BQT Solutions BT817-2 Contactless Smart card Reader with Optional Keypad User Manual 2

BQT Solutions (Australia) Pty Ltd Contactless Smart card Reader with Optional Keypad 2

UserManual.wiki >

BQT Solutions >

BT817-2 User Manual >

Contents

1. User Manual 1
2. User Manual 2

User Manual 2

Installation Remove the cover by holding the unit by the rim and pushing the reader out with your thumbs. Note: DO NOT use a screw driver or other implement to remove cover If necessary, drill holes in the wall for the mounting screws or mounting box on which the reader unit will be placed. (Use the Drilling Template provided overleaf). 1. Place the controller and power supply cable through the grommet hole. 2. Drill the holes as indicated in the template. Note: Make sure that you don't drill through the cable. Wire connection Note: Power to the unit is provided from the listed control unit or from a separately UL listed 12V DC power-limited, access control power source. DO NOT supply power during installation. Wiring methods shall be in accordance with the Electrical wiring regulation in your country / region. Check your circuit diagram for the colour coding of the circuit wiring. The reader can be damaged beyond repair if the wiring is connected incorrectly. This will void the warranty. 1. Connect the 0V wire to the power 0V line; Note: The 0V line of all power supplies must be connected to a common 0V reference point. 2. Connect the Wiegand data wires; 3. Connect the Buzzer and LED wires; 4. Connect 12V DC wire; 5. Place reader on the wall (Make sure the wires are not crushed. This will void the warranty if damage occurs) 6. Insert and hand tighten the screws; 7. Check that the reader is level before tightening the screws; Note: Excessive tightening of screws may deform the casing, resulting in a damaged unit. This will void the warranty. 8. Turn on the 12V DC power to power up reader. 9. Allow 5 – 10 seconds for reader to finish initialization (depends on the application). Make sure reader is functioning correctly according to the application specification. External Use • Make sure the wire bundle to the reader has an IP rating of at least IP65 Handling • Handle the reader with care. DO NOT damage or drop unit before installation. This will void the warranty. • If the case is damaged, the reader may not be to the specified IP rating. Replace the reader if the case is damaged. Maintenance • Once installed the reader requires no maintenance. Troubleshooting Problem Troubleshooting steps Power on reader – reader does not start up 1. Check connections 2. Check the voltage at the reader 3. Check the current capability of the power supply Power on reader – reader keeps beeping 1. Check buzzer line 2. Check the voltage at the reader 3. Check the current capability of the power supply Power on reader – LED stays green 1. Check LED line Present a card to reader – a beep is heard but reader does not output any data 1. Check whether the card has data encoded 2. Check the wiegand connection to controller 3. Check the voltage level on wiegand data lines Present a card to reader – no response from reader 1. Try a known working card 2. Check if the reader requires to be configured with a configuration card If the problem still persists, please contact your distributor for technical support. Warranty Unless specified otherwise, the Company warrants to the Customer that’ BQT Solutions Branded Products’ (excluding third party products and software) are covered by a return to base warranty on defects in materials and workmanship affecting normal use for a period of the Warranty offered under the Standard Terms and Conditions of Sale from BQT invoice date (‘Standard Warranty’) This standard warranty does not cover damage, fault, failure or malfunction due to external causes including; accident, misuse, problems with electrical power, servicing not authorised by the Company, usage and/or storage and/or installation not in accordance with Product instructions, failure to perform required preventative maintenance, normal wear and tear, act of God, fire, flood, war, any violent or similar occurrence; any attempt by any person other than Company personnel or any person authorised by the Company to repair or support the Products and problems caused by use of parts and components not supplied by the Company. The standard warranty does not cover any items that are in one or more of the following categories: software; external devices; accessories or parts added to the product after the product has been shipped from BQT Solutions. During the warranty, period beginning on the invoice date, the Company will repair or replace faulty products (at its absolute discretion) returned to its’ factory. The Customer must prepay shipping and transportation costs and insure the shipment or accept the risk of loss or damage during such transportation. The Customer shall be solely responsible for determining suitability for use and the Company will, in no event, be liable in this respect. This standard warranty is given in place of all warranties, conditions, terms, undertakings and obligations implied by statute, common law, trade usage, and course of dealing or otherwise including warranties or conditions of merchantability, fitness for purpose, satisfactory quality and / or compliance with description, all of which are hereby excluded to the fullest extent permitted by law.