Broadcom BRCM1030 802.11g WLAN PCI-E Mini Card User Manual book

Broadcom Corporation 802.11g WLAN PCI-E Mini Card book

User Manual

www.dell.com | support.dell.comDell™ Studio 1535/1536Quick Reference GuideModel PP33L
Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.If you purchased a Dell™ n Series computer, any references in this document to Mcrosoft® Windows® operating systems are not applicable.___________________Information in this document is subject to change without notice.© 2008 Dell Inc. All rights reserved.Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.Trademarks used in this text: Dell, the DELL logo, Wi-Fi Catcher, YOURS IS HERE, DellConnect, and MediaDirect are trademarks of Dell Inc.; Intel and Core are registered trademarks of Intel Corporation.; AMD, AMD Turion, Athlon, Sempron, ATI Radeon and combinations thereof are trademarks of Advanced Micro Devices, Inc.; Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries; Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell under license. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.Model PP33LMarch 2008 P/N F434C Rev. A00
Contents 3ContentsFinding Information . . . . . . . . . . . . . . . . . . . . 71 About Your Computer . . . . . . . . . . . . . . . . 9Front and Right View . . . . . . . . . . . . . . . . . . . 9Back and Left View . . . . . . . . . . . . . . . . . . . 15Bottom View . . . . . . . . . . . . . . . . . . . . . . . 19Removing and Replacing the Battery . . . . . . . . . . 20Removing and Replacing the Base Cover . . . . . . . 212 Specifications . . . . . . . . . . . . . . . . . . . . . 233 Troubleshooting . . . . . . . . . . . . . . . . . . . 33Dell Technical Update Service . . . . . . . . . . . . . 33Pre-Boot Self-Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics . . . . . . . . 33Dell Support Center . . . . . . . . . . . . . . . . . . . 37Drive Problems . . . . . . . . . . . . . . . . . . . . . 38Hard drive problems . . . . . . . . . . . . . . . . 38Error Messages . . . . . . . . . . . . . . . . . . . . . 39
4ContentsLockups and Software Problems . . . . . . . . . . . . 44The computer does not start . . . . . . . . . . . . 44The computer stops responding . . . . . . . . . . 44A program stops responding or crashes repeatedly . . . . . . . . . . . . . . . . . 44A program is designed for an earlier Microsoft® Windows® operating system . . . . . 45A solid blue screen appears . . . . . . . . . . . . 45Memory Problems . . . . . . . . . . . . . . . . . . . . 45Power Problems . . . . . . . . . . . . . . . . . . . . . 46Troubleshooting Software and Hardware Problems in the Windows Vista® Operating System . . . . . . . 47Restoring Your Operating System . . . . . . . . . . . . 48Using Windows Vista System Restore . . . . . . . 484 Getting Help . . . . . . . . . . . . . . . . . . . . . . . 53Obtaining Assistance . . . . . . . . . . . . . . . . . . 53Technical Support and Customer Service . . . . . 54DellConnect . . . . . . . . . . . . . . . . . . . . . 54Online Services . . . . . . . . . . . . . . . . . . . 54AutoTech Service . . . . . . . . . . . . . . . . . . 55Automated Order-Status Service . . . . . . . . . 55Problems With Your Order . . . . . . . . . . . . . . . . 55Product Information . . . . . . . . . . . . . . . . . . . 55Returning Items for Warranty Repair or Credit . . . . . 56Before You Call . . . . . . . . . . . . . . . . . . . . . 56Contacting Dell . . . . . . . . . . . . . . . . . . . . . 58
Contents 5A Appendix . . . . . . . . . . . . . . . . . . . . . . . . . 59FCC Notice (U.S. Only) . . . . . . . . . . . . . . . . . . 59FCC Class B . . . . . . . . . . . . . . . . . . . . . 59Macrovision Product Notice . . . . . . . . . . . . . . 60Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6Contents
Finding Information 7Finding Information NOTE: Some features may be optional and may not ship with your computer. Some features may not be available in certain countries. NOTE: Additional information may ship with your computer.Document/Media/Label ContentsService Tag and Express Service Code You can find this at the bottom of your computer.• Use the Service Tag to identify your computer when you use support.dell.com or contact support. • Enter the Express Service Code to direct your call when contacting support.Model NumberYou can find this at the bottom of your computer next to the service tag.Model number of your computer.Drivers and Utilities Media• A diagnostic program for your computer• Drivers for your computer• Device documentation• Notebook System Software (NSS)Readme files may be included on your Drivers and Utilities media to provide last-minute updates about technical changes to your computer or advanced technical-reference material for technicians or experienced users.NOTE: Drivers and documentation updates can be found at support.dell.com.Setup Diagram How to setup your computerService ManualAvailable at Dell Support Website -support.dell.com• How to remove and replace parts• How to troubleshoot and solve problemsDell Technology GuideAvailable in Windows Help and Support (Start → Help and Support) and at Dell Support Website - support.dell.com• About your operating system• Using and maintaining peripherals• Understanding technologies such as Internet, E-mail, and so on.
8Finding InformationMicrosoft Windows License LabelYou can find this label in the battery compartment.Your operating system product key.NOTE: This label is available only for systems with Microsoft operating system.Dell Support Center• Self Help (Troubleshooting, Security, System Performance, Network/Internet, Backup/Recovery, and Windows Vista)• Alerts (technical support alerts relevant to your computer)• Assistance from Dell (Technical Support with DellConnect™, Customer Service, Training and Tutorials, How-To Help with Dell on Call, and Online Scan with PC CheckUp)• About Your System (System Documentation, Warranty Information, System Information, Upgrades & Accessories)NOTE: The Dell Support Center features available in your computer depends on the configuration.Dell QuickSet Help Information on network activity, the hotkeys, and other items controlled by Dell QuickSetTo view Dell QuickSet Help, right-click the Dell QuickSet icon in the Windows notification area.Document/Media/Label Contents
About Your Computer 9About Your ComputerFront and Right View458215143691011171820 1719161213
10 About Your ComputerCAMERA INDICATOR —Indicates that the camera is on. Based on configuration selections you made when ordering your computer, your computer may not include a camera.CAMERA —Built-in camera for video capture, conferencing, and chat. Based on configuration selections you made when ordering your computer, your computer may not include a camera. DISPLAY —For more information on the display, see Dell Technology Guide.MEDIA CONTROL BUTTONS —Control CD, DVD, Blu-ray, and Media Player playback.1 camera indicator (optional) 2 camera (optional)3 display 4 media control buttons (9) 5 keyboard 6 num lock light7 device status lights 8 power button 9 AC adapter connector 10 battery status light11 optical drive 12 USB connectors (2) 13 IEEE connector 14 fingerprint reader (optional)15 consumer IR 16 analog microphone 17 touch pad buttons (2) 18 touch pad19 caps lock light 20 digital array microphones (optional)Launch Dell MediaDirect Mute the soundPlay the previous track Turn the volume downStop Turn the volume upPlay or pause Eject the discPlay the next track
About Your Computer 11KEYBOARD —Backlit keyboard is an optional feature. If you have purchased the backlit keyboard, you can change the settings through Dell QuickSet. See Dell Technology Guide for more information on keyboard.NUM LOCK LIGHT —Turns on when Num Lock is activated.DEVICE STATUS LIGHTSThe lights located on the palm rest towards the front of the computer indicate the following:POWER BUTTON —Press the power button to turn on the computer or exit a power management mode. NOTICE: If the computer stops responding, press and hold the power button until the computer turns off completely (may take several seconds). NOTICE: To avoid losing data, turn off your computer by performing a Microsoft® Windows® operating system shutdown rather than by pressing the power button.WiFi status light – Turns on when wireless networking is enabled. To enable or disable wireless networking, use the wireless switch (see "wireless on/off switch" on page 17).Bluetooth® status light – Turns on when a card with Bluetooth wireless technology is enabled.NOTE: The card with Bluetooth wireless technology is an optional feature. The light turns on only if you ordered the card with your computer. For more information, see the documentation that came with your card.To turn off only the Bluetooth wireless technology functionality, right-click the icon in the notification area, and then click Disable Bluetooth Radio. To turn it back on, right-click the icon in the notification area, and then click Enable Bluetooth Radio.To quickly enable or disable all wireless devices, use the wireless switch.Hard drive activity light – Turns on when the computer reads or writes data. NOTICE: To avoid loss of data, never turn off the computer while the light is flashing.
