Billionton Systems BT56R-BN Bluetooth Modem User Manual Bluetooth Modem

Billionton Systems, Inc. Bluetooth Modem Bluetooth Modem

UserManual.wiki >

Billionton Systems >

BT56R BN User Manual

users manual

Bluetooth ModemAppendix A. AT Command¡@¡@1. IntroductionThe Bluetooth 56k wireless modem provide a standard V90 Modem for WAN communication and access to Internet. This device is capable of running a complete Bluetooth software stack and in addition to this there is sufficient memory and processing power to also run the Dial-Up Networking (DUN) and fax Bluetooth software application profiles. This device has been developed as a cost-effective means of providing wireless Internet access in the home or office. Package Contents● Bluetooth 56K Wireless Modem ● AC adapter ● RJ-11 phone cable ● RS-232 Cable (DB-9pin) ● Quick Start Guide ● Driver CD (User's Manual inside)Note: If any of these items are missing from the retail package, contact your supplier immediately.¡@2. Specifications2.1. FeaturesV90 Modem● Data modem ❍ ITU-T V9.0 and K56flex❍ V.34 (33.6 kbps), V.32 bis, V.32, V.22 bis, V.22, V.23, and V. 21; Bell 212A and file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (2 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem103❍ V.42 LAPM, MNP 2-4, and MNP 10 error correction❍ V.42 bis and MNP 5 data compression❍ MNP 10ECTM enhanced cellular performance❍ V.250 and V.251 commands● Fax modem send and receive rates up to 14.4 kbps ❍ V.17, V.29, V.27 ter, and V.21 channel 2❍ EIA/TIA 578 Class 1 and T.31 Class 1.0, and EIA/TIA 578 Class 2 commands● V.80 synchronous access mode supports host-based communication protocols with H.324 interface● Telephony/TAM , V.253 commands ❍ 2-bit and 4-bit Conexant ADPCM, 8-bit linear PCM, and 4-bit IMA coding❍ 8 kHz sample rate , Concurrent DTMF and Ring● Flow control and speed buffering● Automatic format/speed sensing● V.22bis fast connect● Built-in host/DTE interface with speeds up to 230.4 kbps● Serial sync / Async data; parallel Async data● Meets worldwide DC VI Masks requirementsBluetooth Module● Using BlueCore2-External in conjunction with a host ARM processor. ● The Bluetooth stack software is split at the conventional HCI point ● Bluetooth Specification V1.X ● CSR Blue Core2 , External Signal chip Bluetooth System. ● Full speed Class2(1) . ● Full embedded to RF COMM ● Virtually Class 1 performance with no external power amplifier ● Authentication is a mandatory feature of the Dial-up Networking and fax profiles.2.2. Specifications● Communication software compatible AT command sets● 3.3V low power consumption● Bluetooth or D-SUB9 interface Switch● Provides LEDs for showing status information2.3. Certification● FCC Part 68 , 15 and CEfile:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (3 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem2.4. Environment Operating Ranges ● Operation : 25 ~ 80¢J● Storage : -5 ~ 90¢J2.5. Power Consumption● Operation : 0.85w(Avg) 1.14W (Max)● Standby : 0.26W2.6. LED Indication● Power LED indicator : Power ON ● Link LED indicator : Bluetooth Link with Host● ACT LED indicator : Bluetooth Data TX/RX● OH LED indicator : Modem OFF Hook● TX LED indicator : Modem Data TX● RX LED indicator : Modem Data RX2.7. Driver Support ● Windows 98SE, Windows ME, Windows 2000, Windows XP¡@3. Product Shapefile:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (4 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem ¡@file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (5 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem¡@1. Power LED indicator 2. Link LED indicator3. ACT LED indicator4. OH LED indicator5. TX LED indicator6. RX LED indicator7. Reset Button 8. Antenna9. RJ-11 Socket10. Switch11. RS-232 Connector12. Power Jack4. Bluetooth Modem ModeSwitch to "BT" side.Connect the telephone line to the RJ-11 socket and plug AC adapter to an power outlet.Please refer your Bluetooth software to operate the Bluetooth modem.¡@5. 56K Modem ModeSwitch to "RS-232" side.5.1 Windows98 Installationfile:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (6 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem1. Connect the telephone line to the RJ-11 socket and plug AC adapter to an power outlet, then plug RS-232 cable male head to RS-232 connector of Bluetooth 56K Wireless Modem and plug female head to your PC.2. Make sure your PC is powered on and that you are running the Windows operating system. Then system will recognize the device and display the "Add New Hardware Wizard" dialog box. Please insert the driver CD and then click the "Next" button.3. Select "Search for the best driver for your device (Recommended)", then click the "Next" button.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (7 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

