Argox Information Co PI-1X60 Data Collector User Manual PI 1060 UserMan 20181005

Argox Information Co Ltd Data Collector PI 1060 UserMan 20181005

UserManual.wiki >

Argox Information Co >

PI 1X60 User Manual

PI-1060- UserMan-20181005

PI‐1000SeriesPortabledataterminalUser’sManualPI‐1010/PI‐1030/PI‐1060/PI‐1230 http://www.argox.comservice@argox.com V1.205‐06‐2018

iRegulatoryComplianceFEDERALCOMMUNICATIONSCOMMISSIONINTERFERENCESTATEMENTThis equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to part 15 of theFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainst harmful interference in a residential installation. Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,may cause harmful interference to radio communications.However,thereisnoguaranteethatinterferencewillnotoccurina particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can bedetermined by turning the equipment off and on, the user isencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:‐Reorientorrelocatethereceivingantenna.‐Increasetheseparationbetweentheequipmentandreceiver.‐Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.‐Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

iiCAUTION:Anychangesormodificationsnotexpresslyapprovedbythegranteeofthisdevicecouldvoidtheuser'sauthoritytooperatetheequipment. PI-1010 EN 300 328 BT RF Power EIRP 1.92 dbm PI-1060 EN 300 328 BT RF Power EIRP 1.92 dbm PI-1060 EN 300 200 SUB-1G RF Power EIRP 5.17 dbm PI-1030 EN 300 328 BT RF Power EIRP 1.92 dbm PI-1030 EN 300 328 WIFI RF Power EIRP 19.04 dbm PI-1230 EN 300 328 BT RF Power EIRP 1.92 dbm PI-1230 EN 300 328 WIFI RF Power EIRP 19.04 dbmRFexposurewarning  TheequipmentcomplieswithFCCRFexposurelimitssetforthforanuncontrolledenvironment.Theequipmentmustnotbeco‐locatedoroperatinginconjunctionwithanyotherantennaortransmitter.

iiiRadioTransmitters(Part15)ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceivedincludinginterferencethatmaycauseundesiredoperation.FCCID:NBF‐PI‐1X30ForPI‐1010&PI‐1030&PI‐1230FCCID:NBF‐PI‐1X60ForPI‐1060Note:PI‐1060OnlyBT&Sub‐1GRFFunctionCAUTION:EXPLOSIONHAZARDDo not disassemble, short circuit, heat the battery or dispose of in fire. Store battery packinaproperplace.Donotexposetotemperatureabove60℃/140℉.Usespecifiedchargeronly.Pleasedisposeoftheusedbatteriesfollowingtherulesorlawsissuedbythelocalgovernment.

iv警告：電池若未妥善處理，可能會導致爆炸。請勿拆卸電池，或用火銷毀電池。請將電池放置於兒童拿不到的地方。請使用專用充電器充電，並請依照當地政府或法律規定妥善處理廢棄電池。低功率電波無線輻射電機管理辦法第十二條：經型式認證合格之低功率射頻電機, 非經許可,公司, 商號或使用者均不得擅自變更頻率,加大功率或變更原設計之特性及功能。第十四條：低功率射頻電機之使用不得影響飛航影響安全及干擾合法通信, 經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前項合法通信,指一電信法規定作業之無線電通信低功率射頻電機需忍受合法通信或工業,科學及醫療用電波輻射性電機設備之干擾 本產品支援 WIFI/Bluetooth/Sub-1G(依不同型號有所不同) 製造商：立象科技股份有限公司地址：新北市新店區寶橋路 235 巷126 號7樓電話：02‐8912‐1121（代表號）

v

ReleaseNoteiRelease Note Version Date Note V1.0 02/22 2017 Initial release V1.1 07/12 2017 Add Appendix A for reference V1.1 02/13 2018 Add Appendix B for reference V1.2 06/05 2018 Add PI-1060, Tag-60 information

iiContent1 Introduction..........................................................................11.1 Unpacking.................................................................21.2 Understandyourterminal........................................41.2.1 Terminal........................................................41.2.2 Holder(Option)..............................................51.3 Indicators..................................................................61.3.1 LED................................................................61.3.2 Buzzer............................................................81.3.3 Vibration.......................................................81.4 Keypad......................................................................91.5 Powersource..........................................................151.6 Tag‐60introduction(PI‐1060only).........................162 Getstarted..........................................................................172.1 Setupyourterminal...............................................212.2 Userinterface.........................................................232.3 Connection.............................................................252.3.1 Remotelinkconnection..............................262.4 Attachthehandstrap.............................................302.5 Tag‐60(PI‐1060)......................................................323 Controlsandsettings..........................................................353.1 UserMenu..............................................................353.1.1 RunProgram...............................................363.1.2 RemoteLink................................................363.1.3 Scanner(HID)...............................................37

iii3.1.4 Information.................................................383.2 SystemMenu..........................................................393.2.1 RemoteLink................................................393.2.2 Diskinfo......................................................393.2.3 Timersetting...............................................403.2.4 Environment...............................................413.2.5 Test..............................................................423.2.6 Systeminfo..................................................443.3 SupervisorMenu....................................................453.3.1 RemoteLink................................................463.3.2 Formatdisk.................................................493.3.3 Setting.........................................................503.3.4 Information.................................................554 Applications........................................................................565 Troubleshooting..................................................................575.1 Hardwareissues......................................................575.2 Communicationissues............................................585.3 Barcodescanningissues.........................................596 Specifications......................................................................60AppendixA..............................................................................66AppendixB..............................................................................83

1Introduction Unpacking11 IntroductionPIseriesisalightweight,portabledataterminal(PDT)fordatacaptureandcollection.ThismanualwillhelpyoutogettoknowPIseriesandutilizeitwell.Features￭ Scratch‐resistantkeypadCoatedwithPC(polycarbonate),thelettersandnumbersonthekeyswon’twearoffbetweenuses.￭ Batterycoveropendetection  Whentheswitchofthebatterycoverisup,thesystemautomaticallysavesyourfilesandshutdown.￭ Largeflashmemory  PIseriesoffersmoreflashmemorythantherivalsonthesamelevel.Thestandardis20MB,andtheoptionalis60MB.￭ Backupbattery  Thebackupbatterygivesyouadditional15minutestofinishyourjobiftheprimarybatterieswearout.￭ Wi‐Ficonnectivity  YoucanexchangedataoveraWi‐Finetwork.(PI‐1030)￭ Tag‐60 

1Introduction Unpacking21.1 UnpackingMakesureallofthefollowingitemsareincludedinyourpackage.PIseries QuickStartGuideUSBCable or RS‐232CablewithUSBpowercordHolder HandStrap

1Introduction Unpacking3PlugandPowerSupply(Option)Tag‐60(PI‐1060) Whenyoureceiveyourterminal,openthepackageimmediatelyandinspectforshippingdamage.Ifyoudiscoveranydamage,contacttheshippingcompanyandfileaclaim.Argoxisnotresponsibleforanydamageincurredduringshipping.Saveallpackagematerialsfortheshippingcompanytoinspect.Note  Ifanyitemismissing,pleasecontactyourlocaldealer.

1Introduction Understandyourterminal41.2 Understandyourterminal1.2.1 TerminalLeft Front Right BackTop Bottom1 LED ThreeLEDs.2 LCDDisplay AmonoLCD.3 Keypad A25‐keykeypad.4 BatteryCover Thebatterycover.5 BatteryCoverSwitch Openandclosethebatterycover.6 ReadingWindow Thebarcodereadingbeamisemittedthroughthiswindow.7 Speaker Buzzersound12368547

1Introduction Understandyourterminal58 Connector Aporttoconnectcomputer1.2.2 HolderTheholderisusedtoholdyourterminalinitsstandingposition.Inthebottomofholder,makesurecablewireisinstalledasbelow. 

