Automatic Technology PAPTX5V101 PTX-5V1 REMOTE CONTROL TRANSMITTER User Manual 1
Automatic Technology (Australia) Pty. Ltd. PTX-5V1 REMOTE CONTROL TRANSMITTER Users Manual 1
Contents
- 1. Users Manual 1
- 2. User Manual 2
- 3. Users Manual 3
Users Manual 1
![www.bnd.com.auPA700V1 - Overhead Door OperatorInstruction Manual Part number #40000Model: PA700V1October 2011PA700PA700FOR RESIDENTIAL USE ONLY(Instruction d’Installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-1.png)
![WARNING: It is vital for the safety of persons to follow all instructions. Failure to comply with the installation instructions and the safety warnings may result in serious personal injury and/or property and remote control opener damage. Please save these instructions for future reference.AVERTISSEMENT: pour la sécurité des usagers, il est essentiel de suivre toutes les instructions. Le non- respect des instructions d’installation et des avertissements de sécurité peut causer de graves blessures et/ou endommager l’appareil et la télécommande. Veuillez conserver ces instructions pour future référence.To reduce the risk of electric shock, this equipment has a grounding type plug that has a third (grounding) pin. This plug will only fit into a grounding type outlet. If the plug does not fit into the outlet, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.Pour reduire les risques de choc electrique, cet appareil est quipe d’une fiche avec mise a la terre comportant une troisieme broche (broche deterre). Cette fiche ne peut etre branche que dans une prise avec mise a la terre. S’il n’est pas possible de la brancher dans la prise, faire poser une prise appropriee par un electricien qualifie. Ne pas modifier la fiche.](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-2.png)
![CONTENTSPA700V1 Overhead Door OperatorSafety Rules 5Default Settings & Specications 6About Your Operator 7Operating Controls 8Kit Contents 10Installation Single piece C-Rail Assembly 11Mounting Operator for Track Type Door 12Mounting Door Bracket & Arms 13Safety Beam Installation 14Programming the Operator 15Via Control Panel 15Safety Obstruction Force Testing Safety Obstruction Force 16Setting Safety Obstruction Force 17Coding Transmitters For Door Operation 18For Courtesy Light Operation 18For Vacation Mode 19For Auxiliary Output 19For Pet (Pedestrian) Mode 20Deleting All Transmitter Codes 20Mounting Wall Transmitter (optional) 20Accessories Terminal Block 21Remote Aerial 21Auxiliary / Key Switch 21D Power Drive : Instruction Manual© Copyright 20113PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-3.png)
![How To Use Your Operator Transmitter 22Removing Battery from Transmitter 23Manual Door Operation 23Power Failure 23Safety Beam 24Courtesy Light 24Auxiliary Output 24Vacation Mode 24Setting The Pet Mode Position 24Maintenance 25Troubleshooting Guide 26Parameters 27Spare Parts 28Warranty 30Optional Accessories 32CONTENTSPA700V1 Overhead Door OperatorPA700V1 Instruction Manual (Instructions d’installation)4](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-4.png)
![Safety RulesPlease read these important safety rulesThese safety alert symbols indicate a personal safety or property damage instruction exists. READ THESE INSTRUCTIONS CAREFULLY. This automatic garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the following safety rules. Failure to comply with the installation instructions and the safety warnings may result in death, serious personal injury and/or property damage.CAUTION: If your garage has no pedestrian entrance door, an emergency access device should be installed. This accessory allows manual operation of the garage door from outside in case of power failure.Position the Garage Door Operator so that the power plug is accessible when inserted into the power outlet.This operator should be installed in accordance with relevant US and Canada Standards.Do not allow children to play with door controls.Keep transmitters away from children. Watch the moving door and keep people away until the door is completely opened or closed.Activate the operator only when the garage door is in full view, free of obstructions and with the operator properly adjusted.Keep the garage door balanced. Sticking or binding doors must be repaired. Garage doors, door springs, brackets and their hardware are under extreme tension and can cause serious personal injury. Do not attempt any garage door adjustment. Do not use if repair or adjustment is needed. Call for professional garage door service.Install the optional wall transmitter in a location where the garage door is visible, but out of the reach of children at a height of at least 5 feet (1.53m). Disconnect electric power to the garage door operator before removing covers.Door must have Safety Beams tted.Do not wear rings, watches or loose clothing while installing or servicing a garage door operator.This operator is not suitable for commercial, industrial or common entry applications.To avoid serious personal injury from entanglement, remove all unnecessary ropes or chains and disable any equipment such as locks which are not needed for powered operation.Installation and wiring must be in compliance with your local building and electrical codes. Connect the power cord only to properly earthed mains. If an extension lead must be used, make sure it is a 3-core lead and approved to 7 Amp capacity.To reduce the risk of electric shock, this equipment has a earthing type plug that has a third (earthing) pin. This plug will only t into a earthing type outlet. If the plug does not t into outlet, contact a qualied electrician to install the proper outlet. Do not change the plug in any way.If the power cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualied person in order to avoid a hazard.This opener is a plug in domestic appliance and is designed for indoor use only. It must be installed in a dry position that is protected from the weather. The opener is not intended for use by young children or inrm persons without supervision.WARNING! It is vital for the safety of persons to follow all instructions. Save these instructions.(Les règles de la sécurité)D Power Drive : Instruction Manual© Copyright 20115PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-5.png)
