CELLUON PICOPRO Pico projector User Manual

CELLUON, INC. Pico projector

User Manual

1. Safety PrecautionsThis product is not waterproof – avoid using it near water or wet places.There is a risk of malfunction if product is used in places where sudden or extreme temperature changes occur.Applying excessive force or impact to this product may result in product damage, and will void warranty.Never attempt to disassemble or service this product yourself. Doing so can result in electrical shock and void warranty.This is a Class 3R Laser product. For your safety, do not stare directly into the laser source. Doing so could damage your eyes.FCC Compliance InformationThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference to another device.2. This device must accept any interference received, including interference that may cause undesired operation.FCC Class NoticeThis equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to Part15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment.This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur with special installation.If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:■ Reorient or relocate the receiving antenna.■ Increase separation between the equipment and receiver.■ Connect the equipment to an outlet on a circuit different from which the receiver is connected.■ Consult the dealer or an experienced radio/TV technician.FCC CautionAny changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.FCC RF Radiation Exposure Statement:This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Industry Canada StatementThis device complies with Industry Canada license- exempt RSS standard(s). Operation is subject to the following two conditions:1. This device may not cause interference.2. This device must accept any interference, including interference that may cause undesired operation of the device.CE CautionRisk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.IEC-60825-1 CautionUse of control or adjustments or performances of procedures other than those specified here in may result in hazardous radiation exposure.8. Making AdjustmentsVolume AdjustmentVolume is controlled directly from PicoPro.Locate touch volume control area on top of device. Adjust the volume by lightly touching on the + or – pattern.Speaker / Earphone UsagePlease connect a speaker or an earphone to the 3.5mm audio out jack. Laser AlignmentWhen the images seem blurry and/or the colors appear skewed, please visit Celluon website at www.celluon.com/support.php5. Product FeaturesPicoPro is a laser-based pico projector that fits in your pocket for a superior portability. It allows you to project contents in your mobile devices onto any surface via HDMI connection or Miracast screen mirroring capability. 6. Identifying PartsTouch-sensitive Volume UpTouch-sensitive Volume DownBacklit Battery Indicator Light SpeakerMHL/HDMI cable input3.5mm Audio OutBattery Status IndicatorCHARGE – Micro USB port for chargingPower ButtonMode Switch ButtonReset ButtonFCC ID : TCLPICOPRO CE1177 KC : MSIP-CMM-CLK-PICOPROIC : 10211A-PICOPROModel : PicoPro DC : 5V 2A Celluon, Inc. Made in Korea4. Package ContentsPicoPro User ManualPowerAdapterHDMI/MHL cableSamsungmicroUSBAdapter Tripod PouchThe perceived brightness of laser projectors with a given ANSI brightness is 50%+ higher than that of the LED based projectorsBrightness150 x 73 x 13.4 mm(6 x 3 x 0.5 inches)181g( 0.4lbs )Wireless Connection: 2+ hrsWired Connection: up to 3 hrsSizeMeasurementWeightThe operating time may vary depending on the environment of useBattery Operation TimeDownload of DLNA streaming application required for DLNA connectioniOSItem Spec. RemarkProduct LifetimeFocusMax. Image (Screen) SizeSequential Contrast RatioDisplay PerformanceResolutionAspect ratioSpeakerElectrical CharacteristicsAudio InterfaceWirelessClassificationLaser SafetyOperating TemperatureEnvironmental ConditionWired ConnectionAndroid/Windows OSiOSCompatibility Wireless ConnectionAndroid/Windows OSThrow RatioColor Depth30 ANSI lumensDLNALaser10,000 hoursInfinite Focus (always in focus) No focus wheel required250 inches In optimal lighting conditions80,000 : 11920 x 720p HD resolution16:91.0 W3.5mm ear phone jackDual (2.4G, 5G)IEC Class 2, Edition 3 Consumer safe device0°C - 35°CMicro HDMI/MHL cable Micro HDMI Additional Apple Lightning Digital AV Adapter requiredMiracast Screen Mirroring1.1 Big screen at a short distance1.67M colors (R/G/B 24bit)11. SpecificationsNo signal when a device is connected via HDMI cable Please make sure the cables are inserted into the correct port. Please note that different devices require different gender/adapter to convert to micro HDMI compatible.Mobile device cannot find Celluon PicoPro during Miracast connection searchPlease make sure PicoPro is on Miracast mode. This may also be due to a particularly heavy wireless traffic. If this is the case, please reset the device