BTI Wireless DAS1900M40RUS 1.9GHz PCS Band 40W Remote Unit on BTI DAS system User Manual

Bravo Tech (Shenzhen) Co. Ltd. 1.9GHz PCS Band 40W Remote Unit on BTI DAS system Users Manual

UserManual.wiki >

DAS1900M40RUS User Manual

Users Manual

mBSC-H DAS System Installation Manual Issue 5 mBSC-H DAS SYSTEM INSTALLATION AND OPERATIONS MANUAL

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 2 COPYRIGHT This document serves as the System Installation Manual for the BTI mBSC-H Fiber Distributed Antenna System (DAS) system. BTI reserves the right to change the contents without prior notice. No part of this document may be reproduced or utilized. © 2009-2013, BTI, All Rights Reserved REVISION HISTORY ISSUE NO. DESCRIPTION DATE 1 INITIAL DRAFT OCT. 28, 2009 2 UPDATE SPECIFICATIONS JAN. 18, 2010 3 UPDATE SPECIFICATIONS, INSTALLATION, AND ILLUSTRATIONS MAY 31, 2011 4 UPDATE SPECIFICATION, INSTALLATION, MAINTENANCE, AND ILLUSTRATIONS FEB 22, 2012 5 UPDATE SPECIFICATION WITH THE LATEST MECHANICAL DESIGN AUG 31, 2013 6 ADD THE MESSAGE FOR FCC WARING LABEL ON PAGE 6 APR 28, 2014 7 Change the MPE Distance to 6 meters in page 6 JUN 10, 2014

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 3 Table of Contents 1 GENERAL INFORMATION ...................................................... 6 1.1 SAFETY PRECAUTIONS ............................................................................... 6 1.2 GLOSSARY AND ACRONYMS ...................................................................... 7 2 INTRODUCTION ...................................................................... 8 3 GENERAL DESCRIPTION ...................................................... 8 3.1 SYSTEM COMPONENTS DESCRIPTION ..................................................... 8 3.1.1 Host Unit ................................................................................................... 9 3.1.2 Network Management System ................................................................ 9 3.1.3 Remote Unit ............................................................................................ 11 3.2 USER INTERFACE ....................................................................................... 14 3.2.1 Host Unit Interface ................................................................................. 14 3.2.2 NMS Interface ......................................................................................... 14 3.2.3 Remote Unit Interface .......................................................................... 16 3.3 SPECIFICATIONS ........................................................................................ 18 3.3.1 Host Unit Specifications ........................................................................ 18 3.3.2 NMS Specifications .............................................................................. 18 3.3.3 Remote Unit Specification ................................................................... 19 4 INSTALLATION ...................................................................... 20 4.1 SYSTEM INSTALLATION OVERVIEW ........................................................ 20 4.2 REMOTE UNIT INSTALLATION ................................................................. 21 4.2.1 Remote Unit Installation Overview ....................................................... 21 4.2.2 Installation Hardware And Tools ........................................................... 21 4.2.3 Unpacking And Inspection .................................................................... 23 4.2.4 Mechanical Installation .......................................................................... 28 4.2.4.1 Mechanical Safety Precautions ....................................................................................... 28 4.2.4.2 Install The Mounting Panel .............................................................................................. 29 4.2.4.3 Install The Remote Unit On The Mounting Panel ............................................................ 30 4.2.4.4 Install The Shroud Cover ................................................................................................. 30 4.2.5 Electrical Installation ............................................................................. 32 4.2.5.1 Electrical Safety Precautions ........................................................................................... 32 4.2.5.2 Grounding ........................................................................................................................ 33 4.2.5.3 Route the Cables ............................................................................................................. 33 4.2.5.4 Fiber Optic Cable Connection ......................................................................................... 33 4.2.5.5 Antenna Cable Connection .............................................................................................. 34 4.2.5.6 AC Power Cable Connection ........................................................................................... 35 4.2.5.7 Slave Cable Connection .................................................................................................. 36 4.2.6 Remote Unit Installation Review ......................................................... 39

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 4 4.2.6.1 Mechanical Installation Review ....................................................................................... 39 4.2.6.2 Electrical Installation Review ........................................................................................... 39 4.2.6.3 Field Status Test - Remote Unit LED Status Indicators ................................................... 39 4.2.7 Troubleshooting ..................................................................................... 40 4.3 HOST UNIT INSTALLATION ........................................................................ 41 4.3.1 Host Unit Installation Overview ............................................................ 41 4.3.2 Installation Hardware And Tools ........................................................... 41 4.3.3 Unpacking And Inspection .................................................................... 42 4.3.4 Electrical Installation ............................................................................. 43 4.3.4.1 Electrical Safety Precautions ........................................................................................... 43 4.3.4.2 Grounding ........................................................................................................................ 44 4.3.4.3 DC Power Cable Connection ........................................................................................... 48 4.3.4.4 Install the BIU and FIU modules ...................................................................................... 49 4.3.4.5 Alarm Installation ............................................................................................................. 49 4.3.4.6 Connect the BIU/FIU Modules ......................................................................................... 51 4.3.4.7 Optional Equipment Installation ....................................................................................... 52 4.3.4.8 Connect POI to BIU ......................................................................................................... 53 4.3.4.9 Connect the Fiber Optic Cable ........................................................................................ 53 4.3.5 Host Unit Installation Review .............................................................. 53 4.3.5.1 Electrical Installation Review ........................................................................................... 53 4.3.6 Troubleshooting ..................................................................................... 55 4.4 NMS INSTALLATION ................................................................................... 56 4.4.1 Installation Overview ............................................................................. 56 4.4.2 Installation Hardware and Tools ........................................................... 56 4.4.3 Unpacking And Inspection .................................................................... 57 4.4.4 Verify Server software ........................................................................... 57 4.4.5 Initial System Setup ............................................................................... 58 4.4.5.1 CD-ROM Install ................................................................................................................ 58 4.4.5.2 Launch NMS .................................................................................................................... 59 4.4.6 Initial Start-up Configuration ................................................................. 60 4.4.6.1 Modify Default Accounts .................................................................................................. 62 4.4.6.2 Set-up New User Accounts .............................................................................................. 65 4.4.6.3 Configure Software Parameters ...................................................................................... 67 4.4.7 Firmware Update .................................................................................. 68 4.4.8 Software Upgrade Installation ............................................................... 69 4.4.8.1 CD-ROM Install ................................................................................................................ 69 4.4.9 NMS Upgrade Installation Review ....................................................... 70 4.4.10 Troubleshooting ................................................................................... 72 5 mBSC DAS SYSTEM START-UP .......................................... 73 5.1 SYSTEM COMMUNICATION ....................................................................... 73 5.1.1 Establishing a Host Unit communication ............................................ 73 5.2 INITIAL NETWORK CONFIGURATION ....................................................... 76

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 5 5.2.1 Add a Site ............................................................................................... 78 5.2.2 Add a Host Unit ...................................................................................... 80 5.2.3 Configuring the Host Unit Hardware Card ........................................... 82 5.2.4 Map the IP Address to the NMS Software ............................................ 86 5.2.5 Adding a Master and/or a Slave Remote Unit ...................................... 88 5.2.5.1 Adding a Remote Unit...................................................................................................... 88 5.2.5.2 Modifying or Deleting a Remote Unit ............................................................................... 91 5.2.6 Connect Host Unit to Server ................................................................. 92 5.3 MANAGING AND MONITORING ALARMS ................................................. 92 5.3.1 Alarm Manager ....................................................................................... 92 5.3.2 Configuring Standard Alarm Defaults .................................................. 93 5.3.3 System Activation Review ................................................................... 97 5.3.4 Troubleshooting ................................................................................... 98 6 Maintenance .......................................................................... 99 6.1 General ........................................................................................................ 99 6.2 Host Unit ...................................................................................................... 99 6.3 NMS 100 6.4 Remote Units ............................................................................................. 100 6.4.1 Fans....................................................................................................... 100 7 CUSTOMER SERVICE CONTACT INFORMATION ............ 101

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 6 1 GENERAL INFORMATION 1.1 SAFETY PRECAUTIONS Danger: Danger is used to indicate the presence of a hazard that will cause serious personal injury, death or substantial property damage if the hazard is not avoided. Warning: Warning is used to indicate the presence of a hazard that may cause serious personal injury, possible death or substantial property damage if the hazard is not avoided. Caution: Caution is used to indicate the presence of a hazard that will or may cause minor personal injury or substantial property damage if the hazard is not avoided. 1. For general safety, only appropriately qualified personnel familiar with all recommended and regulatory safety practices and installation methods may be allowed to work on this system. 2. All general and regional safety and installation regulations relating to high voltage installations, proper use of tools and recommended individual protective equipment must be obeyed. 3. Operating instructions must be kept accessible and available for all users. 4. The network provider is responsible for implementing protective measures to avoid the health hazards associated with radiation from the Unit antenna(s). 5. Warning: This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC License to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. Warning label messages will be also shown in online and point-of-sale marketing materials and on outside packaging of device 6. For US and Canadian installations: FCC RF exposure compliance requires the following antenna installation and device operation configurations be satisfied: A separation distance of at least 6 meters must be maintained between the antenna of this device and all persons. RF exposure compliance may need to be addressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of 1.1307(b)(3). Maximum permissible antenna gain is 17 dBi. 7. Access should be restricted to appropriately qualified personnel. 8. Operation of this Unit is restricted to the license holders of the respective frequency range. 9. Use of this equipment is only for the purpose specified by the manufacturer. Modifications or the use of any spare parts which are not provided by or recommended by the manufacturer are prohibited as this may cause fires, electric shock or other injuries or damage. 10. High temperatures due to power dissipation may occur, do not operate the equipment on or near combustible materials. 11. Ascertain that the mains supply is disconnected before opening the Unit as well as connecting or disconnecting the mains connector at the Remote Unit. 12. Observe ESD precautions. Use the available grounding system to connect ESD protection measures before commencing maintenance work.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 7 13. This Unit complies with European standard EN60950. 14. Verify that all regulatory requirements have been met and that all system settings have been set according to the intended use. (Please see appropriate manufacturer product information materials.) 15. Grounding the antenna cables close to the antenna connectors of the Remote Unit for protection against atmospheric discharge is highly suggested, even though the Remote Unit is internally protected against over-voltage. 16. Class 1 – Laser Radiation warning: Do not look into the beam, view it directly, or indirectly with or without optical instruments. 1.2 GLOSSARY AND ACRONYMS The acronyms and abbreviations used in this manual are detailed in the following list. Abbreviation Description AISG Antenna Interface Standard Group BIU Base station Interface Unit BTS Base Station CFR Crest Factor Reduction CL-OS Closed-Loop Operating System DAS Distributed Antenna System EDGE Enhanced Data for GSM Evolution FIU Fiber Interface Unit FIU-S Fiber Interface Unit - Simulcast FIU-NS Fiber Interface Unit - Non-Simulcast HPA High Power Amplifier HU Host Unit LMU Location Measurement Unit LNA Low Noise Amplifier mBSC Multi-Band Multi-System Multi-Carriers MIMO Multi-input multi-output MTBF Mean Time Between Failure NMS Network Management System PA Power Amplifier PCU Power Controller Unit PWM Pulse Width Modulation RCU Remote Control Unit RF Radio Frequency RU Remote Unit RX Receive Signal TDTD Time delay TX diversity TMA Tower Mounted Amplifier TX Transmit Signal UMTS Universal Mobile Telecom System VSWR Vertical Standing Wave Radio