![Default Settings & SpecicationsFactory default settingsDefault Step Minimum MaximumCourtesy light time 3 minutes Not adjustable ----- ------Obstruction force margin 0.7A 0.1A 02ATechnical specicationsInput Voltage 120Vac / 60HzInput power (max) 150 WattsStandby power, less than 1.8 WattsTransformer secondary output Voltage 24VacMotor type 24Vdc geared motor with permanent magnetShuttle travel distance in the C-Rail 8.858ft (2.7m) approximately (standard)*Maximum shuttle travel distance in the C-Rail 12.3ft (3.75m) (with one extension)*Maximum door area 140sq.ft (13.5m²)Maximum door hanging weight 297.36lbs (135kg)Minimum headroom 1” (25.4mm) Receiver type UHF Multifrequency FM-ReceiverReceiver code storage capacity 8 X 4 button Transmitter CodesTransmitter frequencies 433.47MHz; 433.92MHz; 434.37MHz Coding type TrioCode™Number of code combinations Over 4.29 billion random codesCode generation Nonlinear encryption algorithmTransmitter battery CR2032 (3 Volts)Courtesy light LED’s ModuleController fuse 10A (slow blow)*The actual travel distance of the door depends on conguration of the connecting arms.NOTE: Intermittent operations may occur in areas which experience very strong winds. The strong wind puts extra pressure on the door and tracks which may in turn intermittently trigger the safety obstruction detection system.PA700V1 Instruction Manual (Instructions d’installation)6](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-6.png)
![Thank you for choosing a PA700 automatic garage door operator.The technically advanced construction of this operator ensures you enjoy the following benets:Warrantyxxx (x) years / xxxx cycles full parts and labour warranty on motor, electronics and mechanical components of the opener when installed by a garage door professional (conditions such as annual garage door servicing apply).TrioCode™ Frequency Hopping TechnologyEvery time a transmitter is used, it simultaneously sends a signal over three different frequencies, reducing the chance of interference from other radio frequency sources.Code Hopping TechnologyEvery time a transmitter is used a new security code is generated from over 4.29 billion possible code combinations. This greatly enhances the security of the system and makes “code grabbing” a thing of the past!Multi-Channel TransmitterMulti-channel transmitters allow you to operate other devices such as an adjoining garage door or automated gate from the same handy unit.Warranty Expired IndicatorThe opener will indicate that the number of cycles covered by the warranty has been reached by ashing the courtesy light 10 times after each operation. This ashing will continue for 20 cycles unless it is reset by pressing the SET button while the courtesy light is ashing.S-ALPS (Semi Automatic Limits Positioning System)The S-ALPS system does away with manual adjustment of the door’s limits position using mechanical parts, such as cams and microswitches. Safety Reversing SystemThe automatic safety reverse system signicantly reduces the risk of death or serious injury if trapped by a closing door. The safety reverse force can be adjusted for environmental conditions such as windy areas.Safety Beam ProtectionThe Safety Beam is the infrared (IR) invisible light beam system which shall protect the doorway. The door stops and reverse to the full position if anything passes through the beam.Courtesy LightThe courtesy light automatically switches on for approximately three (3) minutes when operating the door. This can also be programmed to turn on and off from a transmitter.Memory RetentionIn case of a power failure, the opener does not lose the transmitter codes or limit settings. Soft Start/Soft StopThe opener eases into and out of each cycle making for smoother and quieter operation, as well as reducing wear and tear on the door and opener.Manual ReleaseThe manual release handle allows the door to be operated by hand in the event of a power failure.Self LockingThere is no need to manually lock your garage door, as the operator ‘positively’ locks the door when closed.Periodic Maintenance IndicatorThe SERVICE LED will illuminate to indicate that periodic maintenance is required. Contact your garage door professional for service.Service Fault IndicatorFlashing LEDs on the control panel easily identify operational problems or service requirements.Dynamic Door ProlingChanging door characteristics are automatically compensated for and “learnt” with each operation of the door.External AerialAn external aerial can be connected for sites where radio reception is a problem.Vacation ModeA transmitter can be programmed to disable the garage door opener radio receiver. This is ideal if the door is to be left idle for prolonged periods.Pet (Pedestrian) ModeA transmitter can be programmed to open the door partially to allow pets access to the garage. The door opening height is adjustable via a handheld programmer.Auxiliary OutputYou can program a spare button on your transmitter to operate this output, which can control items that use a momentary close switching mechanism.About Your OperatorD Power Drive : Instruction Manual© Copyright 20117PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-7.png)
![Operating ControlsTerminal Block (J2): V+ (+35V/+24V) is used to power Accessories such as external receiver (200mA max)SB-1 (mandatory) input is used to connect to Safety Beam0V is a 0 volt connection for Safety BeamSB-2 input is used to connect to Safety Beam0V is a 0 volt connection for Safety BeamAUX/OSC This output has two chosen functions:AUX allows the operator to operate other devices such as an alarm system.OSC is used for the connection of a wired switch (momentary contact). This switch can then be used to open, stop or close the door. Install the wall switch in a location where the switch is out of reach of children and the garage door is visible.CODING LED (Red) light ashes when a code is being stored or when a transmitter button is pressed.DOOR CODE button is used for storing or erasing transmitter buttons for door operationSERVICE LED (Yellow) indicates when the opener requires service or repairs.SET button (Orange) is used during the installation phase together with the Open and MINUS (-) buttons to set the door limit positions. The Set button is also used to re-initialize the