BiSRO ALC-502G PART15 REMOTE CONTROL/SECURITY DEVICE TRANSCEIVER (TWO-WAY CAR REMOTE CONTROLLER) User Manual

BiSRO Co.,Ltd. PART15 REMOTE CONTROL/SECURITY DEVICE TRANSCEIVER (TWO-WAY CAR REMOTE CONTROLLER)

Users Manual

ZN-502 A/S/AS USER MANUAL
Statement : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful Interference, and (2) this device must accept any interference received, Including interference that may cause undesired operation. The below a two product is market with a one Box Above product type is transceiver, accordingly the receiver portion of the respectively product is proceed a DoC under the Verification procedure Thank you for purchasing our product. Our systems have all been designed and tested to be compatible with the earliest to latest vehicles available throughout the world. Our primary goal was to provide a reliable and stable product. Our secondary goal was to ensure that our systems are easy to install. Our final goal was to provide features that would benefit the user and installer. We are confident that our products will meet and exceed your expectations. We are constantly working to research, design, and build next generation products. We would not expect anything less since we use our products in our own vehicles. - Two-way Remote Controller FCC ID: WJ3ALC-502G - Two-way Main Controller FCC ID: WJ3MB-SFG 2
CAUTION! PLEASE READ CAREFULLY This device under provision section 15.21 of FCC Rule Part 15 that changes or modiications not epressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment. The user and installer should completely read the User Manual, Installation Manual, and the vehicle’s manual completely before installing and operating this system. Not reading the manuals completely may result in injury or damage to the user(s), installer(s), and/or the vehicle. Installation and use of this system is acknowledgment that the user and installer have fully read the manuals and indemnify Zenesis Electronics Corporation from any injuries or damages resulting from wrong use and/or installation of our system. Please take the following minimum precautions. 1. When using remote start, place the gear in Park(P) (automatic transmission) or Neutral (manual transmission) and set the parking brake (emergency brake). 2. The transmission (Tx) and reception (Rx) distance will vary from interference from other radio signals. 3. If any defects are discovered, do not open or attempt to repair the system. Ask the installer for assistance. 4. Zenesis Electronics Corporation will not be responsible for any theft and/or damages to your vehicle. 5. The user of this system will be responsible for any injuries and/or damages resulting from misuse. 6. Zenesis Electronics Corporation does not condone the installation of ANY remote starter equipped product into a convertible or open-concept type vehicle. 3
CONTENTS 1. Introduction 1.1 System Contents 6 1.2 Remote Control Button Layout 7 1.3 LCD Display Introduction 8 1.4 Remote Control Button Introduction 9 2. Primary Features 2.1 Door Lock (Arm) 11 2.2 Door Unlock (Disarm) 11 2.3 Arm / Disarm Status 11 2.4 Car Find & Status 12 2.5 LCD Screen Status 12 2.6 Panic 12 2.7 Remote Start 13 2.8 Trunk Release 14 2.9 Valet Mode 14 3. Secondary Features 3.1 Remote Control Beep Mute 16 3.2 Siren 16 3.3 Passive Lock (Arm) 17 3.4 Safety Relock (Rearm) 17 3.5 Ignition Lock 18 3.6 Cold Start Timer 18 3.7 Turbo Timer 19 3.8 Option 1 Input 19 3.9 Remote Control Registration 20 3.10 Remote Start Registration 20 3.11 User Programmable Options 21 3.12 Time, Time Alarm, Timer Remote Start Reservation Set 22 3.13 Aux 1 Output 23 3.14 Aux 2 Output 23 3.15 Shock Sensor Option 23 3.16 Shock Sensor Sensitivity Adjustment 24 3.17 Z-Pass Touch 24 4. Factory Rese 5.Others 26 4. Warranty Card 27 4
1. INTRODUCTION 1.1 System Contents 1.2 Remote Control Button Layout 1.3 LCD Display Introduction 1.4 Remote Control Button Introduction 5
1.1 System Contents Main Control Module Remote Control Antenna Wiring Harness Z-PASS TOUCH Shock Sensor Manuals Siren 6
1.2 Remote Control Button Layout Front View Antenna OLCD / UCLCD Buttons Battery 1.5 V AAA Back View Lock / Unlock 2-way Remote & Main Controller Specifications - Please see the page 26 1.3 LCD Display Layout 7
1.4 Remote Control Button Introduction 8 CAUTION NEVER use the system except for its intended use. This is an electronic system with complex circuitry. Avoid dropping the components or cause any other physical damage as that will void the warranty.
