Araknis Networks AN500APIAC Araknis Networks 500-series Dual-Band Concurrent Wireless-AC Indoor Access Point User Manual

Araknis Networks Araknis Networks 500-series Dual-Band Concurrent Wireless-AC Indoor Access Point Users Manual

Users Manual

WIRELESS ACCESS POINTPRODUCT MANUALModels:AN-100-AP-I-NAN-300-AP-I-NAN-500-AP-I-ACAN-700-AP-I-AC
© 2016 Araknis Networks®2Araknis Networks Wireless Access PointProduct Manual About this Manual-Return to Table of Contents-1 - About this ManualThis manual was created to provide a reference for installers and end users of Araknis Networks™ products. It provides all known information regarding the installation, setup, use, and maintenance of the product. The symbols below are used to identify important information:Pro Tip – Pro tips are included in sections of the manual to add information that provides extra value, utility, or ease-of-use for the installer or end user of the product. Pro tips may also link to extra information that will provide a better understanding of application, technology or use of the product or feature in question. These items are not required, but have been added for your convenience.Note – Notes emphasize information important to the installation, setup, or use of the product that is not essential to follow for safety of the equipment or user. Notes may be located before or in the midst of the section to which they apply, depending on the type of information. These items usually contain essential information, like the size or dimension of a separate part required, or a critical step in the process, that, if missed, would cause the installer or end user extra work to overcome.Caution – The caution symbol is used to indicate information vital to the safety of the equipment in use with the product, or the product itself. Cautions are always provided before the information they relate to. Not following a caution will almost always result in permanent damage to equipment that is not covered by warranty.Warning – Warnings indicate information vital to the safety of the installer or end user of the product. Warnings are always provided before the information they relate to. Not following a warning may result in permanent damage to equipment and serious injury or death of the installer or end user.
© 2016 Araknis Networks®3Araknis Networks Wireless Access PointProduct Manual About this Manual-Return to Table of Contents-Table of Contents1 - About this Manual 22 - Welcome to Araknis Networks™ 62.1 - Features 62.2 - Package Contents 63 - Hardware Overview 73.1 - Top 73.2 - Bottom 73.3 - Side 74 - Mounting Location - General Guidelines 85 - Wiring Requirements 95.1 - Network Cable Requirements 95.2 - PoE Requirements 95.3 - Power Requirements for Non-PoE Application 95.4 - Wiring Instructions 95.4.1 - Wiring Diagram 106 - Mounting the Access Point 116.1 - Table Top/Shelf 116.2 - Junction Box Mounting 116.2.1 - Instructions 116.3 - Wall or Ceiling Drywall Mounting Instructions 126.4 - Ceiling Tile Mounting Instructions 127 - Power-On and Operation 137.1 - Status LED Operation 138 - Introduction to Network Setup 149 - Accessing the Web Interface 149.1 - EZ Access Method (Default) 159.2 - Configured System Name Access 169.3 - DHCP/Static IP Address Method 179.3.1 - Finding the IP Address of the Access Point 179.3.2 - Default IP Address Access 1810 - Web Interface Overview 2110.1 - Applying Changes in the Web Interface 2211 - Status Menu 2311.1 - System Status 2311.1.1 - System Information 2411.1.2 - Wireless Information 2511.1.3 - LAN Information 2611.1.4 - System Log 2711.1.4.1 - Using the System Log 27
© 2016 Araknis Networks®4Araknis Networks Wireless Access PointProduct Manual About this Manual-Return to Table of Contents-11.2 - Wireless interface 2811.2.1 - Radio Status 2911.2.2 - Utilization of SSID 3011.2.3 - Wireless Network 3011.2.4 - Connected Clients 3112 - Settings Menu 3212.1 - System Settings 3212.1.1 - System Information 3312.1.2 - Date and Time Settings 3412.1.3 - Time Zone 3512.2 - LAN Settings 3612.2.1 - IP Settings 3712.2.2 - Interface Settings 3812.3 - Wireless Settings 3912.3.1 - Radio Settings 4012.3.2 - Utilization of SSID 4112.3.3 - Wireless Networks 4212.3.4 - Wireless Security Menu 4312.3.4.1 - WPA-PSK Mixed and WPA2-PSK Modes 4312.3.4.2 - WPA and WPA2 Modes 4412.3.5 - Guest Network 4512.4 - Security Settings 4712.4.1 - User Accounts 4812.4.2 - Access Control 4912.4.3 - Email Alert 5012.4.4 - Device Discovery 5212.5 - Schedule 5312.5.1 - Auto Reboot Settings 5412.5.2 - Auto Ping Gateway Settings 5512.5.3 - Wi-Fi Scheduler 5613 - Maintenance 5813.1 - Ping Test 5813.2 - Traceroute Test 5913.3 - File Management 6013.3.1 - Configuration File 6113.3.1.1 - Backup Current Configuration 6113.3.1.2 - Upload New Configuration File 6113.3.1.3 - Restore Factory Defaults 6213.3.1.4 - Hardware Factory Default 6213.3.1.5 - Firmware 6313.4 - Restart 6413.5 - Logout 65
© 2016 Araknis Networks®5Araknis Networks Wireless Access PointProduct Manual About this Manual-Return to Table of Contents-14 - Advanced Menu 6614.1 - Advanced Wireless Settings 6614.1.1 - Radio Settings 6714.1.2 - Client Limit 6814.2 - Wireless MAC Filter Settings 6914.2.1 - MAC Filter Settings 6914.2.2 - MAC Filter List 7014.3 - WPS Settings 7114.3.1 - Configuring WPS Connections 7114.4 - Site Survey 7214.4.1 - Select Interface 7214.4.2 - Result 7314.5 - Spectrum Analyzer 7414.6 - Wireless Trac Shaping Settings 7514.7 - SNMP Settings 7614.7.1 - SNMPv2 Settings 7714.7.2 - SNMPv3 Settings 7814.8 - Spanning Tree Settings 7914.9 - VLAN Settings 8014.10 - Rogue AP Detection 8115 - Troubleshooting 8215.1 - Hardware Reset Procedure 8216 - Software Defaults 8316.1 - Basic Menus 8316.2 - Advanced Menus 8417 - Table of Figures 8518 - Specifications 8719 - CE Warning 9320 - AN-100-AP-I-N FCC Statement 9321 - AN-300-AP-I-N FCC Statement 9622 - AN-500/700-AP-I-N FCC Statement 10023 - 2-Year Limited Warranty 10424 - Contacting Technical Support 104
© 2016 Araknis Networks®6Araknis Networks Wireless Access PointProduct Manual Welcome to Araknis Networks™-Return to Table of Contents-2 - Welcome to Araknis Networks™Thank you for choosing an Araknis™ Wi-Fi access point. With sleek, unobtrusive housings, extensive features, unique easy setup, and convenient PoE power, these products are ideal for use in both residential and commercial applications.2.1 - FeaturesFeature AN-100-AP-I-N AN-300-AP-I-N AN-500-AP-I-N AN-700-AP-I-N2.4GHz Radio Yes Yes Yes Yes5GHz Radio No Yes No YesConcurrent Dual-band No Yes No YesGigabit Ethernet No Yes No YesPoE Standard 802.3af 802.3af/at 802.3af 802.3af/atWiFi Standard 802.11 b/g/n 802.11 a/b/g/n 802.11 b/g/n 802.11 a/b/g/nOvrC Enabled Yes Yes Yes Yes2.2 - Package Contents*Not Pictured: Wall Mount TemplateFigure 1. Package ContentsWAPLAN CableMounting Bracket Tile Ceiling Backing PlateTile Ceiling Mounting HardwareQuick Start GuideDrywall Mounting Hardware
© 2016 Araknis Networks®7Araknis Networks Wireless Access PointProduct Manual Hardware Overview-Return to Table of Contents-3 - Hardware OverviewUse these images to familiarize yourself with the physical layout of your access point.3.1 - TopStatus LEDReset ButtonAN-300-AP-I-NStatus LEDReset ButtonAN-100-AP-I-N3.2 - BottomRubber Feet (4)Power/Ethernet ConnectionsAN-300-AP-I-NAN-100-AP-I-NEthernet Cable Knockout3.3 - SideVentilation Holes
© 2016 Araknis Networks®8Araknis Networks Wireless Access PointProduct Manual Mounting Location - General Guidelines-Return to Table of Contents-4 - Mounting Location - General Guidelines• Locate the access point in a central location. Higher mounting can provide better coverage.• Avoid mounting near kitchens or rooms with large appliances that may give o EMI noise, which can reduce connection speed, and in extreme cases, block WiFi connectivity altogether.• As a rule of thumb, each access point can cover about a 300 ft (100m) radius (actual performance varies based on multiple variables). • Plan multiple access points at least 200 ft apart. Signal should overlap but only slightly.• Use network site survey tools (not included) to determine mounting locations if possible. This will ensure you get the best coverage and performance from your installation.Pro Tip – Professional site survey tools are available from vendors in the market such as Metageek and Fluke Networks.Figure 2. Residential Access Point LocationRouterKitchen Area(Weak signal due to interference)WAPStrong SignalWeak SignalFigure 3. Small Commercial Access Point LocationRouterMachine Area(Weak signal due to interference)WAP WAPStrong SignalWeak Signal
© 2016 Araknis Networks®9Araknis Networks Wireless Access PointProduct Manual Wiring Requirements-Return to Table of Contents-5 - Wiring RequirementsThe access point must be connected to the local network and powered using PoE (Power over Ethernet) or 12V DC power. Install the required cabling and equipment according to the guidelines in this section.5.1 - Network Cable Requirements568B termination is recommended (Figure 4. EIA/TIA 568B Termination Pattern) Connect a Cat5e/6 straight-through cable between the access point and a local area network port on a switch or router. Figure 4. EIA/TIA 568B Termination Pattern(Gold pins facing up)Pin 1 White/Orange Pin 5 White/BluePin 2 Orange Pin 6 GreenPin 3 White/Green Pin 7 White/BrownPin 4 Blue Pin 8 BrownNote – Maximum cable length is 328 feet (100m). A repeater device is required for longer runs.5.2 - PoE RequirementsCaution – Use an 802.3af/at compliant PoE injector, switch, or router to power the access point. Non-compliant devices can harm the access point and lead to unpredictable results.5.3 - Power Requirements for Non-PoE ApplicationIf PoE is not being used, connect a suitable power supply (not included) from a nearby outlet to the DC input of the access point.• AC Outlet – 100-240V AC, 50/60Hz (AN-100: 0.3A; AN-300: 0.6A)• DC Input – 12V DC 1A (AN-100); 2A (AN-300).5.4 - Wiring InstructionsPlan a mounting location and install the wiring before installing the access point.Warning – Do not connect any equipment to the wiring until every connection has been terminated and testing is complete.1. For PoE installations, install a network cable from the PoE device to the access point and terminate both ends to the same pattern. The DC power supply is not needed.2. For non-PoE installations, locate an outlet for the power supply.Pro Tip – If needed, extend a 2-conductor power wire from the power supply to the access point.