$Bluetooth Modem4. Select "Specify a location" and type "G:\Modem" (where G:\ is the path of your CD-ROM drive) in the location or you can click the "Browse" button to select, then click the "Next" button.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (8 / 43) [2003/2/20 ､U､ﾈ 02:39:38]$

Bluetooth Modem5. Click the "Next" button, the driver then installs itself.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (9 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem6. Click the "Finish" button to complete the installation process.5.2 WindowsME Installation1. Connect the telephone line to the RJ-11 socket and plug AC adapter to an power outlet, then plug RS-232 cable male head to RS-232 connector of Bluetooth 56K Wireless Modem and plug female head to your PC.2. Make sure your PC is powered on and that you are running the Windows operating system. Then system will recognize the device and display the "Add New Hardware Wizard" dialog box. Please insert the driver CD and then click the "Next" button.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (10 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

$Bluetooth Modem3. Select "Search for the best driver for your device." then choose "Specify a location" and type "G:\Modem" (where G:\ is the path of your CD-ROM drive) in the location or you can click the "Browse" button to select, then click the "Next" button.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (11 / 43) [2003/2/20 ､U､ﾈ 02:39:38]$

Bluetooth Modem4. Click the "Next" button, the driver then installs itself.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (12 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem5. Click the "Finish" button to complete the installation process.5.3 Windows2000 Installation1. Connect the telephone line to the RJ-11 socket and plug AC adapter to an power outlet, then plug RS-232 cable male head to RS-232 connector of Bluetooth 56K Wireless Modem and plug female head to your PC.2. Make sure your PC is powered on and that you are running the Windows operating system. Then system will recognize the device and display the "Found New Hardware Wizard" dialog box. Please insert the driver CD then click the "Next" button.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (13 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem2. Select "Install the software automatically (Recommended)", then click the "Next" button.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (14 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem3. Select "Specify a location" then click the "Next" button.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (15 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

$Bluetooth Modem4. Type "G:\Modem" (where G:\ is the path of your CD-ROM drive) in the location or you can click the "Browse" button to select, then click the "Next" button.5. Click the "Next" button, the driver then installs itself.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (16 / 43) [2003/2/20 ､U､ﾈ 02:39:38]$

Bluetooth Modem6. Windows will search for and recognize the driver of the device, then display one message. Please click the "Yes" button. Windows will then automatically copy the driver files and related files into the system.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (17 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem7. After copying the driver files, click the "Finish" button to complete the installation process.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (18 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem¡@¡@5.4 WindowsXP Installation1. Connect the telephone line to the RJ-11 socket and plug AC adapter to an power outlet, then plug RS-232 cable male head to RS-232 connector of Bluetooth 56K Wireless Modem and plug female head to your PC.2. Make sure your PC is powered on and that you are running the Windows operating system. Then system will recognize the device and display the "Found New Hardware Wizard" dialog box. Select "Install from a list or specific location (Advanced)", insert the driver CD then click the "Next" button.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (19 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

$Bluetooth Modem3. Select "Search for the best driver in these locations." and choose "Include this location in the search:" then type "F:\Modem" in the location. Click the "Next" button. file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (20 / 43) [2003/2/20 ､U､ﾈ 02:39:38]$

