Audio Technica R1820AD WIRELESS MICROPHONE RECEIVER User Manual Layout 1

Audio-Technica Corporation WIRELESS MICROPHONE RECEIVER Layout 1

Owners Manual

wirelesswirelesswirelesswirelesswireless1800 SeriesCamera-mount UHF Wireless Microphone Systems (dual-channel)AT W -1821UniPak®Body-pack Transmitter SystemAT W -1822Plug- on Transmitter SystemAT W -1823Plug-on and Body-pack Transmitter SystemSet-up and Operation
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. This device complies with INDUSTRY CANADA R.S.S. 210, en conformité avec IC: RSS-210/CNR210. Operation is subject to the following conditions: 1) This device may not cause harmful interference and 2) this device must accept any interferencereceived, including interference which may cause undesired operation. Changes or modifications not expressly approved by Audio-Technica couldvoid your authority to operate this equipment.Notice to individuals with implanted cardiac pacemakers or AICD devices:Any source of RF (radio frequency) energy may interfere with normal functioning of the implanted device. All wireless microphones have low-power transmitters (less than 0.05 watts output) which are unlikely to cause difficulty, especially if they are at least a few inches away.However, since a “body-pack” mic transmitter typically is placed against the body, we suggest attaching it at the belt, rather than in a shirt pocketwhere it may be immediately adjacent to the medical device. Note also that any medical-device disruption will cease when the RF transmittingsource is turned off. Please contact your physician or medical-device provider if you have any questions, or experience any problems with theuse of this or any other RF equipment.CAUTION! The circuits inside the receiver and transmitter have been precisely adjusted for optimum performance and compliance with federal regulations. Do not attempt to open the receiver or transmitter. To do so will void the warranty, and may cause improper operation. Warning: To prevent fire or shock hazard, do not expose this appliance to rain or moisture.Attention: Pour prévenir feu ou choc électrique, ne pas exposé l'appareil à la pluie ou à l'humidité.About RF InterferencePlease note that wireless frequencies are shared with other radio services. According to Federal Communications Commission regulations, “Wireless microphone operations are unprotected from interference from other licensed operations in the band. If any interference is receivedby any Government or non-Government operation, the wireless microphone must cease operation...”If you need help with operation or frequency selection, please contact your local dealer or Audio-Technica. Extensive wireless informationalso is available at www.audio-technica.com.ContentsComponents and System Configurations 3System Features 4Quick Overview of System Operation 5Receiver Controls 6Operating the Receiver 8Transmitter Controls 11Operating the Transmitter 12Tips for Best Results 14Available Accessories 14Specifications 15Warranty 162
1800 Series Components (dual-channel)Receiver and Included Components/AccessoriesAT W -1823Camera-mount UHF Wireless Microphone System (dual-channel) with Body-pack and Plug-on Transmitters ATW-R1820Dual-channel receiverTwo detachable antennasTwo 18" output cables, TA3F to XLRMPouch with belt clip (holds receiver)TransmittersATW-T1801UniPak®transmitter with included omnidirectional lavalier microphoneATW-T1802Plug-on transmitterAT W -1821Camera-mount UHF Wireless Microphone System (dual-channel) with Body-pack Transmitters AT W -1822Camera-mount UHF Wireless Microphone System (dual-channel) with Plug-on TransmittersSystem Configurations3Note: All model numbers have an additional letter at the end to indicate frequency band.
System Features (dual-channel)• Two completely independent receiver channels in a single unit, for simultaneous operation of two microphones • True Diversity operation for resistance to multi-path interference and dropouts • UHF reception with 996 frequencies selectable in 25 kHz steps • Automatic frequency scanning for easy selection of open channels • Tone Lock™ squelch system eliminates interference when transmitter is off • Two independent balanced outputs • Headphone monitor output with independent level control• Battery fuel-level indicators on transmitters and receiver• Soft-touch controls for easy frequency selection• LCD frequency and battery status display with backlight on receiver and transmitters• Antenna and AF Peak LED indicators • Dual-channel receiver can operate in single-receiver mode to extend battery life when only one audio channel is required• Compact dual receiver is easy to mount on a camera • Transmitters operate in low or high transmission modes to conserve battery life/maximize power• Easy, user-friendly operation• Clear, natural sound quality• Powered by AA batteries or by external 12V DC power (not included)• System components of the 1800 Series and 3000 Series UHF wireless systems can be used interchangeably** NOTE: The 1800 Series offers operating frequencies in 25 kHz steps, while the 3000 Seriesoffers operating frequencies in 125 kHz steps. This means that not every frequency selectable on the 1800 Series components will be selectable on the 3000 Series components. Set each transmitter-receiver pair to identical frequencies.4