© 2016 Araknis Networks®10Araknis Networks Wireless Access PointProduct Manual Wiring Requirements-Return to Table of Contents-5.4.1 - Wiring DiagramFigure 5. Network Wiring DiagramMobile AppsENABLEDWeb Browser Access
© 2016 Araknis Networks®11Araknis Networks Wireless Access PointProduct Manual Mounting the Access Point-Return to Table of Contents-6 - Mounting the Access Point6.1 - Table Top/ShelfThe access point comes with rubber feet installed for placement on flat surfaces. The mounting bracket is not required for this application.6.2 - Junction Box MountingThe mounting bracket is compatible with most common junction box and plaster ring dimensions, including common ceiling box sizes:• Single/Double Gang• 4” Square Box• 3” Octagonal Box• 4” Octagonal Box6.2.1 - Instructions1. Place the mounting bracket over the junction box and attach it loosely with 2 screws. (two 6-32 x 1” screws are included) Use the hole pattern on the bracket that best matches the box pattern. See Figure 5A.2. Level or align the bracket with nearby objects for uniformity and tighten the screws enough to secure it. Avoid over-tightening and warping the bracket.3. Connect the wiring to the access point and push any extra wiring back into the opening. See Figure 5B.4. Snap the access point onto the bracket. See Figure 5C.Figure 6. Junction Box MountingFigure 6A Figure 6B Figure 6C
© 2016 Araknis Networks®12Araknis Networks Wireless Access PointProduct Manual Mounting the Access Point-Return to Table of Contents-6.3 - Wall or Ceiling Drywall Mounting Instructions1. Place the bracket over the desired mounting location with the arrow on the bracket pointing up for wall mounting. See Figure 6A.2. Mark the “C” or “D” slots on the mounting surface, then remove the bracket and thread one of the included drywall anchors into the center of each mark using a Phillips screwdriver.3. Level or align the bracket with nearby objects and fasten it to the anchors using the two included anchor screws. Tighten the screws enough to secure the bracket. Avoid over-tightening and warping the bracket.4. Connect the wiring to the access point and push any extra wiring back into the opening. See Figure 6B.5. Snap the access point onto the bracket. See Figure 6C.Figure 7. Drywall MountingFigure 7A Figure 7B Figure 7C6.4 - Ceiling Tile Mounting Instructions1. Place the bracket over the desired mounting location and align it with nearby objects for uniformity. 2. Mark the “C” or “D” slots on the ceiling tile (and the center hole if needed for wiring).3. Cut the opening with a keyhole saw. Use a drill to make clean holes for the mounting screws.4. Place the ceiling backing plate and nuts on top of the tile as shown and fasten the mounting bracket to the tile using the included screws.5. Connect the wiring to the access point and push any extra wiring back into the opening.6. Snap the access point onto the bracket.Figure 8. Ceiling Tile Mounting
© 2016 Araknis Networks®13Araknis Networks Wireless Access PointProduct Manual Power-On and Operation-Return to Table of Contents-7 - Power-On and OperationOnce the access point is powered, the status LED can be used to determine proper operation.Pro Tip – Check the wireless network connection status in your PC to see if the default SSID “araknis_initial” is being broadcast. If the SSID is being broadcast, you may continue to the next section to begin configuring device access and software setup.7.1 - Status LED OperationAfter installing the access point, connect the network and power cables and check the status LED. Once the LED remains illuminated (no more flashes), then the device is ready to be accessed for setup.Figure 9. Status LED LocationStatus LEDAN-300-AP-I-NStatus LEDAN-100-AP-I-NStatus LED• Blue LED:• Blinking: Device is not working correctly. Refer to the Troubleshooting section.• Solid: Device is operating correctly.
© 2016 Araknis Networks®14Araknis Networks Wireless Access PointProduct Manual Introduction to Network Setup-Return to Table of Contents-8 - Introduction to Network SetupThe access point setup menu is used to make network configuration changes. This section explains how to access and use the menu.Warning – All Araknis access points will transmit the same SSID, “araknis_initial” by default. If multiple access points are being installed in the same network, power on and complete network setup for one device at a time to avoid confusion about which access point you are connected to. Always change the SSID during initial setup.9 - Accessing the Web InterfaceThere are several ways to access the web interface of the access point:• EZ Access Method – Default method used for initial setup. Connect your computer to the access point using Wi-Fi.• Configured System Name Access – Enter the device name instead of the IP address to access the web interface.• DHCP/Static IP Address Method – Can be used any time. Connect your computer to the network wired or wirelessly and enter the IP address issued to the access point by the network, or the default IP address, (192.168.20.253).• OvrC Method – OvrC gives you remote device management, real-time notifications, and intuitive customer management, right from your computer or mobile device. Setup is plug-and-play, with no port forwarding or DDNS address required. To add this device to your OvrC account:1. Connect the WAP to the Internet2. Log Into OvrC (www.ovrc.com)3. Add the Device (MAC address and Service Tag numbers needed for authentication)
© 2016 Araknis Networks®15Araknis Networks Wireless Access PointProduct Manual Accessing the Web Interface-Return to Table of Contents-9.1 - EZ Access Method (Default)When the WAP is powered on for the first time, it transmits the default, unsecured SSID, “araknis_initial”. Connect and access the web interface without any cable connections or network card setting changes.Note – Make sure the WAP is connected to a network with a functioning DHCP server. After the WAP is powered on, startup usually takes two to four minutes to complete. Wait for the Status LED to turn solid before beginning setup. Figure 10. Default SSIDWAP set to DHCP by defaultNetworkPC set to DHCParaknis_initialOn your wireless network-enabled computer:1. Disconnect any network cables from your computer.2. Make sure the wireless network card is set to obtain an IP address automatically (DHCP mode).3. Connect your computer to the wireless network named “araknis_initial”.4. Open a web browser and enter the configuration address for your device:• AN-100-AP-I-N enter: http://config.an100.wap/• AN-300-AP-I-N enter: http://config.an300.wap/5. Enter the default login credentials:• Username: araknis• Password: araknisFigure 11. EZ Setup Login Screen
© 2016 Araknis Networks®16Araknis Networks Wireless Access PointProduct Manual Accessing the Web Interface-Return to Table of Contents-9.2 - Configured System Name AccessNote – “Araknis EZ Access” on page 52 must be enabled for this access method to work. The setting is enabled by default.1. See section “12.1 - System Settings” on page 32 to set the system name.2. Apply the settings. After configuration, the WAP web interface may be accessed using the system name.3. Open a web browser and enter the configuration address for your WAP in this format (Example System Name = smith100):• Enter into address bar: http://config.smith100.wap/4. Enter the login credentials. (Default: araknis/araknis)Figure 12. System Name Access
© 2016 Araknis Networks®17Araknis Networks Wireless Access PointProduct Manual Accessing the Web Interface-Return to Table of Contents-9.3 - DHCP/Static IP Address MethodConnect your computer to the network wired or wirelessly and enter the IP address issued to the access point by the network, or the default IP address, 192.168.20.253.Note – If the WAP is not issued a DHCP IP address on the network, access the device using the default IP address.9.3.1 - Finding the IP Address of the Access PointThe WAP is configured to DHCP by default so that the DHCP server can assign an IP address when the WAP is connected to the network (the DHCP server is usually the router). This address can be used for accessing the web interface.1. Use one of these methods to find the IP address of the WAP:• Check the client table on your router• Use a network scanner (e.g. Fing) to sni the network. The Araknis WAP manufacturer field will display Snap AV.• See the highlighted field in the figure below for an example of an Araknis device being identified.Figure 13. Fing IP Scanner Example2. Once the IP address is found, enter it in your web browser and log in. (Default: araknis/araknis)
© 2016 Araknis Networks®18Araknis Networks Wireless Access PointProduct Manual Accessing the Web Interface-Return to Table of Contents-9.3.2 - Default IP Address AccessAccess the interface using the default IP address, 192.168.20.253. Use this method if the access point is not issued an IP address on the network or if access is required while not connected to a network.1. Connect your PC to the WAP using a network patch cable.Computer WAP2. On your PC, open the Control Panel and left-click Network and Internet.3. Left-click Network and Sharing Center.4. In the left bar, left-click Change adapter settings.
© 2016 Araknis Networks®19Araknis Networks Wireless Access PointProduct Manual Accessing the Web Interface-Return to Table of Contents-5. Right-click the icon for the wired network connection and left-click Properties.6. Left-click to highlight Internet Protocol Version 4 (TCP/IPv4), then left-click Properties.7. In the General tab, left-click Use the following IP address: and enter the IP address and subnet mask.• IP Address: 192.168.20.2• Subnet Mask: 255.255.255.0
© 2016 Araknis Networks®20Araknis Networks Wireless Access PointProduct Manual Accessing the Web Interface-Return to Table of Contents-8. Left-click OK to close Internet Protocol Version 4 (TCP/IPv4) Properties, then left-click OK to close Wireless Network Connection Properties.9. Open a web browser and navigate to http://192.168.20.253/. Log in using the default credentials:• Username: araknis• Password: araknis
© 2016 Araknis Networks®21Araknis Networks Wireless Access PointProduct Manual Web Interface Overview-Return to Table of Contents-10 - Web Interface OverviewFigure 14. Web Interface LayoutABC• A - Main Navigation MenuUse the submenus under the Status, Settings, Maintenance, and Advanced headings to configure and maintain the access point. Click Apply Changes to review and apply changes made in menus.• B - Main WindowThe main window displays the currently selected submenu.• C - Top BarThe top bar displays the current connection status to the OvrC server, the current internally-set system time, and the current system uptime in DAYS:HOURS:MINUTES.
© 2016 Araknis Networks®22Araknis Networks Wireless Access PointProduct Manual Web Interface Overview-Return to Table of Contents-10.1 - Applying Changes in the Web Interface1. After making changes to settings on a menu page, left-click the Save button on the menu to hold the new settings in the Apply Changes field.2. After all desired changes have been made, left-click Apply Changes to review the new settings. Left-click Apply to make the changes or Revert to cancel the changes.Figure 15. Applying Changes
© 2016 Araknis Networks®23Araknis Networks Wireless Access PointProduct Manual Status Menu-Return to Table of Contents-11 - Status Menu11.1 - System StatusThe System Status screen provides a real-time summary of access point system information, and is the first screen that appears when you log into the access point web interface. Use the screen to verify settings and operation of your device.Note – The figures displayed use AN-300-AP-I-N screenshots. AN-100 interfaces will indicate settings and information only for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.Figure 16. System Status ScreenPath – Status, System
© 2016 Araknis Networks®24Araknis Networks Wireless Access PointProduct Manual Status Menu-Return to Table of Contents-11.1.1 - System InformationDisplays current information about the WAP’s system settings.Figure 17. System Information TablePath – Status, System, System InformationParameters – • System Name – Name assigned to the system. Used for configured name access.• Service Tag – Internal tracking number used to track every product sold by Araknis Networks.• Firmware Version – Current version of firmware running on the access point.• Management VLAN ID – VLAN that must be used to access the web interface.
© 2016 Araknis Networks®25Araknis Networks Wireless Access PointProduct Manual Status Menu-Return to Table of Contents-11.1.2 - Wireless InformationDisplays current information about the wireless radio channel(s) in use. Figure 18. Wireless InformationPath – Status, System, Wireless InformationParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• MAC Address – Media Access Control (MAC) address. The 2.4GHz and 5GHz channels each have individual MAC addresses.• Number of Networks – Number of active wireless networks (i.e. SSID’s) configured on the radio interface.• Number of Connected Clients – Number of currently connected wireless clients on all configured networks using the radio interface.• Operation Mode – Indicates that the device is set up as a Wi-Fi access point.• TX – Amount of data, in bytes, transmitted on the respective radio interface since the last power cycle.• RX – Amount of data, in bytes, received on the respective radio interface since the last power cycle.
© 2016 Araknis Networks®26Araknis Networks Wireless Access PointProduct Manual Status Menu-Return to Table of Contents-11.1.3 - LAN InformationDisplays current LAN connection parameters.Figure 19. LAN InformationPath – Status, System, LAN InformationParameters – • Speed – Indicates negotiated LAN speed between the access point and the wired network.• Duplex – Indicates the negotiated duplex setting between the access point and the wired network.• MAC address – The MAC address assigned to the access point network connection. This address may also be found on the acces point’s service tag.• TX – Amount of data, in bytes, transmitted over the wired network connection.• RX – Amount of data, in bytes, received from the wired network connection.• IP Address – Access point IP address issued by the network router.• Subnet Mask – Access point subnet mask.• Default Gateway – Network router IP address.• Primary DNS – Indicates the primary DNS for the AN-100/300.• Secondary DNS – Indicates the secondary DNS for the AN-100/300.