12 About Your ComputerAC ADAPTER CONNECTOR —Attaches an AC adapter to the computer. The AC adapter converts AC power to the DC power required by the computer. You can connect the AC adapter with your computer turned on or off. CAUTION: The AC adapter works with electrical outlets worldwide. However, power connectors and power strips vary among countries. Using an incompatible cable or improperly connecting the cable to the power strip or electrical outlet may cause fire or equipment damage. NOTICE: When you disconnect the AC adapter cable from the computer, grasp the connector, not the cable itself, and pull firmly, but gently to help prevent damage to the cable. NOTE: Plug the power cord and the adapter firmly in, and ensure that the green LED is on.BATTERY STATUS LIGHT —Turns on steadily or blinks to indicate battery charge status.If the computer is connected to an electrical outlet, the battery status light operates as follows:– Solid white: The battery is charging and has attained sufficient charge or the battery is completely charged– Off: The battery is adequately charged (or the computer is turned off).– Solid orange: The battery charge is low.– Flashing orange: The battery charge is critically low.
About Your Computer 13OPTICAL DRIVE —For more information about the optical drive, see Dell Technology Guide. NOTE: The optical drive supports standard circular 12.7 cm discs. Irregularly shaped discs or discs smaller than 12.7 cm are not supported.USB CONNECTORS IEEE 1394 CONNECTOR —Connects devices supporting IEEE 1394a high-speed transfer rates, such as some digital video cameras.FINGERPRINT READER (OPTIONAL)—Helps to keep your Dell™ computer secure. When you slide your finger over the reader, it uses your unique fingerprint to authenticate your user identity. The controlling security management software, DigitalPersona Personal, displays a fingerprint reader icon in the system tray that shows whether the reader is ready for use, and provides convenient access to a few major components and features on its menu. When the reader is ready to scan fingerprints, the reader icon appears normally. Otherwise, a red X displays over the reader icon. The icon also flashes in red color when a fingerprint scan is being processed.For more information on how to activate and use DigitalPersona Personal, click Start → Programs → DigitalPersona Personal. The following sub-items are available in this menu:•Fingerprint Enrollment Wizard - To enroll your fingerprint •Fingerprint Logon Manager - To add, remove or modify properties related to Fingerprint Logons •Import and Export Wizard - To export fingerprint information into a file for the further import on another computer, or for the use as a user-level backup. This functionality allows avoiding the need to re-enter the data when upgrading your computer or while adding a fingerprint reader to a second computer. However, you need to enroll your fingerprints on the computer that you are exporting the DigitalPersona Personal data to. •Properties - To configure DigitalPersona Personal Settings and product behavior. For more information, see DigitalPersona Online Help → Using DigitalPersona Personal Features → General Settings. •Check for Updates - To deliver and install software updates and also for updating options. You must have an Internet connection to use this feature. You can either check for updates manually or automatically. Connect USB devices, such as a mouse, keyboard, or printer.
14 About Your Computer•Help - HTML-based Help.CONSUMER IR — Infrared sensor for using the Dell Travel Remote.ANALOG MICROPHONE —Integrated single microphone for conferencing and chat. NOTE: Analog microphone is present only when you have not ordered for the optional camera and digital array microphones.TOUCH PAD BUTTONS —Use these buttons much like the buttons on a mouse when you use the touch pad to move the cursor on the display.TOUCH PAD —Provides the functionality of a mouse.CAPS LOCK LIGHT —turns on when Caps Lock is activated.DIGITAL ARRAY MICROPHONES —Higher quality built-in microphones for conferencing and chat. These microphones filter noise and provide better sound quality NOTE: Digital array microphones are optional and may not be present in your computer unless you have ordered for the optional camera. Instead, your computer will have an integrated single analog microphone.
About Your Computer 15Back and Left View1 ExpressCard slot 2 8-in-1 media card reader3 headphone connectors (2) 4 microphone connector5 network connector (RJ-45) 6 USB connector7 eSATA connector* 8 VGA connector9 HDMI connector 10 wireless switch11 security cable slot 12 Wi-Fi catcher network locator13 air vents 14 battery* Studio 1535 systems have an additional USB connector instead of an eSATA connector.5678910111213141234
16 About Your ComputerEXPRESSCARD SLOT —Supports one ExpressCard. The computer ships with a plastic blank installed in the slot.8-IN-1 MEDIA CARD READER —Provides a fast and convenient way to view and share digital photos, music, and videos stored on a media memory card. The computer ships with a plastic blank installed in the slot. The 8-in-1 memory card reader reads the following digital media memory cards:• Secure Digital (SD) memory card• Secure Digital Input Output (SDIO) card• MultiMediaCard (MMC)•Memory Stick • Memory Stick PRO • xD-Picture Card • Hi Speed-SD• Hi Density-SDAUDIO CONNECTORSNETWORK CONNECTOR (RJ-45)USB CONNECTORS Attach headphones to the connectorAttach a microphone to the connectorConnects the computer to a network. The two lights next to the connector indicate status and activity for wired network connections.For information on using the network adapter, see the device user’s guide supplied with your computer.Connect USB devices, such as a mouse, keyboard, or printer.
About Your Computer 17ESATA CONNECTOR NOTE: The eSATA connector is available only in Studio 1536.VGA CONNECTORHDMI CONNECTOR —HDMI (High-Definition Multimedia Interface) connector carries an uncompressed all digital signal to produce hi-definition video and audio.WIRELESS ON/OFF SWITCH —Use this switch to rapidly turn off or on any wireless devices such as WLAN cards and internal cards with Bluetooth wireless technology. The wireless switch on your Dell computer uses the Dell Wi-Fi Catcher™ network locator (see "Wi-Fi Catcher™ network locator" on page 18) to scan for wireless networks in your vicinity. The wireless switch is enabled and configured for use when your computer is shipped to you. You can change the settings through Dell QuickSet or the BIOS (system setup program).Connect eSATA compatible storage devices, such as external hard disk drives or optical drives. Connects video devices, such as a monitor.1off Disables wireless devices2on Enables wireless devices12
18 About Your ComputerSECURITY CABLE SLOT —Lets you attach a commercially available antitheft device to the computer.WI-FI CATCHER™ NETWORK LOCATOR —Press this button for a few seconds to scan specifically for wireless networks in your vicinity.The Wi-Fi Catcher Network Locator has a light that operates as follows:- Flashing white: Searching for networks- Solid white for 10 seconds and then turns off: Network found- Off (flashing white turns off after 10 blinks): No signal foundThe Wi-Fi Catcher Network Locator is enabled and configured for use when your computer is shipped to you. For more information on the Wi-Fi Catcher Network Locator and to enable the feature through Dell QuickSet, right-click the QuickSet icon in the notification area, and then select Help.AIR VENTS —The computer uses an internal fan to create airflow through the vents, which prevents the computer from overheating. The fan automatically turns on when the computer gets hot. Fan noise is normal and does not indicate a problem with the fan or the computer. CAUTION: Do not block, push objects into, or allow dust to accumulate in the air vents. Do not store your computer in a low-airflow environment, such as a closed briefcase, while it is running. Restricting the airflow can damage the computer or cause a fire.
