Argox Information Co AS-8000CL Scanner User Manual

Argox Information Co Ltd Scanner

Users Manual

1Installation The AS-8000CL Wireless Imager is easy to install and use. Please see the following figure showing the steps to perform the installation. * Note: Turn off the host computer before installation. 1. Connect the interface (I/F) cable to the cradle. 2. Connect the power cord to the cradle. 3. Route the I/F cable and power cord through the notch. 4. Connect the I/F cable to the host computer communication port. 5. Connect the AC adapter to the wall outlet. 6. Place the imager in the cradle and verify the charge LED is flashing. Charge the battery for at least 8 hours before the first use. 7. To verify operation, please link the imager with cradle first (Refer to “Wireless Connection” in page 6). Point the imager at the barcode and pull the trigger. The imager should emit a beep indicating that the barcode has been scanned and transmitted to the cradle successfully.
2How To Scan 1. The imager must be pointed at slight angle to the barcode so that the light reflected off the barcode can be seen by the imager. Do not hold the imager perpendicular to the barcode. 2. The scan line must cross the entire barcode. The imager can not read the barcode data without seeing the entire barcode.
3Troubleshooting If the imager can not operate properly, the following checks should be performed: 1. The cradle uses an external power supply and the external power supply has failed, the imager will not operate. Change the power supply with a known good power supply and reset the imager. 2. Verify the interface cable is securely connected to the host computer. Consult your technical support personnel or refer to your host system manual to verify the proper connection for the imager.
43. Verify the interface cable is securely connected to the cradle. 4. Check that the barcodes are of sufficient quality to be recognized by the imager. Wrinkled, smudged, or torn labels will cause the imager to not read at all. Scan a known good label to check the imager’s read operation.
5 5. Ensure that the cradle’s interface type is compatible with the host computer by consulting your host system manual.
6Wireless Connection Linking the imager with the cradle Follow these instructions to link the two devices: 1. Connect power to the cradle. The radio LED (marked with a light symbol) will blink amber and the cradle will beep. 2. To ensure the cradle is unlinked from any other imager, check if the cradle send inquiry beep or not (see Inquiry Beep Control in page 18). 3. Read the link label on the bottom of the cradle with the imager. The imager will sound a good read beep and the LED will flash amber. 4. Re-place the imager in the cradle to continue the charge. Once an imager is linked to a cradle, they will remain linked until specific action is taken to unlink them (see Unlinking). They will remain linked if the cradle is unplugged, if the battery is removed from the imager or if the entire charge is used up, and if the imager is taken out of range of the cradle. Under normal operation, scanning of the link label will only be required once in the life of the product.
7 Unlinking There are three ways to unlink an imager from a cradle: Force imager to disconnect and sleep 1. Scan the “Force imager to disconnect and sleep” barcode – Reading the unlink barcode above while the imager is in range of the cradle will break the link between the two devices and allow another imager to link to the cradle. It will also have the imager in Deep Sleep Mode. If the barcode is read when the imager is out of range of its linked cradle, the imager will unlink, but the cradle will remain linked to the imager and will not allow another imager to be linked to it. In this case, you may perform the item 2 below to link another imager. 2. Scan the Link Label and put on the original cradle – If the cradle is linked with an imager and the original pair was stopped by out of range of the cradle or out of battery of the imager, scan the link label of the cradle with a new imager and then put on the cradle, the cradle will drop the original pair and establish a new link with the new imager. 3. Scan the Link Label on an alternate cradle – Scanning the link label on a cradle will drop the link between the original pair and establish a link between the imager and new cradle. If the new link is performed within range of the old cradle, it is free to establish a link to the next imager that reads its link label. If it is done outside of the range of the old cradle, it retains its old link and will not allow a new imager to link to it until a new imager scan the link label and put on the cradle. *$%-$$ZZ%%*
8Battery Charging The imager contains a 1000mAh Lithium-Ion rechargeable battery. A full charged battery will provide up to 15,000 scans over a 12 hours period. Actual charge life on the imager will depend on the configuration of how the imager is configured via the programmable feature in this manual; in particular, Deep Sleep Mode settings can impact battery life. When the imager is placed in the cradle, the battery will automatically charge. While charging is taking place, the charging LED (marked with a battery symbol) will blink green. When the battery is fully charged, the charging LED will stay on a solid green. If there is an error in charging either with a failure in the charging circuit or with a failure of the battery, the charging LED will flash red. When this happens, the battery needs to be replaced.
9How to Change the Battery In case the contained battery inside the imager needs to be replaced, please follow the procedures below: 1. Loosen the screw at the bottom of the imager. 2. Take off the battery container out of the imager. 5. Use a new battery pack and replace the used one. 3. Disconnect the battery cable connector from the handle board. 4. Remove the used battery from the battery container.
10 Note: DO NOT touch the PCBA inside the imager when replacing the battery. Improper operation may damage the imager. 6. Place the new battery into the battery container. 7. Connect the battery cable connector to the handle board. 8. Put the battery container back to the imager handle. 9. Fasten the screw to the imager.
11Wireless Features The AS-8000CL Wireless model includes an imager and a cradle. When the imager and cradle are linked together, the imager will read and decode barcodes and transmit them via a Wireless radio to the cradle. The cradle will then transmit the barcode data to the host computer over the host cable. The host interfaces available from the cradle are RS-232, Keyboard wedge, and USB as a normal corded imager.
