Axxcelera Broand Wireless EX-F058 AB-Access EXTENDER User Manual User Installation Manual part 1

Axxcelera Broadband Wireless, Inc. AB-Access EXTENDER User Installation Manual part 1

User Installation Manual part 1

Internal DRAFT CopyDocument Number: ABA-U-NII-PIM-3 (part1 – chapters 1 to 6)May 2001 AB-ACCESSSYSTEMU-NII PRODUCT INSTALLATION MANUALfor Subscriber Units, Base Stations, Access Pointsand AB-Access Extender Units
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 i PrefaceAB-Access™ System technology enables high-speed, broadband Internet access for fast datatransmission, full streaming video, real-time video conferencing, and web surfing. AdaptiveBroadband’s wireless point-to-multipoint and point-to-point solutions (AB-Access Extender) forfixed networks enables our customers to easily leap-over existing infrastructure, making theinitial investment significantly lower than that required for wired alternatives.Adaptive Broadband’s, patent pending, Packet-on-Demand technology delivers up to 10 timesthe effective Internet data throughput of existing network configurations. Our technologyprovides a last-mile solution, when deployed between networks and business/residential Internetusers. AB-Access System’s low-cost, wireless infrastructure means that a complete network canbe installed in days or weeks, instead of the typical months or years. Since AB-Accessarchitecture is highly scalable, our customers’ wireless network can grow as quickly as theirbusiness grows or as bandwidth needs evolve.This manual explains how to install the U-NII AB-NetAccess software and perform networkmanagement tasks using GUI-based applications (the AB-NetAccess client software). Thissoftware can run on any IP client on your network and is controlled by the main ElementManagement System (EMS) application, the AB-NetAccess server software, which resides on asingle server on your IP network.The main tasks covered in this manual are configuring and managing network elements, such asBase Stations, Subscriber Units, Access Points, AB-Access Extender Units, Anchor Switches,and Control Servers. Definitions of all the terms and abbreviations used in this manual can befound in the Glossary at the end of this manual.Proprietary NoticeThe information contained within this manual was originated by and is the property of AdaptiveBroadband Corporation. Adaptive Broadband Corporation reserves all patent proprietary design,manufacturing, reproduction use, and sales rights thereto, and to any articles disclosed therein,except to the extent rights are expressly granted to others. The foregoing does not apply tovendor proprietary parts. To allow for the introduction of design improvements, specificationsare subject to change without notice.Intended AudienceThis guide is aimed at qualified AB-Access System installers. Installers should have experiencein radio equipment installations and aspects of hardware and software networks. Installers forAB-Access Extender should be professionally qualified to install radio equipment.AB-ACCESS SYSTEM PREFACE
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 iiRelated DocumentationFor more information, refer to one or more of the following documents:• AB-Access U-NII Configuration & User’s Guide – Covers AB-Access components,architectures, configuration, and troubleshooting• AB-Access U-NII System Functional Specification – Lists the specifications of the variouscomponents of an AB-Access network• AB-Access U-NII Product Installation Manual – Explains how to install AB-AccessSubscriber Units and Base Stations• AB-Access Command Line Interface (CLI) Manual – Describes configuration, operational,and diagnostic capabilities for Subscriber Units and Base Stations.• AB-Access Software Release Notes – Describes updates and changes to the latest softwareand known product issues.Customer Documentation Questions/CommentsAdaptive Broadband’s Technical Publications Department is constantly reviewing its AB-Access System(s) documentation to make the information as clear, accurate, and user-friendly aspossible. We would like to receive any comments or questions you have about this manual.Please send an e-mail to: techpubs@adaptivebroadband.com with your views on anything in thismanual that you think needs to be clarified or structured differently. Additionally, please let usknow if you found this manual useful and its information easy to understand.NoticeWhile every reasonable effort has been made to ensure the accuracy of this manual, productimprovements may result in minor differences between the manual and the product shipped toyou. If you have any questions or need an exact specification for a product, please contactAdaptive Broadband’s Customer Service Team at our toll free number: TBD.In addition, documentation updates can often be found on our Web site at:www.adaptivebroadband.com.Adaptive Broadband Corp.TBD: New Tech Pubs Address, Phone and FAX information to be insertedUSATel: TBDFAX: TBDCopyright 2001 Adaptive Broadband Corp. AB-ACCESS SYSTEM ADAPTIVE BROADBAND PRODUCT WARRANTY
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 iiiProduct Manufactured by ADAP:a. Products manufactured by ADAP are warranted against defects in material andworkmanship for a period of one (1) year from date of delivery as evidenced by ADAP'spacking slip or other transportation receipt.b. ADAP's sole responsibility under this warranty will be to either repair or replace, at itsoption, any component which fails during the applicable warranty period because of a defectin material or workmanship, provided Buyer has promptly reported same to ADAP inwriting. All replaced products and parts will become ADAP's property.c. ADAP will honor the warranty at the repair facility designated by ADAP. It is Buyer'sresponsibility to return, at its expense, the allegedly defective product to ADAP. Buyermust obtain a Return Material Authorization (RMA) number and shipping instructions fromADAP prior to returning any product under warranty. Transportation charges for the returnof the product to Buyer will be paid by ADAP within the United States. For all otherlocations, the warranty excludes all costs of shipping, customs clearance and other relatedcharges. If ADAP determines that the product is not defective within the terms of thiswarranty, Buyer will pay ADAP all costs of handling, transportation and repairs at the thenprevailing repair rates.d. All the above warranties are contingent upon proper use of the product. These warrantieswill not apply (i) if adjustment, repair, or product or parts replacement is required because ofaccident, unusual physical, electrical or electromagnetic stress, neglect, misuse, failure ofelectric power, environmental controls, transportation, failure to maintained properly orotherwise in accordance with ADAP specifications, or abuses other than ordinary use; (ii) ifthe product has been modified by Buyer or has been repaired or altered outside ADAP'srepair facility, unless ADAP specifically authorizes such repairs or alterations in eachinstance; or (iii) where ADAP serial numbers, warranty data or quality assurance decalshave been removed or altered.e. No person, including any system provider, agent or representative of ADAP is authorized toassume for ADAP any other liability on its behalf except as set forth herein. If any paymentis due ADAP for services performed hereunder, it will be subject to the same payment termsas the original purchase.Products Manufactured By Others:For products not manufactured by ADAP, the original manufacturer's or licensor’s warranty willbe assigned to Buyer to the extent permitted by the manufacturer or licensor and is in lieu of anyother warranty, expressed or implied. For warranty information on a specific product, a writtenrequest should be made to ADAP.All Products:
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 ivTHE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE INLIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES, OBLIGATIONS, ANDLIABILITIES ON THE PART OF ADAP. EXCEPT FOR THE EXPRESS WARRANTIESSTATED HEREIN, ADAP DISCLAIMS ALL WARRANTIES ON PRODUCTSFURNISHED HEREUNDER, INCLUDING, WITHOUT LIMITATION, ALL IMPLIEDWARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULARPURPOSE. ADAP WILL HAVE NO RESPONSIBILITY FOR ANY PARTICULARAPPLICATION MADE OF ANY EQUIPMENT. Any description of equipment, whether inwriting or made orally by ADAP or its agents, specification sheets, models, bulletins, drawings,or similar materials used in connection with Buyer’s order are for the sole purpose of identifyingthe equipment and will not be construed as an express warranty. Any suggestions by ADAP orits agents regarding use, application or suitability of the equipment will not be construed as anexpress warranty. No warranties may be implied from any course of dealing or usage of trade.Buyer agrees that the exclusion of all warranties, other than those expressly provided herein, isreasonable.Additional Terms:All transactions between ADAP and Buyer and all matters related to them are and will begoverned solely by ADAP’s Standard Terms and Conditions of Sale as may be in effect fromtime to time, unless otherwise expressly agreed to by ADAP in advance and in writing.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 vPRODUCT RETURN PROCEDUREIt is a requirement of Adaptive Broadband Corporation that any product returned for repair orreplacement must first be authorized by Adaptive Broadband and assigned a Return MaterialAuthorization (RMA) number. The repair site will not repair or replace any defective unitwithout an RMA number.To receive authorization to return a defective product and obtain an RMA number, call AdaptiveBroadband’s Technical Support at our toll free number: TBD.AB-ACCESS SYSTEM PRODUCT RETURN PROCEDURE
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 viPLEASE READ THESE SAFETY PRECAUTIONS!RF Energy Health HazardThe radio equipment described in this guide uses radio frequency transmitters. Although thepower level is low, the concentrated energy from a directional antenna may pose a health hazard.Do not allow people to come in close proximity to the front of the antenna while thetransmitter is operating.Protection from LightningArticle 810 of the US National Electric Department of Energy Handbook 1996 specifies thatradio and television lead-in cables must have adequate surge protection at or near the point ofentry to the building. The code specifies that any shielded cable from an external antenna musthave the shield directly connected to a 10 AWG wire that connects to the building groundelectrode.FCC Notice, USAThe AB-Access Subscriber Unit complies with Part 15 of the FCC rules. Operation is subject tothe following two conditions:• This device may not cause harmful interference.• This device must accept any interference received including interferencethat may cause undesired operation.This device is specifically designed to be used under Part 15, Subpart E of the FCC Rulesand Regulations. Any unauthorized modification or changes to this device without theexpress approval of Adaptive Broadband Corporation may void the user’s authority tooperate this device. Furthermore, this device is intended to be used only when installed inaccordance with the instructions outlined in this manual. Failure to comply with theseinstructions may also void the user’s authority to operate this device and/or themanufacturer’s warranty
