BiSRO ASF-301 One-Way Remote Control User Manual UserManual bisro

BiSRO Co.,Ltd. One-Way Remote Control UserManual bisro

Users Manual

Before you commence using your system, please read completely.U s e r M a n u a lALD-401 / ASF-301www.signca.comSBC High Tech Center 3F, 932 Wongok-Dong, Danwon-Gu, Ansan-Si, Gyeonggi-Do, Korea+82-31-491-0226
▶Antenna Module▶Remote ControlThank you for purchasing our product. Our systems have all been designed and tested to be compatible with the earliest to latest vehicles available throughout the world. Our primary goal was to provide a reliable and stable product. Our secondary goal was to ensure that our systems are easy to install. Our final goal was to provide features that would benefit the user and installer. We are confident that our products will meet and exceed your expectations. We are constantly working hard in order to research, design, and build next generation products. We would not expect anything less since we use our products in our own vehicles.MIC MarkCaution!!Read CarefullyThe user and installer should completely read the User Manual, Installation Manual, and the vehicle’s manual completely before installing and operating this system. Not reading the manuals completely may result in injury or damage to the user(s), installer(s), and/or the vehicle. Installation and use of this system is acknowledgment that the user and installer have fully read the manuals and indemnify Zenesis Alarms from any injuries or damages resulting from wrong use of our system. Please take the following precautions.FCC ID:MIC Mark: FCC ID:MIC Mark:MIC When using remote start, place the gear in Park(P) ( au t o ma t i c t r a ns m i s s i o n ) o r N e u tr a l ( ma n u al transmission) and set the Emergency Brake (either side hand brake or foot brake).The transmission (Tx) and reception (Rx) distance will vary from interference from other radio signals.If any defects are discovered, do not open or attempt to repair the system. Ask the installer for assistance.Zenesis Alarms will not be responsible for any theft and/or damages to your vehicle.The installer of this system will be responsible for any injuries and/or damages resulting from incorrect installation.The user of this system will be responsible for any injuries and/or damages resulting from misuse.1.2.3.4.5.6.
ContentsIntroduction1. System Contents2. Remote Control Button Layout3. Remote Control Battery Replacement4. Remote Control Button Introduction891011Introduction8910111. System Contents2. Remote Control Button Layout3. Remote Control Battery Replacement4. Remote Control Button IntroductionCONTENTSIntroduction7▶ Warranty Card 21Secondary Features1. User Option Programming2. Program Remote Control to System3. Remote Start Reservation4. Option 1 / Option 2 Input5. Aux 1 Output6. Aux 2 Output7. Shock Sensor8. Shock Sensor Sensitivity 1818191919192020Primary Features1. Lock (Arm) / Unlock (Disarm)2. Remote Start 3. Trunk Release4. Status (ALD-401)5. Panic 6. Siren Mute ON/OFF 7. Valet Mode ON/OFF8. Remote Control Beep ON/OFF 9. Ignition Lock ON/OFF10. Paging ON/OFF11. Passive Arm ON/OFF12. Safety Rearm ON/OFF13. Cold Start ON/OFF14. Turbo Timer ON/OFF15. Temperature Status (ALD-401)(ALD-401)(ALD-401)131314141414151515161616
Introduction9Introduction8AntennaLock / Arm Unlock / DisarmRemote Start Trunk Release→LED1. System ContentsRemote Control x 2(1 x 2-way & 1 x 1-way)Control Module / “Brain” AntennaModuleManualsUser / InstallationShock Sensor202A / 202ASSiren202A / 202ASWiring Harness2. Remote Control Button Layout±20ppm/year28×12×68.7mm▶SpecificationsRadiationDimensions-40℃ ~ +80℃15g (without battery)Temp.WeightStickers2-way Remote Control
Introduction10Introduction11③ Once the rear panel is removed, you will see the PCB and the battery. Follow the direction of “Remove Battery” to safely remove it. Slide the new battery in the direction of “Insert Battery”. Use a 3V CR2032 battery only. ※ Caution : Ensure that the polarity of the battery is correct. The positive (+) terminal should be facing towards you.RemoveBatteryInsertBattery++-3. Remote Control Battery Replacement① Use a 3mm Philips screwdriver to remove the screw on the rear panel of the remote control.② Use a hand to hold the front panel. Use your free hand to gently pull the rear panel off by prying the key holder.4. Remote Control Button IntroductionLock (Arm)Unlock (Disarm)StatusPanicRemote Start ON/OFFTrunk ReleaseSiren ON/OFFRemote Control Addition (Normal)Remote Control Addition (Door lock after Remote Start)Aux 2 OutputAux 1 OutputUser Programmable OptionsPassive Lock (Arm) ON/OFFValet Mode ON/OFFSafety Re-lock (Rearm) ON/OFFIgnition Lock ON/OFFCold Start Timer ON/OFFTurbo Timer ON/OFFButton(s) Description0.5 sec0.5 sec0.5 sec2 sec2 sec2 sec4 sec0.5 sec0.5 sec0.5 sec0.5 sec2 sec4 sec4 sec4 sec4 sec4 sec4 secDuration+++++++++++123456789101112131415161718Item- + (0.5 sec ) 1 Remote Control LED Blink(2 sec) 2 Remote Control LED Blinks( 4 sec) 3 Remote Control LED BlinksPress both buttons at the same time for the specified duration.Note
