BLUEBIRD BIP6000MAXID RFID Reader User Manual BIP 6000 0903 indd

BLUEBIRD INC. RFID Reader BIP 6000 0903 indd

User Manual

BIP-60001www.bluebirdsoft.com
FCC (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technical for help. – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technical for help. – WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions: 1. This device may not cause harmful interference, and 2. This device must accept ant interference received, including interference that may cause undesirable operation.
PIDION aims for leading brand in the future mobile industry. As a global brand representing the image of reliability, representativeness, and cutting-edge technologies, this mark has been registered by Bluebird Soft Inc. around the world to be protected under trademark-related laws.※ Please read warnings and cautious before use.Device type User’s guidanceA-level(IT device at work)This device is registered as suitable for electromagnetic wave use at workplace. It should be appropriately considered by dealers or users. If you sell or buy this device by mistake, please replace it with a product for home use. Type registration This wireless device may cause propagation interference, and so, it cannot be used for life-saving services.User’s guidanceTrademark This User’s Manual is protected under the related copyright laws. This User’s Manual is produced by Bluebird Soft Inc. The company has made every effort to avoid errors and omissions. Please understand that some parts may not reect the actual state. The supplied basic programs are protected under. Reproduction, transfer or deletion of the programs without prior consent is strictly prohibited. Depending on users’ environments, programs or peripherals, some parts of this Product may not work normally. This wireless device may cause propagation interference, and so, it cannot be used for life-saving services.Copyright
BIP-60001Contents 2 Safety Instructions I 3 Safety Instructions II 4 About the product 1. Checking components 2. Checking names of parts 3. Buttons 4. Features 5. Communication spec. 12 Learning basics 1. Mounting/Dismounting battery 2. Inserting/Removing USIM/USAM card 3. Setting password 4. Inserting/removing MicroSD card 5. Charging a terminal with a desktop charger 6. How to use 4Slot Cradle 7. About battery 8. Switching On/Off power 9. Communication status indication 5. Managing Delected Items 6. Managing Sent Messages 49 Camera 1. Taking photos 2. Viewing album 52 Settings 1. Setting personal environment 2. Setting system environment 3. Setting connection environment 67 Value Pack Details 70 Q & A 71 Knowing the product 73 Customer Service 74 Service Center Information 76 WarrantyCerticate 38 Inputting text 1. Selecting Text Input Mode 2. Block Recognizer 3. Key Pad 4. Keyboard 5. Letter Recognizer 6. Transcriber 41 Phone program 1. Making a call 2. Receiving a call 3. Rejecting calls 4. Ending calls 43 Phonebook 1. Searching phonebook 2. Registering entry 3. Viewing menu 46 Text Message 1. Creating a Text Message 2. Sending a Text Message 3. Viewing Text Messages 4. Managing Draft Messages 10. Adjusting screen 11. Using stylus pen 12. Using earjack 13. Resetting terminal 14. Hard-resetting 15. Using IrDA 28 Using USB cable 29 Connecting ActiveSync 1. Installing ActiveSync 2. Using ActiveSync 34 Using barcode reader 1. Using barcode 2. Scanning barcode 3. Reading barcode 36 Today Screen 1. Viewing Today Screen 2. Setting photo image as the background image 3. Adjusting volume 4. Checking battery
2BIP-6000 ManualRead these instructions and warnings to use the Product in a safe manner and to prevent accidents.Cautions in relation with batteries Batteries may explode when damaged, impacted, heated, flooded or taken apart with a gimlet. Make sure to keep the batteries out of reach of children or pets. Do not use the Product in the area with the risk of explosion. If the Product is wet, do not put it in a device that may heat the terminal (heater, microwave oven, etc.). Heating batteries may cause an explosion, deformation or fault. (Water or any other liquid will change the color of the label inside the terminal. In this case, no warranty service will be provided.)Safety Guideline Do not use the Product on an airplane or in a hospital. Do not operate the Product or search a phone number while driving a car. If it is unavoidable, please use a hands-free kit or stop the car. Batteries may become deformed and get in trouble if they are left in a hot and sealed place such as on a dashboard of a car under the direct sun light.Safety Instructions IDo not flashing scanner light in human and animal’s eyes. It could cause the damage of retina and amblyopia. Make sure that battery terminals (metal part) should not contact with any conductive materials like a necklace or coin. Also make sure that batteries should not be damaged by teeth or a nail. Impact may cause an explosion of batteries. Use dedicated batteries only and do not use the batteries for any other purpose than operating this Product. Using an inauthentic battery may reduce life of the Product, or cause an explosion. (In this case, no warranty service will be provided.) Make sure to use the adapter or the standard charger supplied with this Product. Using an inauthentic charger may reduce life of batteries or cause an explosion. (In this case, no warranty service will be provided.)Caution in relation with Laser Scanner
BIP-60003Safety Instructions IIRead these instructions carefully to keep yourself safe and to avoid loss of property.1. This Product is EMC-compliant. For safety and health, use the authentic parts supplied by the manufacturer. Any inauthentic part may affect safety.2. Do not press the power button when the Product is wet. Touching the adapter or power cord with wet hands may cause an electric shock.3. Do not modify, disassemble or repair the Product at your discretion. Manufactor if there is a problem in the Product. Also, make sure to follow the warnings and Instructions. If you fail to follow any of the above instructions, no warranty service will be provided.4. Record the data in the Product and keep it in a separate place. Data stored in the Product may be deleted during repairing or upgrading the Product. So, make sure to back up important data. (Bells, text/voice messages and characters are initialized.)5. Do not use this Product in a hot or humid place. Using the Product under a hot/humid temperature such as rain or sauna may cause a trouble. In this case, no warranty service will be provided.6. Keep this Product away from magnetic products such as credit card, telephone card, bankbook and traffic ticket. The magnetic field of the terminal may affect the data.7. Avoid vibration and impact. When not in operation or when you are absent, pull out the power cord, and keep the Product in a safe place.8. Avoid any dusty place, and keep the power cord away from any heating device. When cleaning the Product, pull out the power cord first. Dust off the pins of the power plug.9. When storing a battery for a long period of time, recharge it and keep it at a room temperature. Even a fully charged battery will suffer reduced life due to the characteristics of the battery.10. Painting this Product may damage appearance or display, or may cause a fault. Peeled-off paint may cause allergies depending on the physical conditions. In this case, stop using the Product and see a doctor.