by pressing the reset button on the back of device.Cannot stream contents through DLNA application Please make sure device’s WiFi is properly connected to PicoPro’s WiFi. For DLNA connection, please make sure to connect using the password “12345670”It takes a long time to display contents through DLNA modeIt depends on each DLNA streaming app to project contents through PicoPro. For large media files, it may take some time to load and convert the video to correct format.PicoPro is connected, but only the black screen isprojected from the devicePlease check if the connected mobile device is on sleep mode. If the screen of the connected device goes black, the projected screen will go black as well. Note that if the volume control LED patterns are on, the PicoPro is powered on.There is no sound Please make sure the volume level of the PicoPro and/or connected device is not in the mute status. Product makes abnormal noises Please contact Celluon Customer Service for further assistanceThe projected image is unclear This is due to the shifts in laser diode. Please refer to Laser Alignment instruction page to adjust shifted lasers.Connection through Miracast intermittentlydisconnects during useThis is due to the noise occurred by double wireless connection. Try to connect again after disconnecting all the previously connected wireless networks.The video stops playing periodically Please make sure connected device has enough battery to play the video. If both devices have enough battery, this may be due to unstable WiFi connection. Please disconnect and reconnect the device.Device automatically shuts down during use This may be due to the depletion of battery or high temperature of the product. If the product is left in a place where the enviornmental temperature ishigh (such as in a blanket or near heater), the power will turn off automatically in protection of fire hazard. Please cool the product and use it withinspecified operating temperature before turning it on again. If the product has been shut down due to the depletion of battery, please charge the devicebefore turning it back on.PicoPro is frozen; it stopped playing the video / no response from buttons when pressed / cannot convert modesPlease reset the device by pressing the reset button on the back of device. (Refer to “Identifying Parts” section for the location of reset button.)10. Troubleshooting12. Warranty■ Celluon warrants this product to be free from defects in materials and workmanship under normal use for a period of one (1) year from the date of purchase, as evidenced by the receipt of purchase.■ During the warranty period, Celluon shall repair or replace the product if defective. If replaced, the replacement shall be with a product of equal or greater value. ■ This warranty is limited to the purchaser and is not transferable.Please contact support@celluon.com for warranty supports.3. Environmentally Friendly Disposal and RecyclingTo protect the environment, dispose this product separately from household waste once it has reached its end of life, or take it to your local electronic waste disposal center.Built-in BatteryUse supplied USB power adapter to begin charging the battery. Battery status is indicated by four blue LED indicators while charging. (4 LED : 100% / 3 LED : 75% / 2 LED : 50% / 1 LED : 25%)3140 mAh @ 3.7VBattery CapacityApprox. 150 minutes (with continuous use)Battery Operating TimeRechargeable Lithium-ion Polymer BatteryBattery TypeApprox. 270 minutesBattery Charging TimeCharging the BatteryKC : MSIP-CMM-CLK-PICOPRO FCC ID : TCLPICOPRO CE1177compliantRoHS IC No : 10211A-PICOPROCLASS 3R LASER PRODUCTIEC-60825-1 : Class 3R Laser2. Certifications7. Connecting PicoProa. Compatible Operating SystemsAny digital devices that support HDMI capabilityMiracast DLNAFor Wireless ConnectionAndroid OS 4.2 or laterWindows OS 8.1 or laterAny OS that supports Screen Mirroring functionalityAny digital devices that support DLNA protocol * Using DLNA connection requires downloading DLNA streaming app from the App Store or Play Store.For HDMI Connection** Booting up time make take up to 3 seconds.From Miracast mode to DLNA / DLNA mode to Miracast1. From Miracast mode, lightly press “Mode Switch” button.2. “Ready to Connect” screen for DLNA mode will display.* For Apple devices, please use additional Apple digital AV adapter to connect via HDMI cable.