Audio Technica R220 Communications Receiver User Manual users manual

Audio-Technica Corporation Communications Receiver users manual

users manual

Audio-Technica Model ESW-R220/210 and T211/T214UHF Wireless Microphone SystemUser Information DRAFTIntroductionThank you for purchasing the ESW series wireless microphone system. It is our hope thatthe system will bring you years of trouble free pleasure and performance. Please followthe information contained in this manual closely as it will assist you in using yourequipment effectively.Part 1. Regulatory RequeirementsFCC PART 15 COMPLIANCE STATEMENTCANADA RSS-210 COMPLIANCE STATEMENT“This device complies with Part 15 of the FCC rules. Operation is subject to the conditionthat this device does not cause harmful interference.”“This device complies with INDUSTRY CANADA R.S.S.210, en conformite avecIC:RSS-210/CNR210. Operation is subject to the following conditions: (1) This devicemay not cause harmful interference and (2) this device must accept any interferencereceived, including interference which may cause undesired operation.”Please not that your ESW Series system operates in a frequency band and in a way whichmakes is use subject to certain FCC and other regulatory restrictions and licensingrequirements. For further information, please contact your local office of the FCC asapplicable.Part 2. Using the ESW-T211 Beltpack TransmitterThe beltpack transmitter operates on 2 “AA” size batteries. Please make sure that yourbatteries are fresh. We recommend that you use Alkaline batteries and that you avoidusing NiCad if possible.Insert batteries into the battery compartment and slide the battery compartment back intoplace.
Open the rubber cover over the channels selector switch and set the group and channel tothe corresponding channels as set on the receiver. Replaces the cover over the rotaryswitches.Connect your microphone or guitar cables to the connector on the top sides of thetransmitter. If you want the low cut to be on, switch this in.Turn the transmitter switch to the on position. Confirm that the receiver is receiving RFand that the audio is passing through the receiver.You are now set to use the system.Part 3. Using the ESW-T214 Handheld TransmitterThe handheld transmitter operates on 2 “AA” size batteries. Please make sure that yourbatteries are fresh. We recommend that you use Alkaline batteries and that you avoidusing NiCad if possible.Insert the batteries into the battery compartment and slide the battery compartment coverback into place.To change the channel of operation, unscrew the battery compartment cover and pull thecover back. Locate the channel selector rotary switches. Set the group and channel to thecorresponding channel as set on the receiver. Replace the cover over the rotary switches.Turn the transmitter switch to the on position. Confirm that the receiver is receiving RF.Speak directly into the microphone and confirm that audio is passing through the receiver.You are now set to use the system.Part 4. Using the ESW-R210/R220 ReceiverThe ESW-R210/R220 receivers operate on a 110 VAC plug. Plug the unit into an ACoutlet. Push the on/off switch. Confirm that the LED comes on. Check the group andchannel setting to confirm that they correspond to the settings of the transmitter.Connect the balanced or unbalanced audio output to your mixer PA system. Adjust thevolume setting to the desired level. Speak into the microphone and listen to the audio outat the speaker. If satisfied with the audio quality, you can use the system.
ESW Operation specificationESW-R210/R220Operating Band: 728.125-740.500MHzType of Reception: F3EFrequency Response: 100Hz to 15kHzNo. of Channels: 100Audio Output Power: Line level, UnbalancedSignal to Noise Ratio: >80 dBaAntenna Connector: BNC-R typeSelectivity: > 50dBSpurious Rejection: > 50dBReceiver Sensitivity: </= uV for 60 dB S/N, (IEC weighted)ESW-T211 Beltpack TransmitterOperating Band: 728.125-740.500MHzType of Modulation: FM, F3EFrequency Response: 100Hz to 15kHzNo. of Channels: 100Transmitter Power: 10 mW nominalSpurious Emissions: Under federal regulationsBattery: 2 x 1.5V AA size
ESW-T214 Handheld TransmitterOperating Band: 728.125-740.500MHzType of Modulation: FM, F3EFrequency Response: 100Hz to 15kHzNo. of Channels: 100Transmitter Power: 10mW nominalSpurious Emissions: Under federal regulationsBattery: 2 x 1.5V AA

Navigation menu