© 2016 Araknis Networks®27Araknis Networks Wireless Access PointProduct Manual Status Menu-Return to Table of Contents-11.1.4 - System LogRecords all activity within the access point. The table refreshes to show the most recent activity when the System Status Page is opened.Figure 20. System LogPath – Status, System, System LogParameters – • System Log – The System Log records changes to access point configuration, connections, security conditions, and more. The window will refresh with the most current activity when the System Status Page is opened.11.1.4.1 - Using the System Log• Save Log – Click to view the log as a text file or save the log for future reference.• Clear Log – Click to permanently delete to contents of the System Log.
© 2016 Araknis Networks®28Araknis Networks Wireless Access PointProduct Manual Status Menu-Return to Table of Contents-11.2 - Wireless interfaceProvides a detailed look at wireless settings and performance for radio status and settings, wireless network configuration and connected client status.Figure 21. Wireless Interface StatusPath – Status, Wireless interface
© 2016 Araknis Networks®29Araknis Networks Wireless Access PointProduct Manual Status Menu-Return to Table of Contents-11.2.1 - Radio StatusProvides a detailed look at radio settings and performance.Figure 22. Radio StatusPath – Status, Wireless interface, Radio StatusParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• Interface Status – Indicates whether the 2.4/5GHz wireless interface is enabled or disabled. • Operation Mode – Access Point is the only mode currently supported.• Wireless Mode – Indicates whether the wireless channel is in 802.11b/g/n or 802.11a/n mode.• Channel Bandwidth – Set the bandwidth of the operating channel to 20MHz or 40MHz.• Channel Selection – Select auto or manual channel selection mode of the wireless interface.• Operating Channel – Indicates the selected channel for the wireless interface.• Channel Frequency – Indicates the frequency of the selected channel.• TX – Amount of data, in bytes, transmitted on each radio interface. • RX – Amount of data, in bytes, received on each radio interface.
© 2016 Araknis Networks®30Araknis Networks Wireless Access PointProduct Manual Status Menu-Return to Table of Contents-11.2.2 - Utilization of SSIDDetails the use and availability of SSID’s configured in the WAP.Figure 23. Utilization of SSID StatusPath – Status, Wireless interface, Wireless NetworkParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• SSID’s Used – Number of SSID’s currently in use by devices connected to the access point.• SSID’s Available – Number of SSID’s11.2.3 - Wireless NetworkThe Wireless Network table provides a detailed look at wireless network settings.Figure 24. Wireless Network StatusPath – Status, Wireless interface, Wireless NetworkParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• Wireless Network (SSID) – Network names (SSID’s) being transmitted by the access point.• Enabled – Indicates whether the wireless network is enabled or disabled.• Interface – Indicates the operating frequency of the wireless network.• Security – Indicates the security mode selected for the wireless network.• VLAN ID – Indicates the VLAN ID for the wireless network.• MAC address – MAC address of the wireless channel used by the network.• Broadcast SSID – Indicates whether the SSID is visible to Wi-Fi devices and discovery tools.• Channel Isolation – Indicates whether access point client devices connected to dierent SSID’s can communicate with each other.
© 2016 Araknis Networks®31Araknis Networks Wireless Access PointProduct Manual Status Menu-Return to Table of Contents-11.2.4 - Connected ClientsThe Connected Clients table provides a detailed look at connected wireless clients. All devices connected to any SSID on the access point will be displayed in the list.Figure 25. Connected Client StatusPath – Status, Wireless interface, Connected ClientsParameters – • Wireless Network (SSID) – Indicates the SSID being used by a connected wireless client.• Interface – Indicates the channel frequency of a connected wireless client.• MAC address – Indicates the MAC address of a connected wireless client.• TX (KBytes) – Amount of data, in kilobytes, transmitted to a connected wireless client.• RX (KBytes) – Amount of data, in kilobytes, received from a connected wireless client.• RSSI (dBm) – Indicates the wireless signal strength between the access point and the connected client. The color of the table field indicates signal quality: green=strong, yellow=medium, and red=weak.• Release – Click the Yes button to drop a client from the network.Pro Tip – The closer RSSI (dBm) value is to 0, the stronger the signal is, and the closer to -100, the weaker the signal is.
© 2016 Araknis Networks®32Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12 - Settings Menu12.1 - System SettingsThe System Settings screen allows configuration of basic system settings.Figure 26. System SettingsPath – Settings, System
© 2016 Araknis Networks®33Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.1.1 - System InformationThe System Information screen allows configuration of admin and access settings.Figure 27. System InformationPath – Settings, System, System InformationParameters – • System Name – Enter a meaningful name such as SmithHome or SmithBasement. Limited to 32 characters, including spaces. Can be used for system name access. See section “9.2 - Configured System Name Access” on page 16. • Admin Username – Enter a username for logging into the access point. Use letters, numbers, or punctuation. Limited to 32 characters, including spaces.Default: araknis• Admin Current Password – Enter the current login password when changing the password.Default: araknis• Admin New Password – Enter a new login password. Use letters, numbers, or punctuation. Limited to 32 characters, including spaces.• Confirm Admin New Password – Confirm a new login password (enter same password as above).• System LED – Turn the Status LED ON or OFF.Default: ON• Management VLAN – The VLAN ID from where the WAP web interface must be accessed. If Management VLAN=10, your computer must also be on VLAN 10.Default: UntaggedCaution – Changing the management VLAN may cause a loss of access to the web interface. Move the computer to the new management VLAN or reset the WAP to regain connectivity (see section “13.3.1.4 - Hardware Factory Default” on page 62).• Country – Select the country of the install location to comply with local standards.Default: United StatesConfiguration Instructions – 1. Click Settings, System.2. Specify the system information settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®34Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.1.2 - Date and Time SettingsThe Date and Time menu allows configuration of the ‘real world’ time setting and how it is kept correct for all access point functions.Figure 28. Date and Time SettingsPath – Settings, System, Date and Time SettingsParameters – • Manually Set Date and Time – Select to manually set date and time.• Date – Enter the year, month and date (four digits for year; two digits for month, two digits for date)• Time – Enter the hour and minutes for the correct current time. Use a mobile device or satellite clock for accuracy.• Synchronize with PC – Click this button to automatically sync the access point to a connected computer.• Automatically Get Date and Time – Select to automatically get date and time from various web resources.• NTP Server – Select an NTP (Network Time Protocol) Server to set reference standard date and time. Default: time.nist.gov.Configuration Instructions – 1. Click Settings, System.2. Specify the date and time settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®35Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.1.3 - Time ZoneThe menu allows configuration of time zone settings.Figure 29. Time ZonePath – Settings, System, Time ZoneParameters – • Time Zone – Select the appropriate time zone from the drop-down.• Enable Daylight Saving – Select to enable. DST start/end can change from year to year. Be sure to update this information.• Start – Select the month, date, day and time Daylight Saving Time starts from the dropdowns.• End – Select the month, date, day and time Daylight Saving Time ends from the dropdowns.Configuration Instructions – 1. Click Settings, System.2. Specify the time zone and DST settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®36Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.2 - LAN SettingsThe LAN Settings screen allows configuration of the access point LAN connection to the network router. In default mode, the IP Settings screen will show the DHCP IP address and default subnet mask. A static IP address, subnet mask, default gateway and DNS settings can be configured by disabling DHCP. LAN speed can also be configured in the Interface Settings menu.Figure 30. LAN SettingsPath – Settings, LAN
© 2016 Araknis Networks®37Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.2.1 - IP SettingsThe IP Settings menu is used to configure access point IP address settings. In default mode, the IP Settings screen will show the DHCP IP address and default subnet mask.Figure 31. IP SettingsNote – By default, DHCP is enabled. DHCP is set to be disabled in this image to illustrate all the available options in the menu.Path – Settings, LAN, IP SettingsParameters – Note – DHCP is the default setting. If a static IP address has been assigned, but DHCP is selected, the assigned IP address and subnet mask will be grayed out. To confirm the WAP IP address, see: System Status screen/LAN Information/IP address.• IP Address – Uncheck DHCP Enable to enter a static IP address for the AN-100/300. A static IP address is recommended.Warning – Be sure to use an IP address that is outside the DHCP server range to avoid duplicate addresses in the network.• Subnet Mask – Enter the subnet mask for the AN-100/300.Default: 255.255.255.0• Default Gateway – With DHCP disabled, enter the default gateway for the access point (network router IP address).• Primary DNS – With DHCP disabled, enter the primary DNS for the AN-100/300. This will typically be the network router IP address.• Secondary DNS – With DHCP disabled, enter the secondary DNS for the AN-100/300. This will typically be the network router IP address.Note – Both primary and secondary addresses are required if a static IP address is assigned.• DHCP – Allows the access point to receive a DHCP IP address from the network router if DHCP is enabled. Un-check the box to configure a static IP address (recommended).Default: Enabled
© 2016 Araknis Networks®38Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-Configuration Instructions – 1. Click Settings, LAN.2. Specify the IP settings.3. Click Save, then click Apply Changes to enable the new settings.12.2.2 - Interface SettingsThe Interface Settings menu is used to configure LAN speed and duplex settings.Figure 32. Interface SettingsPath – Settings, LAN, Interface SettingsParameters – • Speed – Select LAN speed from Auto, 1Gbps (300 Series only), 100Mbps, 10Mbps, Disable (turns the LAN Port OFF) Default: Auto• Duplex – (10/100Mbps modes only) Select the duplex setting between the access point and the network router from Half or Full.Default: FullConfiguration Instructions – 1. Click Settings, LAN.2. Specify the interface settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®39Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.3 - Wireless SettingsThe Wireless Settings screen allows configuration of the access point’s wireless settings and connections including 2.4GHz and 5GHz Radio settings, setup and configuration of wireless networks (SSID’s) and all required wireless modes, channels, security settings and, guest network configuration.Figure 33. Wireless Settings (AN-300-AP-I-N interface shown)Path – Settings, Wireless
© 2016 Araknis Networks®40Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.3.1 - Radio SettingsThe Radio Settings screen allows configuration of the access point’s radio settings including wireless modes, operating channels, channel bandwidth, and extension channel.Figure 34. Radio SettingsPath – Settings, Wireless, Radio SettingsParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• Enable Interface – Enable or disable the radio interface.Default: Yes. • Wireless Mode – Select the wireless mode for the radio. OPTIONS: 2.4GHz: 802.11b/g/n, 802.11b/g, 802.11b, 802.11g, 802.11n; 5GHz: 802.11a/n; 802.11a; 802.11n. Default: 2.4GHz - 802.11b/g/n; 5GHz - 802.11a/n.• Operating Channel – Select the desired Wi-Fi channel. Use a dierent channel than other APs on the network. On the 2.4GHz radio there are only three non-overlapping channels: 1, 6 and 11. Select a channel as far away from close-numbered channels as possible.Default: Auto.Pro Tip – In a multi-WAP environment, put adjacent WAPs on channels as far apart as possible. A spectrum analyzer tool (such as Metageek’s Chanalyzer Pro) is recommended for ultimate insight into the network setup.• Channel Bandwidth – Select 20/40MHz for auto select; Select 20MHz for better performance as needed; select 40MHz for greater speed as needed. This option is only available in 802.11n modes. Default: 2.4GHz - 20MHz; 5GHz - 40MHz.• Extension Channel – Only available when Wireless Mode is set to an 802.11n mode and channel Bandwidth is set to 20/40MHz or 40MHz. Extends the 20MHz channel to an Upper or Lower channel to achieve 40MHz bandwidth.Default: 2.4GHz - Upper Channel; 5GHz - Lower Channel.Pro Tip – The access point features a Site Survey tool that shows all 2.4GHz/5GHz networks and settings. Use the tool to scan the wireless neighborhood and find the channel with the least amount of interference and the extension channel with less trac from other wireless devices.Enter xref in Extension channel
© 2016 Araknis Networks®41Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-Configuration Instructions – 1. Click Settings, Wireless.2. Specify the radio settings.3. Click Save, then click Apply Changes to enable the new settings.12.3.2 - Utilization of SSIDDetails the use and availability of SSID’s configured in the WAP.Figure 35. Utilization of SSID StatusPath – Status, Wireless interface, Wireless NetworkParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• SSID’s Used – Number of SSID’s currently in use by devices connected to the access point.• SSID’s Available – Number of SSID’s
© 2016 Araknis Networks®42Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.3.3 - Wireless NetworksThe Wireless Networks menu allows configuration of access point wireless networks (SSID’s), security settings, band steering and channel isolation.Note – Be sure to change the SSID. The default settings are not secure.Figure 36. Wireless NetworksPath – Settings, Wireless, Wireless Settings, Wireless NetworksParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• Enable – Select Yes to turn a wireless network ON. Default: Yes (Checked)• Name (SSID) – Enter the network name for the network being configured.Default: araknis_initial; (Blank when adding a new network).Note – Be sure to change the SSID. The default settings are not secure.• Interface – Select 2.4GHz/5GHz or Both Channel Frequency.Default: Both, (2.4GHz when adding a network).• Security Mode – Configure the security mode for each wireless network. Select a security mode from the drop-down to open the Wireless Security Setup Window (“Figure 37. Wireless Security – WPA-PSK and WPA2-PSK Modes” on page 43).• Band Steering – (AN-300-AP-I-N only) Band steering uses both signal quality and throughput relative to the client device to determine whether the client should communicate on the 2.4- or 5GHz band. This optimizes signal strength to the device.Default: Disabled (Unchecked)• Broadcast SSID – Select whether or not to publicly display the SSID to nearby Wi-Fi devices.Default: Yes• Channel Isolation – Select to prevent communication between wireless clients on dierent SSID’s. Default: Not selected.• Add – Click to add a wireless network.• Delete – Click to delete a wireless network.