12 Auto Update When this feature is enabled, an imager and its linked cradle can automatically ensure they stay in sync with regard to firmware and/or configuration. This is accomplished by the linked imager and cradle comparing firmware version number and configuration file check sum. If either is different, the cradle will automatically update the imager with its firmware/configuration. If the units are linked, any changes made to the cradle’s configuration through the scan utility software will automatically be sent to the imager at the completion of the programming session. By the same token, any changes made to the linked imager’s configuration will be transmitted to the cradle at the end of the programming session. The following options are available for Auto Update: z Enable configuration and firmware auto update – Allows both configuration and firmware updating (Default). z Enable configuration auto update only – Allows only configuration updating. *$%-1BA00%%**$%-1BA01%%*
13 z Enable firmware auto update only – Allows only firmware updating. z Disable auto update – No automatic updates will be performed. *$%-1BA02%%**$%-1BA03%%*
14 Deep Sleep Mode The WIRELESS imager can be placed into Deep Sleep Mode after this programmed duration (since the units’ last scanning activity). Press its trigger to wake the imager form this mode. z Disable Deep Sleep Mode (Default) z Duration 10 minutes - Force imager into deep sleep mode if there is no barcode read in 10 minutes. z Duration 30 minutes - Force imager into deep sleep mode if there is no barcode read in 30 minutes. z Duration 60 minutes - Force imager into deep sleep mode if there is no barcode read in 60 minutes. z Duration 90 minutes - Force imager into deep sleep mode if there is no barcode read in 90 minutes. *$%-7AJ00%%**$%-7AJ01%%**$%-7AJ06%%**$%-7AJ03%%**$%-7AJ09%%*
15 Handcuff Mode (Leash Alarm) When enabled, the Leash Alarm will force the imager to sound an alarm for a preprogrammed length of time to notify if an imager is leaving the immediate vicinity of the cradle. This is especially useful in instances where the imager might inadvertently have been placed in a bag or cart. z Disable Handcuff Mode (Default) z Alarm for 10 seconds when out of range z Alarm for 30 seconds when out of range z Alarm for 60 seconds when out of range *$%-7AM00%%**$%-7AM30%%**$%-7AM60%%**$%-7AM10%%*
16 Wireless Connectivity The AS-8000CL can be linked to any Bluetooth (BT) enabled device which can accept such a connection with other devices. To implement this feature, user should set the imager to “Cradle/Dongle connection auto detection” first. And then set the PIN code to 0000 assigned to the target Bluetooth device. In this case, the PIN code of the Bluetooth enabled device should be set to 0000 to be identical with your imager. z Cradle connection only – The imager can be used only with cradle (Default). z Cradle/Dongle connection auto detection – The imager can be linked to either a cradle or other Bluetooth enabled devices. z Set PIN code to 0000 Note: The imager only support “Serial Port Profile” under “Dongle connection” *$%-$0000%%**$%-1AB00%%**$%-1AB01%%*
17 Wireless Connectivity (continued) User is also allowed to set any four- to six-character PIN code assigned to the target Bluetooth device using the setting procedures below: STATE CODE Cradle/Dongle connection auto detection Program Begin PIN setting PIN no. (Set 4~6 character) End PIN setting *$%-1AB01%%**%$$**$%+PRO**/0**/1**/2**/3**/4**/5**/6**/7**/8**/9**#PIN*
18 Inquiry Beep Control When the cradle is not linked to an imager, the Radio LED will blink amber and the cradle will beep. This beep can be disabled or reconfigured to sound for different durations by using the following programming barcodes. z Disable inquiry beep z Inquiry beep continuously (Default) z Inquiry beep every 10 seconds z Inquiry beep every 20 seconds z Inquiry beep every 30 seconds z Inquiry beep every 40 seconds *$%-5AJ00%%**$%-5AJ08%%**$%-5AJ01%%**$%-5AJ02%%**$%-5AJ03%%**$%-5AJ04%%*
19 z Inquiry beep every 50 seconds z Inquiry beep every 60 seconds z Inquiry beep every 70 seconds *$%-5AJ05%%**$%-5AJ06%%**$%-5AJ07%%*
20 Cradle Beep Loudness Control The beep loudness of cradle can be defined with the following levels. z Cradle beep off z Level 1 z Level 2 z Level 3 (Default) z Level 4 z Level 5 *$%-5AK00%%**$%-5AK01%%**$%-5AK02%%**$%-5AK03%%**$%-5AK04%%**$%-5AK05%%*
21 z Level 6 z Level 7 *$%-5AK06%%**$%-5AK07%%*
22 Additional Features Here list three additional features of AS-8000CL wireless imager for the convenience of use to users. z Download firmware from the cradle z Download configuration parameters from the cradle z Force cradle to reset the configuration – This feature will also force imager to reset the configuration to factory default. Note: To meet the regulation of air transportation, the wireless imager should disconnect with the cradle during shipment. All AS-8000CL wireless imagers are suggested to scan the following command before packaging into boxes and ship to customers. Force imager to disconnect and sleep *$%-+CP%%**$%-+CC%%**$%-+IC%%**$%-$$ZZ%%*
23 Default setting For each barcode shown as below: Code Type Read EnableChecksumVerification Enable Checksum Transmission Enable CodeIDUPC-A V V V A UPC-E V V V E EAN-13 V V V F EAN-8 V V V FFCode-39 V ＊Interleaved 2 of 5 V i Industrial 2 of 5 - - i Matrix 2 of 5 B Codabar %Code-128 V V # Code-93 V two digits & Code-11 V One digit OMSI/Plessey V @UK/Plessey V @Telepen S Standard 2 of 5 V V i China Post t Italian Pharmacode. p Code-16K - - PDF417 V - - EAN UCC Composite - - RCRSS-14 R4RSS-Limited RLRSS-Expanded RXMicro-PDF - - U
24Specification Depth-head 44.5 mm AS-8000CL Specification Model:AS-8000CL Operational Light Source 630 nm Visible Red LED Optical System 2048 pixel CCD (Charge-coupled device) Depth of Scan Field Up to 260mm (CODE 39, PSC=90%, 20mils) Scanning Width 50mm wide @ 0mm Scan Speed 30~450 scans/sec Resolution 0.1mm (4mils) Code39,PCS=90% Print Contrast 25% or more Scanning Angle Front: 60° Rear: 60° Yaw: 70° Decode Capability Auto-discriminates all standard barcodes and some 2D symbologies including PDF-417 and RSS code; Other symbologies can be ordered optionally Beeper Operation 7 tones or no beep Indicator on imager Green & Red led Mechanical Length 186 mm Width-handle 33 mm Width-head 75 mm Depth-handle 32 mm
25Weight Less than 165g (with a battery) Case material ABS (over molded at contact points) Cushion material Double injection Cradle interface RS232, Keyboard wedge, USB Electrical Input Voltage (Cradle) 5 VDC ± 10% VDC Power - Operating (Cradle) 5 VDC Power – Standby (Cradle) 5 VDC Current – Operating (Cradle) 120 mA Current – Standby (Cradle) 120 mA Charge Current (Cradle) 660 mA Input Voltage (Imager) 3.4V ~ 4.2V Power - Operating (Imager) 3.2V ~ 4.0V Power – Standby (Imager) 3.4V ~ 4.2V Current – Operating (Imager) 225 mA Current – Standby (Imager) 32 mA Current – Sleep (Imager) 2 mA Light Level Up to 40000 Lux
26Shock (Imager) 1.5m drop onto concrete Shock (Cradle) 0.9m drop onto concrete Contaminants Seals to resist airborne particulate contaminants (IP42) Ventilation None required Programming Programming method Manual (Reading special barcode), Windows configuration program Program upgrade Enabled by built-in flash memory Programmable characteristics Code type selection, check digit selection Decoding option Decoding option Transmitted character delay, Header selection, trailer selection, message suffix, good read beep tone and volume, scanner trigger selection Keyboard emulation type (intermessage delay, keyboard type and keyboard language) Serial interface type (ACK/NAK, Xon/Xoff, RTS/CTS, good read LED control, start/stop bits)
27Indications of AS-8000CL Imager: Status Green LED Red LED Orange LED Beeper Link established Blink once A special beep Loss link (handcuff mode enable Blink Sound like grasshopperLoss link (handcuff mode disable) Blink twiceA special beep Hardware fail Flash Program download Flash Program checksum fail Flash Data transmitting ON High freq. Beep for 300msecData trans. Fail ON for 300msec Error beepData trans. OK ON for 200msec Good beepLED Low battery (<3.2V) (Trigger is pressed) Flash
28 Cradle: Status Green LEDRed LEDOrange LED BeeperInquiry Blink Beeps once a secondConnecting Blink Link established ON Hardware fail Flash Data receiving from the scanner ON for 0.5sec Barcode data proof or transmitted Good beepData send to the host Fail Error beepProgram download Flash RF status LED Program checksum Fail Flash Idle Charging Blink Battery full ON Battery LED Battery/charger Fail Blink
29Programming the AS-8000CL To program the 8000CL, you must scan a series of programming barcode in the correct order. Fold out the back cover of this manual. You will see a table of alphanumeric barcodes, which are used to program the various options presented. To program each option, you must: 1. Scan the Program barcode on the parameter setting part. 2. Enter the option mode by scanning the Option Bar Code (also on the Parameter setting part). 3. To the right of the option barcode, the necessary alphanumeric inputs are listed. Scan these alphanumeric entries from the back fold out page. To confirm above steps, you must scan the Finish barcode on the back fold out page. 4. Once you have finished programming. Scan the Exit barcode, listed on the lower right hand corner of each parameter setting part.