About Your Computer 19Bottom ViewBATTERY —When a battery is installed, you can use the computer without connecting the computer to an electrical outlet. NOTE: Connecting the computer to an electrical outlet through the AC adapter will present the brightest picture as well as charge the battery.BATTERY CHARGE/HEALTH GAUGE —Provides information on the battery charge.BATTERY RELEASE LATCH —Releases the battery.BASE COVER —Compartment that contains the processor, hard drive, memory modules, WLAN, WWAN, or Ultra Wideband (UWB) cards.1 battery 2 battery charge/health gauge3 battery release latch 4 base cover3 41 2
20 About Your ComputerRemoving and Replacing the Battery CAUTION: Using an incompatible battery may increase the risk of fire or explosion. Replace the battery only with a compatible battery purchased from Dell. The battery is designed to work with your Dell computer. Do not use batteries from other computers with your computer. CAUTION: Before performing these procedures, turn off the computer, disconnect the AC adapter from the electrical outlet and the computer, disconnect the modem from the wall connector and the computer, and remove any other external cables from the computer. NOTICE: You must remove all external cables from the computer to avoid possible connector damage. NOTICE: If you choose to replace the battery with the computer in Sleep state, you have up to 1 minute to complete the battery replacement before the computer shuts down and loses any unsaved data.To remove the battery:1Ensure that the computer is turned off.2Turn the computer over.3Slide the battery release latch toward the side of the computer until it is engaged.4Slide the battery out of the bay.To replace the battery, slide the battery into the bay until it clicks into place.1 battery 2 battery release latch21
About Your Computer 21Removing and Replacing the Base Cover CAUTION: Before working inside your computer, follow the safety instructions that shipped with your computer. CAUTION: Before performing this procedures, turn off the computer, disconnect the AC adapter from the electrical outlet and the computer, disconnect the modem from the wall connector and the computer, and remove any other external cables from the computer. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer).To remove the base cover:1Ensure that the computer is turned off.2Remove the battery (see "Removing and Replacing the Battery" on page 20).3Loosen the six captive screws on the base cover and lift the cover off the computer at an angle as shown in the picture. CAUTION: Do not touch the processor thermal-cooling assembly. Processor components should be removed only by trained support personnel.For instructions on removal and replacement of parts, see the Service Manual at support.dell.com.To replace the base cover:1Align the tabs on the base cover to the bottom of the computer.2Replace and tighten the six captive screws on the base cover.3Replace the battery (see "Removing and Replacing the Battery" on page 20).
22 About Your Computer1 base cover 2 captive screws (6)3 tabs 4 SIM card slot2134
Specifications 23Specifications NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start , click Help and Support, and then select the option to view information about your computer.ProcessorProcessor type Studio 1535:•Intel® Celeron™Processor•Intel® Pentium™ Processor•Intel® Core™ 2 ProcessorStudio 1536:•AMD® Sempron™ Processor•AMD® Athlon™ Dual Core Processor•AMD® Turion™ Dual Core Processor•AMD® Turion™ Ultra Dual Core ProcessorL1 cache 64 KB (Intel - 32 KB per core)256 KB (AMD - 128 KB per core)L2 cache 512 KB (AMD Sempron)1 MB (Intel Pentium, Intel Celeron, AMD Athlon, AMD Turion)2 MB or 3 MB (Intel Core 2 Duo, AMD Turion Ultra)6 MB (Intel Core 2 Duo)External bus frequency HyperTransport (AMD)533 MHz (Intel Celeron, Intel Pentium Dual Core)667 MHz/800 MHz (Intel Core 2 Duo)2.66 GHz (AMD Turion Ultra Dual-Core)
24 SpecificationsSystem InformationSystem chipset Intel GM/PM 965 (Studio 1535)AMD M780G (Studio 1536)Data bus width 64 bitsDRAM bus width dual-channel (2) 64-bit busesProcessor address bus width 32 bits Flash EPROM 2 MBGraphics bus PCI-E X16PCI bus 32 bitsExpressCardNOTE: The ExpressCard slot is designed only for ExpressCards. It does NOT support PC Cards.ExpressCard controller Intel ICH8M (Studio 1535)AMD M780G (Studio 1536)ExpressCard connector one ExpressCard slot (54 mm)Cards supported ExpressCard/34 (34 mm) ExpressCard/54 (54 mm)1.5 V and 3.3 VExpressCard connector size 26 pins
Specifications 258-in-1 Memory Card Reader8-in-1 memory card controller Ricoh R5C8338-in-1 memory card connector 8-in-1 combo card connectorCards supported• Secure Digital (SD)•SDIO• MultiMediaCard (MMC)•Memory Stick• Memory Stick PRO• xD-Picture Card• Hi Speed-SD• Hi Density-SDMemoryMemory module connector two user-accessible SODIMM connectorsMemory module capacities 512 MB, 1 GB, 2 GBMemory type 800 MHz SODIMM DDR2Minimum memory 512 MB (single channel)Maximum memory 4 GB (dual channel 2G x2)NOTE: In order to take advantage of the dual channel bandwidth capability, both memory slots must be populated and must match in size.NOTE: The available memory displayed does not reflect the complete maximum memory installed because some memory is reserved for system files.Ports and ConnectorsAudio microphone connector, two stereo headphone/speakers connectorIEEE 1394a 4-pin serial connector (optional)Consumer IR sensor compatible with Philips RC6 (receive only)Mini Card two Type IIIA Mini Card slots, one half-size Mini Card slotNetwork adapter RJ-45 port
26 SpecificationseSATA one four pin eSATA/USB combo connector (available only on Studio 1536)USB four 4-pin USB 2.0-compliant connector (Studio 1535)three 4-pin USB 2.0-compliant connector (Studio 1535)Video 15-hole connectorHDMI 19 pinCommunicationsModem:Ty p eExternal V.92 56K USB ModemControllerHardware modemInterfaceUniversal Serial Bus (USB)Network adapter 10/100/1000 Ethernet LAN on system boardWireless internal WLAN (half-size Mini-Card), WWAN, Mini-Card with Bluetooth® wireless technology, UWB (optional) Mini-CardsWWAN ExpressCardBluetooth® wireless technologyVideoDiscrete:Video typeintegrated on system boardVideo controllerATI Mobility Radeon HD 3450 Video memoryGDDR2 256MB Ports and Connectors (continued)
Specifications 27UMA:Video typeintegrated on system boardVideo controllerMobile Intel GMA X3100, ATI Radeon™ HD 3200 GraphicsVideo memoryIntel: Up to 358 MB of shared memory AMD: Up to 256 MB of shared memory (32 MB dedicated local frame buffer)LCD interfaceLVDSTV supportHDMI 1.2AudioAudio type IDT 92HD73C High Definition Audio codecAudio controller 5.1 channel High Definition AudioStereo conversion 24-bit (analog-to-digital and digital-to-analog)Interfaces:InternalIntel High Definition AudioExternalmicrophone-in connector, two stereo headphones/speakers connectorSpeaker two 4-ohm speakersInternal speaker amplifier 2 Watt per channel into 4 ohmsVolume controls program menus, media control buttonsVideo (continued)
28 SpecificationsDisplayType (TrueLife) 15.4-inch CCFL WXGA Anti-Glare15.4-inch CCFL WXGA+ with TrueLife15.4-inch CCFL WUXGA with TrueLife15.4-inch WXGA+WLED with TrueLifeDimensions:Height207 mm (8.14 in) Width331.2 mm (13.03 in)Diagonal391.2 mm (15.4 in) Maximum resolutions:WXGA AG1280 x 800 at 262 K colorsWXGA+ with TrueLife1440 x 900 at 262 K colorsWUXGA+with TrueLife1600 x 1200 at 262 K colorsRefresh rate 60 HzOperating angle 0° (closed) to 140°Viewing angles:Horizontal±40° (WXGA AG)±55° (WXGA+ with TrueLife) ±55° (WUXGA+ with TrueLife)Vertical+15°/–30° (WXGA AG)±45° (WXGA+ with TrueLife) ±45° (WUXGA+ with TrueLife)Pixel pitch:WXGA AG0.258 mmWXGA+ with TrueLife0.2304 mmWUXGA+with TrueLife0.1725 mmControls brightness can be controlled through keyboard shortcuts (see Dell Technology Guide for more information.)