LEGEND: “ - “ means to hold for 2 seconds - press and hold button(s) until 1st beep is heard from the remote control. “ ~ “ means to hold for 4 seconds - press and hold button(s) until 2nd beep are heard from the remote control. 9 Button(s) Duration* Description Ⅰ 0.5 sec Arm / Door Lock Ⅱ 0.5 sec Disarm / Door Unlock Ⅲ× 3 Times 0.5 sec Remote Control Hold ON/OFF Ⅳ 0.5 sec Vehicle Status / Car Finder Ⅰ - 2+ sec Panic Ⅲ- 2+ sec Remote Start Ⅳ - 2 sec Trunk Release Ⅱ ~ 4 sec Time / Alarm / Remote Start Timer Set Ⅰ + Ⅳ 0.5 sec Remote Control Beep Mute ON/OFF Ⅱ + Ⅲ 0.5 sec Siren Mute ON/OFF Ⅰ + Ⅱ 0.5 sec Aux 1 Ⅲ + Ⅳ 0.5 sec Aux 2
2. PRIMARY FEATURES 2.1 Arm (Door Lock) 2.2 Disarm (Door Unlock) 2.3 Arm / Disarm Status 2.4 Car Find & Status 2.5 LCD Screen Status 2.6 Panic 2.7 Remote Start 2.8 Trunk Release 2.9 Valet Mode 2.1 Door Lock (Arm) ButtonⅠ 0.5 sec 10
11 Successful Arm (Door Lock) Failed Arm (Door Lock) If a door, trunk and/or hood is open while arming, 4 siren chirps and 4 parking light flashes will occur immediately. Please ensure any doors, trunk and/or hood that is open, is closed. Rearm the system. 2.2 Door Unlock (Disarm) Button Ⅱ 0.5 sec Successful Disarm (Door Unlock) 2.3 Arm / Disarm Status Ⅱ 0.5 sec After the alarm is triggered, pressing Button II will stop the siren from sounding. The system is still armed at this point. Pressing Button II again will disarm the system. The LED’s on the Z-Pass module (while Discreet Mode is OFF) and the LED on the Antenna Module will indicate the status of the system. If a door is opened and closed, the Triggered Alarm status on the Z-Pass will be cleared. The siren duration can be programmed through the User Programmable Options Remote Control & flash. 1 beep will occur. Vehicle 1 parking light flash & 1 siren chirp Remote Control & will flash. 2 beeps will occur. Vehicle 2 parking light flashes & 2 siren chirps. 11 Status Z-Pass LED’s Armed Mode Normal Flash Disarmed Mode No Flash Triggered Alarm Fast Flash
2.4 Vehicle Status / Car Finder Button Ⅳ 0.5 sec Open Door Open Hood Open Trunk Remote Start On Shock Sensor Trigger Option 1 Input Trigger 2.5 Remote Control Hold ButtonⅢ 0.5 sec x 3 Times Pressing Button Ⅲ 3 times for 0.5 second each will put the remote control buttons into “Hold” mode. Any button presses will be ignored. To come out of “Hold” mode, press Button III 3 times for 0.5 second each again. Hold ON Hold OFF 2.6 Panic ButtonⅠ 2+ sec If there is a potential threat, you can alert those around you by using this feature. The siren will sound for 2 minutes and the parking lights will flash. Press either Button Ⅰ or Button Ⅱ to turn off panic mode. Remote Control 6 blinks & the vehicle’s inner temperature will be displayed. The following status indications will be checked and displayed. If the status is normal, only the temperature will be displayed. 4 beeps will occur. Vehicle 6 parking light flashes & 6 siren chirps 12
2.7 Remote Start ButtonⅢ 2+ sec Successful Remote Start Failed Remote Start If Button Ⅲ is pressed for 2+ seconds while remote start is on, remote start will turn off. The default remote start engine running time is 15 minutes. The time can be changed through the User Programmable Options. CAUTION: Do not use the remote start feature if the vehicle is in an enclosed area. Do not use the remote start feature where laws prevent its usage. Do not turn the key to the Start position or else damage may be done to the starter motor. Ensure that the parking brake (emergency brake) is always engaged. Do not use the remote start feature with convertible and/or open concept cars such as utility vehicles. 13 Remote Control & will blink until remote start is turned off. 1 beep will occur if the main control module communicates with the remote control. 5 beeps will occur after remote start is successful. Vehicle 1 parking light flash & 1 siren chirp if the main control module communicates with the remote control. 5 parking light flashes & 5 siren chirps after remote start is successful. Reason for Failure Vehicle Remote Control Key at ON Position 1 parking light flash & 1 siren chirp 3 beeps Open Door 3 parking light flashes & 3 siren chirps 3 beeps Open Hood and/or Trunk 4 parking light flashes & 4 siren chirps 3 beeps Failed Remote Start Reservation for Manual Transmission Vehicles 7 parking light flashes & 7 siren chirps 3 beeps