30 Option Bar Code Option Alphanumeric Entry Interface selection Keyboard Wedge RS-232 Wand emulation USB Keyboard/RS-232 Auto detection Reserved 00＊ 01 02 03 04 05 Program ExitProgram Barcode Option Barcode Exit Barcode Back Fold Out Finish barcode
31ExitInterface Selection This cradle comes in one model and supports interfaces such as keyboard wedge, RS232 serial wedge, and USB interface. In most of the cases, simply selecting an appropriate cable with a device code will work for a specific interface. Interface selection: You can change factory interface default for other type interface. By plugging different cables, setting right interface, then the cradle will be changed to another interface. However, you must make sure which cable you need. Keyboard/RS232/UBS Auto detection: By setting this function, it will automatically select the Keyboard wedge or RS-232 or UBS interface for user. Option Bar Code Option Alphanumeric Entry Interface selection Keyboard WedgeRS-232 USB Keyboard /RS232/USB Auto detection 00 01 03 04＊ Program Note:＊-Default
32ExitKeyboard wedge As a keyboard interface, the cradle supports most of the popular PCs and IBM terminals. The installation of the wedge is a fairly simple process without any changes of software or hardware. Keyboard Type: Select keyboard type connector of your host computer. Cradle must be selected to the appropriate host interface cable converter. Option Bar Code Option Alphanumeric Entry Keyboard type IBM AT, PS/2 Reserved Reserved Reserved Reserved Reserved Reserved 00＊ 01 02 03 04 05 06 Program
33Keyboard wedge Keyboard Layout: The selecting of keyboard layout supports many country languages other than USA keyboard layout. First you need to confirm country language that you desire. In DOS, using command “keyb” to select the desirable keyboard layout or in WINDOWS entry “Control” then pops “Keyboard” to select country at “language” item. For details, please refer to your DOS or WINDOWS user’s manual. Keyboard Speed: By selecting, you can change output speed of data transmission to match with host computer. Generally, set 00 or 01 in working high speed. If some output characters of barcode have been lost, you may need to set 05 or 06 to match your host keyboard speed. Function Key: Set Enable, imager can output code as pressing function-key in your application program while the barcode datas contain ASCII value between 0116 to 1F16. Refer to ASCII table. Numeric Key: The Keypad has to be selected if your application program is only keypad numeric code acceptable. So, cradle will output code as press numeric keypad when it read numeric digit. (The keypad is in the right side of keyboard, and Num Lock control key is also on.) If Alt+Keypad is selected, the data characters will be transmitted as “Alt” + numbers. For example, when sending character “A”, the actual sending will be “Alt”+65. It is also useful when using non-English OS and keyboard layout. Option Bar Code Option Alphanumeric Entry Program
34 Exit Keyboard layout USA Belgium Danish France Germany Italian Portuguese Spanish Swedish Switzerland UK Latin American Japanese 00＊ 01 02 03 04 05 06 07 08 09 10 11 12 Keyboard speed 0-8 0 : high clock rate8 : low clock rate00-08 03 * Function key Disable Enable 00 01＊ Alpha/Numeric key Alphabetic key Numeric keypad(Num lock state only) Alt+Keypad 00＊ 01 02
35Keyboard wedge Caps Lock: By selecting Caps lock”ON” or Caps lock”OFF”, imager can get Caps Lock status. Power-on simulation: All of the PCs check the keyboard status during power-on selftest. It is recommended to Enable function if you are working without keyboard installation. It simulates keyboard timing and pass keyboard present status to the PC during power-on. Inter-character delay: This delay is inserted after each data characters transmitted. If the transmission speed is too high, the system may not be able to receive all characters. Adjust it and try out suited delay to make system work properly. Block transmission delay: It is a delay timer between barcode data output. The feature is used to transfer continually with shorter barcode data or multi-field scanning.
36Exit Option Bar Code Option Alphanumeric Entry Caps lock Caps lock”ON” Caps lock”OFF”00 01＊ Power-on simulation Disable Enable 00＊ 01 Inter-character delay 00-99 (msec) 00-99 02＊ Block transmission delay 00-99 (10 msec) 00-99 10＊ Program
37RS-232 CTS: Clear To Send (Hardware Signal) RTS: Request To Send (Hardware Signal) Xon: Transmit On (ASCII Code 1116) Xoff: Transmit Off (ASCII Code13 16) Flow control: None-The communication only uses TxD and RxD signals without regard for any hardware or software handshaking protocol. RTS/CTS-If the cradle wants to send the barcode data to host computer, it will issue the RTS signal first, wait for the CTS signal from the host computer, and then perform the normal data communication. If there is no replied CTS signal from the host computer after the timeout (Response Delay) duration, the imager will issue a 5 warning beeps. Xon/Xoff- When the host computer is unable to accept data, it sends a Xoff code to inform the cradle to suspend data transmission, and Xon to continue. ACK/NAK- When the ACK/NAK protocol is used, the cradle waits for an ACK (acknowledge) or (not acknowledge) from the host computer after data transmission, and will resend in response to a NAK. Inter-character delay: It is delay time between data character’s data output. It is also same as Inter-char. delay of keyboard wedge. Block transmission delay: It is a delay time between barcode data output. It is also same as Block transmission delay of keyboard wedge. Response delay: This delay is used for serial communication of the cradle to waiting for handshaking acknowledgment from the host computer.