© 2016 Araknis Networks®43Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.3.4 - Wireless Security MenuThe Wireless Security menu opens during the setup of an existing or new wireless network.12.3.4.1 - WPA-PSK Mixed and WPA2-PSK ModesFigure 37. Wireless Security – WPA-PSK and WPA2-PSK ModesPath – Settings, Wireless, Wireless Networks, Security ModeParameters – • Name (SSID) – The name of the network being configured.• Security Mode – Select a mode from the drop-down. Use the same mode as the network router and other APs on the network. Selecting a non-PSK mode will cause the menu options to change.• Encryption – WPA2-PSK: AES; WPA2-PSK Mixed: Both (TKIP+AES).• Passphrase – Enter the appropriate passphrase for the wireless network being configured. If using the ASCII format, the password must be 8-63 characters in length. If using HEX, the password must be 64 HEX characters in length.Default: Blank• Group Key Update Interval – Enter a value to specify how often in seconds the Group key changes. RANGE: 30-3600 seconds.Default: 3600 (60 minutes)• Save – Click to save changes to the Wireless Security Settings for this network. The window will close.• Cancel – Click to cancel changes to the Wireless Security Settings for this network. The window will close.
© 2016 Araknis Networks®44Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.3.4.2 - WPA and WPA2 ModesFigure 38. Wireless Security – WPA-PSK and WPA2-PSK Modes• Name (SSID) – The name of the network being configured.• Security Mode – Select a mode from the drop-down. Use the same mode as the network router and other APs on the network. Selecting a PSK mode will cause the menu options to change.• Encryption – Cannot be modified. WPA2: AES; WPA Mixed: Both (TKIP+AES).• Group Key Update Interval – Enter how often the Group Key changes (from 30-3600 seconds).Default: 3600 (60 minutes)• Radius Server – Enter the Radius Server IP address.Default: Blank• Radius Port – Enter the Radius Server connection port number. Default: 1812 (This is a dedicated TCP/UDP port and typically should not be changed.)• Radius Secret – Enter the Radius Server connection secret.Default: Blank• Radius Accounting – Enable or disable Radius Accounting.Default: Disable• Radius Accounting Server – Enter the Radius Accounting Server IP address.Default: Blank• Radius Accounting Port – Enter the Radius Accounting Server connection port number.Default: 1813 (This is a dedicated TCP/UDP port and typically should not be changed.)• Radius Accounting Secret – Enter the Radius Accounting Server connection secret.Default: Blank• Interim Accounting Interval – Enter a value for how often accounting data will be sent, in seconds. RANGE: 60-600 seconds. Default: 600 (10 minutes)• Save – Click to save changes. The window will close.• Cancel – Click to cancel changes. The window will close.
© 2016 Araknis Networks®45Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.3.5 - Guest NetworkUse the Guest Network menu to configure guest networks. These optional networks are useful for allowing access to temporary users and controlling what parts of the network they can access.Figure 39. Guest NetworkPath – Settings, Wireless, Guest NetworkParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• Enable – Select to create a guest network. This will allow guests to log in to the wireless system without having to compromise network security by giving guests the password to the home network. There are separate 2.4GHz and 5GHz Guest Networks. If the guest is using an 802.11b/g device, (2.4GHz) they will only need the password to the 2.4GHz Network. If the guest is using an 802.11a/n device (5GHz) they will need the password to the 5GHz Network, and if the guest is using a device that can connect on both 2.4GHz and 5GHz, (iOS devices) they should have both. Default: Not Selected.• Name (SSID) – Enter an SSID for the guest network. Default: Araknis-2.4_GuestNetwork; Araknis-5.0_GuestNetwork• Edit – Click the Edit button to open the Guest Network Security Setup Window.Note – Guest networks are limited to Open, WPA-PSK Mixed and WPA2-PSK encryption modes. See section “12.3.4.1 - WPA-PSK Mixed and WPA2-PSK Modes” on page 43 for encryption setup instructions.• Security Mode – This indicates the Security Mode and Encryption selected in the Edit Mode, previous. Default: None• Broadcast SSID – Selecting this option will allow the guest network SSID to appear in ‘Network Lists’ on wireless devices for user login. If not selected, the user will have to know the SSID and enter it manually to access the network.
© 2016 Araknis Networks®46Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-Default: Un-selected. • Channel Isolation – Select to prevent communication between wireless clients on dierent SSID’s of the guest network. Default: Selected.• Manual IP Settings – Use the access point’s defaults or manually enter IP address settings.• Gateway IP Address – Enter the access point’s Guest Network Gateway IP address. Default: 192.168.200.1• Subnet Mask – Enter the subnet mask for the access point’s Guest Network Gateway.Default: 255.255.255.0• Automatic DHCP Server Settings• Starting IP Address – Enter the lowest address available for the Guest Network.Default: 192.168.200.100• Ending IP Address – Enter the highest address available for the Guest Network.Default: 192.168.200.200• WINS Server IP – Enter the IP address for the WINS Server for the Guest Network.Default: 0.0.0.0
© 2016 Araknis Networks®47Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.4 - Security SettingsThe Security Settings screen allows configuration of who can log into the access point interface and what level of privileges they have, how the device can be accessed, email notification of system status and warnings, and device discovery. Figure 40. Security SettingsPath – Settings, Security
© 2016 Araknis Networks®48Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.4.1 - User AccountsThe User Accounts menu allows configuration of who can log into the access point and what level of privileges they have. Figure 41. User AccountsPath – Settings, Security, User AccountsParameters – • Select – Select to allow editing of the selected table entry. Default: Not selected• Username – Click the Edit button to access the settings on a selected User Account. Enter a new username for logging into the access point. Use letters, numbers, or punctuation. Limited to 32 characters, including spaces.Default: araknis (Blank when adding a new account)• Privilege Level – Indicates the level of device management for the logged in user. OPTIONS: admin, Status, Status+Settings.Default: admin Status+Settings when adding a new account)• Password – Enter a new login password. Use letters, numbers, or punctuation. Limited to 32 characters, including spaces.Default: araknis (Blank when adding a new account)• Confirm Password – Confirm a new login password (enter same password as above).Default: araknis (Blank when adding a new account)• Delete – Click the icon to delete a specific user account.• Add – Click to add a new user account.• Edit – Click the Select arrow in the left column of a user account and click Edit to modify the account.Configuration Instructions – 1. Click Settings, Security.2. Specify the user account settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®49Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.4.2 - Access ControlThe Access Control menu allows configuration of how the access point can be accessed. Figure 42. Access ControlPath – Settings, Security, Access ControlParameters – • HTTP Port – Enter device web server port to connect. Default: 80Pro Tip – Assign a unique port number to enable remote access to the access point web interface via port forwarding on the network router.• Web Access – Select Enable or Disable to enable or disable the ability to modify the device via Web Browser. Default: EnableCaution – Disabling web access will cause a loss of connection to the web interface. If this occurs, regain connectivity by restoring the hardware to factory default settings. (Press Reset button for 10 seconds.)• Telnet – Enable or Disable the ability to modify the device via a command line interface (CLI) through a telnet session. Default: Enable• SSH – Enable or Disable the ability to modify the device via a command line interface (CLI) with a secure channel. Default: DisableConfiguration Instructions – 1. Click Settings, Security.2. Specify the access control settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®50Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.4.3 - Email AlertThe Email Alert menu allows configuration of the email notification system for status and warnings. Figure 43. Email Alert Setup ExamplePath – Settings, Security, Email AlertsParameters – • Status – Select Enable to send email notifications in the event of certain abnormal conditions.Default: Not selected• From – Enter the email address of the sender. Default: Blank• To – Enter the email address of the recipient. Default: Blank• Subject – Information regarding the nature of the system condition. Default: [Email-Alert][araknis][88:DC:96:1D:33:6B][Configuration Changed]• Email Account – • Username – Enter the username for the email account (Outlook, Gmail, etc.) sending the alert. Default: Blank• Password – Enter the password for the email account (Outlook, Gmail, etc.) sending the alert.Default: Blank• SMTP Server – Enter the SMTP Server and Port Number of the email client sending emails.Default: SMTP Server Blank; Port: 25• Security Mode – Select a security mode for sending Email Alerts. None, SSL/TLS, STARTTLS Default: None• Send Test Email – Click the button to send a test email to confirm Email Alert settings.