1Introduction Indicators61.3 IndicatorsPIserieshasthreeLEDsandabuzzertoindicateitscurrentstatus. 1.3.1 LEDYourterminalhasthreeLEDsontheupper‐leftcorner.Theyhavedifferentbehavior.Thetablebelowgivesinformationaboutthestatustheyindicate.LED ColorScanLED Green,RedandOrangeBTorWi‐FiLED BlueChargerLED RedBTorWi‐FiLEDChargerLEDScanLED

1Introduction Indicators7LED Behavior Status NoteScanLEDSolidgreen Userdefined UseSDK.Solidred Userdefined. UseSDK.Solidorange Userdefined. UseSDK.FlashinggreenTransmittingdataoruserdefined.UseSDK.Flashingred Userdefined. UseSDK.FlashingorangeUserdefined. UseSDK.Off Nodatatransmissionoruserdefined.UseSDK.BT&Wi‐FiLEDSolidblue YourterminalisconnectedthroughBluetoothorWi‐Fi.FlashingblueYourterminalisreadytobeconnectedthroughBluetoothorWi‐Fi.Off BluetoothorWi‐Fiisturnedoff.DefaultChargerLEDSolidred Yourterminalisfullychargedorconnectedtoapowersource.Controlledbyhardware.Flashingred Charging. Controlledby

1Introduction Indicators8LED Behavior Status Notehardware.Off Yourterminalisnotconnectedtoanypowersource.Controlledbyhardware.1.3.2 BuzzerYoucandefinethestatusthevibrationindicatesusingtheSDK.Sound Status1ShortBeep Akeyispressed.Agoodscan.Anerroroccurred.2ShortBeep Thebatteryislow.4ShortBeep Batteryistoolowtoturnoffterminal.1.3.3 VibrationYoucandefinethestatusthevibrationindicatesusingtheSDK.Vibration StatusVibrate Agoodscan.

1Introduction Keypad91.4 KeypadScankeyCursorkeysControlkeysNumerickeysUser‐definedkeysPowerkeyScankeyScanabarcode.CursorkeysUp Movethehighlightbarup.Fn+Up OpenMessageMenu.Down Movethehighlightbardown.Fn+Down Adjustthebacklightbrightness.Thebrightnessrepeatsthesequence0123.Left Movethehighlightbartothetop.Fn+Left Reducethevolume.Right Movethehighlightbartothebottom

1Introduction Keypad10CursorkeysFn+Right Increasethevolume.ControlkeysESC TheEscapekey.1. Gouponelevelinamenu.2. Giveupchangingasetting.3. Exitaprogram.Fn TheFunctionkey.Usewithotherkeys.Ex:“Fn+DownArrow”istoadjustthebacklightbrightness.ThefunctionofF0‐F9(Fn+0‐9)canbedefinedusinganSDK.ENT TheEnterkey. 1. Enteramenu.2. Selectanoption.BS TheBackspacekey.1. Deleteacharactertotheleftofthecursor.NumerickeysYoucanusethekeypadtoenternumbersorEnglishcharacters,dependingonthemodeyou’reusing.1 1. Enterthenumberone.2. Enterthesesigns:plus(+),minus(‐),star(*)andslash(/).2 1. Enterthenumbertwo.2. EnterthelettersA,B,C.

1Introduction Keypad11Numerickeys3 1. Enterthenumberthree.2. EnterthelettersD,E,F.4 1. Enterthenumberfour.2. EnterthelettersG,H,I.5 1. Enterthenumberfive.2. EnterthelettersJ,K,L.6 1. Enterthenumbersix.2. EnterthelettersM,N,O.7 1. Enterthenumberseven.2. EnterthelettersP,Q,R,S.8 1. Enterthenumbereight.2. EnterthelettersT,U,V.9 1. Enterthenumbernine.2. EnterthelettersW,X,Y,Z.0 1. Enterthenumberzero.2. Enterthesecharacters:space(),at(@),comma(,)andsemicolon(;).Alpha Switchtheinputmethodbetweennumbers,uppercaseandlowercasecharacters.. 1. Enteraperiod(.).2. Enterthesesymbols:dollarsign($),percentsign(%),ampersand(&)andnumbersign(#).

1Introduction Keypad12User‐definedkeysP1 User‐definedkey.P2 User‐definedkey.P3 User‐definedkey.PowerkeyTurnonorturnoffyourterminal.PowercombinationkeyYoucanusethekeycombinationstoenterdifferentmenusormodes.Pressandholdthecombinationofkeys,untilyourterminalresponds.3+9+Power SystemMenu.1+3+0+Power SupervisorMenu.1+3+Power Forcemode.P1+P2+P3+Power BIOSreset.SCAN+Power Warmreset.SCAN+Power(5sec) Coldreset.Youneedtopressthekeysfor5seconds.

1Introduction Keypad13￭ SystemMenuEnterSystemMenu.￭ SupervisorMenu  EnterSupervisorMenu.￭ Forcemode  Itupdatesallfirmwarefilesandrestoresallsystemparameterstofactorysettings.ThismodeneedstobeusedwithanSDKorcomputersoftware.Youcanusethismodewhenyouencountertheproblemthatcan’tberesolvedinanyotherway.￭ BIOSreset  itisthesameasBIOSdefault(seeSupervisorMenu).Itresetsallyourterminalsettings,includingthepasswordofSupervisorMenu.￭ Warmreset  Itrestartsyourterminalwithoutchanginganysettings.Youcanuseitwhenyourprogramstopsresponding.￭ Coldreset  Itforcesyourterminaltorestart.ThedatastoredintheDRAMmayberemoved.Youcanuseitwhenyourterminalcrashes,orwhenyoucan’tturnonyourterminalbypressingthePowerkey.

1Introduction Keypad14

1Introduction Powersource151.5 PowersourceTherearethreewaystosupplypowertoPIseries:1. TwoAAbatteries.Recommendedalkalinerechargeabletype.2. UsetheUSBcablewithcomputer.3. UsethepowersupplywiththeUSBorRS‐232cable.CableType ChargeyourbatteriesSupplypowerwithoutbatteriesNeedtousewithapowersupplyUSB Yes Yes NoRS‐232 No No YesNote  It’snotnecessarytouseaUSBcablewiththepowersupply,butthebatterychargingtimeisshorterwithit.

1Introduction Tag‐60introduction(PI‐1060only)161.6 Tag‐60introduction(PI‐1060only)YoucandefineindicatorfunctionbyusingSDKorSkywalker.LEDColor StatusBlue Tag‐60iscalled.Red Tag‐60batterylowwarningSound StatusBeep BeepisdefinedbyPI‐1060application.RedLEDLatchBuzzerBatteryTAG‐60IDNo.BlueLEDTopstraphole

2Getstarted Tag‐60introduction(PI‐1060only)172 GetstartedThischapterprovidesinformationabouthowtoworkwithyourterminalandmakeconnectiontocomputer.Inserting or replacing battery Whenyouseethebatteryiconshowslow.Youneedtochangenewbatteryorchargeitimmediately.Ifthereisnopower,thebackupbatterycanholdthedataabout15minutes.Therefore,alwaysuploadyourimportantdataafterworkorkeeptwoAAbatteriesincase.Caution Donotmixoldbatteriesandnewbatteriesorstandard(carbon‐zinc)withalkalinebatteries.Removebatteriesifproductisnottobeusedwithforalongtime.Riskofexplosionifbatteryisreplacedbyanincorrecttype.Disposeofusedbatteriesaccordingtotheinstructions.DONOTRECHARGEDIFFERENTTYPESOFBATTERIES.