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 viiConditions specific to AB-Access Extender:AB-Access Extender complies with Part 15 of the FCC rules. The device is specifically designedto be used under Part 15, Sub-part E of the FCC rules and regulations. Operation is subject tofollowing conditions:• The device to utilize a fixed mount antenna, for use on a permanent outdoor structure.• The device to be installed by qualified installation/deployment personnel, and a minimum of1.5 meters of separation must exist between the device and persons, when the device isoperating.• The device installers and operators should be aware of the transmitter operating conditions,specified in the AB-Extender installation manual and other associated user documentation, aswell as the antenna co-location requirements of Part 1.1307 (b) (3), of FCC rules, pertainingto RF exposure.• The device may not cause harmful interference.• The device must accept interference received, including interference that may causeundesired operation.The device is intended to be used only when installed in accordance with instructions outlined inthis manual. Failure to comply with these instructions may void the user's authority to operatethis device and/or the manufacturer's warranty. Furthermore, any unauthorized modification orchanges to this device without the express approval of Adaptive Broadband Corporation mayalso void the user's authority to operate this device.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 viii1 AB-Access Product Overview........................................................................................1-11.1 AB-Access System.......................................................................................................1-11.2 AB-Access Network.....................................................................................................1-11.3 System Components.....................................................................................................1-11.3.1 AB-Access System Architecture..........................................................................1-21.3.2 Base Station Function...........................................................................................1-31.3.3 Subscriber Unit Function......................................................................................1-31.3.4 EMS Function.......................................................................................................1-41.3.5 System Configuration Selection...........................................................................1-42 Getting Started ...............................................................................................................2-12.1 Skills Required .............................................................................................................2-12.2 Information Needed From Your Service Provider.......................................................2-12.3 Required Tools and Equipment....................................................................................2-22.4 Unpacking the Equipment............................................................................................2-22.5 Performing A Site Survey ............................................................................................2-42.5.1 What You Need...................................................................................................2-42.5.2 Access Point Locations ........................................................................................2-42.5.3 Selecting An Access Point ...................................................................................2-62.5.4 AB-Access Extender Locations ...........................................................................2-73 Base Station Installation................................................................................................3-13.1 System Overview..........................................................................................................3-13.2 Access Points................................................................................................................3-23.3 AB-Access Extender Units...........................................................................................3-23.4 Anchor Switch..............................................................................................................3-23.5 Control Server ..............................................................................................................3-33.6 Access Panel.................................................................................................................3-43.7 A Note On Cabling.......................................................................................................3-53.8 Software Consideration................................................................................................3-54 Server and Switch Installation......................................................................................4-14.1 Before You Start...........................................................................................................4-14.1.1 Information Required ...........................................................................................4-14.1.2 Extra Equipment Required...................................................................................4-14.1.3 Optional Equipment .............................................................................................4-14.2 Unpacking The Equipment...........................................................................................4-14.2.1 Anchor Switch......................................................................................................4-24.2.2 Control Server ......................................................................................................4-24.3 Installing The Equipment .............................................................................................4-24.3.1 Position The Equipment .......................................................................................4-24.3.2 Making Up Connecting Cables ............................................................................4-24.3.3 Connecting The Equipment..................................................................................4-34.4 Base Station Access Panel Installation.........................................................................4-44.4.1 Access Panel Installation Steps............................................................................4-5AB-ACCESS SYSTEM Table of Contents
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 ix4.4.2 Powering On The Equipment...............................................................................4-65 Access Point Installation................................................................................................5-15.1 Before You Start...........................................................................................................5-15.2 Information Required ...................................................................................................5-15.2.1 Equipment Required.............................................................................................5-25.3 Access Points................................................................................................................5-25.4 Indoor Patch Panel .......................................................................................................5-35.5 Installing The Equipment .............................................................................................5-35.5.1 Overview ..............................................................................................................5-45.5.2 Installing The Mounting Poles .............................................................................5-45.5.3 Installing On An Antenna Mast ...........................................................................5-45.5.4 Installing On Brick Or Masonry...........................................................................5-55.5.5 Installing On A Wall With Wood Siding.............................................................5-55.6 Mounting The Outdoor Access Points .........................................................................5-65.6.1 Installing the Access Panel...................................................................................5-75.6.2 Installing The Interconnect Cables.......................................................................5-75.6.3 Grounding The System.......................................................................................5-126 AB-Access Extender Installation ..................................................................................6-16.1 Before You Start...........................................................................................................6-16.2 Information Required ...................................................................................................6-16.2.1 Equipment Required.............................................................................................6-16.3 AB-Access Extender....................................................................................................6-26.4 Indoor Patch Panel .......................................................................................................6-36.5 Installing The Equipment .............................................................................................6-36.5.1 Overview ..............................................................................................................6-36.5.2 Installing The Mounting Poles .............................................................................6-36.5.3 Installing On An Antenna Mast ...........................................................................6-46.5.4 Installing On Brick Or Masonry...........................................................................6-46.5.5 Installing On A Wall With Wood Siding.............................................................6-56.6 Mounting The Outdoor AB-Access Extender..............................................................6-56.6.1 Installing the Access Panel...................................................................................6-76.6.2 Installing The Interconnect Cables.......................................................................6-76.6.3 Grounding The System.......................................................................................6-127 Subscriber Unit Installation ............................................... Error! Bookmark not defined.7.1 Installation Overview .................................................... Error! Bookmark not defined.7.2 Installing Mounting Pole .............................................. Error! Bookmark not defined.7.2.1 Installing on a Brick or Masonry Wall.................. Error! Bookmark not defined.7.2.2 Installing on a Wall with Wood Siding................. Error! Bookmark not defined.7.2.3 Installing on an Antenna Mast .............................. Error! Bookmark not defined.7.3 Installing the Outdoor Subscriber Unit ......................... Error! Bookmark not defined.7.4 Preparing The Indoor Junction Box .............................. Error! Bookmark not defined.7.5 Installing the Interconnect Cable .................................. Error! Bookmark not defined.7.5.1 Routing the Interconnect Cable............................. Error! Bookmark not defined.7.5.2 Preparing the Interconnect Cable.......................... Error! Bookmark not defined.7.5.3 Connecting to the Outdoor Subscriber Unit TransceiverError! Bookmark notdefined.