Opener.OPERATE button (Yellow) is used during installation to test the open, stop and close cycles for the opener. The opener has to be initialised by the SET button to make the OPERATE button operable.FORCE MARGIN SET button: The obstruction force margin is set automatically during installation. The margin can be adjusted manually using the Force Margin Set button (White). Holding the Force Margin Set button and pressing PLUS (+) or MINUS (-) buttons will increase or decrease the amount of force. The Force Margin Set should only be used if environmental factors (wind, etc.) affect the operation of the door.OPEN LIMIT LED (Green) the LED is very helpful during installation. It illuminates and ashes when the door is opening and remains steady on when the open limit position has been reached.PLUS (+) button (Green) is used during installation to help set the open limit position. Pressing and holding this button will move the door in the open direction, releasing stops the door.NOTE: The safety obstruction detection is inoperable when the PLUS (+) button is used to move door.CLOSE LIMIT LED (Red) the LED is very helpful during installation. It illuminates and ashes when the door is closing and remains steady on when the close limit position has been reached.MINUS (-) button (Red) is used during installation to help set the close limit position. Pressing and holding this button will move the door in the close direction. Movement stops when the button is released.NOTE: The safety obstruction detection is inoperable when the CLOSE button is used to move door.DATUM ADJUST SCREW is used during limits set up to indicate the mid point of the door’s travel.10A FUSE (Slow Blow)PROG INPUT is used to connect the handheld “PG-3” Programmer for editing control and receiver functions, accessing diagnostic tools, and activating special features and operating modes. JP1 SOLAR CONNECTOR the shunt must be tted for solar operation.COURTESY LIGHT The LEDs Module is used for the courtesy light. 01. 02. 03. 04. 05. 06. 07. 08. 09. 10. 11. 12. 13. 14. 15. 16.PA700V1 Instruction Manual (Instructions d’installation)8](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-8.png)
![Fig. 01011602 03 04 05 06 07 08 09 10 11 12131415 Fig. 02D Power Drive : Instruction Manual© Copyright 20119PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-9.png)
![Kit ContentsPA700 Kit contains (Fig. 03)1 x PA700 powerhead drive unit;1 x Transmitters set(Set includes PTX-5 (hand held remote control) and WTX-4 (wall mounted remote control) transmitters with batteries);2 x Door attachment arms;1 x Accessory and hardware pack;1 x Installation Manual.Fig. 03plusSingle Piece C-Rail with Preassembled Chain (Belt)NOTE: Chain in one piece rail has been tensioned by the factory. Do not adjust the tension of the chain.IMPORTANT NOTE: If a modication to the length of the track is required, the adjustment must be made from the powerhead end only.Fig.04PA700V1 Instruction Manual (Instructions d’installation)10](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-10.png)
![InstallationC-Rail AttachmentStep 1 - Attach C-Rail to PowerheadLocate and insert the powerhead’s shaft into the C-Rail’s sprocket as shown in Fig.05.Step 2 - Secure C-Rail to Powerhead Fix the two track brackets as shown in Fig.06. Fix with the four screws supplied in the accessory pack.Locate shaft into sprocketShaftScrews M4 X 8Track bracket (x2)Fig.06Fig. 05Where possible, install the door opener 7 feet or more above the oor.D Power Drive : Instruction Manual© Copyright 201111PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-11.png)
![TrackLevelDoorDrilled holesStructural memberFig.10Fig.9Fig.8Fig.7Mounting Operator for Track Type DoorStep 3 - Determine Bracket PositionOpen the door and nd the highest point of travel of a. the top door panel.Using a level, transfer this height to the wall above the b. door (Fig.7) and mark a line 2.36” (60mm) above it.Determine the centre point on the wall above and c. on top of the door. Then draw two lines extending 21.5mm from each side of the centre point. (Fig.8)Step 4 - Mounting the Wall BracketCentre the bracket over the intersection of these two a. lines. Mark centres for at least two holes (Fig.8).Ensure a solid mounting point is behind these • holes.Drill holes into the wall with an appropriate sized bit.b. Secure bracket to the wall using: c. IF CONCRETE OR BRICK - 8mm or 5/6 loxins or dynabolts. IF TIMBER - wood screw #20 or equivalent (minimum 50mm long).Step 5 - Attach the C-Rail to the Wall BracketAttach the C-Rail assembly to the wall bracket with the a. 90mm long clevis pin and secure with the supplied snap pin (Fig.9).Leave the powerhead in its packing box for protection b. during installation.Step 6 - Securing the Powerhead to the CeilingRaise the powerhead from the packing box and a. support it in the horizontal position with a step ladder.Open the garage door. Rest the opener on the open b. door and use a scrap piece of wood to bring it to horizontal level. Line up the track perpendicular to the wall.c. Secure the perforated angle (not supplied) to the d. ceiling above where the powerhead’s mounting holes will be once fully installed. A representative mounting is shown (Fig.10).Connect the powerhead to the ceiling mounted e. perforated angle with M8x20mm screws and nuts. Strips should not extend more than 0.71” (18mm )below the centre of the powerhead mounting holes (Fig.10).WARNING: The opener must be securely fastened to structural supports, otherwise opener failure may ensue causing serious personal injury and/or property damage.WARNING: Make sure concrete, brick wall or timber lintels are solid and sound so as to form a secure mounting platform.4321.521.5PA700V1 Instruction Manual (Instructions d’installation)12](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-12.png)