2Getstarted Tag‐60introduction(PI‐1060only)181. Pressandslidetworeleaselatchesatthesametimetoopenthebatterycover.2. Insertingtwobatteriesasindicatedinsidebatterycompartment.+‐‐+

2Getstarted Tag‐60introduction(PI‐1060only)193. Closethebatterycoverasfollow. 4. Makesurecoverisclosedandslidetwolatchesback.①②

2Getstarted Tag‐60introduction(PI‐1060only)20Charge the battery Ifyou’reusingrechargeablebatteriestosupplypowertoyourterminal,youcanchargethemby(1) connectingtheUSBcabletoyourterminalandcomputer.(2) Usingabatterychargertochargebatteriesinadvance.(3) ConnectingtheUSBcabletoyourterminalanduseapowersupply.Whenyourbatteriesarefullycharged,theChargerLEDturnstosolidred.Important  Toprotectpowersource,PIseriescannotbepoweredonunlessbatterycoverbackareclosedcorrectly. Chargingby FullChargeTimePowerSupply 5‐6hoursUSBCable 7‐8hoursImportant  BeforeusingPIseries,werecommendtochargePI‐1000series1daytomakesurebackupbatteryisfullycharged.

2Getstarted Setupyourterminal212.1 Setupyourterminal1. Chooseonetopoweronyourterminal OpenthebatterycoverandInstalltwoAANoteThetrianglemarkshouldbefaceupwhenyouwanttoconnecttoPIseries.

2Getstarted Setupyourterminal22batteries. ConnectyourterminaltoyourcomputerusingUSBorRS‐232cable.2. PressthePowerkeytoturnonyourterminal.Powerkey

2Getstarted Userinterface232.2 UserinterfaceItem DescriptionMenu CurrentmenutitleOptions Itemsinthemenu.Statusbar Itdisplaystheinformationaboutyourterminal.Inputmethod Thewayyouenterdata.Youcanenternumbers,lowercaseoruppercasecharacters.Time Thecurrenttime.MenuOptionsInputmethodTimePowersourceWireless Statusbar

2Getstarted Userinterface24Item DescriptionWirelesscommunicationWhenyouopenBluetoothorWi‐Fifunction,itdisplaysaniconwithoutwaves.Ifconnectionissuccessful,theiconwillshowwaves.Powersource Ifyourterminalisconnectedtoadirectpowersupply(USBorRS‐232),itdisplaysaplugicon;ifitisrunningonbatteries,itdisplaysabatteryicon.

2Getstarted Connection252.3 ConnectionPIserieshavefourinterfacestoconnect:USB,RS232,BluetoothandWI‐FI.Eachonecanchoosetwowaysasbelow.Remotelink:ItisauniqueprotocolfromArgoxdevelopment.VisitArgoxwebsitebelowtodownloadapplication.http://www.argox.com/content2011.php?sno=0000033Linkingport:Developercansetupdifferent interfacesUSB/WIFI/COM/BTaccordingtotheirapplication. Important RemotelinkhastouseArgoxapplication,suchasPhoenixVolerorEverlinkfromArgox.

2Getstarted Connection262.3.1 RemotelinkconnectionThissectionwillshowhowtolinkPIseriestoPCwith“Remotelink”andenter“Messagemenu”tosendmessagewhentheconnectionsuccessful.UseRemotelinktoconnectPCwithUSBStep1. AfterlinkUSBcablebetweenPIseriesandPC,press“Power”keytopoweronPIseries.Step2. Movecurseto“RemoteLink”andpress“ENT”key.

2Getstarted Connection27Step3. Enter“RemoteI/FSelect”andChoose“USB”.Itwillgetreturnlastpagewhenpress”Enter”  Step4. Choose“Connect”. Step5. InPhoenixVolerorEverlink,ClickCommsetupwillshowthemodelnumber.SuccessfullyconnectedtoPC.

2Getstarted Connection28MessageMenu Everlink,ControlCenterandPIseriescansendmessagetoPIseries.Press“Fn”+”^”keytoenterMessageMenu.   ReadpriorityMsg.:Itshowstheprioritymessageyoureceive. ReadMsg.:Itshowsthemessageyousent. SendMsg.:  ToEverlink:“Sendto”is9000 ToControlCenter:“Sendto”is9001 TootherPIseriesdevice:“Sendto”defaultdependsonSNlastfourdigits.TochangeID,referto“EquipmentID”inSystemmenu.Important  SendingmessagerelyonEverlink.PI

2Getstarted Connection29seriesmustconnecttoEverlinkthenthemessagewillstarttosendandreceive.

2Getstarted Attachthehandstrap302.4 AttachthehandstrapSometimesyoumayneedtodosomethingandcan’tholdyourterminalonyourhand.Or,youmightaccidentallydropyourterminalbetweenuses.Attachthehandstrapisausefulwaytoresolvetheseissues.Youcanwrapthestraparoundyourhandtosecureittoyourhand,orhangitonyourhandtohavebothhandsfreetodootherthings.Toattachthehandstrap,dothis:1. Pinchthesmallloopandthreaditintothetwosquareholesunderthebatterycover.

2Getstarted Attachthehandstrap312. Threadthebigloopintothesmallloop,andpullthebiglooptotieaknot.Important  Usehandstrapwhenyoucollectbarcodeincasedropaccident.PIseriesmightshutdowntoprotectdataafterdrop. 

2Getstarted Tag‐60(PI‐1060)322.5 Tag‐60(PI‐1060)StartTag‐60up1. HoldTag‐60bottom,presslatchtoremovecover. 2. RemovebatteryinsulationtostartTag‐60up. 3. Makesurebatteryisintheslotandclosecoverback.

2Getstarted Tag‐60(PI‐1060)33InsertorreplacingBattery1. HoldTag‐60bottomcover,presslatchtoremovecover. 2. ReplaceCR‐2032coinbattery.Makesurepositiveelectrodeisup.  3. Makesurebatteryisintheslotandclosecoverback. TopStraphole

2Getstarted Tag‐60(PI‐1060)34Topcaseisdesigned3holesforplacingTag‐60easily.AttachastraponTag‐60canhangingiteverywhereandalsopreventdropdamage.

3Controlsandsettings UserMenu353 ControlsandsettingsPIseriesoffersthreedifferentlayermenus.UserMenuisforgeneralusers,SystemMenuisforsupervisorsormanagers,andSupervisorMenuisforsystemadministratorsorengineers.Besides,pressFn+^canenterMessageMenuThischapterprovidesinformationaboutthesemenus.3.1 UserMenuUserMenuincludesthreefrequentlyusedsettings.Youcanusethemtorunyourprogram,connectyourterminaltoacomputerorotherdevice,ordisplayyourterminal’sinformation(viaEverlink).

3Controlsandsettings UserMenu363.1.1 RunProgramItshowstheprogramyoudownloadfromyourcomputer.Torunaprogram,justselectitandpressENT.Ifthere’snoprogram,itwilltellyou“Noprogramfile.”Formoreinformationabouthowtoconnecttoacomputeranddownloadprogramsfromit,seePhoenixVolerorEverlinkUserguide.Note  DefaultsettingbetweenPISeriesandProgramisindividual 3.1.2 RemoteLinkItisforyoutoconnectyourterminalwithEverlinkor

3Controlsandsettings UserMenu37PhoenixVolertocomputer.￭ Connect  Itconnectsyourterminaltocomputerafteryouselectaninterface.￭ RemoteI/FSelect  Itprovidesinterfaces,includingCOMport,USB,BluetoothandWI‐FI.Toconnectyourterminal,dothis:1. SelectRemoteLink>RemoteI/FSelect>COMport/USB/Bluetooth/WI‐FI.2. GouponelevelinthemenuandselectConnect.Note  IfyouwanttoconnectviaBluetoothorWI‐FI,youneedtoenterSupervisorMenuandsetupBluetoothconnectionorWI‐FIconnectionfirst.Aftercompletingthesetting,youcanconnectyourterminalfromUserMenuConnect.3.1.3 Scanner(HID)

3Controlsandsettings UserMenu38Itisforyoutoreadanduploadbarcodedataeasily.Onceyouhaveconnectiontocomputer.Press“SCAN”keytoreadbarcodeanditwilluploaddata.GotoCH4Application.seemoreinEverlinkuserguide.Note  Makesureyouturnonthedecodefunction(barcodedefault).3.1.4 InformationItdisplaysyourterminal’sinformation.IPL TheIPLversion.BOOT Thebootversion.Kernal Thekernelversion.Scanner Thescanner’sfirmwareversion.SN Theserialnumber.DefLang Thedisplaylanguage.