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 8 2 INTRODUCTION This document provides the installation procedures for the BTI DAS system consisting of the DAS Host Unit, Remote Unit equipment and the Network Management System (NMS). It also provides for the initial configuration set-up, operation procedures and the software upgrade installation process for the Network Management System. For Host Unit and Remote Unit installation, the reader should be familiar with the use of Distributed Antenna Systems, power system distribution for both AC and DC, all safety guidelines and regulations, and the required tools to accomplish the installation in a safe manner. For NMS software installation and configuration as well as firmware update and software upgrade installations, the reader should be familiar with server administration, software install, firmware update, and software upgrade procedures at the administrator level. 3 GENERAL DESCRIPTION Figure 3-1. BTI DAS System The system consists of an Indoor HU (Host Unit) and an Outdoor RU (Remote Unit) and Network Management Software. 3.1 SYSTEM COMPONENTS DESCRIPTION The Host Unit is designed to be mounted in a 19” rack and should only be utilized in an indoor environment (0C - 45C) or in a place were an indoor-type environment can be provided. The NMS (Network Management System) runs on a centralized server that provides access to the entire network of hub sites and Remote nodes. The NMS is designed to configure, monitor, and manage all system functionality.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 9 The Remote Units may consist of combinations of 700MHz, 850MHz, 1900MHz and 2100MHz frequencies and are available in 20 Watt, 40 Watt or 80 Watt output configurations. Each RU is designed to support a Single Frequency Band. For multi-frequency use, the system can be configured as multiple Master/Slave Remote Units. Each Master Unit can support a maximum of two slave RUs with a maximum of three RUs supported per fiber connection. The primary transport between the HU and the RU is fiber optic. The Fiber Optic also provides the RU alarms and configuration communication between the NMS and the Remote Unit. The downlink and uplink optical signals are duplexed so only one fiber is required. 3.1.1 Host Unit The Host Unit provides a multiple slot assembly, consisting of 9 slots numbered from left to right: 1 through 9. Slots 7 through 9 are used and specifically keyed for the Remote Control Unit (RCU) and two redundant Power Supply Units (PSU) only. The Host Unit also houses the Base Station Interface Units (BIU) and Fiber Interface Units (FIU), Figure 3-2. The BIU comes in Diversity (BIU-D) and Non-Diversity (BIU-ND) and the FIU comes in Simulcast (FIU-S) and Non-Simulcast (FIU-NS) modules. The HU allows multiple combinations of BIU and FIU modules with up to 3 band downlink and uplink RF signals per BIU from the BTS and converts them to analog over RF for fiber transport. The Host Unit, through interface combinations, provides the following functions:  Converts the BTS RF signal to fiber signal.  Supplies connectivity between the BTS and the Remote Unit.  Manages and monitors the system alarms and configurations.  Supports 1 to 3 Sectors system configurations.  Supports a single sector with 1:1, 2:1, 3:1 and 4:1 Simulcast configuration.  Supplies fiber connectivity to the Remote Unit with in-band message signaling. Figure 3-2. Host Unit Multiple-Slot Assembly 3.1.2 Network Management System The Network Management System (NMS), shown in Figure 3-3, is a software-based Network Management System tool that provides control and monitoring functions for the BTI mBSC DAS system. NMS is used to provision and configure a new system for operation, set the system operating parameters, get system alarms and status messages, and update the system firmware. The Network Management System provides the following functions:  Manages SNMP v2 messaging to the Network Operating Center (NOC).  Provides a detailed graphic User Interface to manage, monitor and configure multiple DAS system.  Configure multiple DAS systems custom alarms.  Provides a firmware update interface.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 10 Figure 3-3. Network Management System Software Components Folder and Desktop Icon 3.1.3 Remote Unit The Single-Band Master Remote Unit, shown in Figure 3-4a, 3-4b, 3-4c and 3-4d, consists of an optical module (O/E), a downlink power amplifier, an LNA, and duplexer. The Optical module converts the downlink optical signal from the FIU module in the HU and splits the RF signal into 3 RUs. It also converts the uplink RF signal to an optical signal and simultaneously sends it to the FIU module in the HU for distribution to the BIU modules. Each optical module can support 3 RUs in any combination of different bands. The Single-Band Master Remote Unit provides the following functions:  Converts the forward optic signal to RF signal.  Boosts the forward RF signal from the HU to a higher power level (max output: 80W).  Amplifies the uplink signal from the antenna to improve the system receive sensitivity.  Supplies in-band messaging between the HU and RU for RU Alarms and configuration. The Remote Unit has been designed for minimal maintenance. Maintenance recommendations include a once yearly inspection and cleaning, if needed. A fan alarm will be generated should the fan current drop below one third of its required current.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 11 Figure 3-4a. 20 Watt and 40 Watt Fan Cooled Remote Unit Figure 3-4b. 80 Watt Fan Cooled Remote Unit

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 12 3.2 USER INTERFACE The user interface for each segment of the mBSC DAS System is designed to provide the most efficient interaction, installation and ease of use for the user. 3.2.1 Host Unit Interface Each interface module of the Host Unit, shown in Figure 3-5, is described in Table 3-1 below. Figure 3-5. Host Unit Interface Table 3-1. Host Unit User Interface Module Name Port Name Description Remark FIU-S/FIU-NS TX1, TX2 Downlink interface ports to be connected to BIU output RF signal RX1, RX2 Uplink interface ports to be connected to BIU input RF signal Fiber 1, Fiber 2 Fiber optic interface ports to be connected to the RU Optical signal E9111, E9111-2 The RX coupling uplink signal for LMU (TDOA location only) RF signal E9111, E9111-2 The RX coupling uplink signal for LMU (TDOA Location only) RF signal E9111, E9111-2 The RX coupling uplink signal for LMU (TDOA Location only) RF signal BIU-ND/BIU-D TX1, TX2, TX3, TX4 Input signals from the BTS to provide the combined downlink signal to FIUs RF signal RX1, RX2, RX3, RX4 The combined uplink signal from FIUs RF signal TX1 and TX2 out Downlink RF interface to FIU RF signal RX1, RX2, RX3, and RX4 out Uplink RF interface from the FIU RF signal 3.2.2 NMS Interface A simple login access, Figure 3-6, allows for quick access. A graphical user interface, Figure 3-7, provides real time user access to the configuration, performance monitoring, and alarm status. The system also

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 13 uses SNMPv2.0 protocol to transmit automated traps to the operator's Network Operations Center for remote alarming and system queries. These two capabilities provide for centralized configuration and alarm monitoring of the entire system. Operational parameters, such as uplink and downlink, and gain can be set through the NMS server. Status information at each node is easily available. The customer can readily access power output, ALC status, VSWR, PA temperature, and other basic operating parameters, The BTI NMS simplifies the configuration of the network by providing accurate downlink power and uplink gain updates. This allows the system operator to maximize the efficient use of field personnel when diagnosing system performance issues. Figure 3-6. NMS Login Interface

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 14 Figure 3-7. NMS Command Console Table 3-2. Default Parameter Values Menu Parameter Name Default Value System Parameter SNMP No User Manager Name: Manager; Password: 1; Level: Supervisor User User Name: User; Password: 1; Level: Observer 3.2.3 Remote Unit Interface The interface of the Remote Unit consists of connectors and LEDs that are located on the bottom of the RU enclosure. The Master RU user interface points are indicated in Figure 3-8 and Table 3-3. The Slave RU user interface points are indicated in Figure 3-9 and Table 3-4. Remote Units are classified as either MASTER or SLAVE. Master and Slave Units have exactly the same mechanical dimensions. Functionality is the main difference as the MASTER Remote Unit has the connection for the fiber optic cable. For supporting multiple bands, only the MASTER Remote Unit needs to have the fiber optic connection with the Host Unit. Other Remote Units are interfaced with SLAVE ports for receiving RF downlink signal and sending RF uplink signal with the Master Remote Unit.  MASTER Remote Unit:  Has the Fiber Optic Cable connection with the Host Unit  Provides the RF downlink signal to the SLAVE Remote Unit through “TX_IN” or “TX_OUT” port.  Receives the RF uplink signal from the SLAVE Remote Unit “RF_IN” or “RF_OUT” port.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 15  SLAVE Remote Unit:  No Fiber Optic Cable connection with the Host Unit  Interfaces with the Master Unit for downlink and uplink signal  Unused ports (TX_OUT, RX_IN) are blocked with a cover. Figure 3-8. User Interface of MASTER Remote Unit Table -3-3. Master Remote Unit User Interface Label Name Description ANT Interface port for Antenna Feed line OPERATE LED indicator for normal or critical fault status of the RU. Normal: Green ON, Critical fault: Red ON TX_Out RF output port to provide the input signal to the Slave Remote Unit when Dual or Triple Band application is configured. RX_In RF input port to provide the output signal to the Master Remote Unit when Dual or Triple Band application is configured. FIBER Fiber Optic Cable interface port for combined downlink and uplink signal POWER Interface port for the AC 110/220V power cable DC_FAN Provides power to the fan VENT Port for the balance of pressure inside and outside of the enclosure Figure 3-9. User Interface of SLAVE Remote Unit Table -3-4. Slave Remote Unit User Interface Label Name Description ANT Interface port for Antenna Feed line OPERATE LED indicator for normal or critical fault status of the RU. Normal: Green ON, Critical fault: Red ON