Specifications 29MediaDrive DVD+/-RWInterface Roxio Creator 10 DE and Roxio Creator 10 Premier - UltimateDell MediaDirect™ 4.0KeyboardNumber of keys 86 (U.S. and Canada); 102 (Europe); 105 (Japan); 104 (Brazil)Layout QWERTY/AZERTY/Kanji NOTE: Backlit keyboard is optionalCamera (optional)Pixel 2.0 mega pixelVideo Resolution 320x240 ~1600x1200 (640x480 at 30fps)Diagonal Viewing Angle 66°Touch PadX/Y position resolution (graphics table mode) 240 cpiSize:Width73.09-mm (2.87-in) sensor-active area Height40.09-mm (1.57-in) rectangle
30 SpecificationsBatteryType 9-cell "smart" lithium ion 6-cell "smart" lithium ion4-cell "smart" lithium ionDimensions:Depth48.3 mm (1.9 in) (4/6/9 cell)Height20.4 mm (0.8 in) (4/6 cell)37.8 mm (1.5 in) (9 cell)Width206.6 mm (8.13 in) (4/6 cell)284.9 mm (11.2 in) (9 cell)Weight 0.24 kg (0.54 lb) (4 cell)0.34 kg (0.75 lb) (6 cell) 0.5 kg (1.1 lb) (9 cell)Voltage 11.1 VDC (6/9 cell)14.8 VDC (4 cell)Charge time (approximate):Computer off4 hoursOperating time Battery operating time varies depending on operating conditions and can be significantly reduced under certain power-intensive conditions. See Dell Technology Guide for more information on battery life.Life span (approximate) 300 discharge/charge cyclesTemperature range:Operating0° to 35°C (32° to 95°F)Storage–40° to 65°C (–40° to 149°F)Coin-cell battery CR-2032
Specifications 31AC AdapterInput voltage 100–240 VACInput current (maximum) 1.5 AInput frequency 50–60 HzOutput current65 W90 W3.34 A (continuous)4.34 A (peak for 4-second pulse)4.62 A (continuous)5.62 A (peak for 4-second pulse)Output power 65 W or 90 WRated output voltage 19.5 VDCDimensions:65 WHeight28.2 mm (1.11 in) Width57.9 mm (2.28 in) Length137.2 mm (5.4 in) 90 WHeight34.2 mm (1.35 in)Width60.9 mm (2.39 in)Length153.42 mm (6.04 in)Weight (without cables)65 W0.29 kg (0.64 lb)90 W0.345 kg (0.76 lb)Temperature range:Operating0° to 35°C (32° to 95°F) Storage–40° to 65°C (–40° to 149°F)Connector types:DC connector3 pin, 7.4 mm plugAC connector2 pin - C7 (Japan only)3 pin - C5
32 SpecificationsPhysicalHeight 25.3 mm to 38.5 mm (1.0 in to 1.51 in) Width 355 mm (13.98 in)Depth 261.9 mm (10.31 in)Weight (with 4-cell battery):Configurable to less than2.68 kg (5.91 lb)EnvironmentalTemperature range:Operating0° to 35°C (32° to 95°F)Storage–40° to 65°C (–40° to 149°F)Relative humidity (maximum):Operating10% to 90% (noncondensing)Storage5% to 95% (noncondensing)Maximum vibration (using a random vibration spectrum that simulates user environment):Operating0.66 GRMSStorage1.3 GRMSMaximum shock (Measured with hard drive in operating but not accessing data status and a 2-ms half-sine pulse for operating. Also measured with hard drive in head-parked position and a 2-ms halfsine pulse for storage):Operating110 GStorage160 GAltitude (maximum):Operating–15.2 to 3048 m (–50 to 10,000 ft)Storage–15.2 to 10,668 m (–50 to 35,000 ft)Airborne containment level G2 or lower as defined by ISA-S71.04-1985
Troubleshooting 33TroubleshootingDell Technical Update ServiceThe Dell Technical Update service provides proactive e-mail notification of software and hardware updates for your computer. This service is free and can be customized for content, format, and frequency of notifications.To enroll for the Dell Technical Update service, go to support.dell.com/technicalupdate.Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.Diagnostics AvailableDepending on which Dell computer you have purchased there may be additional extended Dell 32 Bit Diagnostics available on the hard drive in a Utility Partition that provides additional troubleshooting.When to Use PSA Diagnostics and Dell 32 Bit DiagnosticsIf you experience a problem with your computer, perform the checks in "Lockups and Software Problems" on page 44 and run PSA Diagnostics and Dell 32 Bit Diagnostics before you contact Dell for technical assistance.It is recommended that you print these procedures before you begin. NOTE: PSA and 32 Bit Dell Diagnostics operate only on Dell computers.Enter system setup, review your computer’s configuration information, and ensure that the device you want to test displays in system setup and is active (for more information on system setup, see Dell Technology Guide).Start the Dell 32 Bit Diagnostics from your hard drive or from your Drivers and Utilities media.
34 TroubleshootingStarting PSA Diagnostics From Your Computer NOTE: If your computer does not display a screen image, contact Dell (see "Contacting Dell" on page 58). NOTE: Troubleshooting using Dell 32 Bit Diagnostics through the Utility Partition, referenced in this section, may or may not be available in your computer.1Ensure that the computer is connected to an electrical outlet.2Turn on (or restart) your computer.3Start PSA Diagnostics in one of the following two ways:aWhen the DELL™ logo appears, press <F12> immediately. Select Diagnostics from the boot menu, and then press <Enter>. NOTE: If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop, then shut down your computer and try again. NOTE: Before attempting option B, the computer must be turned off.bPress and hold the <Fn> key while powering the computer on.Follow the prompts on the screen, select Diagnostics to start the PSA suite of tests. The computer then runs the Pre-boot Self Assessment, a series of initial tests of your system board, keyboard, hard drive, and display.• During the assessment, provide inputs when prompted.• If a failure is detected, the computer stops and beeps. To stop the assessment and restart the computer, press <n>; to continue to the next test, press <y>; to retest the component that failed, press <r>. • If failures are detected during the Pre-boot System Assessment, write down the error code(s) and contact Dell.If the Pre-boot System Assessment completes successfully and your system has 32 Bit Diagnostics, you receive the message Booting Dell Diagnostics Utility Partition. Press any key to continue.4Press any key to start the Dell 32 Bit Diagnostics.
Troubleshooting 35Starting the Dell 32 Bit Diagnostics From the Drivers and Utilities Media NOTE: Depending on which Dell computer you have purchased there may not be an additional extended Dell 32 Bit Diagnostics available on the Drivers and Utilities media referenced in this section.1Insert your Drivers and Utilities media.2Shut down and restart the computer.3When the DELL logo appears, press <F12> immediately. NOTICE: Keyboard failure may result when a key on the keyboard is held down for extended periods of time. To avoid possible keyboard failure, press and release <F12> in even intervals until the boot device menu appears.4At the boot device menu, use the up- and down-arrow keys to highlight CD/DVD/CD-RW, and then press <Enter>. NOTE: The Quickboot feature changes the boot sequence for the current boot only. Upon restart, the computer boots according to the boot sequence specified in system setup.5Select the Boot from CD-ROM option from the menu that appears, and then press <Enter>.6Ty p e 1 to start the Drivers and Utilities menu, and then press <Enter>.7Select Run the 32 Bit Dell Diagnostics from the numbered list. If multiple versions are listed, select the version appropriate for your computer.8At the Dell Diagnostics Main Menu, select the test you want to run. NOTE: Write down the error codes and problem descriptions exactly as they appear and follow the instructions on the screen.9After all tests have completed, close the test window to return to the Dell Diagnostics Main Menu.10Remove your Drivers and Utilities media and close the Main Menu window to exit Diagnostics. Restart the computer.
