Arada Systems MAXR3210 WIRELESS ACCESS POINT User Manual FullManual22dec09

Arada Systems, Inc WIRELESS ACCESS POINT FullManual22dec09

UserManual.wiki >

Arada Systems >

MAXR3210 User Manual

Users Manual

ARADA, Inc.1024 Morse Avenue,Sunnyvale,CA 94089Arada Systems Inc.,1024 Morse Avenue,Sunnyvale, CA - 94089.Tel: +1 (408) 773 9298www.aradasystems.comArada Systems, Inc.MaxR-3210 Single Band Wireless-N Access Point User Manual This document helps you to configure and use the MaxR-3210 Single Band Wireless-N Access PointDec 2009Book Version: 1.1

iiFederal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.• Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modifications not expressly approved by the party responsible forcompliance could void the user's authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired operation.This device and its antenna(s) must not be co-located or operating in conjunction with any otherantenna or transmitter.FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolledenvironment. This equipment should be installed and operated with minimum distance 20cmbetween the radiator & your body.

ContentsAbout This ManualConventions, Formats, and Scope ..................................................................................... iChapter 1 IntroductionAbout the MaxR-3210 Single Band Wireless-N Access Point ........................................1-1Key Features and Standards ..........................................................................................1-1Supported Standards and Conventions ...................................................................1-2Key Features ............................................................................................................1-2802.11b/g/n Standards-based Wireless Networking ................................................1-4Autosensing Ethernet Connections with Auto Uplink ...............................................1-4System Requirements ....................................................................................................1-4What’s In the Box? .........................................................................................................1-5Hardware Description .....................................................................................................1-5Rear Panel ...............................................................................................................1-5Chapter 2 Basic Installation and ConfigurationWireless Equipment Placement and Range Guidelines .................................................2-2Understanding MaxR-3210 Wireless Security Options ..................................................2-3Installing the MaxR-3210 Wireless Access Point ...........................................................2-4Setting up the MaxR-3210 Wireless Access Point ...................................................2-4Configuring LAN and Wireless Access ....................................................................2-4Configuring Time Settings .................................................................................2-7Configuring Wireless Access .............................................................................2-9Deploying the MaxR-3210 Wireless Access Point ...................................................2-9Verifying Wireless Connectivity ..............................................................................2-10Logging In Using the Default IP Address ......................................................................2-10Setting Basic IP Options ............................................................................................... 2-11Wireless Settings ..........................................................................................................2-13Configuring 802.11b/bg/ng Wireless Settings ........................................................2-13

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential vv1.1, Dec 2009Packet Capture .............................................................................................................3-21Chapter 4 Advanced ConfigurationIP Settings for Wireless Clients ......................................................................................4-1Hotspot Settings .............................................................................................................4-3Configuring Advanced Wireless Settings .......................................................................4-4Configuring 802.11b/bg/ng Advanced Wireless Settings .........................................4-4Configuring Advanced QoS Settings ..............................................................................4-6Enabling Wireless Bridging .............................................................................................4-8Configuring an MaxR-3210 as a Point-to-Point Bridge ..........................................4-12Configuring an MaxR-3210 as a Point-to-Multi-Point Wireless Bridge ...................4-13Chapter 5 Troubleshooting and DebuggingNo lights are lit on the Access Point. ..............................................................................5-1The Wireless LAN activity light does not light up. ...........................................................5-1The LAN light is not lit. ....................................................................................................5-2I cannot access the Internet or the LAN with a wireless capable computer. .................5-2I cannot connect to the MaxR-3210 to configure it. ........................................................5-3When I enter a URL or IP address I get a timeout error. ................................................5-3Using the Reset Button to Restore Factory Default Settings ..........................................5-4Appendix A Default Settings and Technical SpecificationsFactory Default Settings ................................................................................................ A-1Technical Specifications ................................................................................................. A-3Appendix B Command Line ReferenceCommand Sets .............................................................................................................. B-1Index

MaxR-3210 Wireless-N Access Point User Manualvi Arada Systems Confidentialv1.1, Dec 2009

Arada Systems Confidential iv1.1, Dec 2009About This ManualThe MaxR-3210 Single Band Wireless-N Access Point User Manual describes how to install, configure and troubleshoot the MaxR-3210 Wireless Access Point. The information in this manual is intended for readers with intermediate computer and Internet skills.Conventions, Formats, and ScopeThe conventions, formats, and scope of this manual are described in the following paragraphs:•Typographical Conventions. This manual uses the following typographical conventions:•Formats. This manual uses the following formats to highlight special messages:Italic Emphasis, books, CDs, file and server names, extensionsBold User input, IP addresses, GUI screen textFixed Command prompt, CLI text, code italic URL linksNote: This format is used to highlight information of importance or special interest.Tip: This format is used to highlight a procedure that will save time or resources.Warning: Ignoring this type of note may result in a malfunction or damage to the equipment.

MaxR-3210 Wireless-N Access Point User Manualii Arada Systems Confidentialv1.1, Dec 2009Danger: This is a safety warning. Failure to take heed of this notice may result in personal injury or death.

Arada Systems Confidential 1v1.1, Dec 2009Chapter 1IntroductionThis chapter describes some of the key features of the MaxR-3210 Single Band Wireless-N Access Point. It also includes the minimum prerequisites for installation (“System Requirements” on page 1-4.), package contents (“What’s In the Box?” on page 1-5) and a description of the front and back panels of the MaxR-3210 (“Hardware Description” on page 1-5).About the MaxR-3210 Single Band Wireless-N Access PointThe MaxR-3210 Single Band Wireless-N Access Point is the basic building block of a wireless LAN infrastructure. It provides connectivity between Ethernet wired networks and radio-equipped wireless notebook systems, desktop systems, print servers, and other devices.The MaxR-3210 provides wireless connectivity to multiple wireless network devices within a fixed range or area of coverage—interacting with a wireless network interface card (NIC) via an antenna. Typically, an individual in-building access point provides a maximum connectivity area of about a 500 foot radius. Consequently, the MaxR-3210 Single Band Wireless-N Access Point can support a small group of users in a range of several hundred feet. Most access points can handle between 10 to 30 users simultaneously per radio.The MaxR-3210 Single Band Wireless-N Access Point acts as a bridge between the wired LAN and wireless clients. Connecting multiple MaxR-3210 Wireless Access Points via a wired Ethernet backbone can further lengthen the wireless network coverage. As a mobile computing device moves out of the range of one access point, it moves into the range of another. As a result, wireless clients can freely roam from one Access Point to another and still maintain seamless connection to the network.Key Features and StandardsThe MaxR-3210 Wireless Access Point is easy-to-use and provides solid wireless and networking support. It also offers a wide range of security options.

MaxR-3210 Wireless-N Access Point User Manual2 Arada Systems Confidentialv1.1, Dec 2009Supported Standards and ConventionsThe following standards and conventions are supported:•Standards Compliance. The Wireless Access Point complies with the IEEE 802.11b/g/n standards for Wireless LANs.•Full WPA and WPA2 support. WPA and WPA2 enterprise-class strong security with RADIUS and certificate authentication as well as dynamic encryption key generation.WPA-PSK and WPA2-PSK preshared key authentication without the overhead of RADIUS servers but with all of the strong security of WPA.•Multiple BSSIDs. Supports multiple BSSIDs. When a Access Point is connected to a wired network and a set of wireless stations, it is called a Basic Service Set (BSS). The Basic Service Set Identifier (BSSID) is a unique identifier attached to the header of packets sent over a WLAN that differentiates one WLAN from another when a mobile device tries to connect to the network.The multiple BSSID feature allows you to configure up to 8 SSIDs on your MaxR-3210 access point and assign different configuration settings to each SSID. All the configured SSIDs are active and the network devices can connect to the access point by using any of these SSIDs.•DHCP Client Support. DHCP provides a dynamic IP address to PCs and other devices upon request. The MaxR-3210 can act as a client and obtain information from your DHCP server; it can also act as a DHCP server and provide network information for wireless clients.•SNMP Support. Support for Simple Network Management Protocol (SNMP) Management Information Base (MIB) management.• 802.1Q VLAN (Virtual LAN) Support. A network of computers that behave as if they are connected to the same network even though they actually may be physically located on different segments of a LAN. VLANs are configured through software rather than hardware, which makes them extremely flexible. VLANs are very useful for user/host management, bandwidth allocation and resource optimization. Key FeaturesThe MaxR-3210 provides solid functionality, including the following features:•2.4Ghz Band Operating Frequency. The Wireless Access Point operates in the 2.4 GHz frequency band.• Multiple operating modes:– Wireless Access Point. Operates as a standard 802.11b/bg/ng access point.

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 3v1.1, Dec 2009– Point-to-Point Bridge. In this mode, the MaxR-3210 only communicates with another bridge-mode wireless access point (with or without clients). Network authentication should be used to protect this communication. – Point-to-Multi-Point Bridge. Select this only if this MaxR-3210 is the “Master” for a group of bridge-mode wireless access points. The other bridge-mode wireless access points send all traffic to this “Master”, and do not communicate directly with each other. Network Authentication should be used to protect this traffic. • Hotspot Settings. You can allow the first HTTP (TCP, port 80) request, on client association, to be captured and redirected to the URL you specify.•Upgradeable Firmware. Firmware is stored in a flash memory and can be upgraded easily, using only your Web browser, and can be upgraded remotely. In addition to using Web browser to do so, command-line interface and SNMP can also be used.•Rogue AP detection. The Rogue AP detection feature shows a list of unknown APs to the administrator.•Access Control. The Access Control MAC address filtering feature can ensure that only trusted wireless stations can use the MaxR-3210 to gain access to your LAN.•Security Profiles. When using multiple BSSIDs, you can configure unique security settings (encryption, SSID, etc.) for each BSSID.•Hidden Mode. The SSID is not broadcast, assuring only clients configured with the correct SSID can connect.•Secure Telnet Command Line Interface. The secure Telnet command line interface enables direct secure access over the serial port and easy scripting of configuration of multiple MaxR-3210s across an extensive network via the Ethernet interface. An SSH client is required.•Configuration Backup. Configuration settings can be backed up to a file and restored.•Power over Ethernet. Power can be supplied to the MaxR-3210 over the Ethernet port from any 802.3af compliant mid-span or end-span source.•Autosensing Ethernet Connection with Auto Uplink Interface. Connects to 10/100/1000 Mbps IEEE 802.3 Ethernet networks.•LED Indicators. Power/Test, LAN speed, LAN activity, and wireless activity for each radio mode are easily identified.• Wireless Multimedia (WMM) Support. WMM is a subset of the 802.11e standard. WMM allows wireless traffic to have a range of priorities, depending on the kind of data. Time-dependent information, like video or audio, has a higher priority than normal traffic. For WMM to function correctly, Wireless clients must also support WMM.

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 5v1.1, Dec 2009• The Category 5 UTP straight through Ethernet cable with RJ-45 connector included in the package, or one like it• A 100-240 V, 50-60 Hz AC power source• A Web browser for configuration such as Microsoft Internet Explorer 5.0 or above, or Mozilla 3.0 or above• At least one computer with the TCP/IP protocol installed• 802.11b/g/n-compliant devices.What’s In the Box?The product package should contain the following items:• MaxR-3210 Single Band Wireless-N Access Point • Three Reverse SMA 5dbi dual band dipole antennas.• Power adapter and cord (12 V dc, 1.5 A)• Straight through Category 5 Ethernet cable• RJ-45 to DB-9 female connector.•Resource CD which includes this manual.• Support Registration cardContact your reseller or customer support in your area if there are any missing or damaged parts. You can refer to the Support Information Card for the telephone number of customer support in your area. You should keep the Support Information card, along with the original packing materials, and use the packing materials to repack the MaxR-3210 if you need to return it for repair. Hardware DescriptionThis section describes the rear panel hardware functions of the MaxR-3210.Rear PanelThe MaxR-3210 rear panel functions are described below:1. Left, Middle, and Right Detachable AntennaThe MaxR-3210 provides three detachable antennas.

MaxR-3210 Wireless-N Access Point User Manual6 Arada Systems Confidentialv1.1, Dec 20092. Restore to Factory Defaults ButtonThe restore to default button is located next to the RJ-45 console port and restores the MaxR-3210 to the factory default settings.3. Serial Console PortRJ-45 serial console port for serial DTE connections.4. RJ-45 Ethernet PortUse the MaxR-3210 Ethernet RJ-45 port to connect to an Ethernet LAN through a device such as a hub, switch, router, or PoE switch.5. Power SocketThis socket connects to the MaxR-3210 12V 1.5A power adapter.