![Fig.11Fig.12Fig.13Mounting Door Bracket and ArmsStep 7 - Alternative Mounting OptionThe operator can be fastened to the roof by driving a bolt through the C-Rail into a structural timber support. The bolt head’s height must not exceed 6mm (Fig.11).Step 8 - Mounting Door BracketThe door bracket comes in two parts. The bottom plate with two mounting holes is used on its own for one piece doors. For sectional doors, the top plate is placed over the bottom plate and is xed with four (4) screws (Fig.12).Mount the door bracket, or bracket assembly, on the a. door’s centre line one-third down the top panel (Fig. 12) using M6 or equivalent screws (not supplied),STEEL DOORS ONLY: Bracket can be welded in b. place.NOTE: If in doubt about the door’s strength, reinforcement may be added to the door’s frame where necessary. Door damage may occur if the bracket is installed on a panel with insufcient strength. The opener’s warranty does not cover damage caused to the door and/or door panels.Step 9 - Attaching the Arms Assemble the bent and straight arms with bolts a. and nuts supplied in the accessory pack (Fig.13). Always use both bent and straight arms.Connect the assembled arm to the bracket and the b. disengaged trolley with clevis and snap pins. The angle “A” must be more than 10° (Fig.13).WARNING: Connecting the bent arm other way around may damage the door.IMPORTANT NOTE: If the manual release handle is higher more than 6 feet (1.83m) from oor level when the operator is installed, extend the handle to a height 6 feet (1.83m) or less.CeilingSteel railShuttle assemblyDrill hole at centre of track (recommended bolt size M6 or M8)The height of bolt head must not exceed 0.236” (6mm)100AD Power Drive : Instruction Manual© Copyright 201113PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-13.png)
![WARNING: When the Safety Beam is tted, the doorway must be clear of all obstructions and persons at all times. The location of the beams and manner in which it is installed might not give safety protection at all times. Check to make sure that the height of the beam and type used give maximum protection possible.IMPORTANT NOTE: The Safety Beam must be installed and connected before the travel limits are set Step 10 - Safety BeamA Safety Beam extends across the door opening. This Safety Beam is designed to detect an obstruction while the door is closing and to send a signal to the door operator to reverse or stop the door movement.Step 10.1 - Fitting the Safety BeamAttach the mounting bracket (4) to the adjustment a. bracket (3) with the pan head screw (5) (supplied). (Fig. 14).Attach the bracket (2) to the Safety Beam transmitter b. (PE3-V1-TX) (1) with four taptite screws (6) (M3x5) and attach the other side to the adjustment bracket (3) with the pan head screw (5) (supplied).Repeat steps “a” and “b” to assemble the Safety Beam c. (PE3-V1-RX) receiver.Locate the Safety Beam in a strategic location in the d. door opening. We recommends that the sensor is placed no higher than 6” and no lower than 5”above the oor level. Connect as per the wiring diagram (Fig.16).Step 10.2 - AlignmentPower up the PA700 with the Beam connected. The a. green LED of the transmitter should be ON to indicate that power is present.If the receiver is connected properly and the red LED is b. ashing while the green LED of the transmitter is ON, the transmitter and receiver are not aligned.Make horizontal and/or vertical adjustment c. (Fig.15) on the transmitter and/or receiver until the red LED of the receiver turns steady on, indicating alignment.123455Fig.14Fig.15Fig.16WARNING: Install the Safety Beam as per diagram in Fig. 16. Tampering with the Safety Beam could result in serious personal injury and/or property damage and will void the warranty.Safety Beam Installation6PA700V1 Instruction Manual (Instructions d’installation)14](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-14.png)
![PA800V1120Vac/60Hz165WProgramming The OpenerStep 11.1 - Setting Limits PositionsRemove the controls cover to access the controls panel as shown in (Fig.17). Replace it when setup is completed.Step 11.2 - Connect Power to the PowerheadPlug the power cord into a mains point and switch power on. The red CLOSE LIMIT LED will be ashing.Step 11.3 - Set the Datum PositionPress and hold the MINUS (-) or PLUS (+) buttons to a. move the door to the halfway position. Ensure that the door, shuttle and chain index are engaged.Using a small screwdriver, turn the DATUM ADJUST b. screw until the STATUS LED comes on (Fig.18).Step 11.4 - Set the Limits PositionsPress and hold the MINUS (-) button until the door a. reaches the desired close limit position. Single presses will inch the door closed (Fig.19).Press the SET button to store the close position into b. memory (Fig.19).Press and hold the PLUS (+) button until the door c. reaches the desired open limit position. Single presses will inch the door open (Fig.19).Press the SET button to store the open position into d. memory (Fig.19).Fig.19Fig.18Fig.17IMPORTANT NOTE: The OPERATE button will not function until the open and close limit positions are set.NOTE: The Safety Beam must be installed before setting the travel limits.NOTE: The door and shuttle must be engaged into the chain index. The door should be open approximately half way.WARNING: The safety obstruction detection system is inoperable while MINUS (-) and PLUS (+) drive buttons are being used and travel limits are not set.WARNING: The door will automatically close, open and close again once Step 11.4(d) is performed. Ensure that no persons or objects are in the door’s path.The door will now automatically close and open to e. calculate the safety obstruction settings. After this, the opener can be operated with the OPERATE button.NOTE: If the STATUS LED is already illuminated when the door is halfway up, turn the DATUM ADJUST screw until the light goes off, then turn back one notch to illuminate again.Via Control PanelD Power Drive : Instruction Manual© Copyright 201115PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-15.png)