36 TroubleshootingDell Diagnostics Main MenuAfter the Dell Diagnostics loads and the Main Menu screen appears, click the button for the option you want. NOTE: It is recommended that you select Test System to run a complete test on your computer.After you have selected the Test System option from the main menu, the following menu appears. NOTE: It is recommended that you select Extended Test from the menu below to run a more thorough check of the devices in the computer.For any problem encountered during a test, a message appears with an error code and a description of the problem. Write down the error code and problem description exactly as it appears and follow the instructions on the screen. If you cannot resolve the problem, contact Dell (see "Contacting Dell" on page 58). NOTE: The Service Tag for your computer is located at the top of each test screen. When contacting Dell support, have your Service Tag ready.Option FunctionTest Memory Run the stand-alone memory testTest System Run System DiagnosticsExit Exit DiagnosticsOption FunctionExpress Test Performs a quick test of system devices. The test typically takes 10 to 20 minutes and requires no interaction on your part. Run Express Test first to increase the possibility of tracing the problem quickly.Extended Test Performs a thorough check of system devices. The test typically takes an hour or more and periodically requires your input to answer specific questions.Custom Test Tests a specific device in the system and can be used to customize the tests you want to run.Symptom Tree Lists a number of common symptoms and allows you to select a test based on the symptom of the problem you are having.
Troubleshooting 37The following tabs provide additional information for tests run from the Custom Test or Symptom Tree option:Dell Support CenterThe Dell Support Center helps you find the service, support and system-specific information you need. For more information about Dell Support Center and available support tools, click the Services tab at support.dell.com. Click on the icon in the taskbar to run the application. The home page provides links to access:• Self Help (Troubleshooting, Security, System Performance, Network/Internet, Backup/Recovery, and Windows Vista)• Alerts (technical support alerts relevant to your computer)• Assistance from Dell (Technical Support with DellConnect™, Customer Service, Training and Tutorials, How-To Help with Dell on Call, and Online Scan with PCCheckUp)• About Your System (System Documentation, Warranty Information, System Information, Upgrades & Accessories)The top of the Dell Support Center home page displays your system’s model number along with its service tag and express service code. Tab FunctionResults Displays the results of the test and any error conditions encountered.Errors Displays error conditions encountered, error codes, and the problem description.Help Describes the test and any requirements for running the test.Configuration Displays your hardware configuration for the selected device.The Dell Diagnostics obtains configuration information for all devices from system setup, memory, and various internal tests, and it displays the information in the device list in the left pane of the screen. The device list may not display the names of all the components installed on your computer or all devices attached to your computer.Parameters Allows you to customize the test by changing the test settings.
38 TroubleshootingFor more information on Dell Support Center, see the Dell Technology Guide. It is available in Windows Help and Support (Start → Help and Support) and at Dell Support Website.Drive Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.Fill out the "Diagnostics Checklist" on page 57 as you complete these checks.ENSURE THAT MICROSOFT® WINDOWS® RECOGNIZES THE DRIVE —• Click Start → Computer.If the drive is not listed, perform a full scan with your antivirus software to check for and remove viruses. Viruses can sometimes prevent Windows from recognizing the drive.TEST THE DRIVE —• Insert another CD, DVD, or BD to eliminate the possibility that the original media is defective.• Insert a bootable media and restart the computer.CLEAN THE DRIVE OR DISK —See Dell Technology Guide.CHECK THE CABLE CONNECTIONSCHECK FOR HARDWARE INCOMPATIBILITIES —See Dell Technology Guide for instructions on troubleshooting software and hardware problems.RUN THE DELL DIAGNOSTICS —See "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33.Hard drive problemsALLOW THE COMPUTER TO COOL BEFORE TURNING IT ON —A hot hard drive may prevent the operating system from starting. Try allowing the computer to return to room temperature before turning it on.RUN CHECK DISK —1Click Start → Computer.2Right-click Local Disk (C:).
Troubleshooting 393Click Properties→ Tools→ Check Now. NOTE: The User Account Control window may appear. If you are an administrator on the computer, click Continue; otherwise, contact your administrator to continue the desired action.4Click to check Scan for and attempt recovery of bad sectors, and then click Start.Error MessagesFill out the "Diagnostics Checklist" on page 57 as you complete these checks. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.If the message is not listed, see the documentation for the operating system or the program that was running when the message appeared.AUXILIARY DEVICE FAILURE —The touch pad or external mouse may be faulty. For an external mouse, check the cable connection. If the problem persists, contact Dell (see "Contacting Dell" on page 58).BAD COMMAND OR FILE NAME —Ensure that you have spelled the command correctly, put spaces in the proper place, and used the correct pathname.CACHE DISABLED DUE TO FAILURE —The primary cache internal to the microprocessor has failed. Contact Dell (see "Contacting Dell" on page 58).CD DRIVE CONTROLLER FAILURE —The CD drive does not respond to commands from the computer (see "Drive Problems" on page 38).DATA ERROR —The hard drive cannot read the data (see "Drive Problems" on page 38).DECREASING AVAILABLE MEMORY —One or more memory modules may be faulty or improperly seated. Reinstall the memory modules and, if necessary, replace them (see Service Manual for instructions to replace memory modules).DISK C: FAILED INITIALIZATION —The hard drive failed initialization. Run the hard drive tests in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33). DRIVE NOT READY —The operation requires a hard drive in the bay before it can continue. Install a hard drive in the hard drive bay.
40 TroubleshootingEXTENDED MEMORY SIZE HAS CHANGED —The amount of memory recorded in NVRAM does not match the memory installed in the computer. Restart the computer. If the error appears again, contact Dell.THE FILE BEING COPIED IS TOO LARGE FOR THE DESTINATION DRIVE —The file that you are trying to copy is too large to fit on the disk, or the disk is full. Try copying the file to a different disk or use a larger capacity disk.A FILENAME CANNOT CONTAIN ANY OF THE FOLLOWING CHARACTERS: \ / : * ? “ < > | — Do not use these characters in filenames.GATE A20 FAILURE —A memory module may be loose. Reinstall the memory modules and, if necessary, replace them. GENERAL FAILURE —The operating system is unable to carry out the command. The message is usually followed by specific information—for example, Printer out of paper. Take the appropriate action.HARD-DISK DRIVE CONFIGURATION ERROR —The computer cannot identify the drive type. Shut down the computer, remove the hard drive, and boot the computer from a CD. Then, shut down the computer, reinstall the hard drive, and restart the computer. Run the Hard Disk Drive tests in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).HARD-DISK DRIVE CONTROLLER FAILURE 0—The hard drive does not respond to commands from the computer. Shut down the computer, remove the hard drive, and boot the computer from a CD. Then, shut down the computer, reinstall the hard drive, and restart the computer. If the problem persists, try another drive. Run the Hard Disk Drive tests in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).HARD-DISK DRIVE FAILURE —The hard drive does not respond to commands from the computer. Shut down the computer, remove the hard drive, and boot the computer from a CD. Then, shut down the computer, reinstall the hard drive, and restart the computer. If the problem persists, try another drive. Run the Hard Disk Drive tests in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).