Arada Systems Confidential 1v1.1, Dec 2009Chapter 2Basic Installation and ConfigurationThis chapter describes how to set up your MaxR-3210 Single Band Wireless-N Access Point for wireless connectivity to your LAN. This basic configuration will enable computers with 802.11b/g/n wireless adapters to do such things as connect to the Internet, or access printers and files on your LAN.This chapter contains the following sections:1. “Wireless Equipment Placement and Range Guidelines2. “Understanding MaxR-3210 Wireless Security Options3. “Installing the MaxR-3210 Wireless Access Point4. “Logging In Using the Default IP Address5. “Setting Basic IP Options6. “Wireless Settings7. “Setting Up and Testing Basic Wireless Connectivity8. “Understanding Security Profiles9. “SSID and WEP/WPA Settings Setup Form10. “Configuring the RADIUS Server Settings11. “Setting up a Security Profile12. “Configuring WEP13. “Configuring WPA with RADIUSNote: Indoors, computers can connect over 802.11b/bg/ng wireless networks at ranges of several hundred feet or more. This distance can allow for others outside your area to access your network. It is important to take appropriate steps to secure your network from unauthorized access. The MaxR-3210 Wireless Access Point provides highly effective security features which are covered in detail in “Understanding Security Profiles” on page 2-18. Deploy the security features appropriate to your needs.

MaxR-3210 Wireless-N Access Point User Manual2 Arada Systems Confidentialv1.1, Dec 200914. “Configuring WPA2 with RADIUS15. “Configuring WPA and WPA2 with RADIUS16. “Configuring WPA-PSK17. “Configuring WPA2-PSK18. “Configuring WPA-PSK and WPA2-PSK19. “Restricting Wireless Access by MAC AddressYou need to prepare these three things before you can establish a connection through your wireless access point:• A location for the MaxR-3210 that conforms to the “Wireless Equipment Placement and Range Guidelines below.• The wireless access point connected to your LAN through a device such as a hub, switch, router, or Cable/DSL gateway. • One or more computers with properly configured 802.11b/g/n wireless adapters.Wireless Equipment Placement and Range GuidelinesThe operating distance or range of your wireless connection can vary significantly based on the physical placement of the Access Point. The latency, data throughput performance, and notebook power consumption of wireless adapters also vary depending on your configuration choices.For best results, place your Access Point:• Near the center of the area in which your PCs will operate.• In an elevated location such as a high shelf where the wirelessly connected PCs have line-of-sight access (even if through walls).• Away from sources of interference, such as PCs, microwaves, and 2.4 GHz cordless phones.• Away from large metal surfaces.Putting the antenna in a vertical position provides best side-to-side coverage. Putting the antenna in a horizontal position provides best up-and-down coverage. Note: Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the MaxR-3210. For complete performance specifications, see Appendix A, “Default Settings and Technical Specifications.”

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 3v1.1, Dec 2009If you are using multiple access points for 11b/bg/ng, it is better if adjacent access points use different radio frequency channels to reduce interference. The recommended Channel spacing between adjacent access points is 5 Channels (for example, use Channels 1 and 6, or 6 and 11).The time it takes to establish a wireless connection can vary depending on both your security settings and placement. Some types of security connections can take slightly longer to establish and can consume more battery power on a notebook computer.Understanding MaxR-3210 Wireless Security OptionsYour wireless data transmissions can be received well beyond your walls by anyone with a compatible adapter. For this reason, use the security features of your wireless equipment. The MaxR-3210 Wireless Access Point provides highly effective security features which are covered in detail in this chapter. Deploy the security features appropriate to your needs.There are several ways you can enhance the security of your wireless network:•Restrict Access Based on MAC address. You can restrict access to only trusted PCs so that unknown PCs cannot wirelessly connect to the MaxR-3210. MAC address filtering adds an obstacle against unwanted access to your network, but the data broadcast over the wireless link is fully exposed. •Turn Off the Broadcast of the Wireless Network Name (SSID). If you disable broadcast of the SSID, only devices that have the correct SSID can connect. This nullifies the wireless network “discovery” feature of some products such as Windows XP, Vista and Unix systems but the data is still fully exposed to a determined snoop using specialized test equipment like wireless sniffers.•Use WEP. Wired Equivalent Privacy (WEP) data encryption provides data security. WEP open authentication and WEP data encryption will block all but the most determined eavesdropper. •Use WPA or WPA-PSK. Wi-Fi Protected Access (WPA) data encryption provides data security. The very strong authentication along with dynamic per frame rekeying of WPA make it virtually impossible to compromise. Because this is a new standard, wireless device driver and software availability may be limited.Note: WEP and TKIP provide only legacy rates of operation. So, AES is the recommended solution to use the 802.11n rates and speed.

MaxR-3210 Wireless-N Access Point User Manual4 Arada Systems Confidentialv1.1, Dec 2009Installing the MaxR-3210 Wireless Access PointBefore installing the MaxR-3210 Single Band Wireless-N Access Point, you should make sure that your Ethernet network is up and working. You will be connecting the access point to the Ethernet network so that computers with 802.11b/g/n wireless adapters will be able to communicate with computers on the Ethernet network. In order for this to work correctly, verify that you have met all of the system requirements, shown on “System Requirements” on page 1-4.Setting up the MaxR-3210 Wireless Access PointTo set up the MaxR-3210 Wireless Access Point:1. Prepare a computer with an Ethernet adapter. If this computer is already part of your network, record its TCP/IP configuration settings. 2. Configure the computer with a static IP address of 192.168.0.210 and 255.255.255.0 for the Subnet Mask.3. Connect an Ethernet cable from the MaxR-3210 to the computer. 4. Turn on your computer, connect the power adapter to the MaxR-3210 and verify the following:• The PWR power light goes on. • The LAN light of the Access Point is lit when connected to a powered on computer.• The WLAN LEDs should be blinking.Configuring LAN and Wireless Access To configure the MaxR-3210 Ethernet port for LAN access: 1. Connect to the MaxR-3210 by opening your browser and entering http://192.168.0.237 in the address field. The MaxR-3210 login screen appears (see Figure 2-1).2. Enter admin for the user name and password for the password, both in lower case letters.Tip: Before mounting the MaxR-3210 in a high location, first set up and test the MaxR-3210 to verify wireless network connectivity.

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 5v1.1, Dec 20093. Click Login. The main menu of the MaxR-3210 displays as shown in Figure 2-2.• When the Access Point is connected to the Internet, under the Support tab, select Documentation to view the documentation for the Access Point.• On the top-right of the screen, select Logout to exit the MaxR-3210 setup screens. (You will automatically be logged out of the Access Point after 5 minutes of no activity.)4. Access Point Name: Enter the access point name of the MaxR-3210.This unique name is the access point NetBIOS name. The default Access Point Name is located on the bottom label of MaxR-3210. The default is aradaxxxxxx, where xxxxxx represents the last 6 digits of the MaxR-3210 MAC address. You may modify the default name with a unique name up to 15 characters long. Figure 2-1 Login screen

MaxR-3210 Wireless-N Access Point User Manual6 Arada Systems Confidentialv1.1, Dec 20095. Select Time from the left panel. The Time screen displays, as shown in Figure 2-2. 6. Enter the Time Settings for your area. See the online help or “Configuring Time Settings” on page 2-7 for more information about how to configure the settings on this screen.Figure 2-2 Timezone and system time related settings

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 7v1.1, Dec 20097. Select IP on the main menu. The IP Settings screen displays, as shown in Figure 2-3. 8. Configure the IP Address settings appropriate for your network. The default values are suitable for most users and situations. (See the online help or “Setting Basic IP Options” on page 2-11 for more information about how to configure the settings on this screen.9. Click Apply.Configuring Time SettingsTo configure your time settings:1. Under the Configuration tab, select System from the main menu, select Basic, and then select Time. The Time screen displays, as shown in Figure 2-4. Figure 2-3 IP Settings

MaxR-3210 Wireless-N Access Point User Manual8 Arada Systems Confidentialv1.1, Dec 20092. Configure the following information:–Time Zone. From the pull-down menu, select the local time zone for your Access Point from a list of all available time zones. The default is USA-Pacific.–NTP Client. Enable NTP Client to synchronize the time of the access point with an NTP Server. The Default is Enabled.–Use Custom NTP Server. Check the option if you have a custom NTP server. The default is Disabled.–Hostname / IP Address. Enter the host name or the IP address of the custom NTP server.3. Click Apply.Figure 2-4 Timezone and system time related settingsNote: You must have an Internet connection to get the current time.

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 9v1.1, Dec 2009Configuring Wireless AccessTo configure your wireless settings for 11b/bg/ng:1. From the main menu under Configuration, select Wireless. The Wireless Settings screen displays, as shown in Figure 2-5. 2. Enter the wireless settings for your area. See the online help or “Wireless Settings” on page 2-13.3. Click Apply to save your settings.When you have completed the setup steps, you can deploy the MaxR-3210 in your network. If needed, you can now reconfigure the computer you used in step 1 (from the Static IP) back to its original TCP/IP settings.Deploying the MaxR-3210 Wireless Access PointTo deploy the MaxR-3210 Wireless Access Point:1. Disconnect the MaxR-3210 and position it where it will be deployed. The best location is elevated, such as wall mounted or on the top of a cubicle, at the center of your wireless coverage area, and within line of sight of all the mobile devices.2. Lift the antennae on either side so that they are vertical.Figure 2-5 Basic Wireless Settings for 802.11b/bg/ng

MaxR-3210 Wireless-N Access Point User Manual10 Arada Systems Confidentialv1.1, Dec 20093. Connect an Ethernet cable from your MaxR-3210 Wireless Access Point to a LAN port on your router, switch, or hub. 4. Connect the power adapter to the wireless access point and plug the power adapter in to a power outlet. The PWR, LAN, and Wireless LAN lights and should light up. Verifying Wireless ConnectivityUsing a computer with an 802.11b/bg/ng wireless adapter with the correct wireless settings needed to connect to the MaxR-3210 (SSID, WEP/WPA, MAC ACL, etc.), verify connectivity by using a browser such as Mozilla Firefox or Internet Explorer to browse the Internet, or check for file and printer access on your network.The default SSID for the 802.11b/bg/ng wireless mode is ARADA_11g. The SSID of any wireless access adapters must match the SSID configured in the MaxR-3210 Single Band Wireless-N Access Point. If they do not match, no wireless connection will be made. Logging In Using the Default IP AddressAfter you install the MaxR-3210, log in to the Access Point to configure the basic settings and the wireless settings. The MaxR-3210 is set, by default, with the IP address of 192.168.0.237 with DHCP disabled.Note: By default, MaxR-3210 is set with the DHCP client disabled. If your network uses dynamic IP addresses, you must change this setting. To connect to the MaxR-3210 after the DHCP server on your network assigns it a new IP address, enter the Access Point name into your Web browser. The default Access Point name is aradaxxxxxx, where xxxxxx represents the last 6 bytes of the MAC address. The default name is printed on the bottom label of the MaxR-3210.Note: If you are unable to connect, see Chapter 5, “Troubleshooting and Debugging.”Note: The computer you are using to connect to the MaxR-3210 should be configured with an IP address that starts with 192.168.0.x and a Subnet Mask of 255.255.255.0.

