miss any mobile or intercom calls, as the headset will automatically stop the music giving preference to the incoming call. However, after you ter-minate your call, some MP3 sources may not automatically continue but require manual re-activation. Setting Up Your MP3 Player for Bluetooth Stereo A2DP Transmission To use a Bluetooth Stereo (A2DP) enabled MP3 Player or Adapter to listen to stereo music, you must rst pair the device to your headset. Pairing the Headset to an MP3 Player or AdapterNOTE: If your A2DP source is integrated inside your Mobile Phone, then you should pair it with your headset as described earlier in step 31. Turn on your MP3 Player or Adapter, and make sure that its Bluetooth function is activated.2. With the scala rider Q2 pro headset turned ON, press and hold the Mobile Button for at least six seconds until the Red and Blue Lights begin alternating rapidly:3. Search for Bluetooth headsets on your MP3 Player by following the device’s instructions.NOTE: For use of a Bluetooth adapter, follow the device’s instructions.4. After a few seconds the MP3 Player will list “scala rider Q2 pro” as a discovered device. Select it and follow your MP3 Player’s instruc-tions to accept the pairing.5. If your MP3 player prompts for a PIN or Passkey enter 0000 (four zeros).6. Once pairing is complete, your MP3 Player or Adapter may conrm that pairing has succeeded, and the headset will begin ashing slowly in Blue. NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode.Operating Your A2DP Source from Your HeadsetPlay press and hold the CTRL Button for 3 secondsPause/Stop* press and hold the CTRL Button for 3 secondsForward press and hold the Volume Up Button for 3 secondsRewind press and hold the Volume Down Button for 3 seconds* Varies depending on your mobile phone model12 scala rider® Q2™ proQGQ2PRO_ NB 009_001 - QG0179.indd 12 2/15/10 5:52 PM
CABLE OPTION  USING THE MP3 PLAYER WITH YOUR HEADSETYour scala rider Q2 pro headset can be connected to an MP3 player device by plugging it to the Helmet Clamp’s jack with the MP3 cable.At your option, you may further secure the MP3 cable by using the MP3 cable holder. For this purpose please proceed as follows:MP3 cable holder hook1. Use the enclosed Allen Wrench to remove both Allen screws from Helmet clamp and release the clamp’s back plate. 2. Place the MP3 cable holder on the helmet clamp. Both pins on the MP3 cable holder should be xed into corresponding indentations on clamp. 3. Place the Back Plate on top of the MP3 cable holder and secure all parts together using the Allen screws that were previously removed, as shown in photo.4. Attach the clamp and headset onto your helmet as described previously in section “ATTACHING THE CLAMP ON THE HELMET”.5. Attach the speakers to your helmet as described in section ”POSITIONING THE SPEAKERS”.Insert cable in hook6. Connect the MP3 cable to your MP3 player device’s jack and the other side to the helmet Clamp’s jack, inserting the cable through the MP3 cable holder.Make sure that the cable plug clicks into place.7. Tuck the MP3 cable into the hook of the MP3 cable holder. 8. In order to use your MP3 player, power on the headset to have it on Standby mode, ashing slowly in Blue.NOTE: Operate the MP3 Player device by using its buttons (FF/REW/PLAY/PAUSE).Volume can only be adjusted through the MP3 Player. Any other audio connection will automatically mute the MP3 Player. The audio signal will return only when headset is once again in Standby mode.SUPPORTFor additional information please visit our website atwww.cardosystems.com FAQ: www.cardosystems.com/support/faqor contact us at:support@cardosystems.comPhone: USA and Canada – + 1-800-488-0363 International – +4989 450 36819NOTICESFederal Communications Commission (FCC) Statement15.21You are cautioned that changes or modications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.15.105(b)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:scala rider® Q2™ pro13EnglishQGQ2PRO_ NB 009_001 - QG0179.indd 13 2/15/10 5:52 PM
• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Operation is subject to the following two conditions:1) this device may not cause interference and2) this device must accept any interference, including interference that may cause undesired operation of the device.FCC RF Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specic operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Industry Canada (IC) Statement15.21You are cautioned that changes or modications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.15.105(b)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the IC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Operation is subject to the following two conditions:1) this device may not cause interference and2) this device must accept any interference, including interference that may cause undesired operation of the device.IC RF Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specic operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.European CE Notice The scala rider Q2™ pro headset (the “Product”) is in conformity with the following essential requirements of Council Directive 1999/5/EC (referred to as R&TTE Directive): Articles 3.1a, 3.1.b and 3.2. The Product is manufactured in accordance with Annex II of the above directive.Declaration of Conformity (DOC)The scala rider