Bosch Security Systems TTMW Wireless Tri-Tech Motion Dectector User Manual F01U284862 01a ISW ZDL1 WP11G Inguide indd

Bosch Security Systems, Inc. Wireless Tri-Tech Motion Dectector F01U284862 01a ISW ZDL1 WP11G Inguide indd

Manual

© 2013 Bosch Security Systems, Inc. F.01U.284.862 | 02 | 2013.09 | 1===121312GreenVertYellowJauneRedRougeen Installation and Operation GuideTriTech motion detectorISW-ZDL1-WP11G13251 mm(2.0 in)131 mm(5.2 in)67 mm(2.6 in)46x 1.5 VDuracell MN1500 AA Alkaline Panasonic AM-3PIX AA Alkaline 0°C to +49°C (+32°F to +120°F)2.2 - 2.7 m(7.5 - 9 ft)Pet friendlyAnimaux acceptés 1 ≤ 45 kg (100 lbs) 2 ≤ 27 kg (60 lbs) ≤ 1052 sec+AA+AA+AA+AAAA+AA+AA90 sec811 12 80 sec 10 sec13 14 15<3 min0 - 93% Non-Condensing humidity65 sec7Refer to the instruction manual that came with the control panel to complete the pairing process.Reportez-vous aux instructions fournies avec le panneau de commande pour terminer le processus d’appariementOptional mounting brackets / Support de montage en option: B328, B335, B338 15 sec10992 sec
© 2013 Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, NY 14450 F.01U.284.862 | 02 | 2013.09 | 2Bosch Security Systems, Inc. product manufacturing datesUse the serial number located on the product label and refer to the Bosch Security Systems, Inc website at: http://www.boschsecurity.com/datecodes/.CopyrightThis document is the intellectual property of Bosch Security Systems, Inc. and is protected by copyright. All rights reserved.TrademarksAll hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.FCCThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer-ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installa-tion. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for helpICThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.AAAAAA AAAA+AA+AAAAAAAA AAAA12 3AAAAAA AAAAAA<4 sec<3 min1 21AAAAAA AAAA+AA2+AA+AA+AA+AAAA+AA+AA3Normal OperationFonctionnement NormalLow Battery / Trouble ConditionBatterie faible /Condition de troubleResetRéinitialiser 5191

Navigation menu