2.8 Trunk Release Button Ⅳ 2 sec Trunk release will unlock the door(s) and disarm the system. NOTE: On manual transmission vehicles, trunk release will turn off remote start. 2.9 Valet Mode ButtonsⅠ+ Ⅲ 4 sec Valet Mode ON Valet mode OFF Valet mode without remote control (Emergency shut off) 1. Insert the key into the key cylinder and turn to the ON position. 2. Within 3 seconds, press the foot brake 6 times. 3. On the 6th press, hold down the foot brake until 1 parking light flash and 1 siren chirp occur. NOTE: This feature can be used to turn off the alarm with the key if the system has been triggered. NOTE: Valet mode can only be turned off via the remote control. Remote Control & & will blink. 2 beeps will occur. Vehicle 2 x parking light flashes & 2 siren chirps Remote Control & 1 will blink. will stay ON. Vehicle 1 parking light flash & 1 siren chirp Remote Control & will blink. will turn OFF. Vehicle 2 parking light flashes & 2 siren chirps 14
3.SECONDARY FEATURES 3.1 Remote Control Beep Mute 3.2 Siren Mute 3.3 Passive Lock (Arm) 3.4 Safety Relock (Rearm) 3.5 Ignition Lock 3.6 Cold Start Timer 3.7 Turbo Timer 3.8 Option 1 Input 3.9 Remote Control Registration 3.10 Remote Start Reservation 3.11 User Programmable Options 3.12 Time, Time Alarm, Timer Remote Start Reservation Set 3.13 Aux 1 Output 3.14 Aux 2 Output 3.15 Shock Sensor Option 3.16 Shock Sensor Sensitivity Adjustment 3.17 Z-Pass Touch 15
3.1 Remote Control Beep Mute ButtonsⅠ+ Ⅳ 0.5 sec Remote Control Beep Mute ON - Vibrate ON When Remote Control Mute is ON, the remote control will use vibration alerts. Remote control mute OFF - Beeper ON 3.2 Siren Mute ButtonsⅡ+ Ⅲ 0.5 sec Siren Mute ON - Siren OFF No siren chirps will occur unless for alarm alerts (door trigger, hood trigger, trunk trigger, shock trigger, and/or Option 1 trigger) and panic mode. Siren Mute OFF - Siren ON Remote Control & will blink. will stay ON. Vehicle 1 parking light flash & 1 siren chirp Remote Control & will blink . will stay ON. Vehicle 1 parking light flash & 1 siren chirp Remote Control & will blink. will turn OFF. Vehicle 2 parking light flashes & 2 siren chirps 16
3.3 Passive Arm (Lock) ButtonsⅠ+Ⅱ 4 sec + Brake Pedal To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons I + II are pressed for 4 seconds. Once a door is opened and closed and the system is not armed via the remote control, the system will automatically arm and lock the doors. The system will arm and lock the doors after 25 seconds of the last door closing. Every 5 seconds, 1 parking light flash and 1 siren chirp will occur. On the 5th occurrence, the system will arm and the doors will lock. Passive Arm (Lock) ON Passive Arm (Lock) OFF 3.4 Safety Rearm (Relock) ButtonsⅡ+ Ⅲ 4 sec + Brake Pedal To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons II + III are pressed for 4 seconds. If the system is in the armed state and the system is disarmed but a door is not opened, the system will Safety Rearm automatically within 30 seconds. Safety Rearm (Relock) ON Safety Rearm (Relock) OFF Remote Control & will blink. will stay ON. Vehicle 1 parking light flash & 1 siren chirp Remote Control & will blink. will turn OFF. Vehicle 2 parking light flashes & 2 siren chirps Remote Control & will blink. will stay ON. Vehicle 1 parking light flash & 1 siren chirp Remote Control & will blink. will turn OFF. Vehicle 2 parking light flashes & 2 siren chirps 17