4BIP-6000 ManualAbout the productThe images in this User’s Manual may not reect the color and shape of the actual product.Please contact the Customer Care Center if you wish to purchase any additional or optional products.[ USB cable ][ BIP-6000 Main Body ]Checking components1[ Stylus Pen ][ Desktop Cradle ] [ Battery ][ Adapter ] [ Spring Wire ]
BIP-60005Checking names of parts2Power ButtonSpeakerPower LEDCommunication LEDLCD ScreenDirection/Call/End/Number/Character/Function ButtonsBarcode Scanner WindowStylus PenUSB Cable ConnectorStylus Pen Strap/Hand Strap Holder - TopFlashCameraSpeakerReset ButtonBatteryBattery Fixing PinHand Strap Holder - BottomEarphone JackSide Scanner ButtonIrDASide Scanner ButtonMicrophoneFront Scanner Button
6BIP-6000 ManualAbout the productButtons3Button DescriptionPower buttonUsed to switch On/Off the terminal.Barcode buttons (Right/Left)Used to operate the barcode functions.During a callUsed to adjust call volume during a call.(Right : Volume up / Left : Volume down)Barcode buttonUsed to operate the barcode functions.Camera buttonPress this button during a camera function to take a photo or video.Button DescriptionArrow buttonsUsed to move left/right/up/down.Call button Used to start the phone program. If you press this button once while using the phone program, a call is made to the last party in the call list.Press ‘Send’ button on the keypad to connect Internet Explore. (WLAN only termninal)End buttonEnds the phone program. You can nish a call by pressing this button during the call.You can also exit an application program.Press and hold (at least 3 sec) this button to switch off the phone function.
BIP-60007Button DescriptionSHIFT buttonUsed to switch between Lowercase/Uppercase English alphabet. (The default is Lowercase English.)If you press this button once and then an alphabet key, the uppercase of the key is entered. Then, input mode is switched to the lowercase.If you press this key twice, the input mode is remained in the Uppercase like Caps Lock until you release it.To release the Caps Lock, you need to press the SHIFT key twice.Space buttonThe cursor moves to the right, leaving an empty space.It works like the Space key in computer.Button DescriptionBKSP buttonThe cursor moves backward, erasing the letters.It works like the Back Space key in computer.If you press and hold (at least 3 sec) this button, the letters are deleted one by one promptly and continuously.Enter buttonChanges lines in the text input mode.This button works like the Enter key in computer.
8BIP-6000 ManualAbout the productButton DescriptionWindow buttonPress this button to enable the function keys. Press and hold this button for over 2 seconds, and the start menu window appears.* buttonPress and hold this button for over 3 seconds to switch between Vibration/Ringer modes.# buttonOn the Phone main window, # is entered.On the windows other than the Phone main window, if you press and hold this key, the phone is locked.Buttons - NUMERIC3Button DescriptionMode change buttonUsed to switch the input character between Korean/English Uppercase/English Lowercase. If you press the mode switch button in the number mode, English Lowercase alphabets and symbols are displayed.The default is Numeric. Alphabets and symbols are activated until you press the mode change button again.Light buttonPress this button to set the Function key.If you press and hold this button for over 2 seconds, the LCD display light is switched On/Off. The Display On or Off status is maintained until you press the button again.
BIP-60009Button Description F1 ~ F5 buttonsThis function is user programmable.See p.48 for details.Numeric / Alphabet buttonThe default is Numeric. Used to enter numbers or alphabets.Reset buttonSoft ResetAll the programs in use are closed and the system is rebooted.Hard ResetThe product is initialized.Button DescriptionAlphabet buttonUsed to enter alphabets or symbols.Numeric buttonThe default is Alphabet.Used to enter numbers or alphabets or symbol.Window buttonPress and hold this button for over 2 seconds, and the start menu from any application without tapping the screen.Buttons - QWERTY3
10 BIP-6000 ManualAbout the productButtons - QWERTY3Button DescriptionTAB buttonThe Tab key moves the cursor to the next tab stop or the next eld (on a form).Mode change buttonChange the character mode to numeral, lower case or symbols.F1 ~ F4 buttonsThis function is user programmable. See p.48 for details.Button DescriptionLight buttonIf you press and hold this button for over 2 seconds, the LCD display light is switched On/Off. The Display On or Off status is maintained until you press the button again.Star buttonProduces an asterisk.If you press and hold this button for over 3 seconds, the phone is vibrated on.
BIP-600011Features4Item DescriptionCPU PXA 320, 806MHZOS Windows Mobile 6.1RAM 256MBROM 512MBDISPLAY 3.5” QVGA TFT-LCD/3.5” VGA TFT-LCDINTERFACE RS-232, USB 1.1 Host & Client, IRDABATTERY Rechargeable, 3.7V 4400mAh, Li-ionSIZE 80(W) x 160(H) x 35.5(D)mmWEIGHT 410g (incl. a hand strap)ADAPTER 5V 3ACommunication spec.5Item DescriptionHSDPAFrequency : TX (1922.4MHz~1977.6MHz) RX (2112.4MHz~2167.6MHz)Frequency stability : within ±200HzAntenna power : 250mWPropagation type : G7W, D7WModulation method : QPSK/BPSK(FDD)Wireless LanFrequency : 2412MHz~2472MHzNo. of channels : 13Antenna power : 10mW/MHzPropagation type : GID, D2DModulation method : DSSS/CCK(802.11b), CCK/OFDM(802.11g)BluetoothFrequency : 2402MHz~2480MHzNo. of channels : 79Antenna power : 20uWPropagation type : F1DModulation method: GFSK13.56MHZ RFID Frequency : 13.56Mhz
12 BIP-6000 ManualLearning basicsMounting a battery 1 Place the battery and push in to the arrow direction.2 Turn the battery pins inside to x the battery.Dismounting a battery1 Switch off PDA.2 Turn the battery pins outside to remove the battery. 3 Lift off the battery to the arrow direction.Before removing a battery, make sure to switch off the terminal.An abrupt power shutoff may result in a trouble.Mounting/Dismounting battery1
BIP-600013Inserting/Removing USIM/USAM card2Inserting a USIM/USAM card Insert a USIM/USAM card to the arrow direction.Removing a USIM/USAM cardRemove a USIM/USAM card to the arrow direction.