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 16 TX_Out (Slave 1) RF output port to provide the input signal to the Slave Remote Unit when Dual or Triple Band application is configured RX_In (Slave 2) RF input port to provide the output signal to the Master Remote Unit when Dual or Triple Band application is configured. POWER Interface port for the AC 110/220V power cable DC_FAN Provides power to fan VENT Port for the balance of pressure inside and outside of the enclosure 3.3 SPECIFICATIONS 3.3.1 Host Unit Specifications The specifications for the Host Unit of the mBSC DAS system are listed in Table 3-5: Table 3-5. Host Unit Specifications Host Unit Specification Description Notes System Support Multi-Frequency bands with Multi-Air Interface standards (GSM / EDGE / CDMA / WCDMA / AWS / LTE) Max No. of Plug-in module • 3 fixed slots for two (PSU) and a single (RCU) • 6 module slots for BIU and FIU PSU (Power Supply Unit) • -48Vdc and optional AC 110/220 DC converter • 2 PSU are installed for redundancy RCU (Remote Controller Unit) Main process board for DAS system BIU (Base station Interface Unit) • Support multi-frequency bands DL and UL interface • Support RX Diversity • QMA connector for RF Interface • Support 4 downlink and uplink interface ports FIU (Fiber Interface Unit) • Support 2 Fiber ports per FIU • Support Non-Simulcast or Simulcast 3.3.2 NMS Specifications The specifications for the Network Management System (NMS) of the mBSC system are listed in Table 3-6. Table 3-6. NMS Specifications NMS Specification Specification Notes Max No. of Nodes 1080 A combination of BIU, FIU and Remote Units SNMP based management Yes Real time alarm display Yes Display various system level values Yes Voltages, RF power, etc. Remote firmware download Yes Firmware update interface for DAS components. The NMS also requires a dedicated server to connect to the RCU. The Server specifications are Table 3-7. Server Specifications Server Specification Specification Notes Processor One Quad-core Intel® Xeon® 3400 series processor

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 17 Server Specification Specification Notes Operating System Microsoft® Windows® XP Professional Memory 4GB (4 DIMM slots) DDR3 Storage Cabled Hard Drive Options: 2.5" SATA SSD, SAS (10K), nearline SAS (7.2K) Maximum Internal Storage: 250G Power Single cabled power supply (250W) Video Card Matrox G200eW w/ 8MB memory Network Controller One dual-port Broadcom BCM 5716 3.3.3 Remote Unit Specification The specifications for the Remote Unit of the mBSC system are listed in Table 3-8. Table 3-8. Remote Unit Specifications System Specification Downlink Uplink Optic Wavelength 1310/1550nm Antenna Port 7/16 DIN female Optical connector E2000 Power Supply AC 110V / 220V ± 20% Current < 1A @ Full power, ~220V AC input < 2A @ Full power, ~110V AC input Weight varies per type Waterproof IP65

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 18 4 INSTALLATION 4.1 SYSTEM INSTALLATION OVERVIEW This section provides instructions for installing the mBSC DAS system in an efficient, productive and customer friendly order. Each component of the mBSC DAS system is covered in its own installation section as follows: 4.2.REMOTE UNIT INSTALLATION The Remote Unit installation section provides instructions for the mechanical and electrical installation of the mBSC Remote Unit including: mounting the Remote Unit, connecting the fiber optics cables; Antenna feed line; and AC power cables. The procedures in this section assume that the required Fiber Optic cables have been routed between the Host Unit and the Single-Band RU and that the required antenna has been installed. 4.3.HOST UNIT INSTALLATION The Host Unit installation section provides instructions for the electrical installation of the mBSC Host Unit including verifying the DC power cable connection, connecting the network cable, the alarm connectors, and other required connections and cables. The procedures in this section assume that the Host Unit has been inspected, the Remote Unit(s) installation is complete and that a dedicated IP address for the Host Unit has been designated. 4.4.NMS INSTALLATION The Network Management System (NMS) installation section provides instructions for setting up the pre-installed software component of the mBSC NMS. The instructions will allow a qualified user to install the NMS software, set-up accounts, change passwords for security, and upgrade the system software and hardware. The procedures in this section assume that the NMS server has been received, the Host Unit is installed, and that security software has been installed on the designated NMS computer(s).

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 19 4.2 REMOTE UNIT INSTALLATION Danger: Wet conditions increase the potential for receiving an electrical shock when installing or using electrical power equipment. To avoid electrical shock, never install or use the electrical equipment in a wet location. Danger: Do not look into the end of the fiber optic cables. Exposure to laser radiation may result. Do not assume that the laser power is turned off or that the fiber optic cable is disconnected at the other end. Danger: Use extreme caution when working with high voltage AC power. Ensure all power is disconnected before working on power circuit. Caution: Always make sure there is sufficient cable length to permit the routing of the fiber optic cables to prevent the cable damage. The optic cables may be damaged if bent or coiled too tightly. 4.2.1 Remote Unit Installation Overview The installation of the Remote Unit, both single enclosure and multi-enclosure, consists of the following steps: Table 4-1. Remote Unit Installation Overview Step Operation Type Operation Action 1 MECHANICAL INSTALL THE RU MOUNTING PANEL TO THE TOWER 2 MECHANICAL VERIFY THAT THE SIDE MOUNTING BRACKETS ARE SECURELY ATTACHED TO THE REMOTE UNIT 3 MECHANICAL INSTALL THE MASTER REMOTE UNIT ON THE MOUNTING PANEL 4 MECHANICAL MOUNT THE SHROUD COVER OVER THE ENCLOSURE AND SECURE IT 5 INSTALLATION REVIEW CONFIRM THE MECHANICAL INSTALLATION USING TABLE 4-4 MECHANICAL INSTALLATION CHECKLIST 6 ELECTRICAL GROUND THE UNIT 7 ELECTRICAL ROUTE THE CABLES TO BE CONNECTED 8 ELECTRICAL CONNECT THE FIBER OPTIC CABLES 9 ELECTRICAL CONNECT THE ANTENNA FEED LINE 10 ELECTRICAL INSTALL THE AC POWER CABLE 11 ELECTRICAL CONNECT ANY SLAVE REMOTE UNIT TO THE MASTER REMOTE UNIT 12 INSTALLATION REVIEW CONFIRM THE ELECTRICAL INSTALLATION USING TABLE 4-5 ELECTRICAL INSTALLATION CHECKLIST 13 FIELD STATUS TEST CHECK THE REMOTE UNIT LED STATUS INDICATORS USING TABLE 4-6 RU LED STATUS INDICATOR AND THE TROUBLESHOOTING GUIDE 4.2.2 Installation Hardware And Tools The Remote Units are shipped with the standard mounting hardware required for a BTI pole-mount

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 20 installation. Table 4-2 lists the mounting hardware provided by the manufacturer for a standard BTI pole mount installation kit. Additional hardware may be needed, depending on the site requirements, and may be ordered through Customer Service (Section 6). Table 4-2. Single-Band RU Mounting Hardware and Fasteners for a standard BTI pole mount installation kit Hardware and Fasteners Quantity Rec'd MOUNTING PANEL (Configurable) 1 I-BEAM or U-BEAM/CHANNEL MOUNTING BRACKETS 2 SHROUD COVER 1 M5 SCREW 8 M5 LOCK WASHER 8 M5 FLAT WASHER 8 M6 SCREW 8 M6 LOCK WASHER 8 M6 FLAT WASHER 8 M8 SCREW 8 M8 LOCK WASHER 8 M8 FLAT WASHER 8 M12 SCREW 4 M12 LOCK WASHER 4 M12 FLAT WASHER 4 JUNCTION BOX 1 RF CABLE (Designated Slave Unit) 2 FIBER OPTIC COWL 1 POWER CABLE (10 FEET) 1 FAN CONNECTOR (OPTIONAL) 1 Table 4-3. Specified Hardware Torque Type Screws Hex Nuts Spacers Spring/Lock Washers Spacers Flat Washers Thread M5 M8 M12 M5 M8 M12 M5 M8 M12 Specified Torques (lb. - ft.) 2 12 40 2 12 40 2 12 40 The following is a list of tools and any additional materials required for mounting every Single-Band Remote Unit configuration:  DIN male connectors  Tool kit for attaching DIN connectors to coaxial cable  Tools for installing exterior AC circuit  Tools for securing M5 screw

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 21  Wire cutters  Wire Stripper  Open End Wrench 1.25 inch/33mm (used for DIN connector)  Hex Wrench 5mm (M6 screw)  SAE Wrench 5/16 inch/8mm (the Slave Remote Unit connectors) 4.2.3 Unpacking And Inspection This section provides the instruction for receiving the equipment shipment, verifying all parts have been received and checking that no damage has occurred during transportation. The Remote Unit includes the following items:  Remote Unit(s)  Hardware and Fasteners described in Table 4-2, Section 4.2.2 Use the following procedure to unpack and inspect the Remote Unit and accessories: 1. Open the shipping container, Figure 4-1 and carefully remove any accessories from the protective packing material, Figure 4-2. Figure 4-1. Open the Shipping Container Figure 4-2. Remove Accessories 2. Remove the Shroud from the Remote Units(s), Figure 4-3. Figure 4-3. Remove the Shroud

