Alvarion Technologies MICRO-25 Microbase station transceiver User Manual 4Motion System Manual
Alvarion Technologies Ltd. Microbase station transceiver 4Motion System Manual
Contents
- 1. Manual p1
- 2. Manual p2
- 3. Manual p3
- 4. Manual p4
- 5. Manual p5
Manual p5
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 548 System Manual3.9.9.7.2 Displaying Configuration Information for Neighbor BS Required C/N Level ParametersTo display configuration for the Neighbor BS Required C/N Level parameters, run the following command:npu# show nbr-requiredcnr bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to 16777215 StepSize 1)>]Specify the BS ID and the Neighbor BS ID (bs-id-lsb) if you want to display configuration for a particular Neighbor BS in a particular BS. For example, to display the Required C/N Level parameters of Neighbor BS 68000 in BS 66503, run the following command:npu# show nbr-requiredcnr bs 66053 bs-id-lsb 68000Do not specify these parameters if you want to view configuration information for all existing Neighbor BSs in all existing BSs. To display information for all Neighbor BSs in all BSs, run the following command:Display Format(for each existing Neighbor BS in each of the existing BSs if requested for all)BSIDLSB :<value>NeighborBSIDLSB :<value>SynchronizationIndicator :<value>EIRP :<value>Bandwidth(MHz) :<value>UplinkFeedbackZonePermutationBase :<value>PreambleIndex :<value>UCDConfigurationChangeCount :<value>DCDConfigurationChangeCount :<value>IsotropicrecpwrforInitrang :<value>CenterFrequency(MHz) :<value>PagingGroupId :<value>neighborStartRangeCodes :<value>NeighborBsDlDataMIMOMode :<value> Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-1.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 549 System Manualnpu# show nbr-requiredcnr bsCommand Syntaxnpu# show nbr-requiredcnr bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to 16777215 StepSize 1)> ]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Required C/N Level parameters of a specific Neighbor BS in a specific BS. Do not specify a value for this parameter if you want to display the Required C/N Level parameters of all Neighbor BSs in all BSs.Optional N/A 1-16777215bs-id-lsb <(1 to 16777215 StepSize 1)> The Neighbor BS ID.Specify a value for this parameter if you want to display the Required C/N Level parameters of a specific Neighbor BS in a specific BS. Do not specify a value for this parameter if you want to display the Required C/N Level parameters of all Neighbor BSs in all BSs.Optional N/A 1-16777215](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-2.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 550 System Manual3.9.9.7.3 Displaying Configuration Information for Neighbor BS Triggers ParametersTo display configuration information for Neighbor BS Triggers parameters, run the following command:npu# show nbr-triggers bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to 16777215 StepSize 1)> TrigName {scnReqCinrMin | scnReqRssiMin | scnReqRtdMax | scnRepCinrMaxNbs | scnRepRssiMaxNbs | scnRepCinrMargin | scnRepRssiMargin | scnRepRtdMax | scnRepCinrMinSbs | scnRepRssiMinSbs | hoReqCinrMaxNbs | hoReqRssiMaxNbs | hoReqCinrMargin | hoReqRssiMargin | hoReqRtdMax | hoReqCinrMinSbs | hoReqRssiMinSbs}]Specify the BS ID, Neighbor BS ID (bs-id-lsb) and Trigger name if you want to display configuration for a particular Trigger. For example, to display the scnReqCinrMin parameters of BS Neighbor 68000 in BS 66053, run the following command:npu# show nbr-triggers bs 66053 bs-id-lsb 68000 TrigName scnReqCinrMinDisplay Format(for each existing Neighbor BS in each of the existing BSs if requested for all)BSIDLSB :<value>NeighborBSIDLSB :<value>RequiredCNRforACK :<value>RequiredCNRforCQI :<value>RequiredCNRforCDMA :<value>RequiredCNRforQPSK1/2 :<value>RequiredCNRforQPSK3/4 :<value>RequiredCNRfor16QAM1/2 :<value>RequiredCNRfor16QAM3/4 :<value>RequiredCNRfor64QAM1/2 :<value>RequiredCNRfor64QAM2/3 :<value>RequiredCNRfor64QAM3/4 :<value>RequiredCNRfor64QAM5/6 :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-3.