14 BIP-6000 ManualAbout USIM card? USIM (Universal Subscriber Identity Module) is a user identication card which is inserted into a W-CDMA phone.This card integrating the SIM card containing subscriber information and the Universal IC Card (UICC) containing communication and banking function provides various functions including user authentication, global roaming, and e-transaction.This chip is required for communication with the 3rd generation WCDMA terminals. You can use this card in voice mobile call including international roaming and e-commerce service regardless of type of terminal and communication service provider.Inserting/Removing USIM/USAM card - 22About USAM card?The security application module is equipped in the smart card. Being equipped inside the card reader, it authenticates the card and the terminal, encrypts communication data to protect information, and authorizes and veries communication messages.The module stores electronic value transferred from the card, and has the SAM for card authentication in the program for e-commerce.Learning basics
BIP-600015Cautions PIN code is a password used to protect the data in a USIM card. The default PIN code is <0000>, and you can change it as you like. PUK code is an 8-digit code which resets 3 consecutive PIN input errors. The PUK code is written on the envelope or the body of the USIM card. Note that the USIM card is disabled if you enter incorrect PUK codes for 10 consecutive times. The USIM card is permanently disabled if you enter incorrect PIN codes for 3 consecutive times or incorrect PUK code for 10 consecutive times. In this case, you need to purchase a new card. Please visit the nearest dealer if you forget your PIN and PUK.Setting password3In order to prevent your USIM card from being used by another person, you need to lock your USIM card.Setting a PIN codeStart ► Phone ► Menu Tab ► Options... ► Security TabClick [PIN required for telephone use], enter 4~8 digit-password, and click [ok].
16 BIP-6000 ManualInserting/removing MicroSD card4MicroSD card is a micro ash memory media which is used to store and move data. Inserting MicroSD cardPush in a memory card to the arrow direction on the SD card slot until it is completely inserted.Removing MicroSD cardIf you push the memory card in, it springs out. Then, pull out the card.Precautions Make sure to push in the memory card completely. If it is not inserted completely, the device cannot recognize the memory card. In order to remove the memory card, push the inserted memory card once, and the card springs out slightly. Then, pull out the memory card. Applying excessive force to remove the memory card will result in a fault of the device. Removing the memory card or shutting power off while using a memory card may result in loss of data, or malfunction of the card and the terminal. Make sure to back up critical data in the computer. The manufacturer resumes no responsibility for loss of data in the device. If the memory card gets stuck to the device, do not remove the card by force, but visit the nearest after-sales service center. And then, replace or return the card to the dealer from which you purchased the card.Learning basics
BIP-600017Charging a terminal with a desktop charger5Use the dedicated adapter for maximum safety and effectiveness.Power cables are sold separately. Please contact the Customer Care Center if you wish to buy one. Place the terminal on the desktop charger, and connect the adapter to the adapter jack on the rear side of the desktop charger.Adapter jack< Rear side of desktop charger >
18 BIP-6000 Manual∙PDAequippedwithacharge,asshowninthecradleafterconnectingtheadapterandpowercable.∙FourPDAcanbechargedsimultaneously.∙Mustbechargedusingadedicatedadapter.∙4400mAh(standard)battery,7hoursafterthebuffer.Highcapacity(5200mAh)DC POWER 5V Ethernet 1 Ethernet 2 USBDC POWER 5V Ethernet 1 Ethernet 2 USB6-1. Checking names of partsLED Indicator LocationLED Indicator LocationStateofcharge,pleaserefertothe“battery”LearnPC Connect buttonEachPCconnectedtotheslotbuttonispressed,thehandsetactivesyncorMDCPCandconnectthrough.※ConnectedtoonePCatatime,please.Active SyncIndicator LEDSlotPC Connect buttonHow to use Four Slot Cradle6
BIP-600019Four Slot Spare Battery ChargerSimultaneousterminalsandbatteryfittedafterthehandsetfirstchargingandfullycharged,thebatteryduringcharging.(Simultaneousterminalsandthebatterychargingdoesnot.)DC POWER 5V Ethernet 1 Ethernet 2 USBDC POWER 5V Ethernet 1 Ethernet 2 USBFour Slot Spare Battery ChargerHow to use Ethernet Hub selectoneofthetwoports.LANlineconnectionandconnecttootherEthernetcradle.DC POWER 5V Ethernet 1 Ethernet 2 USBDC POWER 5V Ethernet 1 Ethernet 2 USBDC IN Adapter Ethernet 1 Ethernet 2EthernetonlyavailablewithoutusingahubfunctionconnectanyLANportonthelinedoesnotmatteranymore.
20 BIP-6000 Manual6-2. Ethernet settingWritten that is based on BIP6000 WM6.1 ※Slightlydependingontheversionyouareusingmaydifferfromthescreenimage,butthefunctionalityisthesame.1InstallEthernetdriverinPIDION(copy->install)BluebirdSoftaWebsitetoaccessthemodelof[Driver]todownloadandinstall.2Checkthenetworkadapter,Infineon851XseriesUSB-to-LANAdapterorDavicomFastEthernetAdapteroverUSB.-TherearetwoEthernetAdaptorslike“Infineon851XseriesUSB-to-LANAdapter”and“DavicomFastEthernetAdapteroverUSB”-I f EthernetCradleproducedbeforeJuly,2011,theEthernetAdaptoris“Infineon851XseriesUSB-to-LANAdapter”-I f EthernetCradleproducedafterJuly,2011,theEthernetAdaptoris“DavicomFastEthernetAdapteroverUSB”
BIP-6000213Configurenetwork(IPaddressandsoforth)settingsUseserver-assignedIPaddress(DHCPsevrer)UsespecificIPaddress(staticIPaddress)4InstallPIDIONontoEthernetCradle5EthernetCradlemustbeconnectedcharger(powersupply)6ConnectEthernetCabletoLANPort(RJ45)7Finish
22 BIP-6000 Manual※ In order to prevent damage of battery power, the modem is switched off automatically. Please charge the battery. ※ The continuous talk time and standby time are measured under the actual environment, but may vary depending on the usage type.Charging status indicationIn charging ChargingnishedCharging lamp Red Green※ The charging indication lamp on the desktop charger and the terminal are switched to green when charging is nished. The battery will not be damaged if charging is continued. ※ The time required for charging is depending on the charging status. If the charging time gets shorter by half, you need to purchase a new battery. About battery7 Standby time (extended battery) : at least 168 hours Talk time (extended battery) : at least 8 hours Capacity (extended battery) : 4400mABattery operating timeCharging time Extended batteryTime Within 5 hoursBattery charging timeLearning basicsOperating time Extended batteryContinuous talk time At least 8 hoursContinuous standby time At least 168 hoursCharging indication lamp
BIP-600023You can switch on/off power by pressing the [Power] button on the upper part of the terminal.Switching On/Off power8For the terminals which support WCDMA communication, you can view the GSM or WCDMA 1xEVDO communication status with the [Communication status indication lamp] on the upper right side of the terminal.For the terminals whichsupport GSM communication,the lamp indicates the GSM communication status. For the terminals whichsupport WCDMA 1xEVDO,the lamp indicates the WCDMA 1xEVDO communication status.※ The wireless LAN status is not indicated with the lamp.Communication status indication9Power Button Communication status indication lamp
24 BIP-6000 ManualUse a stylus pen to select/execute/move a target on the screen. The stylus pen is attached in the top right of the terminal. TapYou can touch icons on the screen with the stylus pen to select or execute the icon as you click the left mouse button. DragUsed to select multiple items. You can select characters or images as you drag the mouse pointer. Tap and HoldUsed to view the functions of the selected item. If you tap and hold with the stylus pen, a menu pops up as you select an item and click the right mouse button.Using stylus pen11Adjusting screen10You can set the stylus pen input value on the LCD screen.Setting screenStart ► Settings ► System Tab ► Screen ► Align ScreenPoint the target in the center of the screen with the stylus pen. As the target moves to left top, left bottom, right bottom and right top, point the target accurately. Learning basics
BIP-600025Using earjack12You can use an earphone by removing the earphone cover on the right top of the terminal and inserting the earphone to the jack.Resetting terminal13Press the [Reset] button on the back of the terminal slightly with the stylus pen. Reset buttonIf there is a collision between programs or a program is stopped due to an unexpected situation, you may use the soft reset function. It is like rebooting a computer. Any information that is not saved is lost. Earjack coverEarjacks are sold as optional items. Please contact the Customer Care Center if you wish to buy one.