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 11v1.1, Dec 2009To log in using the default IP Address:1. Open a Web browser such as Internet Explorer or Mozilla Firefox. 2. Connect to the MaxR-3210 by entering its default address of http://192.168.0.237 into your browser. The login screen displays. Enter admin for the user name and password for the password, both in lower case letters.3. Click Login. Your Web browser should automatically find the MaxR-3210 Wireless Access Point and display the home screen.Setting Basic IP Options The basic IP settings for your Access Point are entered on this screen. Most of the default settings will work in most cases. However, if your Access Point is part of a more complex LAN network, then modify the settings to meet the requirements of your network based on the explanation of the various fields.To configure the basic IP settings of your Access Point:1. Under Configuration, select IP, and then IP Settings. The IP Settings screen displays as shown in Figure 2-7 below.Figure 2-6 Connecting to the Access Point

MaxR-3210 Wireless-N Access Point User Manual12 Arada Systems Confidentialv1.1, Dec 20092. Enter the IP Address fields of the MaxR-3210. –DHCP Client. By default, the Dynamic Host Configuration Protocol (DHCP) client is disabled. If you have a DHCP server on your LAN and you enable DHCP, the wireless access point will get its IP address, subnet mask and default gateway settings automatically from the DHCP server on your network when you connect the MaxR-3210 to your LAN.–IP Address. Enter the IP Address of your Access Point.The default IP address is 192.168.0.237. To change it, enter an unused IP address from the address range used on your LAN; or enable DHCP.–IP Subnet Mask. The Access Point will automatically calculate the subnet mask based on the IP address that you assign. Otherwise, you can use 255.255.255.0 (the default) as the subnet mask. –Default Gateway. Enter the IP address of the gateway for your LAN. For more complex networks, enter the address of the router for the network segment to which the Access Point is connected.–Primary DNS Servers. The MaxR-3210 will use this IP address as the primary Domain Name Server used by stations on your LAN.Figure 2-7 Basic IP options

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 13v1.1, Dec 2009–Secondary DNS Servers. The MaxR-3210 will use this IP address as the secondary Domain Name Server used by stations on your LAN.–Network Intgrity Check. Check this box to enable the MaxR-3210 to validate that the upstream link is active before allowing wirelessassociations.If you set this option you must ensure your default gateway is configured.3. Click Apply to save your basic IP settings.Wireless SettingsThe following sections describe how to configure the wireless settings available in the 802.11b/bg/ng modes.Configuring 802.11b/bg/ng Wireless SettingsTo configure the wireless settings of your 802.11 b/bg/ng Access Point:1. From main menu under Configuration, select Wireless. The Wireless Settings screen of your 802.11 b/bg/ng Access Point displays, as shown in Figure 2-8 below.Figure 2-8 Configure wireless settings 802.11b/bg/ng

MaxR-3210 Wireless-N Access Point User Manual14 Arada Systems Confidentialv1.1, Dec 20092. Configure the Wireless LAN settings based on the following field descriptions:•Wireless Mode. Select the desired wireless operating mode. The default is 11ng. The options are: –11b – All 802.11b wireless stations can be used. (The 802.11g wireless stations can still be used if they can operate in 802.11b mode.)–11bg – Both 802.11b and 802.11g wireless stations can be supported.–11ng – All 11b, 11g, and 11ng wireless stations can be used. This is the default. If you select this option, then two additional options, Channel Width and Guard Interval, are displayed.•Turn Radio On. On by default, you can also turn off the radio to disable access through this device. This can be helpful for configuration, network tuning, or troubleshooting activities.•Wireless Network Name (SSID). This is the name of your wireless network. It is set to ARADA_11g for 802.11b/bg/ng.•Broadcast Wireless Network Name (SSID). If you disable broadcast of the SSID, only devices that have the correct SSID can connect. This nullifies the wireless network “discovery” feature of some products such as Windows XP, Vista and Unix systems but the data is still fully exposed to a determined snoop using specialized test equipment like wireless sniffers. Default is enabled.•Channel/Frequency. From the pull-down menu, select the channel you wish to use on your wireless LAN. The wireless channel in use will be between 1 to 11 for US and Canada, 1 to 13 for Europe and Australia. The default is channel Auto.It should not be necessary to change the wireless channel unless you experience interference (shown by lost connections and/or slow data transfers). Should this happen, you may need to experiment with different channels to see which is the best. Alternatively, you can select the Auto channel option for the AP to intelligently pick the channel with least interference. When selecting or changing channels, some points to bear in mind: – Access points use a fixed channel. You can select the channel used. This allows you to choose a channel which provides the least interference and best performance. In the USA and Canada, 11 channels are available Note: If you select one of these option and if other settings on this screen are disabled, then you must select the Turn Radio On radio button to enable available options on this screen.

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 15v1.1, Dec 2009– If using multiple access points, it is better if adjacent access points use different channels to reduce interference. The recommended channel spacing between adjacent access points is 5 channels (for example, use channels 1 and 6, or 6 and 11).– Wireless stations normally scan all channels, looking for an access point. If more than one access point can be used, the one with the strongest signal is used. This can only happen when the various access points are using the same SSID.•MCS Index/Data Rate. From the pull-down menu, select the available transmit data rate of the wireless network. Also, depending on the band selected, the set of rates will vary. The possible data rates supported are: •Data Rates for Channel Width=20MHz and Guard Interval=short (400ms): Best, 7.2 Mbps, 14.4 Mbps, 21.7 Mbps, 28.9 Mbps, 43.3 Mbps, 57.8 Mbps, 65 Mbps, 72.2 Mbps, 14.44 Mbps, 28.88 Mbps, 43.33 Mbps, 57.77 Mbps, 86.66 Mbps, 115.56 Mbps, 130 Mbps, 144.44 Mbps•Data Rates for Channel Width=20MHz and Guard Interval=long (800ms): Best, 6.5 Mbps, 13 Mbps, 19.5 Mbps, 26 Mbps, 39 Mbps, 52 Mbps, 58.5 Mbps, 65 Mbps, 13 Mbps, 26 Mbps, 39 Mbps, 52 Mbps, 78 Mbps, 104 Mbps, 117 Mbps, 130 Mbps•Data Rates for Channel Width=40MHz and Guard Interval=short: Best, 15 Mbps, 30 Mbps, 45 Mbps, 60 Mbps, 90 Mbps, 120 Mbps, 135 Mbps, 150 Mbps, 30 Mbps, 60 Mbps, 90 Mbps, 120 Mbps, 180 Mbps, 240 Mbps, 270 Mbps, 300 Mbps•Data Rates for Channel Width=40MHz and Guard Interval=long: Best, 13.5 Mbps, 27 Mbps, 40.5 Mbps, 54 Mbps, 81 Mbps, 108Mbps, 121.5 Mbps, 135 Mbps, 27 Mbps, 54 Mbps, 81 Mbps, 108Mbps, 162 Mbps, 216 Mbps, 243 Mbps, 270 Mbps•Channel Width. From the pull-down menu, select the desired channel width.• 20 MHz - This is the static, legacy mode. It gives the least throughput.• 40 MHz - This is the static, high-throughput mode. Legacy clients will not be able to connect in this mode.• 20/40 MHz - This is the dynamic, compatibility mode.•Guard Interval. From the pull-down menu, select the desired guard interval. The guard interval protects from interference from other transmissions. The default is Auto.•Output Power. From the pull-down menu, select the transmit power of the access point. The options are Full, Half, Quarter, Eighth, and Minimum. Decrease the transmit power if two or more APs are close together and use the same channel frequency. The default is Full. (The transmit power may vary depending on the local regulatory regulations. 3. Click Apply to save your 802.11b/bg/ng wireless settings.

MaxR-3210 Wireless-N Access Point User Manual16 Arada Systems Confidentialv1.1, Dec 2009Configuring Basic QoS SettingsWi-Fi Multimedia Support (WMM). Wireless Multimedia (WMM) is a subset of the 802.11e standard. WMM allows wireless traffic to have a range of priorities, depending on the type of data.Time-dependent information, such as video or audio, has a higher priority than normal traffic. For WMM to function correctly, Wireless clients must also support WMM.To configure basic wireless QoS settings for 11b/bg/ng:1. Under the Configuration tab, select Wireless from the main menu, select Basic, and then select QoS Settings from the left panel. The QoS Settings screen displays, as shown in Figure 2-9.2. Wi-FI Multimedia (WMM) is enabled by default. Select the Disable radio button to disable WMM support.3. WMM Power Save is enabled by default. Select the Disable radio button to disable WMM power save.4. Click Apply to save your settingsFigure 2-9 Basic QoS settings screen

MaxR-3210 Wireless-N Access Point User Manual20 Arada Systems Confidentialv1.1, Dec 2009•Authentication Settings. Configure the following settings:•Network Authentication. The MaxR-3210 Access Point is set by default as an open system with no authentication. When setting up Network Authentication, bear in mind the following:– If you are using Access Point mode, then all options are available. In bridge mode some options may be unavailable.– Not all wireless adapters support WPA or WPA2. Windows XP and Windows 2000 with Service Pack 3 do include the client software that supports WPA. However, client software is required on the client. Consult the product documentation for your wireless adapter and WPA or WPA2 client software for instructions on configuring WPA2 settings.You can configure the MaxR-3210 to use the types of network authentication shown in the table below.Table 2-1. Network Authentication TypesTypeaa. All options are available if using Access Point mode. In bridge modes some options may be unavailable.DescriptionOpen System Can be used with WEP encryption or no encryption.Shared Key You must use WEP encryption and enter at least one shared key. Legacy 802.1x You must configure the RADIUS Server Settings to use this option. WPA with RADIUS You must configure the RADIUS Server Settings to use this option.WPA2 with RADIUS (WPA2 is a later version of WPA.) Only select this if all clients support WPA2. If selected, you must use AES encryption and configure the RADIUS Server Settings. WPA and WPA2 with RADIUS This selection allows clients to use either WPA (with TKIP) or WPA2 (with AES). If selected, you must use TKIP + AES encryption and configure the RADIUS Server Settings.WPA-PSK You must use TKIP or TKIP + AES encryption and enter the WPA passphrase (Network key). WPA2-PSK(WPA2 is a later version of WPA )Only select this if all clients support WPA2. If selected, you must use AES or TKIP + AES encryption and enter the WPA passphrase (Network key). WPA-PSK and WPA2-PSK This selection allows clients to use either WPA (with TKIP) or WPA2 (with AES). If selected, you must use TKIP + AES encryption and enter the WPA passphrase (Network key).

MaxR-3210 Wireless-N Access Point User Manual22 Arada Systems Confidentialv1.1, Dec 2009SSID and WEP/WPA Settings Setup Form802.11b/bg/ng ConfigurationFor a new wireless network, print or copy this form and fill in the configuration parameters. For an existing wireless network, the person who set up or is responsible for the network will be able to provide this information. Be sure to set the Regulatory Domain correctly as the first step.•SSID: The Service Set Identification (SSID) identifies the wireless local area network. ARADA_11g is the default MaxR-3210 SSID. However, you may customize it by using up to 32 alphanumeric characters. Write your customized SSID on the line below. ___________________________________Note: The SSID in the Access Point is the SSID you configure in the wireless adapter card. All wireless nodes in the same network must be configured with the same SSID: • Authentication: Circle one: Open System or Shared Key. (Choose Shared Key for more security.)Note: If you select shared key, the other devices in the network will not connect unless they are set to Shared Key as well and have the same keys in the same positions as those in the MaxR-3210.• WEP Encryption Keys.Circle one: 64, 128, or 152 bits. (Enter all four keys for the Key Size chosen.)Key 1: ___________________________________ Key 2: ___________________________________ Key 3: ___________________________________ Key 4: ___________________________________ • WPA-PSK (Preshared Key)Record the WPA-PSK key. Key: ___________________________________ • WPA RADIUS Settings. For WPA, record the following settings for the primary and secondary RADIUS servers:Server Name/IP Address: Primary _________________ Secondary __________________ Port: ___________________________________ Shared Secret: ___________________________________

MaxR-3210 Wireless-N Access Point User Manual24 Arada Systems Confidentialv1.1, Dec 20093. Enter the following RADIUS Server settings:•Authentication Server. This configuration is required for authentication using a RADIUS Server.The IP Address, Port Number, and Shared Secret are required for communication with the Primary RADIUS Server. You can also configure a Secondary RADIUS Server to use, if the Primary RADIUS Server fails.–IP Address. The IP address of the RADIUS Server.–Port Number. The port number of the RADIUS Server. The default is 1812.–Shared Secret. This is shared between the Wireless Access Point and the RADIUS Server while authenticating the supplicant (wireless client). •Accounting Server. This configuration is required for accounting using a RADIUS Server. The IP Address, Port Number, and Shared Secret are required for communication with the Primary RADIUS Server. You can also configure a Secondary RADIUS Server to use if the Primary RADIUS Server fails.–IP Address. The IP address of the RADIUS Server.–Port Number. Port number of the RADIUS Server. The default: 1813 Figure 2-11 RADIUS server settings

MaxR-3210 Wireless-N Access Point User Manual28 Arada Systems Confidentialv1.1, Dec 20092. From the Data Encryption drop-down menu, select encryption strength (64 bits, 128 bits, or 152 bits).3. You manually or automatically program the four data encryption keys. These values must be identical on all PCs and Access Points in your network. Choose either:• Automatic – Enter a word or group of printable characters in the Passphrase box and click the Generate button. The four key boxes will be automatically populated with key values.• Manual – Enter the number of hexadecimal digits appropriate to the encryption strength: 10 digits for 64-bit, 26 digits for 128-bit and 32 digits for 152-bit (any combination of 0-9, a-f, or A-F)Select which of the four keys will be the default.4. Select the key to be used as the default key by checking the radio box. (Data transmissions are always encrypted using the default key.)5. Wireless Client Security Separation is disabled by default. If enabled, associated wireless clients will not be able to communicate with each other. (This feature is intended for hotspots and other public access situations.6. Click Apply to save your settings.Figure 2-14 Configure WEP Shared Key

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 29v1.1, Dec 2009Configuring WPA with RADIUSNot all wireless adapters support WPA. Furthermore, client software is required on the client. Windows XP and Windows 2000 with Service Pack 3 or above do include the client software that supports WPA. Nevertheless, the wireless adapter hardware and driver must also support WPA. Consult the product document for your wireless adapter and WPA client software for instructions on configuring WPA settings.To configure WPA, follow these steps:1. Under the Configuration tab, select Security on the main menu, select Advanced from the left-hand menu, and then select RADIUS Server Settings. The RADIUS Server Settings screen displays.2. Enter the RADIUS Server Settings as shown in “Configuring the RADIUS Server Settings” on page 2-23.3. Click Apply to save your RADIUS Server settings.Note: If you use a wireless computer to configure WEP settings, you will be disconnected when you click Apply. Reconfigure your wireless adapter to match the new settings or access the Access Point from a wired computer to make any further changes.