Vehicle 1 parking light flash & 1 siren chirp Remote Control1 blink & 1 beepPrimary Features13NotePrimary Features123) Arm / Disarm Status (202A / 202AS)2) Door Unlock / Disarm1. Door Lock / Arm1) Door Lock / Arm ·If the Trunk and/or Hood is open while Arming (202A / 202AS), the siren will sound immediately. ·If the Door is open while arming (202A / 202AS), the siren will sound after 45 seconds.0.5 sec0.5 sec·Failed Door Lock / Arm from Open Trunk, Hood, and/or Door·Successful Door Lock / Arm·Successful Unlock / DisarmMain SystemFeatures2. Remote Start ·If the button is pressed for 2 seconds while Remote Start is ON, Remote Start will turn OFF.·After the door(s) is(are) open after Remote Start, the key must be put into the key cylinder within 2 minutes or the engine will turn OFF.·The default Remote Start engine running time is 5 minutes. The time can be changed through the User Programmable Options on page 18.2 sec·Failed Remote Start·Successful Remote Start ·Siren duration can be programmed through the User Programmable Options on page 18.※ After the alarm is triggered... ① Button → The siren will stop. 5 siren chirps and fast LED flashes on the Antenna Module will confirm button press. ② Button → The siren will stop. The system will be disarmed with 2 parking light flashes & 2 siren chirps. ③ Door Open and Closed → The LED on the Antenna Module will stop flashing quickly. ④ Button → The system will Arm normally.StatusArmed ModeDisarmed Mode Triggered Alarm after ArmingAntenna Module LEDNormal FlashNo FlashFast FlashVehicle3 parking light flashes & 3 siren chirps4 parking light flashes & 4 siren chirps7 parking light flashes & 7 siren chirps1 parking light flash & 1 siren chirpReason for FailureKey is in key cylinder at ON positionDoor is openTrunk and/or hood is openRemote start reservation has failedDo not use the Remote Start feature if the vehicle is in an enclosed area. Do not use the Remote Startfeature where laws prevent its usage. Do not turn the key to the Start position or else damage may be doneto the starter motor.Since the Doors cannot be locked and the system cannot be armed (202A / 202AS) while theTrunk and/or Hood is open, ensure that the Trunk and Hood are closed before Locking / Arming.Caution1313141414141515151616161. Lock (Arm) / Unlock (Disarm)2. Remote Start3. Trunk Release4. Status (ALD-401)5. Panic6. Siren Mute ON/OFF (ALD-401)7. Valet Mode ON/OFF8. Remote Control Beep ON/OFF (ALD-401)9. Ignition Lock ON/OFF10. Paging ON/OFF11. Passive Arm ON/OFF12. Safety Rearm ON/OFF13. Cold Start ON/OFF14. Turbo Timer ON/OFFVehicle 4 parking light flashes & 4 siren chirps Remote Control1 blink & 1 beepVehicle 2 parking light flashes & 2 siren chirps Remote Control1 blinks & 2 beepsVehicle 5 parking light flashes & 5 siren chirps Remote Control1 blink & start toneRemote ControlXXXXXXXXXXXX
Vehicle 2 parking light flashes & 2 siren chirps Remote Control2 blinks & 2 beepsPrimary Features15Primary Features147. Valet Mode ON/OFF + 4 sec3. Trunk Release·Trunk release will unlock the door(s) and disarm (202A / 202AS) the system.2 sec4. Status (ALD-401) 0.5 sec5. Panic·If there is a potential threat, you can alert those around by using this feature.·The siren will sound for 2 minutes and the parking lights will flash. ·Press either the or the button to turn OFF Panic.2 sec·Siren Mute OFF - Siren ON·Siren Mute ON - Siren OFF6. Siren Mute ON/OFF (ALD-401)·All features of the system still function with siren Mute ON.4 secNoteOn manual transmission vehicles, Trunk Release will turn OFF remote start reservation.·Once a door is opened and closed and the door is not locked (system armed) via the remote control, the system will automatically lock (system arm) the doors.·The system will lock (system arm) the doors after 25 seconds of the last door closing. Every 5th seconds, 1 parking light flash and 1 siren chirp will occur. On the 5 occurrence, the doors will lock (system arm).