Arcadyan Technology HT2000W HT2000W wifi module User Manual Front End Module

Arcadyan Technology Corporation HT2000W wifi module Front End Module

Front-End Module User Manual

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 203068E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 18, 2014 1 PRELIMINARY DATA SHEET SKY85717-21: 5 GHz, 802.11ac Front-End Module 4BApplications  802.11ac set-top boxes, networking, and personal computer systems  PC cards, PCMCIA cards, mini-cards, and half mini-cards  WLAN enabled wireless video systems 0BFeatures  Integrated high performance 5 GHz PA, LNA with bypass, and SPDT  Fully-matched input and output  Integrated, positive slope power detector  Transmit loopback mode  Transmit gain: 28 dB  Receive gain: 12 dB  Output power: +19.5 dBm, MCS7, HT40  Output power: +18.5 dBm @ 1.8% EVM, MCS9, HT80  High linearity and high efficiency modes  Direct connection to battery with 5 V nominal supply voltage  Small, QFN (16-pin, 2.5 x 2.5 x 0.4 mm) package (MSL1, 260 C per JEDEC J-STD-020) Skyworks Pb-free products are compliant with all applicable legislation. For additional information, refer to Skyworks Definition of Lead (Pb)-Free, document number SQ04-0073. S3513VDETPA_ENGNDTXLNA_ENCRXGNDANTGNDRXGNDVDDGNDVCC2VCC1VLIN1234121110956781615 14 13 Figure 2. SKY85717-21 Pinout – 16-Pin QFN (Top View) PALNAS3512TXVC1VDET ANTRXPA_ENLNA_ENVLIN Figure 1. SKY85717-21 Block Diagram 1BDescription The SKY85717-21 is a highly-integrated, 5 GHz front-end module (FEM) incorporating a 5 GHz single-pole, double-throw (SPDT) transmit/receive (T/R) switch, a 5 GHz low-noise amplifier (LNA) with bypass, and a 5 GHz power amplifier (PA) intended for mobile/portable 802.11ac applications and systems. An enable/disable function is included that allows power savings during off mode. An integrated power detector with 20 dB of dynamic range is included to provide closed-loop power control within the system. The device is provided in a compact, 16-pin 2.5 x 2.5 x 0.4 mm Quad Flat No-Lead (QFN) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1.
PRELIMINARY DATA SHEET • SKY85717-21: FRONT-END MODULE Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 2 August 18, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203068E 5BTechnical Description The SKY85717-21 is comprised of a high performance 5 GHz PA, 5 GHz LNA, and broadband SPDT switch. The device is fully-matched, and requires few external components for optimal performance, which makes it ideal for small portable/mobile applications. The FEM provides up to +28 dB of gain over the frequency band. The LNA supports an enable/disable mode for power savings when not in receive mode and a bypass function for increased receive dynamic range. The PA can be shut off using the PA_EN signal (pin 6). 2BElectrical and Mechanical Specifications Signal pin assignments and functional pin descriptions are described in Table 1. The absolute maximum ratings of the SKY85717-21 are provided in Table 2. The recommended operating conditions are specified in Table 3 and electrical specifications are provided in Tables 4, 5, and 6. The state of the SKY85717-21 is determined by the logic provided in Table 7. 6BPackage and Handling Information Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY85717-21 is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Table 1. SKY85717-21 Signal Descriptions Pin Name Description Pin Name Description 1 GND Ground 9 VLIN Transmit linearity mode control 2 RX RF receive output 10 VCC1 Supply voltage 3 GND Ground 11 VCC2 Supply voltage 4 VDD LNA supply voltage and transmit bias 12 GND Ground 5 VDET Detector output voltage 13 ANT Antenna 6 PA_EN PA enable 14 GND Ground 7 GND Ground 15 CRX Switch control voltage 8 TX RF transmit input 16 LNA_EN LNA enable Note: N/C = No connect. Keep pin floating.