3Controlsandsettings SystemMenu393.2 SystemMenuUnderSystemMenu,youcanchangesystemsettingstomeetyourneedandrunsometeststoseeifyourterminalisworkingproperly.Presskey3+9+Powertoentersystemmenu.3.2.1 RemoteLinkSeethedescriptioninRemoteLinkinUserMenu.3.2.2 Diskinfo

3Controlsandsettings SystemMenu40Itprovidesthediskinformation,includingthefree,usedandtotaldiskspace.Bydefault,yourterminalhastwodisks:CandD.3.2.3 Timersetting￭ Setdate&time  Youcansetdateandtimehere.￭ Settimeformat  Youcansetthetimeformathere.Itprovidesthe12‐houror24‐hourclockandonlydisplayinStatusBar.C RAM FordatamemoryD Flash Forsystemanduser’sapplication

3Controlsandsettings SystemMenu413.2.4 EnvironmentItprovidessettingsforyoutoadjustdifferentworkplaceormatchyourpreference.￭ LCDcontrast  Itdeterminesthecontrastratio.Thebiggerthenumber,thelowerthecontrast(thedarkerthescreen).1~10￭ Backlighttimer  Itdetermineshowlongthebacklightstaysonafteryoupressakey.1~65535.Set0willalwayson.￭ Autoofftimer  Itturnsoffyourterminalafteracertainamountoftimeelapsed.Theunitoftimeisthesecond.Ifyousetit0,yourterminalisalwaysturnedon.30~65535 ￭ AlwaysonifDCin  ItwillalwaysonwhenyouplugDCpower.Defaultisdisable.

3Controlsandsettings SystemMenu42￭ Keyclick  Youcanturnonorturnoffthesoundofkeypad.￭ Vibration  Itdetermineshowlongyourterminalvibrates.Theunitis0.1second,rangeis1~255.Set0willturnitoff.3.2.5 TestItprovidesvarioustestsforyoutocheckyourterminalsystem.￭ Memorytest  Itchecksifthememorycanbewrittenandreadproperly.Notethatthistestremovesalldatastoredinthememory,soremembertosaveyourfilesinadvance.￭ Buzzertest  Itchecksifthebuzzercanmakesoundproperly.You’llhearthesoundrepeatedlyplaysfrom

3Controlsandsettings SystemMenu43hightolowandfromlowtohigh.Ifthesoundisplayedsmoothly,itmeansthebuzzerworksproperly,otherwisethebuzzermayhavesomeissues.￭ LCD&LEDtest  ItchecksiftheLCDdisplayhasbadpixels.￭ Keypadtest  Itchecksifthekeypadworksproperlywhenyoupressit.￭ Linkingporttest  Itchecksiftheportworksproperly.Youneedtosetaporttorunthistest.Formoreinformationabouttheportsetting,seethedescriptioninSettinginSupervisorMenu.Afteryousetaport,dothis:1. Selecttheportyouwanttotest,andpressENT.2. Yourterminalwillshowifthetestissuccessfulorfailedafterthetestiscomplete.￭ Scannertest  ItchecksifyourterminalcanreadbarcodeswhenyoupressSCANtoscanbarcodes.Ifthescanissuccessful,yourterminalwillvibrateanddisplaythebarcodedata.Note  Whenyoudoscannertesttobarcode,turnonthefunctioninBarcodeconfig(SupervisorMenu).

3Controlsandsettings SystemMenu443.2.6 SysteminfoSeethedescriptioninInformationinUserMenu.

3Controlsandsettings SupervisorMenu453.3 SupervisorMenu(1+3+0+PWR)SupervisorMenuprovidesadvancedsettingsforyoutoconfigure.Toprotectthesettingsfrombeingchangedeasily,youneedtoenterapasswordtoaccessthemenu.Bydefault,thepasswordisfivezeros(00000).

3Controlsandsettings SupervisorMenu463.3.1 RemoteLinkItisforyoutoconnectyourterminalwithEverlinkorPhoenixVolertocomputer.￭ Connect  Itconnectsyourterminaltocomputerafteryouselectaninterface.￭ RemoteI/FSelect  Itprovidesinterfaces,includingCOMport,BluetoothandWI‐FI.￭ RemoteI/FSet  Ithasthreeoptions:∙ COMport  Youcanselectabaudhere.

3Controlsandsettings SupervisorMenu47∙ Bluetooth  Ithasthreeoptions:1. Bluetoothsetting:(1) Devicename:Yourterminal’sname.Bydefault,thenameistheserialnumber.(2) PINcode:ThepasskeyforaBluetoothconnection.Bydefault,thecodeisfourzeros(0000).(3) Securitymode:Ithastwooptions.a. Security:YourterminalwillaskotherdevicestoenteraPINcodewhentheytrytoconnecttoyourterminal.b. Encryption:Itencryptstheconnectiontopreventdatatheft.(4) Inquirytimeout:Itdetermineshowlongyourterminalstopssearchingotherdevicesafteracertainamountoftimeelapses.(5) Maxresponse:Itdeterminesthemaximumnumberofconnectabledevicesyourterminallists.(6) Setpeerdevice:Ithastwooptions.a. Setbysearch:Searchotherdevicesintheneighborhood.b. Setbykeyin:Searchanotherdeviceby

3Controlsandsettings SupervisorMenu48enteringitsBluetoothMACaddress.2. Bluetoothtest:YoucanusethisoptiontotesttheBluetoothconnectionafteryourterminalconnectstoadevice.3. Bluetoothinfo:ItdisplaysBluetoothinformation,includingthelocaladdress,devicenameandlinkaddress.∙ WI‐FIIthasthreeoptions1. Setting(1) WI‐FISSID:a. Setbysearch:SearchWI‐FIsignalintheneighborhood.b. Setbykeyin:TypeNewSSIDtoconnecttheWI‐FIyouprefer.(2) Network:Itisthesameascomputernetwork.TheDefaultis“Enable”DHCPtoautogetIPAddress,SubnetMaskandGateway.Oryoucan“Disable”DHCPtosetyourWI‐FIdata.(3) Connectsetting:Type“NewIP”and“NewPort”togetconnection. (4) SystemScale:Thereare3Leveltochoose.Thedefaultis“High”

3Controlsandsettings SupervisorMenu49(5) PowerSaving:IfDisable,WI‐FImodulewillalwaysawaketotransmitdata.Otherwise,WI‐FIwillautomaticallyturnoff.   2. TCPTest:TestWI‐FIconnection,theprocessneedtowaitabout3~15seconds.PIserieswillshowtheconnectsuccessoffailonthescreen. 3. Information:ItdisplaysWI‐FIinformation. (1) Remoteport:showthepageisunderremoteport. (2) MAC:ShowMACaddressafteryouconnect. (3) DHCP:ThestatusisEnableorDisable.(4) rIP:CurrentremoteIPAddress.(5) rPort:CurrentremotePort.3.3.2 Formatdisk

3Controlsandsettings SupervisorMenu50Itformatsadiskinyourterminal.Thesystemwillaskyoutoconfirmifyouwanttoformat,becauseitwillremovealldatastoredinthedisk.￭ FormatC  FormattheCdisk.￭ FormatD  FormattheDdisk.3.3.3 SettingItoffersavarietyofsettingsthatyoucanchangetomeetyourneed.￭ EquipmentID  Yourterminal’sID.ThedefaultIDisfourzeros(0000).YoucanreplaceitwithanewID.TheIDneedstobea4‐digitnumber.￭ BIOSPassword  ItisthepasswordofSupervisorMenu.Thepasswordneedstobea5‐digitnumber.￭ BIOSdefault  Itresetsallyourterminalsettings,includingthepasswordofSupervisorMenu.

