Bosch Security Systems EVOLVE50 Self-powered column speaker system User Manual EVOLVE 50 Installation Manual

Bosch Security Systems Inc Self-powered column speaker system EVOLVE 50 Installation Manual

Users Manual

EVOLVE 50 Portable Column System en | Installation manual
Table of contents1Safety 41.1 Important safety instructions 41.2 FCC information 51.3 Precautions 71.4 Notices 72Short information 82.1 Shipping contents 83Description 93.1 System features 93.2 Quick setup 104Installation 115Amplifier DSP 125.1 Amplifier DSP controls 125.2 System status 135.3 DSP control menu 146Pairing the QuickSmart Mobile application 207Recommended configurations 217.1 Stereo pair of EVOLVE 50 systems 217.2 Solo musician performance 228Troubleshooting 239Technical data 259.1 Dimensions 269.2 Frequency response 26 en 3Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
SafetyImportant safety instructionsWARNING: TO REDUCE THE RISK OFFIRE OR ELECTRIC SHOCK, DO NOTOVEREXPOSE THIS APPLIANCE TO RAINOR MOISTUREAVIS: RISQUE DE CHOC ELECTRIQUE,NE PAS OUVRIR.WARNING: THE MAINS PLUG OR ACINLET IS USED AS A DISCONNECTDEVICE. THE DISCONNECT DEVICESHALL REMAIN READILY OPERABLE.WARNING: CONNECT ONLY TO MAINSSOCKET WITH PROTECTIVE EARTHINGCONNECTION.WARNING: TO REDUCE THE RISK OFELECTRIC SHOCK, DO NOT REMOVECOVER (OR BACK) AS THERE ARE NOUSER-SERVICABLE PARTS INSIDE.REFER SERVICING TO QUALIFIEDPERSONNEL.The lightning flash with arrowheadsymbol, within an equilateral triangle isintended to alert the user to thepresence of uninsulated “dangerousvoltage” within the product’s enclosurethat may be sufficient magnitude toconstitute a risk of electric shock topersons.!The exclamation point within anequilateral triangle is intended to alertthe user to the presence of importantoperating and maintenance (servicing)instructions in the literatureaccompanying the appliance.The asterisk within an equilateraltriangle is intended to inform the user tonecessary installation or removalinstructions regarding equipment orhardware use relating to the system. 1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with a dry cloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer'sinstructions.8. Do not install near any heat sources such as radiators, heat registers, stoves, or otherapparatus (including amplifiers) that produce heat.9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plughas two blades with one wider than the other. A grounding type plug has two blades anda third grounding prong. The wide blade or the third prong is provided for your safety. Ifthe provided plug does not fit into your outlet, consult an electrician for replacement ofthe obsolete outlet.10. Protect the power cord from being walked on or pinched particularly at plugs,convenience receptacles, and the point where they exit from the apparatus.11. Only use attachments/accessories specified by the manufacturer.12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, orwith the apparatus. When a cart is used, use caution when moving the cart/apparatuscombination to avoid injury from tip-over.13. Unplug the apparatus during lightning storms or when unused for long periods of time.11.1EVOLVE 50 Portable Column System 2017.07 | 02 | F.01U.341.640 Installation manual Electro-Voice
14. Refer all servicing to qualified service personnel. Servicing is required when theapparatus has been damaged in any way, such as power-supply cord or plug is damaged,liquid has been spilled or objects have fallen into the apparatus, the apparatus has beenexposed to rain or moisture, does not operate normally, or has been dropped.15. No naked flame sources, such as lighted candles, should be placed on the apparatus.16. To reduce the risk of fire or electric shock, do not expose this apparatus to rain ormoisture. The apparatus should not be exposed to dripping or splashing. Objects filledwith liquids, such as vases should not be placed on apparatus.17. Do not block any ventilation openings. Install in accordance with the manufacturer'sinstructions.18. Minimum 60 cm (2 ft) distances around the apparatus for sufficient ventilation.19. The ventilation should not be impeded by covering the ventilation openings with items,such as newspapers, table-cloths, curtains, etc.20. To completely disconnect AC power from this apparatus, the power supply cord must beunplugged. !Warning!This product is not designed to be suspended. Do NOT use handles or any other method tosuspend the loudspeaker. Handles on Electro-Voice loudspeakers are intended to only beused for temporary transport by people.Items, such as fiber rope, wire rope, cables, or other types of materials cannot be used tosuspend loudspeaker from the handles.!Caution!Do not attempt to move this loudspeaker system when it is fully assembled.You may damage the system or cause personal injury.FCC informationThis device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may causeundesired operation.1.2 en 5Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