38Exit Option Bar Code Option Alphanumeric Entry Flow control None RTS/CTS Xon/Xoff ACK/NAK RTS/CTS bracket mode 00＊ 01 02 03 04 Inter-character delay 00-99 (msec) 00-99 00＊ Block transmission delay 00-99 (10 msec) 00-99 00＊ Response delay 00-99 (100 msec) 00-99 20＊ Program
39Exit Option Bar Code Option Alphanumeric Entry Baud rate 300 BPS 600 BPS 1200 BPS 2400 BPS 4800 BPS 9600 BPS 19200 BPS 38400 BPS 00 01 02 03 04 05＊ 06 07 Parity None Odd Even 00＊ 01 02 Data bit 8 bits 7 bits 00＊ 01 Stop bit One bit Two bits 00＊ 01 Program
40Pin Assignments 10-pin AS Series 10-pin RJ-45 Connector Pin RS-232 Keyboard 1 I/F I/F 2 NA NC 3 TXD NC 4 NC CLK / PC 5 GND DATA / PC 6 CTS DATA / KB 7 RXD NC 8 RTS CLK / KB 9 GND GND 10 NC GND 12435678910
41 Keyboard Wedge PS/2 Connector (To Host Side): Pin Mini-DIN 6P Male Mini-DIN 6P Female1 DATA / PC DATA / KB 2 NC NC 3 GND GND 4 VCC (+5V) NA 5 CLK / PC CLK / KB 6 NC NC RS-232 DB-9F Connector (To Host Side): Pin Definition 1 NC 2 TXD 3 RXD 4 NC 5 GND 6 NC 7 CTS 8 RTS 9 NC 4 2 3 186975 4 3 1 2 534562 1 Mini-DIN 6P Male Connector6Mini-DIN 6P Female Connector
42Scan Scanning mode: Good-read off-The trigger button must be pressed to activate scanning. The light source of imager stops scanning when there is a successful reading or no code is decoded after the Stand-by duration elapsed. Momentary-The trigger button acts as a switch. Press button to activate scanning and release button to stop scanning. Alternate-The trigger button acts as a toggle switch. Press button to activate or stop scanning. Timeout off-The trigger button must be pressed to activate scanning, and imager stops scanning when no code is decoded after the Stand-by duration elapsed. Continue-Imager always keeps reading, and it does not matter when trigger button is pressed or duration is elapsed. Test only-For test of scan performance only. It is improper to be utilized to check the accuracy of transmitted data. Double read timeout: The imager will require a several times successful decoding to confirm the data when enabled. The more confirming times required, the more inhibitive miss-reading code will be shown. The Multi field scan Enable function won’t be able to work if set Double confirm. Double confirm: If the barcode has been scanned twice, then only the first barcode will be accepted. Supplement Check Counter: It will be more reliable to read the barcode with extension (supplement) like UPCE/A or EAN-8/13, but slow down the decoding speed when this counter is set more.
43Exit Option Bar Code Option Alphanumeric Entry Scanning mode Good-read off Momentary Alternate Timeout off Continue Test only 00 01＊ 02 03 04 05 Stand-by duration 01-99 (second) 00-99 06＊ Double read timeout 01-99 (10 msec) 01-99 50＊ Double confirm 00-09 (00: no double confirm) 00-09 00＊ Program
44Scan Global min./max. code length: These are to define the min/ max readable code length of all symbologies. Code length less than min. code length or more than max. code length will not be read. In popular, you can set the same value for both min. and max. reading length to force the fixed length barcode decoded. The values of setting have no effect on certain symbologies with fixed length. You can specify the settings for individual barcode by the min/max code length setting of each barcode. Notes 1): Please set the min/max length if you have special demand for individual barcode. 2): Include the Check sum digits if you want to set Global min/max code length. Inverted image scan: Set Enabled the imager will scan both black/white barcode with white/black background.
45Exit Option Bar Code Option Alphanumeric Entry Global min. code length00-99 00-99 04＊ Global max. code length00-99 00-99 99＊ Inverted image scan Disable Enable 00＊ 01 Program
46Indication Power on alert: After power-on the cradle it will generate an alert signal to indicate a successful self-test. LED indication: After each successful reading, the LED above the imager will light up to indicate a good barcode reading. Beeper indication: After each successful reading, the imager will beep buzzer to indicate a good barcode reading, and its Beep loudness, Beep tone freq. and Beep tone duration are adjustable. Beep loudness/Beep tone freq./Beep tone duration: You can adjust Beep Loudness, Beep tone and Beep duration for a good reading upon favorite usage.
47Exit Option Bar Code Option Alphanumeric Entry Power on alert Disable Enable 00 01＊ LED indication Disable Enable 00 01＊ Beeper indication Disable Enable 00 01＊ Beep loudness 00-07 (00 - off) 00-07 07＊ Beep tone freq. 00-99 (100Hz) 00-99 26＊ Beep tone duration 00-99 (10 msec) 00-99 08＊ Program
48UPCA Format Leading Zero Data Digits(11 Digits)Check Digit Read: Enable or disable the read function. Check-sum transmission: By setting Enable, checks sum will be transmitted. Truncate leading/ending: The leading or ending digits of barcode data characters can be truncated when these values are set to non-zero. It will beep instead of reading anything when the truncate value is more than the barcode data digits or the value of Truncate Leading is overlapped with that of the Ending. The maximum value of truncate digits is 15. Code ID setting: Code ID setting is a character used to represent the symbol upon a succeeding reading. A Code ID setting is prefixed to the data begin or end transmitted if the feature is selected. If you want application to transmit Code ID, you must set Code ID transmission to Enable first. Refer to Code ID transmission.
49Exit Option Bar Code Option Alphanumeric Entry Read Disable Enable 00 01＊ Check-sum transmissionDisable Enable 00 01＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < A >＊ Program
50UPCA Insertion group number selection: The imager offers max. two insertion groups for one symbology. By setting one or two digits to indicate which insertion group you want to insert. You may refer to Character insertion. The function is to insert specific characters as a group into transmitted data of selected symbologies. Enable the group insertion by selecting the group number. Example: Group 2 → set 02 or 20. Group 1 and 4 → set 14 or 41. Notes 1): Group number set to “0” means that no group insertion required. 2): Details about the Insert Group settings please refer to page 117~120, and page 126 ASCII code table. Supplement digits: The Supplement digits barcode is the supplemental 2 or 5 characters for WPC code. Format LeadingZero Data Digits(11 Digits)CheckDigitSupplement Digits 2 or 5 or UCC / EAN 128 Truncation / Expansion: The leading “0” digits of UPCA data characters can be truncated when the function is enabled.