3Controlsandsettings SupervisorMenu51￭ Environment  Itprovidessettingsforyoutoadjusttoadapttodifferentworkplacesormatchyourpreference.Forthefirstfiveoptions,seethedescriptioninEnvironmentinSystemMenu.∙ Poweron  ItdeterminesthescreendisplayedinUserMenuafteryouturnonyourterminal.1. Resume:ThesystemdisplaysthelastscreenyouvisitedinUserMenueverytimeyouturnonyourterminal.2. Reset:ThesystemdisplaysthedefaultscreeninUserMenueverytimeyouturnonyourterminal.∙ Statusbar  Youcanchooseifyouwanttodisplaythestatusbar.￭ Scanner  Itprovidesseveralsettingsforthescanningfunctionality.∙ Readingtest  SeethedescriptioninTestinSystemMenu.∙ Indication  Ithastwooptions:1. LED:YoucanturnonorturnofftheLED.2. Beep:Youcanturnonorturnoffbeeps.∙ CodeID  CodeIDisanidentifierforabarcode.Ithastwooptions:

3Controlsandsettings SupervisorMenu521. Transmission:Ithastwomodes:ProprietaryIDorAIMID.Youcanchooseeitherofthem.ProprietaryIDisdefinedbyArgox.AIMIDisdefinedbytheAIMorganization.2. Position:YoucaninsertthecodeIDbeforeorafterthebarcodedata.∙ InvertImage  Whenyouturnonthisfeature,youcanscanbothregularandinvertedbarcodes.∙ Preamble  Addacharacterorcharactersbeforeabarcode.∙ Postamble  Addacharacterorcharactersafterabarcode.∙ Barcodeconfig  Itprovidesseveralsettingsforeachbarcodetype.Changethemtomeetyourneed.Thelistbelowshowsthebarcodetypessystemdefaultsetting.BarCodeTypeONOFF1.Code‐11○2.Code‐39○3.Code‐93○4.Code‐128○5.EAN‐8○6.EAN‐13○7.UPC‐A○

3Controlsandsettings SupervisorMenu538.UPC‐E○9.Industrial25○10.Interleaved25○11.Standard25○12.MSI‐Plessey○13.UK‐Plessey○14.RSS14○15.RSSLimited○16.RSSExpanded○17.CODABAR○18.Telepen○19.Matrix2of5○20.ChinaPost○21.Pharmacode○￭ Language  Youcanchangethelanguageforthesystemtodisplayitemsintheuserinterface.Ithastwooptions:English,TC(TraditionalChinese)andSC(SimpleChinese).￭ Linkingport  Youcandecidewhichportyouwanttouseandconfigureitssettings.Tosetaport,dothis:1. InPortIFselect,selectaportanditsinterface.2. InPortIFsetup,selecttheportyouchooseinthepreviousstep,andconfigurethesettingsofits

3Controlsandsettings SupervisorMenu54interface.∙ PortIFselect  Ithasfourports.Selectoneofthemandchooseitsinterface.YoucanchooseCOM,USB,BluetoothandWI‐FI.Ifyoudon’twanttouseinterface,chooseNone.∙ PortIFsetup  ItprovidesthesettingsofCOM,BluetoothandWI‐FI.Formoreinformationaboutthesettings,seeRemoteLinkinSupervisorMenu.∙ Portinfo  Itdisplaystheportinformation.PressUpArrowandDownArrowtocheckdifferentports.￭ Freq.set(PI‐1060Only)ChangePI‐1060FrequencysettingtotriggerTag‐60∙ 868  SetPI‐1060toRF868MHzfrequencywhichisforEuropecommunication. ∙ 920  SetPI‐1060toRF920MHzfrequencywhichisfornonEuropecommunication.ImportantLinkingportisfordevelopmentusageandtransmitrawdata.Seemoreinformation,gotoCH2.3Connection

3Controlsandsettings SupervisorMenu553.3.4 InformationItdisplaysyourterminal’sinformation.IPL TheIPLversion.BOOT Thebootversion.Kernal Thekernelversion.Scanner Thescanner’sfirmwareversion.SN Theserialnumber.HW Ver. ThePCBA(PrintedCircuitBoardAssembly)version.HW Int. Thehardwareversion.DefLang Thedisplaylanguage.

4Applications SupervisorMenu564 ApplicationsArgoxprovidesmultipleapplicationsforcommunicationanddevelopmentsasbelow: Communication PhoenixVoler UploadandDownloadfirmwareorapplicationeasily.Recommenddeveloper. Everlink  ManagemultiplePIserieswithfilestransmission,messagesendingandhistorydatafunction. Controlcenter Remote‐endofmanageprogramcanlinkmultipleEverlinkandprovideCloudoperation.DevelopmentapplicationSkywalker UserfriendlysoftwaredevelopmentkitGotoArgoxwebsitetogetmoreapplicationsanduserguidehttp://www.argox.com/content2011.php?sno=0000033NotePISeriesaccept“.bas”and“.bin”filefromBasicandCcompiler.

5Troubleshooting Hardwareissues575 Troubleshooting5.1 HardwareissuesSpeakerisnotworkingorvolumeistoolow.￭ Makesurethespeakerholeisnotblocked.￭ Testisinthesystemmenu,useTesttocheckspeaker.Keypaddoesnotresponse.￭ Testisinthesystemmenu,useTesttocheckkeypad.￭ Thesystemmightbecrush.UseScan+Powerkeytowarmresetorcoldreset(hold5seconds).Myterminalkeepsturningitselfofforcannotopen.￭ Ifyou’reusingbatteries,checkthemandseeiftheyneedtobecharged.￭ IfyourterminalisconnectedusingUSBorRS‐232cable,makesurethecableistightlyplugged.￭ ThedurationofAutooffTimeristooshort.SetitalongerdurationfromAutoofftimerinEnvironment

5Troubleshooting Communicationissues585.2 CommunicationissuesReceiveortransmitproblemonUSB￭ CheckUSBconnectorispluggedcorrectly.￭ CheckRemoteLinksetisUSBandselecttherightPIseriesnameoncomputer.￭ RestartPIseriesandunplugtheUSBandtryagain.ReceiveortransmitproblemonRS‐232￭ CheckRS‐232connectorispluggedcorrectly.￭ CheckRemoteLinksetisCOMportandselectthesameportoncomputer.￭ RestartPIseriesandunplugtheRS‐232andtryagain.ReceiveortransmitproblemonBluetooth￭ CheckRemoteLinksetisBluetoothportandBluetoothsettingiscorrect.￭ BesurePIseriesisintheBluetoothrange

5Troubleshooting Barcodescanningissues595.3 BarcodescanningissuesBarcodecannotberead ￭ Changetheanglebetweenthebarcodeandtheterminal.￭ Changethedistancebetweenthebarcodeandtheterminal.￭ Cleanthescanningwindowslightlyoftheterminal(makesurewithoutscratch).￭ Enabledthebarcodesymbologyinsupervisormenu>3.Setting>5.Scanner>7.Barcodeconfig.