Quick Overview of System OperationThank you for purchasing this Audio-Technica 1800 Series Dual-channel Camera-mountUHF Wireless Microphone System. All 1800 Series systems are designed primarily to be usedwith video cameras, with the ATW-R1820 dual-channel receiver mounted on a camera and connected to the camera's audio input; the systems may also be used with other componentsequipped with microphone-level input(s).This system is equipped with a dual receiver, which consists of two completely independentreceiver channels in a single unit, for simultaneous operation of two microphones. First, insert batteries (see Battery Installation, page 8 ). Note: The ATW-R1820 dual-channelreceiver also functions without batteries if connected to an external power supply (12V DC source, 500 mA nominal current, not included).Next, attach the antennas to the antenna input jacks, and mount the ATW-R1820 dual-channelreceiver to your camera (mounting hardware not included); or use the included pouch with beltclip to attach the ATW-R1820 to your belt. Connect the output cable(s) to the ATW-R1820 andyour video camera (and/or audio mixer). (See Output A, Output B, and Output Select Switch,page 7.)Turn the ATW-R1820 Power Switch on. Choose “1” to activate only Receiver Channel 1 andOutput A (Power/Peak LED 1 should light red); this option will increase useable battery life.Choose “Both” to activate both receiver channels and both outputs (Power/Peak LEDs 1 and 2should light red). (See Power Switch with four positions: External, Off, 1, Both, page 6.)Select a frequency for Receiver Channel 1 and Receiver Channel 2. (See Selecting Frequencieson your Receiver, page 8.) NOTE: Receiver Channel 1 and Receiver Channel 2 must be set to different frequencies toavoid interference. Transmitter-Receiver pairs must be set to identical frequencies: setTransmitter 1 to the same frequency as Receiver Channel 1; set Transmitter 2 to the samefrequency as Receiver Channel 2.If your system is equipped with a UniPak®Body-pack Transmitter and lavalier microphone:Plug the included lavalier microphone(s) into the UniPak®body-pack transmitter(s) and positionmicrophone(s) on your subject about six inches below the chin. Anticipate movements that maycause the microphone to rub against or be covered by clothing, and position the microphone toavoid it. Turn the power on, select a frequency and choose other settings. (See Operating theTransmitter, page 12. ) If your system is equipped with a Plug-on Transmitter:Attach a microphone (dynamic or condenser) to the plug-on transmitter’s input connector (see Microphone Input, page 11). The transmitter provides power to condenser microphonesrated to operate on 12V phantom power or less. Turn the power on, select a frequency andchoose other settings. (See Operating the Transmitter, page 12.)5
ATW-R1820 Dual-channel Receiver Controls (front panel)Liquid Crystal Display shows battery status and frequency settings. (Use the Dual-channelControl Switch (6) to select frequencies for Receiver Channel 1 and Receiver Channel 2; in Hold position, only Receiver Channel 1 frequency appears in LCD.) Battery meter is onlyactive when Dual-channel Control Switch is in the Hold position.BNC-type antenna connectors. Antennas A & B (split internally) both provide signals forReceiver Channel 1 and Receiver Channel 2. Attach the antennas to the antenna input jacks.Make certain that during operation there is a clear open-air path between the receiver antennasand the transmitters.True Diversity operation: two antennas feed two completely independent RF sections on thesame frequency for each receiver; automatic logic circuitry selects the superior signal.Diversity Indicator 1 indicates which tuner has the better reception and is in operation forReceiver Channel 1; Diversity Indicator 2 indicates which tuner has the better reception and isin operation for Receiver Channel 2. Turns the unit on and off.Choose “Ext”, if the unit is connected to an external power supply (12V DC source, 500 mAnominal current, not included). In “Ext” position, both receiver channels and both outputs areactivated (indicated by illumination of Power/Peak LEDs 1 and 2). Choose “Off” to turn the unit off.Choose “1” to activate only a single receiver channel (Receiver Channel 1/Output A, indicated by the illumination of Power/Peak LED 1). This conserves energy if you are only using one audio channel. Choose “Both” to activate both receiver channels and both outputs (indicated by illumination ofPower/Peak LEDs 1 and 2). Note: Selected receiver will be muted unless Dual-channel Control Switch (6) is in Hold position.Indicates which receiver channel(s) is (are) in operation. Also indicates receiver overload byturning off; too much signal will cause blinking LED (off during peaks). To correct overload,adjust audio gain on transmitter. (See Audio Input Level (Gain) Adjustments, page 13.)This switch allows you to use the single LCD window to control each of the two receiver channels separately.To set frequency for Receiver Channel 1, switch to 1 (left position). To set frequency for Receiver Channel 2, switch to 2 (right position).To lock settings and operate unit, switch to Hold (center position).Note: Receiver Channel 1 is muted when switch is at 1; Receiver Channel 2 is mutedwhen switch is at 2; both channels un-mute when switch is at Hold. This LED is red when switch is in position 1, indicating muted operation for Receiver Channel 1.It is also red when switch is in position 2, indicating muted operation for Receiver Channel 2.LED turns green in Hold position, indicating unit is ready for operation.Use with the Dual-channel Control Switch and Up/Down arrows to choose operating frequenciesmanually or automatically (using your choice of three automatic scan groups).Press Up or Down arrows, in conjunction with the Set button, to choose operating frequenciesmanually or automatically (using your choice of three automatic scan groups).LCDAntenna Input JacksDiversity Indicators for each antenna for each receiverPower Switch with four positions: External, Off, 1, BothPower/Peak LEDDual-channel Control Switch with three positions: 1, Hold, 2Dual-channel Control LEDSetUp/Down Arrows 1234567892361 7 23 45698