![Testing Safety Obstruction ForceStep 12.1 Test the Close CyclePress the OPERATE button to open the door a. (Fig.20).Place an object approximately 1-1/2”(38mm) high (or b. a 2”x 4” board laid at) on the oor under center of garage door opening (Fig.21).Press the OPERATE button to close the door.c. When door contacts the object, the door must stop d. (within 2 seconds) and reverse to open position.If the door does not properly reverse.Check the “close” limit position. It should not have • reached its “close” limit before hitting board.If the door STOPS but does not reverse, decrease • FORCE (refer to Step 12.4).Step 12.2 Testing the Open CyclePress the OPERATE button to close the door a. (Fig.20).Press again to open the door.b. When the door reaches approximately halfway, rmly c. grab the door’s bottom rail - the door should stop.If the door does not stop when opening, the force may be excessive and need adjustment, refer to 12.4.Fig.21Fig.20IMPORTANT WARNING: If the door is closing and is unable to re-open when obstructed, discontinue use. Do not use a door with faulty obstruction sensing. Repair fault and re-test before using.CAUTION: Take care when testing the Safety Obstruction Force. Failure to follow this warning can result in serious personal injury and/or property damage.2”x 4” boardPA700V1 Instruction Manual (Instructions d’installation)16](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-16.png)
![Setting Safety Obstruction ForceAdjusting Safety Obstruction ForceThe safety obstruction force is calculated automatically and normally does not require adjustment. The only time the force may need to be adjusted is due to environmental conditions, such as areas that are windy, dusty or have extreme temperature changes that affect the operability and movement of the door.Step 12.3 - To Increase Force Pressure (Fig.22)Press and hold the FORCE MARGIN SET button.a. While holding down the FORCE MARGIN SET button, b. press the PLUS (+) button. Each press will increase the force margin one step.The OPEN LIMIT LED will ash each time the PLUS c. (+) button is pressed to indicate an increase in force.If the OPEN LIMIT LED ashes continuously when the d. PLUS (+) button is being pressed, this indicates that the maximum force setting has been reached.Test the force again as per e. Steps 12.1 and 12.2.Step 12.4 - To Decrease Force Pressure (Fig.23)Press and hold the FORCE MARGIN SET button.a. While holding down the FORCE MARGIN SET button, b. press the MINUS (-) button. Each press will decrease the force margin one step.The CLOSE LIMIT LED will ash each time the MINUS c. (-) button is pressed to indicate a decrease in force.If the CLOSE LIMIT LED ashes continuously when d. the MINUS (-) button is being pressed, this indicates that the minimum force setting has been reached.Test the force again as per e. Steps 12.1 and 12.2.Step 12.5 - To Recall Factory Set Force While holding down the FORCE MARGIN SET button a. press the SET button for two seconds (Fig 24).Release both buttons. The default setting should now b. be recalled.WARNING: Safety Beam must be installed if the closing force as measured at the bottom edge of the door exceed 200N (20kg).Fig.22Fig.24Fig.23D Power Drive : Instruction Manual© Copyright 201117PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-17.png)
![Coding TransmittersFig.25Fig.26Step 13.1 - Coding a Transmitter Button for Door Operation (Fig.25)The operator can only operate from transmitters that have been programmed into its receiver. The receiver needs to learn the codes of any transmitter that will be used with the operator. Up to eight (8) codes can be stored in the receiver’s memory.Press and release the a. DOOR CODE button. The DOOR CODE LED will illuminate to indicate the opener is in Code Learn mode. If a valid code is not stored within 15 seconds the operator will exit Code Learn.Press one of the four buttons on the transmitter. The b. DOOR CODE LED will begin to ash.Press the same transmitter button again. The DOOR c. CODE LED will illuminate for one second and then go out.The transmitter is now coded to operate the door. Press d. that button to test again.Step 13.2 - Setting the Transmitter to Operate the Courtesy Light (Fig.26)Although the courtesy light comes on with each operation of the opener, it may also be controlled by a transmitter without operating the door.Press the a. DOOR CODE button twice. The DOOR CODE LED will illuminate and the courtesy light will turn on to indicate that the light code learning is active.Choose a transmitter button not already coded into the b. receiver. Press this button and the DOOR CODE LED will begin to ash.Press the same transmitter button again. The DOOR c. CODE LED will illuminate for one second and then go out.The transmitter is now coded to operate the light. Press d. that button to test again.Transmitters Compliance StatementTransmitters comply with all United States and Canadian legal requirements as of the date of manufacture. To comply with FCC Part 15 and or RSS 210 of Industry Canada (IC) rules, adjustment or modications of this receiver and / or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standard FOR HOME OR OFFICE USE. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.Select one of the four buttonsSelect one of the four buttonsPA700V1 Instruction Manual (Instructions d’installation)18](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-18.png)
![Fig.28Fig.27Coding TransmittersStep 13.3 - Setting the Transmitter to Operate Vacation Mode (Fig.27)The operator can be programmed into a “Vacation Mode” where the opener will not respond to any transmitter except one preprogrammed unit.Press a. DOOR CODE button three times. The DOOR CODE LED will illuminate and the courtesy light will ash slowly (once every two seconds) to indicate Vacation learning mode is active.Choose a transmitter button not already coded into the b. receiver. Press this button and the DOOR CODE LED will begin to ash.Press the same transmitter button again. The DOOR c. CODE LED will illuminate for one second and then go out, and the courtesy light will also switch off. This indicates the code has been stored.To activate Vacation Mode, close the garage door and d. press the coded button transmitter for 5 seconds. The DOOR CODE LED will illuminate to indicate that the opener is in Vacation Mode.To exit Vacation Mode press the transmitter button e. momentarily until the DOOR CODE LED turns off.Step 13.4 - Setting the Transmitter to Operate the Auxiliary Output (Fig.28)It is possible to operate other devices (e.g. alarm systems) using one of the spare buttons of a multi-channel transmitter coded into the Auxiliary Output feature.Press the a. DOOR CODE button four times. The DOOR CODE LED will illuminate and the courtesy light will ash quickly (twice per second) to indicate that learning mode for the Auxiliary Output is active.Choose a transmitter button not already coded into the b. receiver. Press this button and the DOOR CODE LED will begin to ash.Press the same transmitter button again. The DOOR c. CODE LED will illuminate for one second and then go out, and the courtesy light will also switch off. This indicates the code has been stored.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna•Increase the separation between the equipment and receiver•Connect the equipment into an outlet on a circuit different from that to which the receiver is •connectedConsult your local dealer or an experienced radio/TV technician for help.•Select one of the four buttonsD Power Drive : Instruction Manual© Copyright 201119PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-19.png)