26 BIP-6000 ManualHard-resetting14To hard reset the terminal, you should press the button and the button at the same time.Hard-reset is used when the terminal doesn’t respond to soft-reset. Hard-reset initializes the terminal to factory default.Note that hard-reset deletes all programs, documents and settings in the memory (RAM). Bluebird Soft assumes no responsibility for loss of data and program. Therefore, you should back up critical data and programs before hard-resetting the terminal.Using IrDA15Place the terminals, with IrDA ports facing to each other. (The nearer between the ports, the communication rate increases.)IrDA portLearning basics
BIP-600027Procedures of using IrDA port1 Select Start ► Settings ► Connections Tab ► Wireless Communication.2 Select <Receive all wireless data>, and click [ok].3 Check the data to be sent, and select Menu ► Wireless Communication.4 Check the corresponding IrDA port and touch the LCD.
28 BIP-6000 ManualUsing USB cableStart ► Settings ► Connections Tab ► USB to PCYou can use various USB peripherals connected with the terminal by selecting [Use advanced network function].This menu is enabled as the peripherals are connected with the terminal through USB cables.[USB to PC] increases consumption of battery power. You can save battery by deselecting this function when you don’t use any peripherals.
BIP-600029Connecting ActiveSyncInstalling ActiveSync11 Download [Microsoft ActiveSync] from the website of Microsoft, and install the program in the PC.To connect the terminal with PC, you need to install the [Microsoft ActiveSync] program in your PC.If the [MicroSoft ActiveSync] program is already installed in your PC, you don’t need to install the program again.The screenshots are for the Korean version of [Microsoft ActiveSync 4.5].The images may vary depending on the version of [Microsoft ActiveSync], but the functions are the same.
30 BIP-6000 Manual2 On the [License Agreement] window, select <Agree> ► On the [Customer Information] window, ll in the <User Name> and <Company> eld ► On the [Target Folder] window, select the <Installation Location>. 3 The [Microsoft ActiveSync] is installed when installation process is ready.4 The [Microsoft ActiveSync] program is installed.Installing ActiveSync - 21Connecting ActiveSync
BIP-600031Using ActiveSync2The screenshots are for the [Windows Mobile] version. The images may vary depending on the version of the software.Window images for [Windows CE] are different from the samples, but the functions are the same with those of [Windows Mobile].You must connect the terminal to PC or notebook rst to use [MicroSoft ActiveSync].You can copy/paste les, or install/uninstall programs through synchronization with the terminal.USB cables are sold separately. Please contact the Customer Care Center if you wish to buy one.1 Place the terminal on the desktop charger, and connect the charger or the terminal with the computer through the USB cable. Adapter jack USB cable jack(Back of the desktop charger)
32 BIP-6000 Manual2 When the terminal is connected with the computer successfully, the [Microsoft ActiveSync] program is started automatically. Click the [Search] button.3 The <Mobile Devices> folder shows the image, music or document folders in the terminal. You can save the les in the computer.Using ActiveSync - 22Connecting ActiveSync
BIP-600033Precautions in using ActiveSyncThe message “Unknown Device” pops up after the computer detects the USB deviceThis message may be displayed when you switch on the terminal as it is mounted on the desktop charger. If you dismount the terminal and then mount it back to the charger, the ActiveSync program works properly. The message “Connecting…” continues Dismount the terminal from the desktop charger to disconnect it from the computer. On [ActiveSync], select File ► Set Connection ► <Allow USB Connection>, and then, click [ok]. Connect the terminal again. If connection attempts continue to fail and the message “Unknown Hardware Device” pos up Abnormal status of the USB host in the computer may result in connection fail. Remove the terminal from the desktop charger, reboot the computer, and then, return the terminal to the desktop charger. The terminal does not work when you remove and return the batteryTo prevent this problem, you should press the [Power] button or select [Exit] in the Start menu with the stylus pen so that Windows Mobile (or Windows CE) should “Exits System” before you remove the battery.If you had to remove the battery due to an unavoidable situation, and the terminal does not work properly,press the button and the button at the same time for hard-reset. Note that hard-resetting deletes data from the memory. Only the data in the le storage are preserved.
34 BIP-6000 ManualUsing barcode readerUsing barcode1You can scan barcodes by pressing the [Barcode] button on the side or front of the terminal. 󰚟 󰚟 󰚟 󰚟When you scan barcodes, maintain the correct distance (10cm) and angle between a barcode and the barcode scanner window.Scanning barcode2When you use barcodes in a specic program, contact the developer of the program for details. Correct scanning angle Incorrect scanning angleBarcode button
BIP-600035Reading barcode3Start ► Programs ► NotesOn <Notes>, select [New] button and read a barcode. Then, the barcode data are displayed. If you read a barcode as <Notes> is open, the barcode is saved automatically in [Notes].If you read a barcode as <Notes> is shut, because the data is not saved, you should select [New] and [Menu], and then, [Paste].
36 BIP-6000 ManualToday ScreenViewing Today Screen1Terminal states such as [Start], [Wi-Fi], [Com Status], [Volume] and [Battery] are indicated on the top of the screen.Depending on the settings, [Today Screen] may display [Date], [Time], [Wireless Access Setting], [User Info.], [Message], [Work], [Schedule] or [Lock Status].See p.50 for details.You can set the [Start] menu as you like.See p.48 for details.Setting photo image as the background image2You can set the photo taken by yourself as the background image.1 Select Start ► Programs ► Pictures and Videos ► Show ► My Documents ► My Pictures.2 Select the [Menu] button in the right bottom of the screen.3 Select [Set as Today Background...].4 Select the transparency level of the background image, and select [ok].