Troubleshooting 41HARD-DISK DRIVE READ FAILURE —The hard drive may be defective. Shut down the computer, remove the hard drive, and boot the computer from a CD. Then, shut down the computer, reinstall the hard drive, and restart the computer. If the problem persists, try another drive. Run the Hard Disk Drive tests in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).INSERT BOOTABLE MEDIA —The operating system is trying to boot to nonbootable media, such as a CD. Insert bootable media.INVALID CONFIGURATION INFORMATION-PLEASE RUN SYSTEM SETUP PROGRAM —The system configuration information does not match the hardware configuration. The message is most likely to occur after a memory module is installed. Correct the appropriate options in the system setup program.KEYBOARD CLOCK LINE FAILURE —For external keyboards, check the cable connection. Run the Keyboard Controller test in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).KEYBOARD CONTROLLER FAILURE —For external keyboards, check the cable connection. Restart the computer, and avoid touching the keyboard or the mouse during the boot routine. Run the Keyboard Controller test in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).KEYBOARD DATA LINE FAILURE —For external keyboards, check the cable connection. Run the Keyboard Controller test in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).KEYBOARD STUCK KEY FAILURE —For external keyboards or keypads, check the cable connection. Restart the computer, and avoid touching the keyboard or keys during the boot routine. Run the Stuck Key test in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).LICENSED CONTENT IS NOT ACCESSIBLE IN MEDIADIRECT —Dell MediaDirect™ cannot verify the Digital Rights Management (DRM) restrictions on the file, so the file cannot be played.MEMORY ADDRESS LINE FAILURE AT ADDRESS, READ VALUE EXPECTING VALUE —A memory module may be faulty or improperly seated. Reinstall the memory modules and, if necessary, replace them.
42 TroubleshootingMEMORY ALLOCATION ERROR —The software you are attempting to run is conflicting with the operating system, another program, or a utility. Shut down the computer, wait 30 seconds, and then restart it. Try to run the program again. If the error message still appears, see the software documentation.MEMORY DATA LINE FAILURE AT ADDRESS, READ VALUE EXPECTING VALUE —A memory module may be faulty or improperly seated. Reinstall the memory modules and, if necessary, replace them.MEMORY DOUBLE WORD LOGIC FAILURE AT ADDRESS, READ VALUE EXPECTING VALUE —A memory module may be faulty or improperly seated. Reinstall the memory modules and, if necessary, replace them.MEMORY ODD/EVEN LOGIC FAILURE AT ADDRESS, READ VALUE EXPECTING VALUE —A memory module may be faulty or improperly seated. Reinstall the memory modules and, if necessary, replace them.MEMORY WRITE/READ FAILURE AT ADDRESS, READ VALUE EXPECTING VALUE —A memory module may be faulty or improperly seated. Reinstall the memory modules and, if necessary, replace them.NO BOOT DEVICE AVAILABLE —The computer cannot find the hard drive. If the hard drive is your boot device, ensure that the drive is installed, properly seated, and partitioned as a boot device.NO BOOT SECTOR ON HARD DRIVE —The operating system may be corrupted. Contact Dell (see "Contacting Dell" on page 58).NO TIMER TICK INTERRUPT —A chip on the system board may be malfunctioning. Run the System Set tests in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33). NOT ENOUGH MEMORY OR RESOURCES. EXIT SOME PROGRAMS AND TRY AGAIN —You have too many programs open. Close all windows and open the program that you want to use.OPERATING SYSTEM NOT FOUND —Reinstall the hard drive. If the problem persists, contact Dell (see "Contacting Dell" on page 58). OPTIONAL ROM BAD CHECKSUM —The optional ROM has failed. Contact Dell (see "Contacting Dell" on page 58).A REQUIRED .DLL FILE WAS NOT FOUND —The program that you are trying to open is missing an essential file. Remove and then reinstall the program.
Troubleshooting 431Click Start → Control Panel.2Under Programs, click Uninstall a Program.3Select the program you want to remove.4Click Uninstall and follow the prompts on the screen.5See the program documentation for installation instructions.SECTOR NOT FOUND —The operating system cannot locate a sector on the hard drive. You may have a defective sector or corrupted FAT on the hard drive. Run the Windows error-checking utility to check the file structure on the hard drive. See Windows Help and Support for instructions (click Start → Help and Support). If a large number of sectors are defective, back up the data (if possible), and then reformat the hard drive.SEEK ERROR —The operating system cannot find a specific track on the hard drive. SHUTDOWN FAILURE —A chip on the system board may be malfunctioning. Run the System Set tests in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).TIME-OF-DAY CLOCK LOST POWER —System configuration settings are corrupted. Connect your computer to an electrical outlet to charge the battery. If the problem persists, try to restore the data by entering the system setup program, then immediately exit the program. If the message reappears, contact Dell (see "Contacting Dell" on page 58).TIME-OF-DAY CLOCK STOPPED —The reserve battery that supports the system configuration settings may require recharging. Connect your computer to an electrical outlet to charge the battery. If the problem persists, contact Dell (see "Contacting Dell" on page 58).TIME-OF-DAY NOT SET-PLEASE RUN THE SYS T E M SETUP PROGRAM —The time or date stored in the system setup program does not match the system clock. Correct the settings for the Date and Time options.TIMER CHIP COUNTER 2 FAILED —A chip on the system board may be malfunctioning. Run the System Set tests in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).UNEXPECTED INTERRUPT IN PROTECTED MODE —The keyboard controller may be malfunctioning, or a memory module may be loose. Run the System Memory tests and the Keyboard Controller test in the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).
44 TroubleshootingX:\ IS NOT ACCESSIBLE. THE DEVICE IS NOT READY —Insert a disk into the drive and try again.WARNING: BATTERY IS CRITICALLY LOW —The battery is running out of charge. Replace the battery, or connect the computer to an electrical outlet; otherwise, activate hibernate mode or shut down the computer.Lockups and Software Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.The computer does not startCHECK THE AC ADAPTER —Ensure that the AC adapter is firmly connected to the computer and to the electrical outlet.The computer stops responding NOTICE: You might lose data if you are unable to perform an operating system shutdown.TURN THE COMPUTER OFF —If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds until the computer turns off, then restart your computer. A program stops responding or crashes repeatedlyEND THE PROGRAM —1Press <Crtl><Shift><Esc> simultaneously.2Click the Applications tab and select the program that is no longer responding.3Click End Task. NOTE: The chkdsk program may run when you restart the computer. Follow the instructions on the screen. CHECK THE SOFTWARE DOCUMENTATION —If necessary, uninstall and then reinstall the program. Software usually includes installation instructions in its documentation or on a DVD.
Troubleshooting 45A program is designed for an earlier Microsoft® Windows® operating systemRUN THE PROGRAM COMPATIBILITY WIZARD —Program compatibility is a mode in Windows that lets you run programs written for earlier versions of Windows. For more information, search for the keyword program compatibility wizard in Windows Help and Support.A solid blue screen appearsTURN THE COMPUTER OFF —If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds until the computer turns off, then restart your computer. Memory ProblemsFill out the "Diagnostics Checklist" on page 57 as you complete these checks. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.IF YOU RECEIVE AN INSUFFICIENT MEMORY MESSAGE —• Save and close any open files and exit any open programs you are not using to see if that resolves the problem.• See the software documentation for minimum memory requirements. If necessary, install additional memory.• Reseat the memory modules to ensure that your computer is successfully communicating with the memory.• Run the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33). IF YOU EXPERIENCE OTHER MEMORY PROBLEMS —• Reseat the memory modules to ensure that your computer is successfully communicating with the memory.• Ensure that you are following the memory installation guidelines.• Run the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).
