Belkin F7D7602V1 NetCam HD User Manual

Belkin International, Inc. NetCam HD

User Manual

ORViewing through a browser Wall-MountAttach screws to wall and hang plate onto screws.1/8 in or 5.5mmAlign base with plate and screw on camera post.Download a complete manual at www.belkin.comWi-Fi® HD Camera with Night VisionQuick Install GuideWelcome to NetCam HD.2 3Unscrew camera post from the base and remove weight.From any computer, visit http://www.belkin.com/netcamEnter your user name and password created during setup.112NETCAM HDFCC StatementDECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin International, Inc., of 12045 E. Waterfront Drive, Playa Vista, CA 90094, declare under our sole responsibility that the device, F7D7602 V1, complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Exposure to Radio Frequency Radiation. The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized. When connecting an external antenna to the device, the antenna shall be placed in such a manner to minimize the potential for human contact during normal operation. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try and correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna. • Increase the distance between the equipment and the receiver. • Connect the equipment to an outlet on a circuit dierent from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.IMPORTANT NOTE: Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instructions as documented in this manual. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only.IMPORTANT NOTICE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 23cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC Statement: This Class B digital apparatus complies with Canadian ICES-003 Cet appareil numerique de la classe B conforme a la norme NMB-003 du CanadaIndustry Canada Statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Ce dispositif est conforme a la norme CNR- standards d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable.IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Déclaration d’exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.Avertissement:This radio transmitter (IC: 3623A-F7D7602V1/ Model: F7D7602V1) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de PCB dipole antenne avec dB [3.1]. Une antenne à gain plus élevé est strictement interdite par les règlements d’Industrie Canada. L’impédance d’antenne requise est de 50 ohms.Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peutfonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pourl’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectriqueà l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire àl’établissement d’une communication satisfaisante.Le présent émetteur radio (IC: 3623A-F7D7602V1/ Model: F7D7602V1) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.8820-01324 Rev.A00F7D7602v12.5mm Please set switch to .Wait a minute for a blinking amber from .Download Belkin NetCam app on your smartphone or tablet. If you have done so already and you’re adding additional cameras, begin at step 2.2Plug in NetCam HD.Belkin NetCam1Connect to NetCam HD Wi-Fi signal.34Launch NetCam app to complete setup.App Features:Tap camera name to view camera. Camera Status Icons:Online: Camera is available to share with multiple guests.Oline: Camera is manually disabled.Private: Camera is set to block all guests.An error occurred with the camera.Setup5After completing setup, set switch to . Tab to access your camera’s settings page. PR# 36397FILE NAME QIG_F7D7602_8820-01324_REVA00_NETCAMHDSKU# F7D7602v1P#/MKTG# 8820-01324 RevA00DESIGNER(S) LYNETTEDATE 1/24/13 VERSION 020.00 x 0.00 x 0.00Business Unit:Program Manager:Packaging Engineer:Date Drawn:Material:Blank Size:Side Shown:L x W x D (mm):DIE LAYOUT0Unit:Flute/Grain:REVIntermediatePRINT SIDE0.00 x 0.00 x 0.00L x W x D (in):FrontBack28[711.200]31/2[88.900]55/8[142.875]IN/MM3DDRAWING SCALE 1:1Retail Outside Dimension (Including Hang Tab)DO NOT PRINTDIE LINES, PRINTERS NOTESPRINT SPECS: DIE/MATERIAL SPECS:711.20 x 393.70711.20 x 393.70Die Line File:NET-NetworkingPushpak Jain28# Litho Paper11/8/2012IDL_F7D7602_HD NETCAM QIGColor Plates:Fonts: Notes:Artwork File:Branding Designer:Production Artist:horizontal00RELEASE DATE: 11/08/2012Tolerance:+/- 1/32" - 0.8mmFor product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou transmetteur.

Navigation menu