·OFF·ON9. Passive Arm ON/OFF + 4 secIf Passive Arm is ON, always carry the remote control.Caution·OFF·ON▶ Valet Mode via Key (Emergency Shut Off)① Open driver’s side door.② Insert the key and turn to the ON position. Within 3 seconds, turn the key between ACC↔ON 3 times and on the third time leave the key in the ON position. 1 parking light flash and 1 siren chirp will confirm the operation.※ This feature can be used to turn off the alarm with the key if the system has been triggered.※ Valet Mode can only be turned off via the remote control.·When Valet Mode is ON, the siren will be OFF and no features except for lock and unlock will work.·Ignition Lock OFF·Ignition Lock ON - The doors will lock after 20 seconds of driving or the foot brake is pressed.·When the key is turned to the OFF position, the doors will unlock.8. Ignition Lock ON/OFFNoteWhenever the vehicle is being lent to an individual, turning Valet Mode ON is suggested.3 times ·Upon Passive Arming, the button will blink once and 1 beep will sound.StatusRemote Control LEDVehicle 2 parking light flashes & 2 siren chirps Remote Control1 blink & 1 beepVehicle 1 parking light flash & 1 siren chirp Remote Control1 blink & 1 beepVehicle 1 parking light flash & 1 siren chirp Remote Control2 blinks & 2 beepsVehicle 1 parking light flash & 1 siren chirp Remote Control1 blink & 1 beep+ Vehicle 2 parking light flashes & 2 siren chirps Remote Control2 blinks & 2 beeps+ Vehicle 1 parking light flash & 1 siren chirp Remote Control1 + blink & 1 beep+ 4 secVehicle 2 parking light flashes & 2 siren chirps Remote Control2 + blinks & 2 beepsVehicle 1 parking light flash & 1 siren chirp Remote Control1 + blink & 1 beepVehicle 2 parking light flashes & 2 siren chirps Remote Control2 + blinks & 2 beeps
1818191919192020Secondary Features17Primary Features16메뉴구성11. Cold Start Timer ON/OFF·A timer can be set to remote start the car. ※The timer can be set through the User Programmable Options on page 18.·Cold Start Timer OFF·Cold Start Timer ON12. Turbo Timer ON/OFF·This feature will allow turbocharged or supercharged vehicles to cool down by idling the engine for a specified amount of time. Even though the key is turned to the OFF position, the engine will idle.※ The duration for idling can be specified through the User Programmable Options on page 18.+ 4 sec+ 4 sec10. Safety Rearm ON/OFF·If the doors are unlocked (system disarmed) and a door is not opened, the doors will lock (system rearm) after 30 seconds automatically.+ 4 sec·Safety Rearm OFF·Safety Rearm ONPlease ensure that the vehicle is Park (automatic transmission) or Neutral (manualtransmission). Also, ensure that the hand brake or foot brake is engaged..Caution·Turbo Timer OFF·Turbo Timer ON·If Safety Rearm occurs, the button will blink once and 1 beep will sound.Vehicle 1 parking light flash & 1 siren chirp Remote Control1 + blink & 1 beepVehicle 2 parking light flashes & 2 siren chirps Remote Control2 + blinks & 2 beepsVehicle 1 parking light flash & 1 siren chirp Remote Control1 + blink & 1 beepVehicle 2 parking light flashes & 2 siren chirps Remote Control2 + blinks & 2 beepsVehicle 1 parking light flash & 1 siren chirp Remote Control1 + blink & 1 beepVehicle 2 parking light flashes & 2 siren chirps Remote Control2 + blinks & 2 beeps1. User Option Programming2. Program Remote Control to System3. Remote Start Reservation4. Option 1 / Option 2 Input5. Aux 1 Output6. Aux 2 Output7. Shock Sensor 8. Shock Sensor Sensitivity 13. Temperature Status (ALD-401)2 sec·The interior temperature of the vehicle will be displayed as a series of LED’s on the remote control.Temperature Remote Control LEDLess than or equal to -10 °C (14 °F) 1 blink & 1 beep-9 °C (16 °F) to 0 °C (32 °F) 1 + blink & 1 beep1 °C (34 °F) to 10 °C (50 °F) 1 + + blink & 1 beep11 °C (52 °F) to 20 °C (68 °F) 1 + + + blink & 1 beep2 + + + blinks & 2 beepsGreater than 20 °C (68 °F)