46 TroubleshootingPower ProblemsFill out the "Diagnostics Checklist" on page 57 as you complete these checks. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer.CHECK THE POWER LIGHT —When the power light is lit or blinking, the computer has power. If the power light is blinking, the computer is in Sleep state—press the power button to exit Sleep state. If the light is off, press the power button to turn on the computer.CHARGE THE BATTERY —The battery charge may be depleted.1Reinstall the battery.2Use the AC adapter to connect the computer to an electrical outlet.3Turn on the computer. NOTE: Battery operating time (the time the battery can hold a charge) decreases over time. Depending on how often the battery is used and the conditions under which it is used, you may need to purchase a new battery during the life of your computer.CHECK THE BATTERY STATUS LIGHT —If the battery status light flashes amber or is a steady amber, the battery charge is low or depleted. Connect the computer to an electrical outlet.If the battery status light flashes blue and amber, the battery is too hot to charge. Shut down the computer, disconnect the computer from the electrical outlet, and then let the battery and computer cool to room temperature.If the battery status light rapidly flashes amber, the battery may be defective. Contact Dell (see "Contacting Dell" on page 58).CHECK THE BATTERY TEMPERATURE —If the battery temperature is below 0°C (32°F), the computer will not start.TEST THE ELECTRICAL OUTLET —Ensure that the electrical outlet is working by testing it with another device, such as a lamp.CHECK THE AC ADAPTER —Check the AC adapter cable connections. If the AC adapter has a light, ensure that the light is on.CONNECT THE COMPUTER DIRECTLY TO AN ELECTRICAL OUTLET —Bypass power protection devices, power strips, and extension cables to verify that the computer turns on.
Troubleshooting 47ELIMINATE POSSIBLE INTERFERENCE —Turn off nearby fans, fluorescent lights, halogen lamps, or other appliances.ADJUST THE POWER PROPERTIES —See Dell Technology Guide for power management settings.RESEAT THE MEMORY MODULES —If the computer power light turns on, but the display remains blank, reinstall the memory modules.Troubleshooting Software and Hardware Problems in the Windows Vista® Operating SystemIf a device is either not detected during the operating system setup or is detected but incorrectly configured, use Windows Vista Help and Support to resolve the incompatibility. Windows Vista is a new operating system, so many older devices may not have drivers or applications for Windows Vista. Check with your hardware manufacturer for further information on their device.To start the Hardware Troubleshooter:1Click Start → Help and Support.2In the Find an answer section, click Troubleshooting.ORTy p e hardware troubleshooter in the search field, then press <Enter>.3In the search results, select the option that best describes the problem and follow the troubleshooting steps. NOTE: If you do not find the answer in the items categorized in Troubleshooting, you can get Online Help by typing in your question in the Search Help field at the top of the window.
48 TroubleshootingRestoring Your Operating SystemYou can restore your operating system in the following ways:• Windows Vista® has the Backup and Restore Center that can create backups of important files on your computer, or backup the entire computer. You may then restore your operating system or files if needed.• Microsoft Windows Vista System Restore returns your computer to an earlier operating state without affecting data files. Use System Restore as the first solution for restoring your operating system and preserving data files. For instructions, see "Using Windows Vista System Restore" on page 48.• If you received an Operating System media with your computer, you can use it to restore your operating system. However, using the Operating System media also deletes all data on the hard drive. Use the media only if System Restore did not resolve your operating system problem.Using Windows Vista System RestoreThe Windows Vista operating system provides System Restore to allow you to return your computer to an earlier operating state (without affecting data files) if changes to the hardware, software, or other system settings have left the computer in an undesirable operating state. See the Windows Help and Support Center for information on using System Restore. To access the Windows Help and Support Center, click Start → Help and Support. NOTICE: Make regular backups of your data files. System Restore does not monitor your data files or recover them. NOTE: The procedures in this document were written for the Windows default view, so they may not apply if you set your Dell computer to the Windows Classic view.Creating a Restore PointYou can automatically and manually create a restore point from the Windows Vista Back Up and Restore Center. There are two ways to get to the Windows Vista Backup and Restore Center:1Click Start → Welcome Center. In the Get started with Windows section, click Show all 14 items...→ Back Up and Restore Center. 2Click Start → All Programs → Maintenance → Back Up and Restore Center. Under Tas k s, click Create a restore point or change settings.
Troubleshooting 49For more information,1Click Start → Help and Support.2Ty p e System Restore in the search field and press <Enter>.Restoring the Computer to an Earlier Operating StateIf problems occur after you install a device driver, use Device Driver Rollback to resolve the problem. If that is unsuccessful, then use System Restore. NOTICE: Before you restore the computer to an earlier operating state, save and close all open files and exit any open programs. Do not alter, open, or delete any files or programs until the system restoration is complete.1Click Start → Control Panel→ System and Maintenance→ Back Up and Restore Center.2In the Tasks list, click Repair Windows using System Restore. 3Click Continue in the User Account Control (UAC) dialog box asking for permission to run the application.4Click Next in the System Restore window to view the most recent restore points in chronological order.5Select the Show restore points older than 5 days checkbox to view the complete list of restore points. 6Select a restore point. Try to restore from the most recent restore point. If this fails to correct the problem, try the next oldest restore point until the issue is resolved. Any software installed after the selected restore point will need to be reinstalled.7Click Next→ Finish.8When prompted, click Yes.9After System Restore finishes collecting data, the computer restarts.10After the computer restarts, click OK. To change the restore point, you can either repeat the steps using a different restore point, or you can undo the restoration.If you encounter any error messages during the restore process, follow the prompts on the screen to correct the error.
50 TroubleshootingUndoing the Last System Restore NOTICE: Before you undo the last system restore, save and close all open files and exit any open programs. Do not alter, open, or delete any files or programs until the system restoration is complete.1Click Start → Help and Support.2Ty p e System Restore in the search field and press <Enter>.3Click Undo my last restoration, and then click Next.Restoring the Computer to the Default Factory ConfigurationThe Dell Factory Image Restore option allows you to restore your hard drive back to its original factory configuration as when you first ordered it from Dell. This option appears on Dell computers that were originally pre-installed with Windows Vista® and does not include computers purchased through the Express Upgrade promotion or computers that were upgraded to Windows Vista from another version of Windows. NOTICE: When you restore the computer to the default factory configuration, all data on the C drive is deleted. Before performing this procedure, back up personal files. If you do not back up personal files, the data is lost.1Restart the computer. To do this, click Start → → Restart.2As the computer restarts, press <F8> until the Advanced Boot Options menu appears on the screen. NOTE: You must press the <F8> key before the Windows logo appears on the screen. If you press <F8> after the Windows logo appears on the screen, the Advanced Boot Options menu will not appear on the screen. If you do not see the Advanced Boot Options menu, restart the computer, and then repeat this step until you see the menu on the screen.3Press <Down Arrow> to select Repair Your Computer on the Advanced Boot Options menu, and then press <Enter>.4Specify the language settings that you want, and then click Next. 5Log in as a user who has administrative credentials, and then click OK.
Troubleshooting 516Click Dell Factory Image Restore.7In the Dell Factory Image Restore window, click Next. 8Select the Yes, reformat hard drive and restore system software to factory condition checkbox.9Click Next. The computer is restored to the default factory configuration.10When the restore operation is completed, click Finish to restart the computer.
52 Troubleshooting
Getting Help 53Getting HelpObtaining Assistance CAUTION: If you need to remove the computer cover, first disconnect the computer power and modem cables from all electrical outlets.If you experience a problem with your computer, you can complete the following steps to diagnose and troubleshoot the problem:1See "Troubleshooting" on page 33 for information and procedures that pertain to the problem your computer is experiencing.2See "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33 for procedures on how to run Dell Diagnostics.3Fill out the "Diagnostics Checklist" on page 57.4Use Dell's extensive suite of online services available at Dell Support (support.dell.com) for help with installation and troubleshooting procedures. See "Online Services" on page 54 for a more extensive list of Dell Support online.5If the preceding steps have not resolved the problem, see "Contacting Dell" on page 58. NOTE: Call Dell Support from a telephone near or at the computer so that the support staff can assist you with any necessary procedures. NOTE: Dell's Express Service Code system may not be available in all countries.When prompted by Dell's automated telephone system, enter your Express Service Code to route the call directly to the proper support personnel.For instructions on using the Dell Support, see "Technical Support and Customer Service" on page 54. NOTE: Some of the following services are not always available in all locations outside the continental U.S. Call your local Dell representative for information on availability.