Output AOutput BOutput Select SwitchReceiver Level Controls (1 and 2)Monitor Select SwitchMonitor Level Control DC Input Monitor Output(rear panel)Balanced Audio Output Jack: TA3M-type connector. Pin 1: ground (shield); Pin 2: “audio +”;Pin 3: “audio -”. Use the included TA3F to XLRM interface cable to connect the receiver outputto a balanced microphone-level input on a camera, mixer or integrated amplifier. Balanced Audio Output Jack: TA3M-type connector. Pin 1: ground (shield); Pin 2: “audio +”; Pin 3: “audio -”. Use the included TA3F to XLRM interface cable to connect the receiver outputto a balanced microphone-level input on a camera, mixer or integrated amplifier. The rear panel provides two balanced audio outputs (Outputs A & B). The unit is equipped withan output select switch that assigns a signal to each of the audio outputs, as follows:Output A (left) can be assigned either Receiver Channel 1 or Mix. (Mix = Ch. 1 and Ch. 2 signals mixed together. The relative levels of each signal can be adjusted using the individualreceiver level controls.)Output B (right) can be assigned either Receiver Channel 1, Receiver Channel 2, or Mix.Note: Output B is not active when Power Switch is in “1” position.Typical configuration: Output A is assigned Channel 1; Output B is assigned Channel 2, feedingindividual channels in a mixer or camera. Many other options are available, providing much flexibility. For instance:• If your camera doesn’t accept two inputs, you can sum the signal from both transmitters in Output A and connect this mixed signal to your camera.• You can connect Output A (mixed signal) to a camera, and Output B (mixed signal) to an audio mixer. • When using the unit with a single transmitter with both outputs active (Power Switch set at Both), Output A can be used to feed a camera, while Output B can feed an audio mixer (both with identical signals from Receiver Channel 1).The signal levels of each receiver signal (Receiver Channel 1 and Receiver Channel 2) may be adjusted using these controls. When the outputs are assigned to a single receiver signal,these controls will adjust the output level. (Turn clockwise to increase output level.) When theoutputs are assigned to Mix, these controls adjust the relative levels between the receiver signals. This switch assigns a signal to the monitor headphone output. • Choose 1(left position) to hear Channel 1 in both ears (mono signal, stereo output); • Choose 2(right position) to hear Channel 2 in both ears (mono signal, stereo output); • Choose OUT (middle position), to hear Output A in the left ear, and Output B in the right ear.The level control (volume control) for headphones is independent of other level controls. Turn to the right to increase the volume.You may connect the unit to an external power supply (12V DC source, 500 mA nominal current, not included). In this case, move the Power Switch to the “Ext” position; both receiv-er channels are activated (indicated by illumination of Power/Peak LEDs 1 and 2). 1/4" TRS jack. 7101714 1116 13 151011125613141516171312 12PIN 1 PIN 3PIN 2
ATW-R1820 Dual-channel Receiver BatteriesEach ATW-R1820 dual-channel receiver uses six 1.5V AA batteries, not included. Alkaline type isrecommended. Always replace all batteries. Make certain the receiver power is Off beforereplacing batteries. Note: The ATW-R1820 receiver also functions without batteries if connectedto an external power supply (12V DC source, 500 mA nominal current, not included).1. Open the battery compartment door by pushing the catch back. 2. Observe correct polarity as marked and carefully insert six fresh 1.5V AA alkaline batteries (see above).3. Replace the door, making certain the latch clicks securely in place.After the batteries are installed, turn the power on by moving the Power Switch to either the 1or Both position. The small red power-on LED(s) (see aat left ) should light (red light at 1 if PowerSwitch is in position 1; red light at 1 and 2 if Power Switch is in Both position) and the LCD windowshould come on. If this does not happen, the batteries are installed incorrectly or they are depleted. The receiver’s “fuel gauge” battery indicator (see bat left ) displays a maximum of four bar segments. When LCD flashes “LOW.BAT”, the batteries should be replaced immediately toensure continued operation. Note: Battery indicator is only visible in the “Hold” position.Operating the ReceiverNOTE: Receiver Channel 1 and Receiver Channel 2 must be set to different frequencies toavoid interference. Transmitter-Receiver pairs must be set to identical frequencies: setTransmitter 1 to the same frequency as Receiver Channel 1; set Transmitter 2 to the samefrequency as Receiver Channel 2.Overview…1. Turn the power on by moving the Power Switch to either the 1 position (for single-channel operation) or Both position (for dual- channel operation). 