51Exit Option Bar Code Option Alphanumeric Entry Insert group number selection 00-44 00-44 00＊ Supplement digits None 2 digits 5 digits 2,5 digits UCC/EAN 128 2, UCC/EAN 1285, UCC/EAN 128All 00＊ 01 02 03 04 05 06 07 Truncation/ Expansion None Truncate leading zero Expand to EAN1300 01＊ 02 The Program
52UPCE Read: Format Leading Zero Data Digits (6 Digits) Check Digits Check-sum transmission: By setting Enable, checks sum will be transmitted. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00 01＊ Check-sum transmission Disable Enable 00 01＊ Truncate leading 0-15 00-15 00＊ Program
53Exit Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < E >＊
54UPCE Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Supplement digits: Format Leading Zero Data Digits(6 Digits)CheckDigitSupplement Digits2 or 5 or UCC/EAN 128 Expansion: The expansion function is used only for UPCE and EAN-8 code reading. It extends to 13-digits with “0” digits when the feature is enabled. Example: Barcode “0123654” Output: “0012360000057” UPCE-1: Enable imager to read UPCE with leading digit 1. Option Bar Code Option Alphanumeric Entry Insert group number selection 00-44 00-44 00＊ Program
55Exit Supplement digits None 2 digits 5 digits 2,5 digits UCC/EAN 128 2, UCC/EAN 1285, UCC/EAN 128All 00＊ 01 02 03 04 05 06 07 Truncation/Expansion None Truncate leading zero Expand to EAN13Expand to UPCA00＊ 01 02 03 Expansion Disable Enable 00＊ 01 *OAM* UPCE-1 Disable Enable 00＊ 01
56EAN-13 Read: Format Data Digits (12 Digits) Check Digits Check-sum transmission: By setting Enable, checks sum will be transmitted. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Truncate leading zero: Refer to Truncation / Expansion of UPCA. The Option Bar Code Option Alphanumeric Entry Read Disable Enable 00 01＊ Check-sum transmission Disable Enable 00 01＊ Truncate leading 0-15 00-15 00＊ Program
57Exit Truncate ending 0-15 00-15 00＊
58EAN-13 Code ID setting: Refer to page 51 Insertion group number selection of UPCA. Insertion group number selection: Refer to Insertion group selection of UPCA. Supplement digits: Format Data Digits (12 Digits) Check Digits Supplement Digits 2 or 5 or UCC / EAN 128 ISBN/ISSN: The ISBN (International Standard Book Number) and ISSN (International Standard Serial Number) are two kinds of barcode for book and magazines. The ISBN is 10 digits with leading “978” and the ISSN is 8 digits with leading “977” of the “EAN-13” symbology. Example: Barcode “9789572222720” - Output: “9572222724” Example: Barcode “9771019248004” - Output: “10192484” Option Bar Code Option Alphanumeric Entry Code ID setting 00-ffH ASCII code 00-ffH < F >＊ Insert group number selection 00-44 00-44 00＊ Program
59Exit Supplement digits None 2 digits 5 digits 2,5 digits UCC/EAN 128 2, UCC/EAN 1285, UCC/EAN 128All 00＊ 01 02 03 04 05 06 07 ISBN/ISSN conversion Disable Enable 00＊ 01 ISBN ID setting 00-ffH ASCII code 00-ffH < I >＊
60EAN-8 Read: Format Data Digits (7 Digits) Check Digits Check-sum transmission: By setting Enable, checks sum will be transmitted. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00 01＊ Check-sum transmission Disable Enable 00 01＊ Truncate leading 0-15 00-15 00＊ Program
61Exit Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH, 00-ffH < FF >＊ Insert group number selection 00-44 00-44 00＊
62EAN-8 Supplement digits: Format Data Digits (7 Digits) Check Digits Supplement Digits 2 or 5 or UCC/EAN 128 Truncation / Expansion: Refer to Truncate Leading zero of UPCE. Expansion: Refer to Expansion of UPCE. Option Bar Code Option Alphanumeric Entry Supplement digits None 2 digits 5 digits 2,5 digits UCC/EAN 128 2, UCC/EAN 1285, UCC/EAN 128All 00＊ 01 02 03 04 05 06 07 Truncation / Expansion None Truncate leading zero Expand to EAN1300＊ 01 02 Program
63Exit Expansion Disable Enable 00＊ 01
64Code 39 Read: Format Start “★” Data Digits( Variable)Checksum (Optional) End“★” Check-sum verification: The checksum of Code-39 is optional and made as the sum module 43 of the numerical value of the data digits. Check-sum transmission: By setting Enable, checksum will be transmitted. Max./Min. code length: Each symbology has own Max./Min. Code Length. They can be set to qualify data entry. If their Max./Min. Code Length is zero, the Global Min./Max. Code Length is in effect. The length is defined as to the actual barcode data length to be sent. Label with length exceeds these limits will be rejected. Make sure that the Minimum length setting is no greater than the Maximum length setting, or otherwise all the labels of the symbology will not be readable. In particular, you can see the same value for both Minimum and Maximum reading length to force the fixed length barcode decoded. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00 01＊ Program
65Exit Check-sum verification Disable Enable 00＊ 01 Check-sum transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH <＊>
66Code 39 Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Format: The Full ASCII Code-39 is an enhanced set of Code-39 that is the data with total of 128 characters to represent Full ASCII code. It is combined one of the digits +, %, $ and/ with one of the alpha digits (A to Z). Append: This function allows several symbols to be concatenates and be treat as one single data entry. The imager will not transmit the embedded appending code (space for Code-39). If Enable and other symbols were read again with the appended code, then codes will be transmitted without Code ID, Preamble and Prefix. When a symbol was decoded without the appended code, the data will be transmitted without Code ID and Prefix, but the Postamble Suffix codes are appended. This function is used when the first number of code 39 is a space. Example: □123456. Start/end transmission: The start and end characters of Code-39 are“★”. You can transmit all data digits including two “★”. Option Bar Code Option Alphanumeric Entry Insert group number selection 00-44 00-44 00＊ Program
67Exit Format Standard Full ASCII 00＊ 01 Append Disable Enable 00＊ 01 Start/end transmission Disable Enable 00＊ 01
68Interleaved 2 of 5 Read: Format Data Digits (Variable) Checksum (Optional) Check-sum verification: The checksum is made as the sum module 10 of the numerical values of all data digits. Check-sum transmission: By setting Enable, checksum will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00 01＊ Check-sum verification Disable Enable 00＊ 01 Program
69Exit Check-sum transmission Disable Enable 00＊ 01 Max. code leading 00-64 00-64 00＊ Min. code leading 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < i >＊ Insert group number selection 00-44 00-44 00＊
70Industrial 2 of 5 Read: Format Data Digits (Variable) Checksum (Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Program
71Exit Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < i >＊ Insert group number selection 00-44 00-44 00＊
72Matrix 2 of 5 Eur Read: Format Data Digits (Variable) Checksum (Optional) Checksum Verification: The checksum is made as the sum module 10 of the numerical values of all data digits. Checksum Transmission: By setting Enable, checksum will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Checksum Verification Disable Enable 00＊ 01 Program
73Exit Checksum Transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < B >＊ Insert group number selection 00-44 00- 44 00＊