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 22 3. Begin removing the Remote Unit(s) from the Mounting Panel by unscrewing the two (2) M8 fasteners at the bottom bracket Interface end of the Remote Unit(s), Figure 4-4. Figure 4-4. Remove the two M8 Fasteners 4. Remove the single (1) M8 fastener from the top bracket Fan end of the Remote Units and then remove the two (2) M5 fasteners from the metal shipping bracket and discard the metal shipping bracket, Figure 4-5. Figure 4-5. Remove the M8 Fastener and the two M5 Fasteners 5. Remove the Remote Unit(s) from the shipping crate. 6. Unpack the Mounting Panel from the crate.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 23 7. Verify receipt of hardware and fasteners using Table 4-2 8. Check each Remote Unit and accessories for broken or missing parts. If there is any damage or missing parts, contact BTI (Section 6) for an RMA and to reorder parts, if any replacement parts are required. NOTE: Check particularly for any damage to the power connection, the fins/fans, and the fiber optic cable connection on the Remote Unit Interface.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 24 4.2.4 Mechanical Installation 4.2.4.1 Mechanical Safety Precautions Please read the general Safety Precautions contained in Section 1.2 Safety Precautions 1. Follow the procedures provided by the manufacturer when installing the Remote Unit. Do not install the Unit in a place or in a manner that does not meet the manufacturer's provided specifications. 2. Use the mounting hardware supplied by the manufacturer. If non-standard mounting hardware is used, it must meet the requirements for mounting the Unit as specified by the manufacturer. NOTE: It is important that specified load limits for the Unit are not exceeded as this may void the warranty. 3. Safety measures for lifting heavy materials should be followed to prevent injury. 4. High temperatures may occur due to power dissipation. Please follow the specifications for proper Remote Unit ventilation as indicated by the manufacturer. 5. Check that the mains supply is disconnected, before connecting or disconnecting the main power connector at the Remote Unit. 6. Do not block airflow ventilation outlets during installation or Remote Unit(s) may sustain critical damage.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 25 4.2.4.2 Install The Mounting Panel Use the following procedure to install the mounting panel on the pole: 1. Take one M12 screw and insert it loosely in one of the two top holes in the panel. Place the mounting panel against the pole as shown in Figure 4-6. 2. Place one of the two I-Beam or U-Beam brackets on the back side of the pole so that it aligns with the M12 screw. 3. Hand tighten the screw to hold it in place 4. Place the second M12 screw in the next hole at the top of the panel and loosely fasten the screw as well. Continue until all four screws are in place as shown in Figure 4-7. 5. Use a wrench to securely fasten the screws through both panel and brackets until the panel is securely attached to the pole. Figure 4-6. Attach the Mounting Panel and Bracket to a Pole

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 26 Figure 4-7. The Mounting Panel secured tightly to a Pole 4.2.4.3 Install The Remote Unit On The Mounting Panel Use the following procedure to install the RU on the mounting Panel. 1. Verify that the attached side mounting brackets, as shown in Figure 4-8 are secure. 2. Grasp the Remote Unit at the top and bottom of the casing and carefully slide the top two hooks onto the mounting panel, Figure 4-9, followed by the lower hooks and allow the Unit to slide down into place. 3. After hanging the enclosure on the mounting panel, use the M8 screws, lock and flat washers to secure the rear mounting bracket (top and bottom) so the RU does not move. Figure 4-8. The Side Mounting Bracket to the Mounting Panel

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 27 Figure 4-9. Secure Enclosure To the Side Mounting Bracket 4.2.4.4 Install The Shroud Cover The Remote Unit has a Shroud cover for thermal protection. Use the following procedure to install the Shroud cover on the enclosure: 1. Line up the slots at the top of the Shroud cover to the tabs at the top of the mounting panel as shown in Figure 4-10. 2. Gently lower the slots over the tabs and slide the cover down. The cover will be at an angle, Figure 4-11. 3. Lay the cover flush against the mounting bracket, then carefully, place the M5 screw through the middle hole, aligning it to the hole on the bracket. Loosely fasten the screw. Working on the opposite side, again place an M5 screw through the middle hole and loosely fasten the screw. 4. Loosely fasten the remaining M5 screws to all four corners of the cover and then tighten all the screws securely.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 28 Figure 4-10. Install the Shroud Cover to the RU Figure 4-11. Secure Shroud Cover to the mounting panel

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 29 4.2.5 Electrical Installation 4.2.5.1 Electrical Safety Precautions Please read the general Safety Precautions presented in Section 1.2 Safety Precautions 1. This Unit uses high voltages. Follow the instructions for installation provided in this manual to prevent serious accidents including loss of life, severe personal injury or extensive property damage. 2. The Unit must be grounded before connecting any power supply. Grounding is a required precautionary measure. Grounding instructions are provided and should be followed for safety. 3. The Unit is internally protected against over-voltage, but in areas with strong and frequent lightning strikes additional lightning protection is strongly recommended. Grounding the antenna cables close to the antenna connectors will help prevent damage from atmospheric discharge. 4. Verify that there is a suitable circuit breaker and an over-current limiting device connected between the mains and the Remote Unit. 5. Check that the mains supply is disconnected, before connecting or disconnecting the main power connector at the Remote Unit. 6. An easily reached emergency disconnect device should be provided in the mains circuit if the power feeds to the Remote Unit(s) are not within close reach. 7. The Remote Unit should be installed in close proximity to a power source with a circuit breaker to ensure safe installation and for ease of power connectivity. 8. Electrical and electronic components can be destroyed by incorrectly wired connections. 9. Cable connector materials must meet manufacturer specifications to avoid corrosion at the connectors. 10. Check cable connections to ensure that water cannot penetrate the Unit. 11. Caution should be used when attaching the antenna. Hand tightening should be sufficient for connecting the antenna during installation. Manufacturer's recommendation for torque specification should be used during installation. Use the appropriate tool to complete the Antenna installation, but do not use tools, such as pliers, as they may cause damage to the Remote Unit. 12. A voltage limiting device is strongly recommended for electrical networks that often produce spikes. 13. Compliance with the surge requirement of EN 61000-4-5 (fine protection) has been met by this Unit. Installing additional external surge protection, depending on the individual application, via local supply connection and/or coarse protection is recommended to avoid damage caused by electrical surges.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 30 4.2.5.2 Grounding The Unit must be grounded and the integrity of the protective earth must be ensured. Connect an earth-bonding cable to the provided grounding connection on the equipment. Do not connect any additional external devices to the grounding connection. Figure 4-12. Grounding Connection 1. Uncover the RU interface by removing the Vandalism Protective Shield from the bottom of the Shroud Cover. 2. Loosen the hex nut located on the grounding connection as shown in Figure 4-12. 3. Connect the earth-bonding cable between the two lock and flat washers. 4. Tighten the hex nut, making sure the cable is securely connected before moving to the next phase of the installation. 4.2.5.3 Route the Cables Prepare and route all cables according to standard field installation procedures. The mains cable and mains plug is used as a disconnect device. For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be easily accessible. Care should be taken to prevent wear or field damage to cables during install. Particular attention should be paid to the Fiber Optics Cable as damage may occur if cable is tightly coiled or bent. The remote unit is connected to a external antenna or dish, and the antenna ports (mounted on the rear side of the EUT) is considered a Cable Distribution System circuit (CDS). Circuits for connection to the CDS are classified as TNV-1. 4.2.5.4 Fiber Optic Cable Connection One fiber optic cable must be routed from an external splice enclosure or fiber access terminal to the Master Remote Unit enclosure. The RU is equipped so only one cable is required per Master Remote Unit for the optic port. A hardened optical E2000 connector is used for the optic port.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 31 Warning: Do not look into the end of the fiber optic cable. Do not look directly into the optical transmitter of any Unit or exposure to laser radiation may result. An optical power meter should be used to check the active fibers. Use the following procedure to connect the fiber optic cable: 1. Connect or splice the drop Fiber cable to the outside plant cable. Verify that there is sufficient cable length to reach from the splice enclosure or fiber access terminal (not provided) to the bottom of the Master Remote Unit 2. Route the free end of the drop cable to the enclosure through the junction box as shown in Figure 4-13. 3. Leave sufficient slack to allow the cable to be connected and disconnected from the enclosure fiber optic port without bending or crimping the fiber optic cable. 4. Remove the cap from the interface port labeled "FIBER". Connect the fiber optic cable to the port on the bottom of the enclosure. Figure 4-13. Junction Box 4.2.5.5 Antenna Cable Connection The antenna feed line(s) must be routed from the antenna to each Remote Unit. The cable must have the appropriate antenna connector termination to connect to the RU antenna port (ANT), shown in Figure 4-14. Figure 4-14. Antenna port Use the following procedure to install the antenna cable:

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 32 NOTE: When using multiple RU enclosures to support more than one RF band, each RU is supporting a different frequency. When routing the coaxial antenna cable, it is critical that the appropriate frequency band cable be connected to the same frequency type RU. 1. Remove the dust cap from the DIN female connector located on the bottom of the enclosure. The port is labeled with “ANT”. 2. Route the coaxial antenna cables from the antenna to the bottom of the enclosures. 3. Cut the antenna cable to the required length and terminate with the appropriate connector. 4. Connect the antenna cable to the antenna port labeled with “ANT”, Figure 4-15. Figure 4-15. DIN Female Connector 4.2.5.6 AC Power Cable Connection Danger: Use extreme caution when working with high voltage AC power. Ensure all power is disconnected before working on power circuit. Warning: Verify that the Unit has been ground with an earth-bonding cable to the grounding connector. Use the following procedure to install the AC Power cable: 1. Route the power cable between the AC power port, located on the bottom of the enclosure and the nearest AC power junction box as shown Figure 4-16.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 33 Figure 4-16. Junction Box AC Power Cable Routing 2. Secure the cable between the AC power port and the AC power junction box. Leave sufficient slack in the cable to allow it to be easily connected and disconnected from the AC power port. 3. Install any AC power supply wires that may be required between the AC junction box and the AC circuit breaker box. 4. At the AC circuit breaker box, connect the AC power supply load wire to the circuit breaker. 5. Place the circuit breaker in the ON position and then test the connected end of the AC power cable for proper voltage levels and correct polarity. 6. When testing is complete, PLACE THE CIRCUIT BREAKER IN THE OFF POSITION. Danger: To avoid serious personal injury and equipment damage, always turn the AC power off on the circuit breaker before connecting the any power cable to the AC power port. 7. Connect the power cable connector to the AC power port labeled “POWER”. 8. Tighten the coupling nut. 4.2.5.7 Slave Cable Connection When two RU or more enclosures are installed for supporting multi-band. One is designated the Master Remote Unit and each additional RU, up to two Units, are designated as slave Remote Units. The Master and slave Unit(s) is specified by the frequency band. The Master Unit will separate the bi-directional signal related to the frequency and provide the RF input signal to each slave Remote Unit. The connection between Master and Slave is interfaced with the RF cable provided with the Remote Units. Use the following procedure to install the antenna cable:  All designated slave RUs arrive with two RF cables.  Connect one RF cable to the port labeled “TX_OUT” on the MASTER Remote Unit User Interface.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 34  Connect the other end of the RF cable to the port labeled “TX_IN” on the SLAVE Remote Unit User Interface as shown in Figure 4-17.  Connect the second cable to the port labeled "RX_IN" on the MASTER RU.  Connect the other end of the second RF cable to the port labeled "RX_OUT on the SLAVE RU. Figure 4-17. RF cable connection between Master and Slave Remote Unit 1 Slave to Slave Connection: Connect an RF cable into the port labeled "TX_OUT" on the first SLAVE RU User interface. 2 Connect the other end of the RF cable to the port labeled "TX_IN" on the next SLAVE RU Unit. Continue connecting all SLAVE RUs in this manner, as shown in Figure 4-18. 3 Connect an RF cable into the port labeled "RX_OUT" on the first SLAVE RU. 4 Connect the other end of the RF cable to the port labeled "RX_IN" on the next SLAVE RU. Continue connecting all SLAVE RUs in this manner. 5 Power may now be applied to all Master and Slave Units used in this configuration.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 35 Figure 4-18. RF cable connection between Slave to Slave Remote Units

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 36 4.2.6 Remote Unit Installation Review Use the following steps listed in Tables 4-3 and 4-4 to review the installation completion status 4.2.6.1 Mechanical Installation Review Table 4-4. Remote Unit Mechanical Installation Check Lists Items Description 1 Confirm that the Unit is mounted firmly and is stable. 2 Verify that the Unit is affixed per manufacturer's specifications. 3 Check that all screws and nuts are secure, that spring washers sit flush upon the flat washers, and that there are no missing flat washers and spring washers. 4 Examine each part and cable for breakage or damage. 5 Make sure the Unit is clean and free of dust and other contaminants 4.2.6.2 Electrical Installation Review Table 4-5. Remote Unit Electrical Installation Check List Items Description 1 Verify that the grounding cable is secure. 2 Make sure that all the cable sheathings are not damaged. 3 Confirm that the connection to the cables are stable and are not loose or damaged. 4 Check that the cables are completely connected, but make sure there is enough slack, if needed. Do not cross the cables and the cables should be bundled together in the same direction. 5 Check that the connected cables are not bent more than the manufacturer's specified maximum bending radius. 4.2.6.3 Field Status Test - Remote Unit LED Status Indicators Perform a visual review of the LED Status indicators on the installed Remote Unit. The Remote Unit (RU) status LED consists of a bi-colored LED of RED and GREEN. The high intensity LED is viewable from ground level under most circumstances when using the BTI RU shroud system. Table 4-6. Remote Unit LED Status Indicators LED Indicator Colors Cycles Test the LED Red and Green Blink 1 flash per second Master RU Fiber Alarm Red Fast Blink 2 times per second mRU and sRU Comm Fail Red and Green Blink 1 time per second PA/LNA shutdown or Other Red Fast Blink 2 times per second Normal Operation Green Blink 1 times per second

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 37 4.2.7 Troubleshooting

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 38

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 39 4.3 HOST UNIT INSTALLATION Danger: Wet conditions increase the potential for receiving an electrical shock when installing or using electrical power equipment. To avoid electrical shock, never install or use the electrical equipment in a wet location. Warning: Verify that the Unit has been ground with an earth-bonding cable to the grounding connector. 4.3.1 Host Unit Installation Overview The installation of the Host Unit consists of the following steps: Table 4-6. Host Unit Installation Overview Step Operation Type Operation Action 1 ELECTRICAL VERIFY THAT THE UNIT IS GROUNDED 2 ELECTRICAL CONFIRM THAT THE DC POWER CABLE IS INSTALLED AND SECURE 3 ELECTRICAL INSTALL THE BIU AND FIU MODULES 4 ELECTRICAL INSTALL THE ALARM CONNECTORS (Optional) 5 ELECTRICAL CONNECT THE BIU AND FIU 6 ELECTRICAL CONFIRM THAT THE POI AND FAN (Opt. Equip.) ARE CONNECTED 7 ELECTRICAL CONNECT OPTIONAL EQUIPMENT TO THE BIU (if present) 8 ELECTRICAL CONNECT THE FIBER OPTIC CABLES 9 INSTALLATION REVIEW CONFIRM THE ELECTRICAL INSTALLATION, TABLE 4-10 HOST UNIT ELECTRICAL INSTALLATION CHECKLIST 10 TROUBLESHOOTING INSTALLATION TROUBLESHOOTING GUIDE 4.3.2 Installation Hardware And Tools The Host Units may be shipped individually or shipped factory pre-installed in optional cabinets. Table 4-7 lists the cables and hardware provided by the manufacturer. Additional hardware may be needed, depending on the site requirements, and may be ordered through Customer Service (Section 6). Table 4-7. Host Unit Cables and Hardware Single Host Unit Hardware and Fasteners Customer Install Factory Install Rec'd CABINET (Optional) 1 HU DC POWER CABLE 1 ALARM CONNECTORS 8 FIU-S INTERFACE CABLE 3 FIU-NS INTERFACE CABLE 4 GROUNDING CABLES 1 POI GROUNDING CABLE (Optional) 1

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 40 Single Host Unit Hardware and Fasteners Customer Install Factory Install Rec'd POI INTERFACE CABLE 4 The following is a list of tools and any additional materials required for the Host Unit installation:  Small Phillips screwdriver  Wire cutters  Wire Harness (Required for Expanded Third Party Alarm) 4.3.3 Unpacking And Inspection This section provides the instruction for receiving the equipment shipment, verifying all parts have been received and checking that no damage has occurred during transportation. The Host Unit includes the following items:  Optional Cabinet with Host Unit installed as shown in Figure 4-19.  Hardware and Fasteners described in Table 4-7, Section 4.3.2 Figure 4-19. Host Unit Cabinet Use the following procedure to unpack and inspect the Host Unit and accessories: 1. Open the shipping packet and carefully unpack the cabinet or individual Host Unit from the protective packing material. 2. Verify receipt of hardware and fasteners using Table 4-7 3. Check each optional cabinet for broken or missing parts. Check each Host Unit module for any damage, particularly the Fiber Optic Port. If there is any damage or missing parts, contact BTI (Section 6) for an RMA and to reorder parts, if any replacement parts are required.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 41 NOTE: Check particularly for any damage to the fiber optic connectors on the FIU module. Check the power connectors located at the back of the Host Unit and check the back plane connectors located inside the Host Unit for any damage. . 4.3.4 Electrical Installation 4.3.4.1 Electrical Safety Precautions Please read the general Safety Precautions presented in Section 1.2 Safety Precautions 1. Follow the instructions for installation provided in this manual to prevent serious accidents including loss of life, severe personal injury or extensive property damage. 2. The Unit must be grounded before connecting any power supply. Grounding is a required precautionary measure. Grounding instructions are provided and should be followed for safety. 3. Electrical and electronic components can be destroyed by incorrectly wired connections. 4. Cable connector materials must meet manufacturer specifications to avoid corrosion at the connectors. 5. Compliance with the surge requirement of EN 61000-4-5 (fine protection) has been met by this Unit. Installing additional external surge protection, depending on the individual application, via local supply connection and/or coarse protection is recommended to avoid damage caused by electrical surges.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 42 4.3.4.2 Grounding The Unit must be grounded. The Host Unit is grounded during a factory installation in the optional cabinet with an earth-bonding cable connected to the provided grounding connection. Do not connect external devices to the grounding connection. Please verify the Unit is securely grounded. If it is no longer securely grounded, please use the following procedure to ground the Unit: Figure 4-20. Host Unit Grounding Connection 1. Find the screw at the bottom right corner of the Host Unit as shown in Figure 4-20. 2. Loosen the screw located on the grounding connection. 3. Connect the cabinet mounted earth-bonding cable between the two lock and flat washers as shown in Figure 4-21. Ensure the grounding surface is clean and free of paint, insulating material or contaminants.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 43 Figure 4-21. Grounded Host Unit (shown with optional POI Unit, also grounded) 4. Tighten the screw, making sure the cable is securely connected before moving to the next phase of the installation. 4.3.4.3 DC Power Cable Connection Danger: Please use caution when working with DC power. Ensure all power is disconnected before working on power circuit. Warning: Verify that the Unit has been ground with an earth-bonding cable to the grounding connector. The DC power cable is connected during factory pre-installation.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 44 Figure 4-22. Factory Installed DC Power Cable 1. Confirm electrical polarity of the power cables to match the customer provided DC power system. 2. Verify the DC power cable is attached securely, as shown Figure 4-22. 3. If the DC power cable is not secure, turn off all associated DC power to the Host Unit, and secure the power cables as shown. 4.3.4.4 Install the BIU and FIU modules Figure 4-23. BIU and FIU modules 1. Remove the blank module covers for the chosen module slot locations. 2. Slide the BIU and FIU modules in to each separate designated module slot, Figure 4-23. 3. Secure the screws at the top and bottom of each module. 4.3.4.5 Alarm Installation The Alarm interface is an optional customer centered configuration. The Alarm Input configuration gives the user the means to monitor third party alarms, such as battery or intrusion alarms. The Alarm Output configuration provides the customer with the means to monitor major or minor alarms via Form C relay. The alarm interface is located at the back of the Host Unit as shown in Figure 4-24.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 45 Figure 4-24. Alarm Interface 1. With wire cutting tools, prepare the connecting wires. 2. Loosen the screws in each connector. 3. Use the Input Alarm configurations shown in Table 4-8 and the Output Alarm configurations in Table 4-9 to determine the wire placement. 4. Slide the bared wires into the slot under the screw and tighten securely. 5. Plug all the alarm connectors into the Alarm Input interface as shown in Figure 4-25 and Figure 4-26. Table 4-8. Input Alarm Configuration NMS Alarm Status Alarm No Alarm Expanded Alarm 1 (User Defined) IN1/GND IN1 Expanded Alarm 2 (User Defined) IN2/GND IN2 Expanded Alarm 3 (User Defined) IN3/GND IN3 Expanded Alarm 4 (User Defined) IN4/GND IN4

