Aroot LK-P41B Mobile Printer User Manual

SEWOO TECH CO., LTD. Mobile Printer

User manual

All specifications are subject to change without notice02%,/(35,17(5MODEL : LK-P41B
23Table of Contents1. Product overview 32. Unpacking 3. Usage and Installation 53-1. Control panel usage53-2. Battery Installation63-3. Battery charging73-4. Battery charger usage83-5. Roll paper installation93-6. Leather case usage103-7. Self test114. Peripherals connection 134-1. Bluetooth connectiontion134-2. Interface cable connection145. Printer specification 155-1. Specification156. CPCL Command Compatibility 177. Setting up the software 201. Unpacking StandardOptionPrinter BatterySerial CableRoll paperUSB Cable ShieldedChargerCD Quick ManualBattery Holder (Cradle) Leather case Shoulder strip
45ButtonNamefunctionPower buttonThis button is used to turn the printer on and off.When the printer is off, press this button for approximately 3 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off.Paper Feed ButtonPaper output can be done manually by pressing this button.Additionally, self-testing and Hexadecimal Dumping can be processed..1. Refer to “3-10” for self test information.2. Refer to the service manual regarding Hexadecimal Dumping.Battery Status Lamp1. If the Batt, LED are Lit, the battery is fully charged.2. If you can hear beeping sound and LED light is turned off, it means that the battery is at the lowest level.3. If the battery is not charged at all, the printer turns off automatically.Error Lamp If the red light is turned on, it means there is no paper roll or the paper cover is open. 2. Product overview 3. Usage and Installation3-1 Control panel usagePaper feed buttonPower switch DC PowerBatterySERIALUSBOpen Button
671. Align battery hook as shown in the picture2. Push the battery into the printer until it locks in place.NOTEAs the battery is not charged at the time of your purchase, charge the battery prior to using the printer(Battery charger or Cradle can be used to charge) ⷍCAUTIONRisk of explosion if battery is replaced by an incorrect type.Dispose of used batteries according to the instructionsHook3-2 Battery InstallationNOTE1. Unless the exclusive charger is used provided by the manufacturer, the printer can be damaged, and the manufacturer is not liable for the consequential damage.2. Before removing the battery, make sure that power is turned off.3. Printer does not work in the status of being connected with charger only.4. The battery should be installed to operate printer.5. While charging, do not turn on the power.6. Do not operate the print while charging the battery.7. Do not connect the charger while the printer is operated.1. Be sure that the printer is turned off 2. After open the DC JACK cover, insert DC JACK into the printer.3. Plug the power code to electrical outlet.3-3 Battery charging
893-5-1 The status of lamp in charginglampStatus charging charging complete Charging Lamp Red GreenNOTEIn the case the battery is not fixed properly in the holder, the red lamp will be blinking, Then, extract and reinsert the battery.3-4 Battery charger usageDC Jack1. Insert the battery into the battery holder as shown above2. Connect the DC JACK to the power electrical outlet.3. Plug the power code into the electrical outlet.4. Once the charging is completed, remove the battery from the holder.Optional1234Press the PUSH button to open the paper coverPull a short length of paper out of the printer and close the cover.Insert the paper in the right directionTear off the additional paper using tear bar.3-5 Roll Paper installation
10 1112 3Open the leather caseClose the Velcro and stick the cover.Place the printer into the leather case3-6 Leather case usageOptional123NOTETurn off the power pressing the power button for approximately 3 seconds.The printout is produced.While you are pressing the FEED button, press the power button3-7 Self Test1. To print ASCII pattern additionally, press the Feed button once more2. After printing ASCII pattern, the self test will be finished automatically.3. If the Feed button is not pressed to print ASCII pattern, self test will be finished automatically after 30 seconds.