MaxR-3210 Wireless-N Access Point User Manual32 Arada Systems Confidentialv1.1, Dec 20095. From the Network Authentication drop-down menu, select WPA2 with RADIUS from the list. By default, Data Encryption will be set to AES.6. Wireless Client Security Separation is disabled by default. If enabled, associated wireless clients will not be able to communicate with each other. (This feature is intended for hotspots and other public access situations.7. Click Apply to save your settings.Configuring WPA and WPA2 with RADIUSNot all wireless adapters support WPA and WPA2. Client software is required on the client:• Windows XP and Windows 2000 with Service Pack 3, or above, do include the client software that supports WPA. The wireless adapter hardware and driver must also support WPA. • Service Pack 3 does not include the client software that supports WPA2. Make sure your client card supports WPA2. The wireless adapter hardware and driver must also support WPA2.Consult the product documentation for your wireless adapter; WPA client software for instructions on configuring WPA settings; and WPA2 client software for instructions on configuring WPA2 settings.Figure 2-17 Configure WPA and WPA2 with RADIUS

MaxR-3210 Wireless-N Access Point User Manual34 Arada Systems Confidentialv1.1, Dec 2009Configuring WPA-PSKNot all wireless adapters support WPA. Furthermore, client software is required on the client. Windows XP and Windows 2000 with Service Pack 3 or above include the client software that supports WPA. Nevertheless, the wireless adapter hardware and driver must also support WPA. Consult the product document for your wireless adapter and WPA client software for instructions on configuring WPA settings.Figure 2-18 Configure WPA-PSK

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 35v1.1, Dec 2009To configure WPA-PSK:1. From the Network Authentication drop-down menu, select WPA-PSK. By default, Data Encryption will be set to TKIP.2. Enter the preshared key passphrase (Network Key).3. Wireless Client Security Separation is disabled by default. If enabled, associated wireless clients will not be able to communicate with each other. (This feature is intended for hotspots and other public access situations.4. Click Apply to save your settings.Configuring WPA2-PSKNot all wireless adapters support WPA2. Furthermore, client software is required on the client. Make sure your client card supports WPA2. Consult the product document for your wireless adapter and WPA2 client software for instructions on configuring WPA2 settings.To configure WPA2-PSK:Figure 2-19 Configure WPA2-PSK

MaxR-3210 Wireless-N Access Point User Manual36 Arada Systems Confidentialv1.1, Dec 20091. From the Network Authentication drop-down menu, select WPA2-PSK from the list. By default, Data Encryption will be set to AES.2. Enter the preshared key passphrase (Network Key).3. Wireless Client Security Separation is disabled by default. If enabled, associated wireless clients will not be able to communicate with each other. (This feature is intended for hotspots and other public access situations.4. Click Apply to save your settings.Configuring WPA-PSK and WPA2-PSKNot all wireless adapters support WPA and WPA2. Client software is required on the client:• Windows XP and Windows 2000 with Service Pack 3 or above do include the client software that supports WPA. The wireless adapter hardware and driver must also support WPA. • Service Pack 3 does not include the client software that supports WPA2. Make sure your client card supports WPA2. The wireless adapter hardware and driver must also support WPA2.Consult the product documentation for your wireless adapter; WPA client software for instructions on configuring WPA settings; and WPA2 client software for instructions on configuring WPA2 settings

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 37v1.1, Dec 2009.To configure WPA-PSK and WPA2-PSK:1. From the Network Authentication drop-down menu, select WPA-PSK & WPA2-PSK. By default, Data Encryption will be set to TKIP+AES.2. Enter the WPA Passphrase (Network Key).3. Wireless Client Security Separation is disabled by default. If enabled, associated wireless clients will not be able to communicate with each other. (This feature is intended for hotspots and other public access situations.4. Click Apply to save your settings.Figure 2-20 Configure WPA-PSK and WPA2-PSK

MaxR-3210 Wireless-N Access Point User Manual38 Arada Systems Confidentialv1.1, Dec 2009Restricting Wireless Access by MAC AddressThe optional Access Control window lets you block the network access privilege of any specified stations through the MaxR-3210 Wireless Access Point. When you enable access control, the access point only accepts connections from clients on the selected access control list. This provides an additional layer of security.To restrict access based on MAC addresses:1. Log in to the MaxR-3210 using the default address of http://192.168.0.237, user name of admin and default password of password, or whatever LAN address and password you have set up.2. Under the Configuration tab, select Security on the main menu, select Advanced from the left panel, and then select MAC Authetication. The MAC Authetication screen displays.Note: If configuring the MaxR-3210 from a wireless computer whose MAC address is not in the access control list, if you select Turn Access Control On, you will lose your wireless connection when you click Apply. You must then access the Access Point from a wired computer or from a wireless computer that is on the access control list to make any further changes.

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 39v1.1, Dec 20093. Check the Turn Access Control On radio box to enable Access Control feature. 4. Select the desired Access Control Database options. The options are: •Local MAC Address Database – The Access Point will use the local MAC address table for Access Control. This is the default.•RADIUS MAC Address Database – The Access Point will use the MAC address table located on the external RADIUS server on the LAN for Access Control. If you choose this database, you must configure the RADIUS Server Settings first (see “Configuring the RADIUS Server Settings” on page 2-23).5. The Trusted Wireless Stations list shows any wireless stations you have entered. If you have not entered any wireless stations this list will be empty. To delete an existing entry, select it and then click Delete.6. Click Refresh to refresh the Available Wireless Stations list found in your area.7. Select the stations from the list of Available Wireless Stations found in your area, or enter the MAC address of a station to add a new station manually. (You can usually find the MAC address printed on the bottom of the wireless adapter.)Figure 2-21 Configure MAC authentication

MaxR-3210 Wireless-N Access Point User Manual40 Arada Systems Confidentialv1.1, Dec 20098. Click Add to add the wireless device to the Trusted Wireless Stations list. Repeat these steps for each additional device you want to add to the list.9. Click Apply to save your wireless access control list settings.Now, only devices on this list will be allowed to wirelessly connect to the MaxR-3210.

Arada Systems Confidential 1v1.1, Dec 2009Chapter 3ManagementThis chapter describes how to use the management features of your MaxR-3210 Single Band Wireless-N Access Point. To access these features, connect to the MaxR-3210 as described in “Logging In Using the Default IP Address” on page 2-10. Then select the category under either the Monitoring or Maintenance headings in the main menu of the browser interface.This chapter contains the following sections:1. “Remote Management2. “Remote Console3. “Upgrading the Wireless Access Point Software4. “Configuration File Management5. “Restoring the MaxR-3210 to the Factory Default Settings6. “Changing the Administrator Password7. “Enabling the SysLog Server8. “Using Activity Log Information9. “Viewing General Summary Information10. “Viewing Network Traffic Statistics11. “Viewing Available Wireless Station Statistics12. “Enabling Rogue AP Detection13. “Viewing Rogue AP Statistics14. “Packet CaptureRemote ManagementBoth the SNMP and Remote Console are enabled by default, which allows for remote management of the MaxR-3210 from a client running SNMP management software, as well as from a secure Telnet console.

MaxR-3210 Wireless-N Access Point User Manual2 Arada Systems Confidentialv1.1, Dec 2009To set up an SNMP management interface:1. Under the Maintenance tab, select Remote Management, and then select SNMP from the left sidebar. The SNMP screen displays, as shown in Figure 3-1 below: 2. Enter the following information in the SNMP fields:•SNMP: Enable SNMP to allow the SNMP network management software, such as HP OpenView, to manage the wireless access point via SNMPv1/v2 protocol. •Read-Only Community Name: The community string to allow the SNMP manager to read the wireless access point's MIB objects. The default is Public.•Read-Write Community Name: The community string to allow the SNMP manager to read and write the wireless access point's MIB objects. The default is Private.•Trap Community Name: The community string to allow the SNMP manager to send traps. The default is trap.•IP address to Receive Traps: The IP address of the SNMP manager to receive traps sent from the wireless access point.•Trap Port: The port number on which the SNMP Manager will receive traps. The default is 162/UDP.Figure 3-1 Configure SNMP settings

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 3v1.1, Dec 2009Remote ConsoleThe Remote Console configuration features are located under the Maintenance tab, Remote Management, and then under Remote Console. Enter the following information in the Remote Console screen, as shown in Figure 3-2:• Secure Shell (SSH): If set to Enable, the Wireless Access Point will only allow remote access via Secure Shell and Secure Telnet. The default is Enable. •Telnet: If set to Enable, the Wireless Access Point will only allow remote access via Telnet. The default is Disable.Using the Secure Telnet InterfaceThe MaxR-3210 includes a secure Telnet command line interface (CLI). You can access the CLI from a secure Telnet client over the Ethernet port or over the serial console port. Figure 3-2 Configure Remote ConsoleNote: You must use a secure Telnet client such as Absolute Telnet. Also, when you configure the client, use the SSH1, 3DES option. If you use the Telnet client to connect over the Ethernet port, use the IP address of the MaxR-3210 as the host name.

MaxR-3210 Wireless-N Access Point User Manual4 Arada Systems Confidentialv1.1, Dec 2009To use the CLI from a Console Port:1. Using the null-modem cable, connect a VT100/ANSI terminal or a workstation to the port labeled Console.If you attached a PC, Apple Macintosh, or UNIX workstation, start a secure terminal-emulation program.2. Configure the terminal-emulation program to use the following settings:• Baud rate: 9600 bps• Data bits: 8• Parity: none•Stop bit: 1• Flow control: noneThese settings appear below the connector on the back panel.3. Press Enter. The screen shown below in Figure 3-3 should appear.4. Enter the login name and password (admin and password are the defaults). After successful login, the <Access Point Name> prompt should appear. In this example, the prompt is arada74F35E. 5. Enter help to display the CLI command help.CLI CommandsThe CLI commands are listed in Appendix B, “Command Line Reference.”Figure 3-3

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 5v1.1, Dec 2009Upgrading the Wireless Access Point SoftwareThe software of the MaxR-3210 Wireless Access Point is stored in FLASH memory, and can be upgraded as new software is released by Arada Systems. Upgrade files can be downloaded from Arada Systems’ support web site.. The upgrade file can be sent to the wireless access point using your browser. You cannot perform the software upgrade from a computer that is connected to the MaxR-3210 Wireless Access Point with a wireless link. You must use a computer that is connected to the MaxR-3210 Wireless Access Point with a Ethernet cable.Note: The Web browser used to upload new firmware into the MaxR-3210 must support HTTP uploads, such as Microsoft Internet Explorer 6.0 or above or Mozilla 1.5 or above. Warning: When uploading software to the MaxR-3210 Wireless Access Point, it is important not to interrupt the Web browser by closing the window, clicking a link, or loading a new page. If the browser is interrupted, the upload may fail, corrupt the software, and render the MaxR-3210 completely inoperable.

