Asiatelco Technologies EC-P11 Wireless Energy Controller User Manual EC P11 ver2

Asiatelco Technologies Co. Wireless Energy Controller EC P11 ver2

EC-P11 user manual-ver2

1 / 13 www.asiatelco.com Wireless Energy Controller V1.8 model number：EC-P11 INDEX 1 DESCRIPTION --------------------------------------------------------------------------------------------- 3 2 BENEFIT ---------------------------------------------------------------------------------------------- 4 3 FEATURES ---------------------------------------------------------------------------------------------- 4 4 HARDWARE CONFIGURATION ---------------------------------------------------------------------- 5 5 ELECTRICAL SPECIFICATION ---------------------------------------------------------------------- 5 6 SIGNAL DEFINE ----------------------------------------------------------------------------------------- 7 7 DIMENSION ----------------------------------------------------------------------------------------------- 8 8 QUICK USER GUIDE ------------------------------------------------------------------------------------ 9 9 SOFTWARE USER GUIDE ------------------------------------------------------------------------------ 10
2 / 13 www.asiatelco.com IMPORTANT ANNOUNCEMENT **Highvoltageinthecontroller,operatorsmustbewithprofessionalknowledge.**Thewirenamed“E‐gnd”mustbeconnectedwiththeearthgroundallthetime. FCCWarningInformationThisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.NOTE:***WIFIChannel12&Channel13isnotavailableinfinalproduct.Thehardwareisdisabledinside.***ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:—Reorientorrelocatethereceivingantenna.—Increasetheseparationbetweentheequipmentandreceiver.—Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.—Consultthedealeroranexperiencedradio/TVtechnicianforhelp.***Besuretoleavethehumanbodymorethan20cmwhenusingthisproduct.***Thecountrycodeisnotsupportedbythisproduct.
3 / 13 www.asiatelco.com 1 DESCRIPTION The Wireless Energy Controller （model number：EC-P11）works as a controller with LED-fixture, and achieve remote control through WIFI wireless. The controller has 2* 0-10V signal for dimming usage, and current sensor is also integrated.
4 / 13 www.asiatelco.com 2 BENEFIT ---- Control and Schedule ON/OFF/DIM for individual fixture or groups of fixtures ---- Remote control and self programmable control mode ---- Customer defined continuous dimming ---- Adjust ON/OFF times and night trimming schedules ---- Monitor the work status & the Energy consumption of every fixture in every minute ---- Track burn hours to verify LED fixture life ---- Detect LED fixture malfunctions remotely ---- Works with any manufactures’ outdoor LED lighting fixture ---- Reduce Energy Costs ---- Reduce Carbon Emission ---- Reduce Manpower Costs ---- Reduce Maintenance Costs 3 FEATURES ---- Each device can works in Node/Hub/Mix-mode ---- Wide AC input flexibility, 110V/AC, 277 V/AC, 480V/AC ---- AC switch inside（ Low loss in AC switch, typical 16 mΩ） ---- Max output power 1000W ---- 2* 0-10V Dimming signal for LED-fixture ---- AC Current Sensor integration ---- 1*10M/100M Ethernet port ---- WIFI 802.11b/g/n ---- Ublox GPS ---- 1*Button for customer ---- 1*USB device port (reserved ) ---- 4*LED for work status indicated ---- 1* Interface for General Interrupt input (reserved) ---- 1* Interface for ADC signal input (reserved) ---- 12V/0.5A DC power output (reserved) ---- Easy to install & configure
5 / 13 www.asiatelco.com 4 HARDWARE CONFIGURATION HARDWARE CONFIGURATION STANDARD LIST RemarkWIFI & WIFI antenna port GPS & GPS antenna port 1 * 0-10V Dimming signal output 1 * AC switch inside OPTIONAL LIST 2nd * 0-10V Dimming signal output 2nd * AC switch Interface for Motion sensor input (reserved , not available now )Interface for Light sensor input (reserved , not available now )1*USB device port (reserved , not available now ) 5 ELECTRICAL SPECIFICATION AC/AC PART Absolute Maximum Ratings Items Unit Value Max input value V / AC 500 Max output current A 2 Max output power W 1000 Operating Temperature Range ℃ -40℃ to 85℃ Storage Temperature Range ℃ -65℃ to 145℃ Electrical Characteristics