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 x7.5.4 Connecting to the Indoor Junction Box................. Error! Bookmark not defined.7.6 Grounding The System.................................................. Error! Bookmark not defined.7.6.1 Installing A Grounding Rod.................................. Error! Bookmark not defined.7.6.2 Grounding the Outdoor Subscriber Unit ............... Error! Bookmark not defined.7.6.3 Grounding the Indoor Junction Box...................... Error! Bookmark not defined.7.6.4 Assembling and Mounting the Junction Box ........ Error! Bookmark not defined.8 Indoor Junction Box............................................................ Error! Bookmark not defined.8.1 ATM Cross-Over Cable ................................................ Error! Bookmark not defined.8.2 FVC DB-9 To RJ-45 Converter .................................... Error! Bookmark not defined.9 Testing the System............................................................... Error! Bookmark not defined.9.1 Introduction................................................................... Error! Bookmark not defined.9.2 Equipment Required...................................................... Error! Bookmark not defined.9.3 Testing........................................................................... Error! Bookmark not defined.9.3.1 Connecting Test PC............................................... Error! Bookmark not defined.9.4 Configure The IP Address............................................. Error! Bookmark not defined.9.5 Using the RSSI Interface for RF Alignment ................. Error! Bookmark not defined.9.6 Display The Security Page ............................................ Error! Bookmark not defined.9.7 Optimize The Antenna Alignment ................................ Error! Bookmark not defined.10 Specifications ................................................................... Error! Bookmark not defined.10.1 Subscriber Unit Antenna............................................... Error! Bookmark not defined.10.2 Access Point Antenna ................................................... Error! Bookmark not defined.10.3 AB-Access Extender Antenna....................................... Error! Bookmark not defined.Figure 10-3 Typical EX Antenna Pattern.................................. Error! Bookmark not defined.TBD: Update all section and figure numbers from here on forwardError! Bookmark notdefined.10.4 Modem Specifications...................................................... Error! Bookmark not defined.10.5 Environmental Specifications........................................... Error! Bookmark not defined.10.5.1 Temperature/Humidity Operation.............................. Error! Bookmark not defined.10.5.2 Grounding................................................................... Error! Bookmark not defined.10.5.3 Electrical Specifications............................................. Error! Bookmark not defined.10.5.4 Power Consumption................................................... Error! Bookmark not defined.10.5.5 Distance Limitations................................................... Error! Bookmark not defined.10.5.6 Physical Specifications............................................... Error! Bookmark not defined.10.6 Cable Specifications.......................................................... Error! Bookmark not defined.10.6.1 Outdoor Cable Specifications..................................... Error! Bookmark not defined.10.7 RJ-45 Plug Specifications.................................................. Error! Bookmark not defined.11 Glossary & Acronyms..................................................... Error! Bookmark not defined.11.1 Acronyms/Abbreviations............................................... Error! Bookmark not defined.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 xiFigure 1-1 AB-Access Typical Deployment................................................................................1-2Figure 1-2 AB-Access Typical Network Architecture................................................................1-3Figure 2-1 Outdoor Subscriber Unit Components .......................................................................2-3Figure 2-2 Access Point Locations.............................................................................................2-5Figure 2-3 Aligning the Compass and Map ...............................................................................2-6Figure 2-4 Selecting an Access Point.........................................................................................2-7Figure 3-1 Base Station Overview ...............................................................................................3-1Figure 3-2 Outdoor Access Point and Mounting Pole ................................................................3-2Figure 3-3 Anchor Switch Front Panel .......................................................................................3-2Figure 3-4 Dell 2450 Control Server Rear Panel........................................................................3-3Figure 3-5 Access Panel..............................................................................................................3-4Figure 4-1 ATM Cross-Over Cable.............................................................................................4-3Figure 5-1 Diagram of Six Access Points for 360 degree Coverage...........................................5-1Figure 5-2 Outdoor Access Point Components...........................................................................5-3Figure 5-3 Access Panel used as Patch Panel .............................................................................5-3Figure 5-4 Mounting Pole Installed on Pole or Antenna Mast ...................................................5-4Figure 5-5 Mounting Pole Installation ........................................................................................5-5Figure 5-6 Mounting Pole on Clapboard Siding.........................................................................5-5Figure 5-7 Mounting Parts for an Outdoor Access Point............................................................5-6Figure 5-8 Access Point Rear View............................................................................................5-6Figure 5-9 Tilt Bracket................................................................................................................5-7Figure 5-10 Access Point with Mounted Tilt Bracket ................................................................5-7Figure 5-11 Grommet Location - Underside of Access Point.....................................................5-8Figure 5-12 Outdoor Transceiver End of the Interconnect Cable with Cable Preparation.........5-9Figure 5-13 Outdoor Transceiver End of the Interconnect Cable with Shielding.......................5-9Figure 5-14 Interconnect Cable Installation to Outdoor Access Point - Bottom View.............5-11Figure 5-15 Access Panel showing Connections to Access Point............................................5-11Figure 5-16 Ground Connections to Access Point Transceiver ................................................5-12Figure 5-17 Mounting Pole with Ground Lug...........................................................................5-13Figure 6-1 Outdoor AB-Access Extender Components..............................................................6-3Figure 6-2 Access Panel used as Patch Panel .............................................................................6-3Figure 6-3 Mounting Pole Installed on Pole or Antenna Mast ...................................................6-4Figure 6-4 Mounting Pole Installation ........................................................................................6-5Figure 6-5 Mounting Pole on Clapboard Siding.........................................................................6-5Figure 6-6 Mounting Parts for an Outdoor AB-Access Extender...............................................6-6Figure 6-7 AB-Access Extender Rear View ...............................................................................6-6Figure 6-8 Tilt Bracket................................................................................................................6-6Figure 6-9 AB-Access Extender with Mounted Tilt Bracket......................................................6-6Figure 6-10 Grommet Location - Underside of AB-Access Extender........................................6-7Figure 6-11 Outdoor Transceiver End of the Interconnect Cable with Cable Preparation.........6-9Figure 6-12 Outdoor Transceiver End of the Interconnect Cable with Shielding.......................6-9AB-ACCESS SYSTEM LIST OF FIGURES
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 xiiFigure 6-13 Interconnect Cable Installation to Outdoor AB-Access Extender - Bottom View6-11Figure 6-14 Access Panel showing Connections to AP/EX.....................................................6-11Figure 6-15 Ground Connections to AB-Access Extender Transceiver...................................6-12Figure 6-16 Mounting Pole with Ground Lug...........................................................................6-13Figure 7-1 AB-Access Subscriber Unit Installation Overview.... Error! Bookmark not defined.Figure 7-2 Mounting Pole Drill Locations.................................. Error! Bookmark not defined.Figure 7-3 Mounting Pole Installation Using Expansion Sleeves and Lag BoltsError!Bookmark not defined.Figure 7-4 Mounting Pole on Clapboard Siding......................... Error! Bookmark not defined.Figure 7-5 Mounting Pole Installed on Pole or Antenna Mast .... Error! Bookmark not defined.Figure 7-6 Outdoor Subscriber Unit Mounted on Wall................ Error! Bookmark not defined.Figure 7-7 Junction Box Wall Mount (Face Plate and PCB Removed)Error! Bookmark notdefined.Figure 7-8 Interconnect Cable Routing Solutions........................ Error! Bookmark not defined.Figure 7-9 Grommet Location -- Underside of Subscriber Unit.. Error! Bookmark not defined.Figure 7-10 Outdoor Subscriber Unit of the Interconnect Cable with Cable PreparationError!Bookmark not defined.Figure 7-11 Outdoor Subscriber Unit End of the Interconnect Cable with ShieldingError!Bookmark not defined.Figure 7-12 Interconnect Cable Installation to Subscriber Unit -- Bottom ViewError!Bookmark not defined.Figure 7-13 Interconnect Cable Connections to Indoor Junction BoxError! Bookmark notdefined.Figure 7-14 Ground Connections for Subscriber Unit................. Error! Bookmark not defined.Figure 7-15 Mounting Pole with Ground Lug.............................. Error! Bookmark not defined.Figure 7-16 Indoor Junction Box Ground Connection................. Error! Bookmark not defined.Figure 8-1 Indoor Junction Box (Wall Plate Enclosure).............. Error! Bookmark not defined.Figure 8-2 Indoor Junction Box Inside........................................ Error! Bookmark not defined.Figure 8-3 ATM Cross-Over Cable.............................................. Error! Bookmark not defined.Figure 8-4 DB-9 To RJ-45 Converter .......................................... Error! Bookmark not defined.Figure 9-1 Security Screen........................................................... Error! Bookmark not defined.Figure 9-2 RSSI Sample Web Page ............................................. Error! Bookmark not defined.Figure 10-1 Typical SU Antenna Pattern..................................... Error! Bookmark not defined.Figure 10-2 Typical AP Antenna Pattern...................................... Error! Bookmark not defined.Figure 10-3 Typical EX Antenna Pattern...................................... Error! Bookmark not defined.Figure 10-4 Powering SU through Junction Box ......................... Error! Bookmark not defined.