Asian Express PL1060-T Remote Controller for Toy User Manual AIRCOMBAT 2013

Asian Express Holding Ltd Remote Controller for Toy AIRCOMBAT 2013

Manual.pdf

USER MANUALTHIS PACKAGE CONTAINS:Colors and styles may slightly vary.WARNING: Never leave product charging unattended for extended periods of time. Always disconnect helicopter from charger immediately after the helicopter is fully charged. Please refer to enclosed safety instructions.Made in ChinaConforms to safety requirements of ASTM, CPSIA and FCC. CHOKING HAZARD - Small parts. Not suitable for children under 3 years.Spare Parts Instruction Manual11HelicopterAIR COMBATLaser Battling Motion Control HelicopterPROPEL RC™ and AIR COMBATTM are trademarks of Rooftop Brands.15760 W Hardy Rd Suite 400 Houston Texas 77060  tel: 949.566.9573  © 2013 Rooftop Brands™.  All Rights Reserved. www.propelrc.com .USB charging cordController
1TABLE OF CONTENTS Features.......................................................................................... 1Remote Battery Installation..................................................................... 2Charging the Helicopter......................................................................... 2Helicopter diagram, Remote Control diagram..................................................... 3Preparing for Flight ............................................................................. 4How to Sync your Helicopter ...................................................................... 4Demonstration Mode............................................................................. 4Flying Tips.............................................................................................. 4Understanding Helicopter Trim Adjustments..................................................... 5Basic Flight Controls.............................................................................. 5Interactive Battle Modes..........................................................................6Helicopter Warning And Safety Precautions......................................................6Part Replacement Instructions.................................................................... 7Contents.......................................................................................... 7Air Combat Propeller System.................................................................. 7Replacing the Upper Propeller Blade........................................................... ..8Replacing the Bottom Propeller Blade...........................................................8Battery Warnings................................................................................. 9Care and Maintenance...........................................................................9FCC Information................................................................................... 9FEATURES• Advanced technology gives you more real-flight maneuvers and battle action  • Using infrared laser technology, the copter “shoots” other Combat Copters • Side counter lights illuminate with each “hit” as the copter performs a spin  • After a third “strike,” the defeated copter slowly spirals to a landing and inactivates the remote control–game over • Makes its own shooting sounds• Remote-controlled copters have their own frequencies to avoid interference • Built-in gyroscopic chip gives it ultra-stable flight2Thank you for purchasing the AIR COMBAT™ Laser Battling Motion Control Helicopter. Please read this instruction booklet carefully as it contains valuable information on how to properly fly and care for your helicopter.REMOTE CONTROL BATTERY INSTALLATION1. Twist off the battery cover from the remote control.2. Install 4 “AAA” alkaline batteries as shown in the diagram.3. Replace the battery cover.Battery Compartment(4 “AAA”  batteries)CHARGING THE HELICOPTER1.  Make sure the helicopter’s power switch is in the “OFF” position and plug the USB charging cord into the charging      socket(see diagram A ).    Note: Do not force press the charging head into helicopter charging socket.2.  Connect the helicopter charging cord to your computer’s USB port (see diagram B).3.  A red LED Light near the copter’s USB port means the helicopter is fully charged. If the red LED light isn’t on, that means      the helicopter is still being charged. (see diagram C).4.  The charging time will vary depending on the amount of charge already stored in your battery. The average charging      time for the battery is approximately 45-60 minutes. Charging socket is located on the underside of the helicopter next to the power switch. Charging cord connects as indicated. Indicator light on charger stays on until charging is complete.B.A. C.IMPORTANT: ALWAYS DISCONNECT CHARGER CORD AFTER CHARGING. NEVER LEAVE CHARGER CONNECTED TO HELICOPTER OVERNIGHT OR FOR EXTENDED PERIODS OF TIME. BatteryCover-  AAA  ++  AAA  -+   AAA   --   AAA   +Red LED light will appear on USBwhen helicopter is charged
HELICOPTER DIAGRAMBelow is a basic list of features and parts on the helicopter.REMOTE CONTROL DIAGRAMBelow is a basic list of features on the infrared wireless remote control.NOTE:  The motion controller come with 2 shape battery department cover, the flat one is for advanced pilot for one hand flying. the half ball cover is for beginner pilot in order to use two hands and feel more stable playing.Stabilizer barTail rotorLanding GearMain Rotor Blades• Verify that there are 4 “AAA” batteries inside the remote control unit and the helicopter has been fully charged.• Make sure your helicopter is turned on and properly synced to your controller. (See “SYNC YOUR HELICOPTER” below)• Make sure to be in a large room with an open radius of at least 25 feet. Close all windows and doors, turn off fans and   close air ducts or any other openings that may cause drafts in the room.