CDVI WIRELESS S P A S3RT Part 15 Security / Remote Control Transmitter User Manual PWJS3RT UserMan

CDVI WIRELESS S.P.A. Part 15 Security / Remote Control Transmitter PWJS3RT UserMan

PWJS3RT_UserMan

The Installer’s Choicewww.cdvi.cawww.cdvi.ca1 - INTRODUCTIONThe remote control RADIUM R1 - R2 - R4 is a 1-2-4 buons key chain style transmier, operang at 433,92 MHz. It has been designed for the control of automac closing systems and an-burglar systems, thanks to its very high security coding system (KeeLoq® Hopping code). The code sent by the transmier changes at each acvaon, avoiding any scanning and copying risk. A special algorithm allows to keep synchronized transmier and receiver. The transmier can be equipped with passive tag ( see table for the reference ) The CR 2016 lithium baeries of the transmier have a shelf life of about 6 months. The product fully complies with Part 15 of FCC Regulaons and the European Direcves 2006/95/CE, 2004/108/CE, 99/05/CE.2 - TECHNICAL SPECIFICATIONSOperang frequency: 433,92 MHzNumber of buons: 1-2-4 Baery: 2 x 3V lithium CR2016Baery life: 18 to 24 monthsSecurity code: Keeloq® Hopping codeNumber combinaons: 2exp64Operang temperature: -20°F to +131°F Overall dimensions: 2.83”x 1.4”x 0.47” Weight: 0.49 oz. (14 gr.)RadiumRemote controlR1 R2 R4P/N Descripon Tag ( 125 KHz )R1 1 Buon Remote -R1H 1 Buon Remote HIDR1P 1 Buon Remote ParadoxR1C 1 Buon Remote CDVIR2 2 Buons Remote -R2H 2 Buons Remote HIDR2P 2 Buons Remote ParadoxR2C 2 Buons Remote CDVIR4 4 Buons Remote -R4H 4 Buons Remote HIDR4P 4 Buons Remote ParadoxR4C 4 Buons Remote CDVI3 - PRODUCT RANGEWIRELESS TECHNOLOGY
The Installer’s Choice8 - BATTERY ACCESS To access the baery slide out the baery door as shown in gure. Slide out the 2 old baeries and replace them with the new ones [CR2016] respecng the polarity, with the posive (+) side upward. NOTE: Please dispose of the baeries properly according to local laws and regulaons. Test proper baery instal-laon by verifying that the LED illuminates when the buon is pushed.4 - NUMBERING Each transmier is manufactured and sold with a die-rent factory-set serial number.6 - PROGRAMMING The transmier must be programmed into your system memory.7 - OPERATION A - Firmly depress the buon unl the small red BLUE illuminates.B - Aer the LED has illuminated, release the buon. If the device you are aempng to acvate does not re-spond, repeat steps A and B or consult secon 9 ( Troubleshoong ) of this manual.9 - TROUBLESHOOTING PROBLEM SOLUTIONThe system does not receive the transmier signal.The transmier LED is ONCheck to verify if the remote is programmed into your systemThe operang range is reducedThe transmier LED is blinkingLow baery : replace baeriesThe system does responds.The transmier LED is OFFBaery empty : replace baeries5 - MAIN COMPONENTSThis device complies with Part. 15 of the FCC Rules Operaon is subject to the following two condions:(1) This device may not cause harmful interference, and (2) this device must accept interference received, including inter-ference that may cause undesired operaon.FCC ID : PWJS3RTNoceAny changes or modicaon to CDVI equipment not expressly approved by CDVI could void the manufacturer’s warranty.Buon ABuon BBuon C Buon DBaery door2 x CR2016Blue LEDKey ringSlide to openCDVI 1637 Highway 440 West, Laval, Québec, Canada, H7L3W3 Tel: (450) 682-7945, Toll Free Tel: 1-866-610-0102, Fax: (450) 682-9590, Toll Free Fax: 1-866-682-9590Manufactured by: CDVI WirelessMade in ITALYWARRANTYThe warranty period for this product is 60 months, beginning from the manufacturer date. During this period, if the product does not work correctly, due to a defecve component, the product will be repaired or substuted at our discreon. The guarantee does not cover the plasc container integrity. Aer-sale service is supplied at the factory.IS-T15CDUK Rev. 0 15/1/2014This EUT is in compliance with MPE for general populaon / uncontrolled exposure limits and it had been tested in accordance with the measurement methods and procedures specied in FCC 47 CFR § 1.1310 and 2.1091 .To sasfy FCC RF exposure requirements for mobile transming devices, a separaon distance of 20 cm or more should be maintained between the antenna of this device and persons during device operaon. To ensure compliance, operaons at closer than this distance are not recommended. The antenna used for this transmier must not be co-located in conjuncon with any other antenna or transmier.

Navigation menu