BIP-600037Adjusting volume3You can adjust volume of the folder/menu selecting tone or the ringer.Select in the top right of the screen, select Setting, and you can adjust system/ringer volume.If you select Vibration, the terminal is switched into the vibration mode. If you select Release, the terminal is switched into the mute mode.Checking battery4Select in the top right of the screen, and you can check the battery status.
38 BIP-6000 ManualInputting textBlock Recognizer2This input method uses the traditional writing area box split in the middle.The left side is used to write letters and the right side is for number entry.Symbols and common functions are located in other smaller boxes located in the right of the writing box area.Selecting Text Input Mode1There are five different character input methods available.
BIP-600039Key Pad3Input letter or number by terminal keyboard if choose Key Pad on terminal screen shown as below image.See Buttons on page 6~10.Keyboard4This input method displays an on-screen keyboard that can be used to input characters by tapping the screen using the stylus pen.
40 BIP-6000 ManualTranscriber6The transcriber option is similar to the letter recognizer, except instead of entering characters into a designated area, you can enter entire words and sentences using your own handwriting.Transcriber supports both printing and cursive writing styles and then automatically types the information on the screen.Letter Recognizer5This option allows you to enter text using your own handwriting.The screen is divided into three different areas. A capital letter area, small letter area, and a number area.Characters are entered by printing letters in each area. The character is then analyzed and typed on the screen automatically.Inputting text
BIP-600041Making a call1Execute the phone program by selecting the [Phone] button, enter a telephone number, and press the [Call] button to make a call.RedialingIf you press the [Call] button without entering a phone number, the terminal automatically makes a call to the last call party.Receiving a call2If the terminal rings and a call receiving message is displayed, click the [Call] button or select the [Answer] button in the bottom of the screen. ※ The calling party information message can be indicated differently from the one of normal phones.※ The phone functions are the same as the normal phones. Refer to p.21 if you wish to use an earphone.Phone program: Cancel numbers one by one.: You can make a call with speed dial number. If you select menu in the bottom right of the speed-dial screen, you can add/edit/delete speed-dial numbers. (You can save up to 98 speed-dial numbers.): You can view the list of received calls/originated calls/missed calls.: Enter a phone number and press this button to make a call.
42 BIP-6000 ManualRejecting calls3Select the [Ignore] button in the bottom of the screen or press the [End] button on the keypad to cut off an incoming call.Select the [End] button in the bottom of the screen or press the [End] button on the keypad to automatically end a call.Ending calls4Phone program
BIP-600043Searching phonebook11 Select the [Phonebook] button in the bottom right of the Today Screen, or select Start ► Contacts. 2 Enter a name in the [Enter a Name...] eld to search for the phone number.Phonebook1 Select the [New] button in the bottom left of the Phonebook screen. 2 Select the type of phone number.Registering entry2
44 BIP-6000 ManualViewing menu3Select the [Menu] button in the bottom right of the Phonebook window.Edit : You can edit the existing phone number.Send Contact : You can send a phone number through wireless communication.Copy/Delete Contact : You can copy/delete the selected phone number.3 Enter all the elds, and select [ok] in the top right of the screen to register the entry in the phonebook.Registering entry - 22PhonebookOptions... : You can select <Show alphabetical index> or <Show contact names only>.View By : You can set the display standard of phone number by name / Company.Filter : You can set lters for display.Select Contacts : You can select Several / All.
BIP-600045If you press and hold the selected phonebook entry, you can use various menus.Call Work/Home/Mobile : A call is made to the registered number.Send E-mail : An e-mail is sent to the registered e-mail address.Send Text Message : An SMS message is sent to the registered number.Copy Contact : You can copy the selected entry.Delete Contact : You can delete the selected entry.
46 BIP-6000 ManualText MessageSending a Text Message2Start ► Messaging ► Text Messages ► OutboxAfter creating Text message including masaage receiver, tap Send on the Text Messages screen.On the Text Messages screen, tap Menu and select [Add Recipient...] to add massage receiver.Maximum 18 people can be added to message reciever.Start ► Messaging ► Text Messages oron the Today screen, tap Messages.Go to Text Message screen, tap [Menu] and select [New]or Go to Phone screen, Select a contact name from Call History.Tap Menu and Select tap Contacts and select [Send Text Message]Tap Inbox on Text Message screen.Inbox shows Deleted Items/Drafts/Outbox/sent Items foldersCreating a Text Message1
BIP-600047Viewing Text messages3Checking a text message from ‘Inbox’ folder.Start ► Messaging ► Text Messages ► InboxChoose receiving message from Inbox to view the text message.Tap Received the text message at least 2 second to Reply/Delect/forward.A creating message will be stored automatically in Draft folder if error is occured in sending a message. Start ► Messaging ► Text Messages ► DraftsTap the draft message at least 2 second to Reply/Delect/forward.Tap the draft message to edit the message and resend. After sending a message, the message will be removed automatically from Drafts folder.Managing Draft messages4
48 BIP-6000 ManualManaging Delected Items5A deleted message will be stored automatically in Deleted Items folder. Find the deleted message from Start ► Messaging ► Text Messages ► Deleted ItemsManaging Sent Messages6A sent message will be stored automatically in Sent Items folder.Find the deleted message from Start ► Messaging ► Text Messages ► Sent ItemsTap the sent message at least 2 second to Reply/Delect/forward.Text Message
BIP-600049Taking photos1Start ► Programs ► CameraCameraIf you press the [Barcode] button, the terminal takes the Still/Video and automatically saves the Still/Video in the album.MenuVideo : Switches into video recording.Mode : You can select Normal/Burst/Timer.Resolution : 480×640/600×800/768×1024/1536×2048.Flash : Select/deselect ash function.Full Screen : The display is extended to the entire screen.Options... : You can select Name/Folder/Size of les.Barcode buttonIf you press the [Barcode] button in the center of the terminal as Camera is enabled, the terminal takes an Still/Video.
50 BIP-6000 ManualBy selecting the [Menu] button, you can select Delete, Send, Beam, Set as Today Background, Zoom, Edit, Properties, Options, Send to your space for the Still/Video.The terminal may get off or switch into the standby mode in case the battery is low.If the camera is not used for 1 min, the terminal switches into the standby mode.The video function may be different from this User’s Manual according to the camera program. Start ► Programs ► Camera ► ThumbnailsYou can extend/reduce the selected Still/Video, or check information on the Still/Video.Viewing album2Taking photos - 21Camera
BIP-600051By selecting the [Menu] button, you can select Zoom, Play Slide Show, Set as Today Background, Beam picture, Save, Edit, Properties, Options or Send to your space for the selected Still/Video.