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 551 System ManualDo not specify these parameters if you want to view configuration information for all existing Neighbor BSs in all BSs. To display information for all Neighbor BSs in all BSs, run the following command:npu# show nbr-triggers bsCommand Syntaxnpu# show nbr-triggers bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to 16777215 StepSize 1)> TrigName {scnReqCinrMin | scnReqRssiMin | scnReqRtdMax | hoReqCinrMaxNbs | hoReqRssiMaxNbs | hoReqCinrMargin | hoReqRssiMargin | hoReqRtdMax | hoReqCinrMinSbs | hoReqRssiMinSbs} ]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display a specific Trigger in a specific Neighbor BS of a specific BS. Do not specify a value for this parameter if you want to display the Triggers of all Neighbor BSs in all BSs.Optional N/A 1-16777215bs-id-lsb <(1 to 16777215 StepSize 1)> The Neighbor BS ID.Specify a value for this parameter if you want to display a specific Trigger in a specific Neighbor BS of a specific BS. Do not specify a value for this parameter if you want to display the Triggers of all Neighbor BSs in all BSs.Optional N/A 1-16777215](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-4.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 552 System Manual3.9.9.7.4 Displaying Configuration Information for Neighbor BS Specific BS Triggers ParametersTo display configuration information for Neighbor BS Specific BS Triggers parameters, run the following command:npu# show nbr-specific bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to 16777215 StepSize 1)> TrigName {hoReqCinrMaxNbs | hoReqRssiMaxNbs | hoReqCinrMargin | hoReqRssiMargin} ]Specify the BS ID, Neighbor BS ID (bs-id-lsb) and Specific BS Trigger name if you want to display configuration for a particular Trigger. For example, to display the hoReqRssiMaxNbs parameters of BS Neighbor 68000 in BS 66053, run the following command:npu# show nbr-specific bs 66053 bs-id-lsb 68000 TrigName hoReqRssiMaxNbsTrigName {scnReqCinrMin | scnReqRssiMin | scnReqRtdMax | hoReqCinrMaxNbs | hoReqRssiMaxNbs | hoReqCinrMargin | hoReqRssiMargin | hoReqRtdMax | hoReqCinrMinSbs | hoReqRssiMinSbs} ]The Trigger name Specify only if you want to display a specific Trigger of a specific Neighbor BS in a specific BS. Do not specify if you want to display all Triggers parameters of all Neighbor BSs in all BSsscnReqCinrMinscnReqRssiMinscnReqRtdMaxhoReqCinrMaxNbshoReqRssiMaxNbshoReqCinrMarginhoReqRssiMarginhoReqRtdMaxhoReqCinrMinSbshoReqRssiMinSbs}Display Format(for a selected Trigger)BSIDLSB :<value>BSIDLSB :value>scnReqCinrMin :value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-5.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 553 System ManualDo not specify these parameters if you want to view configuration information for all existing Neighbor BSs in all BSs. To display information for all Neighbor BSs in all BSs, run the following command:npu# show nbr-triggers bsCommand Syntaxnpu# show nbr-specific bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to 16777215 StepSize 1)> TrigName {hoReqCinrMaxNbs | hoReqRssiMaxNbs | hoReqCinrMargin | hoReqRssiMargin} ]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display a specific Specific BS Trigger in a specific Neighbor BS of a specific BS. Do not specify a value for this parameter if you want to display the Specific BS Triggers of all Neighbor BSs in all BSs.Optional N/A 1-16777215](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-6.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 554 System Manual3.9.9.7.5 Displaying Configuration Information for All Neighbor BS ParametersTo display configuration for the all Neighbor BS parameters, run the following command:npu# show nbr-all bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to 16777215 StepSize 1)>]bs-id-lsb <(1 to 16777215 StepSize 1)> The Neighbor BS ID.Specify a value for this parameter if you want to display a specific Specific BS Trigger in a specific Neighbor BS of a specific BS. Do not specify a value for this parameter if you want to display the Specific BS Triggers of all Neighbor BSs in all BSs.Optional N/A 1-16777215TrigName {hoReqCinrMaxNbs | hoReqRssiMaxNbs | hoReqCinrMargin | hoReqRssiMargin} ]The Trigger name Specify only if you want to display a specific Specific BS Trigger of a specific Neighbor BS in a specific BS. Do not specify if you want to display all Specific BS Triggers parameters of all Neighbor BSs in all BSs{hoReqCinrMaxNbshoReqRssiMaxNbshoReqCinrMarginhoReqRssiMargin}Display Format(for a selected Trigger)BSIDLSB :<value>BSIDLSB :value>hoReqRssiMaxNbs :value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-7.