4 timesSecondary Features19Secondary Features184. Option 1 / Option 2 Input·Additional sensors can be added to the system using Option 1 and/or Option 2 input(s).·No additional programming is required.·When the sensor(s) is(are) triggered, the parking lights will flash and the siren will sound.5. Aux 1 Output·Aux 1 Output can be used to control other devices. For example, window modules can be added to roll up or roll down windows.· + (0.5 sec) will activate Aux 1 Output. 2 parking light flashes and 2 siren chirps will confirm output. The remote control will blink 2 times and beep 2 times.6. Aux 2 Output2. Program Remote Control to System① Close driver’s side door. Insert key and turn to the ON position.t h ② Turn the key ACC↔ON 4 times within 3 seconds. On the 4 time, leave the key in the ON position.③ 3 parking light flashes and 3 siren chirps will confirm remote control programming mode.④ Press the correct button combination for 0.5 seconds as outlined below. ▶ Typical vehicles + ▶ Vehicles that unlock doors after remote start + ⑤ After each remote control is added, there will be a confirmation of 2 parking light flashes and 2 siren chirps. You can add up to 3 remote controls per system.⑥ Once the key is turned to the OFF position or 10 seconds without adding a remote control passes, the system will exit remote control programming mode.※ Each time a remote control is added, all remote controls must be reprogrammed to the system. Adding a remote control erases previously stored remote controls from the system.Feature Default Option1. User Programmable Options + 2 sec·When you enter programming mode by holding + for 2 seconds, the + LED’s will blink 1 time and 1 beep will be heard. Follow the chart below for programming the options. ※ The Button Combination includes the initial buttons to get into User Programmable Options.3. Remote Start Reservation① Before turning off the engine, put the transmission into Neutral. Ensure that the hand brake or parking brake engaged. Take your foot off the foot brake.② Turn the key to the OFF position. The engine should still be running.③ Exit the vehicle within 2 minutes.④ Once the last door is closed, the engine will turn off. Lock (Arm) the system. Remote start is ready to be used.※ Remote Start Reservation can be changed through the User Programmable Options on page 18.1) Automatic Remote Start Reservation (Default)① Before turning off the engine, put the transmission into Neutral. Ensure that the hand brake or parking brake is engaged. Take your foot off the foot brake.② Press the button for 2 seconds.③ Turn the key to the OFF position. The engine should still be running.④ Exit the vehicle within 2 minutes.⑤ Once the last door is closed, the engine will turn off. Lock (Arm) the system. Remote start is ready to be used.2) 수동예약 (사용자 옵션설정)·Manual transmission vehicles require remote start reservation in order to ensure that the vehicle isproperly prepared for remote start. There are 2 remote start reservation modes: automatic and manual.Please note that automatic and manual do not refer to the transmission type. Rather, automatic andmanual refer to the type of remote start reservation.+ 2 secRemote Start Run TimeDiesel Warm Up TimeSiren Sound TimeTurbo Timer TimeRemote Start ReservationCold Start Timer Time15 min10 sec70 sec5 minManual2 hours25 min5 sec100 sec10 min3 hours→→→→→→→→→→→→OptionOptionOptionOptionOptionOption++++++ (2 sec) (2 sec) (2 sec) (2 sec) (2 sec) (2 sec)→→→→→→5 min15 sec30 sec2 minAutomatic1 hourFeature Button CombinationOptions→ Default Values.※ Each button must be pressed within 5 seconds of each other or else User Programmable mode will terminate.·Aux 2 Output can be used to control other devices. For example, window modules can be added to roll up or roll down windows.· + (0.5 sec) will activate Aux 2 Output. 2 parking light flashes and 2 siren chirps will confirm output. The remote control will blink 2 times and beep 2 times.
20Warranty CardThis warranty card must be completed and mailed to be eligible for warranty coverage.The Control Module has a limited lifetime warranty. All other parts have a limited 1year warranty. For full details, please visit www.zenesisalarms.com.Mail this card to:Zenesis AlarmsXXXXXXXXXXSecondary Features7. Shock Sensor·The dual stage shock sensor can detect 2 types of shock: light and hard. Light shocks will result in siren chirps and parking light flashes. Hard shocks will result in the system being triggered. Sustained light shocks will also trigger the system.8. Shock Sensor Sensitivity·The sensitivity of the shock sensor can be controlled by turning a dial on the shock sensor module.·Turn the dial according to the amount of sensitivity that is desired. Keep in mind that turning the sensitivity to its maximum can result in false alarms. Test the setting by arming the system and tapping the shock sensor. Model NumberOwner’s NameOwner’s AddressOwner’s PhoneDate of PurchaseDate of InstallRetailer NameRetailer AddressRetailer’s PhoneInstaller NameInstaller AddressInstaller’s Phone

Navigation menu