2. Switch the Dual-channel Control Switch to 1 (to set frequency for Receiver Channel 1) or 2 (to set frequency for Receiver Channel 2). Audio output is muted for the channel that is selected.3. Press the Set button to enter the Frequency Selection Menu mode; the word “MENU” will appear.4. Use the Up/Down arrows to cycle through functions: - first arrow up is Manual Frequency Selection mode; - second arrow up is Automatic Scan Group 1; - third arrow up is Automatic Scan Group 2; - fourth arrow up is Automatic Scan Group 3; - fifth arrow up is Quit, allowing exit from Menu mode. First…Turn the power on by moving the Power Switch to Both (for dual-channel operation). To set frequency for Receiver Channel 1, switch Dual-channel Control Switch to 1 (left position). 1. Press Set button. The word “MENU” will appear. Press Up arrow to show current frequency.Press Set button and frequency will begin to flash; then use up and down arrows to adjust the frequency. Frequency changes in 25 kHz steps. To increase scroll speed, hold the Up or Down arrow for more than 4 seconds. 2. When you arrive at desired frequency, press and hold the Set button until the word “STORED”appears. Frequency is now set. Battery SelectionBattery InstallationBattery Condition IndicatorSelecting Frequencies on your ReceiverDual-channel Operation (using two transmitters)Setting Receiver Frequency Manually8ab
3. To “back out” of the Manual Frequency Set mode without making a frequency choice, simplypress the Set button once to exit the menu and return the receiver to normal operation. The word “ESCAPE” will appear in the window, and no changes in frequency setting will be made; the receiver's audio output will again be enabled (when Dual-channel Control Switch is returned to Hold position). To set frequency for Receiver Channel 2, switch Dual-channel Control Switch to 2 (right position).Repeat steps 1-2 above.To lock settings and operate unit, switch Dual-channel Control Switch to Hold (center position).Note: While Channel Selection mode is still active, if the Dual-channel Control Switch ismoved back to Hold position before channel selection is complete, LED will remain redand audio will remain muted until the control sequence is completed.First…Turn the power on by moving the Power Switch to Both (for dual-channel operation).Then switch Dual-channel Control Switch to 1 (left position).1. Press the Set button to enter the Frequency Selection Menu mode; the word “MENU” will appear.2. Use the Up or Down arrow to reach Scan 1, Scan 2, or Scan 3. Press the Set button once to select one of these three Scan groups. The word “SCAN1”, “SCAN2” or “SCAN3” will flash in the LCD window. 3. Press the Up or Down arrow to begin the scan. Press the Up arrow to scan up from the lowestfrequency in the group; press the Down arrow to scan down from the highest frequency in the group.4. The first available frequency will flash in the LCD window. To activate this frequency selection,press and hold the Set button until the word “STORED” appears in the LCD window. 5. If you do not wish to use the frequency found, you may press the Up or Down arrow. The Up arrow will scan upwards, the Down arrow will scan downwards, from the frequency you are on.6. To set frequency for Receiver Channel 2 (for dual-channel operation), switch Dual-channel Control Switch to 2 (right position). Repeat steps 1- 4 above. Note: Be certain to select the same Scan Group that you used for Receiver Channel 1. 7. To lock settings and operate unit in dual-channel operation (using two transmitters), switch Dual-channel Control Switch to Hold (center position). The receiver will return to normal operation,audio function will be restored and the Dual-channel Control LED indictor will turn green. 8. If you are using multiple systems, use the same scan group for all receivers. After completing thefirst receiver’s scan and frequency selections, set its transmitters to the appropriate frequencies (see How to Set Frequencies on your Transmitter, page 12 ); leave the transmitters On, and run the next receiver’s automatic scan function. Always set a receiver-transmitter pair to the same frequency before using the automatic scan function to select frequencies for the next receiver.In the event that no more free frequencies are available within the scan group, the receiver willindicate “END” on the receiver display. In this case, select a different scan group for bothReceiver Channels 1 and 2 and re-scan.Note: While Channel Selection mode is still active, if the Dual-channel Control Switch ismoved back to Hold position before channel selection is complete, LED will remain redand audio will remain muted until the control sequence is completed.First…Turn the power on by moving the Power Switch to the 1 position (for single-channel operation).Switch Dual-channel Control Switch to 1 (left position). Output from Receiver Channel 1 is nowmuted. Note: Output B is not active when the Power Switch is in the “1” position.1. Press Set button. The word “MENU” will appear. Press Up arrow to show current frequency.Press Set button and frequency will begin to flash; use up and down arrows to adjust the frequency. Frequency changes in 25 kHz steps. To increase scroll speed, hold the up or down arrow for more than 4 seconds. 2. When you arrive at desired frequency, press and hold the Set button until the word “STORED” appears. Frequency (which appears on the screen) is now set.3. To “back out” of the Manual Frequency Set mode without making a frequency choice, simplypress the Set button once to exit the menu and return the receiver to normal operation. The word “ESCAPE” will appear in the window, and no changes in frequency setting will be made; the receiver's audio output will again be enabled.To lock settings, un-mute and operate the unit, switch Dual-channel Control Switch to Hold(center position). Using the Automatic Scan Function to Set Receiver Frequency (dual-channel operation)Single-channel Operation (using one transmitter)Setting Receiver Frequency Manually9