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 555 System ManualSpecify the BS ID and the Neighbor BS ID (bs-id-lsb) if you want to display configuration for a particular Neighbor BS in a particular BS. For example, to display all parameters of Neighbor BS 68000 in BS 66503, run the following command:npu# show nbr-all bs 66053 bs-id-lsb 68000Do not specify these parameters if you want to view configuration information for all existing Neighbor BSs in all existing BSs. To display information for all Neighbor BSs in all BSs, run the following command:npu# show nbr-all bsCommand Syntaxnpu# show nbr-all bs [<(1 to 16777215 StepSize 1)> bs-id-lsb <(1 to 16777215 StepSize 1)> ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the parameters of a specific Neighbor BS in a specific BS. Do not specify a value for this parameter if you want to display the parameters of all Neighbor BSs in all BSs.Optional N/A 1-16777215bs-id-lsb <(1 to 16777215 StepSize 1)> The Neighbor BS ID.Specify a value for this parameter if you want to display the parameters of a specific Neighbor BS in a specific BS. Do not specify a value for this parameter if you want to display the parameters of all Neighbor BSs in all BSs.Optional N/A 1-16777215](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-8.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 556 System Manual3.9 .10 Managing the RF Frequency Para m e t e rAfter enabling the BS configuration mode, you can configure the RF frequency parameter (refer to Section 3.9.10.1).You can display configuration information for the RF frequency parameter of a selected or all existing BSs (refer to Section 3.9.10.2).3.9.10.1 Configuring the RF Frequency ParameterFrom the BS configuration mode, run the following command:npu(config-bs-66053)# rf [frequency <(2022.5 to 2217.5 StepSize 0.125) | (2302.5 to 2397.5 StepSize 0.125) | (2487.5 to 2687.5 StepSize 0.125) | (3302.5 to 3397.5 StepSize 0.125) | (3402.5 to 3597.5 StepSize 0.125) | (3602.5 to 3797.5 StepSize 0.125)>]Command ModesGlobal command modeTo configure the RF frequency parameter:Command Syntaxnpu(config-bs-66053)# rf [frequency <((2022.5 to 2217.5 StepSize 0.125) | (2302.5 to 2397.5 StepSize 0.125) | (2487.5 to 2687.5 StepSize 0.125) | (3302.5 to 3397.5 StepSize 0.125) | (3402.5 to 3597.5 StepSize 0.125) | (3602.5 to 3797.5 StepSize 0.125)>]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-9.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 557 System Manual3.9.10.2 Displaying Configuration Information for the RF Frequency ParameterTo display configuration information of the RF frequency parameter, run the following command:npu# show rf bs [<(1 to 16777215 StepSize 1)Specify the BS ID if you want to display information for a particular BS. For example, to display the RF frequency of BS 66053, run the following command:npu# show rf bs 66053Do not specify this parameter if you want to view information for all existing BSs. To display information for all BSs, run the following command:npu# show rf bs[frequency <(2022.5 to 2217.5 StepSize 0.125) | (2302.5 to 2397.5 StepSize 0.125) | (2487.5 to 2687.5 StepSize 0.125) | (3302.5 to 3397.5 StepSize 0.125) | (3402.5 to 3597.5 StepSize 0.125) | (3602.5 to 3797.5 StepSize 0.125)>]The center of the frequency band in which the BS will transmit, in MHz.Must be within the valid range of the relevant ODU.The indicated Possible Values are for a bandwidth of fiveMhz. For a different bandwidth, the actually valid values are from f1+1/2BW to f2-1/2BW, where f1 is the lowest frequency of the ODU’s radio band. Note that oDU23052360000N361by1Y0 (16) includes two bands: 2305-2320, 2345-2360 MHz.), f2 is the highest frequency of the ODU’s band, and BW is the configured bandwidth (see “Configuring the Baseband Bandwidth Parameter” on page 559). Mandatory N/A 2022.5 to 2217.5 in steps of 0.1252302.5 to 2397.5 in steps of 0.1252487.5 to 2687.5 in steps of 0.1253302.5 to 3397.5 in steps of 0.1253402.5 to 3597.5 in steps of 0.1253602.5 to 3797.5 in steps of 0.125Command Modesbs configuration modeIMPORTANTWhen creating a new BS, the mandatory frequency parameter must be configured.