54 Getting HelpTechnical Support and Customer ServiceDell's support service is available to answer your questions about Dell™ hardware. Our support staff uses computer-based diagnostics to provide fast, accurate answers.To contact Dell's support service, see "Before You Call" on page 56, and then see the contact information for your region or go to support.dell.com.DellConnectDellConnect is a simple online access tool that allows a Dell service and support associate to access your computer through a broadband connection, diagnose your problem and repair it all under your supervision. You can access DellConnect from the Dell Support Center (see "Dell Support Center" on page 37).Online ServicesYou can learn about Dell products and services on the following websites:www.dell.comwww.dell.com/ap (Asian/Pacific countries only)www.dell.com/jp (Japan only)www.euro.dell.com (Europe only)www.dell.com/la (Latin American and Caribbean countries)www.dell.ca (Canada only)You can access Dell Support through the following websites and e-mail addresses:• Dell Support websitessupport.dell.comsupport.jp.dell.com (Japan only)support.euro.dell.com (Europe only)• Dell Support e-mail addressesmobile_support@us.dell.comsupport@us.dell.com la-techsupport@dell.com (Latin America and Caribbean countries only)apsupport@dell.com (Asian/Pacific countries only)
Getting Help 55• Dell Marketing and Sales e-mail addressesapmarketing@dell.com (Asian/Pacific countries only)sales_canada@dell.com (Canada only)• Anonymous file transfer protocol (FTP)ftp.dell.comLog in as user: anonymous, and use your e-mail address as your password.AutoTech ServiceDell's automated support service—AutoTech—provides recorded answers to the questions most frequently asked by Dell customers about their portable and desktop computers.When you call AutoTech, use your touch-tone telephone to select the subjects that correspond to your questions. For the telephone number to call for your region, see "Contacting Dell" on page 58.Automated Order-Status ServiceTo check on the status of any Dell products that you have ordered, you can go to support.dell.com, or you can call the automated order-status service. A recording prompts you for the information needed to locate and report on your order. For the telephone number to call for your region, see "Contacting Dell" on page 58.Problems With Your OrderIf you have a problem with your order, such as missing parts, wrong parts, or incorrect billing, contact Dell for customer assistance. Have your invoice or packing slip handy when you call. For the telephone number to call for your region, see "Contacting Dell" on page 58.Product InformationIf you need information about additional products available from Dell, or if you would like to place an order, visit the Dell website at www.dell.com. For the telephone number to call for your region or to speak to a sales specialist, see the "Contacting Dell" on page 58.
56 Getting HelpReturning Items for Warranty Repair or CreditPrepare all items being returned, whether for repair or credit, as follows:1Call Dell to obtain a Return Material Authorization Number, and write it clearly and prominently on the outside of the box.For the telephone number to call for your region, see "Contacting Dell" on page 58.2Include a copy of the invoice and a letter describing the reason for the return.3Include a copy of the Diagnostics Checklist (see "Diagnostics Checklist" on page 57), indicating the tests that you have run and any error messages reported by the Dell Diagnostics (see "Pre-Boot Self Assessment (PSA) Diagnostics and Dell 32 Bit Diagnostics" on page 33).4Include any accessories that belong with the item(s) being returned (power cables, software floppy disks, guides, and so on) if the return is for credit.5Pack the equipment to be returned in the original (or equivalent) packing materials.You are responsible for paying shipping expenses. You are also responsible for insuring any product returned, and you assume the risk of loss during shipment to Dell. Collect On Delivery (C.O.D.) packages are not accepted.Returns that are missing any of the preceding requirements will be refused at Dell’s receiving dock and returned to you.Before You Call NOTE: Have your Express Service Code ready when you call. The code helps Dell’s automated-support telephone system direct your call more efficiently. You may also be asked for your Service Tag (located on the back or bottom of your computer).Remember to fill out the Diagnostics Checklist (see "Diagnostics Checklist" on page 57). If possible, turn on your computer before you call Dell for assistance and call from a telephone at or near the computer. You may be asked to type some commands at the keyboard, relay detailed information during operations, or try other troubleshooting steps possible only at the computer itself. Ensure that the computer documentation is available. CAUTION: Before working inside your computer, follow the safety instructions that shipped with your computer.
Getting Help 57Diagnostics ChecklistName:Date:Address:Phone number:Service Tag (bar code on the back or bottom of the computer):Express Service Code:Return Material Authorization Number (if provided by Dell support technician):Operating system and version:Devices:Expansion cards:Are you connected to a network? Yes NoNetwork, version, and network adapter:Programs and versions:See your operating system documentation to determine the contents of the system’s start-up files. If the computer is connected to a printer, print each file. Otherwise, record the contents of each file before calling Dell.Error message, beep code, or diagnostic code:Description of problem and troubleshooting procedures you performed:
58 Getting HelpContacting DellFor customers in the United States, call 800-WWW-DELL (800-999-3355). NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, Contacting Dell techsheet, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues:1Visit support.dell.com.2Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page. 3Click Contact Us on the left side of the page.4Select the appropriate service or support link based on your need.5Choose the method of contacting Dell that is convenient for you.
Appendix 59AppendixFCC Notice (U.S. Only)FCC Class BThis equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. NOTICE: The FCC regulations provide that changes or modifications not expressly approved by Dell Inc. could void your authority to operate this equipment. These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures: • Reorient the receiving antenna.• Relocate the system with respect to the receiver.• Move the system away from the receiver.• Plug the system into a different outlet so that the system and the receiver are on different branch circuits. If necessary, consult a representative of Dell Inc. or an experienced radio/television technician for additional suggestions.
60 AppendixThe following information is provided on the device or devices covered in this document in compliance with the FCC regulations: Macrovision Product NoticeThis product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.Product name: Dell™ Studio™ 1535/1536Model number: PP33LCompany name: Dell Inc.Worldwide Regulatory Compliance & Environmental AffairsOne Dell WayRound Rock, TX 78682 USA512-338-4400
Index 61IndexBbatteryremoving, 20Bluetooth wireless technology carddevice status light, 11Ccamera, 10Check Disk, 38computercrashes, 44-45restore to previous operating state, 48-49specifications, 23stops responding, 44DDell Diagnosticsabout, 33starting from the Drivers and Utilities media, 35starting from your hard drive, 34DellConnect, 54device latch releasedescription, 19device status lightsdescription, 11diagnosticsDell, 33digital array microphones, 14displaydescription, 10Drivers and Utilities CDDell Diagnostics, 33drivesproblems, 38Eerror messages, 39Hhard driveproblems, 38hardwareDell Diagnostics, 33Hardware Troubleshooter, 47
62 IndexIIEEE 1394 connectordescription, 16Mmedia control buttonsdescription, 10messageserror, 39modem connectordescription, 19Nnetwork connectordescription, 16Ooperating systemreinstalling Windows Vista, 48-50Ppowerproblems, 46power buttondescription, 11power lightconditions, 46problemsblue screen, 45computer crashes, 44-45computer does not start up, 44computer stops responding, 44Dell Diagnostics, 33drives, 38error messages, 39hard drive, 38lockups, 44power, 46power light conditions, 46program crashes repeatedly, 44program stops responding, 44programs and Windows compatibility, 45restore computer to previous operating state, 48-49restore operating system to previous state, 48software, 44-45RreinstallingWindows Vista, 48-50Ssecurity cable slotdescription, 18softwareproblems, 45
Index 63software and hardware incompatibilities, 47specifications, 23System Restore, 48-49Ttouch pad buttonsdescription, 14track stick/touch pad buttonsdescription, 14troubleshootingDell Diagnostics, 33Hardware Troubleshooter, 47restore computer to previous operating state, 48-49WWindows VistaProgram Compatibility wizard, 45reinstalling, 48-50System Restore, 48-49wizardsProgram Compatibility wizard, 45
64 Index

Navigation menu