Notice!This product has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation. This product generates,uses, and can radiate radio frequency energy and, if not installed and used in accordance withthe instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. Ifthis product does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.—Consult the dealer or an experienced radio/TV technician for help. The device contains a BT module CYBLE-022001-00 which has been granted by FCC and IC,the FCC ID:WAP2001 and IC:7922A-2001. And module is assembled on the PRE PCB Please take attention that changes or modification not expressly approved by the partyresponsible for compliance could void the user’s authority to operate the equipment.This equipment should be installed and operated with a minimum distance 20cm between theradiator and your body This device complies with Industry Canada license-exempt RSS standard(s). Operation issubject to the following two conditions:(1) this device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesiredoperation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareilsradioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si lebrouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antennaof a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. Toreduce potential radio interference to other users, the antenna type and its gain should be sochosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than thatnecessary for successful communication.Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peutfonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pourl'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillageradioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gainde sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensiténécessaire à l'établissement d'une communication satisfaisante. EVOLVE 50 Portable Column System 2017.07 | 02 | F.01U.341.640 Installation manual Electro-Voice
Precautions!If an Electro-Voice loudspeaker is used outdoors on a sunny day, place theloudspeaker in a shaded or covered area. The loudspeaker amplifiers haveprotection circuits that temporarily shut the loudspeaker off when extremelyhigh temperatures are reached. This can happen on hot days when theloudspeaker is in direct sunlight.!Do not use Electro-Voice loudspeakers in an environment where temperaturesare below 0°C (32°F) or exceed +35°C (95°F).!Never expose an Electro-Voice loudspeaker to rain, water, or high moisture.!Electro-Voice loudspeakers are easily capable of generating sound pressurelevels sufficient to cause permanent hearing damage to anyone within normalcoverage distance. Caution should be taken to avoid prolonged exposure tosound pressure levels exceeding 90 dB.NoticesOld electrical and electronic appliancesElectrical or electronic devices that are no longer serviceable must be collected separately andsent for environmentally compatible recycling (in accordance with the European WasteElectrical and Electronic Equipment Directive).To dispose of old electrical or electronic devices, you should use the return and collectionsystems put in place in the country concerned.Copyright and disclaimerAll rights reserved. No part of this document may be reproduced or transmitted in any form byany means, electronic, mechanical, photocopying, recording, or otherwise, without the priorwritten permission of the publisher. For information on getting permission for reprints andexcerpts, contact Electro-Voice.The content and illustrations are subject to change without prior notice.Notice!Bluetooth® is available in select countries.Contact your nearest Electro-Voice dealer or Electro-Voice distributor for more information.The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.and any use of such marks by Bosch Security Systems, Inc. is under license. Other trademarksand trade names are those of their respective owners.1.31.4 en 7Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
Short informationThe following table lists products in a family, with CTN (Commercial Type Number) andidentifying product name DESCRIPTION.CTN DescriptionEVOLVE50-TB Column speaker array, pole, blackEVOLVE50-SB-US Column speaker sub US, blackEVOLVE50-SB-EU Column speaker sub EU, blackEVOLVE50-SB-AP Column speaker sub AP, blackEVOLVE50-SB-GL Column speaker sub, black, global, no BTShipping contents Quantity Component1 Subwoofer1 Power cord1 EVOLVE 50 installation manual1 Warranty card1 Safety manualTable 2.1: Subwoofer boxQuantity Component1 Column array1 Sub pole1 Carry bagTable 2.2: Column array box22.1EVOLVE 50 Portable Column System 2017.07 | 02 | F.01U.341.640 Installation manual Electro-Voice