52 BIP-6000 ManualSettingsSetting personal environment1ButtonsYou can set the short-cut key functions for <F1 ~ F5> buttons on the terminal.Start ► Settings ► Personal Tab ► ButtonsSetting short-cut key allocation programSelect a button, and select the program you wish to allocate to the selected button.Available programsIn addition to basic programs, you can allocate all programs installed by yourself. You can register the frequently used programs in the [Start] menu.Start ► Settings ► Personal Tab ► MenusAll the available programs are displayed on the checklist. The checked programs are indicated on the [Start] menu on the title bar. (You can check up to 7 programs.)Menus
BIP-600053Sounds TabYou can select whether to use notication tones for Events, Programs, Screen taps, Hardware buttons. Start ► Settings ► Personal Tab ► Sounds&NoticationsAs you select items, sounds and notications are set for the items, and the terminal noties you of status or event with sound.Notications TabYou can select the sound method and notication tone for status or event. Start ► Settings ► Personal Tab ► Sounds&Notications ► Notications TabYou can select Ring type and Ring tone for status or event, including phone, wireless network, alert and ActiveSync. Sounds & Notications
54 BIP-6000 ManualSetting personal environment - 21You can set owner information or memo.Start ► Settings ► Personal Tab ► Owner InformationYou can register user Name, Company, Address, Telephone, E-mail and Notes, and select if they are to be displayed when the terminal is switched on.Start ► Settings ► Personal Tab ► Today1 Select [Use this picture as the background], and select the [Browse] button.2 Select the [Folder] in which the desired photo is stored.3 Select the picture le [Type]. 4 Select the picture le and press the [ok] button.Appearance TabYou can select an image in the terminal as the background of Today screen.Owner Information TodaySettings
BIP-600055Items TabYou can select items to be displayed on the Today screen.Start ► Settings ► Personal Tab ► Today ► Items TabThe selected items on the list are displayed on Today screen. You can change the order of display of the items with the [Move Up]/[Move Down] button.Start ► Settings ► Personal Tab ► InputIf you select Option for Handwriting, you can make setting for Handwriting layout for left hander / Three handwriting input boxes / Restriction of handwriting recognition time.Options TabYou can select the voice recording format.You can select the text input method or the voice recording format.Input
56 BIP-6000 ManualSetting personal environment - 31Password TabUse this function to protect data by setting the terminal to request password every time it is switched on.Start ► Settings ► Personal Tab ► LockEnter the password in the Password eld, and enter it again for conrmation.Select [Prompt if device unused for], and enter time. The password should be 4 ~ 8 digits, and repeated numbers (e.g., [1111]) or sequential numbers (e.g., [1234]) is not allowed. If [Prompt if device unused for] is selected, if the terminal is left unused for the designated time, the following window pops up.Enter the password, and select [Unlock] in the bottom of the screen.LockSettings
BIP-600057Hint TabEnter the words which will help you remembering your password.A [Hint] window pops up if you fail to enter the correct password for 4 consecutive times. Start ► Settings ► Personal Tab ► Phone ► Phone TabRing type : You can select Ring / Increasing ring / Ring once / Vibrate / Vibrate and ring / Vibrate then ring / None. Ring tone : You can select a bell.Keypad : You can set the keypad tone from Long tones / Short tones / Off.PhonePhone TabYou can select/deselect sound of the terminal.
58 BIP-6000 ManualSetting system environment2Current status of memory (In use, Free) is displayed. Start ► Settings ► System Tab ► MemoryMain TabYou can nd Total / In use / Free for memory storage and program. Storage Card Tab You can nd the status (In use / Free) of the MicroSD memory and ProgramStore.MemoryStart ► Settings ► Personal Tab ► Phone ► Security TabSelect [Require PIN when phone is use], enter 4~8 digit password, and select [ok].To change your password, select [Change PIN].See p. 15 for details.Security TabYou can set a password for USIM card to prevent unauthorized use when it is lost or stolen.Setting personal environment - 41Phone - 2Settings
BIP-600059Program TabSelect the port to be used by the program to import the GPS data.Start ► Settings ► System Tab ► External GPSAll the programs which use GPS can communicate through this port.Hardware TabDesignate the hardware port with which the GPS device is to be connected.External GPSThe list of the programs in use and the memory status are displayed.Start ► Settings ► System Tab ► Task ManagerWith the menu, you can exit all or specic programs.Task ManagerAccess TabIf you select [Manage GPS automatically], GPS data from multiple programs can be imported at the same time.
60 BIP-6000 ManualBattery Power Tab / External Power TabYou can set the LED Off time after which the LED should be turned off automatically if no key action has been made.Start ► Settings ► System Tab ► Lighting ► Battery Power Tab / External Power TabThe shorter the LED Off time, the battery life extends longer.The LED is turned on when you press any button or touch the screen.Keypad TabSet the keypad LED Off time.Start ► Settings ► System Tab ► Lighting ► Keypad TabThe shorter the [LED Lighting Time], the battery life extends longer.The keypad remains off if no [LED Lighting Time] is selected. BacklightSetting system environment - 22Settings
BIP-600061The list of programs installed personally or by the company, except the basic programs, is displayed.Start ► Settings ► System Tab ► Remove ProgramsSelect the program you wish to uninstall, and then, select the [Remove] button.Brightness TabYou can control brightness by moving the slider bar.Start ► Settings ► System Tab ► Lighting ► Brightness TabThe nearer to [Dim], the longer the battery life extends. Remove Programs
62 BIP-6000 ManualGeneral Tab Switch the screen to Portrait / Landscape (right-handed) / Landscape (left-handed).Start ► Settings ► System Tab ► ScreenIf you select the [Align Screen] button, you can reset the stylus pen points.See p.20 for details. Text Size Tab The text size displayed on the screen can be set by 5 steps.ScreenDevices Tab Set the Bluetooth Device (Bluetooth printer, card reader, etc.) for communication with the terminal.Start ► Settings ► Connections Tab ► Bluetooth1 Search Bluetooth device at near to select [Add New Hardware].2 Choose the Bluetoothe device to connect and select [Next].3 Select [Finish] after conrming the chosen device name.Setting connection environment3BluetoothSetting system environment - 32Starting of Bluetooth device is depending on the Bluetooth device model. Please refer to the manual of the Bluetooth device. Settings
BIP-600063Mode TabYou can set communication with the Bluetooth device.Start ► Settings ► Connections Tab ► Bluetooth ► Mode TabTurn on Bluetooth : Select whether to use the Bluetooth device. To extend the battery life, you should uncheck this option. Make this device visible to other devices : This option allows BIP-6000 to be searched by other devices.COM Ports TabSelect the COM port to be connected with the Bluetooth device.Start ► Settings ► Connections Tab ► Bluetooth ► COM Ports Tab