First…Turn the power on by moving the Power Switch to 1 (for single-channel operation). Then switchDual-channel Control Switch to 1 (left position). Note: Output B is not active when PowerSwitch is in the “1” position.1. Press the Set button to enter the Frequency Selection Menu mode; the word “MENU” will appear.2. Use the Up or Down arrow to reach Scan 1, Scan 2, or Scan 3. Press the Set button once to select one of these three Scan groups. The word “SCAN1”, “SCAN2” or “SCAN3” will flash in the LCD window. 3. Press the Up or Down arrow button to begin the scan. Press the Up arrow to scan up from the lowest frequency in the group; press the Down arrow to scan down from the highest frequency in the group.4. The first available frequency will flash in the LCD window. To activate this frequency selection,press and hold the Set button until the word “STORED” appears in the LCD window. 5. If you do not wish to use the frequency found, you may press the Up or Down arrow. The Up arrow will scan upwards, the Down arrow will scan downwards, from the frequency you are on. 6. To lock settings and operate unit in single-channel operation (using one transmitter), switch Dual-channel Control Switch to Hold (center position). The receiver will return to normal operation, audio function will be restored and the Dual-channel Control LED indicator will turn green. Using the Automatic Scan Function to Set Receiver Frequency(single-channel operation)10
AntennaPower-on LEDLCDAudio Input JackMicrophone InputPower/Mute ButtonUp/Down ArrowsSet ButtonSliding Control Cover(3-position)Sliding Control CoverBattery DoorMounting ClipAT W -T1801 UniPak®Body-pack &AT W -T1802 Plug-on Transmitter ControlsThe ATW-T1801 UniPak®body-pack transmitter includes a field-replaceable flexible antenna. Forbest results, allow the antenna to hang freely and full length from the bottom of the transmitter.If the received signal is marginal, experiment with different transmitter positions or try reposi-tioning the receiver. Since the transmitter antenna simply screws in, check to make certain it issnugly attached (finger-tight). Do not change the length of the transmitting antenna.Green light indicates power is on and un-muted; red light indicates that audio is muted.The light will blink when the batteries are low.Liquid Crystal Display presents setup and operating information. The LCD in the transmitters isdesigned for greatest contrast and best viewing with the window rotated somewhat away fromthe viewer (about 30 degrees), not straight-on, for a more convenient holding/viewing position. The display is illuminated with a backlight when you press Set to access transmitterfunctions. The backlight will automatically turn off within a set period of time.Connect an audio input device (microphone or guitar cable) to the audio input jack on the bottomof the ATW-T1801 UniPak®Body-pack Transmitter. A number of Audio-Technica professionalmicrophones and cables are available separately, pre-terminated with a compatible input connector (see page 14 ). The cable connector latches automatically when inserted into the transmitter jack. To unlatch and remove the connector, pull up on the connector’s knurled metal collar.The ATW-T1802 plug-on transmitter has a 3-pin XLRF-type input connector with a locking collar.Use either a dynamic or a condenser microphone. The transmitter provides power to condensermicrophones rated to operate on 12V phantom power or less. To attach the microphone, rotatethe threaded locking collar fully clockwise (“down”) until it reaches the transmitter housing (seeaat right). Press the microphone and transmitter together (see bat right). Rotate the thread-ed collar “up” until it is firmly against the end of the mic (see cat right). Make certain the micis securely attached before use. To detach the microphone, reverse the steps above. Alwaysloosen the threaded collar fully before attempting to disconnect the mic.For on/off and mute functions.Press Up or Down arrows, in conjunction with the Set button, to choose operating frequenciesand access transmitter functions.Use in conjunction with the Up/Down arrows, to choose operating frequencies and accesstransmitter functions.This 3-position sliding cover on the body-pack transmitter’s control panel prevents accidentalshut-off or channel-switching.This sliding cover on the plug-on transmitter’s control panel helps to prevent accidental shut-off or channel-switching.Open by sliding the catch down (on body-pack) or pushing in direction of arrow (on plug-on transmitter).The ATW-T1801 UniPak®transmitter’s mounting clip may be installed with the case positionedeither “up” or “down,” depending upon which is preferred for the application. To turn the cliparound, spring the ends of the clip out of the two holes on the sides of the transmitter case andreinstall it facing in the opposite direction.11POWER/MUTESETPOWERMUTESETATW-T1801 UHF TRANSMITTER1234567891011126245623317788910111112abc