DescriptionThank you for choosing an Electro-Voice portable column system. Please take time to consultthe manual to understand all the features built into your EV system and fully utilize itsperformance capabilities. The EVOLVE 50 portable column system is a new entry and form factor in the Electro-Voiceportable sound portfolio. Designed to deliver an uncompromising combination of low-profileaesthetics and superior audio performance, the EVOLVE 50 sets a new standard for portablecolumnar systems. EVOLVE 50 is designed to quickly and easily be transported and assembled. The three handledesign on the subwoofer and convenient included carry case for the sub pole and columnarray provide minimal resistance to getting excellent, professional sound anywhere you needit. Installation is made easier via the symmetrical aluminum subwoofer pole with an integratedwire assembly. The connection is secured by the magnetic assisted latching system, whichmagnetically locks the sub pole in place. The full-range column array and its eight 3.5-inch neodymium drivers are directed usingcustom-designed waveguides for consistent 120° coverage. The ported subwoofer enclosurehouses a 12-inch woofer that is supported by 18 mm wood for enhanced stiffness andacoustical performance. The Class-D amplifier provides up to 1000 watts of output power: 500watts to the subwoofer and 500 watts to the column array. The input panel features EV'sindustry-leading QuickSmartDSP interface—allowing intuitive navigation of system parametersvia an LCD with single-knob control—as well as multiple options for signal routing and inputs. The new Electro-Voice QuickSmart Mobile application utilizes Bluetooth® Low Energy (BTLE)technology for the wireless configuration, control, and monitoring of up to six EVOLVE 50systems simultaneously. High-resolution Bluetooth® audio streaming adds convenience forwireless music playback in breakout rooms, intermission, and musical accompaniment.Bluetooth® is available in select countries. Electro-Voice quality and testing procedures far exceed the industry norm to yield efficientand effective electro-acoustic performance; this creates components that deliver an accurate,linear response at the system’s highest output levels. When applied to EVOLVE 50, thisengineering philosophy results in a system that brings a new sonic benchmark to the columnspeaker segment, all packaged in a sleek and portable enclosure that blends into thebackground in any application from a lounge to a wedding reception.System features▪EV QuickSmart Mobile application: quickly and wirelessly configure, control, and monitorup to six EVOLVE 50 systems simultaneously, and receive immediate notification duringcritical performance conditions. Bluetooth® connectivity is available in select countries.▪High-quality Bluetooth® audio streaming for background music or musicalaccompaniment. Bluetooth® connectivity is available in select countries.▪Ultra-wide 120° horizontal coverage via custom-designed waveguides and array-formed40° asymmetrical vertical coverage means all acoustical energy is directed towards bothsitting and standing audiences.33.1 en 9Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
▪QuickSmartDSP provides best-in-class processing via EV's signature single-knob userinterface with LCD. Easy setup via four presets (Music, Live, Speech, Club), three-bandEQ (low, mid, high), five user-programmable presets (Store and Recall settings), outputdelay, phantom power, visual monitoring of limiter status, input level control and meters,and master volume control to optimize gain structure.▪Ideal for portable applications. Light weight and intuitive assembly via the magnetassisted sub pole make a quality performance easier than ever.Quick setupSubwooferTo set up a subwoofer, do the following:Step Illustration1. Connect the AC power cord from agrounded line receptacle to the MAINS IN.FUS E T5AL/25 0VREPLACE AS MARKEDOPE RATING V OLTAGE / TEGAN GAN:100-240V AC / 50-60 HzMAINS IN2. Connect the XLR or TRS cables from anaudio source to INPUT 1 or INPUT 2 orconnect the RCA cable or 3.5 mm mini jackfrom an audio source to INPUT 3.3. Adjust the input gain to (infinity).4. Switch POWER to ON.POWERON OF F5. From the DSP home screen, increase theinput gain to the desired sound output.6. Adjust the MASTER VOL knob to thedesired volume.See also•Amplifier DSP, page 123.2EVOLVE 50 Portable Column System 2017.07 | 02 | F.01U.341.640 Installation manual Electro-Voice