© 2016 Araknis Networks®51Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-Figure 44. Common Email Client PortsEmail Client Ports(TLS) Ports(SSL)Gmail 587 465Outlook 25 or 587 -Microsoft Exchange 25 465Yahoo - 465Oce 365 587 -Configuration Instructions – 1. Click Settings, Security.2. Specify the email alert settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®52Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.4.4 - Device DiscoveryThe Device Discovery menu allows configuration of how or if the access point can search for and connect to network devices via Bonjour and UPnP. Figure 45. Device DiscoveryPath – Settings, Security, Device DiscoveryParameters – • Bonjour – Enable to allow the access point to search for and connect to network devices running Apple iOS and OS X. Bonjour can also be run on devices running a Microsoft OS. Default: Disable • UPnP – Enable to allow the access point to search for and connect to network devices via UPnP Protocol (Universal Plug and Play). Default: Disable• Araknis EZ Access – Use a URL to access the web interface (see section “9.2 - Configured System Name Access” on page 16).Default: EnableCaution – If VLANs are enabled, this setting will automatically become disabled. In order for VLANs to work correctly, it must remain disabled and will require you to use the local IP address of the WAP in order to gain access to the GUI.Configuration Instructions – 1. Click Settings, Security.2. Specify the device discovery settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®53Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.5 - ScheduleUse the schedule settings menu to configure automated features including auto reboot, auto ping, and Wi-Fi access schedules for dierent SSID’s.Figure 46. Schedule Settings MenuPath – Settings, Schedule
© 2016 Araknis Networks®54Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.5.1 - Auto Reboot SettingsThe WAP can be set to reboot at specified times on a daily or weekly schedule. Rebooting the WAP will help ensure the best network performance by keeping the system memory clear and ending unnecessary connections.Figure 47. Auto Reboot SettingsPath – Settings, Schedule, Auto Reboot SettingsParameters – • Status – Enable or Disable Auto Reboot.Default: Disable• Date – Check the boxes for the WAP should reboot on.• Time – Enter the time for the reboot to take place in 24 hour format. (00:00=midnight; subtract 12 hours from 24 hour time for standard time 17:00-12:00=5:00pm)Configuration Instructions – 1. Click Settings, Schedule.2. Enable Auto Reboot.3. Set the desired days and time for reboots to occur.4. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®55Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.5.2 - Auto Ping Gateway SettingsUse auto ping to help ensure the WAP maintains network connectivity. Configure the WAP to ping the gateway, and if the ping results fall outside the desired settings, reboot the systemFigure 48. Auto Reboot SettingsPath – Settings, Schedule, Auto Reboot SettingsParameters – • Status – Enable or Disable Auto Reboot.Default: Disable• Date – Check the boxes for the WAP should reboot on.• Time – Enter the time for the reboot to take place in 24 hour format. (00:00=midnight; subtract 12 hours from 24 hour time for standard time 17:00-12:00=5:00pm)Pro Tip – Set the WAP to reboot when there are few or no users connected. This will ensure that users have the best experience when connected to the WAP.Configuration Instructions – 1. Enable Auto Reboot.2. Set the desired days and time for reboots to occur.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®56Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-12.5.3 - Wi-Fi SchedulerThe Wi-Fi Scheduler is used to configure when wireless networks are available for use. The scheduler is based on a 24-hour clock (00:00 = 12:00AM, the start of a given day).Figure 49. Wi-Fi SchedulerPath – Settings, System, Wi-Fi SchedulerParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• Status – Enable or Disable the Wi-Fi Scheduler.Default: Disable• Wireless Radio – Select 2.4GHz or 5GHz for the channel frequency to be scheduled.Default: 2.4GHz.• SSID Selection – Select the SSID to be scheduled.• Schedule Templates – Create dierent Wi-Fi schedules using templates as detailed below:• Choose a Template – Select the template that matches the schedule requirements.• Always Available – 00:00-24:00. The wireless network is always ON.• Available 8-17 Daily – 08:00-17:00. The wireless network is ON at 8:00AM and OFF at 5:00PM.• Available 8-17 Daily Except Weekends – 08:00-17:00. The wireless network is ON at 8:00AM and OFF at 5:00PM Monday-Friday and always OFF on Saturday and Sunday.• Custom Schedule – Allows custom configuration of the wireless network ON/OFF schedule based upon user requirements.• Schedule Table – Modify template schedules or make custom schedules. See the configuration instructions for setup.• Day – Day of the week being configured.• Availability – Select whether the device is Available for the set duration, or Unavailable for the specified day.• Duration – Time setting from start to finish for availability in 24 hour format. 00:00=midnight; subtract 12 hours from 24 hour time for standard time 17:00-12:00=5:00pm;)
© 2016 Araknis Networks®57Araknis Networks Wireless Access PointProduct Manual Settings Menu-Return to Table of Contents-Configuration Instructions – Application example: The 2.4GHz SSID, “Market 2”, needs to be made available during the hours of 8AM to 6PM Monday through Friday, 10AM to 5PM on Saturdays, and unavailable the rest of the week.Figure 50. Wi-Fi Scheduler Menu1. Enable the Wi-Fi Scheduler feature.2. Select the wireless frequency and SSID for scheduling. In our example, we will select 2.4GHz frequency, and the SSID, Market 2.3. Select an option from the Schedule Templates dropdown to use. In our example, we will select Available 8-17 Daily, since this template is closest to the schedule needed.4. Change the Schedule Table to work on the desired schedule. In our example, we will make the following changes:• Sunday: Set to Unavailable so that no access is available the entire day.• Monday-Friday: Set to Available and enter a duration of 08:00 - 18:00 (8AM-6PM)• Saturday: Set to Available and enter a duration of 10:00 - 17:00 (10AM-5PM)5. Click Save at the bottom of the System Information screen. Click Apply Changes to enable the new schedule. The figure below shows the configured and applied settings.Figure 51. Wi-Fi Scheduler Setup Complete
© 2016 Araknis Networks®58Araknis Networks Wireless Access PointProduct Manual Maintenance-Return to Table of Contents-13 - Maintenance13.1 - Ping TestThe Ping Test screen can be used to determine if a particular IP address can be reached across an IP network.Figure 52. Ping TestPath – Maintenance, PingParameters – • Target IP / Domain Name – Enter the IP address of a device or web page to determine if it can be reached.• Ping Packet Size – Enter the packet size of each ping. Maximum size: 65535.Default: 64 Bytes• Number of Pings – Enter the number of ping attempts. Default: 4• Start – Click the Start button to send the Ping. Ping Test results will be displayed in the text frame. Ideal results: Same number of packets transmitted/received, 0% packet loss.Configuration Instructions – 1. Click Maintenance, Ping.2. Specify the ping test settings.3. Click Start.
© 2016 Araknis Networks®59Araknis Networks Wireless Access PointProduct Manual Maintenance-Return to Table of Contents-13.2 - Traceroute TestThe Traceroute Test screen can be used to display the route and delays for data packets to/from a destination on an IP network. Figure 53. Traceroute Test Path – Maintenance, TracerouteParameters – • Target IP / Domain Name – Enter the IP address of a device or web page to show the path of communication to that device or website.• Start – Click the Start button to start Traceroute. Traceroute Test results will be displayed in the text frame.• Stop – Click the Stop button to stop Traceroute.Configuration Instructions – 1. Click Maintenance, Traceroute.2. Specify the traceroute test settings.3. Click Start.4. Click Stop to end the test.
© 2016 Araknis Networks®60Araknis Networks Wireless Access PointProduct Manual Maintenance-Return to Table of Contents-13.3 - File ManagementUse the File Management screen to back up or restore settings and apply firmware updates.Figure 54. File ManagementPath – Maintenance, File Management
© 2016 Araknis Networks®61Araknis Networks Wireless Access PointProduct Manual Maintenance-Return to Table of Contents-13.3.1 - Configuration FileUse the Configuration File menu to back up or restore settings to the access point.Figure 55. Configuration FilePath – Maintenance, File Management, Configuration File13.3.1.1 - Backup Current ConfigurationSave the access point’s current configuration settings to a “.tar” format compressed archive on your computer.1. Click the To PC button and select a location to save the file.2. Name the file and save it to your computer.13.3.1.2 - Upload New Configuration FileRestore previously saved configuration settings to the access point to restore settings.1. Click the Choose File button and select a configuration file (“.tar” file type) from the Open window.2. The file name will appear to the right of the Choose File button as shown in Figure 56. Uploading a New Configuration File, below.3. Click the From PC button to upload the configuration file. Wait while the Rebooting screen opens and loads the selected configuration. When the upload is finished, the Authentication Required (Log In) window will open.4. Log in and confirm Configuration settings.Figure 56. Uploading a New Configuration File
© 2016 Araknis Networks®62Araknis Networks Wireless Access PointProduct Manual Maintenance-Return to Table of Contents-13.3.1.3 - Restore Factory DefaultsUse the File Management screen to restore default settings.Note – When restoring factory defaults, the SSID, IP address, subnet mask, and gateway IP address will also be reset. Reconnect to the access point using the instructions beginning in section “9.1 - EZ Access Method (Default)” on page 15.Figure 57. Restore Factory DefaultsPath – Maintenance, File Management, Configuration File, Restore Factory DefaultsNote – All current settings will be permanently lost if not backed up. See Backup Current Configuration, above, to backup current settings prior to executing Restore to Factory Defaults.Configuration Instructions – 1. Click the Yes button to restore the access point to factory default settings. The red ALERT message will appear.2. Click Confirm to restore factory defaults. Wait while the rebooting screen is open and loading the selected configuration. When the configuration upload is finished, the login window will appear.3. Enter the username and password. (araknis; araknis)4. Confirm the new configuration settings.13.3.1.4 - Hardware Factory DefaultIf restoring factory defaults does not restore proper functionality to the AN-100/300, a hardware reset may be performed to reload the original base configuration file (saved in the access point’s memory).Configuration Instructions – 1. Using a paper clip or other small, blunt tool press the reset button located on the top of the access point for 30 seconds.2. After two to four minutes, the WAP will reboot. Restart the setup process or upload a previously saved configuration.
© 2016 Araknis Networks®63Araknis Networks Wireless Access PointProduct Manual Maintenance-Return to Table of Contents-13.3.1.5 - FirmwareUse the Firmware menu to upload new firmware to the AN-100/300.Figure 58. FirmwarePath – Maintenance, File Management, FirmwareParameters – • Current Firmware Version – Indicates the current running firmware version.• Date Activated – Date the current firmware was uploaded and activated.Configuration Instructions – 1. Click the Browse button to navigate to where the firmware file is saved.2. Select the file and then press Enter/Return on the computer keyboard or click Open on the Upload menu. (The firmware file name should appear next to the Upload New Firmware File Browse button.)3. Click Upload. The Upload Firmware Information screen will open.4. Click Upgrade. Wait while the new firmware loads. When the configuration upload is finished, the login screen will appear.5. Enter the username and password. 6. Confirm the firmware version.
© 2016 Araknis Networks®64Araknis Networks Wireless Access PointProduct Manual Maintenance-Return to Table of Contents-13.4 - RestartReboot the access point.Figure 59. RestartPath – Maintenance, RestartConfiguration Instructions – 1. Click the Reboot the Device button. The message, “This will reboot the device and may take a few seconds...” will appear. 2. Click OK to reboot (or Cancel to return to the Restart Screen).3. Wait while the access point reboots. When the device has rebooted, the login screen will appear.4. Enter the username and password.5. Confirm the firmware and configuration.
© 2016 Araknis Networks®65Araknis Networks Wireless Access PointProduct Manual Maintenance-Return to Table of Contents-13.5 - LogoutLogout can be used to change the user currently logged into setup. After working in the setup screens, a logged in user can simply close the browser tab or click Logout. Closing the browser tab will close the setup screen completely, Logout will end the session for the logged in user and open the Authentication Required (Log In) window. Figure 60. Logout AlertPath – Maintenance, LogoutConfiguration Instructions – 1. From any screen, click Logout in the system menu. The Logout ALERT will appear on screen.2. Click Cancel to return to the setup screen; click Confirm to log the current user out.