Specifications 606 SpecificationsGeneralCharacteristicsOS ArgoxProprietaryCPU ARM926EJ‐SRAM 16/32MBDRAMROM 20/60MBFlashDisplay WhitegraymonoSTNLCD160*160Indicator LEDBlue,GreenandRed;Beeper;VibrationMotorKeypad 25Alpha‐Numerickeys(Including10functionkeys,3programmablehotkeys)Accessory Holder(Standard),PowerSupplyDimensions 145.0mm(L)x55.0mm(W)x26.0mm(H)Weight 230gwithbattery

Specifications 61Model PI‐1010 PI‐1030 PI‐1060 PI‐1230WPAN BluetoothClass2,BT2.1+EDRWLAN N/A Wi‐Fi802.11b/g/nN/A Wi‐Fi802.11b/g/nRF N/A N/A +15dbmmax.(Maxoutputpower)N/AI/OInterfaceUSB2.0/RS‐232

Specifications 62ScannerModel PI‐1010/PI‐1030/PI‐1060 PI‐1230ScannersystemCCD 2DAreaimagerResolution 3milatPCS90% 1D(5mils):Code392D(6.7miks):PDF417DepthoffieldCode393mil 40‐90mm Code39 5mil5mil 45‐140mm  EAN13 13mil20mil65‐570mm  Datamatrix 15milEAN13 13mil55‐435mm Scanningrate200scan/secDecodecapabilityCode‐11、Code‐39、Code‐93、Code‐128、EAN‐8、EAN‐13、UPC‐A、UPC‐E、Industrial25、Interleaved25、Standard25、MSI‐Plessey、UK‐Plessey、RSS14、RSSLimited、RSSExpanded、Autodiscriminatesallstandardone‐dimensionbarcodes;includingGS1databarPDF417,MicroPDF, CompositeCodes(CC‐A,CC‐B,

Specifications 63CODABAR、Telepen、Matrix2of5、ChinaPost、PharmacodeCC‐C)OCR‐A,OCR‐B,OCR‐C,Aztec(Standard,Inverse),MaxiCode,DataMatrix/ECC200(Standard,Inverse),QRCode,MicroQRExpansionStorage MicroSD(upto16GB)(factoryoption)DevelopingToolsSoftware SoftwareDevelopmentKit(SDK),Skywalker(Proprietaryapplicationsoftwaregenerator)ProgrammingLanguageClanguage,BASIClanguagePowerBattery AAsizeNIMHBattery*2(chargedbyUSBoroptionalpoweradapter)orAAsizeAlkaline*2(RecommendAAsizeNIMHBatteryfordailywork)

Specifications 64PowerRating 5Vdc2APhysicalandEnvironmentOperatingTemperature‐10℃~60℃  /14F~140FStorageTemperature‐20℃~70℃  /‐4F~158FHumidity 1)Operating:Non‐condensed10~90%2)Storage:Non‐condensed5~95%ImpactResistance1)Terminal1.2M/4ft2)IP54ElectrostaticDischarge1)+/‐15KVairdischarge2)+/‐8KVdirectdischargeEMCRegulationFCC,CE,BIS,BSMI

Specifications 65Model TAG‐60LightindicationBlueLEDSoundalert Buzzer>80dbA@10cm,programmablesoundpatternBeepingpatternProgrammablebeepingpatternRFSensitivity ‐110dbmtyp.Frequencybands(TBD)410~475,820~950MHzPower CR‐2032coinbattery,1yearsstandbyminimumDrop 1.5MDimensions 76.0mm(L)x50.0mm(W)x17.0mm(H)

AppendixA 66AppendixAScanModule(CCD)ConfigurationTable Default(*)Command1 Command2 Option/Limitation Indication LED indication Disable Enable * Buzzer indication Disable Enable * Transmission Preamble transmission Disable * Enable Postamble transmission Disable * Enable Code ID position Before code data * After code data Code ID transmission Disable * Proprietary ID AIM ID Code length transmission Disable * Enable Code name transmission Disable * Enable Disable *

AppendixA 67Case conversion Upper case Lower case Scan Double confirm 0 ~ 9 0 * Global min. code length 0 ~ 99 4 * Global max. code length 0 ~ 99 63 * Inverted image scan Disable * Enable String setting Prefix characters setting 0 * 0x00 ~ 0xff ASCII code 12 characters. Suffix characters setting 0 * 0x00 ~ 0xff ASCII code 12 characters. Preamble characters settings 0 * 0x00 ~ 0xff ASCII code 12 characters. Postamble characters settings 0 * 0x00 ~ 0xff ASCII code 12 characters. Code 11 Read Disable * Enable

AppendixA 68 Check-sum transmit /verify Disable/Disable Disable/One digit * Disable/Two digits Enable/One digit Enable/Two digits Max. code length 0 ~ 64 0 * Min. code length 0 ~ 64 0 * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <O> 0x00 ~ 0xff ASCII code(1 or 2 bytes) Code 39 Read Disable Enable * Check-sum transmit /verify Disable/Disable * Disable/Enable Enable /Enable Max. code length 0 ~ 64 0 * Min. code length 0 ~ 64

AppendixA 691 * Truncate leading 0 ~ 20 0 * Truncate ending 0 ~ 15 0 * Code ID setting <*> 0x00 ~ 0xff ASCII code(1 or 2 bytes) Format Standard * Full ASCII Start/stop transmission Disable * Enable Code 93 Read Disable * Enable Check-sum transmit /verify Disable/Disable Disable/Enable * Enable /Enable Max. code length 0 ~ 64 0 * Min. code length 0 ~ 64 0 * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 *

AppendixA 70 Code ID setting <&> 0x00 ~ 0xff ASCII code(1 or 2 bytes) Code 128 Read Disable Enable * Check-sum transmit /verify Disable/Disable Disable/Enable * Enable /Enable Max. code length 0 ~ 64 0 * Min. code length 0 ~ 64 1 * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <#> 0x00 ~ 0xff ASCII code(1 or 2 bytes) Format Standard * UCC.EAN 128 UCC/EAN 128 ID setting <#> 0x00 ~ 0xff ASCII code(1 bytes) 0x1D *

AppendixA 71Concatenation code 0x00 ~ 0xff ASCII code(1 bytes) Codabar Read Disable * Enable Check-sum transmit /verify Disable/Disable * Disable/Enable Enable /Enable Max. code length 0 ~ 64 0 * Min. code length 0 ~ 64 0 * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <%> 0x00 ~ 0xff ASCII code(1 or 2 bytes) Start/stop type ABCD/ABCD * abcd/abcd ABCD/TN*E abcd/tn*e Start/stop transmission Disable * Enable Disable

AppendixA 72EAN 8 Read Enable * Check-sum transmission Disable Enable * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <FF> 0x00 ~ 0xff ASCII code(1 or 2 bytes) Supplement digits None * 2 digits 5 digits 2, 5 digits UCC/EAN 128 2, UCC/EAN 128 5, UCC/EAN 128 All Truncation/expansion None * Truncate leading zero Expand to EAN 13 Expansion Disable * Enable EAN 13 Read Disable Enable *

AppendixA 73 Check-sum transmission Disable Enable * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <F> 0x00 ~ 0xff ASCII code(1 or 2 bytes) Supplement digits None * 2 digits 5 digits 2, 5 digits UCC/EAN 128 2, UCC/EAN 128 5, UCC/EAN 128 All ISBN/ISSN conversion Disable * Enable Industrial 2 of 5 Read Disable * Enable Max. code length 0 ~ 64 0 * Min. code length 0 ~ 64 0 *

AppendixA 74 Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <i> 0x00 ~ 0xff ASCII code(1 or 2 bytes) Interleaved 2 of 5 Read Disable Enable * Check-sum transmit /verify Disable/Disable * Disable/Enable Enable /Enable Max. code length 0 ~ 64 0 * Min. code length 0 ~ 64 0 * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <i> 0x00 ~ 0xff ASCII code(1 or 2 bytes) Standard 2 of 5 Read Disable * Enable

AppendixA 75 Check-sum transmit /verify Disable/Disable * Disable/Enable Enable /Enable Max. code length 0 ~ 64 0 * Min. code length 0 ~ 64 0 * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <i> 0x00 ~ 0xff ASCII code(1 or 2 bytes) MSI Plessey Read Disable * Enable Check-sum transmit /verify N/disable * N/MOD 10 N/Mod 10,10 N/mod 11,10 Y/ Mod10 Y/ Mod 10,10 Y/ Mod 11/10