Installation!Caution!Do not attempt to move this loudspeaker system when it is fully assembled.You may damage the system or cause personal injury.Assembling the loudspeaker systemTo assemble the loudspeaker system, do the following:1. Place the subwoofer on a level and stable surface.2. Insert the symmetrical pole into the top of the subwoofer.The pole has magnets (A) at each end. The pole can be inserted on either end.AA3. Place the column array loudspeaker on top of the subwoofer pole.4. The column array loudspeaker system set up is complete.4 en 11Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
Amplifier DSPAmplifier DSP controlsThe amplifier has a combination of controls and connectors to ensure the most versatileloudspeaker system.Portable column system control and monitoring interfaceThe portable column system DSP control menu selections are available for the EVOLVE 50 .1 2 435 98761. LCD – DSP control and monitoring interface.2. MASTER VOL – Adjusts the sound level.DSP – Scroll through the menu and select the available choices. Push the MASTER VOLknob to enter the DSP menu.3. LINE | MIC – Electronically balanced INPUT 1 and INPUT 2 MIC/LINE for the connection ofa line level signal source (such as mixer etc.) or a microphone. Phantom power (+15 V)can be enabled Phantom 1 or 2 if a condenser microphone is being used. Establishing aconnection is possible via TRS or XLR-type plugs. Whenever possible, balanced signalfeed is always preferable to guard against potential noise or HF-interference. This controllets you optimally adjust the incoming signals to match the sensitivity of the system.4. AUX IN – Control to adjust the input trim of the stereo RCA type, 3.5mm, or Bluetooth®streaming inputs. This control lets you optimally adjust the incoming signals to match thesensitivity of the system. Bluetooth®connectivity is available in select countries.5. MIX OUT – The post-fader audio signals of INPUT 1, INPUT 2 and INPUT 3 are mixed andpassed to MIX OUT. The ratio of the input signals changes when the level controls INPUT1, 2 or 3 are adjusted. This feature allows the loudspeaker to act as a basic three-channelmixer that can send the mix to another loudspeaker via the MIX OUT socket. This outputis laid out in GND-SENSING technology, a special pin assignment of the output socket,offering all advantages of the balanced signal transmission, but lets you also connectmonaural plugs without a problem.6. THRU – The THRU output socket is connected in parallel to INPUT 1, it is used for carryingthrough the pre-fader input signal to additional powered loudspeaker or subwoofer.7. INPUT – Electronically balanced INPUT 1/2 MIC/LINE for the connection of a line levelsignal source (such as mixer etc.) or a microphone. Establishing a connection is possiblevia TRS or XLR-type plugs. Whenever possible, balanced signal feed is always preferableto guard against potential noise or HF-interference.8. INPUT 3 RCA Connector – Stereo unbalanced RCA type INPUT 3 AUX IN for connectingsources such as CD players or MP3 players.55.1EVOLVE 50 Portable Column System 2017.07 | 02 | F.01U.341.640 Installation manual Electro-Voice
9. INPUT 3 3.5mm connector – Balanced mono or unbalanced stereo input for mobilephones, laptops, etc.EVOLVE 50FUSE T5AL/250VREPLACE AS M ARKEDOPERATING VO LTAGE / TEGANGAN:100-240V AC / 50-60 HzMAINS I NPOWERON OFFBOSCH SICHERHEITSSYSTEME G MBH85626 GRASBRUNN, GE RMANYBOSCH SECURITY SYSTEMS, INC14450 FAIRPORT, NY, USA FOR INDONESIA ONLY:IMPORTED BY / DIIMPOR OLEHPT ROBERT BOSCHJAKARTA, INDONESIAwww.electrovoice.com | MADE IN CHINA10 11Notice!Markings and statements on amplifier panel may vary.10. MAINS IN – The device receives its power supply via the MAINS IN socket. Only theprovided power cord may be used. Connect the device only to a mains network, whichcorresponds to the requirements indicated on the type plate.11. POWER – AC switch for switching the power ON or OFF. The LCD screen lights up whenthe power is turned ON, after approximately 3 seconds.System statusNormalIN1IN2LEVEL 0dB C1IN312345678SEFigure 5.1: Normal system status home screen with Bluetooth® status1. LEVEL – Indicates the master gain of the system in dB. The range is from mute to +10 dB,in 1 dB increments.2. IN1 – VU meter displays the signal level of INPUT 1 into the amplifier INPUT 1 XLRconnector. IN1 and IN2 are independent of each other.3. IN2 – VU meter displays the signal level of INPUT 2 into the amplifier INPUT 2 XLRconnector. IN1 and IN2 are independent of each other.4. IN3 – VU meter displays the signal level of INPUT 3.5. C - Control app; the available options are:OFF - DISABLEDFLASHING - PAIRING MODESOLID - CONNECTED6. 1 - Indicates the selected store function number. There are five user defined storefunction numbers available.7. E - Indicates the preset is not saved. When the preset is saved the E is not displayed.8. S - Audio streaming; the available options are: 5.2 en 13Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
