Cambium Networks XIAC3470 802.11abgn/ac module User Manual aos AppNotices

Xirrus, Inc. 802.11abgn/ac module aos AppNotices

Contents

Notices to User

Wireless Access Point559Appendix D: Notices (XR-1000 to XR-6000 Indoor Models)This appendix contains the following information: “Notices” on page 559“EU Directive 1999/5/EC Compliance Information” on page 564“Compliance Information (Non-EU)” on page 571“Safety Warnings” on page 573“Translated Safety Warnings” on page 574“Software License and Product Warranty Agreement” on page 576“Hardware Warranty Agreement” on page 576NoticesWi-Fi Alliance Certificationwww.wi-fi.orgFCC NoticeThis device complies with Part 15 of the FCC Rules, with operation subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unwanted operation.This Appendix contains Notices, Warnings, and Compliance information for these indoor model series: XR-1000, XR-2000, XR-4000, and XR-6000. This includes the models just listed whether or not they have been upgraded to have IEEE 802.11ac Wave2 wireless capability by replacing existing radios with XI-AC3470 modules.For the XR-500/600/XD Series, please see “Notices (XD and XR500/600 Series Only)” on page 541. For models including the letter H (such as the XR-520H and XH2-120), please see the Quick Installation Guide for that model.
Wireless Access Point560This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate RF energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following safety measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and the receiver.Consult the dealer or an experienced wireless technician for help.Use of a shielded twisted pair (STP) cable must be used for all Ethernet connections in order to comply with EMC requirements.High Power RadarsHigh power radars are allocated as primary users (meaning they have priority) in the 5250MHz to 5350MHz and 5650MHz to 5850MHz bands. These radars could cause interference and/or damage to LE-LAN devices.Non-Modification StatementUnauthorized changes or modifications to the device are not permitted. Use only the supplied internal antenna, or external antennas supplied by the manufacturer. Modifications to the device will void the warranty, void the user’s authority to operate the equipment, and may violate FCC regulations (Reference: FCC Part 15, section 15.21). Please see the Xirrus Web site for a list of all approved antennas.Cable Runs for Power over Gigabit Ethernet (PoGE)If using PoGE, the Array must be connected to PoGE networks without routing cabling to the outside plant — this ensures that cabling is not exposed to lightning strikes or possible cross over from high voltage.
Wireless Access Point561UL StatementUse only with listed ITE product.Battery Warning RF Radiation Hazard Warning (FCC and Industry Canada)For APs with IEEE 802.11ac Wave2 radios, install the unit being careful to keep the separation distances indicated in the table below between radiating elements of access point and users. This is consistent with the security warning exposure limits specified by the RSS-102 to relative radio frequencies.Pour les appareils IEEE 802.11ac Wave2, installez l'appareil en veillant à conserver les distances de séparation indiquées dans la table ci-dessus entre les éléments rayonnants et les personnes. Cet avertissement de sécurité est conforme aux limites d'exposition définies par la norme CNR-102 relative aux fréquences radio. For other APs, to ensure compliance with FCC and Industry Canada (IC) RF exposure requirements, this device must be installed in a location where the antennas of the device will have a minimum distance of at least 30 cm (12 inches) from all persons. !Caution! The AP contains a battery which is not to be replaced by the customer. Danger of Explosion exists if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.802.11ac Wave2 Modules (Radios) in APFCC Separation Distance (cm)IC Separation Distance (cm)1 module 20.0 21.2XR6000 - 12 modules 51.3 51.6XR4000 - 8 modules 44.0 50.8XR2000 - 4 modules 31.1 39.9
Wireless Access Point562Pour les autres appareils, installez l'appareil en veillant à conserver une distance d'au moins 30 cm entre les éléments rayonnants et les personnes. Cet avertissement de sécurité est conforme aux limites d'exposition définies par la norme CNR-102 at relative aux fréquences radio.Industry Canada Notice and MarkingThis Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Wireless Access Point563This equipment should be installed and operated with a minimum distance of 30cm between the radiator and your body. Cet équipement doit être installé et utilisé à une distance minimale de 30cm entre le radiateur et votre corps.High Power RadarsHigh power radars are allocated as primary users (meaning they have priority) in the 5250MHz to 5350MHz and 5650MHz to 5850MHz bands. These radars could cause interference and/or damage to LELAN devices used in Canada.Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250 - 5 350 MHz et 5 650 - 5 850 MHz. Ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Wireless Access Point564EU Directive 1999/5/EC Compliance InformationThis section contains compliance information for the Xirrus Wireless Array family of products. The compliance information contained in this section is relevant to the European Union and other countries that have implemented the EU Directive 1999/5/EC.Declaration of ConformityThis Appendix contains Notices, Warnings, and Compliance information for these indoor model series: XR-1000, XR-2000, XR-4000, and XR-6000. This includes the models just listed whether or not they have been upgraded to have IEEE 802.11ac Wave2 wireless capability by replacing existing radios with XI-AC3470 modules.For Notices, Warnings, and Compliance information for other models, see the notes at the beginning of this chapter. Cesky [Czech] Toto zahzeni je v souladu se základnimi požadavky a ostatnimi odpovidajcimi ustano veni mi Směrnice 1999/5/EC.Dansk [Danish] Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF.Deutsch [German] Dieses Gerat entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtinie 1999/5/EU.Eesti [Estonian] See seande vastab direktiivi 1999/5/EU olulistele nöuetele ja teistele as jakohastele sätetele.English This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Español [Spain] Este equipo cump le con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE.
Wireless Access Point565Ελληνυκη [Greek] Αυτόζ ο εξοπλτσμόζ είναι σε συμμόρφωση με τιζ ουσιώδειζ απαιτήσειζ και ύλλεζ σχετικέζ διατάξειζ τηζ Οδηγιαζ 1999/5/EC.Français [French] Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC.ĺslenska [Icelandic] Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.Italiano [Italian] Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE.Latviski [Latvian] Šī iekārta atbilst Direktīvas 1999/5/EK būtiskajāprasībām un citiem ar to saistītajiem noteikumiem.Lietuvių [Lithuanian] Šis įrenginys tenkina 1995/5/EB Direktyvos esminius reikalavimus ir kitas šios direktyvos nuostatas.Nederlands [Dutch] Dit apparant voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1995/5/EC.Malti [Maltese] Dan l-apparant huwa konformi mal-htigiet essenzjali u l-provedimenti l-ohra rilevanti tad-Direttiva 1999/5/EC.Margyar [Hungarian] Ez a készülék teljesiti az alapvetö követelményeket és más 1999/5/EK irányelvben meghatározott vonatkozó rendelkezéseket.Norsk [Norwegian] Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.Polski [Polish] Urządzenie jest zgodne z ogólnymi wymaganiami oraz sczególnymi mi warunkami określony mi Dyrektywą. UE:1999/5/EC.
Wireless Access Point566Assessment CriteriaThe following standards were applied during the assessment of the product against the requirements of the Directive 1999/5/EC:Radio: EN 301 893 and EN 300 328 (if applicable)EMC: EN 301 489-1 and EN 301 489-17Safety: EN 50371 to EN 50385, EN 60601, and EN60950CE MarkingFor the Xirrus Wireless Array, the CE mark and Class-2 identifier opposite are affixed to the equipment and its packaging: Portuguès [Portuguese] Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.Slovensko [Slovenian] Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi popoji Direktive 1999/5/EC.Slovensky [Slovak] Toto zariadenie je v zhode so základnými požadavkami a inými prislušnými nariadeniami direktiv: 1999/5/EC.Suomi [Finnish] Tämä laite täyttää direktiivin 1999/5//EY olennaiset vaatimukset ja on siinä asetettujen muiden laitetta koskevien määräysten mukainen.Svenska [Swedish] Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC.
Wireless Access Point567WEEE ComplianceNatural resources were used in the production of this equipment.This equipment may contain hazardous substances that could impact the health of the environment.In order to avoid harm to the environment and consumption of natural resources, we encourage you to use appropriate take-back systems when disposing of this equipment.The appropriate take-back systems will reuse or recycle most of the materials of this equipment in a way that will not harm the environment.The crossed-out wheeled bin symbol (in accordance with European Standard EN 50419) invites you to use those take-back systems and advises you not to combine the material with refuse destined for a land fill.If you need more information on collection, re-use and recycling systems, please contact your local or regional waste administration.Please contact Xirrus for specific information on the environmental performance of our products.