* For Samsung devices, please use supplied Samsung adapter (5pin to 11pin converter) to connect to MHL/HDMI cable.b. Wired ConnectionUsing HDMI Connection :Use plug-n-play connection for any digital/mobile device via HDMI connection.1. Turn on PicoPro by pressing the power button for about 2-3 seconds.2. Celluon logo will display upon power on.3. After the logo, “Preparing wireless connection… To go to HDMI mode, press Mode Switch button” screen will display.4. Press and hold “Mode Switch” button located next to power button for 2~3 seconds to change to HDMI mode.5. PicoPro is now in HDMI mode.6. Locate MHL/HDMI port on the PicoPro and use supplied HDMI cable to connect to a device.7. PicoPro will start mirroring contents from connected device.d. Switching Connection ModePicoPro allows you to easily switch from wired connection mode to wireless mode, and vice versaFrom HDMI mode to Miracast mode1. From HDMI mode, pressand hold “Mode Switch” button for about 2 seconds.3. After the logo, “Preparing wireless connection… To go to HDMI mode, press Mode Switch button” screen will display.4. After about 20-30 seconds, “Ready to Connect” screen will display for Miracast connection, indicating that the mode is successfully switched. 2. Celluon logo will display.From Miracast mode to HDMI mode1. From Miracast mode, pressand hold “Mode Switch” button for about 2 seconds.2. Celluon logo will display shortly, and “Please connect using HDMI cable or press Mode Switch button to change to wireless mode” screen will display.3. Use HDMI cable to connect device.Using DLNA : * To connect to devices using DLNA capability, you must install a DLNA streaming app on your mobile device. Apps can be downloaded from AppStore/GooglePlay 1. Turn on PicoPro by pressing power button for 2-3 seconds.2. Celluon logo will display upon power on.3. After the logo, “Preparing wireless connection… To go to HDMI mode, press Mode Switch button” screen will display.4. After about 20-30 seconds, “Ready to Connect” screen for Miracast will display. (Default wireless connection mode is Miracast)5. Lightly press “Mode Switch” button again to change to DLNA mode.6. DLNA “Ready to Connect” screen will display upon completion of mode switch.7. On a desired mobile device, go to WiFiseting, and connect to “Celluon PicoPro”. Use password “12345670” to connect.8. When Wifi is successfully connected, open the installed DLNA streaming application on the mobile device.9. Select desired content to display.10. Select display location: Celluon PicoPro.11. Mobile device will say “Connected” and PicoPro will start display selected media contents.c. Wireless ConnectionUsing Miracast : The Miracast capability is called different names on difference devices. (Samsung/Sony – Screen Mirroring , HTC – Media Output) Please find this capability in the settings app on the device.1. Turn on PicoPro by pressing power button for 2-3 seconds.2. Celluon logo will display upon power on.3. After the logo, “Preparing wireless connection… To go to HDMI mode, press Mode Switch button” screen will display.4. After about 20-30 seconds, “Ready to Connect” screen for Miracast will display.5. On a desired mobile device, find and select Screen Mirroring / Media Output.6. Mobile device will search for nearby devices to connect.7. When device discovers “Celluon PicoPro”, tab to connect.8. Mobile device will say “Connected” and PicoPro will start mirroring display.*** For DLNA connection with iOS devices:1. Follow above steps 1-7.2. Find AirPlay option on device’s status bar.3. Tab AirPlay and select “Celluon AirPico” for display location.4. Select a photo/video/music to share through PicoPro.9. Charging the PicoPro1. Locate micro USB port next to the battery status button.2. Use the supplied AC adapter to charge the PicoAir thought the micro USB port.■ Please fully charge PicoPro’s internal battery before first use (approximately 3 to 5 hours).■ A low battery warning icon will show on the screen when the battery is low. ■ Use the included power adapter to charge your PicoPro. If the battery is too low, PicoPro will automatically shut off.Battery StatusFirst three LED indicators remain solid. When charging at this stage, the fourth LED indicator will blink to indicate it is being charged.All four LED indicators will remain solid.100% chargedVolume control + & - sensors will blink to indicate low battery status0% chargedDescriptionStatusLED Indicator75% chargedFirst two LED indicators remain solid. When charging at this stage, the third LED indicator will blink to indicate it is being charged.50% chargedFirst LED indicator remains solid. When charging at this stage, the second LED indicator will blink to indicate it is being charged.25% charged3+ hrs4-5 hoursWired Connection (HDMI/MHL)2.5+ hrsWireless Connection (Miracast / DLNA)Charging Time Operating Time Table of Contents1. Safety Precautions FCC Compliance Information FCC Class Notice FCC Caution FCC RF Radiation Exposure Statement Industry Canada Statement CE Caution IEC-60825-1 Caution 2. Certifications3. Environmentally Friendly Disposal and Recycling4. Package Contents 5. Product Features6. Identifying Parts7. Connecting PicoPro a. Compatible Operating Systems b. Wired Connection c. Wireless Connection d. Switching Connection Mode8. Making Adjustments a. Volume Adjustment b. Speaker / Earphone Usage c. Laser Alignment9. Charging the PicoPro10. Troubleshooting 11. Specifications12. Warranty

Navigation menu