© 2016 Araknis Networks®66Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14 - Advanced MenuNote – Advanced menu settings should not require any changes for most applications.14.1 - Advanced Wireless SettingsThe Advanced Wireless Settings screen allows configuration of radio settings for unit of measure, data rate, power and RTS/CTS Threshold as well as a client limit by band, (2.4GHz/5GHz).Figure 61. Advanced Wireless SettingsPath – Advanced, Wireless Settings
© 2016 Araknis Networks®67Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.1.1 - Radio SettingsThe Advanced Wireless Settings menu allows configuration of radio settings for unit of measure, data rate, power and RTS/CTS Threshold.Figure 62. Radio SettingsPath – Advanced, Wireless Settings, Radio SettingsParameters – • Transmit Power Unit – Select the preferred unit of measure. OPTIONS: dBm, mW. Default: dBm.• Data Rate – Select a setting from the drop-down to set the available transmit data rate permitted for connected clients. A lower data rate reduces throughput, but increases the transmission range. OPTIONS: See drop-down list. Default: Auto.• Transmit Power – Select a setting from the drop-down to set the radio power. A higher gain will improve performance but can also cause interference with other access points in close range on the same channel. Also, a higher coverage range corresponds with lower throughput (i.e. to achieve the highest transmit power, the connection must run at the lowest data rate). Set this value as low as possible (for adequate coverage) to get the maximum wireless speed/data throughput. OPTIONS: See drop-down list. Default: Full 100% -29dBm.• RTS/CTS Threshold (Range: 1-2346) – Enter a value for the threshold package size for RTS/CTS (request to send/clear to send). A lower number increases the frequency that the packets are sent and consumes more bandwidth. RANGE: 1-2346. Default: 2346Configuration Instructions – 1. Click Advanced, Wireless Settings.2. Specify the radio settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®68Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.1.2 - Client LimitThe Advanced Wireless Settings screen allows configuration of client limit by band, (2.4GHz/5GHz).Figure 63. Client Limit SettingsPath – Advanced, Wireless Settings, Client LimitParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• Enable – Select to enable Client Limit, by channel. Default: Not Selected.• Max Client No. – Set the maximum number of clients that can be connected to a channel at a given time. (For AN-300, the maximum number of clients is for each radio interface.) RANGE: 1-127. Default: 127.Pro Tip – It is recommended to design the wireless network so that each access point can handle 30 clients at a given time.Configuration Instructions – 1. Click Advanced, Wireless Settings.2. Specify the client limit settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®69Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.2 - Wireless MAC Filter SettingsThe Wireless MAC Filter determines if wireless clients (computers, tablets, smartphones) can access the wireless network as defined by client MAC address. Authorized clients can be configured and viewed in the MAC Filter List.Figure 64. Wireless MAC Filter SettingsPath – Advanced, MAC Filter14.2.1 - MAC Filter SettingsThe MAC Filter Settings screen enables/disables Wireless MAC Filtering.Figure 65. MAC Filter SettingsPath – Advanced, MAC Filter, MAC Filter SettingsParameters – • Enable MAC Filter – Select Yes to enable MAC Filtering. Default: Not Selected.• Filter Mode – Select Allow to permit wireless clients access to the wireless network as defined by wireless client MAC address. Select Deny to prevent wireless clients from accessing the wireless network as defined by wireless client MAC address. OPTIONS: Allow, Deny. Default: Allow.Configuration Instructions – 1. Click Advanced, MAC Filter.2. Specify the wireless MAC filter settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®70Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.2.2 - MAC Filter ListThe Wireless MAC Filter List screen can be used to add/delete wireless clients to be filtered by MAC address.Figure 66. MAC Filter ListPath – Advanced, MAC Filter, MAC Filter ListParameters – • No. – The client number for a device being filtered by MAC address. Default: Not available if MAC Filtering is disabled; client number is in the list if MAC Filtering is enabled.• MAC address – The MAC address of a client being filtered by MAC address, if MAC address filtering is enabled. Default: Blank.• Add – Click to add a new client to be filtered by MAC address.• Delete – Click to delete an existing client.Configuration Instructions – 1. Click Advanced, MAC Filter.2. Specify the MAC filter settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®71Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.3 - WPS SettingsWPS (Wi-Fi Protected Setup) allows setup of WPS-equipped Wi-Fi devices...Figure 67. WPS Settings MenuPath – Advanced, WPSParameters – • Status – Enable or disable WPS.Default: Disabled• Current Configuration – Lists whether the WPS feature is configured or unconfigured.• Release Configuration – Press to release the current configuration settings. All devices connected using the configuration will lose Wi-Fi access.• Self-PIN Code– The Default: Blank.• SSID – The Default: Blank.• Authentication Mode – The Default: Blank.• Encryption Key – The Default: Blank.• WPS via Push Button – The Default: Blank.• WPS via PIN – The Default: Blank.14.3.1 - Configuring WPS Connections...
© 2016 Araknis Networks®72Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.4 - Site SurveyThe access point provides a convenient on-board Wi-Fi detection tool commonly known as a Wi-Fi snier that can be used to detect the presence of other 2.4GHz and 5GHz wireless networks. Parameters such as their modes, channels, security settings, signal strengths, encryptions, and types can be identified. Having this information can be useful during setup to avoid conflicts with other networks in the wireless neighborhood.Figure 68. Site Survey SettingsPath – Advanced, Site Survey14.4.1 - Select InterfaceThe Site Survey Select Interface screen can be used to select the frequency (2.4GHz/5GHz) to be scanned.Figure 69. Site Survey Settings - Select InterfacePath – Advanced, Site Survey, Select InterfaceParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• Select Interface – Select whether to scan for 2.4GHz or 5GHz networks.• Scan Nearby Networks – Click the Scan button to begin a scan.Configuration Instructions – 1. Click Advanced, Site Survey.2. Specify the site survey settings.3. Click Scan.
© 2016 Araknis Networks®73Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.4.2 - ResultThe Site Survey Result shows detected 2.4GHz/5GHz wireless networks, their modes, channels, security settings, signal strengths, encryptions, and type based upon the frequency selected for scanning.Figure 70. Site Survey Settings - shown with scan resultsPath – Advanced, Site Survey, ResultParameters – • BSSID – Basic Service Set Identification. Indicates the MAC address of a detected 2.4GHz or 5GHz neighboring access point.• SSID – Service Set Identifier. Indicates the network name of a wireless network that a specific device is connected to.• Mode – Indicates how a device is being used i.e. AP, bridge, etc.• Channel – Indicates the channel a specific device is transmitting on.• Signal – RSSI or Received Signal Strength Indicator. Indicates the signal strength of a detected network as received by the AN-100/300.• Encryption – Indicates the security mode encryption of a detected device.• Type – Indicates the wireless mode of the detected device.
© 2016 Araknis Networks®74Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.5 - Spectrum Analyzer...Figure 71. Spectrum Analyzer MenuPath – Advanced, Site Survey, ResultParameters – • Select Interface – 2.4 or 5 Ghz antenna.• Scan Bandwidth –• Scan Channel –• RSSI Filter –• Scan Action –
© 2016 Araknis Networks®75Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.6 - Wireless Trac Shaping SettingsTrac shaping is used to regulate packet flow to control wireless network saturation and improve (reduce) latency.Figure 72. Wireless Trac Shaping SettingsPath – Advanced, Trac ShapingParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• Enable – Select to enable Trac Shaping on the 2.4GHz and/or 5GHz band.• SSID – Indicates the network to which Trac Shaping will be applied.• Interface – Indicates 2.4GHz or 5GHz band.• Download Limit – Enter a value to regulate download speed. RANGE: 1-999Mbps. Default: 100Mbps.• Upload Limit – Enter a value to regulate upload speed. RANGE: 1-999Mbps. Default: 100Mbps.Configuration Instructions – 1. Click Advanced, Trac Shaping.2. Specify the wireless trac shaping settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®76Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.7 - SNMP SettingsSimple Network Management Protocol (SNMP) is an IP network protocol that can be used to monitor network devices, audit network usage, detect network faults or inappropriate access, and, in some cases, configure remote devices.Figure 73. SNMP SettingsPath – Advanced, SNMP
© 2016 Araknis Networks®77Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.7.1 - SNMPv2 SettingsThis screen allows configuration of SNMPv2 Settings.Figure 74. SNMP SettingsPath – Advanced, SNMP, SNMPv2Parameters – • Status – Select Enable to enable SNMPv2. Select Disable to disable SNMPv2. Default: Enable• Contact – Enter the name of the person managing the SNMPv2 server. Default: Blank• Location – Enter the physical location of the SNMPv2 server. Default: Blank• Port – Indicates the port number for SNMPv2 ‘listening’.Default: 161 (This is a dedicated TCP/UDP port and typically should not be changed.)• Community Name (Read Only) – Indicates the password for SNMPv2 read only access. Default: Public. ‘Public’ is a typical default of SNMP v2 devices for Read Only.• Community Name (Read Write) – Indicates the password for SNMPv2 read/write access. Default: Private.• Trap Destination – An SNMPv2 Trap is a notification of a network event such as a fault or security event. The Trap Destination is typically the IP address of the SNMP server where trap messages will be sent.• Port – Indicates the SNMPv2 port number for ‘receiving traps’.Default: 162 (This is a dedicated TCP/UDP port and typically should not be changed.)• IP Address – IP address of the SNMPv2 server that will receive SNMP traps.• Community Name – Indicates the password for the SNMPv2 trap community.Configuration Instructions – 1. Click Advanced, SNMP.2. Specify the SNMPv2 settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®78Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.7.2 - SNMPv3 SettingsThis screen allows configuration of SNMPv3 Settings.Figure 75. SNMP SettingsPath – Advanced, SNMP, SNMPv3Parameters – • Status – Select Enable to enable SNMPv3. Select Disable to disable SNMPv3. Default: Enable• Username – Enter a username for SNMPv3 implementation. RANGE: 1-31 Characters. Default: admin.• Authorized Protocol – Select the desired protocol from the drop-down. OPTIONS: MD5, SHA, None. Default: MD5• Authorized Key – Enter an authentication key. This key acts as an electronic signature to authenticate an SNMPv3 message. RANGE: 8-32 Characters. Default: 12345678• Privacy Protocol – Select the desired protocol from the drop-down. OPTIONS: DES, None. Default: DES• Privacy Key – Enter a Privacy Key. This acts as an encryption for the data within a SNMPv3 message. RANGE: 1-8 Characters. Default: 12345678• Engine ID – Enter an Engine ID. The Engine ID identifies where a SNMPv3 message is coming from. Default: BlankConfiguration Instructions – 1. Click Advanced, SNMP.2. Specify the SNMPv3 settings.3. Click Save, then click Apply Changes to enable the new settings.
© 2016 Araknis Networks®79Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.8 - Spanning Tree SettingsSpanning Tree Protocol (STP) is an IP network protocol that prevents undesirable loops caused by multiple active paths between network devices when multiple switches or bridges are used on a network.Figure 76. Spanning Tree SettingsPath – Advanced, SNMP, Spanning TreeParameters – • Status – Enable or Disable STP.Default: Disable• Hello Time – Enter a value for Hello Time. This setting will determine how often in seconds the access point will send the Hello Message to network switches and bridges to assess network topology. RANGE: 1-10 seconds. Default: 2 seconds• Max Age – Enter a duration for Max Age. This setting will determine how long the access point will wait for a Hello Message from another switch or bridge. If no message is received within the set duration, the device will be considered o-line and a new STP route will be configured. RANGE: 6-40 seconds. Default: 20 seconds.• Forward Delay – Enter a value for Forward Delay. This setting will determine the length of time the access point will take to ‘listen’ to the network and either retain current topology or generate a new topology based upon network switch and bridge status. RANGE: 4-30 seconds. Default: 4 seconds.• Priority – Enter a value for Priority from 0-65535. This setting will help determine which bridge is the root bridge, or essentially, the switch that controls the main road that network trac is going to be routed around to avoid loops. In this game, the lowest score wins. The score is a total of MAC address, the Priority number and a bunch of tie-breaker values that determine the root bridge. Setting a lower Priority will help generate a lower score for a given switch.Default: 32768.Configuration Instructions – 1. Click Advanced, Spanning Tree.2. Specify the spanning tree settings.3. Click Save.