MaxR-3210 Wireless-N Access Point User Manual6 Arada Systems Confidentialv1.1, Dec 2009The Web browser used to upload new firmware into the MaxR-3210 must support HTTP uploads, such as Microsoft Internet Explorer 6.0 or above, or Firefox 1.5 or above.To upgrade the MaxR-3210 firmware:1. Download the new software file from the Arada Systems’ support website, save it to your hard disk.2. Under the Maintenance tab, select Upgrade from the main menu, and then select Firmware Upgrade. The Firmware Upgrade screen displays as shown in Figure 3-4 above.3. Click Browse and browse to the location of the upgrade file.4. Click Apply.When the upload completes, your Access Point will automatically restart. The upgrade process typically takes about 2 minutes.Configuration File ManagementThe MaxR-3210 Wireless Access Point settings are stored in the Access Point in a configuration file. This file can be saved (backed up) to a user’s computer, retrieved (restored) from the user’s computer, or cleared to factory default settings.Figure 3-4 Firmware upgrade screen

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 7v1.1, Dec 2009Saving Your Configuration SettingsTo backup your configuration settings:Under the Maintenance tab on the main menu , select Upgrade, then select Backup Settings from the left sidebar to back up your current settings. The following screen displays: 1. Click Backup. Your browser will extract the configuration settings from the Access Point and prompt you for a location on your computer to store the file. 2. Give the file a meaningful name, such as MaxR-3210.cfg, and click Save.Restoring Saved SettingsTo restore your settings from a saved configuration file:Figure 3-5 Backup configuration settings

MaxR-3210 Wireless-N Access Point User Manual8 Arada Systems Confidentialv1.1, Dec 2009Under the Maintenance tab on the main menu, select Upgrade, then select Restore Settings from the sidebar to back up your current settings. The following screen displays: 1. Enter the full path to the file on your computer or click the Browse button to locate the file. 2. When you have located the file, click Restore to upload the file. After completing the upload, the MaxR-3210 will reboot automatically.Restoring the MaxR-3210 to the Factory Default SettingsIt is sometimes desirable to restore the Access Point to the factory default settings. This can be done by using the Restore Defaults option, which restores all factory settings.To access this function: 1. Under the Maintenance tab on the main menu, select Reset, and then select Restore Defaults from the sidebar. The Restore Defaults screen displays, as shown in Figure 3-7 below.Figure 3-6 Restore Configuration settings from file

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 9v1.1, Dec 20092. On the Restore Defaults screen, enable the Restore to factory default settings option by selecting the Yes radio button.3. Click Apply to reset to the factory default settings.After a restore, the Access Point password will be password, the default LAN IP address will be 192.168.0.237, and the access point name will reset to the name printed on the label on the bottom of the unit.To restore the factory default configuration settings without knowing the login password or IP address, you must use the Default Reset button on the rear panel of the Access Point. The reset button has two functions:•Reboot. When pressed and released, the Wireless Access Point will reboot (restart).•Reset to Factory Defaults. This button can also be used to clear all data and restore all settings to the factory default values.To clear all data and restore the factory default values:1. Power off the MaxR-3210.Figure 3-7 Restore to factory defaults

MaxR-3210 Wireless-N Access Point User Manual10 Arada Systems Confidentialv1.1, Dec 20092. Use something with a small point, such as a pen, hold the Reset button for 5 seconds while you Power On the MaxR-3210.3. Continue holding the Reset Button until the LEDs blink twice.4. Release the Reset Button. The factory default configuration has now been restored and the MaxR-3210 is ready for use.Changing the Administrator PasswordThe default password is password. You should change this password to a more secure password, since you cannot change the administrator login name.To change the Administrator password:1. Under the Maintenance tab on the main menu, select Password, and then select Change Password. The Change Password screen displays as shown in Figure 3-8 below.2. First enter the old password in the Current Password field. Figure 3-8 Change administrator password

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 11v1.1, Dec 20093. Then enter the new password twice—once in the New Password field and again in the Repeat New Password field.4. Click Apply to save your change.Enabling the SysLog ServerThe SysLog screen allows you to enable the SysLog option if you have a SysLog server on your LAN.To enable a SysLog server:1. Under the Configuration tab on the main menu, select System, then select the Advanced option, and select SysLog to view the screen shown in Figure 3-9.2. Enable SysLog – Enable this option if you have a SysLog server on your LAN. If enabled, you must enter the IP address of your SysLog server and the port number your SysLog server is configured to use. The default is Disabled.3. SysLog Server IP Address –The access point will send all the SysLog to the specified IP address if SysLog option is enabled.4. Port Number – The port number configured in the SysLog server on your LAN. Default is 514.Figure 3-9 Enable Syslog server

MaxR-3210 Wireless-N Access Point User Manual12 Arada Systems Confidentialv1.1, Dec 20095. Click Apply to save your Syslog settings.Using Activity Log InformationThe Activity Log screen displays the Access Point system activity.To view the Activity Log, under the Monitoring tab on the main menu, click Logs. The Activity Logs screen displays as shown in Figure 3-10 below.The Activity Log Window displays the Access Point system activity.Click Refresh to update the display, click Clear to clear the log content, or click Save As to save the log contents into a file on a disk drive.Viewing General Summary InformationThe System screen, under the Monitoring tab provides a summary of the current MaxR-3210 configuration settings, including current IP settings and current Wireless settings. This information is read only, so any changes must be made on other pages.To access the System screen:Figure 3-10 View activity logs

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 13v1.1, Dec 2009Under the Monitoring tab on the main menu, select System to view the System screen, shown in Figure 3-11 below. This screen shows the parameters listed in Table 3-1:Table 3-1. System Information FieldsField DescriptionAccess Point InformationAccess Point Name Indicates the NetBIOS name. The default name may be changed, if desired.Ethernet MAC Address Displays the Media Access Control address (MAC address) of the Access Point’s Ethernet port.Wireless MAC address for 2.4GHzDisplays the Media Access Control address (MAC address) of the Access Point’s wireless card when operating at 2.4GHzFirmware Version The version of the firmware currently installed.Current Time Displays the current system time of the access point.Current IP SettingsIP Address The IP address of the Access Point.Subnet Mask The subnet mask for IP address of the Access Point.Default Gateway The default gateway for the Access Point communication.DHCP Client Enabled indicates that the current IP address of the AP was obtained from a DHCP server on your network. Disabled indicated a static IP configuration.Current Wireless Settings for 802.11b/bg/ngOperating Mode Identifies the 802.11 operating mode of the MaxR-3210.Channel/Frequency Identifies the channel the wireless port is using. ‘Auto’ is the default channel setting.Rogue AP Detection Identifies whether the Rogue AP detection feature is enabled or disabled.

MaxR-3210 Wireless-N Access Point User Manual14 Arada Systems Confidentialv1.1, Dec 2009Viewing Network Traffic StatisticsThe Statistics screen displays information for both wired (LAN) and wireless (WLAN) interface network traffic. To access Statistics information:1. Under the Monitoring tab on the main menu, select Statistics. The Statistics screen displays, as shown in Figure 3-12 below. Figure 3-11 View system information

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 15v1.1, Dec 20092. Click Refresh to update the Statistics information for each interface. .Table 3-2, shown below, describes the information fields detailed on the Statistics screen.Figure 3-12 View network statisticsTable 3-2. Statistics FieldsField DescriptionWired EthernetPackets The number of packets sent and received since the MaxR-3210 was restarted.Bytes The number of bytes sent and received since the MaxR-3210 was restarted.Wireless 11b/bg/ngUnicast Packets The Unicast packets sent and received in 802.11n/g mode since the MaxR-3210 was restarted.Broadcast Packets The Broadcast packets sent and received in 802.11n/g mode since the MaxR-3210 was restarted.Multicast Packets The Multicast packets sent and received in 802.11n/g mode since the MaxR-3210 was restarted.

MaxR-3210 Wireless-N Access Point User Manual16 Arada Systems Confidentialv1.1, Dec 2009Viewing Available Wireless Station StatisticsThe Available Wireless Stations List (AWSL) contains a table of all IP devices associated with this Access Point in the wireless network defined by the Wireless Network Name (SSID). For each device, the table shows the MAC address, BSSID, SSID, Channel, Rate, State (whether the device is allowed to communicate with the Access Point or not), Type, AID, Mode, and Status.Total Packets The Wireless packets sent and received in 802.11n/g mode since the MaxR-3210 was restarted.Total Bytes The Wireless bytes sent and received in 802.11n/g mode since the MaxR-3210 was restarted.Note: A wireless network can include multiple wireless access points, all using the same network name (SSID). This enables extending the reach of the wireless network and allows users to roam from one access point to another, providing seamless network connectivity. Under these circumstances, be aware that only the stations associated with this access point will be presented in the Available Station List.Table 3-2. Statistics FieldsField Description

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 17v1.1, Dec 2009To view the Available Wireless Stations List:1. Under the Monitoring tab, select Wireless Stations on the main menu. The Available Wireless Stations list displays, as shown in Figure 3-13.2. Click Refresh to update the list.Enabling Rogue AP DetectionThe MaxR-3210 can detect rogue APs and wireless stations and show their details to the administrator.To enable Rogue AP Detection:Figure 3-13 Available Wireless Stations listTip: If the Access Point is rebooted, the table data is lost until the Access Point rediscovers the devices. To force the Access Point to look for associated devices, click the Refresh button.

MaxR-3210 Wireless-N Access Point User Manual18 Arada Systems Confidentialv1.1, Dec 20091. Under the Configuration tab on the main menu, select Security, select Advanced from the sidebar, and then select Rogue AP. The Rogue AP screen displays, as shown in Figure 3-8 below.2. Check the Turn Rogue AP Detection On radio box to enable rogue AP detection and click Apply.If you enable Rogue AP Detection, the AP continuously scans the wireless network and collects information about all APs heard on its channel.3. You can Import AP List from a File. See “Importing Rogue AP List from a File” on page 3-18 for more information.4. Under the Unknown AP List, click Refresh to discover the APs.5. Click Move to add any AP to the Known AP List. 6. Click Delete to remove an AP from the Known AP List.7. Click Apply to save your change.Importing Rogue AP List from a FileTo replace the existing AP list:Figure 3-14 Enable Rogue AP detection

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 19v1.1, Dec 20091. Create a text file that contains the MAC address of each known AP, separated by a space. The following example shows a list of six known APs that an administrator might upload to the AP:00:0c:41:d7:ee:a5 00:0f:b5:92:cd:49 00:12:17:70:85:3d 00:14:bf:ae:b1:e4 00:40:f4:f8:47:03 00:0c:41:d7:ee:b42. Select Replace to replace the existing list of known APs, or select Merge to add the new MAC addresses to the existing list.3. Click Browse and navigate to the location where you saved the text file.4. Select the file and click Open.5. Click Import to upload the list to the AP.To import the list from an existing file:1. Click Browse and navigate to the location where you saved the text file.2. Select the file and click Open.3. Click Import to upload the list to the AP.Viewing Rogue AP StatisticsThe MaxR-3210 can detect rogue APs and wireless stations and show a complete list of unknown or known APs to the administrator.To view the Rogue AP list:1. Under the Monitoring tab on the main menu, select Rogue AP. Select Unknown AP List.The following screen displays with a list of unknown APs:

MaxR-3210 Wireless-N Access Point User Manual20 Arada Systems Confidentialv1.1, Dec 20092. Click Refresh to refresh the list. 3. Click Save to export the list of unknown APs to a file. A window opens so you can browse to the location where you want to save the file.To view the list of known APs:Figure 3-15 Unknown APs list

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 21v1.1, Dec 20091. Under the Monitoring tab on the main menu, select Rogue AP. Select Known AP List.The following screen displays with a list of known APs:2. Click Refresh to refresh the list. 3. Click Save to export the list of known APs to a file. A window opens so you can browse to the location where you want to save the file.Packet CaptureThe packet capture option is available under the Monitoring > Packet Capture tab. Use this option for troubleshooting association problems. You can capture all packets transmitted and received by the AP and save them in pcap format for analysis by any standard sniffer tool such as WireShark or OmniPeek.Figure 3-16 Known APs list

MaxR-3210 Wireless-N Access Point User Manual22 Arada Systems Confidentialv1.1, Dec 2009The packet capture screen is shown below:Figure 3-17 Packet capture screen

Arada Systems Confidential 1v1.1, Dec 2009Chapter 4Advanced ConfigurationThis chapter describes how to configure the advanced features of your MaxR-3210 Single Band Wireless-N Access Point. The advanced configuration features are located under the Advanced sections of various sub-menus under Configuration and provide the following functions:•IP Settings. Using the Access Point as a DHCP server for wireless clients (“IP Settings for Wireless Clients).•Hotspot settings. Enabling HTTP redirect (“Hotspot Settings).•Wireless Settings: Configuring advanced wireless LAN parameters (“Configuring Advanced Wireless Settings).•Advanced QoS Settings: Configuring advanced QoS settings (“Configuring Advanced QoS Settings)•Access Point Settings: Enabling wireless bridging modes (“Enabling Wireless Bridging).IP Settings for Wireless ClientsYou can turn the MaxR-3210 into a DHCP Server for wireless clients for both DHCP-enabled wireless clients. The default advanced IP wireless settings usually work well. This feature is intended for use by a systems administrator. By default, this feature is not enabled.To use this Access Point as a DHCP server:1. From the main menu under Configuration, select IP, and then select DHCP Server Settings. The DHCP Server Settings screen displays (see Figure 4-1).2. DHCP Server is disabled by default. Select the Enable radio button to enable this wireless access point as a DHCP server.