Wireless Access Point568National RestrictionsIn the majority of the EU and other European countries, the 2.4 GHz and 5 GHz bands have been made available for the use of Wireless LANs. The following table provides an overview of the regulatory requirements in general that are applicable for the 2.4 GHz and 5 GHz bands.*Dynamic frequency selection and Transmit Power Control is required in these frequency bands.**France is indoor use only in the upper end of the band.The requirements for any country may change at any time. Xirrus recommends that you check with local authorities for the current status of their national regulations for both 2.4 GHz and 5 GHz wireless LANs.The following countries have additional requirements or restrictions than those listed in the above table:BelgiumThe Belgian Institute for Postal Services and Telecommunications (BIPT) must be notified of any outdoor wireless link having a range exceeding 300 meters. Xirrus recommends checking at www.bipt.be for more details.Draadloze verbindingen voor buitengebruik en met een reikwijdte van meer dan 300 meter dienen aangemeld te worden bij het Belgisch Instituut voor postdiensten en telecommunicatie (BIPT). Zie www.bipt.be voor meer gegevens.Frequency Band (MHz)Max Power Level (EIRP) (mW) Indoor Outdoor 2400–2483.5 100 X X **5250–5350 *200 X N/A5470–5725* 1000 X X
Wireless Access Point569Les liasons sans fil pour une utilisation en extérieur d’une distance supérieure à 300 mèters doivent être notifiées à l’Institut Belge des services Postaux et des Télécommunications (IBPT). Visitez www.bipt.be pour de plus amples détails.GreeceA license from EETT is required for the outdoor operation in the 5470 MHz to 5725 MHz band. Xirrus recommends checking www.eett.gr for more details.Η δη ιουργβάικτ ωνεξωτερικο ρουστη ζ νησυ νοτ των 5470–5725 ΜΗz ε ιτρ ετάιωνο ετάά όάδειά της ΕΕΤΤ, ου ορηγεβτάι στερά ά ό σ φωνη γν η του ΓΕΕΘΑ. ερισσότερες λε τομ ρειεωστο www.eett.grItalyThis product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table for Italy. Unless this wireless LAN product is operating within the boundaries of the owner’s property, its use requires a “general authorization.” Please check with www.communicazioni.it/it/ for more details.Questo prodotto é conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all’interno del proprio fondo, l’utilizzo di prodotti wireless LAN richiede una “autorizzazione Generale.” Consultare www.communicazioni.it/it/ per maggiori dettagli.Norway, Switzerland and LiechtensteinAlthough Norway, Switzerland and Liechtenstein are not EU member states, the EU Directive 1999/5/EC has also been implemented in those countries.Calculating the Maximum Output Power The regulatory limits for maximum output power are specified in EIRP (radiated power). The EIRP level of a device can be calculated by adding the gain of the antenna used (specified in dBi) to the output power available at the connector (specified in dBm).
Wireless Access Point570AntennasThe Xirrus Wireless Array employs integrated antennas that cannot be removed and which are not user accessible. Nevertheless, as regulatory limits are not the same throughout the EU, users may need to adjust the conducted power setting for the radio to meet the EIRP limits applicable in their country or region. Adjustments can be made from the product’s management interface — either Web Management Interface (WMI) or Command Line Interface (CLI).Operating FrequencyThe operating frequency in a wireless LAN is determined by the access point. As such, it is important that the access point is correctly configured to meet the local regulations. See National Restrictions in this section for more information.Russia CU Approval (XR-2000/4000 Series)For the Xirrus XR-2000 and XR-4000 Series Wireless Arrays, the approval mark is affixed to the equipment:If you still have questions regarding the compliance of Xirrus products or you cannot find the information you are looking for, please contact us at:Xirrus, Inc.2101 Corporate Center DriveThousand Oaks, CA 91320USATel: 1.805.262.16001.800.947.7871 Toll Free in the USFax: 1.866.462.3980www.xirrus.com
Wireless Access Point571Compliance Information (Non-EU)This section contains compliance information for the Xirrus Wireless Array family of products. The compliance information contained in this section is relevant to the listed countries (outside of the European Union and other countries that have implemented the EU Directive 1999/5/EC). Declaration of Conformity—Mexico, ThailandThis Appendix contains Notices, Warnings, and Compliance information for these indoor model series: XR-1000, XR-2000, XR-4000, and XR-6000. This includes the models just listed whether or not they have been upgraded to have IEEE 802.11ac Wave2 wireless capability by replacing existing radios with XI-AC3470 modules.For Notices, Warnings, and Compliance information for other models, see the notes at the beginning of this chapter. Mexico XR-1000, XR-2000, XR-4000, XR-6000/7000 Dictamen #: 1402D00741 Models with 2x2 radios: Cofetel Cert #: RCPXIXI13-0807Models with 3x3 radios: Cofetel Cert #: RCPXIXI13-0808Thailand This telecommunication equipment conforms to NTC technical requirement.