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 46 Figure 4-25. Input Alarm Installation (Alarm On) Table 4-9. Output Alarm Configuration Alarm Type On Off Major COM1/NC1 COM1/NO1 Minor COM2/NC2 COM2/NO2 Figure 4-26. Output Alarm Installation (Alarm On) 4.3.4.6 Connect the BIU/FIU Modules Connect the BIU to the FIU-S with the provided interface cable using the following procedure: 1. Connect one end of the interface cable to the BIU port labeled "Tx1 Out". 2. Connect the other end of the cable to the FIU-S port labeled "Tx1". 3. Connect a second interface cable to the BIU port labeled "Rx4".

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 47 4. Connect the other end of the cable to the FIU port labeled "Rx1", Figure 4-27. Figure 4-27. Connect the BIU to the FIU For a two BIU and FIU-NS configuration, use the additional provided interface cables and the following procedure: 5. Connect the one end of the interface cable to the FIU-NS port labeled "Tx1". 6. Connect the end of the second interface cable to the FIU-NS port labeled "Tx2". 1. Connect one end of the interface cable to the BIU port labeled "Tx1 Out". 2. Connect the end of the second interface cable to the port labeled "Tx1 Out" of the second BIU. 3. Connect the end of the third interface cable to the FIU-NS port labeled "Rx1". 4. Connect the other end of the fourth interface cable to the FIU-NS port labeled "Rx2" 5. Connect the third interface cable to the BIU port labeled "Rx4". 6. Connect the fourth interface cable to "Rx4" of the second BIU. 4.3.4.7 Optional Equipment Installation The POI and Fan, (if ordered) are factory installed. Please verify the POI and Fan are securely connected as shown in Figure 4-28. Figure 4-28 POI and FAN Installation

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 48 4.3.4.8 Connect POI to BIU The Point of Interface (POI) is an optional component. The POI is connected to the BIU, Figure 4-29, using the following procedure: 1. Connect one end of a POI interface cable into the BIU port labeled "Tx1 In". 2. Connect the other end of the cable to the POI port labeled "Tx-L". 3. Connect the one end of a POI interface cable into the BIU port labeled "Rx4 Out". 4. Finally, connect the other end of the cable to the POI port labeled "Rx-L". Figure 4-29. POI to BIU Connection 4.3.4.9 Connect the Fiber Optic Cable The Fiber optic cable is connected to the FIU module by attaching the cable to the port labeled "Fiber-1" as shown in Figure 4-30. Figure 4-30. Fiber Optic Cable Connection to the FIU Module 4.3.5 Host Unit Installation Review 4.3.5.1 Electrical Installation Review

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 49 Table 4-10. Host Unit Electrical Installation Check List Items Description 1 Verify that the grounding cable is secure. 2 Confirm that the power cable connection is stable and is neither loose or damaged and that the electrical polarity is correct. 3 Verify that the fiber optic cable is securely connected. 4 Check that all installed cables are securely connected. 5 Confirm that the alarm connectors are securely connected.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 50 4.3.6 Troubleshooting

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 51 4.4 NMS INSTALLATION Caution: Network security may be compromised when accessing external Internet connectivity. The use of established security software is recommended. The NMS software is pre-installed on the Network Management Server and the NMS server arrives pre-installed in the optional Host Unit cabinet. This section provides instruction for installing the NMS software on a customer laptop or desktop and setting initial software parameters. Figure 4-31. NMS Server 4.4.1 Installation Overview The installation of the Network Management System consists of the following steps: Table 4-11. NMS Installation Overview Step Operation Type Operation Action 1 SYSTEM SET-UP VERIFY SERVER SOFTWARE IS OPERATIONAL 2 SYSTEM SET-UP INSTALL SYSTEM SOFTWARE ON TO CUSTOMER MONITORING EQUIPMENT 3 SYSTEM SET-UP LAUNCH NMS SOFTWARE 4 CONFIGURE CONFIGURE MANAGER ACCOUNT 5 CONFIGURE SET-UP USER ACCOUNTS 6 CONFIGURE SOFTWARE SYSTEM PARAMETERS 7 UPDATE/UPGRADE SOFTWARE/FIRMWARE UPGRADE INSTALL 8 INITIAL SOFTWARE INSTALLATION REVIEW CONFIRM SOFTWARE SET-UP INSTALLATION, TABLE 4-13 NMS INITIAL SOFTWARE INSTALLATION CHECKLIST 9 UPGRADE INSTALLATION REVIEW CONFIRM FIRMWARE UPDATE AND SOFTWARE UPGRADE INSTALLATION, TABLE 4-14 NMS UPGRADE SOFTWARE INSTALLATION CHECKLIST 10 TROUBLESHOOTING INSTALLATION TROUBLESHOOTING GUIDE 4.4.2 Installation Hardware and Tools The NMS server is shipped pre-installed in the optional Host Unit cabinet. Table 4-12 lists the accessories provided by the manufacturer. Additional accessories may be needed, depending on the site requirements, and may be ordered through Customer Service (Section 6). Table 4-12. NMS Cables and Accessories NMS ACCESSORY Quantity Received SOFTWARE CD-ROM 1

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 52 NMS ACCESSORY Quantity Received AC POWER CABLE 1 The following is a list of tools and any additional materials required for NMS software installation:  Laptop, Desktop PC and/or Terminal  Crossover Cable  Hub and/or Router 4.4.3 Unpacking And Inspection This section provides the instructions for receiving the equipment shipment and verifying that no damage has occurred during shipping. The NMS software is pre-installed on the server which is shipped with the following:  Optional cabinet with NMS server and Host Unit installed as shown in Figure 4-32.  Installation cables and accessories as described in Table 4-12, Section 4.4.2. Use the following procedure to unpack and inspect the NMS server and accessories: 1. Open the shipping packet and carefully unpack the cabinet from the protective packing material. 2. Verify receipt of accessories using Table 4-12 3. Check the server for visual damage. If there is any damage, contact BTI (Section 6) for further instructions including an RMA, if necessary. Figure 4-32. NMS Server 4.4.4 Verify Server software

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 53 1. Connect the laptop, PC or terminal to the server through the hub using a crossover cable, Figure 4-33. The monitoring device may also be plugged directly into the server with a crossover cable. Figure 4-33. Connecting the Monitoring Device to the Server 2. Locate the NMS icon on the screen of the monitoring device, Figure 4-34. Figure 4-34. Locate NMS Icon 4.4.5 Initial System Setup 4.4.5.1 CD-ROM Install The CD-ROM install is used to install NMS on to a Laptop or Desktop Computer. Use the following procedure to install the application on to the computer: 1. Open the CD drive on the machine. 2. Place the CD into the drive and close the drive. 3. The CD will begin the install wizard, Figure 4-35. 4. The wizard copies the files to the %ProgramFiles% folder. The default destination directory may be changed, if desired.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 54 Figure 4-35. DAS Setup Wizard 4.4.5.2 Launch NMS 1. After copying the files, the Wizard will ask to launch NMS, Figure 4-36. 2. Select Yes. 3. The Wizard simultaneously places a shortcut on to the desktop of the computer as shown in Figure 4-37. Double clicking on the NMS icon on the desktop also launches the NMS Login screen. Figure 4-36. NMS Launch from Wizard Installation

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 55 Figure 4-37. NMS Desktop Shortcut NOTE: Occasionally, there are compatibility problems that cause a configuration conflict when setting up the NMS. Follow the steps shown in the Troubleshooting Guide. If this does not resolve the issue, contact Customer Service (Section 6). 4. Verify that the Advance box is checked and then click in the password field, Figure 4-38. 5. Enter the following default password: 1 6. Click on OK. The NMS Command Console is then launched. Figure 4-38. NMS Login Screen 4.4.6 Initial Start-up Configuration Once NMS is installed on the machine, the command console or main screen is used to navigate through various NMS menus to configure both the software system parameters and the DAS system parameters. This section covers the software system parameters needed to set-up an initial install. Main access to the NMS software configuration is through the System(S) drop down on the Menu bar as shown in Figure 4-39. User accounts may also be accessed through the User Icon on the Command toolbar as shown in Figure 4-40. The software system configuration includes the ability to access the

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 56 following functions:  Access and manage User Accounts and passwords (Add/Modify/Delete)  Modify parameter defaults. Figure 4-39. System (S) Drop Down Menu