MaxR-3210 Wireless-N Access Point User Manual2 Arada Systems Confidentialv1.1, Dec 2009.3. Configure the following TCP/IP configurations for using the MaxR-3210 as a DHCP Server for wireless clients. • DHCP Server: By default, the Dynamic Host Configuration Protocol (DHCP) server on the AP is disabled. If you enable it, all the wireless clients associated with the AP will get their IP addresses, subnet mask and default gateway settings automatically from the AP.• DHCP Server VLAN ID: All the stations that are part of the configured VLAN ID will get their IP addresses only from the AP.•Starting IP Address: Enter the starting IP address that can be assigned from the DHCP server on this Access Point. •Ending IP Address: Enter the Ending IP address that can be assigned from the DHCP server on this Access Point •Subnet Mask: The Access Point will assign the specified subnet mask to the connected wireless stations. •Gateway Address: The Access Point will assign this IP address as the default gateway for any traffic beyond the local network. •Primary DNS Server: The Access Point will assign this IP address as the primary Domain Name Server used by the connected wireless stations. Figure 4-1 DHCP server settings

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 3v1.1, Dec 2009•Secondary DNS Server: The Access Point will assign this IP address as the secondary Domain Name Server used by the connected wireless stations. •Primary WINS Server: The Access Point will assign this IP address as the primary WINS Server used by the connected wireless stations. •Secondary WINS Server: The Access Point will assign this IP address as the secondary WINS Server used by the connected wireless stations. •Lease: The lease time for the IP address assigned. The wireless client user is required to renew the IP address as soon as the lease is expired. 4. Click Apply to save your settings.Hotspot SettingsIf you want the Access Point to capture and redirect the first HTTP (TCP, port 80) request, use this feature to “capture” and redirect the HTTP request to the specified URL. For example, a hotel might want all wireless connections to go to its server to start a billing transaction.To set up a Hotspot server:1. From the main menu under Configuration, select System, then select Advanced. 2. From the sidebar, select Hotspot. The Hotspot screen displays, as shown in Figure 4-2., with the following fields:•HTTP Redirect: Enable HTTP Redirect..Figure 4-2 Hotspot settings

MaxR-3210 Wireless-N Access Point User Manual4 Arada Systems Confidentialv1.1, Dec 2009•Redirect URL: Enter the URL of the Web server where you wish to redirect HTTP (port 80) requests.3. Click Apply. All port 80 requests will now be redirected to the specified URL.Configuring Advanced Wireless SettingsThe Advanced option of the Wireless Settings menu is used to configure and enable various wireless LAN parameters for the 11b/bg/ng modes. The default wireless LAN parameters usually work well. However, you can use these settings to fine tune the overall performance of your Access Point for your environment.The Wireless Settings option of the Advanced menu is used to configure the Wireless LAN parameters. The default advanced wireless LAN parameter settings usually work well.Configuring 802.11b/bg/ng Advanced Wireless SettingsTo configure advanced Wireless Settings:1. Under the Configuration tab, select Wireless.2. From the sidebar, select Advanced, and then select Wireless Settings.

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 5v1.1, Dec 20093. The Advanced Wireless Settings screen displays, as shown in Figure 4-3., 4. Enter the appropriate information in the fields described below:•RTS Threshold (0 - 2347): Request to Send Threshold. The packet size that is used to determine if it should use the CSMA/CD (Carrier Sense Multiple Access with Collision Detection) mechanism or the CSMA/CA mechanism for packet transmission. With the CSMA/CD transmission mechanism, the transmitting station sends out the actual packet as soon as it has waited for the silence period. With the CSMA/CA transmission mechanism, the transmitting station sends out an RTS packet to the receiving station, and waits for the receiving station to send back a CTS (Clear to Send) packet before sending the actual packet data. The default is 2347.•Fragmentation Length (256 - 2346): This is the maximum packet size used for fragmentation. Packets larger than the size programmed in this field will be fragmented. The Fragmentation threshold value must be larger than the RTS threshold value. The default is 2346.•Beacon Interval (100 - 1000): The Beacon Interval. Specifies the interval time between 100ms and 1000ms for each beacon transmission, which allows the access point to synchronize the wireless network. The default is 100.Figure 4-3 Advanced Wireless Settings - 802.11b/bg/ng

MaxR-3210 Wireless-N Access Point User Manual6 Arada Systems Confidentialv1.1, Dec 2009•Aggregation Length (1024-65535) (11ng): The aggregation length defines the size of aggregated packets. Larger aggregation lengths may sometimes lead to better network performance. The default is 65535.•A-MPDU (11ng): Aggregated MAC Protocol Data Unit. Aggregates several MAC frames into a single large frame to achieve higher throughput. The default is enabled.•RIFS Transmission (11ng): Reduced Interframe Space. RIFS transmissions are shorter than other interframe spaces, and if enabled allow transmission of successive frames at different transmit powers. The default is disabled.•DTIM Interval: The Delivery Traffic Indication Message. Specifies the data beacon rate between 1 and 255. The default is 3. •Preamble Type (11b/bg only): A long transmit preamble may provide a more reliable connection or a slightly longer range. A short transmit preamble gives better performance. The Auto settings automatically handles both long and short preambles. The default is Auto.• Antenna: Not supported.•802.11d: Enable this option to include support for "additional regulatory domains" that are not in the current standard.• Max Wireless Clients: The number of wireless clients that can associate with the AP at one time. The default is 63.5. Click Apply to enable the Wireless Settings.Configuring Advanced QoS SettingsWireless Multimedia Extension (WME) or Wi-Fi Multimedia (WMM) is a subset of the 802.11e standard. WME allows wireless traffic to have a range of priorities, depending on the type of data. Time-dependent information, such as video or audio, has a higher priority than normal traffic. For WME to function correctly, Wireless clients must also support WME. Figure 4-4 shows the Quality of Service (QoS) screen. For most networks, the default QoS queue parameter settings work well.Quality of Service provides you with the ability to specify parameters on multiple queues for increased throughput and better performance of differentiated wireless traffic, like Voice-over-IP (VoIP), other types of audio, video, and streaming media, as well as traditional IP data.To configure advanced QoS settings, on the Configuration tab select Wireless, select Advanced, and then select QoS Settings. The QoS Settings screen dispalys:

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 7v1.1, Dec 2009The QoS options on the MaxR-3210 are as follows:•AP EDCA Parameters. Specify the AP EDCA (Enhanced Distributed Channel Access) parameters for different types of data transmitted from the MaxR-3210 Wireless Access Point to the wireless client.•Station EDCA Parameters. Specify the Station EDCA parameters for different types of data transmitted from the wireless client to the MaxR-3210 Wireless Access Point. If WMM is disabled, you cannot configure Station EDCA parameters.Table 4-1 describes the settings for QoS Queues.Figure 4-4 Advanced QoS settingsTable 4-1. QoS Queues and ParametersQoS Queue DescriptionData 0 (Voice) High priority queue, minimum delay. Time-sensitive data such as VoIP and streaming media are automatically sent to this queue.Data 1(Video) High priority queue, minimum delay. Time-sensitive video data is auto-matically sent to this queue.Data 2 (Best Effort) Medium priority queue, medium throughput and delay. Most traditional IP data is sent to this queue.

MaxR-3210 Wireless-N Access Point User Manual12 Arada Systems Confidentialv1.1, Dec 2009Configuring an MaxR-3210 as a Point-to-Point BridgeTo configure a point-to-point bridge as shown in Figure 4-8:1. Under the Configuration tab, select Wireless Bridge. Then, select Bridging. The Bridging screen displays (see Figure 4-5).2. Configure the MaxR-3210 (AP1) on LAN Segment 1 in Point-to-Point Bridge mode.3. Configure the MaxR-3210 (AP2) on LAN Segment 2 in Point-to-Point Bridge mode. AP1 must have AP2’s MAC address in its Remote MAC Address field and AP2 must have AP1’s MAC address in its Remote MAC Address field.4. Configure and verify the following parameters for both access points:• Verify that the LAN network configuration of the MaxR-3210 Wireless Access Points both are configured to operate in the same LAN network address range as the LAN devices• Both use the same ESSID, Channel, authentication mode, if any, and security settings if security is in use.5. Verify connectivity across the LAN 1 and LAN 2. A computer on either LAN segment should be able to connect to the Internet or share files and printers of any other PCs or servers connected to LAN Segment 1 or LAN Segment 2.Figure 4-8 Wireless point-to-point bridge setupLANSegment 1RouterAP inPoint-to-PointBridge ModeAP inPoint-to-PointBridge ModeLANSegment 2Hub or SwitchAP1ETHERNETRESET5-12V DCAP2ETHERNETRESET5-12V DC

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 13v1.1, Dec 20096. Click Apply to save your settings.Configuring an MaxR-3210 as a Point-to-Multi-Point Wireless BridgeTo configure a point-to-multi-point wireless bridge as shown in Figure 4-9:1. Under the Configuration tab, select Wireless Bridge. Then, select Bridging. The Bridging screen displays (see Figure 4-6).2. Configure the Operating Mode of the MaxR-3210 Wireless Access Points.• MaxR-3210 (AP1) on LAN Segment 1 in Point-to-Point Bridge mode with the Remote MAC Address of AP2.• Because it is in the central location, configure MaxR-3210 (AP2) on LAN Segment 2 in Point-to-Multi-Point Bridge mode. The MAC addresses of the adjacent APs are required in AP2.• Configure the MaxR-3210 (AP3) on LAN 3 in Point-to-Point Bridge mode with the Remote MAC Address of AP2.3. Verify the following parameters for all access points:• Verify that the LAN network configuration the MaxR-3210 Wireless Access Points are configured to operate in the same LAN network address range as the LAN devicesFigure 4-9 Wireless point-to-multipoint bridge setup'Master' AP inPoint-to-Multi-PointBridge ModeLANSegment 1192.168.0.1RouterAP inPoint-to-PointBridge ModeHub or SwitchLANSegment 3AP inPoint-to-PointBridge ModeLANSegment 2Hub or SwitchAP1ETHERNETRESET5-12VDCAP3ETHERNETRESET5-12VDCAP2ETHERNETRESET5-12VDC

MaxR-3210 Wireless-N Access Point User Manual14 Arada Systems Confidentialv1.1, Dec 2009• Only one access point is configured in Point-to-Multi-Point Bridge mode, and all the others are in Point-to-Point Bridge mode.• All access points must be on the same LAN. That is, all the APs LAN IP address must be in the same network.• If using DHCP, all MaxR-3210 Wireless Access Points should be set to “Obtain an IP address automatically (DHCP Client)” in the IP Address Source portion of the Basic IP Settings menu.• All MaxR-3210 Wireless Access Points use the same SSID, Channel, authentication mode, if any, and encryption in use.• All Point-to-Point Access Points must have the AP2 MAC address in its Remote AP MAC address field.4. Verify connectivity across the LANs. • A computer on any LAN segment should be able to connect to the Internet or share files and printers with any other PCs or servers connected to any of the three LAN segments.• Wireless stations will be able to connect to the MaxR-3210 Wireless Access Points in the illustration above. If you require wireless stations to access any LAN segment, you can add additional MaxR-3210 Wireless Access Points configured in Wireless Access Point mode to any LAN segment.5. Click Apply to save your settings.Note: You can extend this multi-point bridging by adding additional MaxR-3210s configured in Point-to-Point mode for each additional LAN segment.