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 xiii LIST OF TABLESTable 1-1 Supported AB-Access SU Configurations..................................................................1-5Table 1-2 Supported AB-Access AP Configurations..................................................................1-5Table 2-1 Required Tools and Extra Equipment..........................................................................2-2Table 2-2 Packing List ...............................................................................................................2-3Table 4-1 Required Tools and Equipment ..................................................................................4-1Table 4-2 Required Cables..........................................................................................................4-3Table 4-3 Base Station Access Panel Description.......................................................................4-4Table 5-1 Required Tools and Equipment ..................................................................................5-2Table 5-2 AP Components ..........................................................................................................5-2Table 5-3 Cable Legend for Interconnect Cable.......................................................................5-10Table 6-1 Required Tools and Equipment ..................................................................................6-1Table 6-2 EX Components..........................................................................................................6-2Table 6-3 Cable Legend for Interconnect Cable.......................................................................6-10Table 7-1 Required Tools And Equipment .................................. Error! Bookmark not defined.Table 7-2 Required Tools and Equipment ................................... Error! Bookmark not defined.Table 7-3 Required Tools and Equipment .................................. Error! Bookmark not defined.Table 7-4 Required Tools and Equipment ................................... Error! Bookmark not defined.Table 7-5 Required Tools and Equipment ................................... Error! Bookmark not defined.Table 7-6 Required Tools and Equipment ................................... Error! Bookmark not defined.Table 7-7 Cable Legend for Interconnect Cable........................... Error! Bookmark not defined.Table 7-8 Required Tools and Equipment ................................... Error! Bookmark not defined.Table 8-1 Cable Legend - Junction Box Interconnect Cable ....... Error! Bookmark not defined.Table 9-1 RSSI Link Validity ...................................................... Error! Bookmark not defined.Table 10-1 Subscriber Unit Antenna Specifications.................... Error! Bookmark not defined.Table 10-2 Access Point Antenna Specifications......................... Error! Bookmark not defined.Table 10-3 AB-Access Extender Antenna Specifications............ Error! Bookmark not defined.Table 10-4 Modem Specifications................................................ Error! Bookmark not defined.Table 10-5 Environmental Specifications.................................... Error! Bookmark not defined.Table 10-6 SU, EX and AP Power Consumption......................... Error! Bookmark not defined.Table 10-7 SU Weight and Size................................................... Error! Bookmark not defined.Table 10-8 Outdoor Cable Specifications.................................... Error! Bookmark not defined.Table 10-9 RJ-45 Plug Specifications.......................................... Error! Bookmark not defined.AB-ACCESS SYSTEM LIST OF TABLES
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 1-11 AB-Access Product Overview1.1 AB-Access SystemThe Adaptive Broadband AB-Access System is a broadband, fixed, wireless access network forInternet, data, video, and voice applications. AB-Access can enhance or replace existingnetworks, wired or wireless, or be used to develop new networks. The AB-Access System offers:• Point-to-Multipoint (PMP) Wireless Access Network• Point-to-Point (PTP) Wireless Access Network [AB-Access Extender]• End-to-End Connectivity• Spectrum Efficiency per Offered Load• Powerful, Flexible Elements.1.2 AB-Access NetworkThe AB-Access network consists of wireless 25 Mbps cells similar in topology to the cellularnetworks of today. AB-Access networks are designed for rapid and easy deployment, andconstructed from a number of Base Stations deployed in a conventional cellular pattern.Deployment can vary from a number of small island sites to complete coverage of a chosengeographical area. AB-Access Extender allows these cell sites to be linked together with high-speed, long range, point-to-point connections.1.3 System ComponentsThe AB-Access System is comprised of the following five major components:• Subscriber Unit (SU) – Located at customer premises and provides either ATM orstandard IP over Ethernet connectivity.• Access Point (AP) - The Access Point is the cornerstone component of the Base Station.The AP is the interface between the Service Provider’s terrestrial network and thewireless fabric. Each AP has the capability to provide network service at the Physical,Data Link, and Network Layers of the OSI reference model.• AB-Access Extender (EX) - The AB-Access Extender is the inter-Base Station linkingcomponent. The EX is the interface between the Service Provider’s terrestrial networkand the wireless PMP fabric. Each EX has the capability to provide network service atSECTION 1 AB-Access Product Overview
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 1-2the Physical, Data Link, and Network Layers of the OSI reference model. Each EX canprovide ATM or Ethernet backhaul.• Anchor Switch (AS) - An ATM (or Ethernet) Anchor Switch in each Base Station isused to multiplex the traffic from all APs onto a Backhaul port.• Control Server (CS) - The Control Server is a reliable server running the Linux OS. Itprovides a number of functions including: configuration, authentication, set-up ofmanagement PVCs, and support of the Element Management System (EMS).• Element Management System (EMS) – A GUI based application suite that allowsadministrators to configure, control, and monitor all components of the system.1.3.1 AB-Access System ArchitectureFigures 1-1 and 1-2 show an AB-Access System’s typical deployment and network architecture.Figure 1-1 AB-Access Typical DeploymentATMElementManagementServer 4400 WIN NT 4.0EthernetSUTypically 6 AccessPoints per Base StationUp to 16 (254) SubscriberUnits per Access PointRouterISP RouterSUBase StationControlServer2450LinuxLiATM SwitchATM25DS3 /OC3EthernetATM25AP AP APSU - Subscriber UnAP - Access PointCS - Control ServeBS - Base Station
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 1-3Figure 1-2 AB-Access Typical Network ArchitectureTBD: Add AB-Access Extender to this diagram1.3.2 Base Station FunctionThe Base Station enables wireless communications between the Subscriber Units and the WideArea Network (WAN). Base Station elements include:• Access Point• AB-Access Extender• Access Panel (same function as Junction Box)• Anchor Switch• Control Server• Termination Point and Lightning Arrestor• 48 VDC Power Supply• Uninterruptible Power Supply (UPS) (optional).1.3.3 Subscriber Unit FunctionThe Subscriber Unit is an integrated device that mounts externally at the customer site. Thisdevice provides either ATM or standard IP over Ethernet, via 25 Mbps ATM, wirelesscommunications with the Base Station. Subscriber Unit elements include:• Antenna• Radio/Transceiver• Modem• MAC (Media Access Controller)• Network Interface• Internal Junction Box
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 1-4• Cabling.1.3.4 EMS FunctionThe central Element Management System (EMS), which system administrators access via aGUI-based application suite (the AB-NetAccess client software), is run on a Pentium classcomputer under Windows NT. The EMS allows the user to configure, control, and monitor allcomponents of the AB-Access System. EMS software elements include:• SQL Database• Java GUI Interface• CORBA Object Infrastructure.1.3.5 System Configuration SelectionBefore installing a new unit or upgrading a unit, the network manager must know whatconfiguration option to use. This is important for both static and dynamic installations. Theupgrade process will place a unit in a certain state. The state of this unit will be very importantdepending upon whether the unit is already being used in production or about to be put into use.Units in production will need to be upgraded and placed back into production using theconfiguration currently in place. New units will require the proper configuration in order tocome online fast and efficiently. This whole process relies on the fact that the units areprogrammed properly.Units operating in static mode will want to retain this mode. Selecting the wrong configurationmay result in a static unit being placed in a dynamic registration mode, making it potentiallyunmanageable remotely. Similarly, upgrading a unit running in a routed topology to a bridgetopology will have a significant impact on functionality.Contained in each system software release is a file that lists the possible configuration options.The file is called “configurations” and looks similar to Tables 1-1 and 1-2. This file is split intotwo tables, one for the AP and one for the SU configurations. These tables are used todetermine which configuration the unit will be programmed in after upgrade.For the purposes of network and software configuration, the AB-Access Extender units appear asstatic point-to-point SU units. They support Ethernet or ATM wired interfaces. CLIP, RFC1483and native ATM are supported static configuration for these units. An AB-Access Extenderpoint-to-point link consists of two Extender units, a Head End Unit (“AP”) and an UpstreamSubscriber Unit (“SU”).
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 1-5 Table 1-1 Supported AB-Access SU Configurations============================================Configuration Protocol AP role System Mode Interface------------------------------------------------------------------------------------------1 CLIP terminated static Ethernet2 CLIP terminated interactive Ethernet2 RFC1483 terminated interactive Ethernet2 RFC1483 switched interactive Ethernet4 PPP switched interactive Ethernet3 CLIP terminated installation Ethernet3 RFC1483 terminated installation Ethernet3 RFC1483 switched installation Ethernet5 PPP switched installation Ethernet Table 1-2 Supported AB-Access AP Configurations============================================Configuration Protocol AP Role System Mode Interface------------------------------------------------------------------------------------------1 CLIP terminated static ATM2 CLIP terminated interactive ATM3 RFC1483 terminated interactive Ethernet2 RFC1483 switched interactive ATM2 PPP switched interactive ATM4 CLIP terminated static EthernetThe first column in the Tables above refers to a configuration number. This number will be usedas a parameter to the upgrade process. The second column identifies the protocol or networktopology. Routed topologies will use the CLIP protocol, bridged will use the RFC1483 protocol,