Bluetooth Modem4. Windows will search for and recognize the driver of the device, then display one message. Please click the "Continue Anyway" button. Windows will then automatically copy the driver files and related files into the system.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (21 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem5. After copying the driver files, click the "Finish" button to complete the installation process.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (22 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem¡@5.5 SuperVoice software Installation¡@SuperVoice provides data and voice access via connect to internet that capabilities to Microsoft based operating system. To install SuperVoice for the first time on a system:1. The program will autorun when you insert the software CD to CD drive of your PC.2. Follow the directions displayed in the SuperVoice installation program. Specify a path name in which you want SuperVoice to be installed.3. Reboot your system when prompted by the setup program. Once the system is running again, you can use SuperVoice software.¡@file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (23 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth ModemAppendix A. AT CommandCommand Function Default Range Reportedby &VnA/ ** Repeat last command none - noA Answer none - noBn * Select ITU-T or Bell 1 0-3 yesB0 Selects ITU-T V.22 at 1200 bps and ITU-T V.21 at 300 bps¡@ ¡@ ¡@B1 Select Bell 212A at 1200 bps and Bell 103J at 300 bps ¡@ ¡@ ¡@B2 Selects ITU-T V.23 only. The originating modem transmits to 75 bps (and receives at 1200 bps); the answering modem receives at 75 bps (and transmits at 1200 bps)¡@ ¡@ ¡@B3 Select ITU-T V.23 only. The originating modem transmits at 1200 bps (and receives at 75 bps); the answering modem receives at 1200 bps (and transmits at 75 bps)¡@ ¡@ ¡@Cn Carrier control option 1 0,1 noC0 Transmit carrier always off ¡@ ¡@ ¡@file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (24 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth ModemC1 Normal transmit carrier ¡@ ¡@ ¡@D Dial command none - noEn * Command mode echo 1 0,1 yesE0 Disable echo ¡@ ¡@ ¡@E1 Enable echo ¡@ ¡@ ¡@Fn Online echo 1 0,1 noF0 Enables online echo ¡@ ¡@ ¡@F1 Disables online echo ¡@ ¡@ ¡@Hn Switch hook control 0 0,1 noH0 Hangs up the telephone line ¡@ ¡@ ¡@H1 Picks up the telephone line ¡@ ¡@ ¡@In Identification/checksum option 0 0-14, 20-24noI0 Reports product code ¡@ ¡@ ¡@file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (25 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth ModemI1 Reports modem chip firmware version ¡@ ¡@ ¡@I2 Verifies ROM checksum ¡@ ¡@ ¡@I3 Reports chipset name ¡@ ¡@ ¡@I4 Reserved ¡@ ¡@ ¡@I5 Reserved for modem chip hardware configuration ¡@ ¡@ ¡@I6 Country code ¡@ ¡@ ¡@I7 Version of board manufacturer firmware ¡@ ¡@ ¡@I8 Features of modem firmware ¡@ ¡@ ¡@I10 Modem board configuration-bits set by board manufacturer ¡@ ¡@ ¡@I11 Modem board configuration-bits set by board manufacturer ¡@ ¡@ ¡@I14 SAFE device ¡@ ¡@ ¡@I20 Cirrus Logic silicon version ¡@ ¡@ ¡@I21 Cirrus Logic firmware version ¡@ ¡@ ¡@I22 Cirrus Logic manufacturer name ¡@ ¡@ ¡@file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (26 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth ModemI23 Cirrus Logic product model ¡@ ¡@ ¡@Ln * Speaker volume control 2 0-3 yesL0 Low speaker volume ¡@ ¡@ ¡@L1 Low speaker volume ¡@ ¡@ ¡@L2 Medium speaker volume ¡@ ¡@ ¡@L3 High speaker volume ¡@ ¡@ ¡@Mn * Speaker control 1 0-3 yesM0 Speaker always off ¡@ ¡@ ¡@M1 Speaker on until carrier present ¡@ ¡@ ¡@M2 Speaker always on ¡@ ¡@ ¡@M3 Speaker off during dialing; speaker on until carrier present ¡@ ¡@ ¡@Nn * Select data rate handshake 1 0,1 yesN0 Handshake only at DTE-to-modem data rate ¡@ ¡@ ¡@N1 Begins handshake at DTE-to-modem data rate and falls to highest compatible rate ¡@ ¡@ ¡@file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (27 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth ModemOn Go online 0 0,1 noO0 Returns modem to data mode ¡@ ¡@ ¡@O1 Retrains equalizer and then returns to data mode ¡@ ¡@ ¡@P * Select pulse dialing none - yesQn * Result code display control 0 0,1 yesQ0 Enables result codes ¡@ ¡@ ¡@Q1 Disables result codes ¡@ ¡@ ¡@Sn Select an S-register none 0-37 noSn=X Write to an S-register none n=0-37 X=0-255noSn? Read from an S-register none 0-37 noT * Select tone dialing none - noVn Result code form 1 0,1 yesV0 Choose numeric form ¡@ ¡@ ¡@file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (28 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth ModemV1 Choose verbose (text) form ¡@ ¡@ ¡@Wn * Response code data rate 0 0-4 yesW0 Reports DTE speed response codes ¡@ ¡@ ¡@W1 Reports DTE speed response codes ¡@ ¡@ ¡@W2 Reports DTE speed response codes ¡@ ¡@ ¡@W3 Reports DTE speed response codes and information on error correction and data compression¡@ ¡@ ¡@W4 Reports protocol, data compression, and DTE data rate ¡@ ¡@ ¡@Xn * Result code type 4 0-4 yesX0 Enable result codes 0-4; disables detection of busy and dial tone ¡@ ¡@ ¡@X1 Enables result codes 0-5, 10, and above; disables busy and dial tone detection ¡@ ¡@ ¡@X2 Enables result codes 0-6 and 10 and above; disables busy detection and enables dial tone detection¡@ ¡@ ¡@X3 Enables result codes 0-5, 7, and 10 and above; enables busy detection and disables dial tone detection¡@ ¡@ ¡@X4 Enable result codes 0-7 and 10 and above; enables busy and dial tone detection ¡@ ¡@ ¡@file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (29 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem&F Load factory defaults none - no&Gn * Guard tone option (1200 bps and 2400 bps only) 0 0-2 yes&G0 Disables guard tone ¡@ ¡@ ¡@&G1 Enables 500-Hz guard tone ¡@ ¡@ ¡@&G2 Enables 1800-Hz guard tone ¡@ ¡@ ¡@&Jn * Auxiliary relay control 0 0-1 yes&J0 Auxiliary relay never operated ¡@ ¡@ ¡@&J1 Activates auxiliary relay when modem is offhook ¡@ ¡@ ¡@&Kn Select serial port flow control 3 0, 3, 4 yes&K0 Disables flow control ¡@ ¡@ ¡@&K3 Bidirectional hardware flow control ¡@ ¡@ ¡@&K4 XON/XOFF software flow control ¡@ ¡@ ¡@&M0 * Communication mode option-modem supports only async mode 0 0 no&Pn * Dial pulse ratio 0 0,1 yesfile:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (31 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