Wireless Access Point572Declaration of Conformity—BrazilXR-1000 XR-2000XR-4000
Wireless Access Point573Safety WarningsTranslated safety warnings appear on the following page. This Appendix contains Notices, Warnings, and Compliance information for these indoor model series: XR-1000, XR-2000, XR-4000, and XR-6000. This includes the models just listed whether or not they have been upgraded to have IEEE 802.11ac Wave2 wireless capability by replacing existing radios with XI-AC3470 modules.For Notices, Warnings, and Compliance information for other models, see the notes at the beginning of this chapter. !Safety WarningsRead all user documentation before powering this device. All Xirrus interconnected equipment should be contained indoors. This product is not suitable for outdoor operation. Please verify the integrity of the system ground prior to installing Xirrus equipment. Additionally, verify that the ambient operating temperature does not exceed 50°C.!Explosive Device Proximity WarningDo not operate the XR Series Wireless Array near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.!Lightning Activity WarningDo not work on the XR Series Wireless Array or connect or disconnect cables during periods of lightning activity.!Circuit Breaker WarningThe XR Series Wireless Array relies on the building’s installation for over current protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A (U.S.) or 240 VAC, 10A (International) is used on all current-carrying conductors.
Wireless Access Point574Translated Safety WarningsAvertissements de SécuritéThis Appendix contains Notices, Warnings, and Compliance information for these indoor model series: XR-1000, XR-2000, XR-4000, and XR-6000. This includes the models just listed whether or not they have been upgraded to have IEEE 802.11ac Wave2 wireless capability by replacing existing radios with XI-AC3470 modules.For Notices, Warnings, and Compliance information for other models, see the notes at the beginning of this chapter. !SécuritéLisez l'ensemble de la documentation utilisateur avant de mettre cet appareil sous tension. Tous les équipements Xirrus interconnectés doivent être installés en intérieur. Ce produit n'est pas conçu pour être utilisé en extérieur. Veuillez vérifier l'intégrité de la terre du système avant d'installer des équipements Xirrus. Vérifiez également que la température de fonctionnement ambiante n'excède pas 50°C (40°C pour XR-520).!Proximité d'appareils explosifsN'utilisez pas l'unité XR Wireless Array à proximité d'amorces non blindées ou dans un environnement explosif, à moins que l'appareil n'ait été spécifiquement modifié pour un tel usage.!FoudreN'utilisez pas l'unité XR Wireless Array et ne branchez pas ou ne débranchez pas de câbles en cas de foudre.
Wireless Access Point575!DisjoncteurL'unité XR Wireless Array dépend de l'installation du bâtiment pour ce qui est de la protection contre les surintensités. Assurez-vous qu'un fusible ou qu'un disjoncteur de 120 Vca, 15 A (États-Unis) ou de 240 Vca, 10 A (International) maximum est utilisé sur tous les conducteurs de courant.
Wireless Access Point576Software License and Product Warranty AgreementFor Software License and Product Warranty information, please see http://www.xirrus.com/support/eula/.Hardware Warranty AgreementFor the Hardware Warranty Agreement, please see http://www.xirrus.com/support/eula/.

Navigation menu