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 1-6and PPP topologies will use the PPP protocol. The column titled “AP Role” is used to specifywhether the AP will terminate PVCs from the SU or switch them through to another terminationpoint. This is only pertinent to the AP upgrade. The fourth column, “System Mode”, refers tohow the unit will act in the network. A unit in static mode will not try to register with theElement Management System but will instead use the configuration files found in the Flash filesystem. A unit in interactive mode will automatically try to register with EMS (dynamically) viathe AP with the strongest RF signal it can detect. Installation mode, used for SUs only, placesthe SU is a mode which will ultimately allow it to register dynamically, but upon first boot, theunit requires manual intervention to complete its RF alignment. The last column, “Interface”defines the type of terrestrial interface the unit will use after reboot. This is important to notesince improper configuration selection will change the terrestrial interface type. This may makethe unit appear unreachable after reboot.With every release, be sure to carefully look over the configuration option file, as new optionsare occasionally added. To reset a unit to factory defaults, an AP should be upgraded toconfiguration #4 and an SU to configuration #1(reference Tables 1-1 and 1-2).For more information about configuring your AB-Access System, reference the U-NIIConfiguration and User’s Guide.Following are instructions for setting up Subscriber Units, Base Stations, AB-Access Extenderand Access Points. A Glossary of definitions and acronyms is at the end of this manual.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 2-12 Getting Started2.1 Skills RequiredThe AB-Access U-NII Product Installation procedures require some construction-relatedexperience using both power and hand tools. Answer the following questions to determinewhether you have the skills attempt the installation.• Are you comfortable working at heights?(The installation may require you to climb a ladder and work at heights depending onwhere you need to install your outdoor transceiver. Keep in mind, you will also carrytools and equipment with you to the installation site.)• Have you ever installed an RJ-45 connector to an Ethernet cable?(This is required if you are not using a standard length cable interconnect cable kitbetween the outdoor transceiver and the indoor junction box.)• Have you run telephone cable, wired a telephone jack, or connected telephone wireconnections to a punch down block?• Have you ever installed expansion shields into brick or masonry walls?(This requires drilling holes in masonry using masonry drill bits.)• Have you ever wired an electrical outlet?Although you won’t wire an outlet, you will be required to run ground wires andclamp them to an earth grounding rod or a cold water pipe.If you can perform all the above tasks, then you should be able to install the AB-Access System.If you are unsure of your ability to perform these tasks, contact a more qualified installer, viayour local AB-Access System provider.2.2 Information Needed From Your Service ProviderYour service provider should have supplied you with the following information. Please contactyour service provider before commencing installation, if you do not have all of this information:• Locations of any local Access Points, which you should be able to connect to.• The IP address of your Subscriber Unit.• IP address and subnet mask, which you need to configure a Test PC. This is so youcan check to see if your SU is working, align your outdoor transceiver correctly, andconfirm that you can connect to your service provider.• Any required static configuration for AB-Access Extender units e.g. IP addresses,channels to be used etc.SECTION 2 Getting Started
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 2-22.3 Required Tools and EquipmentThis section lists all the extra tools and equipment mentioned in this guide that you will need toperform the installation. None of the items listed in Table 2-1 are supplied with the kit, so makesure you gather everything you need before you start. Use the table below to check exactly whatyou will need (this will depend on where you are going to install the outdoor transceiver). Table 2-1 Required Tools and Extra EquipmentTBD: add tool requirement for AB-Access ExtenderTools Required Extra Equipment RequiredCompass ¼ inch grounding rodArea map with an accurate directionlegend showing magnetic north Grounding clampPhillips-head screwdriver Grounding wireFlat-head screwdriver Roll of UTP CAT 5 cableHammer or mallet #6 wood screwsPower drill Cable clip1/8 inch drill bit Anchor sleeves¼ inch masonry drill bit RJ-45 connectors (plastic bodied)3/16 inch hex (Allen) wrench 1 inch copper tapeBubble level or plumb line Ethernet Hub (10BaseT)Adjustable wrenchWire snake (if routing cable throughinterior walls) Recommend a 19” rack to hold themonitor, Element ManagementSystem, Anchor Switch, andControl Server.Crimping tool (must be specificallymatched for the RJ-45 connector used)Wire stripperSmall wire cuttersPunch down tool2.4 Unpacking the EquipmentTable 2-2 lists all the standard parts that are supplied in your AB-Access Subscriber UnitInstallation Package. Please take the time to unpack the package and check its contents againstthis list.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 2-3Figure 2-1 Outdoor Subscriber Unit ComponentsTable 2-2 Packing ListItem Quantity NotesOutdoor Subscriber Unit 1 See item 1 in Figure 2-1Mounting pole 1 See item 2 in Figure 2-1Pole clamp 1 See item 3 in Figure 2-1M6 washer 2 See item 4 in Figure 2-1M3 x M10 machine thread screws 2 See item 5 in Figure 2-1CAT-5 interconnect cable 1Power supply 1Power cord 1Indoor junction box 1
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 2-42.5 Performing A Site SurveyThis section explains how to select the best location for mounting the outdoor transceiver. Thesteps you will perform are:1. Determine which Access Points you can communicate with.2. Determine the direction of available Access Points from the house or building.3. Select an Access Point with an unobstructed Line of Sight (LOS).Attention! It is very important that you choose a CLEARLINE OF SIGHT for the placement of your Access Point Unitsand Subscriber Units.2.5.1 What You Need• Compass (or protractor).• Area map with an accurate direction legend showing magnetic north.• Access Point locations – these should be provided by your service provider.2.5.2 Access Point LocationsIf you are installing the unit without the aid of a qualified installer, you need to determine thegeneral direction of any Access Points from your house or building. You may be able to ‘see’several APs, depending on your coverage area.Attention! The following method uses a compass to find the bearing of any APs from your site. An alternative method is to use a protractor to measure the angle between North and a line to the AP from your site. This tells you the compass bearing to use when aligning your outdoor transceiver.1. On your map, mark the location of your house or building2. Mark the locations of any Access Points – these should have been supplied by yourservice provider:
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 2-5Figure 2-2 Access Point Locations3. Place the compass on the map on or near the magnetic north indicator.4. Turn the compass so that the magnetic north indicator needle aligns with the N orNorth indicator on the compass body.5. Rotate the map, keeping the compass stationary, so the map’s North Indicator alignswith the North Indicator of the compass (see Figure 2-3).Move the compass over your location on the map and read off the bearing to the AP.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 2-6Figure 2-3 Aligning the Compass and Map6. Write down the directions (compass bearings) of your Access Points. For example, inFigure 2-3, Access Point A is located northwest of the building and Access Point B islocated between north and northeast. (If you can be more accurate than this, you willget better reception when you install your outdoor transceiver.)2.5.3 Selecting An Access PointIn order for your AB-Access System to work correctly, you MUSTestablish a clear line of sight to one or more of the Access Pointsrecommended by your AB-Access System provider.1. Using the compass bearings you wrote down in the previous section, walk aroundyour building to find a suitable line of sight path to mount your outdoor transceiver –see Figure 2-4.Attention! A clear line of sight means a path unobstructed by trees,dense foliage, or other buildings.If necessary, move to an upstairs window or rooftop location to better view the surrounding areafor possible blockages in the path. Also, be sure to consider seasonal changes. A location that isunobstructed in the winter may be obstructed by foliage in the spring, summer, and autumn.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 2-7Figure 2-4 Selecting an Access PointYou should mount your outdoor Subscriber Unit as high as possible on your building, and alignit to the compass reading you have just taken. For example, the previous Figure 2-4 shows thepath to Access Point A obstructed by a cluster of trees. However, there are two possiblemounting locations for the outdoor Subscriber Unit giving a clear line of sight to Access Point B.Attention! Your outdoor transceiver has a beam width of approximately 20 degrees. You will need to be fairly accurate when aligning your transceiver to the compass bearing you wrote down earlier (the more accurate your compass readings, the better).2. If you do come up with two or more suitable locations for the outdoor SubscriberUnit, choose the one that is easiest for you to reach, when it comes to installing!2.5.4 AB-Access Extender LocationsIn order for your AB-Access Extender link to work correctly, youMUST establish a clear line of sight between the Extender AP andExtender SU.Attention! A clear line of sight means a path unobstructed by trees,dense foliage, or other buildings.Attention! Your outdoor transceiver has a beam width of approximately 10 degrees. You will need to be fairly accurate when aligning your transceiver to the compass bearing you wrote down earlier (the more accurate your compass readings, the better).TBD: Additional instructions for AB-Access Extender
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 3-13 Base Station Installation3.1 System OverviewThis section briefly describes the AB-Access hardware and software system components thatcomprise a Base Station.Figure 3-1 Base Station OverviewSECTION 3 Base Station Installation
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 3-23.2 Access PointsFigure 3-2 Outdoor Access Point and Mounting PoleA Base Station can have up to six Access Points. Each AP consists of an outdoor transceiver –the antenna and associated electronics that transmit and receive broadband wireless signals toand from Subscriber Units.3.3 AB-Access Extender UnitsA Base Station may have a number of AB-Access Extender units. Each EX consists of anoutdoor transceiver – the antenna and associated electronics that transmit and receive broadbandwireless signals to and from the EX at the other end of the backhaul link.3.4 Anchor SwitchFigure 3-3 Anchor Switch Front PanelThis is typically an Access NGI WAN Access Switch, model VSW 200E, from FVC.COM.The Anchor Switch has the following connections:• Typically, six or 12 ATM25 ports:Port 101 – firstone on the leftconnects theswitch to anATM25 card onthe ControlServer