64 BIP-6000 ManualYou can set the communication environment with PC.Start ► Settings ► Connections Tab ► USB to PCComputers adopting the tunneling VPN can make a connection with the terminal through RNDIS. In this case, uncheck [Enable advanced network functionality] before attempting to connect.If [ActiveSync] is not started when the terminal is connected with PC normally, you should select [Enable advanced network functionality].USB to PCSetting connection environment - 23You can set the Wi-Fi wireless Internet.Start ► Settings ► Connections Tab ► Wi-FiYou can set the Wi-Fi environment for access with AP (Access Points) through wireless Internet.Wi-FiSettings
BIP-600065Setting wireless Internet1 Select Wi-Fi on the Wireless Manager window. Then the list of nearby APs is displayed.2 Select an AP on the wireless networks list, and select the [Connect] button.If APs list is not displayed, set the connection manually.1 On the Wireless Network Conguration window, select [Add].2 Enter the AP name on the [Network Name] eld, and select [Next].3 After selecting [Next], check [Provide key automatically], and select [Next].4 Select [Finish], and the selected AP is displayed in the wireless networks list.5 Select the [Connect] button to connect the wireless LAN.Start ► Settings ► Connections Tab ► Wireless ManagerYou can select [All] to enable/disable three functions at the same time, or select [Wi-Fi] / [Bluetooth] / [Phone] for independent enabling/disabling.Wireless Manager
66 BIP-6000 ManualWireless Manager - 2Setting connection environment - 33When you enable this function, you can set the details of this function.When you disable this function, you can set the function independently by selecting the [Menu] button in the bottom right of the screen.SettingsTrigger
BIP-600067Handle release buttonBarcodeScanner WindowValue Pack DetailsMaxID DescriptionRFID ReaderTriggerHandle 1. Checking names of parts 2. Scanning (Scanning barcode)MaxIDToscanbarcodes1.StarttheMaxIDscanningapplication.2.AimtheMaxIDatthebarcode.3.Pressthetriggertoscanthebarcode.“Barcodereader”thecontentsoftheusermanualforthescannerfunction,seeWhen you scan barcodes, maintain the correct distance (10cm) and angle between a barcode and the barcode scanner window.Correct scanning angle
68 BIP-6000 Manual3. ChargingUsingdirectchargingcradle.Andchargingtheauxiliarybatteryatthesametime,youMaxIDcharginghandleshouldberemoved.B.ConcurrentsecondarybatterychargingA.Directcharge4. How to handle separationPressthereleasebuttonandthetopofthehandleandslidethebatterytoward.Value Pack Details
BIP-6000695. How to use RFIDContactedbytheRFTagmatchthepositionoftheantennaofRFIDinfrontofPGO.RFID AntennaItem DescriptionUHFRFIDReaderFrequency:840MHz~960MHzProtocol EPCC1G2,ISO18000-6C,ISO18000-6BRangeofmotion Max236.2inch/6m6. Device Specifications
70 BIP-6000 ManualQ The terminal is wet. What can I do?A Detach the battery from the terminal and dry it. If the terminal still doesn’t work after it is dried for a certain period of time, it is required to replace the main board and other parts.Q The terminal fails to boot.A The program might have been damaged. Reset the terminal, and if the problem continues, contact the Customer Care Center.Q The battery is not charged.A Make sure that the terminal is properly connected with the desktop charger, and check if the lamp works properly. Rub off the charging terminal clean. If it is not charged normally, it can because of aging or failure of the battery. (Warranty period for a battery is 6 months.)Q How can I ask for after-sales service?A Please send the product to the Customer Care Center in the head ofce through a pre-paid delivery service. Upon repairing the product, we will send you the product through a pre-paid delivery service.Q Can I check if the terminal is sent accurately?A You can get the invoice number from the Customer Care Center in the head ofce. Contact the delivery service to nd out the current location of the terminal.Q The battery goes dead too soon.A Peripherals such as barcode reader and printer will consume a large amount of battery power. If this phenomenon continues, it may be because of aging of the battery. You should use a new battery.※ If the product does not work normally despite the measures taken as mentioned above, please contact the nearest Customer Care Center.※ Repairing fee will be charged for the product of which warranty period (1 year from the date of purchasing) is expired.Q & A
BIP-600071FCC RF EXPOSURE INFORMATIONWARNING! Read this information before using your phoneIn August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters.Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards.CAUTION : Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could impair call quality, damage the phone, or result in violation of FCC regulations. Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for replacement antenna.Body-worn OperationThis device was tested for typical body-worn operations with the back of the phone kept 1.5 cm. from the body.SAR compliance for body-worn operation is restricted to belt-chips, holsters or similar accessories that have no metalic component in theassembly. The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue.BIP-6000 Device(FCC ID : SS4P1770) has also been tested against this SAR limit. The highest SAR value reported under this standardduring product certification for use at the ear 1.25W/kg and when properly worn on the body is 0.289 W/kg.WARNINGAny changes or modification not expressly approved by the party responsible could void the user's authority to operate the device.Specific Absorption Rate (SAR) certification informationYour device conforms to European Union (EU) standards that limit human exposure to radio frequency (RF) energy emitted by radio and telecommunications equipment. These standards prevent the sale of mobile devices that exceed a maximum exposure level (known as the Specific Absorption Rate, or SAR) of 2.0 watts per kilogram.During testing, the maximum SAR recorded for this model was 0.565 watts per kilogram. In normal use, the actual SAR is likely to be much lower, as the device has been designed to emit only the RF energy necessary to transmit a signal to the nearest base station. By automatically emitting lower levels when possible, our device reduces your overall exposure to RF energy.The Declaration of Conformity at the next page of this guide demonstrates your device’s compliance with the European Radio & Terminal Telecommunications Equipment (R&TTE) directive.Knowing the product
72 BIP-6000 ManualI hereby declare that the product.MANUFACTURER or AUTHORISED REPRESENTATIVE :- Address Bluebird Soft., Inc. SEI Tower 13~14F, 467-14, Dogok-dong, Gangnam-gu, Seoul, Korea (Postal Code 135-856)This declaration is issued under the sole responsibility of themanufacturer and, if applicable, his authorized representative.POINT OF CONTRACT:Satisfies all the technical regulations applicable to the product within the scope of Council Directives 99/5/EC, 89/336/EEC, and 73/23/EEC:All essential radio test suites have been carried out.NOTIFIED BODY : EMCCert Dr.Rasek- Address Boelwiese 5, 91320 Ebermannstadt, Germany, Identification Number : 0678BIP-6000 (HSDPA communication)※ The CE certification of the BIP-6000 for HSDPA communication.Model BIP-6000MAXIDType PDAHealth EN 50360, EN 62209-1Safety EN 60950-1+A11, EN 60825-1EMC EN 301 489-1/-3/-7/-17/-24Radio EN 301 511, EN 301 908-1/-2,EN 300 328, EN 302 291-1/-2,EN 300 440-1/-2Company Bluebird Soft., Inc.Phone number +82-2-548-0740Fax number +82-2-548-0870