OFF - DISABLEDFLASHING - PAIRING MODE (120s)SOLID - CONNECTEDNotice!Bluetooth® is available in select countries.Contact your nearest Electro-Voice dealer or Electro-Voice distributor for more information.System protectionSystem protection limiters indicate when a system is exceeding recommended usage byindicating CLIP or LIMIT on the LCD display.CLIPCLIP indicates the signal to the loudspeaker is too high, resulting in a clipped signal into theloudspeaker. If CLIP is shown, reduce the input gain knob and/or the signal on the mixer orsource equipment.LIMITLIMIT protects the loudspeaker from short-term peaks which can cause distortion. WhenLIMIT is shown small on the screen, the limiter is active but keeps distortion under control.The large LIMIT indicates the sound is negatively affected. Reducing the output volume(MASTER VOL) is strongly recommended when the large limit indication is shown.See also•Pairing the QuickSmart Mobile application, page 20DSP control menuEXITMODE MUSIC (Default)LIVESPEECHCLUBSUB LEVEL 0 dB (Default)Mute, +1 dB to +10 dBTREBLE 0 dB (Default)-12 dB to +6 dBMID 0 dB (Default)-12 dB to +6 dBMID FREQ 1200 Hz (Default)200 to 12000 HzBASS 0 dB (Default)-12 dB to +6 dBPHANTOM 1 ONOFF (Default) 5.3EVOLVE 50 Portable Column System 2017.07 | 02 | F.01U.341.640 Installation manual Electro-Voice
PHANTOM 2 ONOFF (Default)MIX OUT L+R (Default)RDELAY FEET OFF (Default)OFF, 0.1 to 100.0 m (and ft.)METERLED OFFON (Default)LIMITCONTROL APPDISPLAY BACK LCD DIM ON (Default)OFFBRIGHT 5 (Default)1 to 10CONTRAST 5 (Default)1 to 10BACK STORE EXIT, 1, 2, 3, 4, 5, EXITRECALL EXIT, 1, 2, 3, 4, 5, EXITBLUETOOTH CONTROLAPPONOFF (Default)STREAMING PAIRINGONOFF (Default)RESET RESET ARE YOU SURE?NO (Default)YESINFO [PRODUCT NAME][FIRMWARE VERSION]©2017 Electro-VoiceEXITTable 5.1: Portable column system DSP Control Menu en 15Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
EXIT MenuThe Exit menu is used to return to the home screen.Notice!The display returns to the home screen after two minutes of inactivity.MODE MenuThe Mode menu is used to configure the type of sound the subwoofer delivers.▪MUSIC – is used for recorded music playback and electronic dance music applications.(Default)▪LIVE – is used for live sound applications.▪SPEECH – is used for spoken word applications.▪CLUB – is used for recorded electronic music playback.SUB LEVEL MenuThe Sub Level menu allows independent gain control of the subwoofer output. Changes tothis parameter effectively change the crossover of the EVOLVE 50 system. The default settingof 0 dB is recommended for best audio performance.The range is MUTE, +1 dB to +10 dB.The default is 0 dB.TREBLE MenuThe Treble menu is used to adjust the high frequency performance of the loudspeaker fordifferent applications or personal preference. The parameter controls a high shelving filterthat is centered on 6 kHz.The range is -12 dB to +6 dB.The default is 0 dB.MID MenuThe MID menu is used to set the gain of the MID peak filter.The range is -12 dB to +6 dB.The default is 0 dB.MID FREQ MenuThe MID Freq menu is used to set the center frequency of the MID peak filter.The range is 200 -12000 Hz.The default is 1200 Hz.BASS MenuThe Bass menu item is used to configure the low frequencies of sound.The range is -12 dB to +6 dB.The default is 0 dB.PHANTOM 1 or PHANTOM 2 MenuThe Phantom 1 or Phantom 2 menu is for activating phantom power (+15 V) of audio INPUT 1or 2 whenever a suitable condenser microphone is being used. Available options for thisselection are: ON or OFF.The default is OFF.MIX OUT MenuThe Mix Out menu is used to select which signal of INPUT 3 AUX IN should be output at MIXOUT and which signal should be delivered by the loudspeaker.▪L+R: The left and right signals of INPUT 3 are summed. The sum is output at MIX OUT andis delivered by the loudspeaker. (Default)▪R: Only the right signal of INPUT 3 is output at MIX OUT. The loudspeaker will deliver onlythe left signal. EVOLVE 50 Portable Column System 2017.07 | 02 | F.01U.341.640 Installation manual Electro-Voice