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-10.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 558 System Manual3.9 .11 Managing the Baseband Ba ndw idth Pa ra m e t e rAfter enabling the BS configuration mode, you can configure the Baseband bandwidth parameter (refer to Section 3.9.11.1).You can display configuration information for the Baseband bandwidth parameter of a selected or all existing BSs (refer to Section 3.9.11.2).Command Syntaxnpu# show rf bs [<(1 to 16777215 StepSize 1)Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the RF frequency parameter of a specific BS. Do not specify a value for this parameter if you want to display the RF frequency parameter of all BSs.Optional N/A 1-16777215Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>Frequency :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-11.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 559 System Manual3.9.11.1 Configuring the Baseband Bandwidth ParameterFrom the BS configuration mode, run the following command:npu(config-bs-66053)# baseband [bandwidth {fiveMHz | tenMHz | sevenMHz}]Note that the valid value ranges (and in some cases also default value) of certain parameters are affected by the value configured for the bandwidth parameter. If you change the bandwidth, verify that these parameters are configured properly:To configure the Baseband bandwidth parameter:IMPORTANTA bandwidth of 7 MHz (sevenMHz) is not applicable for ODUs in the 2.x GHz band.Command Syntaxnpu(config-bs-66053)# baseband [bandwidth {fiveMHz | tenMHz | sevenMHz} ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values[bandwidth {fiveMHz | tenMHz | sevenMHz} ]BS channel bandwidthMandatory N/A fiveMHztenMHzsevenMHz Command Modesbs configuration modeIMPORTANTWhen creating a new BS, the mandatory frequency parameter must be configured.Table ParametersRF (see Section 3.9.10.1) frequency](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-12.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 560 System Manual3.9.11.2 Displaying Configuration Information for the Baseband Bandwidth ParameterTo display configuration information of the Baseband bandwidth parameter, run the following command:npu# show baseband bs [<(1 to 16777215 StepSize 1)Specify the BS ID if you want to display information for a particular BS. For example, to display the Baseband bandwidth of BS 66053, run the following command:npu# show baseband bs 66053Do not specify this parameter if you want to view information for all existing BSs. To display information for all BSs, run the following command:npu# show baseband bsAirframe Structure, General (see Section 3.9.12.2.1)ul-dl-allocationAirframe Structure, Map Zone (see Section 3.9.12.2.2)majorgrpsAirframe Structure, Uplink Data Zone (see Section 3.9.12.2.6)subchannelsTriggers (see Section 3.9.7.1) triggers-scnreq-rtd-maxtriggers-horeq-rtd-maxCommand Syntaxnpu# show baseband bs [<(1 to 16777215 StepSize 1)Privilege Level1](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-13.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 561 System Manual3.9 .12 Managing Airframe Structure Pa ra meters1Enable the Airframe configuration mode (refer to Section 3.9.12.1)2You can now execute any of the following tasks:»Configure one or more of the Airframe parameters tables (refer to Section 3.9.12.2)»Restore the default values of parameters in one or more of the Airframe parameters tables (refer to Section 3.9.12.3)» Terminate the Airframe configuration mode (refer to Section 3.9.12.4)Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Baseband bandwidth parameter of a specific BS. Do not specify a value for this parameter if you want to display the Baseband bandwidth parameter of all BSs.Optional N/A 1-16777215Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>Bandwidth :<value>Command ModesGlobal command modeTo configure Airframe Structure parameters:](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-14.