• Make sure the room has no obstacles and the highest ceiling possible. DO NOT ATTEMPT TO FLY YOUR HELICOPTER    OUTDOORS. Set your helicopter on a clean flat surface before take-off.Your Air Combat™ utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly side by side in the same wireless range.For One Person Play:1. Before starting, make sure that the power on both your controller and helicopter are in the OFF position.     Make sure that there are no other 2.4G devices in the area as well. 2. Turn ON the helicopter and set it down on a flat surface. The 2 LED indicators on each side of the body     should blink in Red. 3. Turn ON your controller. The 2 LED indicators on each side of the body should now blink in a Red and Blue     alternating fashion. This indicates that your product has been successfully synced. Should this not happen,     repeat all steps again. For Multi Person Play: 4. Before starting, make sure that the power on all Helicopters and Controllers are in the OFF position. Make sure that there are no other 2.4G devices in the area as well.5. Each person will have to sync their helicopter individually at a different time to avoid interference. Follow steps 1 to 3 above making sure to keep away from other people while also making sure that no one else is syncing at the same time. 6. After syncing a players helicopter, it should be left ON until all players have synced their helicopters. 7. Should there be a mistake/interference, all players must turn off their controllers and helicopters and start the process all over again. Before Syncing, your Throttle should always be set to ZERO (All the way down). However, to prevent damage and injury, your helicopter has been fitted with a Safety Mechanism. After syncing your helicopter, a RED indicator light will flash on your controller in a slow pattern. Push the Throttle all the way up and the RED indicator light flashes faster. Pull back the Throttle all the way down and the RED indicator light with turn to a Solid Red. This indicates that you are ready to fly. FLYING TIPS• Operate the helicopter in a wide, indoor space. You should allow at least a 25-foot radius. The helicopter is designed for    INDOOR USE ONLY. • Parental guidance or adult supervision is suggested at all times.• If you are flying the helicopter with others, make sure all spectators are behind you.• For best performance, it is recommended that you operate the helicopter in zero wind conditions. Close all open doors    or windows, and turn off any nearby fans. Wind can greatly affect the performance of the helicopter.SYNCING YOUR HELICOPTER PREPARING FOR FLIGHT 3 4Helicopter Charging Socket Power SwitchBattle Indicator LightPower IndicatorShoot ButtonTrim ControlsPOWER ON/OFFThrottle ControlBattery DepartmentSlow SpeedShoot ButtonFast SpeedShoot SpeedSpeaker
Trim ControlsUNDERSTANDING HELICOPTER TRIM ADJUSTMENTSIf your helicopter’s nose rotates to the left or right uncontrollably, you may need to utilize the TRIM buttons. If your helicopter over-rotates CLOCKWISE (to the right), push and release the LEFT trim button repeatedly until the turning stops and proper flight is maintained. If your helicopter over-rotates COUNTER-CLOCKWISE (to the left), push and release the RIGHT trim button in the same manner until the problem is resolved. From time to time you may have to adjust the left and right trim to ensure the helicopter will fly straight and respond accurately to control commands. 5 6FLIGHT AND CONTROLSBelow is a list of basic flight functions for your Air CombatTM wireless remote-control helicopter. While you’re learning to fly your helicopter, it is best to start with a large room until you get used to the basic controls. If over rotates to the right... If over rotates to the left...LTRIMRPush left trim.RLPush right trim.RLHELICOPTER WARNING AND SAFETY PRECAUTIONSThe helicopter blades revolve at high speeds and can cause damage to the user, spectators and animals. Stand away from the helicopter to reduce the risk of getting into the flight path. Warn spectators that you will be flying your helicopter so that they are aware of its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened to the helicopter.WARNINGS• Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades.• Keep hands, hair and loose clothing away from the propeller when the power switch is turned to the ON position.• Turn off the transmitter and helicopter power switches when not in use.• The remote control charger is built specifically for the helicopter’s Li-poly battery. Do not use it to charge any    other battery.• New alkaline batteries are recommended for maximum performance.• Parental supervision recommended when flying helicopter.IMPORTANT: ALWAYS DISCONNECT CHARGER CORD AFTER CHARGING. NEVER LEAVE CHARGER CONNECTED TO HELICOPTER OVERNIGHT OR FOR EXTENDED PERIODS OF TIME.INTERACTIVE BATTLE MODESGet ready for aerial combat missions with your friends–or “enemies” _(Requires additional Air Combats helicopter.)PREPARATION FOR MISSION:1. Make sure both helicopters are fully charged and ready to fly.2. Sync your helicopter remote to separate?READY, AIM, FIRE!1. While your helicopter’s in flight, aim the front of your helicopter towards the cockpit of your opponent’s     helicopter, and press the SHOOT button on your controller.2. If you score a hit, your enemy’s helicopter will blink its lights and spin once. A slow-flashing red light in the     window of the cockpit indicates that it has been hit once. A faster-blinking light indicates it has been hit twice.3. On the third direct hit, your opponent’s helicopter windows will light up in solid red, and control of their copter will     be lost. The copter will gradually descend safely to the ground. Mission accomplished! 4. The downed helicopter will recover (and reset) after a few moments, and will be ready for the next dogfight.     Pull the trigger back or  release to increase or decrease  the speed of the main rotor and the helicopter will rise up or descend.Tilt the controller down and the helicopter will move forward.Tilt the controller left and the helicopter will turn left.Tilt the controller right and the helicopter will turn right.Tilt the controller up and the helicopter will move backward.