74Codabar Read: Format Checksum Verification: The checksum is made as the sum module 16 of the numerical values of all data digits. Checksum Transmission: By setting Enable, checksum will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Checksum Verification Disable Enable 00＊ 01 Start Data Digits (Variable) Checksum (Optional) End Program
75Exit Checksum Transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < % >＊
76ExitCodabar Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Start/End type: The Codabar has four pairs of Start/End pattern; you may select one pair to match your application. Start/End Transmission: Refer to Start/End Transmission of Code 39. Option Bar Code Option Alphanumeric Entry Insert group selection 00-44 00-44 00＊ Start/End type ABCD/ABCD abcd/abcd ABCD/TN*E Abcd/tn*e 00＊ 01 02 03 Start/End transmission Disable Enable 00 01＊ Program
77ExitCode-128 Read: Format Data Digits (Variable) Checksum (Optional) Checksum Verification: The checksum is made as the sum module 103 of all data digits. Checksum Transmission: By setting Enable, checksum will be transmitted. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00 01＊ Checksum Verification Disable Enable 00 01＊ Checksum Transmission Disable Enable 00＊ 01 Program
78Code-128 Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Format: The Code-128 can be translated to UCC/EAN-128 format if it starts with FNC1 character. The first FNC1 will be translated to “]C1”,and next to be a field separator code as <GS>(1D16). ]C1 Data <GS> Data ChecksumAppend: When the function is enabled, it won't show the data immediately if imager read the barcode includes FNC2 code. It will show all data until it read the barcode, which doesn't have FNC2 code. Option Bar Code Option Alphanumeric Entry Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ 0-15 00-15 00＊ Program
79ExitTruncate leading Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < # >＊ Insert group number selection 00-44 00-44 00＊ Format Standard UCC/EAN-12800＊ 01 Append Disable Enable 00＊ 01
80ExitCode-128 ISBT enable: This feature is commonly used in a blood bank for identification. ISBT concatenation timeout: This feature is to setup the timeout duration of ISBT concatenation. Field separator code: This feature is only used for UCC/EAN-128 format. This Field separator code means you can reassign second or after a FNC1 for your usage. The default of ASCII code is <GS>(1D16). UCC/ EAN 128 ID setting: To setting the code ID for UCC/EAN-128 output format. Option Bar Code Option Alphanumeric Entry ISBT enable Disable Enable normal00＊ 01 Field separator code 00-ffH ASCII code 00-ffH 1DH＊ UCC/EAN-128 ID setting 00-ffH ASCII code 00-ffH < # >＊ Program
81ExitCode-93 Read: Format Data Digits(Variable)Checksum1(Optional)Checksum2(Optional)Checksum Verification: The checksum is made as the sum module 47 of the numerical values of all data digits. Checksum Transmission: By setting Enable, checksum will be transmitted. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Checksum Verification Disable Enable (two digits) 00 01＊ Checksum Transmission Disable Enable 00＊ 01 Program
82Code-93 Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Program
83Exit Code ID setting 00-ffH ASCII code 00-ffH < & >＊ Insert group number selection 00-44 00-44 00＊
84Code-11 Read: Format Data Digits(Variable)Checksum1(Optional)Checksum2(Optional)Checksum Verification: The checksum is presented as the sum module 11 of all data digits. Checksum Transmission: By setting Enable, checksum1 and checksum2 will be transmitted upon your selected checksum verification method. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Checksum Verification Disable One digit Two digits 00 01＊ 02 Program
85Exit Checksum Transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < O >＊ Insert group number selection 00-44 00-44 00＊
86MSI/plessey Read: Format Data Digits(Variable)Checksum1(Optional)Checksum2(Optional)Checksum Verification: The MSI/Plessey has one or two optional checksum digits. The checksum is presented 3 kinds of method Mod10, Mod10/10 and Mod 11/10. The checksum1 and checksum2 will be calculated as the sum module 10 or 11 of the data digits. Checksum Transmission: By setting Enable, checksum1 and checksum2 will be transmitted upon your selected checksum verification method. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Checksum Verification Disable Mod 10 Mod 10/10 Mod 11/10 00 01＊ 02 03 Program
87Exit Checksum Transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < @ >＊ Insert group number selection 00-44 00-44 00＊
88UK/plessey Read: Format Data Digits (Variable) Checksum1+2 (Optional) Checksum Verification: The UK/Plessey has one or two optional checksum digits. The checksum1 and checksum2 will be calculated as the sum module 10 or 11 of the data digits. Checksum Transmission: By setting Enable, checksum will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Checksum Verification Disable Enable 00 01＊ Program
89Exit Checksum Transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < @ >＊ Insert group number selection 00-44 00-44 00＊
90Telepen Read: IATA (International Air Transport Association). Checksum Verification: The checksum is presented as the sum module 10 or 11 of the data digits. Checksum Transmission: By setting Enable, checksum will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Checksum Verification Disable Enable 00＊ 01 Checksum Transmission Disable Enable 00＊ 01 Program
91Exit Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < S >＊ Insert group number selection 00-44 00-44 00＊ Format Numeric only Full ASCII only 00＊ 01
92Standard 2 of 5 Read: Format Data Digits (Variable) Checksum1 (Optional) Check-sum verification: The checksum is made as the sum module 10 of the numerical values of all data digits. Check-sum transmission: By setting Enable, checksum will be transmitted. Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Check-sum verification Disable Enable 00＊ 01 Program *JAB*
93 Exit*JAC* Check-sum transmission Disable Enable 00＊ 01 Max. code length 00-64 00-64 00＊ Min. code length 00-64 00-64 00＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < i >＊ Insert group number selection 00-44 00-44 00＊
94China Post Read: Format Data Digits (Variable) Checksum1 (Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Max. code length 00-64 00-64 11＊ Min. code length 00-64 00-64 11＊ Program
95Exit Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < t >＊ Insert group number selection 00-44 01-44 00＊
96Italian Pharmacode (Code 32) Read: Format Data Digits (Variable) Checksum1 (Optional) Max./Min. code length: Refer to Max./Min. code length of Code-39. Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code Id setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Leading “A”: If this function is enabled, each prefix of data shall be A. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Max. code length 00-64 00-64 12＊ Program
97Exit Min. code length 00-64 00-64 09＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 01-ffH < p >＊ Insert group number selection 00-44 00-44 00＊ Leading “A” Disable Enable 00＊ 01
98Code-16K Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < >＊ Program
99Exit Insert group number selection 00-44 00-ffH 00-44 00＊
100PDF-417 Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA.