Bluetooth Modem-Cn * Generate data modem calling tone 1 0-2 yes-Cn Calling tone disabled ¡@ ¡@ ¡@-C1 1300-Hz calling tone enabled ¡@ ¡@ ¡@-C2 V.8 calling tone and 1300-Hz calling tone ¡@ ¡@ ¡@+GMI? Identify modem manufacturer none - no+GMM? Identify product model none - no+GMR? Identify product revision none - no+MS=m Modulation selections V90, 1, 300,0 See note + no+ See full command description in the CL-MD56XX Programmer's Guide for parameter ranges. For data mode, the factory default setting is AT+MS=V90, 1, 300, 0 to send at speeds of 31,200 bps and below and receive at speeds of 53,333 bps and below.* Value saved in NVRAM.** Command not preceded by an 'AT'.Error Correction and Data CompressionV.42/V.42 bis MNP AT CommandsCommand Function Default Range Reported by &Vnfile:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (34 / 43) [2003/2/20 ､U､ﾈ 02:39:38]

$Bluetooth Modem&An * Set auto-reliable fallback character 13 0-127 yes%Cn * MNP 5 data compression control 1 0,1 yes%C0 No compression ¡@ ¡@ ¡@%C1 Enables MNP 5 data compression ¡@ ¡@ ¡@\An * MNP block size 3 0-3 yes\A0 Maximum 64 characters ¡@ ¡@ ¡@\A1 Maximum 128 characters ¡@ ¡@ ¡@\A2 Maximum 192 characters ¡@ ¡@ ¡@\A3 Maximum 256 characters ¡@ ¡@ ¡@\Bn * Transmit break none 0-9 no\Cn * Set auto-reliable buffer 0 0-2 yes\C0 No data buffering ¡@ ¡@ ¡@\C1 Four-second buffer until 200 characters in the buffer or detection of a SYN character ¡@ ¡@ ¡@\C2 No buffering. Connects non-V.42 modems to V.42 modem ¡@ ¡@ ¡@file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (35 / 43) [2003/2/20 ､U､ﾈ 02:39:38]$