12 13When the printer is installed initially or when you face a problem, you can run the self test and check the information about-Control Circuit, Mechanism, Print Quality, ROM VersionAfter checking with self-test and no issues are found, you can examine other devices and software. This function is working independent of devices and software. <The sample of self test printout>مMotor protection from being overheated The motor should be stopped and cooled about more than 30 seconds after continuous printing 1.5 meter1. Printer can be connected to the PDA and PC which can do wireless communication.2. By using Bluetooth function supported in PC, printer can be connected.This printer can communicate with Peripherals device via Bluetooth and cables.4-1 Bluetooth Connection4. Peripherals connection
14 154-2 Interface Cable Connection1. Connect USB or Serial cable into the cable connector on the printer.2. Connect the interface cable into the USB or Serial port of the device (PDA, PC, etc.)NOTEUse the cable offered by the manufacturer (USB, Serial)SerialUSBPrinting Method Direct ThermalPrinting Speed 80mm/secResolution 203 DPI X 203 DPICharacter CPCL 7 Different Font Size (12~48pt)ESC/POS Font A (12X24), Font B (9X17)Character per line Font A : 48pt, Font B : 64ptCharacter set ALPHA NUMERIC Character, Extension CharacterBarcode EAN-8, EAN-13, Code39, ITF, UPC-A, UPC-E,Codabar, Code93, Code128, PDF417(2D),MAXICode (2D)Emulation ESC/POS, CPCL, Commanl CompatibleDriver Window CE 4.2&5.0, Window Mobile 5.0Sensor Paper End Sensor , Gap Sensor , Cover Open Sensor , Black Mark SensorPaper paper type Thermal Paper / Labelwidth 25.4mm ~112mmthickness 0.06mm ~ 0.09mmExternal Diameter Max. ⱒ56mmInternal Diameter 12.5mm +/-0.5mmReliability TPH 50kmBattery Continuous printing operation: 1hr and 30minStandby: 24hrsPrinting length: 162mCommunications Serial(RS-232C), USB, Bluetooth Class2Battery Charger input AC100~240V, 50/60 Hz5. Pritner Specification 5-1 Specification
16 17Battery Charger Battery type Li-ionoutput 7.4V, 2200mAhCharging time 3 hour 40 minuteSize W X D X H(mm) 149 X 161 X 69W X D X H” 5.8 X 6.3 X 2.7Weight 0.53kg (With Battery)Temperature operation -10 ~ 50Ⳅstorage -20 ~ 60ⳄHumidity operation 35 ~ 95%Printer Commands CompatibilityPRINTⷃFORMⷃJOURNALⷃUNITSⷃCommentsⷃTEXT CompatibilityTEXTⷃFONT-GROUP(FG)ⷃTEXT CONCATENATIONⷃMULTILINE(ML)ⷃCOUNTⷃSETMAGⷃSCALABLE TEXT9Linear Bar Codes CompatibilityBARCODEⷃBARCODE-TEXTⷃTwo-Dimensional Bar Codes CompatibilityPDF417 (PORTABLE DATA FILE)ⷃMAXICODEⷃQRCODEⷅDATAMATRIXⷅGS1(RSS)ⷅ/05&Compatible Partially CompatibleNotCompatibleⷃⷅⶹYCompatible with only commanders provided by the manufacturer.6. CPCL Command Compatibility
18 19Graphics CompatibilityBOXⷃLINEⷃINVERSE-LINEⷃPATTERNⷃGRAPHICSⷃPCXⷃAdvanced Commands CompatibilityCONTRASTⷃTONEⷃJUSTIFICATIONⷃPAGE-WIDTHⷃPACEⷃNO-PACEⷃWAITⷃREWIND9TENSION9SPEEDⷃSETSPⷃON-OUT-OF-PAPER 9ON-FEEDⷃPREFEEDⷃPOSTFEEDⷃPRESENT-AT9COUNTRY/CODE PAGEⷃFORMAT FILESⷃBEEPⷃCUT9PATIAL-CUT9MCRⷅLine Print Mode CompatibilitySETLPⷃSETLFⷃMoving With X and Y CoordinatesⷃLMARGINⷃSETBOLDⷃSETSPⷃSpecial ASCII CharactersⷃSETFFⷃSET-TOFⷃSETLP-TIMEOUTⷃ
20 21Please refer to the programming manual included in CD. FCC InformationThis device complies with part 15 of the FCC Results. Operation is subject to the following two conditions: (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation.NoteThis equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instuctions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. WARNINGChanges or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.ǁCertification7. Setting up the softwareCAUTIONAntenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit.
Rev. 1.0SEWOO TECH CO.,LTD.ADDRESS Doosung Bd, 689-20, Kumjung-dong, Kunpo-si, Kyunggi-do, KoreaTEL 82-31-459-8200 FAX 82-31-459-8880URL http://www.miniprinter.com

Navigation menu