3.5 Ignition Lock ButtonsⅠ+ Ⅳ 4 sec To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons I + IV are pressed for 4 seconds. Ignition lock will lock the doors when the foot brake is pressed after the key is put into key cylinder and turned to the ON position. If a door is opened while the key is in the ON position, the doors will lock again once the door is closed and the foot brake is pressed again. Ignition Lock ON Ignition Lock OFF 3.6 Cold Start Timer ButtonsⅡ+ Ⅳ 4 sec To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons II+ IV are pressed for 4 seconds. Once Cold Start Timer I s turned ON, the vehicle will remote start automatically every 1, 2, or 3 hour(s) as specified by the User Programmable Options. If the vehicle is driven or remote start is turned ON, the timer will automatically restart once the engine is turned OFF. The timer can be set through the User Programmable Options. Cold start timer ON Cold start timer OFF Remote Control & will blink. will stay ON. Vehicle 1 parking light flash & 1 siren chirp Remote Control & will blink. will turn OFF. Vehicle 2 parking light flashes & 2 siren chirps Remote Control & will blink. will stay ON. Vehicle 1 parking light flash & 1 siren chirp Remote Control & will blink. will turn OFF. Vehicle 2 parking light flashes & 2 siren chirps 18
3.7 Turbo Timer ButtonsⅢ + Ⅳ 4 sec To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons III + IV are pressed for 4 seconds. This feature will allow turbocharged or supercharged vehicles to cool down by idling the engine for a specified amount of time even though the key is turn to the OFF position. The engine will continue to idle. Turbo Timer ON Turbo Timer OFF The duration for idling can be specified through the User Programmable Options. CAUTION: Please ensure that the vehicle is in Park (automatic transmission) or Neutral (manual transmission). Also, ensure that the parking brake (emergency brake) is engaged. Do not idle the vehicle in an enclosed area. Do not idle the vehicle if any laws prohibit this action. Do not idle the vehicle if it is a convertible or open concept type of vehicle. 3.8 Option 1 Input Additional sensors can be added to the system using Option 1 input. No additional programming is required. When the sensor is triggered, the parking lights will flash and the siren will sound. Remote Control & will blink. will stay ON. Vehicle 1 parking light flash & 1 siren chirp Remote Control & will blink. will stay OFF. Vehicle 2 parking light flash & 2 siren chirp 19
3.9 Remote Control Registration 1. Insert key and turn the key to ON position (engine is OFF). 2. Press brake pedal 4 times. 3. On the 4th press, hold the brake pedal down. 4. 3 parking light flashes and 3 siren chirps will confirm remote control programming mode. 5. Press Button Ⅰ (Lock Button) . 6. After each remote control is added, there will be a confirmation of 2 parking light flashes and 2 siren chirps. You can add up to 3 2-way remote controls and 2 1-way remote controls per system. 7. Once the key is turned to the OFF position or 10 seconds without adding a remote control passes, the system will exit remote control programming mode. ※ Each time a remote control is added, all remote controls must be reprogrammed to the system. Adding a remote control erases previously stored remote controls from the system. 3.10 Remote Start Reservation Manual transmission vehicles require remote start reservation in order to ensure that the vehicle is properly prepared for remote start. There are 2 remote start reservation modes: automatic and manual. Please note that automatic and manual do not refer to the transmission type. Rather, automatic and manual refer to the type of remote start reservation. 