Battery SelectionTransmitter Battery InstallationBattery Condition Turning your Transmitter On & OffHow to Set Frequencieson your TransmitterHow to Access & Use the Function Menu on your TransmitterPOWERMUTESETATW-T1801 UHF TRANSMITTERPOWER/MUTESETTransmitter BatteriesEach transmitter uses two 1.5V AA batteries, not included. Alkaline type is recommended.Always replace both batteries. Make certain the transmitter power is Off before replacing batteries.1. Open the battery compartment door by sliding the catch down (on body-pack) or pushing in direction of arrow (on plug-on transmitter). 2. Observe correct polarity as marked on the metal contacts on the door and carefully insert two fresh 1.5V AA alkaline batteries.3. Close the door, making certain the latch clicks securely in place.After the batteries are installed, turn the power on by pressing and holding the Power/Mute button. The small power-on LED (see aat left ) should light green and the LCD window shouldcome on. If this does not happen, the batteries are installed incorrectly or they are depleted. The transmitter’s “fuel gauge” battery indicator in the LCD displays a maximum of four bar seg-ments. When it flashes “LOW.BAT”, the batteries should be replaced immediately to ensurecontinued operation. (Additionally, the power-on LED will flash when the batteries are low.)Operating the TransmitterTo turn the transmitter on, press and hold the Power/Mute button until the power indicatorlights green, and the LCD window comes on (about 1-2 seconds). The operating frequency willshow in the window after the power-up sequence.To turn the transmitter off, press and hold the Power/Mute button again, until the power indicatorand the LCD window are extinguished (about 1-2 seconds). The LCD window will show “PWR.OFF” before shutdown.NOTE: Transmitter-Receiver pairs must be set to identical frequencies: set Transmitter1 to the same frequency as Receiver Channel 1; set Transmitter 2 to the same frequencyas Receiver Channel 2.1. Turn transmitter on.2. Press the Set button once and the small word “MENU” will appear above the frequency. 3. Press the Set button again and the small flashing word “EDIT” will appear to the right of “MENU”. 4. Use the Up/Down arrows to change the transmitter frequency. Press either arrow for 25 kHzsteps, or hold down either arrow for rapid cycling through the range. Frequencies “wrap around” when the top or bottom of the band is reached. Select the exact frequency displayed on the receiver.5. To activate this frequency selection, press and hold the Set button until the word “STORED”appears in the transmitter’s window. (If you do not wish to complete this selection, just press the Set button once: the word “ESCAPE” will appear briefly in the window and the transmitter will return to the Menu mode.)6. When finished entering a frequency, press the Up arrow once to move to “QUIT”. Then pressthe Set button once to exit the menu. The word “MENU” in the transmitter window will go off, indicating the return to normal operation.1. Turn transmitter on.2. Press the Set button once; the small word “MENU” will appear above the frequency.3. When in the Menu mode, use the Up and Down arrows to cycle through the following functions:• Frequency • Input Select (body-pack only)• RF Power • Reset to Defaults• Audio Input Level • Quit (exit menu)• Power/Mute Locks4. To make a change in the default setting: • Press Set button once; • Press Up or Down arrow until you reach desired setting; • Press and hold Set button until the word “STORED” appears in the LCD window.• (If you do not wish to complete this selection, just press the Set button once: the word “ESCAPE” will appear briefly in the window and the transmitter will return to the Menu mode.)12aATW-T1801 ATW-T1802
Transmitter FunctionsRF Power Adjustments on your TransmitterAudio Input Level (Gain) Adjustments on your TransmitterUsing the Mute and Un-Mute Functions on your TransmitterPower/Mute LocksAudio Input Selector(continued on page 14)13Function Menu Default Setting Choices (Edit) Wrap-around*Frequency Lowest in band 996 frequencies Yes(25 kHz steps)RF Power RF LOW RF LOW, RF HI YesAudio Input Level +6 dB -6 dB, 0 dB, +6 dB, No+12 dB, +18Power/Mute Locks NO.LOC NO.LOC, ALL.LOC, YesMUT.LOC, PWR.LOCInput Select** MIC MIC, INST YesReset to Defaults PRESET See Restore Default –Settings, page 14Quit QUIT Press Set to exit –* Continue in the same Up/Down direction and choices “wrap around” to the other end of the range.