$Bluetooth Modem\Gn * Set modem port flow control 0 0, 1 yes\G0 Disables port flow control ¡@ ¡@ ¡@\G1 Sets port flow control to XON/XOFF ¡@ ¡@ ¡@\Jn * bps rate adjust control 0 0, 1 yes\J0 Disable rate adjust ¡@ ¡@ ¡@\J1 Enable rate adjust ¡@ ¡@ ¡@\Kn * Set break control 5 0-5 yesIn connect state, transmits break to remote (if in reliable mode):\K0, 2, 4 Enters command mode, no break sent ¡@ ¡@ ¡@\K1 Destructive/expedited ¡@ ¡@ ¡@\K3 Nondestructive/expedited ¡@ ¡@ ¡@\K5 Nondestructive/nonexpedited ¡@ ¡@ ¡@In command state, transmits break to remote (if in reliable mode):\K0, 1 Destructive/expedited ¡@ ¡@ ¡@\K2, 3 Nondestructive/expedited ¡@ ¡@ ¡@file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (36 / 43) [2003/2/20 ､U､ﾈ 02:39:38]$

$Bluetooth Modem\K4, 5 Nondestructive/nonexpedited ¡@ ¡@ ¡@In connect state, receives break at modem port (if in direct mode):\K0, 2, 4 Immediately sends break and enters command state ¡@ ¡@ ¡@\K1, 3, 5 Immediately sends the break through ¡@ ¡@ ¡@In connect state, receives break at modem port and sends to serial port:\K0, 1 Destructive/expedited ¡@ ¡@ ¡@\K2, 3 Nondestructive/expedited ¡@ ¡@ ¡@\K4, 5 Nondestructive/nonexpedited ¡@ ¡@ ¡@\Nn * Set operating mode 3 0-4 yes\N0, 1 Selects Buffer (Normal) mode with speed buffering ¡@ ¡@ ¡@\N2 Selects MNP reliable mode ¡@ ¡@ ¡@\N3 Selects V.42 auto-reliable mode ¡@ ¡@ ¡@\N4 Selects V.42 reliable mode ¡@ ¡@ ¡@\O Originate reliable link none - no\Qn * Set serial port flow control 3 0-3 yesfile:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (37 / 43) [2003/2/20 ､U､ﾈ 02:39:39]$

$Bluetooth Modem\Q0 Disables flow control ¡@ ¡@ ¡@\Q1 XON/XOFF software flow control ¡@ ¡@ ¡@\Q2 Unidirectional hardware flow control ¡@ ¡@ ¡@\Q3 Bidirectional hardware flow control ¡@ ¡@ ¡@\T0 * Disables inactivity timer 0 0-90 yes\U Accept reliable link none - no\Xn * Set XON/XOFF pass-through 0 0, 1 yes\X0 Processes flow control characters ¡@ ¡@ ¡@\X1 Processes flow control characters and passes to local or remote ¡@ ¡@ ¡@\Y Switch to reliable mode none - no\Z Switch to normal mode none - no-Jn * Set V.42 detect phase 1 0, 1 yes-J0 Disables the V.42 detect phase ¡@ ¡@ ¡@-J1 Enables the V.42 detect phase ¡@ ¡@ ¡@file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (38 / 43) [2003/2/20 ､U､ﾈ 02:39:39]$