© 2016 Araknis Networks®80Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.9 - VLAN SettingsA Virtual Local Area Network (VLAN) is a group of IP Network devices whose IP addresses have been set to run on a particular IP Network. These devices will typically only ‘see’ the other devices on their network and most likely the Internet. A VLAN ID or ‘tag’ can be assigned to data packets that pass through the access point to maintain the integrity of the VLAN by identifying which data belongs to which VLAN.Figure 77. VLAN SettingsPath – Advanced, VLANSParameters – Note – The AN-100 will indicate settings and information for the 2.4GHz channel. The AN-300 will indicate settings and information for the 2.4GHz and 5GHz channels.• VLAN Isolation – Select Yes to assign a VLAN ID. Default: Not selected.• SSID – Indicates the network name of the VLAN being tagged. Any Wireless VLANs that need to be tagged should be added in the Wireless Settings page under Wireless Networks. If a Wireless VLAN does not appear in the VLAN Settings List, check the Wireless Settings page under Wireless Networks to see if it is enabled. If it is not, Enable, Save, then Apply.• Interface – Indicates the 2.4GHz or 5GHz Interface for a given network.• VLAN ID – Enter a value for the VLAN ID. RANGE: 1-4094. Default: BlankConfiguration Instructions – 1. Click Advanced, VLANS.2. Specify the vlan settings.3. Click Save.
© 2016 Araknis Networks®81Araknis Networks Wireless Access PointProduct Manual Advanced Menu-Return to Table of Contents-14.10 - Rogue AP DetectionFigure 78. VLAN SettingsPath – Advanced, VLANSParameters – • Select Interface – .• Detect Rogue AP –• Detect – • Configure Trust AP List – • Trust APs –
© 2016 Araknis Networks®82Araknis Networks Wireless Access PointProduct Manual Troubleshooting-Return to Table of Contents-15 - Troubleshooting15.1 - Hardware Reset ProcedureIf restoring factory defaults does not restore proper functionality to the AN-100/300, a hardware reset may be performed to reload the original base configuration file (saved in the access point’s memory).Figure 79. Reset ButtonReset ButtonConfiguration Instructions – 1. Using a paper clip or other small, blunt tool press the reset button located on the top of the access point for 30 seconds. 2. After two to four minutes, the WAP will reboot. Restart the setup process or upload a previously saved configuration
© 2016 Araknis Networks®83Araknis Networks Wireless Access PointProduct Manual Software Defaults-Return to Table of Contents-16 - Software Defaults16.1 - Basic MenusItem Sub-Item Content AN-100 Default AN-300 Default CommentSYSTEM System Information System Name an100 an300Operation Mode Access PointAdmin Username araknis araknisSystem LED ON ON ON/OFFManagement VLAN Untagged UntaggedWi-Fi Scheduler Status Disable DisableTime Zone Time Zone UTC-05:00 Eastern TimeUTC-05:00 Eastern TimeLAN IP Settings DHCP Enable EnableInterface Settings Speed Auto AutoDuplex AutoWIRELESS Radio Settings Enable Interface Yes YesWireless Mode 802.11 B/G/N 802.11 B/G/N 2.4GHz802.11 A/N 5.0GHzOperating Channel Auto AutoChannel Bandwidth 20 MHz 20 MHz40 MHz 40 MHzExtension Channel Upper Channel (Upper Channel/N/A)Wireless Networks Enable Yes YesName (SSID) araknis_initial araknis_initialInterface 2.4GHz BothSecurity Mode Open OpenYesBroadcast SSID Yes YesChannel Isolation Disable DisableGuest Network Enable Disable YesSECURITY User AccountsUsername araknis araknisPrivilege Level admin adminAccess Control HTTP Port 80 80Web Access Enable EnableTelnet Enable EnableSSH Disable DisableEmail Alert Status Disable DisableDevice Discovery Bonjour Disable DisableUPnP Disable Disable
© 2016 Araknis Networks®84Araknis Networks Wireless Access PointProduct Manual Software Defaults-Return to Table of Contents-16.2 - Advanced MenusItem Sub-Item Content AN-100 Default AN-300 Default CommentWIRELESS SETTINGS Radio Settings Transmit Power Unit dBm dBm dBm/mWData Rate Auto AutoTransmit Power Full 100% Full 100%-29dBmRTS/CTS Threshold (Range:1-2346) 2346 2346Client Limit Enable No NoMax Client No. 127 127MAC FILTER MAC Filter Settings Enable MAC Filter No NoTRAFFIC SHAPINGWireless Trac Shaping Enable Disable DisableSNMP SNMPv2 Settings Status Enable EnablePort 161 161Community Name (Read Only) public publicCommunity Name (Read Write) private privatePort 162 162 Trap DestinationIP Address Trap DestinationCommunity Name public public Trap DestinationSNMPv3 Settings Status Enable EnableUsername admin admin (1-31 Characters)Authorized Protocol MD5 MD5Authorized Key 12345678 12345678Privacy Protocol DES DESPrivacy Key 12345678 12345678Engine IDSPANNING TREESpanning Tree Protocol (STP) Status Disable DisableHello Time 2 2 seconds (1-10)Max Age 20 20 seconds (6-40)Forward Delay 4 4 seconds (4-30)Priority 32768 32768 (0-65535)VLANS VLAN Settings VLAN Isolation No No
© 2016 Araknis Networks®85Araknis Networks Wireless Access PointProduct Manual Table of Figures-Return to Table of Contents-Figure 1. Package Contents 6Figure 2. Residential Access Point Location 8Figure 3. Small Commercial Access Point Location 8Figure 4. EIA/TIA 568B Termination Pattern 9Figure 5. Network Wiring Diagram 10Figure 6. Junction Box Mounting 11Figure 7. Drywall Mounting 12Figure 8. Ceiling Tile Mounting 12Figure 9. Status LED Location 13Figure 10. Default SSID 15Figure 11. EZ Setup Login Screen 15Figure 12. System Name Access 16Figure 13. Fing IP Scanner Example 17Figure 14. Web Interface Layout 21Figure 15. Applying Changes 22Figure 16. System Status Screen 23Figure 17. System Information Table 24Figure 18. Wireless Information 25Figure 19. LAN Information 26Figure 20. System Log 27Figure 21. Wireless Interface Status 28Figure 22. Radio Status 29Figure 23. Utilization of SSID Status 30Figure 24. Wireless Network Status 30Figure 25. Connected Client Status 31Figure 26. System Settings 32Figure 27. System Information 33Figure 28. Date and Time Settings 34Figure 29. Time Zone 35Figure 30. LAN Settings 36Figure 31. IP Settings 37Figure 32. Interface Settings 38Figure 33. Wireless Settings (AN-300-AP-I-N interface shown) 39Figure 34. Radio Settings 40Figure 35. Utilization of SSID Status 41Figure 36. Wireless Networks 42Figure 37. Wireless Security – WPA-PSK and WPA2-PSK Modes 43Figure 38. Wireless Security – WPA-PSK and WPA2-PSK Modes 44Figure 39. Guest Network 4517 - Table of Figures
© 2016 Araknis Networks®86Araknis Networks Wireless Access PointProduct Manual Table of Figures-Return to Table of Contents-Figure 40. Security Settings 47Figure 41. User Accounts 48Figure 42. Access Control 49Figure 43. Email Alert Setup Example 50Figure 44. Common Email Client Ports 51Figure 45. Device Discovery 52Figure 46. Schedule Settings Menu 53Figure 47. Auto Reboot Settings 54Figure 48. Auto Reboot Settings 55Figure 49. Wi-Fi Scheduler 56Figure 50. Wi-Fi Scheduler Menu 57Figure 51. Wi-Fi Scheduler Setup Complete 57Figure 52. Ping Test 58Figure 53. Traceroute Test 59Figure 54. File Management 60Figure 55. Configuration File 61Figure 56. Uploading a New Configuration File 61Figure 57. Restore Factory Defaults 62Figure 58. Firmware 63Figure 59. Restart 64Figure 60. Logout Alert 65Figure 61. Advanced Wireless Settings 66Figure 62. Radio Settings 67Figure 63. Client Limit Settings 68Figure 64. Wireless MAC Filter Settings 69Figure 65. MAC Filter Settings 69Figure 66. MAC Filter List 70Figure 67. WPS Settings Menu 71Figure 68. Site Survey Settings 72Figure 69. Site Survey Settings - Select Interface 72Figure 70. Site Survey Settings - shown with scan results 73Figure 71. Spectrum Analyzer Menu 74Figure 72. Wireless Trac Shaping Settings 75Figure 73. SNMP Settings 76Figure 74. SNMP Settings 77Figure 75. SNMP Settings 78Figure 76. Spanning Tree Settings 79Figure 77. VLAN Settings 80Figure 78. VLAN Settings 81Figure 79. Reset Button 82
© 2016 Araknis Networks®87Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-18 - Specifications100/300 SeriesDescription AN-100-AP-I-N AN-300-AP-I-NInterfacesRJ45 10/100/1000Base-T 1PoE 802.3at/af compliant YesWireless Interface 802.11 b/g/n 802.11 a/b/g/nEmbedded Antennas YesPerformanceAntenna Type Omni-directionalTransmit Power See MCS tableReceiver Sensitivity See MCS table802.11n 2x2:2 MIMOPHY Data Rate Up to 300 Mbps Up to 300 Mbps in both frequency bandsOperating Frequencies 2.4GHz 2.4GHz & 5GHzChannel Bonding Yes (20MHz and 40MHz)Memory 64MB 128MBFlash Memory 16MB 16MBWireless FeaturesAuto Channel Selection YesOperation Modes Access PointMultiple SSIDs Yes -up to 8Wireless Security WPA2-PSK (AES + TKIP), WPA-EnterpriseMAC Address Filtering YesHide SSID YesGuest Network YesL2 featuresVLANs Yes - 802.1Q QoS Yes - WME 802.11eRJ45 Auto-sensing YesRJ45 Auto-negotiation YesSpanning Tree Protocol Yes, 802.1d
© 2016 Araknis Networks®88Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-Description AN-100-AP-I-N AN-300-AP-I-NManagementWeb Management YesTelnet YesSNMP v1, v2c, v3 YesDHCP client YesSystem Log YesBonjour YesAraknis EZ Access YesUPnP YesRemote Config File Download/Upload YesOvrC Cloud Services YesWi-Fi Scheduler YesSite Survey YesLED Control YesAuto Reboot YesEnvironmental & PhysicalDimensions (W-H-D) 6.9 x 6.9 x 1.3External Power Supply 12V 1A DC 12V 2A DCTemperature Range Operating: 32º to 122ºF( 0 to 50ºC) Storage: -4Fº to 140ºF(-20ºC to 60ºC)Humidity Operating: 90% or less Storage: 90% or lessCertifications CE, FCC, IC, Wi-Fi®
© 2016 Araknis Networks®89Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-MCS Table (RF Performance)Channel Bonding Data RangeTransmit Power (combined, dBm)Receive Sensitivity (combined, dBm)AN-100-AP-I-N802.11b @ 2.4 GHz 1 Mbps 29 < -9311 Mbps 29 < -90802.11g @ 2.4 GHz 6 Mbps 28 < -8954 Mbps 25 < -71802.11n HT20 @ 2.4 GHz MCS 0/8 27 < -87MCS 7/15 24 < -69802.11n HT40 @ 2.4GHz MCS 0/8 27 < -87MCS 7/15 24 < -69AN-300-AP-I-N802.11a @ 5GHz 6 Mbps 26 < 9054 Mbps 23 < -72802.11b @ 2.4 GHz 1 Mbps 29 < -9911 Mbps 29 < -93802.11g @ 2.4 GHz 6 Mbps 29 < -9654 Mbps 23 < -82802.11n HT20 @ 2.4 GHz MCS 0/8 29 < -97MCS 7/15 23 < -78802.11n HT40 @ 2.4GHz MCS 0/8 29 < -86MCS 7/15 23 < -69802.11n HT20 @ 5GHz MCS 0/8 26 < -89MCS 7/15 23 < -70802.11n HT40 @ 5GHz MCS 0/8 26 < -87MCS 7/15 23 < -68
© 2016 Araknis Networks®90Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-500/700 SeriesDescription AN-500-AP-I-AC AN-700-AP-I-ACInterfacesRJ45 10/100/1000Base-T 1PoE 802.3at/af compliant YesWireless Interface 802.11 a/b/g/n/ac 802.11 a/b/g/n/acEmbedded Antennas YesPerformanceAntenna Type Omni-directionalTransmit Power See MCS tableReceiver Sensitivity See MCS table802.11n 2x2:2 MIMO 3x3:3 MIMOPHY Data Rate Up to 300Mbps @ 2.4GHzUp to 867Mbps @ 5GHzUp to 450Mbps @ 2.4GHzUp to 1300Mbps @ 5GHzOperating Frequencies 2.4GHz & 5GHzChannel Bonding Yes (20MHz, 40MHz, and 80MHz)Max TX Power 28dBm @ 2.4GHz26dBm @ 5GHzMemory 64MB 128MBFlash Memory 16MB 16MBWireless FeaturesAuto Channel Selection YesOperation Modes Access Point, RepeaterMultiple SSIDs Yes -up to 8 per radioWireless Security WPA2-PSK (AES + TKIP), WPA-EnterpriseMAC Address Filtering YesHide SSID YesGuest Network YesL2 featuresVLANs Yes - 802.1Q QoS Yes - WME 802.11eRJ45 Auto-sensing YesRJ45 Auto-negotiation YesSpanning Tree Protocol Yes, 802.1d
© 2016 Araknis Networks®91Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-Description AN-500-AP-I-AC AN-700-AP-I-ACManagementWeb Management YesTelnet YesSNMP v1, v2c, v3 YesDHCP client YesSystem Log YesBonjour YesAraknis EZ Access YesUPnP YesRemote Config File Download/Upload YesOvrC Cloud Services YesWi-Fi Scheduler YesSite Survey YesLED Control YesAuto Reboot YesEnvironmental & PhysicalDimensions (W-H-D) 6.9" x 6.9" x 1.3" 6.9" x 6.9" x 1.6"External Power Supply 12V 2A DCTemperature Range Operating: 32º to 122ºF( 0 to 50ºC) Storage: -4Fº to 140ºF(-20ºC to 60ºC)Humidity Operating: 90% or less Storage: 90% or lessCertifications CE, FCC, IC, Wi-Fi®
© 2016 Araknis Networks®92Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-MCS Table (RF Performance)Channel Bonding Data RangeTransmit Power (combined, dBm)Receive Sensitivity (combined, dBm)AN-500-AP-I-AC802.11b @ 2.4 GHz 1 Mbps 29 < -9311 Mbps 29 < -90802.11g @ 2.4 GHz 6 Mbps 28 < -8954 Mbps 25 < -71802.11n HT20 @ 2.4 GHz MCS 0/8 27 < -87MCS 7/15 24 < -69802.11n HT40 @ 2.4GHz MCS 0/8 27 < -87MCS 7/15 24 < -69AN-700-AP-I-AC802.11a @ 5GHz 6 Mbps 26 < 9054 Mbps 23 < -72802.11b @ 2.4 GHz 1 Mbps 29 < -9911 Mbps 29 < -93802.11g @ 2.4 GHz 6 Mbps 29 < -9654 Mbps 23 < -82802.11n HT20 @ 2.4 GHz MCS 0/8 29 < -97MCS 7/15 23 < -78802.11n HT40 @ 2.4GHz MCS 0/8 29 < -86MCS 7/15 23 < -69802.11n HT20 @ 5GHz MCS 0/8 26 < -89MCS 7/15 23 < -70802.11n HT40 @ 5GHz MCS 0/8 26 < -87MCS 7/15 23 < -68^^TBD^^
© 2016 Araknis Networks®93Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-CE WarningThis is a product with CE certification. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.AN-100-AP-I-N FCC StatementFederal Communication Commission Interference StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.Industry Canada statement:This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