Arada Systems Confidential 1v1.1, Dec 2009Chapter 5Troubleshooting and DebuggingThis chapter provides information about troubleshooting your MaxR-3210 Single Band Wireless-N Access Point. After each problem description, instructions are given to help you diagnose and solve the problem. For the common problems listed, go to the section indicated.• Is the MaxR-3210 on?Go to “Installing the MaxR-3210 Wireless Access Point” on page 2-4• Have I connected the Access Point correctly?Go to “Installing the MaxR-3210 Wireless Access Point” on page 2-4.• I cannot remember the Access Point’s configuration password.Go to “Changing the Administrator Password” on page 3-10.If you have trouble setting up your MaxR-3210, check the tips below.No lights are lit on the Access Point.It takes a few seconds for the power indicator to light up. Wait a minute and check the power light status on the access point.If the access point has no power.• Make sure the power cord is connected to the access point.• Make sure the power adapter is connected to a functioning power outlet. If it is in a power strip, make sure the power strip is turned on. If it is plugged directly into the wall, verify that it is not a switched outlet.• Make sure you are using the correct power adapter supplied with your access point.The Wireless LAN activity light does not light up.The access point antennas are not working.

MaxR-3210 Wireless-N Access Point User Manual2 Arada Systems Confidentialv1.1, Dec 2009• If the Wireless LAN activity light stays off, disconnect the adapter from its power source and then plug it in again. • Make sure the antennas are tightly connected to the MaxR-3210. • Contact ARADA technical support at support@aradasystems.com if the Wireless LAN activity light remains off.The LAN light is not lit.There is a hardware connection problem.Check these items:• Make sure the cable connectors are securely plugged in at the access point and the network device (hub, switch, or router). A switch, hub, or router must be installed between the access point and the Ethernet LAN or broadband modem.• LAN light does not light up if it is a 10 Mbps link. In such cases, the Lan activity light will still blink if there is activity. • Make sure the connected device is turned on.• Be sure the correct cable is used. Use a standard Category 5 Ethernet patch cable. If the network device has Auto Uplink™ (MDI/MDIX) ports, you can use either a crossover cable or a normal patch cable.I cannot access the Internet or the LAN with a wireless capable computer. There is a configuration problem. Check these items:• You may not have restarted the computer with the wireless adapter to have TCP/IP changes take effect. Restart the computer.• The computer with the wireless adapter may not have the correct TCP/IP settings to communicate with the network. Restart the computer and check that TCP/IP is set up properly for that network. The usual setting for Windows the Network Properties is set to “Obtain an IP address automatically.”• The access point’s default values may not work with your network. Check the access point default configuration against the configuration of other devices in your network.

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 3v1.1, Dec 2009I cannot connect to the MaxR-3210 to configure it.Check these items:• The MaxR-3210 is properly installed, LAN connections are OK, and it is powered on. Check that the LAN port LED is green to verify that the Ethernet connection is OK. • The default configuration of the MaxR-3210 is for a static IP address of 192.168.0.237 and a Mask of 255.255.255.0 with DHCP disabled. Make sure your network configuration settings are correct.• If you are using the NetBIOS name of the MaxR-3210 to connect, ensure that your computer and the MaxR-3210 are on the same network segment or that there is a WINS server on your network. • If your computer is set to “Obtain an IP Address automatically” (DHCP client), restart it.• If your computer uses a Fixed (Static) IP address, ensure that it is using an IP Address in the range of the MaxR-3210. The MaxR-3210 default IP Address is 192.168.0.237 and the default Subnet Mask is 255.255.255.0. If you are not sure about these settings, follow the instructions for “Installing the MaxR-3210 Wireless Access Point” on page 2-4.When I enter a URL or IP address I get a timeout error.A number of things could be causing this. Try the following troubleshooting steps.• Check whether other PCs work. If they do, ensure that your PCs TCP/IP settings are correct. If using a Fixed (Static) IP Address, check the Subnet Mask, Default Gateway, DNS, and IP Addresses.• If the PCs are configured correctly, but still not working, ensure that the MaxR-3210 is connected and turned on. Connect to it and check its settings. If you cannot connect to it, check the LAN and power connections.• If the MaxR-3210 is configured correctly, check your Internet connection (DSL/Cable modem etc.) to make sure that it is working correctly.•Try again.

MaxR-3210 Wireless-N Access Point User Manual4 Arada Systems Confidentialv1.1, Dec 2009Using the Reset Button to Restore Factory Default SettingsThe Reset button (see “Rear Panel” on page 1-5) has two functions:•Reboot. When pressed and released quickly, the MaxR-3210 will reboot (restart).•Reset to Factory Defaults. This button can also be used to clear ALL data and restore ALL settings to the factory default values.To clear all data and restore the factory default values:1. Power off the MaxR-3210 and power it back on.2. Use something with a small point, such as a pen, to press the Reset button in and hold it in for at least 5 seconds.3. Release the Reset button. The factory default configuration has now been restored, and the MaxR-3210 is ready for use.

Arada Systems Confidential 1v1.1, Dec 2009Appendix ADefault Settings and Technical SpecificationsThis appendix provides the factory default settings and technical specifications for the MaxR-3210 Single Band Wireless-N Access Point.Factory Default SettingsYou can use the reset button located on the front of your device to reset all settings to their factory defaults. This is called a hard reset. • To perform a hard reset, push and hold the reset button for approximately 5 seconds (until the TEST LED blinks rapidly). Your device will return to the factory configuration settings shown in Table A-1 below.• Pressing the reset button for a shorter period of time will simply cause your device to reboot.Table A-1. Access Point Default Configuration SettingsFeature DescriptionAP LoginUser Login URL 192.168.0.237User Name (case sensitive) admin Login Password (case sensitive) passwordEthernet ConnectionStatic IP Address 192.168.0.210Ethernet MAC Address See bottom label.Port Speed 10/100/1000Local Network (LAN)Lan IP 192.168.0.230Subnet Mask 255.255.255.0Gateway AddressDHCP Server Disabled

MaxR-3210 Wireless-N Access Point User Manual2 Arada Systems Confidentialv1.1, Dec 2009DHCP Client DisabledTime Zone USA-PacificTime Zone Adjusted for Daylight Saving Time DisabledSNMP Enabled, but Trap forwarding disabledSpanning Tree Protocol DisabledSecure Telnet EnabledWirelessOperating Mode Access PointAccess Point Name aradaxxxxxx where xxxxxx are the last 6 digits of the wireless access point MAC address.Wireless Communication Enabled11 b/bg/ng Wireless Network Name (SSID) ARADA_11gBroadcast Network Name SSID EnabledSecurity DisabledTransmission Speed Besta80211.g Radio Frequency Channel AutoOutput Power FullWireless Card Access List All wireless stations allowedWMM Support Enableda. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.Table A-1. Access Point Default Configuration SettingsFeature Description

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 3v1.1, Dec 2009Technical SpecificationsTable A-2. MaxR-3210 Technical SpecificationsParameter MaxR-3210 Single Band Wireless-N Access Point802.11g Data Rates 1, 2, 5.5, 11, 12, 18, 24, 36, 38, 54, & 108 Mbps (Auto-rate capable)802.11ng Data Rates Data Rates for Channel Width=20MHz and Guard Interval=short (400ms): Best, 7.2 Mbps, 14.4 Mbps, 21.7 Mbps, 28.9 Mbps, 43.3 Mbps, 57.8 Mbps, 65 Mbps, 72.2 Mbps, 14.44 Mbps, 28.88 Mbps, 43.33 Mbps, 57.77 Mbps, 86.66 Mbps, 115.56 Mbps, 130 Mbps, 144.44 MbpsData Rates for Channel Width=20MHz and Guard Interval=long (800ms): Best, 6.5 Mbps, 13 Mbps, 19.5 Mbps, 26 Mbps, 39 Mbps, 52 Mbps, 58.5 Mbps, 65 Mbps, 13 Mbps, 26 Mbps, 39 Mbps, 52 Mbps, 78 Mbps, 104 Mbps, 117 Mbps, 130 MbpsData Rates for Channel Width=40MHz and Guard Interval=short: Best, 15 Mbps, 30 Mbps, 45 Mbps, 60 Mbps, 90 Mbps, 120 Mbps, 135 Mbps, 150 Mbps, 30 Mbps, 60 Mbps, 90 Mbps, 120 Mbps, 180 Mbps, 240 Mbps, 270 Mbps, 300 MbpsData Rates for Channel Width=40MHz and Guard Interval=long: Best, 13.5 Mbps, 27 Mbps, 40.5 Mbps, 54 Mbps, 81 Mbps, 121.5 Mbps, 135 Mbps, 27 Mbps, 54 Mbps, 81 Mbps, 162 Mbps, 216 Mbps, 243 Mbps, 270 Mbps802.11b/bg/ng Operating Frequencies2.412 ~ 2.462 GHz (US) 2.457 ~ 2.462 GHz (Spain)2.412 ~ 2.484 GHz (Japan) 2.457 ~ 2.472 GHz (France)2.412 ~ 2.472 GHz (Europe ETSI)802.11 b/bg/ng Encryption 64-bits, 128- and 152-bits WEP, AES, TKIP data encryptionNetwork Management Web-based configuration and status monitoringMaximum Clients Limited by the amount of wireless network traffic generated by each node; maximum 64 supported.Status LEDs Power/Ethernet LAN/Wireless LAN/TestPower Adapter 12V DC, 1.5 AEnvironmental SpecificationsOperating temperature: 0 to 50° COperating humidity: 5-95%, non-condensing

MaxR-3210 Wireless-N Access Point User Manual4 Arada Systems Confidentialv1.1, Dec 2009

Arada Systems Confidential 1v1.1, Dec 2009Appendix BCommand Line ReferenceThe MaxR-3210 Single Band Wireless-N Access Point (AP) can be configured either through the command line interface (CLI), a Web browser, or an MIB browser. The CLI allows viewing and modification of the configuration from a terminal or PC through a telnet connection. Command Setskeyword Description-------------------------------------- ----------------------|-backup-configuration --backup configuration|-config> --configuration setting| |-apname --access point name| |-country --country/region| |-dhcp> --DHCP server| | |-dns-server --DNS server| | |-gateway --default gateway| | |-ip-address --IP range| | |-lease-time --lease time| | |-status --status| | |-subnet-mask --subnet mask| | |-wins-server --WINS server| || |-http-redirect --enable HTTP redirection | |-http-redirect-url --HTTP redirection URL| |-interface> --select wireless lan interface| | |-wlan> --wireless LAN interface setting| | | |-2.4GHz> --2.4 GHz wireless LAN interface setting| | | | |-aggregation-length --aggregated packet size| | | | |-ampdu --aggregated MAC Protocol Data Unit| | | | |-beacon-interval --wireless beacon period in TU(1024 us)| | | | |-channel --wireless channel (depends on countryand wireless mode)| | | | |-channelwidth --wireless channel width| | | | |-dtim-interval --wireless DTIM period in beacon interval| | | | |-extension-protection-spacing --wireless extension protection spacing| | | | |-fragmentation-length --wireless fragmentation threshold(even only)| | | | |-guardinterval --interval (from interference from other

MaxR-3210 Wireless-N Access Point User ManualArada Systems Confidential 7v1.1, Dec 2009| | |-syslog --enable syslog client| | |-syslog-server-ip --syslog server IP address| | |-syslog-server-port --syslog server port number| || |-radius>| | |-accounting-server-primary --primary accounting server| | |-accounting-server-primary-port --primary accounting server port| | |-accounting-server-primary-sharedsecret --primary accounting server shared secret| | |-accounting-server-secondary --secondary accounting server| | |-accounting-server-secondary-port --secondary accounting server port| | |-accounting-server-secondary-sharedsecret --secondary accounting server shared secret| | |-authentication-server-primary --primary authentication server| | |-authentication-server-primary-port --primary system accounting server shared secret| | |-authentication-server-primary-sharedsecret --primary authentication server shared secret| | |-authentication-server-secondary --secondary authentication server| | |-authentication-server-secondary-port --secondary authentication server port| | |-authentication-server-secondary-sharedsecret --secondary authentication server shared secret| || |-remote> --enable remote access via SSH | | |-ssh-port --SSH port| | |-sshd --SSH daemon| | |-telnet --enable remote access via Telnet| | | |-snmp> --SNMP setting| | |-description --SNMP system description| | |-read-community --SNMP ReadCommunity | | |-snmp-status --SNMP status| | |-trap-community --SNMP ReadCommunity | | |-trap-server --SNMP TrapServer IP address| | |-write-community --SNMP WriteCommunity| | | |-spanning-tree --enable spanning tree protocol| |-time> --time Setting| | |-custom-ntp-server --custom NTP server host name| | |-daylightsaving --daylight saving| | |-ntp-client --NTP client host name| | |-ntp-server --NTP server host name| | |-time-zone --time zone| | | |-vlan> --vlan settings| | |-management-vlan --vlan management id| | |-untagged-vlan --untagged vlan id