$Bluetooth Modem"Hn * V.42 bis compression control 3 0-3 yes"H0 Disables V.42 bis ¡@ ¡@ ¡@"H1 Enables V.42 bis only when transmitting data ¡@ ¡@ ¡@"H2 Enables V.42 bis only when receiving data ¡@ ¡@ ¡@"H3 Enables V.42 bis for both transmitting and receiving data ¡@ ¡@ ¡@"On V.42 bis string length 32 6-250 yes* Value saved in NVRAMThe fax modem support four operating modes: buffer (normal), MNP reliable, V.42 auto-reliable, and V.42 reliable. These four modes are selected by the \Nn command. They allow the DCE to communicate with remote modems that may or may not support error correction and data compression. Speed buffering, which is used for all operating modes, allows the DTE-to-modem data rate to be different from the modem-to-modem data rate. This is accomplished by using transmitter and receiver buffers in the modem. Thus the DTE-to-modem data rate can be set for 2400 bps when the modem-to-modem data rate is 300 bps without causing any data errors. In all data modes, the DTE-to-modem data rate can be set for any valid speed between 300 bps to 115,200 bps (that is, the modem autobouds up to 115,200 bps). The modem-to-modem data rates can be set to 300, 1200, 2400, 4800, 7200, 9600, 12,200, 14,400, 16,800, 19,200, 21,600, 24,000, 26,400, 28,800, 31,200, and 33,600 bps. Each operating mode is explained in more detail in the following tables.Operating ModesModeFeatures ¡@Buffer (normal) \N0 or \N1No error correction/data compression, but speed buffering is supported.file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (39 / 43) [2003/2/20 ､U､ﾈ 02:39:39]$

$Bluetooth ModemMNP Reliable \N2MNP 2-5 connection only. If an MNP connection cannot be established, the modem hangs up.V.42 Auto-Reliable \N3V.42/V.42 bis with fallback to MNP 2-5 or normal mode.V.42 Reliable \N4V.42, V.42 bit or MNP 2-5 only connection. If a V.42/V.42 bis/MNP 2-5 connection cannot be established, the modem hangs up.Connection types corresponding to \Nn settings are provided in below.¡@Resulting \Nn Connection Types¡@ \Nn Settings (Answer Modem)\Nn Settings(Originate Modem)\N0 or \N1(Buffer)\N2(MNP Reliable)\N3(V.42 Autoreliable)\N4(V.42 Reliable)\N0 or \N1(Buffer)Buffer (normal)modeModem hangs up Buffer (normal)modeModem hangs up\N2(MNP Reliable)Modem hangs up MNP 2-5 MNP 2-5 MNP 2-5file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (40 / 43) [2003/2/20 ､U､ﾈ 02:39:39]$

$Bluetooth Modem\N3(V.42 Auto-reliable)Buffer (normal)modeV.42/V.42 bis V.42/V.42 bis V.42/V.42 bis\N4(V.42 Reliable)Modem hangs up V.42/V.42 bis V.42/V.42bis V.42/V.42 bisNOTES:1) MNP 5 requires the modem to be configured for %C1.2) V.42 bis requires the modem to be configured for "H3.3) Refer to \Cn and %An commands for more information about auto-reliable mode.The list of command needs to enter a specific error correction or data compression mode are as follow: V.42 bis with fallback to MNP 5, &F \N3 or \N3 "H3 %C1 MNP2-4 or V.42:V.42 bis with fallback to V.42/MNP2-4: &F \N4 %C0 or \N4 %C0 "H3 -J1V.42 bis only: &F \N4 -J0 or \N4 -J0 "H3 V.42 only: &F \N4 -J0 "H0 or \N4 -J0 "H0MNP5 with fallback to MNP2-4: &F \N2 or \N2 %C1MNP2-4 only: &F \N2 %C0 or \N2 %C0Fax Class 1 AT CommandsThe 56-kbps fax modem implements the EIA-578 data/fax Class 1 AT command set standard. This AT command set allows a DTE (with Class 1 communication software) and a CL-MD56XX-based modem to communicated with Group 3 fax machines. In addition, these product provide fax identity and test commands. This manual should be used with the Class 1 Fax Application Note and the specifications for EIA/TIA-578, ITU-T T.30, and T.4. The Cirrus Logic Class 1 Fax Application Note shows several examples of how the use the fax AT commands and how to originate and answer a fax call.¡@file:///C|/Documents and Settings/Alcee/面/ww/Manual.htm (41 / 43) [2003/2/20 ､U､ﾈ 02:39:39]$

Billionton Systems BT56R-BN Bluetooth Modem User Manual Bluetooth Modem

Billionton Systems, Inc. Bluetooth Modem Bluetooth Modem

users manual

Navigation menu

Namespaces

Views

Navigation