DELAY MenuThe Delay menu is used to delay the output signal, e.g. to compensate for differences indistance among individual loudspeakers. The delay can be set in meters or feet. Availableoptions for this selection are: OFF or a delay up to 100.0 m or 328 ft. The delay can bechanged in 0.25 meter increments or one foot increments.The default is OFF.DISPLAY MenuThe Display menu options are BACK, LCD DIM, BRIGHT, and CONTRAST.LED MenuThe LED menu shows power on and indicates limit. Available options for this selection are:ON, OFF, LIMIT or CONTROL APP.▪ON – turns the LED on when the power to the loudspeaker is ON. (Default)▪OFF – turns the LED off.▪LIMIT – turns the LED off under normal operation. The LED brief blinking indicates thelimiter is activating. Short-term blinking is not critical because the integrated limiterkeeps distortion under control. Constant lighting of the LED indicates the sound isnegatively affected. If the LED is constantly lit, check the rear LCD for more information.Reducing the output volume is strongly recommended.▪CONTROL APP – indicates if Bluetooth® on the portable column system is trying to pairor is connected to a Bluetooth® enabled mobile device. In pairing mode the LED will flashblue indicating it is ready to pair. The LED is solid blue when it is connected.The default is ON.LCD DIM MenuThe LCD Dim menu is used to dim the display when the display is idle for two minutes.Available options for this selection are: ON or OFF.The default is ON.BRIGHT MenuThe Bright menu is used to determine the brightness of the LCD.The range is 1 to 10.The default is five (5).CONTRAST MenuThe Contrast menu is used to increase or decrease the visibility of the LCD screen.The range is 1 to 10.The default is five (5).STORE MenuThe Store menu allows you create up to five customized user settings. Available options forthis selection are: EXIT, 1, 2, 3, 4, and 5.Notice!The customized user setting name can contain a combination of alphanumeric charactersincluding spaces. The alphanumeric character range is A to Z and 0-9.The name field length is 12 characters.Storing customized user settingsTo store customized user settings, do the following:1. From the DSP menu, scroll to STORE.2. Push the MASTER VOL knob to select STORE.The store screen appears.3. Push the MASTER VOL knob to select 1.The Enter name for 1 screen appears. en 17Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
4. Use the MASTER VOL knob to scroll through the characters.The characters appear.5. Push the MASTER VOL knob to select the desired character.6. Turn the MASTER VOL knob to move to the next character entry.Continue selecting characters until the desired name is entered.7. Use the MASTER VOL knob to scroll to SAVE.8. Push the MASTER VOL knob to select SAVE.9. Repeat steps 3 through 8 to store additional customized user settings.10. Select EXIT to return to the home screen.RECALL MenuThe Recall menu allows you retrieve up to five customized user settings. Available options forthis selection are: EXIT, 1, 2, 3, 4, and 5.Recalling customized user settingsTo recall customized user settings, do the following:1. From the DSP menu, scroll to RECALL.2. Push the MASTER VOL knob to select RECALL.The recall screen appears.3. Push the MASTER VOL knob to select 1.The selected item is loaded.4. Select EXIT to return to the home screen.BLUETOOTHThe Bluetooth menu options are CONTROL APP and STREAMING.CONTROL APP MenuThe Control App menu is used to enable the QuickSmart Mobile wireless control andmonitoring application. Available options for this selection are: ON or OFF.The default is OFF.Notice!Bluetooth® is available in select countries.Contact your nearest Electro-Voice dealer or Electro-Voice distributor for more information.The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.and any use of such marks by Bosch Security Systems, Inc. is under license. Other trademarksand trade names are those of their respective owners.Turning Bluetooth® ON or OFFTo turn Bluetooth® ON or OFF, do the following:1. From the DSP menu, scroll to CONTROL APP.2. Select ON.ORSelect OFF.STREAMINGThe Streaming menu is used to stream audio from your Bluetooth® enabled device via theloudspeaker system. Available options for this selection are: PAIRING, ON or OFF.The default is OFF.Pairing the portable column system with your Bluetooth® enabled deviceTo pair the portable column system with your Bluetooth® enabled device, do the following:1. From the DSP menu, scroll to STREAMING.2. Select PAIRING.PAIRING mode enables 120 seconds of visibility to Bluetooth® enabled devices. EVOLVE 50 Portable Column System 2017.07 | 02 | F.01U.341.640 Installation manual Electro-Voice