** On UniPak®transmitter onlyRF power may be set to “RF HI” (30 mW nominal) or “RF LOW” (10 mW nominal) through thefunction menu. The default setting is “RF LOW”. While the High setting normally provides maximum operating range, the Low setting will help extend battery life. The Low setting mayalso be preferred in multichannel systems, or when operating very close to the receiver, toreduce the possibility of interference or receiver RF overload.Correct adjustment of transmitter audio input, receiver audio output, and mixer/amplifier inputand output levels is important for best performance.A 5-position audio input gain setting, selected through the function menu, allows you to matchthe audio input level to the transmitter for best modulation with minimum distortion. The choicesare +18, +12 dB, +6 dB, 0 dB and -6 dB. The default value is +6 dB. Select the highest settingthat does not result in over-modulation with the highest audio/instrument input levels (an AF indication on the receiver no higher than “0”).When the transmitter is muted, it produces RF with no audio. When the transmitter is un-muted, it produces both RF and audio. To mute the transmitter (cut off the audio, but continue the RF output), press and release the Power/Mute button once. The word “MUTE”will appear in the LCD window, just below the frequency, and the Power-on LED will turn red. To un-mute the transmitter (restore the audio), press and release the Power/Mute button onceagain. The “MUTE” will disappear from the LCD window, and the Power-on LED will turn green.The Power/Mute button can be programmed (through the function menu): power can be lockedOn; Mute can be locked either On or Off. Setting DescriptionNO.LOC The Power and Mute functions operate normally.ALL.LOC Both the Power and Mute functions are locked into their status as of the time “ALL.LOC” is applied. (Power On, and Mute either On or Off.) Note: “ALL.LOC” must be re-accessed and the setting changed to turn the transmitter off.MUT.LOC In “MUT.LOC” mode, the audio cannot be muted. The Power functioning is unaffected. (If “MUT.LOC” is applied while the transmitter is muted, pressing the Power/Mute button once will return to un-muted operation; thereafter the Mute function is disabled until the setting is changed again.)PWR.LOC Power is locked On as of the time “PWR.LOC”is applied. The Mute functioning is unaffected. Note: When in the “PWR.LOC” mode, the transmitter may be turned off by: (1) Re-accessing the .LOC Menu and changing the setting, or (2) Removing and re-installing the batteries. When the transmitter is turned on again, it will power-up in the “NO.LOC” mode. (Only the “PWR.LOC”function will change when batteries are removed; all other settings remain stored in memory.)If an attempt is made to take an action that currently is locked out, the LCD will display “LOC.KED” briefly, then return to its previously-displayed contents.The UniPak®body-pack transmitter provides input connections for both low-impedance (Lo-Z)microphones and high-impedance (Hi-Z) instruments. A wide range of Audio-Technica WirelessEssentials™microphones and cables are available pre-terminated with the appropriate professional latching connector (see page 14 ).Select the desired input – microphone or instrument – through the function menu; “MIC” or “INST” will show in the LCD window, just below the frequency.
Operating the Transmitter (continued)1. A “PRESET” selection in the menu allows you to reset all transmitter functions to their factory-default values.2. Press the Set button once to move to Menu mode.3. Press the Up arrow twice to move to “PRESET” in the LCD window.4. Press the Set button once and “LOAD” will appear in the LCD.5. Press and hold the Set button until “DEF” appears in the LCD.6. Press and hold the Set button until “LOADED” appears briefly in the LCD. The window will then revert to “PRESET”.7. Press the Down arrow once to move to “QUIT”.8. Press the Set button once to exit the Menu mode and return to normal operation, with all factory-default settings restored.Tips for Best Results1. Use only fresh alkaline batteries. Always replace all batteries. Do not use “general purpose” (carbon-zinc) batteries.2. Position the dual-channel receiver so that it has the fewest possible obstructions between it and the normal location of the transmitters. Line-of-sight is best.3. The transmitters and the dual-channel receiver should be as close together as conveniently possible, but no closer together than three feet.4. The receiver antennas should be in the open and away from any metal.5. Each transmitter-receiver pair must be set to the same frequency. 6. Only one transmitter on a given frequency should be “on” at a time.7. The power switch on the transmitter has four positions: “Ext.,” “Off”, “1” and “Both.” 8. If the “Out Level” of either receiver channel is set too high, it may over-drive the input of the camera/mixer or clip the output of the receiver, causing distortion. Conversely, if the receiveroutput is set too low, the overall signal-to-noise ratio of the system may be reduced.9. You need to change channels 1) when a strong interference signal is received, 2) when the channel breaks down, or 3) during multiple-system operation in order to select an interference-free channel. Always turn the units off before changing frequencies.10. Turn the receiver and transmitter off when not in use. Remove the batteries during long-term storage.Available AccessoriesAT829cW Cardioid condenser lavalier microphoneMT830cW Omnidirectional condenser lavalier microphoneMT830cW-TH “Theater” model, same as MT830cW except beige-color mic and cableAT831cW Cardioid condenser lavalier microphoneAT889cW Headworn noise-cancelling condenser microphoneAT892cW MicroSet®headworn omnidirectional condenser microphone AT892cW-CO Same as AT892cW except cocoa-color mic, earset and cableAT892cW-TH “Theater” model, same as AT892cW except beige-color mic, earset and cableAT898cW Subminiature cardioid condenser lavalier microphoneAT899cW Subminiature omnidirectional condenser lavalier microphoneAT899cW-TH “Theater” model, same as AT899cW except beige-color mic and cableATM350cW Cardioid condenser instrument microphoneATM73cW