101 Exit Option Bar Code Option Alphanumeric Entry Read Disable Enable 00 01＊ Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < P >＊ Insert group number selection 00-44 00-44 00＊ *QAJ* Escape sequence transmit Disable Enable 00＊ 01 Program
102EAN UCC Composite For the coupon extended code application. Coupon extended code is a supplementary barcode that is printed to the right of the UPC/EAN in UCC/EAN-128 symbology. Option Bar Code Option Alphanumeric Entry *YAA* Read Disable Enable 00＊ 01 *YAF* Truncate leading 0-15 00-15 00＊ *YAG* Truncate ending 0-15 00-15 00＊ *YAH* Code ID setting 00-ffH ASCII code 00-ffH < RC >＊ *YAI* Insert group number selection 00-44 00-44 00＊ Program
103Exit*YAK* UCC / EAN128 emulation Disable Enable 00＊ 01
104RSS-14 Read: Format Data Digits (Variable) Checksum1 (Optional) Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. UCC/EAN 128 emulation: Refer to Transmission, Code ID transmission must be set as AIM ID enable. Then ]C1 will be identified as prefix of barcode data transmission. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Program
105Exit Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < R4 >＊ Insert group number selection 00-44 00-44 00＊ UCC/EAN128 emulation Disable Enable 00＊ 01
106RSS-Limited Read: Format Data Digits (Variable) Checksum1 (Optional) Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. UCC/EAN 128 emulation: Refer to UCC/EAN 128 emulation of RSS-14. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Truncate leading 0-15 00-15 00＊ Truncate ending 0-15 00-15 00＊ Program
107Exit Code ID setting 00-ffH ASCII code 00-ffH < RL >＊ Insert group number selection 00-44 00-44 00＊ UCC/EAN128 emulation Disable Enable 00＊ 01
108RSS-Expanded Read: Format Data Digits (Variable) Checksum1 (Optional) Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. UCC/EAN 128 emulation: Refer to UCC/EAN 128 emulation of RSS-14. Option Bar Code Option Alphanumeric Entry Read Disable Enable 00＊ 01 Truncate leading 0-15 00-15 00＊ Program
109Exit Truncate ending 0-15 00-15 00＊ Code ID setting 00-ffH ASCII code 00-ffH < RX >＊ Insert group number selection 00-44 00-44 00＊ UCC/EAN128 emulation Disable Enable 00＊ 01
110Micro-PDF Truncate leading/ending: Refer to Truncate leading/ending of UPCA. Code ID setting: Refer to Code ID setting of UPCA. Insertion group number selection: Refer to page 51 Insertion group number selection of UPCA. Option Bar Code Option Alphanumeric Entry *XAA* Read Disable Enable 00 01＊ *XAF* Truncate leading 0-15 00-15 00＊ *XAG* Truncate ending 0-15 00-15 00＊ *XAH* Code ID setting 00-ffH ASCII code 00-ffH < U >＊ Program
111Exit*XAI* Insert group number selection 00-44 00-44 00＊ *XAJ* Escape sequence transmit None GLI protocol ECI protocol 00 01 02＊
112String setting / Transmission (Prefix / Suffix) Prefix / Suffix characters setting: Characters defined as prefix or suffix characters will be transmitted immediately with the scanned data for all symbologies. Up to 22 ASCII characters can be defined as Prefix or Suffix. Format of barcode data transmission: Prefix Name Preamble ID Code LengthBarcode Data ID Postamble Suffix . Insert groups
113Exit Option Bar Code Option Alphanumeric Entry Prefix characters setting None 1-22 characters00＊ 00-ffH ASCII code Suffix characters setting None 1-22 characters0D＊ 00-ffH ASCII code Program
114String setting / Transmission (Preamble/Postamble) Preamble/ Postamble characters: Preamble or Postamble characters will be appended to the data automatically for all symbologies. However, the transmission will not activate unless Preamble / Postamble transmission is enabled. Preamble transmission: By setting Enable, Preamble will be appended before the data transmitted. Postamble transmission: By setting Enable, Postamble will be appended after the data is transmitted. Example: Add a prefix/suffix or preamble/postamble for all symbologies. In this example, you are sending a $ symbol as a prefix for all symbologies. Steps: 1) Scan Programming and Prefix characters setting barcode. 2) Use the ASCII code table to find the value of $→24. 3) Scan 2 and 4 from the barcode on the fold out back page. 4) Scan Finish from the barcode on the fold out page. 5) Scan Exit barcode.
115Exit Option Bar Code Option Alphanumeric Entry Preamble characters setting 1-22 characters “PREAMBLE”＊00-ffH ASCII code Preamble transmission Disable Enable 00＊ 01 Postamble characters setting 1-22 characters “POSTAMBLE”＊00-ffH ASCII code Postamble transmission Disable Enable 00＊ 01 Program
116String setting / Transmission (Insert Group Characters) Insert G1/G2/G3/G4 character setting: The imager supports inserting two groups with each group 22 characters into transmitted data of selected symbologies. The two groups can be inserted into scanned data of the selected symbologies or positioned at leading / ending of data. There are total four groups for utilization. Insert data group position: To define the position of a group to insert into bar code data. Please notice that the inserting position of a group must not exceed the code length; or the insertion will be positioned at the ending of data. Notice: Default value “00” indicates the group to be positioned at the leading of data. “64” represents for positioning the group at the ending of data. Insert data group setting procedure: i. Define the characters of groups for insertion. ii. Setup the inserting position of each group in scanned data. iii. Select one or two groups to insert into specific bar codes. Please refer to the setting pages of each bar code. Example: Barcode “1 2 3 4 5 6”. Output- Barcode “1 2 A B 3 4 C D 5 6”. Steps: 1) Scan Programming and Insert G1 characters setting barcode. 2) Use the ASCII code table to find the value of A→41,B→ 42. 3) Scan 4, 1 and 4, 2 from the barcode on the fold out back page. 4) Scan Finish from the barcode on the fold out page.
1175) Repeat the same procedure in Insert G2 characters setting. 6) Scan Exit barcode. 1) Insert data group 1-4 position. Please refer to the specific barcode that you want to use. 2) Insert data group 1-4 position: The imager offers 4 positions to insert among the symbol. The position default value is “00” to indicate no character insertion. Beside, make sure insertion positions are not greater than the symbols; otherwise the insertion data is not effective. Option Bar Code Option Alphanumeric Entry Insert G1 characters setting 1-22 characters “GROUP1”＊00-ffH ASCII code Insert G2 characters setting 1-22 characters “GROUP2”＊00-ffH ASCII code Insert G3 characters setting 1-22 characters “GROUP3”＊00-ffH ASCII code Program
118Exit Insert G4 characters setting 1-22 characters “GROUP4”＊00-ffH ASCII code Insert data group 1 position 00-64 (00: no insertion)00-64 00＊ Insert data group 2 position 00-64 (00: no insertion)00-64 00＊ Insert data group 3 position 00-64 (00: no insertion)00-64 00＊ Insert data group 4 position 00-64 (00: no insertion)00-64 00＊
119String setting / Transmission (Others) Code ID position: Upon your usage, the transmitting position of Code ID can be selected to place Before Code Data or After Code Data when it is transmitted. Code ID transmission: If your application is needed to transmit Code ID, you must set this to Proprietary ID or AIM ID. Code length transmission: A number of data digits can be transmitted before the code data when Enable is selected. The total length of the barcode is the number of barcode data except Truncate Leading/Ending Digits. And the length is a number with two digits. Code name transmission: This function is to show unknown barcode symbologies that include all readable symbologies of the imager. When Enable is selected, Code Name will be transmitted before code data, you will know what kind of barcode symbology is. Case conversion: Setup the scanned data characters to be transmitted all in upper case or lower case. For example: If upper case is selected, “12aBcDeF” will be converted and transmitted to host as “12ABCDEF”. Option Bar Code Option Alphanumeric Entry Program