© 2016 Araknis Networks®94Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-Déclaration d’exposition aux radiations:Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.Europe – EU Declaration of ConformityThis device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:• EN60950-1Safety of Information Technology Equipment• EN50385Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz)• EN 300 328Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive• EN 301 489-1Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements• EN 301 489-17Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment 0560Česky [Czech] Araknis Networks tímto prohlašuje, že tento wireless access point je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.Dansk [Danish]Undertegnede Araknis Networks erklærer herved, at følgende udstyr wireless access point overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.Deutsch [German]Hiermit erklärt Araknis Networks, dass sich das Gerät wireless access point in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.Eesti [Estonian]Käesolevaga kinnitab Araknis Networks seadme wireless access point vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.English Hereby, Araknis Networks , declares that this wireless access point is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
© 2016 Araknis Networks®95Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-Español [Spanish]Por medio de la presente Araknis Networks declara que el wireless access point cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.Ελληνική [Greek]ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Araknis Networks ΔΗΛΩΝΕΙ ΟΤΙ wireless access point ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.Français [French]Par la présente Araknis Networks déclare que l›appareil wireless access point est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.Italiano [Italian]Con la presente Araknis Networks dichiara che questo wireless access point è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Latviski [Latvian]Ar šo Araknis Networks deklarē, ka wireless access point atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.Lietuvių [Lithuanian] Šiuo Araknis Networks deklaruoja, kad šis wireless access point atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.Nederlands [Dutch]Hierbij verklaart Araknis Networks dat het toestel wireless access point in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.Malti [Maltese] Hawnhekk, Araknis Networks, jiddikjara li dan wireless access point jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.Magyar [Hungarian]Alulírott, Araknis Networks nyilatkozom, hogy a wireless access point megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.Polski [Polish]Niniejszym Araknis Networks oświadcza, że wireless access point jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.Português [Portuguese]Araknis Networks declara que este wireless access point está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.Slovensko [Slovenian]Araknis Networks izjavlja, da je ta wireless access point v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.Slovensky [Slovak]Araknis Networks týmto vyhlasuje, že wireless access point spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.Suomi [Finnish]Araknis Networks vakuuttaa täten että wireless access point tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Svenska [Swedish]Härmed intygar Araknis Networks att denna wireless access point står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
© 2016 Araknis Networks®96Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-AN-300-AP-I-N FCC StatementFederal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Operations in the 5.15-5.25GHz band are restricted to indoor usage only.IMPORTANT NOTE:FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 21cm between the radiator & your body.Industry Canada Statement:This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Caution:(i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
© 2016 Araknis Networks®97Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-Avertissement:(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;(ii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.FOR MOBILE DEVICE USAGERadiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 21cm between the radiator & your body.Déclaration d’exposition aux radiations:Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 21cm de distance entre la source de rayonnement et votre corps.Europe – EU Declaration of ConformityThis device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:• EN60950-1Safety of Information Technology Equipment• EN50385Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz)• EN 300 328Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive• EN 301 893Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive• EN 301 489-1Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements• EN 301 489-17Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment
© 2016 Araknis Networks®98Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-This device is a 5GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. 0560Česky [Czech] Araknis Networks tímto prohlašuje, že tento wireless access point je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.Dansk [Danish]Undertegnede Araknis Networks erklærer herved, at følgende udstyr wireless access point overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.Deutsch [German]Hiermit erklärt Araknis Networks, dass sich das Gerät wireless access point in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.Eesti [Estonian]Käesolevaga kinnitab Araknis Networks seadme wireless access point vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.English Hereby, Araknis Networks, declares that this wireless access point is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Español [Spanish]Por medio de la presente Araknis Networks declara que el wireless access point cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.Ελληνική [Greek]ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Araknis Networks ΔΗΛΩΝΕΙ ΟΤΙ wireless access point ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.Français [French]Par la présente Araknis Networks déclare que l›appareil wireless access point est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.Italiano [Italian]Con la presente Araknis Networks dichiara che questo wireless access point è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Latviski [Latvian]Ar šo Araknis Networks deklarē, ka wireless access point atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.Lietuvių [Lithuanian] Šiuo Araknis Networks deklaruoja, kad šis wireless access point atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.Nederlands [Dutch]Hierbij verklaart Araknis Networks dat het toestel wireless access point in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
© 2016 Araknis Networks®99Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-Malti [Maltese] Hawnhekk, Araknis Networks, jiddikjara li dan wireless access point jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.Magyar [Hungarian]Alulírott, Araknis Networks nyilatkozom, hogy a wireless access point megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.Polski [Polish]Niniejszym Araknis Networks oświadcza, że wireless access point jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.Português [Portuguese]Araknis Networks declara que este wireless access point está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.Slovensko [Slovenian]Araknis Networks izjavlja, da je ta wireless access point v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.Slovensky [Slovak]Araknis Networks týmto vyhlasuje, že wireless access point spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.Suomi [Finnish]Araknis Networks vakuuttaa täten että wireless access point tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Svenska [Swedish]Härmed intygar Araknis Networks att denna wireless access point står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
© 2016 Araknis Networks®100Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-AN-500/700-AP-I-AC FCC StatementFederal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Operations in the 5.15-5.25GHz band are restricted to indoor usage only.IMPORTANT NOTE:FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 21cm between the radiator & your body.Industry Canada statement:This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
© 2016 Araknis Networks®101Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-Caution:(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.Avertissement:(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;(ii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.FOR MOBILE DEVICE USAGERadiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 22cm between the radiator & your body.Déclaration d’exposition aux radiations:Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 22cm de distance entre la source de rayonnement et votre corps.Europe – EU Declaration of ConformityThis device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:EN60950-1Safety of Information Technology EquipmentEN50385Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz)EN 300 328Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive
© 2016 Araknis Networks®102Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-EN 301 893Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering essential requirements of article 3.2 of the R&TTE DirectiveEN 301 489-1 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirementsEN 301 489-17Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment Česky [Czech] Araknis Networks tímto prohlašuje, že tento wireless access point je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.Dansk [Danish]Undertegnede Araknis Networks erklærer herved, at følgende udstyr wireless access point overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.Deutsch [German]Hiermit erklärt Araknis Networks, dass sich das Gerät wireless access point in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.Eesti [Estonian]Käesolevaga kinnitab Araknis Networks seadme wireless access point vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.English Hereby, Araknis Networks, declares that this wireless access point is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Español [Spanish]Por medio de la presente Araknis Networks declara que el wireless access point cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.Ελληνική [Greek]ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Araknis Networks ΔΗΛΩΝΕΙ ΟΤΙ wireless access point ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.Français [French]Par la présente Araknis Networks déclare que l›appareil wireless access point est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.Italiano [Italian]Con la presente Araknis Networks dichiara che questo wireless access point è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Latviski [Latvian]Ar šo Araknis Networks deklarē, ka wireless access point atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.Lietuvių [Lithuanian] Šiuo Araknis Networks deklaruoja, kad šis wireless access point atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
© 2016 Araknis Networks®103Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-Nederlands [Dutch]Hierbij verklaart Araknis Networks dat het toestel wireless access point in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.Malti [Maltese] Hawnhekk, Araknis Networks, jiddikjara li dan wireless access point jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.Magyar [Hungarian]Alulírott, Araknis Networks nyilatkozom, hogy a wireless access point megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.Polski [Polish]Niniejszym Araknis Networks oświadcza, że wireless access point jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.Português [Portuguese]Araknis Networks declara que este wireless access point está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.Slovensko [Slovenian]Araknis Networks izjavlja, da je ta wireless access point v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.Slovensky [Slovak]Araknis Networks týmto vyhlasuje, že wireless access point spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.Suomi [Finnish]Araknis Networks vakuuttaa täten että wireless access point tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Svenska [Swedish]Härmed intygar Araknis Networks att denna wireless access point står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
© 2016 Araknis Networks®104Araknis Networks Wireless Access PointProduct Manual Specifications-Return to Table of Contents-2-Year Limited WarrantyAraknis Networks® products have a 2-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products that have been abused, modified, or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization number (RA).Contacting Technical SupportP: (866) 838-5052E: Techsupport@araknisnetworks.com
© 2016 Araknis Networks®160225-1513

Navigation menu