3. On your mobile device, select EV EVOLVE to initiate the pairing process.Once the device is paired, all device audio will be output through the EVOLVE 50 system.Notice!If connected with a mobile device, notification alerts and ring tones will also be playedthrough the system.Disable these notifications or enable Airplane mode on your mobile device to preventunwanted interruptions during audio playback.Turning streaming ON or OFFTo turn streaming ON or OFF, do the following:1. From the DSP menu, scroll to STREAMING.2. Select ON.ORSelect OFF.RESET MenuThe Reset menu is used to reset the loudspeaker to original factory settings. Available optionsfor this selection are: NO or YES.The default is NO.Resetting the systemTo reset the system to original factory settings, do the following:1. From the DSP menu, select RESET. The reset "Are you sure?" message appears.2. Select YES. The system is reset to the original factory settings.Notice!The reset menu item is used to revert the loudspeaker to the original factory default settings.All user settings will be deleted. The user customized settings in the STORE and RECALLmenus return to <EMPTY>.INFO MenuThe Information menu is used to display the product name and firmware version.See also•Pairing the QuickSmart Mobile application, page 20 en 19Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
Pairing the QuickSmart Mobile applicationThe EV QuickSmart Mobile app is available for download for the iOS 10 and higher tablets andsmart phones from the iTunes App Store or Android Marshmallow and higher tablets andsmart phones from the Google Play Store.Notice!The EV QuickSmart Mobile app is designed to only find speakers from Electro-Voice withBluetooth® enabled.The EV QuickSmart Mobile app will not display other types of Bluetooth® devices, e.g.phones, laptops, tablets, or headsets.Notice!Bluetooth® is available in select countries.Contact your nearest Electro-Voice dealer or Electro-Voice distributor for more information.Prior to pairing the EV QuickSmart Mobile app with loudspeakers by Electro-Voice ensureBluetooth® is enabled on the smart phone or tablet, and the loudspeaker.First time pairing:To pair the loudspeaker with the EV QuickSmart Mobile app, do the following:1. Open the EV QuickSmart Mobile app. 2. Finding nearby speakers is displayed on the screenThe EV QuickSmart Mobile app is looking for available Bluetooth® enabled Electro-Voiceloudspeakers.3. The available loudspeakers are displayed on the screen.The app will display up to eight available loudspeakers.4. Tap the loudspeaker you want to pair with the app.The selected loudspeaker will have a red line under it acknowledging it is selected.5. Repeat the previous step until all of the desired loudspeakers are selected.6. Tap the red CONNECT button.7. The app pairs with the desired loudspeaker. The app can connect to up to six loudspeakers. Subsequent pairing:To pair the loudspeaker with the EV QuickSmart Mobile app, do the following:1. Tap the EV QuickSmart Mobile app icon. 2. Finding nearby speakers is displayed on the screenThe EV QuickSmart Mobile app is looking for available Bluetooth® enabled Electro-Voiceloudspeakers.3. The available loudspeakers are displayed on the screen.The app will display up to eight available loudspeakers.4. Tap the loudspeaker you want to pair with the app.The selected loudspeaker will have a red line under it acknowledging it is selected.5. Repeat the previous step until all of the desired loudspeakers are selected.6. Tap the red CONNECT button.7. The app pairs with the desired loudspeaker. The app can connect to up to six loudspeakers.6 EVOLVE 50 Portable Column System 2017.07 | 02 | F.01U.341.640 Installation manual Electro-Voice
Recommended configurationsStereo pair of EVOLVE 50 systemsLRR RightL LeftNotice!The direction of the arrow indicates the signal path.Mode: MusicMIX-OUT: RTable 7.1: DSP settings for the portable column systemSee also•DSP control menu, page 14 77.1 en 21Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
Solo musician performanceBAA Guitar, conga drum, etc.B Condenser microphoneNotice!The direction of the arrow indicates the signal path.Mode: LivePhantom 1: OnTable 7.2: DSP settings for the portable column systemSee also•DSP control menu, page 147.2 EVOLVE 50 Portable Column System 2017.07 | 02 | F.01U.341.640 Installation manual Electro-Voice
Troubleshooting Problem Possible cause Action1. No sound Amplifier Verify all the electronics are on, the signalrouting is correct, the source is active; thevolume is turned up, etc. Correct/repair/replace as necessary. If there isstill no sound, the problem may be wiring.Wiring Verify you have connected the correct cables tothe amplifier. Play something at a low levelthrough the amplifier. Connect a testloudspeaker in parallel with the malfunctioningline. If the sound level is gone or is very weak,the line has a short in it (possibly a severescrape, pinch, or a missed connection). Usingthe test loudspeaker, move down the line andtest each connection/junction until you find theproblem and correct it. Observe properpolarity.2. Intermittentoutput such ascrackling