Aruba Networks APIN0224225 Wireless Access Point User Manual AP 22X Installation Guide Rev 01

Aruba Networks, Inc. Wireless Access Point AP 22X Installation Guide Rev 01

Manual

AP-220 Series Wireless Access PointInstallation GuideThe Aruba AP-224 and AP-225 wireless access points support the IEEE 802.11ac standard for high-performance WLAN. This access point uses MIMO (Multiple-in, Multiple-out) technology and other high-throughput mode techniques to deliver high-performance, 802.11n 2.4 GHz and 802.11ac 5 GHz functionality while simultaneously supporting existing legacy wireless services. The AP-220 Series access point works only in conjunction with an Aruba Controller.The Aruba AP-220 Series access point provides the following capabilities:Wireless transceiverProtocol-independent networking functionalityIEEE 802.11a/b/g/n/ac operation as a wireless access pointIEEE 802.11a/b/g/n/ac operation as a wireless air monitorCompatibility with IEEE 802.3at PoE+ and 802.3af PoE Central management configuration and upgrades with an Aruba ControllerPackage ContentsAP-224 or AP-225 access point 9/16" and 15/16” Ceiling Rail AdaptersInstallation guide (this document)AP-220 Series Hardware OverviewFigure 1 LEDsLEDsThe AP-220 Series is equipped with five LEDs that indicate the status of the various components of the AP.External Antenna ConnectorsThe AP-224 is equipped with three external antenna connectors. The connectors are labeled ANT0, ANT1, and ANT2, and correspond to radio chains 0, 1, and 2. Figure 2 External Antenna Connectors (AP-224 only) Figure 3 Bottom Panel USB InterfaceThe AP-220 Series is equipped with a USB interface for connectivity with cellular modems. Console PortThe serial console port allows you to connect the AP to a serial terminal or a laptop for direct local management. This port is an RJ-45 female connector with the pinouts described in Figure 4. Connect it directly to a terminal or terminal server using an Ethernet cable.Figure 4 Serial Port Pin-OutEthernet PortsAP-220 Series is equipped with two10/100/1000Base-T (RJ-45) auto-sensing, MDI/MDX wired-network connectivity port. These ports support IEEE 802.3af and 802.3at Power over Ethernet (PoE) compliance, accepting 56VDC as a standard defined Powered Device (PD) from a Power Sourcing Equipment (PSE) such as a PoE midspan injector, or network infrastructure that supports PoE.The 10/100/1000 Mbps Ethernet ports are on the bottom of the AP. These ports have RJ-45 female connectors with the pin-outs shown in Figure 5. Figure 5 Gigabit Ethernet Port Pin-OutKensington Lock SlotThe AP-220 Series is equipped with a Kensington security slot for additional security. Reset ButtonThe reset button can be used to return the AP to factory default settings. To reset the AP:1. Power off the AP.2. Press and hold the reset button using a small, narrow object, such as a paperclip.3. Power-on the AP without releasing the reset button. The power LED will flash within 5 seconds.4. Release the reset button.The power LED will flash again within 15 seconds indicating that the reset is completed. The AP will now continue to boot with the factory default settings.DC Power SocketIf PoE is not available, an optional Aruba AP AC-DC adapter kit (sold separately) can be used to power the AP-220 Series. Additionally, a locally-sourced AC-to-DC adapter (or any DC source) can be used to power this device, as long as it complies with all applicable local regulatory requirements and the DC interface meets the following specifications:12 VDC (+/- 5%)/18WCenter-positive 1.7/4.0 mm circular plug, 9.5 mm lengthBefore You BeginPre-Installation Network RequirementsAfter WLAN planning is complete and the appropriate products and their placement have been determined, the Aruba controller(s) must be installed and initial setup performed before the Aruba APs are deployed.For initial setup of the controller, refer to the ArubaOS Quick Start Guide for the software version installed on your controller.AP Pre-Installation ChecklistBefore installing your AP-220 Series AP, ensure that you have the following:CAT5e or CAT6 UTP cable of required lengthOne of the following power sources:IEEE 802.3at or 802.3af-compliant Power over Ethernet (PoE) source. The POE source can be any power source equipment (PSE) controller or midspan PSE deviceAruba AP AC-DC adapter kit (sold separately)Aruba Controller provisioned on the network:Layer 2/3 network connectivity to your access pointOne of the following network services:Aruba Discovery Protocol (ADP)DNS server with an “A” recordDHCP Server with vendor-specific optionsSummary of the Setup ProcessSuccessful setup of an AP-220 Series access point consists of five tasks, which must be performed in this order:1. Verify pre-installation connectivity.2. Identify the specific installation location for each AP.3. Install each AP.4. Verify post-installation connectivity.5. Configure each AP.Verifying Pre-Installation ConnectivityBefore you install APs in a network environment, make sure that the APs are able to locate and connect to the controller after power on.Specifically, you must verify the following conditions:When connected to the network, each AP is assigned a valid IP addressAPs are able to locate the controller Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller.Identifying Specific Installation LocationsYou can mount the AP-220 Series access point on a wall or on the ceiling. Use the AP placement map generated by Aruba’s RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/interference sources will impact RF propagation and should have been accounted for during the planning phase and adjusted for in RF plan.Identifying Known RF Absorbers/Reflectors/Interference SourcesIdentifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an AP to its fixed location. Examples of sources that degrade RF performance include:Cement and brickObjects that contain waterMetalMicrowave ovensWireless phones and headsetsThe AP-220 Series requires ArubaOS 6.3.0.0 or later.Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed.Table 1 AP-220 Series Series LED MeaningsLED Color/State MeaningPWR Off No power to APRed Initial power-up Green - Flashing AP bootingGreen - Steady AP readyENET0, ENET1 Off Ethernet link unavailableAmber - Steady 10/100Mbps Ethernet link establishedGreen - Steady 1000Mbps Ethernet link establishedFlashing Ethernet link activity5GHz Off 5GHz radio disabledAmber - Steady 5Ghz radio enabled in non-HT WLAN modeGreen - Steady 5Ghz radio enabled in HT WLAN modeFlashing - Green 5Ghz Air or Spectrum Monitor2.4GHz Off 2.4GHz radio disabledAmber - Steady 2.4Ghz radio enabled in non-HT WLAN modeGreen - Steady 2.4Ghz radio enabled in HT WLAN modeFlashing - Green 2.4Ghz Air or Spectrum Monitor2.4Ghz5GhzENET1ENET0PWRThe USB interface is disabled when the AP-220 Series is powered from 802.3af PoE.ANT0 ANT2ANT1Kensington LockUSB Interface Console Port Ethernet PortsDC Power SocketReset ButtonSerialConsole Port12345678TxDGNDRxDRJ-45 FemalePin-OutDirectionInputOutputGNDWhen operating on 802.3af, only the port connected to power is usable. For example, if the source of power is connected to ENET 0, ENET 1 will not work.!FCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).!EU Statement: Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide for details on restrictions.Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User Guide pour les details des restrictions.Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich Einschränkungen finden Sie im ArubaOS User Guide.Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide per avere informazioni detagliate sulle restrizioni.1000Base-T Gigabit Ethernet PortRJ-45 FemalePin-OutSignal Name12345678BI_DC+BI_DC-BI_DD+BI_DD-BI_DA+BI_DA-BI_DB+BI_DB-FunctionBi-directional pair +C, POE PositiveBi-directional pair -C, POE PositiveBi-directional pair +D, POE NegativeBi-directional pair -D, POE NegativeBi-directional pair +A, POE NegativeBi-directional pair -A, POE NegativeBi-directional pair +B, POE PositiveBi-directional pair -B, POE Positive Aruba Networks, Inc., in compliance with governmental requirements, has designed the AP-220 Series access points so that only authorized network administrators can change the settings. For more information about AP configuration, refer to the ArubaOS Quick Start Guide and ArubaOS User Guide.!Access points are radio transmission devices and as such are subject to governmental regulation. Network administrators responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in which the access point will be used.