AppendixA 76 Max. code length 0 ~ 64 0 * Min. code length 0 ~ 64 0 * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <@> 0x00 ~ 0xff ASCII code(1 or 2 bytes) UK Plessey Read Disable * Enable Check-sum transmit /verify Disable/Disable Disable/Enable * Enable /Enable Max. code length 0 ~ 64 0 * Min. code length 0 ~ 64 0 * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * <@>

AppendixA 77Code ID setting 0x00 ~ 0xff ASCII code(1 or 2 bytes) Telepen Read Disable * Enable Check-sum transmit /verify Disable/Disable * Disable/Enable Enable /Enable Max. code length 0 ~ 64 0 * Min. code length 0 ~ 64 0 * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <S> 0x00 ~ 0xff ASCII code(1 or 2 bytes) Format Numeric * Full ASCII UPCA Read Disable Enable * Check-sum transmission Disable Enable *

AppendixA 78 Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <A> 0x00 ~ 0xff ASCII code(1 or 2 bytes) Supplement digits None * 2 digits 5 digtis 2, 5 digits UCC/EAN 128 2, UCC/EAN 128 5, UCC/EAN 128 All Truncate/expansion None Truncate leading zero * Expand to EAN 13 UPCE Read Disable Enable * Check-sum transmission Disable Enable * Truncate ending 0 ~ 15 0 * <E>

AppendixA 79Code ID setting 0x00 ~ 0xff ASCII code(1 or 2 bytes) Supplement digits None * 2 digits 5 digits 2, 5 digits UCC/EAN 128 2, UCC/EAN 128 5, UCC/EAN 128 All Truncate/expansion None * Truncate leading zero Expand to EAN 13 Expand to UPCA Expansion Disable * Enable UPCE-1 Disable * Enable Matrix 25 Read Disable * Enable Check-sum transmit /verify Disable/Disable * Disable/Enable Enable /Enable Max. code length 0 ~ 64 0 *

AppendixA 80 Min. code length 0 ~ 64 0 * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <B> 0x00 ~ 0xff ASCII code(1 or 2 bytes) China post Read Disable * Enable Max. code length 0 ~ 64 11 * Min. code length 0 ~ 64 11 * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <t> 0x00 ~ 0xff ASCII code(1 or 2 bytes) RSS 14 Read Disable * Enable Truncate leading 0 ~ 15 0 *

AppendixA 81 Truncate ending 0 ~ 15 0 * Code ID setting <R4> 0x00 ~ 0xff ASCII code(1 or 2 bytes) UCC/EAN 128 emulation Disable * Enable RSS Limited Read Disable * Enable Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <RL> 0x00 ~ 0xff ASCII code(1 or 2 bytes) UCC/EAN 128 emulation Disable * Enable RSS Expanded Read Disable * Enable Max. code length 0 ~ 99 99 * Min. code length 0 ~ 99 1 *

AppendixA 82 Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <RX> 0x00 ~ 0xff ASCII code(1 or 2 bytes) UCC/EAN 128 emulation Disable * Enable Italian Pharmacode 39 Read Disable * Enable Max. code length 0 ~ 64 12 * Min. code length 0 ~ 64 9 * Truncate leading 0 ~ 15 0 * Truncate ending 0 ~ 15 0 * Code ID setting <p> 0x00 ~ 0xff ASCII code(1 or 2 bytes) Leading “A” Disable * Enable 

AppendixB 83AppendixBScanModule(2D)ConfigurationTableDefault(*)  Command1 Command2 Value 5 Indication 2 LED indication 0: Disable 1: Enable * 3 Buzzer indication 0: Disable 1: Enable * 4 Vibrator 0: Disable 1: Enable * 6 Transmission 8 Transmit Code ID 0: None(*) 1: AIM Code ID 2: Symbol Code ID 7 Scan 17 Timeout 5~99(0.1 sec.) Default: 99(9.9 sec) 20 Trigger Mode 0:Trigger(*) 7: Hand-Free Mode 9:Auto 21 Picklist Mode 0: Disable(*) 2: Enable 22 Same Barcode Timeout 5~99(0.1 sec.) Default: 6 (0.6 sec) 23 Mobile Phone/Display Mode 0: Disable(*) 3: Enable

AppendixB 8427 Illumination Power Level 1~10 (default: 10) 28 Decoding Illumination 0: Disable 1: Enable(*) 29 Decode Aiming Pattern 0: Disable 2: Enable(*) 32 Inverse 1D 0: Regular(*) 1: Inverse 2: Inverse Autodetect 10 Code 11 1 Read 0: Disable(*) 1: Enable 2 Check Digit Verification 0: Disable(*) 1: 1 Check Digit 2: 2 Check Digits 3 Transmit Check Digit(s) 0: Disable(*) 1: Enable 4 Length 1※1 0 ~ 55 (default: 4) 5 Length 2※1 0 ~ 55 (default: 55) 11 Code 39 1 Read 0: Disable 1: Enable(*) 2 Check Digit Verification 0: Disable(*) 1: Enable 3 Transmit Check Digit 0: Disable(*) 1: Enable 4 Length 1※1 0 ~ 55 (default: 2)

AppendixB 855 Length 2※1 0 ~ 55 (default: 55) 10 Full ASCII Conversion 0: Disable(*) 1: Enable 19 Code 32 Prefix 0: Disable(*) 1: Enable 20 Trioptic Code 39 0: Disable(*) 1: Enable 21 Convert Code 39 to Code 32 0: Disable(*) 1: Enable 12 Code 93 1 Read 0: Disable(*) 1: Enable 4 Length 1※1 0 ~ 55 (default: 4) 5 Length 2※1 0 ~ 55 (default: 55) 13 Code 128 1 Read 0: Disable 1: Enable(*) 4 Length 1※1 0 ~ 55 (default: 0) 5 Length 2※1 0 ~ 55 (default: 0) 14 ISBT 128 0: Disable 1: Enable(*) 15 GS1-128 0: Disable 1: Enable(*) 19 ISBT Concatenation 0: Disable(*) 1: Enable

AppendixB 862: Auto 20 Check ISBT Table 0: Disable 1: Enable(*) 21 ISBT Concatenation Redundancy 2 ~ 20 (default: 10) 14 Codabar 1 Read 0: Disable(*) 1: Enable 4 Length 1※1 0 ~ 55 (default: 5) 5 Length 2※1 0 ~ 55 (default: 55) 14 CLSI Editing 0: Disable(*) 1: Enable 15 NOTIS Editing 0: Disable(*) 1: Enable 15 EAN 8/JAN 8 1 Read 0: Disable 1: Enable(*) 20 Zero Extend 0: Disable(*) 1: Enable 16 EAN 13/JAN 13 1 Read 0: Disable 1: Enable(*) 18 Interleaved 2 of 5 1 Read 0: Disable 1: Enable(*) 2 Check Digit Verification 0: Disable(*) 1: USS Check Digit 2: OPCC Check Digits 3 Transmit Check Digit 0: Disable(*) 1: Enable

AppendixB 874 Length 1※1 0 ~ 55 (default: 14) 5 Length 2※1 0 ~ 55 (default: 0) 9 Convert to EAN 13 0: Disable(*) 1: Enable 20 MSI Plessey 1 Read 0: Disable(*) 1: Enable 2 Check Digits 0: One Check Digit(*) 1: Two Check Digits 3 Transmit Check Digit 0: Disable(*) 1: Enable 4 Length 1※1 0 ~ 55 (default: 4) 5 Length 2※1 0 ~ 55 (default: 55) 9 Check Digit Algorithm 0: MOD 10/MOD 11 1: MOD 10/MOD 10(*) 23 UPCA 1 Read 0: Disable 1: Enable(*) 3 Transmit Check Digit 0: Disable 1: Enable(*) 20 UPC-A Preamble 0: Disable 1: System Character Only(*) 2. System Character and Country Code 24 UPCE 1 Read 0: Disable 1: Enable(*)