PRELIMINARY DATA SHEET • SKY85717-21: FRONT-END MODULE Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 203068E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 18, 2014 3 Table 2. SKY85717-21 Absolute Maximum Ratings (Note 1) Parameter Symbol Minimum Maximum Units Supply voltage (non-operating, no RF) VCC VDD –1 –1 +6 +6 V V DC input on control pin (PA_EN, LNA_EN, CRX, VLIN) VIN –0.3 +6.0 V Input power (ANT terminated in 50 Ω match) PIN +5 dBm Case operating temperature TA –40 +85 C Storage temperature TST –40 +140 C Electrostatic discharge: Human Body Model (HBM), Class 1C ESD 1000 V Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. SKY85717-21 Recommended Operating Conditions Parameter Symbol Minimum Typical Maximum Units Supply voltage relative to GND = 0 V VCC, VDD 3.9 5.0 5.5 V Operating temperature TA –40 +25 +85 C Table 4. SKY85717-21 Electrical Specifications: DC Characteristics (Note 1) (VCC = 5.0 V, PA_EN = 3.3 V, TA = 25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Supply current, high linearity mode ICC-A POUT = +20.5 dBm, VLIN = 3.3 V 230 260 mA Supply current, high efficiency mode ICC-A POUT = +20.5 dBm, VLIN = 0 V 220 240 mA Supply current ICC-OFF No RF applied, PA_EN = CRX = LNA_EN = 0 V 20 μA Quiescent current, high efficiency mode ICQ No RF 170 mA LNA supply current ICC_LNA LNA_EN = 3.3 V, CRX = 3.3 V 11 mA LNA bypass supply current ICC_LNA_BYP LNA_EN = 0 V, CRX = 3.3 V 200 μA TNote 1: Performance is guaranteed only under the conditions listed in this table.
PRELIMINARY DATA SHEET • SKY85717-21: FRONT-END MODULE Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 4 August 18, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203068E Table 5. SKY85717-21 Electrical Specifications: General (Note 1) (VCC = 5.0 V, PA_EN = 3.3 V, LNA_EN = CRX = 0 V, TA = 25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Transmit Characteristics Frequency range f 4900 5850 MHz Error Vector Magnitude, high linearity mode EVM 5150 to 5850 MHz, VLIN = 3.3 V: POUT = +19.5 dBm, MCS7, HT40 POUT = +18.5 dBm, MCS9, HT80 1.8 3.0 2.0 % % Error Vector Magnitude, high efficiency mode EVM 5150 to 5850 MHz, VLIN = 0 V: POUT = +19.5 dBm, MCS7, HT40 POUT = +18.5 dBm, MCS9, HT80 1.8 3.0 2.0 % % Output power POUT MCS0, mask compliance +22 +24 dBm Small signal gain S21 5150 to 5850 MHz 28 dB Harmonics (2nd and 3rd) 2fo, 3fo POUT = +20 dBm, 6 Mbps, 802.11a –45 dBm/MHz Delay and rise/fall time tDR, tDF 50% of VPA_EN edge and 90/10% of final output power level 400 ns Input return loss S11 @ TX port –12 dB Stability Stab 802.11n, MCS0, HT40, POUT = +20 dBm, 0.1 GHz to 20 GHz, load VSWR = 6:1 All non-harmonically related outputs < –43 dBm/MHz Ruggedness CW, PIN = 0 dBm, 0.1 GHz to 20 GHz, load VSWR = 10:1 No permanent damage or performance degradation Receive Characteristics Frequency range f 4900 5850 MHz Small signal gain S21 LNA enabled Bypass mode +12 –8 dB dB Noise figure NF 2.5 dB 3PrdP Order Input Intercept Point IIP3 LNA enabled Bypass mode +5 +20 dBm dBm Input return loss S11 LNA enabled Bypass mode –8 –8 dB dB Output return loss S22 –8 dB Enable time tEN 10% to 90% of receive RF power, from time that LNA_EN is at 50% 400 ns Power Detector Characteristics Frequency range f 4900 5850 MHz Power detector range, CW PDR Measured @ ANT pin 0 +23 dBm Output impedance PDZLOAD 2.2 kΩ Output voltage PDVNO_RF PDVP21 POUT = no RF, measured into 1 MΩ POUT = +21 dBm, CW, measured into 1 MΩ 0.2 0.9 V V Detector bandwidth PDBW 3.6 MHz TNote 1: Performance is guaranteed only under the conditions listed in this table.
PRELIMINARY DATA SHEET • SKY85717-21: FRONT-END MODULE Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 203068E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 18, 2014 5 Table 6. SKY85717-21 Electrical Specifications: Control Logic Characteristics (Note 1) (VCC = 5.0 V, PA_EN = 3.3 V, LNA_EN = CRX = 0 V, TA = 25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Control voltage: High Low VIH VIL 1.6 0 3.6 0.4 V V Input current, high IIH 120 μA Input current, low IIL 1 μA TNote 1: Performance is guaranteed only under the conditions listed in this table. Table 7. SKY85717-21 Control Logic Mode CRX (Pin 15) LNA_EN (Pin 16) (Note 1) PA_EN (Pin 6) (Note 2) VLIN (Pin 9) WLAN receive 1 1 0 0 WLAN receive bypass mode 1 0 0 0 WLAN transmit, high linearity mode 0 0 1 1 WLAN transmit, high efficiency mode 0 0 1 0 WLAN off 0 0 0 0 Note 1: LNA is on while LNA_EN is high. LNA is off and in bypass mode when LNA_EN is low. Note 2: PA_EN controls PA enable and transmit/receive switch logic.