AP-220 Series Wireless Access PointInstallation Guidewww.arubanetworks.com1344 Crossman AvenueSunnyvale, California 94089Phone: 408.227.4500Fax 408.227.4550AP-220 Series Wireless Access Point | Installation GuidePart Number 0511266-01 | February 2013Contacting Aruba NetworksTable 1 Web Site SupportMain Site http://www.arubanetworks.com Support Site https://support.arubanetworks.com Software Licensing Site https://licensing.arubanetworks.com/login.phpWireless Security IncidentResponse Team (WSIRT)http://www.arubanetworks.com/support/wsirt.phpAmericas and APAC Support Email support@arubanetworks.com EMEA Support Email emea.support@arubanetworks.comWSIRT EmailPlease email details of any securityproblem found in an Aruba product.wsirt@arubanetworks.comTable 2 Telephone SupportAruba Corporate +1 (408) 227-4500FAX +1 (408) 227-4550Copyright© 2013 Aruba Networks, Inc. AirWave®, Aruba Networks®, Aruba Mobility Management System®, Bluescanner, For Wireless That Works®, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtect®, The All Wireless Workplace Is Now Open For Business, and The Mobile Edge Company® are trademarks of Aruba Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners.Open Source CodeCertain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open Source Licenses. The Open Source code used can be found at this site:http://www.arubanetworks.com/open_sourceLegal NoticeThe use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those vendors.WarrantyThis hardware product is protected by the standard Aruba warranty of one year parts/labor. For more information, refer to the ARUBACARE SERVICE AND SUPPORT TERMS AND CONDITIONS.Altering this device (such as painting it) voids the warranty.Installing the APUsing the Ceiling Rail AdapterThe AP-220 Series ships with two ceiling rail adapters for 9/16” and 15/16” ceiling rails. Additional wall mount adapters amd ceiling rail adapters for other rail styles are available as accessory kits.1. Pull the necessary cables through a prepared hole in the ceiling tile near where the AP will be placed.2. Place the adapter against the back of the AP with the adapter at an angle of approximately 30 degrees to the tabs (see Figure 6).3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 6).Figure 6 Attaching the Ceiling Rail Adapter4. If necessary, connect the console cable to the console port on the back of the AP.5. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots at approximately a 30-degree angle to the ceiling tile rail (see Figure 7). Make sure that any cable slack is above the ceiling tile.6. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks into place on the ceiling tile rail.Figure 7 Mounting the AP7. On the AP-224, install the external antennas according to the manufacturer’s instructions, and connect the antennas to the antenna interfaces on the AP.Connecting Required CablesInstall cables in accordance with all applicable local and national regulations and practices.Power ConnectionThe AP-220 Series has a single 12V DC power jack socket to support powering through an AC-to-DC power adapter.Verifying Post-Installation ConnectivityThe integrated LEDs on the AP can be used to verify that the AP is receiving power and initializing successfully (see Table 1). Refer to the ArubaOS Quick Start Guide for further details on verifying post-installation network connectivity.Configuring the AP-220 SeriesAP Provisioning/ReprovisioningProvisioning parameters are unique to each AP. These local AP parameters are initially configured on the controller which are then pushed out to the AP and stored on the AP itself. Aruba recommends that provisioning settings be configured via the ArubaOS Web UI only. Refer to the ArubaOS User Guide for complete details.AP ConfigurationConfiguration parameters are network or controller specific and are configured and stored on the controller. Network configuration settings are pushed out to the AP(s) but remain stored on the controller.Configuration settings can be configured via the ArubaOS Web UI, ArubaOS CLI, or Aruba MMS. Refer to their respective guides for further details: the ArubaOS User Guide or Aruba Mobility Management System User Guide.Product SpecificationsElectricalEthernet:2 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 InterfacesMDI/MDXIEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)Power over Ethernet (IEEE 802.3at compliant), 48V DC/350mA (see Figure 5 for pin configuration))Power:12 VDC power interface, supports powering through an AC-to-DC power adapterPOE support on Ethernet ports: 802.3at-compliant POE sourcing devicesFor additional specifications on this product, please refer to the data sheet. The data sheet can be found at www.arubanetworks.com.Proper Disposal of Aruba EquipmentFor the most current information about Global Environmental Compliance and Aruba products, see our website at www.arubanetworks.com.Waste of Electrical and Electronic EquipmentAruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE).China RoHSAruba products also comply with China environmental declaration requirements and are labeled with the “EFUP 10” label shown at the left.European Union RoHSAruba products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this Directive.Safety and Regulatory ComplianceAruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded from the following location: www.arubanetworks.com/safety_addendum Regulatory Model NamesThe following regulatory model names apply to the AP-220 Series:AP-224: APIN0224AP-225: APIN0225FCCThe device is electronically labeled and the FCC ID will be displayed via the controller WebUI under the About menu. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Class B Part 15This device complies with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions:This device may not cause harmful interference.This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause interference harmful to radio communications.If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio or TV technician for help.Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada.EU Regulatory ConformanceThis product is CE marked according to the provisions of the R & TTE Directive (99/5/EC) - CE 2280(!){! In circle}. Aruba Networks Inc., hereby declares that this AP-224 and AP-225 device models are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. CE 2280(!)The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at the following location in the EU community.Service to all Aruba Networks products should be performed by trained service personnel only.!Make sure the AP fits securely on the ceiling tile rail when hanging the device from the ceiling, because poor installation could cause it to fall onto people or equipment.If both POE and DC power are available, the AP draws power from the PoE source.AP-220_04AP-220_005If a power adapter other than the one provided by Aruba Networks is used in the US or Canada, it should be cULus (NRTL) Listed, with an output rated 12 VDC, minimum 1.25A, marked “LPS” or “Class 2,” and suitable for plugging into a standard power receptacle in the US and Canada.10!RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.9 inches (20 cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems.!Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Navigation menu