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 57 Figure 4-40. User Account Icon 4.4.6.1 Modify Default Accounts The NMS User Manager comes with two default entries shown in the User list. For security reasons, changing the default manager account and password is highly recommended. The default User account may also be modified by overwriting the default information. The following procedure details the steps necessary to change the default accounts: 1. Using either the System(S), Figure 4-39 or the User icon, Figure 4-40, access the User Manager screen, Figure 4-41.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 58 Figure 4-41. User Manager Screen 2. Select Manager in the User List, Figure 4-42 to see the default information.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 59 Figure 4-42. Manager Default Information 3. Delete the default entries, Figure 4-43 and enter the new user name and password. Note: There is a limit of 20 Alpha-Numeric characters for both User name and password entries. User names are selectable from the Login screen drop down menu, once entered into the system. Passwords are case sensitive.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 60 Figure 4-43. Edit Default Entries 4. Click Modify to update the User and Password. 5. Click Return to return to the NMS Command Console or continue to add or update User Accounts. 4.4.6.2 Set-up New User Accounts Adding a New User is easily managed through the User Manager screen. Access the User Manager screen, then use the following procedure to add Users of various levels: 1. Currently, there are two levels available for User Accounts. Once the User Manager screen is up, select the User level, as shown in Figure 4-44.  Supervisor: This level acts as an administrator for the Network System. This level can make edits and set custom features.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 61  Observer: This level is a monitoring functionality only. This level is most commonly used for users who will monitor the system and review alarm logs. At the Observer level, a user may only: modify their user name and password and; view, save and print Alarm information.Figure 4-44. Select a User Level 2. Enter a user name and password, Figure 4-45. Then click Add.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 62 Figure 4-45. Enter User name and Password Note: There is a limit of 20 Alpha-Numeric characters for both User name and password entries. User names are selectable from the Login screen drop down menu, once entered into the system. Passwords are case sensitive. 3. Additional detailed information for managing User accounts, including deleting and modifying User accounts is contained in the NMS User Manual. 4.4.6.3 Configure Software Parameters The NMS system software parameter defaults allow the user to focus less on configuring the software system , Figure 4-46, and more on the critical functionality for the DAS system. The NMS is designed to run in a background mode when the SNMP option is activated. The background mode allows constant communication with the NOC while leaving the user's device accessible. The NMS icon resides in the Icon Tray in the status bar of the user's device. Detailed parameter information is available in the NMS User Manual.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 63 Figure 4-46. System Parameter Screen 4.4.7 Firmware Update DAS components periodically require firmware updates. The following list of components may require periodic firmware updates:  BIU  FIU  PA  RCU  Remote Unit A notification email is sent with the firmware update attached as a file to the email. The following procedures detail the firmware update process: 1. Verify the email is genuine and the file attachment is safe for download. The sent file will be named in the following manner and have a file extension of .s: DAS8345_[Component]_[Version].s 2. Download the attached file to any chosen folder or the desktop. Note the folder name, if saved to a designated folder.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 64 3. Log into the NMS System. 4. Click on NetConfig 5. Using the RemoteSoftwareDownload interface, Figure 4-47, Locate the file by clicking on the browse button. Figure 4-47. Remote Software Download Screen 6. Click Start Download. The firmware update may be paused if needed by clicking the Pause button. 7. Once the download is complete, click Return. 4.4.8 Software Upgrade Installation 4.4.8.1 CD-ROM Install The CD-ROM Upgrade install is a quick and simple installation. Use the following procedure to install the application on to the computer: 1. Check that no instance of NMS is running. 2. Open the CD drive on the machine. 3. Place the CD into the drive and close the drive. 4. The CD will begin the install wizard and ask if the user would like to overwrite the older NMS version, Figure 4-48.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 65 5. Select Yes. Figure 4-48. Replace NMS File 1. An error dialog box will appear, Figure 4-49, if the older version of NMS is open and running. 2. Close NMS and click Try Again. Figure 4-49. NMS Update Fail Error Box 4.4.9 NMS Upgrade Installation Review

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 66 Table 4-13. NMS Initial Installation Checklist Items Description 1 Verify that the CD is undamaged and the server software is installed. 2 Confirm that the version number once the set-up Wizard launches NMS. 3 Verify that the shortcut launches the NMS Login. 4 Check that the default Manager Account and password have been updated. 5 Confirm that new User accounts and passwords have been added. Table 4-14. NMS Firmware Update and Software Upgrade Checklist Items Description 1 Verify that the email and attachment. are genuine. 2 Confirm that the firmware update is downloaded to the appropriate folder on the computer. 3 Verify that firmware update was complete from the RemoteSoftwareDownload interface. 4 Confirm that no instance of NMS is running before beginning Upgrade installation. 5 Check the version number to verify upgrade once the set-up Wizard has launched NMS.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 67 4.4.10 Troubleshooting

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 68 5 mBSC DAS SYSTEM START-UP When the system component installations are complete, the system must be configured. Please refer to the applicable System Operation and User Manual for detailed system configurations, operations, and troubleshooting/test procedures 5.1 SYSTEM COMMUNICATION Once the components have been installed, the system should be activated by establishing communication through the Host Unit and configuring the system to the network through the NMS. 5.1.1 Establishing a Host Unit communication The Host Unit hardware default IP address must be updated with the customer's network IP address. This is accomplished by first establishing a communication link, setting up the initial base system and configuring the IP Address parameter. Use the following procedure to establish communication with the Host Unit : 1. Connect the NMS installed Laptop ethernet port to the RCU front ethernet port with a cross or null modem cable. 2. From the Laptop, click the Start Button, then Settings and Network Connections, Figure 5-1. Figure 5-1. Open Network Connections 3. Select the LAN Icon and click on File then Properties, Figure 5-2.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 69 Figure 5-2. LAN Properties 4. Click on Internet Version Protocol (TCP/IPv4) and then click on Properties, Figure 5-3.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 70 Figure 5-3. Select Internet Protocol Version 4 5. Click on the second option, Use the Following IP Address:, Figure 5-4, and manually enter the IP Address: 128.0.2.30. The Subnet mask will automatically default to 255.255.0.0.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 71 Figure 5-4. Manually Enter the IP Address 6. Click OK. 5.2 INITIAL NETWORK CONFIGURATION Once installed and software configurations are complete, the network must be configured and activated. The first half of this section details the initial functions necessary for a basic system activation through the NMS. The second half details in-depth information for network system parameters. Access to the DAS system configuration Net Config Manager is through the Network(N) menu bar drop-down or the Net Config Command bar button, Figure 5-5, the ALT key + (N) or the Netconfig Icon on the Command bar. The DAS Net Config Manager includes the ability to access the following functions:  Add/Modify/Delete Sites  Add/Modify/Delete the Host Unit(s)  Add/Modify/Delete the Remote Unit(s)

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 72 Figure 5-5. Accessing the Network Configuration screen The NMS software provides an example configuration as shown in Figures 5-5 and 5-6. The example may be deleted or the example information may be overwritten with customer specific information and then saved by clicking the Modify button. For the purposes of this installation manual, the example has been deleted to provide the most accurate details.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 73 Figure 5-6. BTI Example System Configuration 5.2.1 Add a Site The highest level of system configuration is defined by adding a Site Caption and a Site Code. The Site Caption alpha-numeric text field accepts any user-defined descriptive name (30 alpha-numeric character limit) and the Site Code accepts integer values only (1 through 9999 numeric limit). The following steps are used to add the Site Caption and Site Code: 1. Access the Network Config screen, Figure 5-5, via the NetConfig Icon on the Command bar, using ALT + (N) or the Network(N) menu drop-down. 2. Click on the Site button in the Select Information field,, Figure 5-7. 3. Enter the Site Caption (Customer defined Site Name) and the Site Code (Customer defined Site Number). The example, BTI_Example_Cypress_Site is shown in Figure 5-8. 4. Click Add to save the Site Caption and Site Code.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 74 Figure 5-7. Add a Site

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 75 Figure 5-8 Adding a Site 5.2.2 Add a Host Unit Once the Site Caption and Site Code have been configured, the Host Unit should be added to the system. The HU Caption alpha-numeric text field accepts any user-defined descriptive HU Caption (20 alpha-numeric character limit) and HU No. accepts integer values only (1 through 9999 numeric limit). The following steps provide the Host Unit configuration: 1. Click on Equipment to bring up the new information section for the DAS System equipment. 2. Click on HU in the Select Equipment section. Verify that the Site Caption and Site Code are correct for the Host Unit being added. 3. Add the customer designated HU Caption and HU No. as shown in Figure 5-9.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 76 Figure 5-9. Adding a Host Unit 4. Verify that all changes have been correctly entered and click Add, Figure 5-10.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 77 Figure 5-10. Configured Host Unit 5.2.3 Configuring the Host Unit Hardware Card Once the Host Unit has been added to the system, the IP address for the Host Unit must be changed from the default to the designated network IP address in the Host Unit Hardware Card. Configuring the IP Address is done from the Main Command Screen. The following procedures outline the steps necessary to change the Host Unit IP Address: 1. From the Main Command Screen, Select the added HU. 2. Select the RCU Module, Figure 5-11. 3. Then click on the Config tab.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 78 Figure 5-11. Select the HU 4. Click on Parameter List. Then click Select All. 5. Click on Read, Figure 5-12.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 79 Figure 5-12. View the Current Values 6. Confirm Select All is unchecked. Click on Site IP Address in the Parameter List. 7. Click Edit. 8. Enter the new IP Address in the Edit Value Column, Figure 5-13. 9. Click Set, Figure 5-14.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 80 Figure 5-13. Enter the New IP Address