Q2™ pro headset is compliant with and adopts the Bluetooth® Specication 2.0 and has successfully passed all interoperability tests that are specied in the Bluetooth® specication. However, interoperability between the device and other Bluetooth®-enabled products is not guaranteed.WAIVER AND GENERAL RELEASEUsing a communication device while riding a motorcycle, scooter, moped, ATV, quad-bike or any other vehicle or equipment, whether on land, water or air (jointly referred to as “Vehicle”) requires your complete and undivided attention. Cardo Systems, Inc., including its Ocers, Directors, Aliates, Parent Company, Represen-tatives, Agents, Contractors, Sponsors, Employees, Suppliers and Resellers (jointly referred to as the “Company” or “Cardo”) strongly advises you to take all necessary precautions and remain alert to the trac, weather and road conditions if you choose to use the scala rider Q2 pro headset, including all derivative models ir-respective of its commercial name or branding (the “Device”), and stop your Vehicle on the roadside prior to initiating or receiving calls. Any publications, advertise-ments, announcements or similar notes that refer to using the Device while riding a Vehicle are solely intended to address its technical capabilities and should not be misconstrued as if encouraging users to operate the Device while actively involved in trac.By way of purchasing this Device and not returning it for a full refund (see below), you are irrevocably releasing, indemnifying from any liability, loss, claim and expense (including attorneys fees) and holding Cardo harmless for any bodily injuries, harm or death as well as losses or damages in goods, to any Vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdiction. Cardo will not be responsible for any physical damages, irrespective of reasons, condi-scala rider® Q2™ pro14 scala rider® Q2 pro™QGQ2PRO_ NB 009_001 - QG0179.indd 14 2/15/10 5:52 PM
tions or circumstances, including malfunctioning of the Device, and all risks associated with operating it rest solely and entirely with the user of this Device, irrespective of whether the Device is used by the original purchaser or any third party.Cardo hereby noties you that using this Device may also be in contravention to local, federal, state or national laws or regulations, and that any use of the Device is entirely at your sole risk and responsibility.1. You, your heirs, legal representatives, successors or assigns, hereby voluntarily and for-ever release, discharge, indemnify and hold harmless Cardo from any and all litigation, claims, debts, demands, actions and liability which may arise, directly or indirectly, from using the Device for any distress, pain, suering, discomfort, loss, injury, death, damages to or in respect to any person or property however caused, WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to you on some future date as a result of said use, to the fullest extent permitted by law.2. You fully understand and assume the risks in using the Device, including risk of negli-gent acts or omissions by others.3. You conrm that you are physically capable to use the Device and that you have no medical conditions or needs that may infringe upon your abilities to do so in a safe manner. You conrm that you are at least eighteen (18) years of age and that you have been advised of the risks associated with the use of the Device. You further conrm that you will not consume any alcohol that may aect your alertness or any mind-altering substance, and will not carry, use or consume these substances before or during the use of the Device.4. You fully acknowledge our warnings and understand that: (a) risks and dangers exist in using the Device while in trac, including but not limited to injury or illness, strains, fractures, partial and/or total paralysis, death or other ailments that could cause serious disability; (b) these risks and dangers may be caused by the negligence of the manufacturers or its agents or any third party involved in designing or manufacturing the Device; (c) these risks and dangers may arise from foreseeable or unforeseeable causes. You hereby assume all risks and dangers and all responsibility for any losses and/or damages, whether caused in whole or in part by the negligence or other conduct of others, including the Company.5. You conrm that you have read this release of liability and fully understand its terms and that you have given up substantial rights by not returning the Device for a full refund (see refund option below).Disclaimer of Warranty CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGE-MENT. THE DEVICE AND ITS ACCESSORIES ARE PROVIDED “AS IS” AND “AS AVAILABLE” WITHOUT WARRANTY OF ANY KIND BEYOND THOSE ASSUMED IN THE ENCLOSED MANUAL.Limitation of Liability IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THE DEVICE, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. YOU ACKNOWLEDGE AND AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE FUNDAMENTAL ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT BE PROVIDED TO YOU ABSENT SUCH LIMITATIONS. SOME STATE STATUTES MIGHT APPLY REGARDING LIMITATION OF LIABILITY.www.cardosystems.comscala rider® Q2™ pro15EnglishQGQ2PRO_ NB 009_001 - QG0179.indd 15 2/15/10 5:52 PM
16 scala rider® Q2™ proQGQ2PRO_ NB 009_001 - QG0179.indd 16 2/15/10 5:52 PM

Navigation menu