1. Automatic Remote Start Reservation (Default) a. Before turning off the engine, put the transmission into Neutral. Ensure that the parking brake (emergency brake) is engaged. Take foot off of the foot brake. b. Turn the key to the OFF position. The engine should still be running. c. Exit the vehicle within 2 minutes. d. Once the last door is closed, the engine will turn off. e. Arm the system. Remote start is ready to be used. 2. Manual Remote Start Reservation a. Before turning off the engine, put the transmission into Neutral. Ensure that the parking brake (emergency brake) is engaged. Take foot off the foot brake. b. Press Button Ⅲ for 2 seconds. c. Turn the key to the OFF position. The engine should still be running. d. Exit the vehicle within 2 minutes. e. Once the last door is closed, the engine will turn off. f. Arm the system. Remote start is ready to be used. NOTE1: Remote start reservation type can be changed through the User Programmable Options. NOTE2: If a door, trunk, or hood is opened, remote start reservation will be cancelled and remote start will not be available. 20
3.11 User Programmable Options Buttons Ⅲ + Ⅳ 2 sec When you enter programming mode by holding Buttons III + Ⅳ for 2 seconds, you will hear 1 remote control beep. The parking lights will flash 1 time and the siren will chirp 1 time. You are now in programming mode. Follow the chart below for programming options. For example, to select 5 minutes for Remote Start Run Time, hold Buttons III + Ⅳ for 2 seconds. You will hear 1 remote control beep, see 1 parking light flash, and hear 1 siren chirp. Within 5 seconds, press Button IV. You will hear 1 remote control beep to signify the first button press. Press Button I to enter the Remote Start Run Time menu. You will hear 2 remote control beeps to signify the second button press. Now, press Button Ⅱ to select 5 minutes. You will hear 3 remote control beeps to signify the third button press. You will also hear 1 chirp and see 1 parking light flash. User Option Options Ⅰ Ⅱ Ⅲ Remote Start Run Time Ⅳ → Ⅰ 15 min 5 min 25 min Diesel Warm Up Time Ⅳ → Ⅱ 30 sec 15 sec 7.5 sec Siren Sound Time Ⅳ → Ⅲ 30 sec 70 sec 100 sec Turbo Timer Run Time Ⅳ → Ⅳ 1 min 2 min 5 min Remote Start Reservation Ⅲ → Ⅳ Automatic Manual Cold Start Timer Ⅲ → Ⅲ 1 hour 2 hours 3 hours Button Sequence Shock Sensor ON/OFF Ⅲ → Ⅱ ON OFF Temperature Unit Ⅲ →Ⅰ Fahrenheit Celsius Default values. 21
3.12 Time, Alarm, Remote Start Timer Set ButtonⅡ4 sec The time, alarm, and remote start timer can be set by holding down Button I for 4 seconds. The following buttons are used. ButtonⅠ : Time Menu (Time → Alarm→ Remote Start Timer) Press and hold Button Ⅱ for 4 seconds. Once the time starts to blink, toggle to Alarm and Remote Start Time and back to Time by pressing Button I for 0.5 second at a time. ButtonⅡ : Hours setting. Press and/or hold Button II in order to increase the hours value. Button Ⅲ : Minutes setting. Press and/or hold Button III in order to increase the minutes value. Button Ⅳ: Confirmation or rejection. Press and hold Button IV for 2 seconds in order to accept the desired time or press for 0.5 second in order to reject the set time. NOTE : If a button is not pressed within 20 seconds of another press, programming mode will be exited. 1. Time - Clock Feature Displaying Current Time a. Press and hold Button Ⅱ for 4 seconds. The time will begin to blink. b. Press ButtonⅡ and Button Ⅲ in order to adjust the hours and minutes. c. Press and hold Button Ⅳ for 2 seconds in order to confirm the set time. 2. Alarm - Alarm Clock Feature a. Press and hold Button Ⅱ for 4 seconds. The time will begin to blink. b. Press Button I for 0.5 second to toggle to Alarm setting. c. Press ButtonⅡ and Button Ⅲ in order to adjust the hours and minutes. d. Press and hold Button Ⅳ for 2 seconds in order to confirm the set time. e. The icon will appear. 3. Remote Start Timer Set - Remote Start will occur at the specified time if all constraints on remote start are met. Remote Start will occur each day at the specified time until the feature is turned OFF. a. Press and hold Button Ⅱ for 4 seconds. The time will begin to blink. b. Press Button I twice for 0.5 second each to toggle to Remote Start Timer setting. c. Press ButtonⅡ and Button Ⅲ in order to adjust the hours and minutes. d. Press and hold Button Ⅳ for 2 seconds in order to confirm the set time. e. The icon will appear. 22
