CDVI WIRELESS S P A GDR RECEIVER - GDR User Manual IS GDRUAUK

CDVI WIRELESS S.P.A. RECEIVER - GDR IS GDRUAUK

Users Manual

SENTRY GARAGE DOOR RECEIVER3 - WIRINGS4 - OPERATING MODESLD STEADY ON : PULSE ModeLD BLINKING : LATCH Mode The operating mode can be Pulse or Latch according the following diagram.LD gives the operating mode. To display the current operating mode push P1 for 4 sec 5 - OPERATING MODE SETTINGP1LD4sProcedure1) Press and hold the push-button P1 for 4 sec. until the green led LD comes ON ( Fig. 3); the led display the current operating mode according to par. 4.To modify push again P1 and release it within 1 sec.: once released P1: · from steady ON it will begin to blink ( Latch mode );· from blinking it will come steady ON ( Pulse mode ).LDP11sLDLDP11sFig. 3P1AntennaRelay NO OutputPower supply 22Receiver type SuperheterodyneCarrier Frequency 433.92 MHzLocal oscillation frequency 6.6128 MHzDemodulation AM/ASKLocal oscillator type VCO / PLLChannel width > 25 KHzIntermediate frequency 10.7 MHzInput sensitivity -115 dBmSpurious emissions < -57 dBmInput load 50 OhmOperating voltage 9 VdcMax power on relay contacts 24 VARelay number 1Operating modes Pulse / Latch Max activation delay 300 mS Memory 100 TXSecurity protocol Fixed Code9Code combinations 3Operating temperature -4°/+158°FEnclosure IP grade IP2XDimensions ( main box) 1.57 x 0.9 x 2.2 in2 - TECHNICAL SPECIFICATIONS1 - INTRODUCTIONThe Sentry Garage Door Receiver ( #030209) is single conversion superheterodyne receiver oeperating at 433,92 MHz in AM/ASK modulation.It is designed for automatic closing systems and anti-burglar systems. The antenna is direct connected with 6,5” wire .The relay K1 available output is only with NO type contact The operating mode of K1 is Pulse and or Latch ( see below for its configuration). The power supply is 9 Vdc provided by its own 9 Vdc / 300 mA external power supply. The IP grade of 2X allows only indoor installations.The product fully complies with the EMC European Regulations (CE) and the FCC Part 15 Regulations. Use and installation manualThank you for choosing this product . You are recommended to read this manual carefully before installing this product.Made in Italy #030209
4 - MEMORIZZAZIONE DEI TRASMETTITORIIf the memory is full when you try to memorize one more transmitter LD flashes 3 times and the procedure ends.8 - ERASING TRANSMITTERS FROM THE MEMORY 4 - MEMORIZZAZIONE DEI TRASMETTITORI6 - PROGRAMMING TRANSMITTER AND RECEIVERP1LD4sLD7 - MEMORY FULLProcedure1) Press and hold the push-button P1 for 4 sec. until the green led LD comes ON ( Fig. 4); the led display the current operating mode according to par. 4.2) Press the transmitter button down : LD switches OFF and ON again, waiting for another tx to memorize;3) If within 10 sec. no more transmitters are activated, LD switches OFF and the procedure is over. P1 4sFast blinkingBlinks: LatchSteady ON: PulseProcedure1) Press and hold the push-button P1 for 4 sec. until the green led LD comes ON ( Fig. 5); the led display the current operating mode according to par. 4.2) Press and hold P1 for more 4 sec. : LD begins to blink fast. At this point you can do 2 different operations:A ) DELETE THE SINGLE TRANSMITTER Press the button down of the transmitter to delete. LD flashes twice slow and then begins again to blink fast for more tx to delete. If within 10 sec. no more transmitters are activated, LD switches OFF and the procedure is over. B ) ERASE ALL THE MEMORYPress and hold P1 for more 4 sec. : LD makes 3 slow flashes then switches off and the procedure ends. P1IS-GDRUAUK Rev. 3 del 10/06/2008AFig. 4P110 Sec.LD4sTXLD LDATXP1 4sLD10 Sec.LDLD LD2 slowflashesLDFast blinking End3 slowflashes EndFig. 5EndUSAutomatic LTD118 Hillside Drive Lewisville, TX 750571-866-711-0001www.sentrygateopener.comWARRANTYUSAutomatic, LTD warrants this product to be free of defects in materials and workmanship for 2 YEAR. For a period of 2 YEAR following purchase USAutomatic, LTD. will repair or replace the product free of charge, including parts, shop labor and return shipping and handling. This 2 YEAR warranty does not cover the plastic case from normal wear or damage due to misuse of the receiver or transformer. Modifications to the supplied transformer will void the warranty.To have the product sent for warranty consideration, it must be returned with the proof of purchase and a return authorization number. To obtain a return authorization number please visit or call 1-888-711-0001 for assistance.The return authorization number must be clearly marked on the outside of the return package or it may not be accepted.www.sentrygateopener.comFCC ID : PWJGDRThis device complies with FCC Rules . Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation.Part. 15 of the Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Navigation menu