Aroot LK-P31 Mobile Printer User Manual manual

SEWOO TECH CO., LTD. Mobile Printer manual

manual

Rev. 1.0SEWOO TECH CO.,LTD.Doosung BD, 689-20, Geumjung-dong, Gunpo-si, Gyeonggi-do, 435-862 South KoreaTEL : +82-31-459-8200 FAX : +82-31-459-8880www.miniprinter.comAll specifications are subject to change without noticeMOBILE PRINTERMODEL : LK-P31
1 Table of Contents 1. Unpacking 2 2. Product overview 3 3. Usage and Installation 4 3-1. Control panel usage4 3-2. Battery Installation5 3-3. Battery removal6 3-4. Battery charging7 3-5. Battery charger usage8 3-7. Roll paper installation9 38. Self test10 4. Peripherals connection 12 4-1. Bluetooth connectiontion12 4-2. Interface cable connection13 5. Printer specification 14 5-1. Specification14 6. Certification 16
232. Product overview Paper feed buttonOpen ButtonPower switch ControlPanel BatteryUSB FrontRear1. Unpacking PrinterBatteryRoll paperUSB Cable ShieldedChargerCD Quick ManualBattery Holder (Cradle) Shoulder stripOptionalStandard
451. Align battery hook as shown in the picture2. Push the battery into the printer until it locks in place.NOTEAs the battery is not charged at the time of your purchase, charge the battery prior to using the printer(Battery charger or Cradle can be used to charge) Hook 3-2 Battery Installation☞CAUTIONRisk of explosion if battery is replaced by an incorrect type.Dispose of used batteries according to the instructions3. Usage and Installation3-1 Control panel usage Button Name functionPower buttonThis button is used to turn the printer on and off.When the printer is off, press this button for approximately 3 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off.Paper Feed ButtonPaper output can be done manually by pressing this button.Additionally, self-testing and Hexadecimal Dumping can be processed..1. Refer to “3-10” for self test information.2. Refer to the service manual regarding Hexadecimal Dumping.Battery Status Lamp1. If the Batt, LED are Lit, the battery is fully charged.2. If you can hear beeping sound and LED light is turned off, it means that the battery is at the lowest level.3. If the battery is not charged at all, the printer turns off automatically.Error Lamp If the red light is turned on, it means there is no paper roll or the paper cover is open.
67NOTE1. Unless the exclusive charger is used provided by the manufacturer, the printer can be damaged, and the manufacturer is not liable for the consequential damage.2. Before removing the battery, make sure that power is turned off.3. Printer does not work in the status of being connected with charger only.4. The battery should be installed to operate printer.5. While charging, do not turn on the power.6. Do not operate the print while charging the battery.7. Do not connect the charger while the printer is operated.1. Be sure that the printer is turned off 2. After open the DC JACK cover, insert DC JACK into the printer.3. Plug the power code to electrical outlet.3-4 Battery chargingAfter putting up the belt clip, remove the battery holding it up as shown above.3-3 Battery removalLamp3-4-1 The status of lamp in chargingStatus charging charging complete Charging Lamp Red Green
893-5-1 The status of lamp in chargingStatus charging charging complete Charging Lamp Red GreenNOTEIn the case the battery is not fixed properly in the holder, the red lamp will be blinking, Then, extract and reinsert the battery.1. Insert the battery into the battery holder as shown above2. Connect the DC JACK to the power electrical outlet.3. Plug the power code into the electrical outlet.4. Once the charging is completed, remove the battery from the holder.3-5 Battery charger usageOptionalLamp DC Jack1 234Press the PUSH button to open the paper coverPull a short length of paper out of the printer and close the cover.Insert the paper in the right directionTear off the additional paper using tear bar.3-6 Roll paper installation
10 111 23NOTETurn off the power pressing the power button for approximately 3 seconds.The printout is produced.While you are pressing the FEED button, press the power button3-7 Self Test1. To print ASCII pattern additionally, press the Feed button once more2. After printing ASCII pattern, the self test will be finished automatically.3. If the Feed button is not pressed to print ASCII pattern, self test will be finished automatically after 30 seconds.When the printer is installed initially or when you face a problem, you can run the self test and check the information about-Control Circuit, Mechanism, Print Quality, ROM VersionAfter checking with self-test and no issues are found, you can examine other devices and software. This function is working independent of devices and software. ● Motor protection from being overheated The motor should be stopped and cooled about more than 30 seconds after continuous printing 1.5 meterThe sample of self test printout
12 131. Printer can be connected to the PDA and PC which can do wireless communication.2. By using Bluetooth function supported in PC, printer can be connected.This printer can communicate with Peripherals device via Bluetooth and cables.4-1 Bluetooth Connection4. Peripherals connectionNOTERefer to the Bluetooth Manual for more details on connection.4-2 Interface Cable Connection1. Connect USB into the cable connector on the printer.2. Connect the interface cable into the USB port of the device (PDA, PC, etc.)NOTEUse the cable offered by the manufacturer (USB)USB
14 15Printing Method Direct ThermalPrinting Speed 60mm/secResolution 203 DPI X 203 DPICharacter Font A (12X24), Font B (9X17)Character per line Font A : 48pt , Font B : 64ptCharacter set ALPHA NUMERIC Character, Extension CharacterBarcode EAN-8, EAN-13, Code39, ITF, UPC-A,Codabar, Code93, Code128Emulation ESC/POSDriver Window CE 4.2&5.0, Window Mobile 5.0Sensor Paper End Sensor , Cover Open Sensor , Black Mark SensorPaper paper type Thermal Paper / Labelwidth 80mmthickness 0.065mmExternal Diameter Max. Φ25mm+/-0.5mmInternal Diameter 8.5mm +/-0.5mmReliability TPH 50kmBattery Continuous Printing 40~50minStandby: 11hourCommunications USB, Bluetooth Class2Battery Charger input AC100~240V, 50/60Hzoutput 8.4V , 800~1400mABattery Battery type Li-ionoutput 7.4V, 1130mAhCharging time 2~3hours5. Pritner Specification 5-1 SpecificationSize W X D X H(mm) 110 X 105 X 30W X D X H” 4.3 X 4.1 X 1.2Weight 310gEnvironmental sealing IP42Temperature operation -10 ~ 50℃storage -20 ~ 60℃Humidity operation 35 ~ 95%storage 10 ~ 95%BT Frequency 2402 ~2480 MHzNumber of Channels 79Channel Spacing 1 MHzType of Modulation GFSK (1Mbps)
16 176. CertificationFCC Inform ationThis device complies with part 15 of the FCC Results. Operation is subject to the following two conditions: (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instuctions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.NOTEWARNINGOperation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.This Class [B] digital apparatus complies with Canadian ICES-003.Cet appareil numerique de la classe [B] est conforme a la norme NMB-003 du Canada.

Navigation menu