3.13 Aux 1 Output Buttons Ⅰ + Ⅱ 0.5 sec Aux 1 output can be used to control other devices such as window modules for rolling up or rolling down windows. Press Buttons Ⅲ + Ⅳ for 0.5 second to activate Aux 1 output. 2 parking light flashes and 2 siren chirps will confirm output. The remote control will blink 2 times and beep 2 times. 3.14 Aux 2 Output Buttons Ⅲ+ Ⅳ 0.5 sec Aux 2 output can be used to control other devices such as window modules for rolling up or rolling down windows. Press Buttons Ⅱ+ Ⅳ for 0.5 second to activate Aux 2 output. 2 parking light flashes and 2 siren chirps will confirm output. The remote control will blink 2 times and beep 2 times. 3.15 Shock Sensor 23 Warning shock sensitivity adjustment Full shock sensitivity adjustment Green LED indicator for warning shock Red LED indicator for full shock
3.16 Shock Sensor Sensitivity Adjustment The sensitivity of the shock sensor can be controlled by turning a dial on the shock sensor module. Turn the dial according to the amount of sensitivity that is desired. Keep in mind that turning the sensitivity to its maximum can result in false alarms 3.17 Z-Pass Touch The system can be armed or disarmed by “touching” the Z-Pass Touch with a PIN of 4 - 10 digits. 1. PIN Registration a. Turn Key to ON position (Engine OFF) b. Press ENTER until ALL OUTER LED’s light up. c. Enter 4 - 10 digit PIN. In order to toggle between “1 - 5” and “6 - 0”, press “SHIFT”. d. Once all of the numbers are entered, press ENTER until all LED’s blink 3 times. 2. System Arm/Disarm a. Press ENTER until ALL LED’s blink 1 time. b. Enter 4 - 10 digit PIN. c. Press ENTER until ALL LED’s blink 4 times. d. System will Arm or Disarm accordingly. 3. Driver Call a. Press DRIVER CALL 3 times while the system is in armed mode. b. All LED’s will blink quickly and 2 siren chirp / light flash will occur. Driver call will be sent to the 2-way remote control. 4. Discrete mode - Hold driver call button until outer LED’s blink once. - To turn off discrete mode, hold down driver call button until outer LED’s blink twice. Discrete mode can be done in armed or disarmed mode. Vehicle Full Shock Continuous parking light flash and siren sound. Remote Control Tune Warning Shock Beep 10 second parking light flash and siren sound. 24
Remote Control & will blink. The remote control will beep or vibrate. Vehicle Parking lights will flash and siren will sound. Remote Control & will blink. The remote control will beep or vibrate. Vehicle Parking lights will flash and siren will sound. Remote Control & will blink. The remote control will beep or vibrate. Vehicle Parking lights will flash and siren will sound. Remote Control & will blink. The remote control will beep or vibrate. Vehicle Parking lights will flash and siren will sound. Remote Control & will blink. The remote control will beep or vibrate. Vehicle Parking lights will flash and siren will sound. Remote Control & will blink. The remote control will beep or vibrate. Vehicle Parking lights will flash and siren will sound. Remote Control will blink. The remote control will beep every hour. Vehicle 4. Triggers The following triggers will occur ONLY when the system is armed. Shock Trigger Door Trigger Hood Trigger Trunk Trigger Alarm Trigger During Remote Start Option 1 Trigger Low Battery 25
26 WARRANTY CARD Use this warranty card for your records. Please go to www.zenesisalarms.com Visit the link above for specific warranty terms and conditions. ITU emission Code 8K50F1D Oscillation Type X-TAL Modulation Type FSK (Frequency shift keying) Data Rate (Mbps) 1200 bps Operated Frequency 433.920 ㎒ Channel Number One Channel Communication Type Simplex(Two-way) Operation temperature (-) 40℃ ~ (+) 80 ℃ Remote Controller: - 250 g / 66 (L) ㎜ x 30 (W) ㎜ x 15 (D) ㎜ Main Controller: 140 (L) ㎜ x 95 (W) ㎜ x 30 (D) ㎜ Power Source Remote Controller: 1.5 Vdc (Alkaline battery), Size: AAA Main controller:: 12Vdc (Use the Car Adaptor) Weight / Dimension
27

Navigation menu