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 3-3- Port 101 – connects the switch to an ATM25 card on the Control Server using an ATM cross-over cable.- The other ATM25 ports connect to each AP via the indoor junction box oraccess panel, using ATM cross-over cable.• Switch configuration ports:- Console Port – Connects to the COM2 port on the Control Server. This is the usualmethod for monitoring and configuring the switch. Standard serial port settings are 8,n,1no flow control.- Ethernet Port – Optionally, this can also be used to access the switch remotely. You will need to give the switch an IP address, and then configure it via a machine with an Ethernet card.Please see the V-Switch User’s Guide (supplied with the switch) for detailed information onconfiguring the switch.• (Optional) Backhaul connection – This can be via:- OC3- DS3- Multiple T1s.- AB-Access Extender3.5 Control Server Figure 3-4 Dell 2450 Control Server Rear PanelShown in Figure 3-4 is the rear of a Dell PowerEdge 2450 Control Server. It comes pre-installedwith the necessary hardware to get a Base Station up and running. It provides an interfaceEmbedded EthernetNIC InterfaceATM25 port
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 3-4between the anchor switch and the network management software. The ports on the rear panelare as follows:• ATM25 port – Connects to port 101 on the anchor switch.• COM2 port – Connects to the Console port on the anchor switch. Used for monitoring andconfiguring the switch.Attention! This is a DB-9 connector. First, plug the DB-9 to RJ-45 adapter (supplied withFVC switch) into this port, then plug a straight through patch cable from the switch intothe adapter. It is important to note that the user must use the FVC supplied serial adapter,as other adapters may not operate correctly!Please see the V-Switch User’s Guide (supplied with the switch) for detailed information onconfiguring the switch.• Mouse port• Keyboard port• Monitor port• Power connector – There may be one or three of these, depending on your model ControlServer.3.6 Access PanelFigure 3-5 Access PanelThe Access Panel provides an interface between the Anchor Switch (AS), a 48V power supply,and the APs. It includes:• Rack-mounted unit that can handle up to six APs• Connects to a redundant 48V DC power supply• RJ-45 connectors to take interconnect cables from APs• RJ-45 connectors to take ATM cross-over cables to the AS• Grounding points
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 3-5• LEDs to indicate AP status• Separate on/off switches for each AP / AB-Access Extender.3.7 A Note On CablingAttention! Most of the cabling used in the AB-Access System is CAT5. You will need to be aware of the following limits on CAT5 cable lengths:• The interconnect cable from the indoor junction box to an outdoor transceiver must be lessthan 60 meters. This is due to DC resistance loss over the distance of the cable run.• The combined length of ATM cross-over cable (from the junction box to the anchor switch)and the interconnect cable must be less than 100 meters.3.8 Software ConsiderationAs an installer, you need to know how to use a serial console to:• Configure the Permanent Virtual Circuits (PVCs) on the AS.• Check the status of communications between the AS and CS.• Check the backhaul connection.You will use a Command Line Interface (CLI) to perform any necessary configuration. Foradditional information, please see the U-NII Configuration and User’s Guide.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 4-14 Server and Switch Installation4.1 Before You StartThis part of the manual is aimed at experienced network installers. It explains how to install andconfigure a Control Server(CS) and Anchor Switch (AS), and how to get an AB-Access BaseStation up-and-running.It does not tell you how to manage an AB-Access network. This section lists the informationyou will need to know before you can install a Base Station.4.1.1 Information RequiredBefore you perform the installation, you will need to know which outdoor transceivers areconnected to which port on the indoor junction box (the Access Point (AP) installer should havemade a note of this).4.1.2 Extra Equipment RequiredBefore you perform the installation, you will need the following equipment shown in Table 4-1:Table 4-1 Required Tools and EquipmentTools Required Extra Equipment RequiredCrimping tool (must be specifically matchedfor the RJ-45 connector used) RJ-45 connectorsWire stripper Roll of CAT-5 cableSmall wire cutters Monitor and cables4.1.3 Optional EquipmentIn case of power outages, an Uninterruptible Power Supply (UPS) is optional equipment that isavailable and highly recommended for purchase, but it is not covered in this guide.4.2 Unpacking The EquipmentCarefully unpack the equipment and check the items against the following lists. You shouldhave the following items (you may also have purchased a monitor, but as this is optional and it isnot included below).SECTION 4 Server and Switch Installation
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 4-24.2.1 Anchor SwitchThe Anchor Switch is an Access NGI WAN Access Switch, model VSW 200E, fromFVC>COM. The box should contain:• Anchor Switch• V-Switch User’s Guide• Power cord• Serial port adapter.4.2.2 Control ServerThe Control Server is a Dell PowerEdge 2450. The box should contain:• Control Server.• Mouse.• Keyboard• Software installation CD-ROMs (note that all necessary software has been preinstalled)• Two power cords• Keys for accessing drive bays and internal upgrade options (see below for key locations).• Manuals, including the Dell 1 x 8 Backplane Option leaflet.4.2.2.1 Key LocationsThe keys supplied with the Control Server are located as follows:• 4300 – Behind the “4300” label on the front panel; press the label to open the hiddencompartment.• 4350 – On a hanger on the rear panel• 2450 – On a hanger on the rear panel.4.3 Installing The EquipmentThis section explains how to connect up the anchor switch, Control Server and outdoortransceivers.4.3.1 Position The EquipmentAfter unpacking all the equipment, position the anchor switch and Control Server so as tominimize the distances between them, the indoor junction box, and your power outlets. You maywant to rack mount the anchor switch and Control Server. Please see the V-Switch User’s Guide.4.3.2 Making Up Connecting CablesThe following Table 4-2 shows the various types and lengths of cable.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 4-3Table 4-2 Required CablesCable Run Cable Type No. Required ConnectorsAS port 101 toCS ATM port CAT5 1 RJ-45AS Console port toCS COM(via DB-9 to RJ-45adapter)CAT5 1 RJ-45AS ports 102, 103 etc.to indoor junction box ATMCross-over Same as number oftransceivers RJ-45 – see below forpinout4.3.2.1 ATM Cross-Over CableThe pin connections for making up an ATM cross-over cable are as follows:Figure 4-1 ATM Cross-Over Cable4.3.3 Connecting The EquipmentTo connect the equipment, proceed as follows:1. Connect from port 101 on the anchor switch to the ATM port on the rear panel of the ControlServer. Use a standard CAT5 cable with an RJ-45 connector on each end.2. Connect from port 102 on the anchor switch to the appropriate port on the access panel. Usean ATM cross-over cable with an RJ-45 connector on each end.3. Repeat step 2, using ports 103, 104, 201, 202, 203 and 204, until you have connected to allthe ‘live’ ports on the access panel.Pin12345678Pin12345678
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 4-44. Insert the DB-9 to RJ-45 adapter into the COM2 port on the Control Server. Connect fromthe Console port on the anchor switch to the DB-9 to RJ-45 adapter on the COM2 port of theControl Server.5. Connect the mouse and keyboard to the Control Server.6. Connect your monitor’s signal cable to the monitor port on the Control Server.7. Connect the power cords for the Control Server, anchor switch, indoor junction box andmonitor to AC wall outlets, but do not switch on.4.4 Base Station Access Panel InstallationThe following steps cover installing the indoor Access Panel installation. Table 4-3 gives adescription of the Access Panel and Figure 4-2 shows a photo of it. As designed, these AccessPanels exactly duplicate the circuitry of the existing wall boxes. Installation follows the samedirections. However, no punch down of the STP cable is needed on the radio side of the panel.Straight through CAT5 STP cables are used to connect the panel to the radio.The patch panel is designed to replace six wall boxes in a Base Station. The Artesyn powersupplies are to be replaced by power supplies such as Kepco’s (part #PS-RM0101-1000953) rackmounted power supply operating at 48 V - 3.6 A DC.Table 4-3 Base Station Access Panel DescriptionName Description Model # Revision # CLEI code Base StationAccess PanelAccess PanelRack Mount6 AP/EX Interfaces WB-05001 v1.00 NAFigure 4-2 Access Panel Ports
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 4-54.4.1 Access Panel Installation Steps1. At the Access Panel, be sure all power switches are set to OFF.2 Determine ports to be used on the Access Panel, and set jumpers on rear of panel to desired setting (either Ethernet or ATM). Reference the following Figure 4-3. Figure 4-3 Access Panel Jumpers3. Position Access Panel4. Plug in power supply and turn on.5. Adjust to +48VDC and turn off.6. Obtain red, black, and green 18 gauge wire. Measure and cut enough of each color to connect the Access Panel to the power supply.7. Using wire strippers, strip approximately 1/4" from one end of all three leads.8. Insert the red lead into the +48V connection and tighten with precision flat tip screwdriver.8. Insert black lead into the -48V connection and tighten with precision flat tip screwdriver.9. Insert the green lead into the ground connection and tighten with precision flat tipscrewdriver.Reference the following Figure 4-4. JumpersJumperConfiguration
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 4-6Figure 4-4 Access Panel Power Connection Wires11. Using wire strippers, strip approximately 1/2" off the other end of all three leads.12. Connect the red lead to the +48V on power supply.13. Connect the black lead to the -48V on power supply.14. Connect the green lead to ground on power supply.4.4.2 Powering On The EquipmentPower on the equipment as follows:1. Power on the anchor switch. (It will go through its startup procedure, which can take up tothree minutes.)2. Power on the monitor.3. Power on the Control Server.4. When the server has finished its startup procedure, you will see a login prompt.5. Enter the user login (root) and the system password (letmein) and press Enter. (Note text isall lower-case.)6. Turn ON the power supply.7. If any of the six-transceiver power switches are OFF, turn them ON.8. For each live transceiver, check that the yellow LED on the junction box is ON. + 48V - 48 V GROUND
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-15 Access Point Installation5.1 Before You StartThis section lists the information you need on-hand before you can install a Base Station.5.2 Information RequiredBefore you perform the installation, a site survey should have been performed by the serviceprovider. From this, you will need to know:• Number of APs to install• Where the outdoor transceivers will be mounted (antenna mast, pole or building)• Heights at which the outdoor transceivers will be mounted.• Transceiver directional information (azimuth and elevation).You will probably be installing six APs on a mast or pole, giving 360 degree coverage in 60degree sectors, as shown in Figure 5-1.Figure 5-1 Diagram of Six Access Points for 360 degree CoverageIMPORTANT – Be sure to record for future reference the MAC addressfound on the AP unit BEFORE you install it.SECTION 5 Access Point Installation