ordistortionFaulty connection Check all connections at amplifier andloudspeakers to ensure they are all clean andtight. If the problem persists, check the wiring.See problem 1.3. Constant noisesuch asbuzzing hissingor hummingDefective source orother electronicdeviceIf noise is present, but no program material isplaying, evaluate each component as necessaryto isolate the problem. Most likely there is abreak in the signal path.Poor systemgrounding or groundloopCheck and correct the system grounding, asrequired.Input gain knob is notin the MIC positionSlowly increase the input gain knob level toengage the microphone pre-amp.4. No soundproduced withmicrophoneconnected toINPUT 1 orINPUT 2Microphone requiresphantom power.Use a dynamic microphone that does notrequire phantom power (+15 V). If using amicrophone requiring phantom power, enablePHANTOM POWER is the DSP menu, or use anexternal phantom power source.Input gain knob is notin the MIC positionSlowly increase the input gain knob level toengage the microphone pre-amp.5. Sound isdistorted frontLED is OFF,LCD screenLIMIT is ONExcessive input level Reduce the input level or loudspeaker levelknobs to prevent limit.8 en 23Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
Problem Possible cause ActionIncorrect gainstructure or sourceinput (mixing console/preamp) is overdrivenVerify level controls of the source are properlystructured by using the VU meter indicator onthe LCD screen. If the VU meter bar is solid orthe system indicates LIMIT, the input or sourcelevel is too high.6. Microphoneproducesacousticfeedback wheninput level isamplifiedIncorrect gainstructureReduce the microphone levels at the mixingconsole or input source. If the microphone isconnected directly to the speaker, reduce theinput level on the speaker. Positioning themicrophone close to the sound sourceincreases gain-before-feedback. See problem 6.MODE is set to MUSIC Change the MODE to LIVE or SPEECH.Microphone positionis too close to thefront of theloudspeakerWhenever possible setup the loudspeakers sothe microphone is behind them. If using theloudspeaker in a monitor position, aim theloudspeaker to the back of the microphone.7. DSP menu islockedThe Menu Lockfunction has beenturned on.Press and hold the MASTER VOL knob for 5seconds.8. QuickSmartMobile appdoes notdetect theloudspeakerEnable Bluetooth® Ensure Bluetooth® is enabled on theloudspeaker.If these suggestions do not solve your problem, contact your nearest Electro-Voice dealer orElectro-Voice distributor.EVOLVE 50 Portable Column System 2017.07 | 02 | F.01U.341.640 Installation manual Electro-Voice
Technical dataFrequency Response (-3 dB): 43 Hz – 20 KHz1Frequency Range (-10 dB): 37 Hz – 20 KHz1Maximum SPL: 127 dB2Coverage (H x V): 120° x 40°Amplifier Rating: 1000 WLF Channel Rating: 500 WHF Channel Rating: 500 WCrossover Frequency: 200 HzConnectors: 2x XLR/TRS Combo Jack Input1x 3.5 mm Input 1x Stereo RCA Input1x Wireless Bluetooth® Audio Input1x XLR THRU Output1x XLR MIX OUT OutputEnclosure: Sub: 15 mm plywoodColumn: CompositePole: AluminumGrille: Steel with black powder coatColor: BlackDimensions (HxWxD):mm (in)Sub: 530 x 345 x 471 (20.9 x 13.6 x 18.5)Column: 825 x 102 x 172 (32.5 x 4.0 x 6.9)Pole: 929 x 48.5 x 55 (36.6 x 1.9 x 2.2)Net Weight: Sub: 44.66 lb (20.3 kg)Column: 10.34 lb (4.7 kg)Pole: 2.75 lb (1.25 kg)Sub cover: 0.9 lb (0.4 kg)Bag for column and pole:1.87 (0.85 kg)Shipping Weight: Sub box: 50.71 lb (23 kg) Column box: 18.30 lb (8.3 kg)Power Consumption: 100 - 240 V AC, 50 - 60 Hz, 1.5 - 0.6 A31Full space measurement using music DSP preset.2Maximum SPL is measured at 1 m using broadband pink noise at maximum output.3Current rating is 1/8 power.9 en 25Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
Dimensions345 mm530.0 mm470 mm492 mm7 mm930 mm55 mm48.5 mm38.5 mm789 mm68 mm37.9 mm29.7 mm102 mm825 mm121.2 mm102.4 mm102 mm157.2 mm121.2 mm172.0 mm108.7 mm[13.6 in][6.8 in][6.2 in][4.8 in][4.0 in][32.5 in][4.0 in] [4.3 in][4.0 in][4.8 in][31.1 in][36.6 in][2.7 in][1.5 in][1.2 in][2.2 in][1.9 in][1.5 in][0.3 in][19.4 in][20.9 in][18.5 in]471 mm[18.5 in]Figure 9.1: Dimensions EVOLVE 50 (subwoofer left, spacer center, and column right) Frequency responseFigure 9.2: Frequency response EVOLVE 50 (Live Mode, Music Mode, Speech mode, and Club Mode)9.1 9.2EVOLVE 50 Portable Column System 2017.07 | 02 | F.01U.341.640 Installation manual Electro-Voice
en 27Electro-Voice Installation manual 2017.07 | 02 | F.01U.341.640
Bosch Sicherheitssysteme GmbHRobert-Bosch-Ring 585630 GrasbrunnGermanywww.boschsecurity.com© Bosch Sicherheitssysteme GmbH, 2017Bosch Security Systems, Inc12000 Portland Avenue SouthBurnsville MN 55337USAwww.electrovoice.com

Navigation menu