AppendixB 883 Transmit Check Digit 0: Disable 1: Enable(*) 13 UPC-E1 0: Disable(*) 1: Enable 14 Convert UPC-E to UPC-A 0: Disable(*) 1: Enable 20 Transmit UPC-E1 Check Digit 0: Disable 1: Enable(*) 21 Convert UPC-E1 to UPC-A 0: Disable(*) 1: Enable 22 UPC-E Preamble 0: Disable 1: System Character Only(*) 2. System Character and Country Code 23 UPC-E1 Preamble 0: Disable 1: System Character Only(*) 2. System Character and Country Code 25 Matrix 2 of 5 1 Read 0: Disable(*) 1: Enable 2 Check Digit 0: Disable(*) 1: Enable 3 Transmit Check Digit 0: Disable(*) 1: Enable 4 Length 1※1 0 ~ 55 (default: 14) 5 Length 2※1 0 ~ 55 (default: 0)

AppendixB 8926 PDF-417 1 Read 0: Disable 1: Enable(*) 33 MicroPDF 1 Read 0: Disable(*) 1: Enable 11 Code 128 Emulation 0: Disable(*) 1: Enable 35 UPC/EAN 1 Bookland EAN 0: Disable(*) 1: Enable 2 Bookland ISBN Format 0: Bookland ISBN-10(*) 1: Bookland ISBN-13 3 UCC Coupon Extended Code 0: Disable(*) 1: Enable 5 Supplemental 0: Ignore supplemental (*) 1: Decode with Supplemental only 2: Auto discriminate Supplemental 3: Smart Supplemental Mode ※ Applies to EAN-13 starting with any prefix listed previously 4: Enable 378/379 Supplemental 5: Enable 978/979 Supplemental ※ If you select 978 Supplemental Mode and are scanning Bookland EAN bar codes, you should enable Bookland EAN, and select a format using

AppendixB 90Bookland ISBN Format. 6: Enable 414/419/434/439 Supplemental 7: Enable 977 Supplemental 8: Enable 491 Supplemental 9: Supplemental User-Programmable Type 1 ※ Applies to EAN-13 bar codes starting with a 3-digit user-defined prefix. Set this 3-digit prefix using User-Programmable Supplemental. 10: Supplemental User-Programmable Type 1 and 2 ※ Applies to EAN-13 bar codes starting with either of two 3-digit user-defined prefixes. Set the 3-digit prefixes using User-Programmable Supplemental. 11: Smart Supplemental Plus User-Programmable 1 ※ Applies to EAN-13 bar codes starting with any prefix listed previously or the user-defined prefix set using

AppendixB 91User-Programmable Supplemental. 12: Smart Supplemental Plus User-Programmable 1 and 2 ※ Applies to EAN-13 bar codes starting with any prefix listed previously or one of the two user-defined prefixes set using User-Programmable Supplemental. 6 Supplemental Redundancy 2 ~ 30 (default: 10) 7 User-Programmable Supplemental 1 -1 ~ 999(default:-1) 8 User-Programmable Supplemental 2 -1 ~ 999(default:-1) 9 UPC/EAN/JAN Supplemental AIM ID Format 0: Separate 1: Combined(*) 2: Separate Transmission 10 Coupon Report 0: Old Coupon Symbols 1: New Coupon Symbols(*) 2: Both Coupon Formats 11 ISSN EAN 0: Disable(*) 1: Enable 45 Australia Post 1 Read 0: Disable 1: Enable(*) 2 0: Auto(*)

AppendixB 92Format 1: Raw Format 2: Alphanumeric Encoding 3: Numeric Encoding 48 Japan Postal 1 Read 0: Disable 1: Enable(*) 49 KIX Code 1 Read 0: Disable 1: Enable(*) 51 USPS 1 Read 0: Disable(*) 1: Enable 52 UPU 1 Read 0: Disable(*) 1: Enable 53 Aztec 1 Read 0: Disable 1: Enable(*) 10 Inverse 0: Regular(*) 1: Inverse 2: Auto 54 Data Matrix 1 Read 0: Disable 1: Enable(*) 6 Inverse 0: Regular(*) 1: Inverse 2: Auto 55 Maxicode 1 Read 0: Disable 1: Enable(*) 58 OCR 1 Read 0: OCR off (*) 1: OCR-A 2: OCR-B 3. US Currency 4. MICR E13B

AppendixB 932 OCR-A Variant ※2 0: OCR-A Full ASCII(*) 1: OCR-A Reserved 1 2: OCR-A Reserved 2 3: OCR-A Banking 3 OCR-B Variant ※3 0: OCR-B Full ASCII(*) 1: OCR-B Banking 2: OCR-B Limited 3: OCR-B Travel Document Version 1 (TD1) 3 Line ID Cards 4: OCR-B Passport 6: OCR-B ISBN 10-Digit Book Numbers 7: OCR-B ISBN 10 or 13-Digit Book Numbers 8: OCR-B Travel Document Version 2 (TD2)2-Line ID Cards 9: OCR-B Visa Type A 10: OCR-B Visa Type B 14:Travel Document 2 or 3-Line ID Cards Auto-Detect 4 OCR Orientation 0: OCR Orientation 0(*) 1: OCR Orientation 270 Clockwise 2: OCR Orientation 180 Clockwise 3: OCR Orientation 90 Clockwise 4: OCR Orientation Omnidirectional 5 OCR Lines 1: OCR 1 Line(*) 2: OCR 2 Line

AppendixB 943: OCR 3 Line 6 OCR Minimum Characters 3(*) Range:3~100 7 OCR Maximum Characters 100(*) Range:3~100 8 OCR Quiet Zone 50(*) Range:20~99 9 Inverse OCR 0: Regular Only(*) 1: Inverse Only 2: Autodiscriminate 59 Discrete 2 of 5 1 Read 0: Disable(*) 1: Enable 4 Length 1※1 0 ~ 55 (default: 12) 5 Length 2※1 0 ~ 55 (default: 0) 60 Chinese 2 of 5 1 Read 0: Disable(*) 1: Enable 61 GS1 Data Bar 1 GS1 DataBar-14 0: Disable 1: Enable(*) 2 GS1 DataBar Limited 0: Disable(*) 1: Enable 3 GS1 DataBar Expanded 0: Disable(*) 1: Enable 4 Convert to UPC/EAN 0: Disable(*) 1: Enable 5 GS1 DataBar Limited Security Level 1: Level 1 2: Level 2 3: Level 3(*)

AppendixB 954: Level 4 62 Korean 3 of 5 1 Read 0: Disable(*) 1: Enable 63 Postal codes 1 US Postnet 0: Disable 1: Enable(*) 2 US Planet 0: Disable 1: Enable(*) 3 Transmit US Postal Check Digit 0: Disable 1: Enable(*) 4 UK Postal 0: Disable 1: Enable(*) 5 Transmit UK Postal Check Digit 0: Disable 1: Enable(*) 64 Composite 1 Composite CC-C 0: Disable(*) 1: Enable 2 Composite CC-A/B 0: Disable(*) 1: Enable 3 Composite TLC-39 0: Disable(*) 1: Enable 4 UPC Composite Mode 0: UPC Never Linked(*) 1: UPC Always Linked 2: Auto 5 GS1-128 Emulation Mode for UCC/EAN Composite Codes 0: Disable(*) 1: Enable 65 QR Code 1 Read 0: Disable 1: Enable(*) 2 0: Regular(*)

AppendixB 96Inverse 1: Inverse 2: Auto 66 Micro QR 1 Read 0: Disable 1: Enable(*) 68 Symbology Specific Security Levels 1 Redundancy Level 1: Level 1(*) 2: Level 2 3: Level 3 4: Level 4 2 Security Level 0: Level 0 1: Level 1(*) 2: Level 2 3: Level 3 3 Intercharacter Gap Size 6:Normal(*) 10:Large 

Navigation menu