PRELIMINARY DATA SHEET • SKY85717-21: FRONT-END MODULE Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 6 August 18, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203068E Evaluation Board Description The SKY85717-21 Evaluation Board is used to test the performance of the SKY85717-21 FEM. A suggested application schematic diagram is shown in Figure 3. A photograph of the Evaluation Board is shown in Figure 4. A Bill of Materials (BOM) for the Evaluation Board is provided in Table 8. Evaluation Board Test Procedures 1. Connect the system ground to connector J4, pin 2, of the Evaluation Board. 2. Apply 5 V to connector J4, pins 1 and 3. 3. Select a path to test according to the modes shown in Table 7. 4. Connect a multimeter or oscilloscope to connector J5, pin 12, to monitor the power detector voltage. 5. Apply an RF signal to connector J1 (ANT) to monitor the RX to ANT performance. Measure the response from the output of connector J2 (RX). 6. Apply an RF signal to connector J3 (TX) to monitor the ANT to TX performance. Monitor the output power on connector J1 (ANT). Care should be taken not to overdrive the amplifier by applying too much RF on the input to the device (–20 dBm provides a suitable starting input power for the device). 9BCircuit Design Considerations The following design considerations are general in nature and must be followed regardless of final use or configuration:  Paths to ground should be made as short as possible.  The RX and ANT ports are AC-coupled and do not require DC blocking capacitors. There are ESD diodes to ground and a DC blocking capacitor between the TX port (pin 8) and the die. Therefore, there is no DC present on this port.  If the TX port is connected to an external component with >3 VDC present on it, a 10 pF (component C8) general purpose blocking capacitor is recommended.  Capacitors C6 (1 μF) and C7 (100 pF) should be on the primary side of the Evaluation Board at a minimum manufacturable distance from the FEM.  Capacitor C20 (0.3 pF) needs to be as close as possible at manufacturable distance from the ANT pin of the IC, followed by L1 (1.0 nH) and C19 (0.3 pF), also at manufacturable distance from C20 and L1, respectively.  The ground pad of the SKY85717-21 has special electrical and thermal grounding requirements. This pad is the main thermal conduit for heat dissipation. Because the circuit board acts as the heat sink, it must shunt as much heat as possible from the device. Therefore, design the connection to the ground pad to dissipate the maximum wattage produced by the circuit board. Multiple vias to the grounding layer are required.  Evaluation Board trace losses are: RX = TX = 0.32 dB and ANT = 0.35 dB. NOTE: A poor connection between the ground pad and the ground increases the junction temperature (TJ), which reduces the life of the device. Package Dimensions The PCB layout footprint for the SKY85717-21 is shown in Figure 5. Typical part markings are shown in Figure 6. Package dimensions for the 16-pin QFN are shown in Figure 7, and tape and reel dimensions are provided in Figure 8.