6 / 13 www.asiatelco.com Items Unit ValueNominal input value V / AC 277 Input value range V / AC 100V/AC to 500V/AC AC Input Frequency range Hz 50 / 60 Switch Output value V / AC same value as input Accuracy of AC current sensor ±10% RMS (load current<150mA) ±5% RMS (load current>150mA) GPS SPECIFICATION Items SPEC Receiver type 50 channel GPS L1 C/A TTFF Cold start-----29 s Warm start-----28 s Hot start-----2 s Sensitivity tracking: -160 dBm acquisition: -147 dBm Horizontal position accuracy * ＜ 10 meters * Test environment: Open sky, 24 hours static, Qty of satellite>6, all of satellite signal strength>-130dBm
7 / 13 www.asiatelco.com 6 SIGNAL DEFINE
8 / 13 www.asiatelco.com 7 DIMENSION
9 / 13 www.asiatelco.com 8 QUICK USER GUIDE Case—drive 1xFixture Case—drive 2xFixture
10 / 13 www.asiatelco.com 9 SOFTWARE USER GUIDE  Software Architecture  Important Function Using  system() SYNOPSIS #include <stdlib.h> int system(const char *command);  ioctl() SYNOPSIS #include <sys/ioctl.h> int ioctl(int d, int request, ...);  UART Interface  Baud rate setting #include <stdlib.h> system("gpio U 115200 "); // Set Baud rate 115200  Read int fd ; unsigned char buf[1024]; fd = open(“/dev/ttyS0”, O_RDWR); read (fd, buf,1024); close(fd);  Write int fd ; unsigned char buf[1024]; fd = open(“/dev/ttyS0”, O_RDWR |O_NONBLOCK | O_SYNC |O_NOCTTY);
11 / 13 www.asiatelco.com write (fd, buf,1024); close(fd);  ADC Interface  Spi read  Spi write  ADC read code  DAC Interface  Source code #include <stdlib.h> Command: system("softspicmd 13 chn value"); Explain: chn: 0~2 0 select DAC channel A2 1 select DAC channel A1 2 select DAC channel A1&A2 value: 0~4095 0~10V Command: system("softspicmd 15"); Explain : Executes a software clear (all CODE and DAC registers cleared to their default values) Command: system("softspicmd 16"); Explain : Executes a software reset (all CODE, DAC, and control registers returned to their default values) Command: system("softspicmd 21 value "); Explain :
12 / 13 www.asiatelco.com This command will simultaneously writes data to all CODE registers while updating all DAC registers. It means channel A and channel B will simultaneously update to set value. value: 0~4095 0~3.3V  USB Interface  Read Source Code: int fd ; unsigned char buf[1024]; fd = open(“/dev/ ttyUSB0”, O_RDWR); read (fd, buf,1024); close(fd);  Write Source Code: int fd ; unsigned char buf[1024]; fd = open(“/dev/ttyUSB0”, O_RDWR); write (fd, buf,1024); close(fd);  GPIO Interface  Switcher Swith S1 GPIO number is “GPIO9” Swith S2 GPIO number is “GPIO13” Using methods refer to GPIO write. • gpio w [num]: Set gpio high level. GPIO is output mode. [num] 0 to 46 • gpio c [num]: Set gpio low level. GPIO is output mode. [num] 0 to 46 GPS On/Off GPIO number is “GPIO60” High Level: Open GPS Power Current sensor On/Off To achieve in the future Light sensor On/Off To achieve in the future LED fixture On/Off Channel 1: GPIO number is “GPIO9” High Level: Open GPS Power Channel 2: GPIO number is “GPIO13” High Level: Open GPS Power Indicator LED Read LED: GPIO number is “GPIO41” Yellow LED: GPIO number is “GPIO42” Green1 LED: GPIO number is “GPIO43” Green2 LED: GPIO number is “GPIO44”  NV Interface  NV Write Interface nvram_set(RT2860_NVRAM, "UserStingID", "UserStingContent"); Instructions: RT2860_NVRAM: fixed value. "UserStingID": name of user sting. "UserStingContent": content of user sting.  NV Read Interface char * UserStingContent = nvram_get(RT2860_NVRAM, " UserStingID "); Instructions: RT2860_NVRAM: fixed value. "UserStingID": name of user sting. "UserStingContent": content of user sting.
13 / 13 www.asiatelco.com  GPS Interface //i2ccmd i fd int open_fd(void) { char nm[16]; int fd; snprintf(nm, 16, "/dev/%s", I2C_DEV_NAME); if ((fd = open(nm, O_RDONLY)) < 0) { perror(nm); exit(fd); } return fd; } int ValGetNmeaData (unsigned char * data) { int fd = -1; fd = open_fd(); if (fd < 0) { return -1; } if (ioctl(fd, RT2880_I2C_READ_GPS_DATA, data) < 0) { perror("ioctl"); close(fd); return -1; } close(fd); return 0; } Data: input array[] for get data. The max size is 2048. Example: $GPRMC,,V,,,,,,,,,,N*53 $GPVTG,,,,,,,,,N*30 $GPGGA,,,,,,0,00,99.99,,,,,,*48 $GPGSA,A,1,,,,,,,,,,,,,99.99,99.99,99.99*30 $GPGSV,1,1,00*79 $GPGLL,,,,,,V,N*64 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ The end, thanks ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 2014/03

Navigation menu