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 81 Figure 5-14. IP Address Update Setting 5.2.4 Map the IP Address to the NMS Software 1. Click the Netconfig button. 2. Select the Host Unit. Figure 5-15. 3. Change the IP Address(HU) from the default value to the designated network IP address. This will map the IP Address in the NMS System to the HU hardware card. 4. Then Click Modify. Click Return 5. Restart NMS to set the new parameters.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 82 Figure 5-15. Modify IP Address(HU) From the Main Command Screen: 1. Select the updated Host Unit. 2. Click on Parameter List. Then click Select All. 3. Click on Read, Figure 5-16. 4. Confirm that the HU Hardware Card IP Address matches.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 83 Figure 5-16. Confirm IP Address Update Accepted. 5.2.5 Adding a Master and/or a Slave Remote Unit Once the Site Caption, Site Code, and Host Unit have been configured, the Master Remote Unit should be added to the system first, followed by any Slave Remote Units. The RU Caption alpha-numeric text field accepts the default RU Caption or any user-defined descriptive RU Caption (20 alpha-numeric character limit) and the RU No. field accepts integer values only (1 through 9999 numeric limit). NMS creates a default name using a combination of representative letters and numbers in the following format: S#F#_MRU###(#) [Slot#][Fiber # designation]_[MasterRU][Frequency] The example in Illustration 5-17, S4F2_MRU850 shows the default name with an M designator for Master. S#F#_SRU###(#) [Slot#][Fiber designation]_[SlaveRU][Frequency] The example in Illustration 5-18, S4F2_SRU1900 shows the default name with an S designator for Slave. 5.2.5.1 Adding a Remote Unit Use the following steps to define the Remote Unit configuration: 1. Click on the new HU in the System Net section. 2. Click on Equipment to bring up the new information section for the DAS System equipment.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 84 3. Click on RU in the Select Equipment section. 4. Select the Slot No. for the Remote Unit. Use Table 6-1 as a guide for determining the Slot, Fiber and Type selections. 5. Select the Fiber value. 6. Select the Type of Remote Unit. Selecting the Type of Unit also designates the Master or Slave configuration. 7. NMS creates a default name based on the chosen slot, fiber and type values selected as shown in Illustration 6-13 and Illustration 6-14. The default name may be deleted and may be replaced with a customer designated name as the RU Caption, if desired. 8. Verify that the Site Caption, Site Code and HU No. are correct for the Remote Unit being added 9. Click Add. Figure 5-17 Adding Master Remote Unit

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 85 Figure 5-18. Adding a Slave Remote Unit Table 5-2. Slots, Fiber and Type Values Name Configuration Value Slot Represents the slots on the HU from Left to Right that can be assigned to various equipment. Slots 1-6 are reserved for the FIU and BIU. Designating a slot number maps the RU to an FIU. Fiber Maps the RU to the Fiber connection on the Host Unit to the associated FIU. Type Defines the frequency used and must match the RU type installed. There are currently four different types of Remote Units. 700 MHz, 850 MHz, 1900 MHz, and 2100 MHz. 5.2.5.2 Modifying or Deleting a Remote Unit Use the following steps to modify or delete a Remote Unit: 1. Select the Remote Unit from the System Net section. 2. To delete the Remote Unit, click Delete. 3. To modify the Remote Unit, enter the changes desired and press Modify. The Remote Unit caption, Slot, Fiber and Type may be changed using the Modify button.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 86 5.2.6 Connect Host Unit to Server With the IP address updated, the Host Unit must be connected the server, Figure 5-19, for communication information to function. The Host Unit is connected from the Network port on the back interface through the hub to the server as shown in Figure 5-20 or may be directly connected from the back interface port to the server. The Host Unit may also be connected to the server from the RCU network port on the front interface, either directly or through the hub to the server. Only one network port connection may be used at a time. Figure 19. Connect Host Unit to Server Only one port may be connected to the server at a time, as both front interface and back interface network ports are the same port. Figure 5-20. HU Back Interface Network Connection 5.3 MANAGING AND MONITORING ALARMS 5.3.1 Alarm Manager The NMS is also the means for managing and monitoring the DAS systems through the Alarm Manager(A) menu or the Alarm Icon on the Menu bar. The managing and monitoring of the DAS system is more completely detailed in the BTI NMS User Manual.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 87 Figure 5-21. Alarm Manager 5.3.2 Configuring Standard Alarm Defaults Configuring NMS is easily accomplished through the Custom Alarm tab, Figure 5-21. Select the alarm type and click the Select button for the appropriate category. Table 5-3 provides a recommended list of alarms by category that may be selected to create a custom alarm configuration.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 88 Figure 5-22. Configuring Custom Alarm Levels Figure 5-23 shows an active alarm.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 89 Figure 5-23. Active Alarm Screen The Table5-3 provides alarm indicator descriptions for the mBSC DAS system. Alarm types for the Host Unit and Remote Unit monitored by the NMS are included as well as optional components such as the POI. The recommended category for the alarm indicator is included in column 3 of the table along with the affected component. Critical alarms indicate system failures that disable the uplink or downlink operation. Other categories, such as Major, may indicate impaired performance, but not the catastrophic system failure or a specific RU node failure.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 90 Table 5-3. Host Unit Alarm Indicators by Category Alarm Indicator Description Category Component Downlink Function Alarm Downlink overvoltage or component issue Critical PA Downlink OverPower Transmit Power exceeds rated output Critical PA Downlink OverTemperature MCPA is operating at an unsafe temperature Critical PA (Fiber Module) Downlink VSWR Antenna system VSWR exceeds preset level Critical PA Fiber Light Rx RU fiber RX failure Critical Remote Unit Fiber Light Tx RU fiber TX failure Critical Remote Unit Fiber1 Light RX FIU Fiber1 port RX light fail Critical Host Unit FIU Fiber1 Light TX FIU Fiber1 port TX light fail Critical Host Unit FIU Fiber2 Light RX FIU Fiber2 port RX light fail Critical Host Unit FIU Fiber2 Light TX FIU Fiber2 port TX light fail Critical Host Unit FIU mRU and sRU1 comm Master to Slave communications failed Critical Remote Unit mRU and sRU2 comm Master to Slave communications failed Critical Remote Unit Uplink Alarm RU Receive LNA failure Critical Remote Unit BIU No Communication BIU to RCU comm failure Major Host Unit FIU No Communication FIU to RCU comm failure Major Host Unit POI Fan1 POI Fan1 failure Major Host Unit POI POI Fan2 POI Fan2 failure Major Host Unit POI RCU +5V Host Unit RCU power supply alarm Major Host Unit RCU RCU +9V Host Unit RCU power supply alarm Major Host Unit RCU RCU No Communication NMS to RCU comm failure Major Host Unit RU Control Alarm RU Internal PA to CPU comm failure Major Remote Unit RU Fan1 RU Fan failure Major Remote Unit RU Fan2 RU Fan failure Major Remote Unit Uplink Pilot Power Uplink Pilot Power Failure Minor Remote Unit Expanded Alarm Input 1 Expansion User Defined Third Party Component Expanded Alarm Input 2 Expansion User Defined Third Party Component Expanded Alarm Input 3 Expansion User Defined Third Party Component Expanded Alarm Input 4 Expansion User Defined Third Party Component

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 91 5.3.3 System Activation Review Table 5-4. System Start-up Review Items Description 1 Verify that the Host Unit communication was established. 2 Confirm that at least one Site has been added. 3 Verify that the Host Unit Hardware card IP address has been configured. 4 Check that the Remote Unit is communicating with the Host Unit 5 Confirm that the Host Unit is connected to the Server.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 92 5.3.4 Troubleshooting

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 93 6 Maintenance 6.1 GENERAL Please read the general Safety Precautions contained in Section 1.2 Safety Precautions The mBSC-H Fiber Distributed Antenna System (DAS) system has been designed to require minimal maintenance with component replacement as the primary method of maintenance. Care must be taken to prevent unintentional damage to any module seals. Only units which can be replaced without tuning or soldering are listed in the Replacement Parts List as Warranty may be voided if the module seals are damaged. It is important to work within the Return Material Authorization (RMA) process when ordering replacement parts. Appropriate tools are required for correct handling of replacement maintenance. Please follow any replacement instructions provided by the manufacturer. Fastening procedures are as follows:  Fastening: Clockwise turns of the tool are required  Unfastening: Counter-clockwise turns of the tool are required Table 6-1: Replacement Parts List BTI mBSC-H Component BTI Replacement Parts Notes Host Unit BIU FIU RCU PSU Remote Unit Mounting Bracket Shroud Fan Unit Remote Unit NOTE: It is important to label any unlabeled cables. prior to disconnecting the cables, to maintain proper connections once any inspection or maintenance is complete. NOTE: All internal housing interventions may void Warranty as module seals may become damaged. Replace any defective parts with original parts from the manufacturer. 6.2 HOST UNIT NOTE: It is important to note that preventative maintenance is not required for the Host Unit. It is important to note that preventative maintenance is not required for the Host Unit. In the event, a

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 94 component of the Host Unit requires replacement, care must be taken with modules so that seals are not damaged unintentionally as this may void warranty. Please see the Replacement Parts List for specific components available. 6.3 NMS The NMS may require periodic updates, both Firmware and Software. Please see Sections 4.4.7 Firmware Updates and 4.4.8 Software Upgrade Installation. 6.4 REMOTE UNITS It is important to note that preventative maintenance is not required for the Remote Unit. Danger: Disconnect the Remote Unit from the mains prior to any maintenance. NOTE: It is important to note that preventative maintenance is not required for the Remote Unit. 6.4.1 Fans Visually inspect fan units at intervals based upon the location, corresponding environment and pollution levels. Maintenance is not required for the fan units, but the fan units may be cleaned, if needed using any commercially available small compressed air device (max. 5 bar). Once an RU has been powered up for the first time, the fans rotate at full speed. After one minute, the fan speed will decrease to 75% and after another minute, the fan speed decreases to 25% and will then stay at 25% until the RU reaches its normal operating temperature. In a normal operating situation, the fans are generally operating at approximately 50% of their power, this helps prevent dust and other contaminants from settling on the fan blades and the cooling fins. A fan alarm will be generated should the fan current drop below its normal operating fan speed. Please see the Replacement Parts list should a replacement fan unit be required and follow any replacement instructions provided by the manufacturer.

mBSC-H DAS System Installation Manual Issue 7 © 2009-2014, BTI Wireless Page 95 7 CUSTOMER SERVICE CONTACT INFORMATION USA BTI Wireless 6185 Phyllis Dr. Unit D. Cypress, CA 90630, USA Tel: +1 714-230-8333 Fax: +1 714-230-8341 E-mail: Customer Service: CustomerService@bravotechinc.com Sales: sales@bravotechinc.com China BTI (Shenzhen) Co., Ltd. No.8 Building, Zone #3, Tangtou Industrial Park, Shiyan, Baoan District, Shenzhen, Guangdong P.R.China 518102 Tel: +86 755-2951-2233 Fax: +86 755-2951-2299 E-mail: chinasales@bravotechinc.com

Navigation menu