Headworn cardioid condenser microphoneATM75cW Headworn cardioid condenser microphonePRO 8HEcW Headworn hypercardioid dynamic microphonePRO 35cW Cardioid condenser instrument microphoneU851cW Cardioid condenser boundary microphoneU857ALcW Cardioid condenser gooseneck microphoneAT-GCW Hi-Z instrument/guitar cable with 1/4" phone plugXLRW Connecting cable for UniPak®transmitter with an XLRF-type input connector, for Lo-Z microphones with XLRM-type output terminationsRF Cables Low-loss design, 50 ohm impedance, with BNC-to-BNC connectors:AC12 RG58-type cable (12')AC25 RG8-type cable (25')AC50 RG8-type cable (50')AC100 RG8-type cable (100')ATW-RMS1 Remote mute switch designed to be installed between a wireless microphone using an HRS-type connector and its associated body-pack wireless transmitterATW-RCS1 Remote momentary-mute/cough switch designed to be installed between a wireless microphone using an HRS-type connector and its associated body-pack wireless transmitterVisit www.audio-technica.com for detailed information on all of our wireless accessories.14Restore Default SettingsWireless Essentials®Microphones and Cables(all Wireless Essentials accessories are terminated for use with UniPak®transmitters)Receiver AccessoriesTransmitter Accessories
15Overall SystemATW-R1820 Dual-channel ReceiverATW-T1801 UniPak®Body-pack TransmitterATW-T1802 Plug-on TransmitterSpecifications†UHF Operating FrequenciesBand C: 541.500 to 566.375 MHzBand D: 655.500 to 680.375 MHzNumber of Operating Frequencies 996 total per band (25 kHz increments)Frequency Stability ±0.005%, Phase Lock Loop frequency controlModulation Mode FMNormal Deviation ±10 kHzOperating Range 100 m (300') typicalOperating Temperature Range 23˚ F (-5˚ C) to 113˚ F (45˚ C)Frequency Response 70 Hz to 15 kHzReceiving System Dual independent RF sections, automatic-switching diversityImage Rejection >50 dB typicalSignal-to-Noise Ratio 104 dB at 30 kHz deviation (A-weighted),maximum modulation 37 kHzTotal Harmonic Distortion <1% (±10 kHz deviation at 1 kHz)Sensitivity 25 dBµV, (S/N 60 dB at 5 kHz deviation, A-weighted)Audio Output (balanced) 27 mV (at 1 kHz, ±5 kHz deviation)Output Connector 3- pin mini XLR (TA3M-type)Monitor Headphone Output (typical) 35 mW max., 32 ohm load (per channel) Monitor Headphone Jack 3.5 mm TRS, signals on both Tip and RingExternal Power Requirements 12V DC nominal, 500 mABatteries (not included) Six 1.5V AA alkalineCurrent Consumption (battery)Dual-channel Operation 600 mA typicalSingle-channel Operation 350 mA typicalBattery LifeDual-channel Operation 6 hours typical*Single-channel Operation 10 hours typical** depending on battery type and use patternDimensions 85.0 mm (3.35") W x 133.0 mm (5.24") H x 36.0 mm (1.42") DNet Weight (without batteries) 425 grams (15.0 oz)Accessories Included Two flexible UHF antennas; two 18" TA3F to XLRMoutput cables; belt pouchRF Power Output High: 30 mW; Low: 10 mW, nominalSpurious Emissions Under federal regulationsDynamic Range >105 dB, A-weightedInput Connections High impedance, low impedance, biasBatteries (not included) Two 1.5V AA alkalineCurrent Consumption High: 180 mA; Low: 160 mA, typicalBattery Life Approximately 6 hours (High); 8 hours (Low),depending on battery type and use patternDimensions 66.0 mm (2.60") W x 87.0 mm (3.43") H x 24.0 mm (0.94") DNet Weight (without batteries) 80 grams (2.8 oz)RF Power Output High: 30 mW; Low: 10 mW, nominalSpurious Emissions Under federal regulationsDynamic Range >105 dB, A-weightedInput Connector 3-pin locking XLRF-typeMicrophone Power Provides power to condenser microphones rated tooperate on 12V phantom power or less. Batteries (not included) Two 1.5V AA alkalineCurrent Consumption High: 180 mA; Low: 160 mA, typicalBattery Life Approximately 6 hours (High); 8 hours (Low),depending on battery type and use patternDimensions 40.0 mm (1.57") x 111.0 mm (4.37") x 40.0 mm (1.57")Net Weight (without batteries) 199 grams (7.0 oz)† Specifications are subject to change without notice.
One-Year Limited WarrantyAudio-Technica professional wireless systems purchased in the U.S.A. are warranted for oneyear from date of purchase by Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly withoutcharge or, at our option, replaced with a new product of equal or superior value if delivered toA.T.U.S. or an Authorized Service Center, prepaid, together with the sales slip or other proof ofpurchase date. Prior approval from A.T.U.S. is required for return. This warranty excludes defectsdue to normal wear, abuse, shipping damage, or failure to use product in accordance with theinstructions. This warranty is void in the event of unauthorized repair or modification, or removalor defacing of the product labeling.For return approval and shipping information, contact the Service Dept., Audio-Technica U.S.,Inc., 1221 Commerce Drive, Stow, Ohio 44224.Except to the extent precluded by applicable state law, A.T.U.S. will have no liability for any consequential, incidental, or special damages; any warranty of merchantability or fitness for particular purpose expires when this warranty expires.This warranty gives you specific legal rights, and you may have other rights which vary fromstate to state.Outside the U.S.A., please contact your local dealer for warranty details.Audio-Technica U.S., Inc.1221 Commerce Drive, Stow, Ohio 44224 (330) 686-2600 www.audio-technica.comP52016 ©2007 Audio-Technica U.S., Inc. Printed in U.S.A.

Navigation menu