BIP-600073Customer ServiceBefore Requesting After-Sales Service Before asking for after-sales service, please back up the data from the terminal. We do not back up data from the products received in the Customer Care Center. Therefore, we assume no responsibility for loss/deletion of data.Bluebird Soft Customer Service FAX : +82-2-548-0870 E-Mail : mookseven@bluebird.co.kr Address : Customers service center, SSang-young IT twintower B 703, Sangdaewon-dong 442-5, Joongwon-gu, Sungnam-si, Keonggi-do, KoreaOperating hours Mon.-Fri. : 9:30 A.M. ~ 6:30 P.M. (GMT Time: +9 Hours) The center is closed on Saturdays, Sundays and holidays.Registering for After-Sales Service We receive the products for after-sales service through mail, delivery service and hand carry only in principle. If you bought the product from any party other than the authorized dealer, you need to register the product before asking for after-sales service. Please enclose an evidence of purchasing or the receipt to the product for after-sales service. Please enclose the name, telephone number, address and symptom for prompt service. You can ask for after-sales service through the dealer or the Customer Care Center in the head ofce. Do not intentionally damage the label on the product. Damaged label may result in a disadvantage to the customer. When you return the product to Bluebird Soft for service, please put the product in a protective box. No warranty will not be provided for any damage occurring during delivery. We recommend you to use the box and protective cover supplied with the product. Make sure to deliver the product in a safe way. Bluebird Soft assumes no responsibility for loss of the product during delivery.
74 BIP-6000 ManualRegulations on Free/Charging Repairs The after-sales service will be provided according to the regulations for compensation for customers. The parts of the product will be retained for 3 years. Replacement will be made with the same model in principle. If the same model is not available, a similar model will be provided as a replacement. The customer may select refund if he/she does not want replacement with a similar model. Refund will be made based on the price on the receipt. If the price on the receipt is higher than the normal price, it is considered to include incidental expenses. In this case, refund will be made based on the normal price.Type of Customer Damage Contents of CompensationWithin the Term of Guarantee After term of guaranteeWhen requesting important repairs within 10 days of purchase Exchange or RepaymentRequesting important repairs within 1 month since purchase date Exchange or Repair Free of ChargeAn important repair is needed after 1 month of exchange Exchange or Repair Free of ChargeWhen it is impossible to exchange within 1 month RepaymentPossible RepairsThe same problem occurs 3 times Repair Free of Charge Charged RepairThe same problem occurs 4 times Exchange or Repayment Charged Repair5 problems in all different partsImpossible RepairsWhen the manufacturer has lost the product in which the customer has requested for a repair Exchange or Repayment Exchange after depreciation of the fixed price.When it is impossible to repair within 1 monthImpossible to exchange RepaymentExchange after adding 10% to the depreciated price of the fix price (the highest price-purchased price).Service Center Information
BIP-600075Charged Service1. If it is not a default, it will be charged when requesting for after-sales service. - Service request due to inappropriate use of the customer - Loss of a PIN number - Use of programs that might effect the program (over-clock, forceful changes in the input of the system, personal developments)2. Default due to a mistake on the part of the customer - Default due to inappropriate or careless use of the product (dropping, submersion under water, shock, damage, unreasonable operations, etc). - Default due to a repair or unauthorized technician. - Default caused intentionally or by carelessness of the customer. - Default due to the use of fraudulent parts or components.3. Other cases - Default due to nature (fire, damage due to sea wind, flood damage, etc.). - Expendable parts have exhausted there life (batteries, antenna, or other component parts).4. Regulations of treatment after charged service - If the same default occurs on the part that had been repaired within a 2 months(60 days) period, it will be provided with free of charge repair service.There will be no returning of goods orrepayment upon the following situation Removal of the sealing of the product if it had been sealed. If the product has been damaged due to careless use by the customer or due to a natural disaster (floods, rain, fire, etc.). Loss of product or other components (CD, diskette, manual, connecting cables, etc). Damage to the product after 10 days of purchase, the product will either be exchanged or provided with after-sales service (note, returning of goods or repayment is not allowed).Service Center Information
76 BIP-6000 ManualWarranty CertificateThank you for purchasing a product from Bluebird Soft Inc. If a circumstance arises where you lose a receipt or the certificate of guarantee, then the term of guarantee will be calculated 3 months (certified by the number of the manufacture, a certificate of inspection) after the date of manufacture. In case of accessories (such as batteries), only those that match the sales list managed by the service center will be eligible for customer service. A repair or an exchange of batteries that does not match the sales list of the service center due to the carelessness of the customer will be fully charged.Warranty1. Bluebird Soft Inc. (hereinafter referred to as Bluebird) provides the warranty service for its products in compliance with the regulations on compensation for damage of customer.2. Upon receiving a notification on a defect of its product within the range of warranty during the warranty period, Bluebird will repair or replace the defective product according to its warranty policy.3. If the defective product within the range of warranty is not repairable or replaceable, Bluebird shall refund the purchasing price within a designated period from the date of receiving a notice of defect.4. Bluebird assumes no responsibility for repairing, replacement or refund until it receives the defective product from the customer. The replacement shall be equivalent to a new product in the aspect of performance.5. Warranty of Bluebird is valid in the countries where the Bluebird products are distributed by Bluebird. (Contract for additional warranty service like field service)6. Bluebird products may contain the recycled products, components or materials equivalent to new products in the aspect of performance.7. This warranty is applied to software products only when the programming commands are not executed. Bluebird does not guarantee interruption-free or error-free performance.Name of Product PDAName of Model BIP-6000Date of PurchaseManufacture NumberPlace of PurchaseTerm of Guarantee 1 year from purchase
2BIP-6000 ManualBluebird constantly strives to bring utmost satisfaction to all our customers.Hours Mon.- Fri. : 9:30 A.M. ~ 6:30 P.M.(GMT Time: +9 Hours)We are not open on Saturday, Sundays and National Holidays.Address : Customers service center, SSang-young IT twintower B 703, Sangdaewon-dong 442-5, Joongwon-gu, Sungnam-si, Keonggi-do, KoreaCustomers Service Center

Navigation menu