PRELIMINARY DATA SHEET • SKY85717-21: FRONT-END MODULE Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 203068E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 18, 2014 7 VDDLENCRXTP2J541J5 J57105281163912VDDPENVDET1GNDRXGNDVDDVDETPA_ENGNDTXLNA_ENCRXGNDANTGNDVCC2VCC1VLIN234121110956781615 14 13C80 ΩC7100 pFC61 μFC31 μF25 ΩR80 ΩR7 VCC2VCC1TP1C41 μF528163741J4PAD17LENCRXVDDPENR426.1 KVDETSMAJ1SMAJ2SMAJ3Y0585L11.0 nH C200.3 pFC190.3 pF Figure 3. SKY85717-21 Application Schematic Y0461 Figure 4. SKY85717-21 Evaluation Board Assembly
PRELIMINARY DATA SHEET • SKY85717-21: FRONT-END MODULE Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 8 August 18, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203068E Table 8. SKY85717-21 Evaluation Board Bill of Materials (BOM) Reference Value Manufacturer Mfr Part Number Package Description R7 0 Ω Panasonic ERJ2GEJ0R0 0402 Thick film chip resistor L1 1.0 nH Murata LQG15HN1N0S02D 0402 High frequency multilayer R8 24.9 Ω Panasonic ERJ2RKF24R9 0402 Thick film chip resistor R4 26.1K Panasonic ERJ2RKF2612 0402 Thick film chip resistor C7 100 pF Murata GRM1555C1H101JZ01 0402 Multilayer ceramic C19, C20 0.3 pF Murata GJM1555C1HR30WB01 0402 RF, High Q, low loss C8, R3 0 Ω Panasonic ERJ2GE0R00 0402 Thick film chip resistor C3, C4, C6 1 uF TDK Corporation C1005X5R1A105K 0402 Multilayer ceramic
PRELIMINARY DATA SHEET • SKY85717-21: FRONT-END MODULE Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 203068E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 18, 2014 9 2.902X 0.405X ø0.2502X 0.402X 0.40002X 0.40002.900.20 Typ.0.20 Typ.0.45 Typ.0.45 Typ.Via Pattern(Note 4)Board MetalSolder Mask Pattern(Note 6)Stencil Pattern(Note 5)S2655Notes:1. All dimensions are in millimeters2. Dimensioning and tolerancing according to ASME Y14.5M-19943. Unless specified, dimensions are symmetrical about center lines.4. Via hole recommendations: 0.025 mm Cu via wall plating (minimum), soldermask on the far side should tent or plug via holes.5. Stencil recommendations: 0.10 mm stencil thickness, laser cut apertures, trapezoidal walls and rounded corners offer better paste release.6. Solder mask recommendations: contact board fabricator for recommended solder mask offset and tolerance.3.003.00 2.901.252.901.351.251.350.475 Typ.0.20 Typ.0.500 Typ.0.475 Typ.0.575 Typ.0.30 Typ.8XC0.050 X 45°0.20 Typ.0.500 Typ.0.500 Typ.1314151612341214121110956738131415161234121110956781314151612341211109567852% solder coverageon center padPackageOutline Figure 5. SKY85717-21 PCB Layout Footprint
PRELIMINARY DATA SHEET • SKY85717-21: FRONT-END MODULE Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 10 August 18, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203068E SKY2185717XXXXXPin1IndicatorSkyworksPart NumberLot NumberY0460 Figure 6. Typical Part Markings (Top View) Top View Side View Bottom ViewSee Detail A2.50 0.40 MaxExposed Pad1.35 ± 0.050.225 ± 0.0516X 0.30 Min8X 0.12 Min4X ø0.15, InternalSupport Only. Do NotSolder or Route UnderNotes:1. All measurements are in millimeters.2. Dimensions and tolerances according to ASME Y14.5M-1994.3. Unless otherwise specified the following values apply: Decimal Tolerance: Angular Tolerance: X.X (1 place) ± 0.1 mm ± 0.5° X.XX (2 places) ± 0.05 mm X.XXX (3 places) ± 0.025 mm4. Coplanarity applies to the terminals as well as all other bottom surface metallization.5. Dimension applies to metallized terminal. If terminal tip has a radius, dimension should not be measured in that radius area.6. Unless specified, dimensions are symmetrical about center lines.2.50Pin 1Indicator0.05 C0.05 C2X2X2X 0.0750.10 M C A BAB0.20 ± 0.05540.5000.05 CPin 1IndicatorO.30 x 45°8X 0.15CSeatingPlane1.35 ± 0.050.127 Ref0.02 + 0.03–0.020.05 C21XR0.075, TypDetail AScale 2X16 PlacesY1253 Figure 7. SKY85717-21 16-Pin QFN Package Dimensions
PRELIMINARY DATA SHEET • SKY85717-21: FRONT-END MODULE Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 203068E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 18, 2014 11 S2678a2.00 ± 0.05)(See Note 1)4.00 ± 0.1(See Note 2)2.75 ± 0.054.00 ± 0.10∅1.55 ± 0.05∅1.00 Min.8.00 + 0.30/– 0.103.50 ± 0.10(See Note 1)2.75 ± 0.051.75 ± 0.1Pin 1Indicator0.25 ± 0.050.70 ± 0.10AAAR0.1 Typ.Notes: 1. Measured from centerline of sprocket hole to centerline of pocket. 2. Cumulative tolerance of 10 sprocket holes: ±0.02 mm. 3. All measurements are in millimeters.CL Figure 8. SKY85717-21 Tape and Reel Dimensions
PRELIMINARY DATA SHEET • SKY85717-21: FRONT-END MODULE Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 12 August 18, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203068E 8BOrdering Information Model Name Manufacturing Part Number Evaluation Board Part Number SKY85717-21: 5 GHz, 802.11ac Front-End Module SKY85717-21 SKY85717-21-EVB Copyright © 2014 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.

Navigation menu