![Fig.29Fig.30Fig.31Coding TransmittersStep 13.5 - Setting the Transmitter to Operate Pet (Pedestrian) Mode (Fig.29)The operator can be programmed into a “Pet Mode” where the door opens partially to allow pets to enter/exit the garage:Press the a. DOOR CODE button ve times, the DOOR CODE LED will illuminate and the courtesy light will ash quickly (twice per second) to indicate learning mode for Pet Mode is active.Choose a transmitter button not already coded into the b. receiver. Press this button and the DOOR CODE LED will begin to ash. Press the same transmitter button again. The DOOR c. CODE LED will illuminate for one second and then go out, and the courtesy light will also switch off. This indicates the code has been stored. This indicates the code has been stored.The opening height of the door for pet position can only d. be changed with a universal programmer.Step 13.6 - To Erase Programmed Codes (Fig.30)If the DOOR CODE button is pressed and held for 6 seconds the DOOR CODE LED will blink rapidly for one second to indicate that all programmed codes have been erased.Step 13.7 - Installation of the Wall Mounted Transmitter (Fig.31)Mount the transmitter in a convenient location, yet out a. of reach of children and at least 5 feet (1.53m) off the ground, andAway from all moving parts of the door.b. Make sure the door is visible from this location.c. To set the transmitter codes, refer to d. Step 13.1.NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such modications could void the user’s authority to operate the equipment.PA700V1 Instruction Manual (Instructions d’installation)20](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-20.png)
![Fig.32AccessoriesTerminal BlockA variety of wired accessory items can be connected to the terminal block J2 such as Safety Beam, Electric Key Switch and more (Fig.32).The terminal block J2 also features auxiliary output for controlling other devices from your transmitter. These can include: an alarm system, additional mega code receiver or an automatic gate.Terminal J2 connections from top to down are as follows:V+1. (+35V/+24V);SB-12. (Safety Beam input, mandatory);0V3. (0V for Safety Beam);SB-24. (Safety Beam input);0V5. (Common ground for accessories and Safety Beam);AUX6. (Auxiliary output trigger)/ OSC (Open/Stop/Close trigger).Remote AerialSome sites cause poor radio reception. Particularly problematic areas are those where there is a large amount of metal, like an all steel garage, or an underground car park with large masses of steel reinforced concrete. These issues, and others, can create radio reception issues.Poor radio reception will be noticed by a reduction in the operating range of the transmitters.You can evaluate whether tting an external aerial will benet as follows:test the maximum operating range of the transmitter • with the garage door closed; thentest the maximum operating range of the transmitter • with the garage door open.If the range improves when the door is open you can install a remote aerial kit to improve reception.Mount the aerial to a suitable location on the outside of the garage. Similar to a television aerial, the better the mounting position the better the reception will be. Where possible, mount the aerial as high as possible, away from masses of metal and in a line of sight position to where you normally use your transmitter.Auxiliary / Key Switch ConnectionAuxiliary / Key Switch terminal can either be used to connect a key switch or to use as an auxiliary output. An Key Switch provides an alternative to using a transmitter. Each key turn cycles through an open/stop/close function. The electric key switch is also an external release mechanism, it is ideal for garages with one entrance only. To connect the key switch to the opener’s terminal block refer to Fig.31.The Auxiliary Output can be used to control alarm or another garage door operator with the existing garage door remote control. A valid transmission from the pre-coded transmitter will cause the AUX output to pulse for 1 sec. The maximum DC voltage must not exceed 35V. Maximum current must not exceed 80mA. Connect the auxiliary output as per Fig.32.V+SB-10VSB-20VAUX/OSCFig.31V+SB-10VSB-20VAUX/OSCJ2Fig.32External deviceAlarm, Door operator etc.V+SB-1SB-20V0VAUXOSCD Power Drive : Instruction Manual© Copyright 201121PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-21.png)
![Fig.33How To Use Your OperatorFor maximum efciency of your operator, your garage door must be in good operating condition.An annual service of your garage door by a garage door professional is recommended.CAUTION - Activate the operator only when the door is in full view, free of obstructions and with the operator properly adjusted. No one should enter or leave the garage while the door is in motion. Do not allow children to play with or near the door.WARNING! This operator is a mains voltage plug-in domestic appliance and there are no user serviceable parts inside this operator.TransmitterTo operate the operator, press the programmed • transmitter button until your door begins to move (usually 2 seconds). Make sure you can see the door when you use the transmitter.If you are in a vehicle you should aim the transmitter • through your windscreen (Fig.33).Check that the door is fully closed before you drive • away.If you press the transmitter whilst the door is moving • the door will stop. The next press of the transmitter will move the door in the opposite direction.The transmitter may also be programmed to operate the following features (see Pages 18 to 20 for full details):to turn the courtesy light on and off without operating • the door, to activate the Auxiliary Output,• to put the door into “Pet Mode” where it opens partially • to allow pet access to the garage, and/orto put the garage door opener into “Vacation Mode” • where it will not respond to any transmitters.NOTE: Additional transmitters may be purchased at any time.PA700V1 Instruction Manual (Instructions d’installation)22](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-22.png)