MaxR-3210 Wireless-N Access Point User Manual8 Arada Systems Confidentialv1.1, Dec 2009| | |-untagged-vlan-status --untagged vlan status| | | |-exit --logout from CLI|-file --|-firmware-upgrade --upload new system firmware file|-password --system password|-restore-configuration --restore system configuration|-restore-default-password --restore default system password|-show> --show system settings| |-configuration --show system configuration| |-interface> --show wireless lan interface| | |-eth> --ethernet interface| | | |-statistics --show ethernet statistics| | | | | |-wlan> --wlan interface settings| | | |-2.4GHz> --2.4GHz wlan interface settings| | | | |-configuration --interface configuration| | | | |-knownaplist --known access point list| | | | |-stationlist --station list| | | | |-statistics --interface statistics| | | | |-trusted-stationlist --trusted station list | | | | |-unknownaplist --unknown access point list| | | | | | | | | | | | | | |-log --system log | |-system --system setting

Index-1v1.1, Dec 2009IndexNumerics20 MHz 2-1520/40 MHz 2-1540 MHz 2-15802.11b/g/n 1-4, 2-13default SSID 2-10standards compliance 1-2802.11e 1-3, 2-16, 4-6802.11ndata encryption option, recommendation 2-3802.1Q 2-27802.1Q VLAN, support 1-2802.1x 2-20802.3af 1-3Aaccess controlMAC address filtering 1-3MAC authentication 2-38trusted wireless stations 1-3access control listMAC authentication 2-38access point modesecurity options 2-20access point name 2-5access point, more than one 2-15ACK 1-4activity log 3-12AES802.11n, recommended for 2-3with WPA2, with RADIUS 2-32with WPA2-PSK 2-36aggregation length 4-6aggregation, support for 1-4AID see association IDA-MPDU (Aggregation of MAC Protocol Data Units) 4-6antenna 4-62.4 GHz 1-5position 2-2, 2-9associated stationspresent in AWSL, only 3-16association IDauthentication server settingsIP address 2-24port number 2-24shared secret 2-24, 2-25auto or long preamble, support for 1-4Auto UplinkTM 1-4autosensing ethernet, support for 1-3autosensing, LAN interface 1-4available wireless station list (AWSL) 3-16available wireless stations list 2-39AWSL table fieldschannel 3-16MAC address 3-16mode 3-16rate 3-16SSID 3-16state 3-16status 3-16type 3-16wireless network name (SSID) 3-16Bback off 1-4Basic Service Set (BSS) 1-2Basic Service Set Identifier (BSSID) 1-2

MaxR-3210 Wireless-N Access Point User ManualIndex-2v1.1, Dec 2009beacon generation, support for 1-4beacon interval 4-5bridgenetwork authentication 2-20bridge mode wireless stationwireless point to point bridge 4-8wireless point-to-multi-point bridge 4-8BSSID 3-16CCategory 5 Ethernet cable 1-5change password 3-10channel autotesting connectivity 2-17channel auto selection 2-17channel interference 2-17channel spacing 2-3channel spacing, recommended 2-15channel, autoconfiguring channel/frequency 2-14channel, default 2-14CLIcommand set 3-4command line interface (CLI) 3-3configuration file 3-6backup or restore 3-7conventions, typographical 1-icoverage 2-2coverage area 1-1, 2-9CSMA/CA 4-5CSMA/CD (Carrier Sense Multiple Access with CollisionDetection) 4-5CTS (Clear to Send) 4-5Ddata encryption settings128 bits WEP 2-21152 bits WEP 2-2164 bits WEP 2-21AES 2-21none 2-21TKIP 2-21TKIP + AES 2-21data rates 802.11bgn 2-15default access point name 2-6default channel 2-14, 2-17default gateway, configure 2-12default IP address 2-4, 2-12default password 2-4default reset button 3-9default SSID 2-10default user name 2-4default wireless access point name 2-10DHCPpoint-to-multi-point bridging 4-14DHCP clientdefault setting 2-10DHCP client, configure 2-12DHCP client/serversupport 1-2DHCP serverconfigure 4-1on LAN 2-12on LAN, assigns IP address 2-10distributed coordinated function, support for 1-4documentation 2-5DTIM (Delivery Traffic Indication Message) interval 4-6dynamic encryption key generation, support 1-2dynamic IP address, configure 2-10dynamic per frame rekeying 2-3EEDCA (Enhanced Distributed Channel Access) 4-7EthernetRJ-45 port 1-6ethernet cable, connect 2-10Ffactory default settings 3-6

MaxR-3210 Wireless-N Access Point User ManualIndex-3v1.1, Dec 2009reset button 1-6, 5-4resetting 5-4restore 3-8table A-1firmwareupgrade 3-6FLASH 3-5formats, document 1-ifragmentation 4-5fragmentation threshold 4-5full-duplex 1-4Hhalf-duplex 1-4hidden mode, support for 1-3hotspotserver settings 4-3support for 1-3wIreless client security separation 2-28wireless client security separation 2-30, 2-32, 2-33, 2-35, 2-36, 2-37HTTP redirecthotspot settings 4-3Iinterference, channel settings 2-14interference, least 2-14interference, reduce 2-3, 2-15interference, sources 2-2IP addressconfigure 2-7, 2-12IP settings, configure 2-11Kkeys, use with WEP 2-21LLAN IP addressdefault 5-3latency 2-2legacy rates 2-3line of sight 2-9location 2-2, 2-9log in 2-11logs 3-11, 3-12MMAC addressaccess control list 2-38bridge mode wireless station 4-8wireless point-to-multi-point bridge 4-8MAC authenticationavailable wireless stations list 2-39MAC address database, local 2-39MAC address database, RADIUS 2-39trusted wireless stations 2-39turn access control on 2-39Management Information Base (MIB) management 1-2max users 1-1maximum packet size 4-5multiple access pointsplacement of 2-3multiple BSSIDs, support for 1-2multiple input, multiple output (MIMO), support for 1-4multi-point bridgingextend 4-14NNetBIOS name 2-6network authentication, types oflegacy 802.1x 2-20open system 2-20shared key 2-20WPA and WPA2 with RADIUS 2-20WPA with RADIUS 2-20WPA2 with RADIUS 2-20WPA2-PSK 2-20WPA-PSK 2-20WPA-PSK and WPA2-PSK 2-20network key

MaxR-3210 Wireless-N Access Point User ManualIndex-4v1.1, Dec 2009with WPA-PSK and WPA2-PSK 2-37WPA-PSK 2-35network statistics 3-14fields 3-15NTP client, configure 2-8NTP server, configure 2-8Ooperating frequency 1-2operating modes, supportedpoint-to-multi-point bridge. 1-3point-to-point bridge 1-3wireless access point 1-2Ppackage contents 1-5packet fragmentation, support for 1-4packet size 4-5passphrase, use with WEP 2-21, 2-28passwordchange 3-10performance degradationcauses of 2-2placement 2-2point-to-multi-point bridge 4-8configure 4-13point-to-point bridge 4-8configure 4-12point-to-point bridge modewireless point-to-multi-point bridge 4-8power adapter 1-6power consumption 2-2Power over Ethernet (PoE), support for 1-3preamble type 4-6preshared key passphraseWPA-PSK 2-35primary DNS server, configure 2-12profile namebridge mode wireless station 4-8wireless point-to-multi-point bridge 4-9QQoS queues 4-7QoS settings 2-16QoS settings, advancedAP EDCA parameters 4-7station EDCA parameters 4-7RRADIUS and certificate authentication, support 1-2RADIUS server, configure 2-23accounting server 2-24authentication server 2-24RADIUS server, configure first 2-18, 2-25range 1-1guidelines 2-2rear panel 1-5reboot 3-9reset button, using 5-4rebootinglosing previous state 3-17reception 2-2redirect HTTP 4-3redirect URLhotspot settings 4-4reduced inter frame spacing, support for 1-4remote consolesecure shell (SSH) 3-3Telnet 3-3request to send threshold 4-5reset button 3-9reset to factory defaults 3-9retransmission 1-4RIFSwireless settings 4-6roamingmultiple wireless access points 3-16roaming on same subnet, support for 1-4rogue AP detectionconfigure 3-17import rogue AP list from file 3-18

MaxR-3210 Wireless-N Access Point User ManualIndex-6v1.1, Dec 2009LAN activity 5-2power connection 5-1timeout error 5-3wireless Internet connection 5-2wireless LAN activity l 5-2trusted wireless stations listMAC authentication 2-39Uunauthorized access, secure from 2-1upgradeable firmware, support for 1-3VVLAN (802.1Q) 2-27VLAN IDDHCP server 4-2VLAN security profiles (VLAN ID), support for 1-4Voice-over-IP (VoIP) 4-6WWEPdata rates, provided by 2-3WEP, configuredata encryption keys 2-28data encryption strength 2-28network authentication type 2-27wireless client security separation 2-28Wi-Fi Multimedia (WMM) 4-6Wi-Fi Protected Access (WPA) 2-3wired equivalent privacy (WEP) 2-3wireless access pointsoftware 3-5wireless access point name 2-10wireless adapterverifying connectivity 2-10wireless adapter, settings 2-18wireless adaptersWPA support, restriction 2-29WPA2 support, restriction 2-31wireless bridging and repeating 4-8wireless channelchanging 2-14, 2-17wireless clientpoint-to-point bridge communication 4-8wireless client security separationhotspot setting 2-28wireless computer, configuring from 2-29wireless connectionlosing 2-38wireless connection, losing 2-18wireless connectivity, testing 2-17Wireless Multimedia (WMM) 2-16Wireless Multimedia (WMM), support for 1-3Wireless Multimedia Extension (WME) 4-6wireless network name (SSID) 2-26wireless point-to-multi-point bridge 4-8wireless point-to-point bridge 4-8wireless security optionsrestrict access based on MAC address. 2-3turn off broadcast of wireless network name (SSID) 2-3WEP, use 2-3WPA or WPA-PSK, use 2-3wireless settings 802.11b/bg/ng, advancedaggregation length 4-6A-MPDU 4-6antenna 4-6beacon interval 4-5DTIM interval 4-6fragmentation length 4-5preamble type 4-6RIFS transmission 4-6RTS threshold 4-5wireless settings 802.11bgnbroadcast wireless network name (SSID) 2-14channel width 2-15channel/frequency 2-14guard interval 2-15MCS index/data rate 2-15output power 2-15turn radio on 2-14wireless mode 2-14wireless network name (SSID) 2-14

MaxR-3210 Wireless-N Access Point User ManualIndex-7v1.1, Dec 2009wireless settings, basic 2-9wireless sniffer 2-3WPA and WPA2 with RADIUSrestiction with WPA and WPA2 2-32WPA and WPA2 with RADIUS, configure 2-33data encryption 2-33network authentication type 2-33wireless client security separation 2-33WPA preshared key passphrase, use with WPA-PSK 2-21WPA with RADIUS, configure 2-29data encription default 2-30network authentication type 2-30wireless client security separation 2-30WPA with RADIUS, restrictions 2-29WPA/WPA2use restrictions 2-20WPA/WPA2, support for 1-2WPA2 with RADIUS, configure 2-31data encryption default 2-32network authentication type 2-32wireless client security separation 2-32WPA2-PSK, configuredata encryption 2-36network authentication type 2-36preshared key passphrase 2-36restrictions using WPA2 2-35wireless client security separation 2-36WPA-PSK and WPA2-PSK preshared key authentication,support 1-2WPA-PSK and WPA2-PSK, configuredata encryption 2-37network authentication setting 2-37restrictions using WPA/WPA2 2-36wireless client security separation 2-37WPA passphrase (network key) 2-37WPA-PSK, configuredata encryption 2-35network authentication type 2-35preshared key passphrase 2-35restrictions for WPA 2-34wireless client security separation 2-35

MaxR-3210 Wireless-N Access Point User ManualIndex-8v1.1, Dec 2009

Navigation menu