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 562 System ManualIn addition, you can, at any time, display configuration information for each of the Airframe parameters tables (refer to Section 3.9.12.5).3.9.12.1 Enabling the Airframe Configuration ModeTo configure the Airframe parameters, first enable the Airframe configuration mode. Run the following command to enable the Airframe configuration mode.npu(config-bs-66053)# airframeAfter enabling the Airframe configuration mode, you can execute any of the following tasks:Configure one or more of the Airframe parameters tables (refer to Section 3.9.12.2)Restore the default values of parameters in one or more of the Airframe parameters tables (refer to Section 3.9.12.3)After executing the above tasks, you can terminate the Airframe configuration mode (refer to Section 3.9.12.4) and return to the BS configuration mode.Note that for properly completing the Airframe configuration the apply command must be executed prior to exiting the Airframe configuration mode.3.9.12.2 Configuring Airframe ParametersAfter enabling the Airframe configuration mode you can configure the following parameters tables:General (refer to Section 3.9.12.2.1)Map Zone (refer to Section 3.9.12.2.2)Command Syntaxnpu(config-bs-66053)# airframePrivilege Level10Command Modesbs configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-15.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 563 System ManualDownlink Diversity (refer to Section 3.9.12.2.3)Uplink Feedback Zone (refer to Section 3.9.12.2.4)Downlink Data Zone (refer to Section 3.9.12.2.5)Uplink Data Zone (refer to Section 3.9.12.2.6)Mimo (refer to Section 3.9.12.2.7)3.9.12.2.1 Configuring Airframe General ParametersTo configure the Airframe General parameters, run the following command:npu(config-bs-66053-airframe)# general [cell-id <(0 to 31 StepSize 1)>] [preamble-grp <(1 to 2 StepSize 1)>] [segment <(0 to 2 StepSize 1)>] [frame-offset <zero|random>] [ul-duration <(3 to 7 StepSize 1 | 10 to 10 StepSize1)>] [nbr-beam-forming {yes | no} ]Neighbor BS Beam Forming (nbr-beam-forming): Applicable only for unit operating in MIMO Matrix A or B mode. The beam forming mechanism is based on symmetry in performance between uplink and down link. To compensate for possible differences due to HW of the ODU, a special low-level calibration signal is transmitted periodically in each link. During the time this calibration signal is transmitted all other radio links of the same BS and all its neighbors should not transmit, to reduce potential interference. The Beam Forming mechanism ensures that all neighboring BSs operating in Beam Forming mode will enter into silent mode when necessary. A unit operating in Matrix A or B mode should enter into silent mode when necessary (based on frame number information) only if it has neigboring BSs operating in Beam Forming mode.IMPORTANTAfter completing the Airframe configuration, do not forget to execute the apply command before exiting the Airframe configuration mode:npu(config-bs-66053-airframe)# applyIMPORTANTWhen creating a new BS, all mandatory Neighbor BS General parameters must be configured.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-16.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 564 System ManualCommand Syntaxnpu(config-bs-66053-airframe)# general [cell-id <(0 to 31 StepSize 1)> ] [preamble-grp <(1 to 2 StepSize 1)>] [segment <(0 to 2 StepSize 1)> ] [frame-offset <zero|random)> ] [ul-duration <(3 to 7 StepSize 1 | 10 to 10 StepSize1)> ] [nbr-beam-forming {yes | no} ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values[cell-id <(0 to 31 StepSize 1)> ]The Cell ID (IDCell) used for preamble selection. Mandatory when creating a new BS.N/A 0 - 31[preamble-grp <(1 to 2 StepSize 1)>]The preamble group. A value of 2 is available only for the following combinations of segment and cell-id values:segment=0, cell-id=0, 3, 6, 9, 12, 15.segment=1, cell-id=1, 4, 7, 10, 13, 16.segment=2, cell-id=2, 5, 8, 11, 14, 17.Optional 1 1 - 2[segment <(0 to 2 StepSize 1)> ]The segment (BS) number in a three sector BS (0-2). This number influences the preamble selection and the major group used for the FDC transmission.Mandatory when creating a new BS.N/A 0 - 2[frame-offset <zero|random> ]Controls the offset applied between the internal frame count and the reported frame number. If random is selected, the AU will choose a random number between 0 to 15.Mandatory when creating a new BS.zero zero (0)random](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-17.