120Exit Code ID position Before code dataAfter code data 00＊ 01 Code ID transmission Disable Proprietary ID AIM ID 00＊ 01 02 Code length transmission Disable Enable 00＊ 01 Code name transmission Disable Enable 00＊ 01 Case conversion (For barcode data only) Disable Upper case Lower case 00＊ 01 02
121Test Chart (Bar code samples marked with symbol “*” are enabled initially.) CODABAR-PARA CODE-11 PARA CODE-128 PARA * CODE-39 PARA * CODE-93 PARA EAN-13 PARA *
122PDF-417 * STANDRAD-25 PARA CODE-16K EAN-8 PARA * INDUSTRIAL-25 PARA UPCE PARA * 87549
123INTERLEAVED-25 PARA * MATRIX 25 PARA MSI/PLESSEY PARA UPCA PARA * UK/PLESSEY PARA RSS Micro-PDF *
124ASCII Code Table Note: For keyboard wedge only. L H 0 1 0 1 0 Null NUL DLE 1 Up F1 SOH DC1 2 Down F2 STX DC2 3 Left F3 ETX DC3 4 Right F4 EOT DC4 5 PgUp F5 ENQ NAK 6 PgDn F6 ACK SYN 7 F7 BEL ETB 8 Bs F8 BS CAN 9 Tab F9 HT EM A F10 LF SUB B Home Esc VT ESC C End F11 FF FS D Enter F12 CR GS E Insert Ctrl+ SO RS F Delete Alt+ SI US L H 2 3 4 5 6 7 0 SP 0 @ P ` p 1 ! 1 A Q a q 2 “ 2 B R b r 3 # 3 C S c s 4 $ 4 D T d t 5 % 5 E U e u 6 & 6 F V f v 7 ‘ 7 G W g w 8 ( 8 H X h x 9 ) 9 I Y i y A ★ : J Z j z B + ; K [ k ﹛ C ， < L ＼ l ︱ D - = M ] m ﹜ E . > N ^ n 〜 F / ? O _ o DEL
125Parameter Setting List Program Barcode standard parameter setting list If you wish to display the current barcode reading configuration of your AS-8000CL imager over the host terminal/computer, scan the Barcode standard parameter setting list bar code. System parameter setting list If you wish to display the current system configuration of your AS-8510 imager over the host terminal/computer, scan the System parameter setting list bar code. String setting list If you wish to display the string format list, scan the String setting list bar code. Exit
126Exit Query present cradle firmware version Program Firmware version list If you wish to display the cradle and imager firmware versions, scan the “Firmware version list” barcode. Reset cradle to factory default settings WARNING: Default value initialization If you wish to return the AS-8000CL imager to all the factory default settings, scan the above barcode will perform the feature. However, the cradle will be set to factory default settings at the same time. *$%-+IC%%*
127 0 1 2 3 4 5 6 7 8 9 ABCFinish FED
NOTICE: This equipment has been tested and complied with the limits for a Class a digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interface when the equipment is operated under a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interface to radio communications. Operation of this equipment in a residential area is likely to cause harmful interface in which case the user will be required to correct the interface at his own expenses. Note: All brands and trademarks shall belong to their respective owner. Note: Specification is subject to changes without notice. This device complies with Part 15 of the FCC Rules. Operation shall be subject to the following two conditions: (1) This device may not cause harmful interface, and(2) This device must accept any interface received, including interface that may cause undesirableoperation.
Using the ArgoxScan 8000CL The ArgoxScan can automatically scan barcode at a distance. Simply aim and pull the trigger. Code scanning is performed along the center of the light bar emitted from the reading window. This bar must cover the entire code (see “How to Scan” in page 2). Successful scanning shall be obtained by tilting the scanner with respect to the barcode to avoid direct reflections that impair the reading performance. Recommended Steps When the required settings have been configured, all settings are stored in non- volatile memory of scanner and cradle after reading EXIT Label. Recommended steps are as follows. 1) Host interface will be automatically detected. User does not need to set host interface for the cradle. 2) Set interface to optimize protocol of cradle with your host in interface section. 3) Set system control of scanner, such as specific adjustments double confirm, indicator and scanning mode which you prefer usage in system control section. 4) Set code options of scanner for your usage in code option section. You must make sure to enable the symbology first, then Min./Max. code length, code ID checksum and truncate digits are also converted. 5) Set string format of the scanner, such as preamble, postamble Prefix, suffix, code ID and code name transmission for your application in string format section. Note: If still not work properly. Please contact your dealer for further information.
警告使用者: 這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會被要求採取某些適當的對策。 低功率電波幅性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
警告： 電池若未妥善處理， 可能會導致爆炸。 請勿拆卸電池， 或用火銷毀電池。 請將電池放置於兒童拿不到的地方。 請使用專用充電器充電， 並請依照當地政府或法律規定妥善處理廢棄電池。 CAUTION: EXPLOSION HAZARD Do not disassemble, short circuit, heat the battery or dispose of in fire. Store battery pack in a proper place. Do not expose to temperature above 60℃/140℉. Use specified charger only. Please dispose of the used batteries following the rules or laws issued by the local government.
CONTENTS Chapter 1 Introduction Installation…………………………………………… 1How To Scan………………………………………… 2Troubleshooting……………………………………… 3Wireless Connection………………………………… 6Battery Charging…………………………………… 8Wireless Features…………………………………… 11Auto Update……………………………………… 12Deep Sleep Mode……………………………… 14Handcuff Mode (Leash Alarm)………………… 15Wireless Connectivity…………………………… 16Inquiry Beep control…………………………… 18Cradle Beep Loudness Control………………… 20Additional Features……………………………… 22Default Setting.……………………………………… 23Specification………………………………………… 24Indications of AS-8000CL..………………………… 27Imager…………………………………………… 27Cradle…………………………………………… 28Programming the AS-8000CL..…………………… 29 Chapter 2 Parameter Setting Interface………………………………………………… 31Interface Selection.………………………………… 31Keyboard wedge.…………………………………… 32RS-232.……………………………………………… 37Pin Assignments.…………………………………… 40 System Control……………………………………… 42Scan………………………………………………… 42Indication. …………………………………………… 46 Code Option…………………………………………… 48UPCA.………………………………………………… 48UPCE ………………………………………………… 52EAN-13.……………………………………………… 56
EAN-8 ………………………………………………… 60Code 39 ……………………………………………… 64Interleaved 2 of 5 …………………………………… 68Industrial 2 of 5 ……………………………………… 70Matrix 2 of 5 Eur …………………………………… 72Codabar ……………………………………………… 74Code-128 …………………………………………… 77Code-93 ……………………………………………… 81Code-11.……………………………………………… 84MSI/Plessey.………………………………………… 86UK/Plessey.………………………………………… 88Telepen.……………………………………………… 90Standard 2 of 5 ……………………………………… 92China Post …………………………………………… 94Italian pharmacode (Code 32)..…………………… 96Code-16K…………………………………………… 98PDF-417……………………………………………… 100EAN UCC Composite……………………………… 102RSS-14.……………………………………………… 104RSS-Limited………………………………………… 106RSS-Expanded……………………………………… 108Micro-PDF…………………………………………… 110 String Format…………………………………………… 112String Setting / Transmission (Prefix/Suffix)……… 112String Setting / Transmission (Preamble/Postamble)……………………………… 114String Setting / Transmission (Insert Group Characters)………………………… 116String Setting / Transmission (Others)…………… 119 Appendix………………………………………………… 121Test Chart.…………………………………………… 121ASCII Code Table …………………………………… 124Parameter setting List.……………………………… 125

Navigation menu