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-25.2.1 Equipment RequiredTable 5-1 lists the tools and equipment you will need to install Access Points. Table 5-1 Required Tools and EquipmentTools Required Equipment RequiredCompass and protractor ¼ inch grounding rodArea map Grounding clampPhillips-head screwdriver Grounding wireFlat-head screwdriver CAT5 cableHammer or mallet #6 wood screwsPower drill Cable clips1/8 inch drill bit Anchor sleeves¼ inch masonry drill bit RJ-45 connectors (plasticbodied)3/16 inch hex (Allen) wrenchor 10 mmBubble level or plumb lineAdjustable wrenchWire snake (if routing cablethrough interior walls)Crimping tool (must bespecifically matched for theRJ-45 connector used)Wire stripperSmall wire cuttersPunch down tool5.3 Access PointsTable 5-2 lists the main components of an Access Point.Table 5-2 AP ComponentsItem Quantity NotesOutdoor transceiver 1 See item 1 in Figure 5-2Mounting pole 1 See item 2 in Figure 5-2Pole clamp 1 See item 3 in Figure 5-2M6 washer 2 See item 4 in Figure 5-2M3 x M10 machine thread screws 2 See item 5 in Figure 5-2Grounding lug 2 See item 6 in Figure 5-2Indoor junction box 1 6-way rack-mounted unitPower supply and cord 1
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-3Figure 5-2 Outdoor Access Point Components5.4 Indoor Patch PanelFigure 5-3 shows the Base Station Access Panel used as an indoor patch panel.Figure 5-3 Access Panel used as Patch Panel5.5 Installing The EquipmentThis section explains how to install an AP transceiver onto a variety of surfaces, connect them tothe indoor junction box, and ground the system. The most likely scenario is to install sixtransceivers on a single tower or mast 60 degrees apart.AP OUTAP IN
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-45.5.1 OverviewFollowing are the installation steps you will perform:1. Install the mounting poles.2. Mount the outdoor transceivers.3. Mount the access panel.4. Ground the outdoor transceivers and access panel5. Connect the interconnect cables.5.5.2 Installing The Mounting PolesFirst install the mounting poles, on which you will mount the outdoor transceivers.Bear in mind the direction in which the transceivers will point.Attention! The mounting pole must be mounted in a vertical position. Failure to do so may result in improper alignment of the outdoor transceiver. If you need to tilt the transceiver down to avoid self-interference in a cellular-style deployment, you should use an (optional) tilt bracket.Warning! The mounting pole must be grounded. See Grounding The System in Section 5.6.3.5.5.3 Installing On An Antenna Mast1. Position the mounting pole on the antenna mast.2. Insert the U-bolts around the mast and through the holes in the mounting pole. Install awasher and nut to each side of the threaded U-bolt and hand tighten. Repeat this step for thesecond U-bolt.3. Tighten nuts equally until mounting pole is secure and cannot rotate.Figure 5-4 Mounting Pole Installed on Pole or Antenna MastTypical 2 ½ inch
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-55.5.4 Installing On Brick Or Masonry1. Place the mounting plate against the wall. Use a level or plumb line to set the mounting poleperpendicular to the ground.2. Mark the hole locations.3. Set the pole aside.4. Drill ¼ inch holes at the marked locations. Drill the holes approximately ½ inch deep.5. Insert the expansion shields into the drilled holes and tap them home.6. Align the mounting pole with the drilled holes and fix with the lag bolts.Figure 5-5 Mounting Pole Installation5.5.5 Installing On A Wall With Wood Siding1. Place the mounting plate against the wall.2. Using a level, be sure that the mounting pole is perpendicular to the ground. You may needto use spacers, as shown in Figure 5-6.3. Mark the hole locations for the drilled hole locations. Remove the mounting pole and setaside.4. Drill 1/8-inch holes in the places marked.5. Use #10 or #12 wood screws to secure the mounting pole to the wall and tighten.Figure 5-6 Mounting Pole on Clapboard Siding
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-65.6 Mounting The Outdoor Access PointsNow that you have installed the mounting pole, you are ready to install the Access Points ontothe mounting poles. Reference Figures 5-7 through 5-10. Figure 5-7 Mounting Parts for an Outdoor Access Point1. Place the outdoor Access Point on the mounting pole.2. Align the pole clamp with the mounting holes.3. Insert the mounting screws and hand tighten.4. Rotate the outdoor Access Point so it is pointing in the correct direction.5. Tighten the mounting screws. Figure 5-8 Access Point Rear ViewSerialNumberPole BraceMAC ADdress(underside)Hex Bolts (2)
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-7 Figure 5-9 Tilt Bracket Figure 5-10 Access Point with Mounted Tilt Bracket5.6.1 Installing the Access PanelYou will probably install the Access Panel in a rack, along with the anchor switch and otherassociated equipment. However, keep in mind that the access panel should be:• Located where you can easily connect to a power supply.• Close to the anchor switch.• Accessible for service and troubleshooting.• Protected from rain and extremes of temperature (it is designed for indoor use).5.6.2 Installing The Interconnect CablesFor each interconnect cable, you will need to perform the following steps.5.6.2.1 Route The Cables1. Select where the cable will enter the building from the outside.2. Determine the length of cable required. Allow three extra feet on each end to allow for strainrelief, as well as any bends and turns.Side HexBoltsTilt Bracket
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-83. Route the cable.5.6.2.2 Install the Interconnect Cables (Transceiver End)1. Remove the grommet and clamping plate from the outdoor transceiver by removing the twoscrews.Figure 5-11 Grommet Location - Underside of Access PointNOTE: The Grommet is made of a special conductive material used to complete the ground between the Access Point and Access Panel.2. Insert the cable end through the grommet clamping plate (Figure 5-11)3. Insert the cable end through the grommet. The tapered end of the grommet should beopposite the cable end.4. Strip 1 inch of insulation off the cable end. Leave 3/8 inch of shielding showing and trim thewire ends flat ½ inch from there.5. Using a piece of 1 inch squared tinned copper foil, wrap the foil around the shield/braid andsheath with the left edge aligned with the edge of the braid, as shown in the followingFigures 5-12 and 5-13.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-9Figure 5-12 Outdoor Transceiver End of the Interconnect Cable with Cable PreparationFigure 5-13 Outdoor Transceiver End of the Interconnect Cable with Shielding6. Separate the twisted pair wires and align by color code in the order listed in the followingTable 5-3.GrommetGrommetclampingplateNote directionof taperInsert wireinto channels1/2"3/8"ShieldingPin 1Tab onunderside1" square tinned copper foil - wrap the copper foil around the shield/braid and sheath with the left edge aligned with the edge of the braid.Grommet isconductiveand used tocompletethe ground
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-10Table 5-3 Cable Legend for Interconnect CablePin Color Code1 White / Orange2 Orange3 White / Green4Blue5 White / Blue6 Green7 White / Brown8Brown7. Using pin 1 as a reference, insert the individual wires into the channels of the RJ-45 connector. Each wire should penetrate the channels until flush with the connector end. The copper foil tape should extend past the casing of the RJ-45 connector by approximately ½ inch.8. When all wires are inserted into the channels in their correct order, use the crimping tool toPermanently crimp the wires to the connector. Insert the RJ-45 connector into the receptaclelocated underneath the outdoor AP. Make sure that the connector tab engages the slot in thereceptacle.9. Slide the grommet up the cable and press it into the bottom of the outdoor AP.10. Slide the grommet clamp up the cable and align the holes with the mounting holes on thebottom of the outdoor transceiver.11. Insert the two screws in the mounting holes and tighten until the grommet has a slight bulge.Be sure to tighten both screws equally so that the grommet is seated correctly.12. Secure the interconnect cable to the mounting pole with the cable clip as shown inFigure 5-14.Attention! Carefully read the instructions for the crimping tool you are using. Use the correct crimping tool for the RJ-45 connector you are using. Incorrect installation of the RJ-45 connector may result in a bad connection between the outdoor transceiver and the indoor junction box.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-11Figure 5-14 Interconnect Cable Installation to Outdoor Access Point - Bottom View5.6.2.3 Installing The Interconnect Cables to Access PanelAttention! Always Disconnect Power from wall box BEFORE inserting RJ-45 connectorinto transceiver. This prevents arcing damage from occurring.1. Install an RJ-45 connector to the junction box end of the cable, following the previous steps 6through 12.2. Plug the RJ-45 into one of the upper ports in the Access Panel junction box.Figure 5-15 Access Panel showing Connections to Access PointRJ-45 toAccess PointTransceiverGND
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-125.6.2.4 Mark the Access Point CablesAttention! Step 1 is important, and will enable the network installer to configure the system easily.1. Mark the cable with a permanent label and make a note so that the network installer knowswhich outdoor AP transceiver is connected to which port on the Access Panel junction box.5.6.3 Grounding The SystemThe AB-Access System must be properly grounded in order to protect it and the structure it isinstalled on from lightning damage. This requires:1. Grounding all the outdoor transceivers as shown in Figure 5-14.2. Grounding the Access Panel to the rack.5.6.3.1 Grounding the Outdoor Access Points1. Place the grounding rod so as to allow for the shortest possible path from the groundingcable to the outdoor Access Points.2. Drive the grounding rod into the ground at least eight inches from the ground surface.3. Attach a grounding clamp to the grounding rod. You will use this clamp to attach groundingwires for both the outdoor transceiver and indoor junction box, reference Figure 5-16.Figure 5-16 Ground Connections to Access Point Transceiver
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 5-13Attention! The grounding wire should be long enough to reach from the mounting pole to the grounding rod with 3 to 6 extra feet allowed for strain relief.4. Connect a ground lug to one end of the grounding wire.5. Remove one of the lower mounting screws of the mounting pole. Insert a screw through thegrounding lug terminal and re-install it to the mounting pole.6. Attach the grounding wire to the clamp on the grounding rod, reference Figure 5-17. If necessary, use wire staples to secure the grounding wire to the outside wall.Figure 5-17 Mounting Pole with Ground Lug7. Install a grounding wire from the junction box to the grounding rod.Ground lugwith #10 awgcopper wire
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-16 AB-Access Extender Installation6.1 Before You StartThis section lists the information you need on-hand before you can install a Base Station.6.2 Information RequiredBefore you perform the installation, a site survey should have been performed by the serviceprovider. From this, you will need to know:• Number of EXs to install• Where the outdoor transceivers will be mounted (antenna mast, pole or building)• Heights at which the outdoor transceivers will be mounted.• Transceiver directional information (azimuth and elevation).IMPORTANT – Be sure to record for future reference the MAC addressfound on the EX unit BEFORE you install it.6.2.1 Equipment RequiredTable 6-1 lists the tools and equipment you will need to install AB-Access Extender units. Table 6-1 Required Tools and EquipmentTools Required Equipment RequiredCompass and protractor ¼ inch grounding rodArea map Grounding clampPhillips-head screwdriver Grounding wireFlat-head screwdriver CAT5 cableHammer or mallet #6 wood screwsPower drill Cable clips1/8 inch drill bit Anchor sleeves¼ inch masonry drill bit RJ-45 connectors (plasticbodied)3/16 inch hex (Allen) wrenchSECTION 6 AB-Access Extender Installation