![Fig.34REPLACE BATTERY WITH CR2032 ONLYHow To Use Your OperatorRemoving the Battery From the Transmitter(Battery Type: 3V Lithium Battery CR2032). Use a non-metallic object (e.g. pen) to remove the battery. (Fig.34) In-built Locking FacilityDO NOT lock your door when your operator is engaged as it has in-built locking facility. With the operator engaged your door will be locked whether the power is on or off.Manual Door OperationCAUTION: when operating the manual release while the door is open. The door may fall rapidly due to weak or broken springs, or due to being improperly balanced.CAUTION! Do not disengage the operator to manual operation with children/persons or any objects including motor vehicles within the doorway.To disengage the operator from the door (preferably with the door in the closed position), pull down on the string handle on an angle towards the door. This will allow you to manually open or close the door. To re-engage the operator pull the string handle away from the door.WARNING! When the operator is manually disengaged, the door is no longer locked. To lock the door manually, re-engage the operator after the door is closed.Power FailureWhen there is a power failure, the operator will be unable to automatically open or close your garage door. To use your door whilst there is no power you will need to disengage the operator and use the door manually – see Manual Operation above.D Power Drive : Instruction Manual© Copyright 201123PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-23.png)
![How To Use Your OperatorSafety BeamA Safety Beam Kit must be tted to this operator. When this Kit is tted, the operation of this device is • such that if an object (i.e. car, child, etc.) blocks the Safety Beam, then the garage door operator will not close the door automatically.When the Safety Beam is tted but not operating • correctly, then the door once opened automatically, will not close automatically. The door may be closed by reverting to manual operation – see Manual Operation.Courtesy LightThe Courtesy Light will illuminate for approximately three (3) minutes each time the door is operated automatically.Spare buttons of a multi-channel transmitters can be programmed to turn the light on and off by remote control.See Step 13.2 for more information. Auxiliary (AUX) / Operate (OSC) OutputThe Auxiliary Output allows the opener to operate other devices such as another opener or an alarm system.To use this function, a spare button of a multi-channel transmitter must be programmed to operate the Auxiliary Output feature.See Step 13.4 for more information.The Operate (OSC) function allows the operator to open/stop/close the door. Connect a normally open switch to this input for operation. Vacation ModeThe radio receiver of the garage door operator can be turned off to all but one transmitter via Vacation Mode. Whilst in vacation mode the operator will not respond to any transmitter.To activate the Vacation Mode facility, see Step 13.3.NOTE: program only one button to control “Vacation Mode”. This will reduce the possibility of accidental activation of this feature.Pet (Pedestrian) ModeA transmitter can be programmed to open the door partially to allow pet access to the garage. To activate Pet Mode press the transmitter button that has been programmed for Pet Mode - The door will open partially.See Step 13.5 for more information. PA700V1 Instruction Manual (Instructions d’installation)24](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-24.png)
![MaintenanceThe SERVICE LED will indicate the requirement for a service and/or adjustment. To reset the SERVICE LED when the door is serviced, reprogram the Door Travel Limits and the Door Travel Force – on completion of this programming the SERVICE LED will go out.Whilst your operator does not require any periodic maintenance, the door that it is tted to does. Your garage door is a large, heavy, moving object and should be tested regularly to ensure it is in good condition. A poorly maintained door could cause fatal or serious injuries or serious damage to property.To ensure a long and trouble free life for your operator the following is recommended:MonthlyDisengage the operator and manually operate the • door: The door must be smooth to operate by hand. An operating force on the bottom rail should not exceed 150N (15kg (33lbs)) force.Each month check that the operator reverses when • the door contacts a 1-1/2” high object placed on the oor. Refer to the Safety System (Pages 16-17).NOTE: If the door does not operate smoothly or the safety reverse test failed, CONTACT A TRAINED DOOR SYSTEM TECHNICIAN.YearlyWe suggest that you contact your nearest garage door professional to perform an annual door service.Warranty Expired IndicatorWhen the operator reaches the number of cycles covered by warranty the courtesy light will ash 10 times after each operation to indicate that the warranty has expired. This ashing will continue for twenty (20) operations unless the user acknowledges the warranty expiry indicator and stops the light from ashing. To stop the courtesy light ashing press the SET button while the light is ashing after an operation.CAUTION: Frequently examine door, particularly cables, springs and mountings for signs of wear, damage or imbalance. Do not use if repair or adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury.Adjustments should only be carried out by experienced persons, as this function can be dangerous if not performed under strict safety procedures.WARNING! Failure to maintain your garage door may void the warranty on your garage door operator.Date Service by Signature Invoice No. AmountService RecordRecord any maintenance in the following table to assist in any warranty service.D Power Drive : Instruction Manual© Copyright 201125PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-25.png)
