Bioness Neuromodulation A Bioness L3P-T-RFS-V20 L300 Plus Thigh RF Stimulation Unit User Manual part 5

Bioness Neuromodulation ltd. A Bioness Inc Company L300 Plus Thigh RF Stimulation Unit part 5

user manual part 5

100 User's GuideBasesReplace the L300 electrode bases if they appear worn or damaged.To replace the L300 electrode bases:1. Mark the position of the used L300 electrode bases on the L300 FS Cuff liner. See Figure 9-6.Figure 9-6: Marking the position of the used L300 electrode bases.Figure 9-7: Unsnapping the L300 electrode bases.2. Unsnap the L300 electrode bases from the plug holes. See Figure 9-7.
101Chapter 9 - Maintenance and CleaningFigure 9-8: Removing the used L300 electrode bases.Figure 9-9. Attaching the new L300 electrode bases.3. Remove the used L300 electrode bases from the L300 FS Cuff. See Figure 9-8.4. Attach the new L300 electrode bases where the previous bases were attached. See Figure 9-9.
102 User's GuideFigure 9-10: Snapping the L300 electrode bases to the L300 FS Cuff plug holes.Figure 9-11: Wire concealers covering the L300 electrode base wires.CAUTION: When replacing the L300 FS Cuff, have your clinician re-fit the L300 electrode bases.5. Snap the new L300 electrode bases to the L300 FS Cuff plug holes. See Figure 9-10. 6. Cover the wires and snaps with wire concealers (not included), if desired. See Figure 9-11. Press on the wire concealers to attach them to the L300 FS Cuff liner.Wire Concealer
103Chapter 9 - Maintenance and CleaningL300 FS Cuff StrapTo replace the L300 FS Cuff strap:1. Remove the used L300 FS Cuff strap from the L300 FS Cuff buckles and strap leads. See Figure 9-12.Strap BucklesStrap LeadsHook and Loop FastenersFigure 9-12: L300 FS Cuff strap attached to the L300 FS Cuff.2. Slide the new L300 FS Cuff strap through the strap leads and buckles. Make sure the hook and loop fasteners face away from the L300 FS Cuff.3. Press on the hook and loop fasteners to secure the strap.
104 User's GuideThigh Silicone PanelsTo replace the Thigh silicone panels:1. Unsnap and remove the Thigh cloth electrodes.2. Gently detach the loops of the silicone panels from the hooks on the Thigh FS Cuff top and bottom panels. See Figure 9-13. Figure 9-13: Unhooking the top silicone panel.
105Chapter 9 - Maintenance and Cleaning3. Slide the band on the bottom silicone panel over the Thigh RF Stim Unit. See Figure 9-14.Figure 9-14: Sliding the band on the bottom silicone panel.Figure 9-15: Pulling the silicone panels away from the electrode snaps.4. Gently pull the silicone panels away from the cloth electrode snaps. See Figure 9-15.
106 User's Guide5. Gently slide the new silicone panels around the electrode snaps.6. Slide the band on the bottom silicone panel over the Thigh RF Stim Unit. See Figure 9-16.Figure 9-16: Sliding the band on the bottom silicone panel over the RF Stim Unit.7. Gently hook the new silicone panels to the Thigh FS Cuff. See Figure 9-17.Figure 9-17: Hooking the new silicone panel to the Thigh FS Cuff.
107Chapter 9 - Maintenance and CleaningRemoving the L300 and Thigh RF Stim UnitsThe L300 and Thigh RF Stim Units should only be removed for maintenance and to clean the FS Cuffs.To remove the RF Stim Units:1. Turn off the L300 Plus System.2. Pull the top of the RF Stim Unit away from the cradle. See Figure 9-18. Figure 9-18: Removing the RF Stim Units.Note: If the fit is too tight, open the flexible cover over the RF Stim Unit charging port for a better grasp.3. Remove the bottom of the RF Stim Unit from the cradle.To re-insert the RF Stim Unit:1. Insert the bottom of the RF Stim Unit into the cradle. Then, gently push the top of the RF Stim Unit until it snaps into the cradle.Cradle Cradle
108 User's GuideCleaning the L300 Plus ComponentsAll L300 Plus components may be cleaned by carefully wiping them with a damp cloth. The electrical components are not waterproof. Do not immerse them in water.The L300 FS Cuff is the only component that can be immersed in water to clean. To clean the L300 FS Cuff:1. Remove the L300 RF Stim Unit and, if appropriate, the large cloth electrode.2. If using the L300 hydrogel or cloth electrodes, gently remove the electrodes from the electrode bases. Do not remove the electrode bases. For hydrogel electrodes, replace the electrode covers. 3. Immerse the L300 FS Cuff for 30 minutes in lukewarm water and mild detergent. Do not use a washing machine.4. Rinse the L300 FS Cuff thoroughly under running water.5. Immerse the L300 FS Cuff for an additional 15 minutes in clean, lukewarm water.6. Rinse the L300 FS Cuff again under running water.7. Gently blot excess moisture from the L300 FS Cuff with a towel. Do not wring the L300 FS Cuff. Lay the L300 FS Cuff flat in the shade to dry. (Do not hang dry.) Drying time will vary from 4 to 12 hours depending on temperature and humidity. For faster drying, place the L300 FS Cuff in front of a circulating cold-air fan. Do not use a hot-air dryer or other heat source to dry.8. When the L300 FS Cuff is completely dry, insert the L300 RF Stim Unit and attach the electrode(s).
109Chapter 9 - Maintenance and CleaningDisinfecting the L300 Plus ComponentsAll NESS L300 Plus System Kit components excluding the L300 FS Cuff and the Thigh FS Cuff straps may be disinfected using CaviWipes™ (Metrex, Orange, CA) per the manufacturer’s instructions. Metrex products are sold through authorized dealers worldwide. If you have difficulty locating Metrex CaviWipes, please call the Bioness Client Relations Department at (800) 211-9136, Option 3.To disinfect the L300 Plus System components:1. Clean the surface that faces the skin with a wet CaviWipes disinfection wipe.Note: Read the manufacturer's instructions for use, and follow standard precautions for personal protection as appropriate.2. Using one or more new CaviWipes, wipe the surface again, thoroughly, for 3 minutes. The surface should be visibly wet.
110 User's Guide

Navigation menu