CONTENTS:(1)  1 upper propeller blade                                                        x 1                 (3) 4 connecting rods                  x 4(2) 1 bottom propeller blade                         x 1                (4) 4 screws                  x 4                          Air Combat PROPELLER SYSTEMYour Air Combat propeller system is a precision instrument that may need repair or replacement from time to time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to your Air Combat propeller or propeller connecting rods. TROUBLESHOOTING:If your Air Combat loses its ability to fly correctly, please inspect the propeller system carefully for the following five common issues:1. Replacing Connecting Rod: The connecting rod is a small “handcuff” style device that stabilizes the “upper” propellers. There is one connecting rod on the upper propeller.  Please see Diagram 1. If a connecting rod is broken or missing simply replace it by “peeling” off the existing broken unit and replacing it with a new one. You may have to use slight pressure when reattaching both ends of the new connecting rod. Make sure that the new connecting rod is secured and locked in place. See Diagram 2. For changing connecting rod, make sure there is no damage to the actual blade or arm that holds the connecting rod in place. If there is you must replace the entire blade system.2. Replacing Upper and Bottom Propeller: The propeller is subject to damage as you learn to properly fly and control your Air Combat. If after a crash your helicopter has loss of control or flies erratically you should carefully inspect your entire propeller system for any sign of damage. Most common are: cracked or chipped blade, broken “connecting rod”, frozen balance bar (this is when the balancing bar and blade are jammed and can not move freely up and down). To replace the propeller blades follow diagrams 3 through 12.7 8Diagram3Diagram4REPLACING THE UPPER PROPELLER BLADEDiagram5Diagram6Upper BladeDiagram7Diagram8Diagram9REPLACING THE BOTTOM PROPELLER BLADEDiagram10Diagram11When you tighten the screw you should test the blade to make sure that it still has free movement. If the blade cannot move freely, slightly loosen the screw.Bottom BladeDiagram12Please note the design of the bottom blade.Please note the design of the upper blade.Using a screwdriver turn counter clockwise to remove the screw. Using the screwdriver turn clockwise to tighten the screw.Using a screwdriver turn counter clockwise to remove the screw. Remove the broken blade and carefully replace with a new one.Remove the broken blade and carefully replace with a new one.Using the screwdriver turn clockwise to tighten the screw.When you tighten the screw you should test the blade to make sure that it still has free movement. If the blade cannot move freely, slightly loosen the screw.Diagram 1Replacing Connecting Rods There is one propeller connecting rod on the upper propeller.Diagram 2Proper connectionReplacing connecting rodBroken connecting rod Broken connecting rodPART REPLACEMENT INSTRUCTIONS
BATTERY WARNINGSRECHARGEABLE BATTERY:This helicopter uses an internal Li-Poly rechargeable battery and is not replaceable. If battery no longer stays charged, dispose of battery properly according to local disposal requirements.CONTROLLER BATTERIES:Remote control requires 6 “AA” batteries (not included). Please read the important battery safety warning below.• Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride).• Do not mix old and new batteries.• Non-rechargeable batteries are not to be recharged.• Rechargeable batteries are to be removed from the item before being charged (if removable).• Rechargeable batteries are only to be charged under adult supervision.• Exhausted batteries should be removed immediately and must be recycled or disposed of properly according to state or local government ordinances and regulations.• The supply terminals are not to be short-circuited.• Only batteries of the same or equivalent type as recommended are to be used.• Batteries are to be inserted with the correct polarity (see inside booklet for diagram).• Do not dispose batteries in a fire - batteries may leak or explode.CARE AND MAINTENANCE• Always remove the batteries from the wireless infrared remote control when it is not being used for an extended     period of time.• To clean, gently wipe the remote control and helicopter with a clean damp cloth.• Keep the toy away from direct heat or sunlight.• Do not submerge the toy into water. This can damage the unit beyond repair.• Parental guidance recommended when installing or replacing the batteries.FCC Part 15 B NoticeCAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•   Reorient or relocate the receiving antenna.•   Increase the separation between the equipment and receiver.•   Connect the equipment into an outlet on a circuit different     from that to which the receiver is connected.•   Consult the dealer or experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.109

Navigation menu