![If You Need a Service CallIf the opener needs service, call the dealer who installed the garage door operator (for product assistance contact .........).BEFORE CALLING you should have the following information to assist in providing the appropriate service:Has anything happened since the operator last 1. operated OK, e.g. a storm, a jolt to the door etc.?How easy is it to manually open and close the door?2. What model is the operator?3. Who installed the operator?4. When was it installed? 5. Fault IndicatorWhen a fault is detected the SERVICE LED will start to ash and a number of beeps will sound to indicate that there is a fault. The fault will be active each time an attempt is made to operate the door.Pressing the SET button will reset the opener. If the fault continues to be tripped contact a garage door professional for assistance.Troubleshooting GuideSymptom Possible cause RemedyThe opener does not work from the transmitterGarage door in poor condition e.g. springs may be brokenThe opener does not have powerThe battery in the transmitter is at The opener has been put into “Vacation Mode” The transmitter code has not been set properlyCheck the door’s operation - see monthly maintenance (Page 25)Plug a device e.g. a lamp, into the power point and check that it is OKReplace the battery (Page 23) Turn off “Vacation Mode” (Page 19) See transmitter & code setting procedure (Page 18)The motor runs but the door does not moveThe opener is disengaged Re-engage the opener (Page 23)The transmitter range varies or is restrictedVariations are normal depending on conditions e.g. temperature or external interferenceThe battery is at or faultyPosition of the transmitter in the motor vehicle Position of the aerial will not pick up the radio signalSee instructions for correct use of transmitter (Page 22)Replace the battery (Page 23)Change the position (Page 22) Install an external aerial kit – see Accessories (Page 21)The light does not work Light module is not inserted/connected properlyCheck for correct connection otherwise contact a garage door professional for supportThe door reverses for no apparent reasonThis may occur occasionally from weather changesThe opener automatically adjusts to compensate for changes, to adjust the force see (Pages 16, 17)PA700V1 Instruction Manual (Instructions d’installation)26](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-26.png)
![ParametersDoor status indicatorsDoor opener state OPEN LED (green) CLOSE LED (red) BeeperOpen OnClose OnOpening FlashingClosing FlashingDoor travel stopped Flashing FlashingDoor obstructed when opening FlashingDoor obstructed when closing Flashing Beeps while door is movingOpener overloaded Alternating ashes Alternating ashesMains power interrupted Rapid ashesButton FunctionOPERATE Opens/stops/closes the doorDOOR CODE Codes a transmitter button for operate functionFORCE MARGIN SET & PLUS (+) Increases the obstruction force margin settingFORCE MARGIN SET & MINUS (-) Decreases the obstruction force margin settingFORCE MARGIN SET (then) SET Reloads the factory set default obstruction force margin setting(-) (for 6 seconds) Clears the door limits set positions. Limits then need to be resetSET press and hold until all LEDs are offDeletes control parameters excluding transmitter storage memoryDOOR CODE press and hold until DOOR CODE LED starts ashingDeletes all transmitter storage memorySET & DOOR CODE press and hold until all LEDs are offDeletes all control parameters and transmitter storage memoryD Power Drive : Instruction Manual© Copyright 201127PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-27.png)
![Spare parts listPA700V1 Instruction Manual (Instructions d’installation)28](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-28.png)
![D Power Drive : Instruction Manual© Copyright 201129PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-29.png)
![Warranty1. Denitions ‘Purchaser’ means the purchaser of the Operator. ‘Operator’ means the ‘PA700 Automatic Garage Door Operator’ ‘Authorised Distributor’ means an authorised distributor of the Operator. ‘Major Components’ means all components of the Operator that make up the powerhead that is attached to a garage door.‘Ancillary Components’ means all components of the Operator which are not Major Components. ‘Manufacturer’s Written Instruction Manual’ means the instruction manual provided with the Operator.2. PA700V1 Instruction Manual (Instructions d’installation)30](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-30.png)
![WarrantyPurchased From: Installed By:Installed Date:The Purchaser shall complete this certicate and keep it together with a copy of the receipt of purchase in a safe place – production of such information will assist the handling of a claim made under this warranty.D Power Drive : Instruction Manual© Copyright 201131PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-31.png)
![Optional AccessoriesThere is a range of additional accessories for your added convenience and security.• Keyring Transmitter - Ideal for personal use when entry into the house may be via the garage.• Transmitter Wall Button - Allows you to operate the operator within 32.8ft (10 metres) of the door. Ideal for mounting inside the house.• Combo Access Kit - Keyswitch function will open the door without a transmitter. Can be used to manually disengage the operator, and recommended when the garage door is the only access to the garage.• Remote Aerial Kit - For sites where radio range may be reduced.Contact your garage door professional for installation of these accessory items.When installing any accessories, always follow the instructions included with the product.Only our accessories purchased from a garage door professional offer the highest quality and assure you of trouble free opener operation.PA700V1 Instruction Manual (Instructions d’installation)32](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-32.png)
![D Power Drive : Instruction Manual© Copyright 201133PA700V1 Instruction Manual (Instructions d’installation)](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-33.png)
![www.©Copyright October 2011. All Rights Reserved.](https://usermanual.wiki/Automatic-Technology/PAPTX5V101.Users-Manual-1/User-Guide-1728817-Page-34.png)