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-2or 10 mmBubble level or plumb lineAdjustable wrenchWire snake (if routing cablethrough interior walls)Crimping tool (must bespecifically matched for theRJ-45 connector used)Wire stripperSmall wire cuttersPunch down toolTBD: Update this section for AB-Access Extender6.3 AB-Access ExtenderTable 6-2 lists the main components of an AB-Access Extender.Table 6-2 EX ComponentsItem Quantity NotesOutdoor transceiver 1 See item 1 in Figure 6-2Mounting pole 1 See item 2 in Figure 6-2Pole clamp 1 See item 3 in Figure 6-2M6 washer 2 See item 4 in Figure 6-2M3 x M10 machine thread screws 2 See item 5 in Figure 6-2Grounding lug 2 See item 6 in Figure 6-2Indoor junction box 1 6-way rack-mounted unitPower supply and cord 1TBD: Update this section for AB-Access ExtenderTBD: Update this section for AB-Access Extender – need image of Extender
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-3Figure 6-1 Outdoor AB-Access Extender Components6.4 Indoor Patch PanelFigure 6-2 shows the Base Station Access Panel used as an indoor patch panel.Figure 6-2 Access Panel used as Patch Panel6.5 Installing The EquipmentThis section explains how to install an EX transceiver onto a variety of surfaces, connect them tothe indoor junction box, and ground the system.6.5.1 OverviewFollowing are the installation steps you will perform:6. Install the mounting poles.7. Mount the outdoor transceivers.8. Mount the access panel.9. Ground the outdoor transceivers and access panel10. Connect the interconnect cables.6.5.2 Installing The Mounting PolesFirst install the mounting poles, on which you will mount the outdoor transceivers.Bear in mind the direction in which the transceivers will point.Attention! The mounting pole must be mounted in a vertical position. Failure to do somay result in improper alignment of the outdoor transceiver. If you need to tilt thetransceiver down to avoid self-interference, you should use an (optional) tilt bracket.AP/EX OUTAP/EXIN
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-4Warning! The mounting pole must be grounded. See Grounding The System in Section 6.6.3.6.5.3 Installing On An Antenna MastTBD: Update this section for AB-Access Extender4. Position the mounting pole on the antenna mast.5. Insert the U-bolts around the mast and through the holes in the mounting pole. Install awasher and nut to each side of the threaded U-bolt and hand tighten. Repeat this step for thesecond U-bolt.6. Tighten nuts equally until mounting pole is secure and cannot rotate.Figure 6-3 Mounting Pole Installed on Pole or Antenna Mast6.5.4 Installing On Brick Or Masonry7. Place the mounting plate against the wall. Use a level or plumb line to set the mounting poleperpendicular to the ground.8. Mark the hole locations.9. Set the pole aside.10. Drill ¼ inch holes at the marked locations. Drill the holes approximately ½ inch deep.11. Insert the expansion shields into the drilled holes and tap them home.12. Align the mounting pole with the drilled holes and fix with the lag bolts.Typical 2 ½ inch
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-5Figure 6-4 Mounting Pole Installation6.5.5 Installing On A Wall With Wood Siding6. Place the mounting plate against the wall.7. Using a level, be sure that the mounting pole is perpendicular to the ground. You may needto use spacers, as shown in Figure 6-6.8. Mark the hole locations for the drilled hole locations. Remove the mounting pole and setaside.9. Drill 1/8-inch holes in the places marked.10. Use #10 or #12 wood screws to secure the mounting pole to the wall and tighten.Figure 6-5 Mounting Pole on Clapboard Siding6.6 Mounting The Outdoor AB-Access ExtenderNow that you have installed the mounting pole, you are ready to install the AB-Access Extenderonto the mounting poles. Reference Figures 6-7 through 6-10.TBD: Update this section for AB-Access Extender – image of extender on mounting
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-6 Figure 6-6 Mounting Parts for an Outdoor AB-Access Extender6. Place the outdoor AB-Access Extender on the mounting pole.7. Align the pole clamp with the mounting holes.8. Insert the mounting screws and hand tighten.9. Rotate the outdoor AB-Access Extender so it is pointing in the correct direction.10. Tighten the mounting screws.TBD: Update this section for AB-Access Extender – photo of rear of Extender Figure 6-7 AB-Access Extender Rear View Figure 6-8 Tilt BracketTBD: Update this section for AB-Access Extender – insert photo of correct tilt bracket forExtender Figure 6-9 AB-Access Extender with Mounted Tilt BracketSide HexBoltsTilt Bracket
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-7TBD: Update this section for AB-Access Extender – insert photo of correct tilt bracket connectedto Extender6.6.1 Installing the Access PanelYou will probably install the Access Panel in a rack, along with the anchor switch and otherassociated equipment. However, keep in mind that the access panel should be:• Located where you can easily connect to a power supply.• Close to the anchor switch.• Accessible for service and troubleshooting.• Protected from rain and extremes of temperature (it is designed for indoor use).6.6.2 Installing The Interconnect CablesFor each interconnect cable, you will need to perform the following steps.6.6.2.1 Route The Cables4. Select where the cable will enter the building from the outside.5. Determine the length of cable required. Allow three extra feet on each end to allow for strainrelief, as well as any bends and turns.6. Route the cable.6.6.2.2 Install the Interconnect Cables (Transceiver End)3. Remove the grommet and clamping plate from the outdoor transceiver by removing the twoscrews.Figure 6-10 Grommet Location - Underside of AB-Access Extender
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-8TBD: Update this section for AB-Access Extender – insert graphic of underside of Extendershowing cable routingNOTE: The Grommet is made of a special conductive material used to complete the ground between the AB-Access Extender and Access Panel.4. Insert the cable end through the grommet clamping plate (Figure 6-11)5. Insert the cable end through the grommet. The tapered end of the grommet should beopposite the cable end.6. Strip 1 inch of insulation off the cable end. Leave 3/8 inch of shielding showing and trim thewire ends flat ½ inch from there.7. Using a piece of 1 inch squared tinned copper foil, wrap the foil around the shield/braid andsheath with the left edge aligned with the edge of the braid, as shown in the followingFigures 6-12 and 6-13.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-9Figure 6-11 Outdoor Transceiver End of the Interconnect Cable with Cable PreparationFigure 6-12 Outdoor Transceiver End of the Interconnect Cable with Shielding6. Separate the twisted pair wires and align by color code in the order listed in the followingTable 6-3.GrommetGrommetclampingplateNote directionof taperInsert wireinto channels1/2"3/8"ShieldingPin 1Tab onunderside1" square tinned copper foil - wrap the copper foil around the shield/braid and sheath with the left edge aligned with the edge of the braid.Grommet isconductiveand used tocompletethe ground
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-10Table 6-3 Cable Legend for Interconnect CablePin Color Code1 White / Orange2 Orange3 White / Green4Blue5 White / Blue6 Green7 White / Brown8Brown7. Using pin 1 as a reference, insert the individual wires into the channels of the RJ-45 connector. Each wire should penetrate the channels until flush with the connector end. The copper foil tape should extend past the casing of the RJ-45 connector by approximately ½ inch.8. When all wires are inserted into the channels in their correct order, use the crimping tool toPermanently crimp the wires to the connector. Insert the RJ-45 connector into the receptaclelocated underneath the outdoor EX. Make sure that the connector tab engages the slot in thereceptacle.13. Slide the grommet up the cable and press it into the bottom of the outdoor EX.14. Slide the grommet clamp up the cable and align the holes with the mounting holes on thebottom of the outdoor transceiver.15. Insert the two screws in the mounting holes and tighten until the grommet has a slight bulge.Be sure to tighten both screws equally so that the grommet is seated correctly.16. Secure the interconnect cable to the mounting pole with the cable clip as shown inFigure 6-14.Attention! Carefully read the instructions for the crimping tool you are using. Use the correct crimping tool for the RJ-45 connector you are using. Incorrect installation of the RJ-45 connector may result in a bad connection between the outdoor transceiver and the indoor junction box.
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-11Figure 6-13 Interconnect Cable Installation to Outdoor AB-Access Extender - BottomViewTBD: Update this section for AB-Access Extender – insert graphic for AB-Access Extenderbottom view with cable routing6.6.2.3 Installing The Interconnect Cables to Access PanelAttention! Always Disconnect Power from wall box BEFORE inserting RJ-45 connectorinto transceiver. This prevents arcing damage from occurring.3. Install an RJ-45 connector to the junction box end of the cable, following the previous steps 6through 12.4. Plug the RJ-45 into one of the upper ports in the Access Panel junction box.Figure 6-14 Access Panel showing Connections to AP/EXRJ-45 toAP/EXTransceiverGND
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-126.6.2.4 Mark the AB-Access Extender CablesAttention! Step 1 is important, and will enable the network installer to configure the system easily.2. Mark the cable with a permanent label and make a note so that the network installer knowswhich outdoor EX transceiver is connected to which port on the Access Panel junction box.6.6.3 Grounding The SystemThe AB-Access System must be properly grounded in order to protect it and the structure it isinstalled on from lightning damage. This requires:8. Grounding all the outdoor transceivers as shown in Figure 6-14.9. Grounding the Access Panel to the rack.6.6.3.1 Grounding the Outdoor AB-Access Extender8. Place the grounding rod so as to allow for the shortest possible path from the groundingcable to the outdoor AB-Access Extender.9. Drive the grounding rod into the ground at least eight inches from the ground surface.10. Attach a grounding clamp to the grounding rod. You will use this clamp to attach groundingwires for both the outdoor transceiver and indoor junction box, reference Figure 6-16.Figure 6-15 Ground Connections to AB-Access Extender Transceiver
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-13Attention! The grounding wire should be long enough to reach from the mounting pole to the grounding rod with 3 to 6 extra feet allowed for strain relief.11. Connect a ground lug to one end of the grounding wire.12. Remove one of the lower mounting screws of the mounting pole. Insert a screw through thegrounding lug terminal and re-install it to the mounting pole.13. Attach the grounding wire to the clamp on the grounding rod, reference Figure 6-17. If necessary, use wire staples to secure the grounding wire to the outside wall.Figure 6-16 Mounting Pole with Ground LugInstall a grounding wire from the junction box to the grounding rod.Ground lugwith #10 awgcopper wire
Company ProprietaryAdaptive Broadband U-NII Product Installation Manual 05/29/2001 6-1

Navigation menu