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 565 System Manual3.9.12.2.2 Configuring Airframe Map Zone ParametersTo configure the Airframe Map Zone parameters, run the following command:npu(config-bs-66053-airframe)# mapzone [size <(-1 to -1 StepSize 1) | (2 to 16 StepSize 2)>] [majorgrps <hex-string>] [repetition <(1 to 1 StepSize 1) | (2 to 6 StepSize 2)>] [RCID-Usage {enable | disable} ]Each transmitted MAP includes allocations for each MS it served, using the MS’s CID for identifying each MS. The original CID includes 16 bits, which is significantly more than practically needed since a maximum of 500 MSs can be served by each BS. To reduce overhead, a smaller number of bits can be used, based on RCID (Reduced CID) defined in the standard. This mechanism can be used only if all MSs served by the BS support RCID. When enabled, CIDs of either 7 or 11 bits will be dynamically used, according to the current number of MS served at each given moment.[ul-duration <(3 to 7 StepSize 1 | 10 to 10 StepSize1)> ]The total duration of the uplink in a frame, in slots. (one slot equals 3 symbols).The range is 4-7 or 10 for bandwidth = 5 or 10MHz, 3-5 or 7 for bandwidth = 7MHz. To avoid BS-BS interference, the ul-duration must be identical in all BSs in a geographical region.Mandatory when creating a new BS.N/A 3 - 7, 10[nbr-beam-forming {yes | no} ]Applicable only for BSs using MIMO MatrixAorB mode. Indicates whether any of the neighboring BSs operates in beamForming mode.Optional no yesnoCommand Modesbs airframe configuration mode IMPORTANTWhen creating a new BS, the mandatory Airframe Map Zone majorgrps parameter must be configured.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-18.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 566 System ManualCommand Syntaxnpu(config-bs-66053-airframe)# mapzone [size <(-1 to -1 StepSize 1) | (2 to 16 StepSize 2)> ] [majorgrps <hex-string>] [repetition <(1 to 1 StepSize 1) | (2 to 6 StepSize 2)> ] [RCID-Usage {enable | disable} ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Valuessize <(-1 to -1 StepSize 1) | (2 to 16 StepSize 2)>The map zone size in symbols. A value of "-1" means the map zone size will be dynamic.Optional 6 -1, 2, 4, 6, 8, 10, 12, 14, 16.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-19.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 567 System Manualmajorgrps <hex-string>The Major groups allocated to the BS for maps transmission.Two hexadecimal numbers representing 8 bits numbered 0 to 7 (left to right). Bits 0 to 5 indicate whether Subchannel Groups 0 to 5 (respectively) are allocated. Bit 6 and 7 are set to 0.If BW=5 MHz, bits 1, 3 and 5 are not relevant ("don't care"). The value must be set to A8.For BW=7/10 MHz with Reuse 1, bits 0 to 5 must be set. The value must be set to fc.For BW=7/10 MHz with Reuse 3: If segment (see Section 3.9.12.2.1) = 0, then bits #0 and 1 should be set. The value must be set to c0. If segment = 1, then bits #2 and 3 should be set. The value must be set to 30. If segment = 2, then bits #4 and 5 should be set. The value must be set to 0c.Mandatory when creating a new BS.N/A a string of two hexadecimal numbers.repetition <(1 to 1 StepSize 1) | (2 to 6 StepSize 2)>The basic repetition used in the transmission of the maps using QPSK 1/2 (1 means no repetitions).Optional 6 1, 2, 4, 6RCID-Usage {enable | disable}Indicates whether RCID should be used,Optional disable enabledisableCommand Modesbs airframe configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-20.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 568 System Manual3.9.12.2.3 Configuring the Airframe Downlink Diversity Mode ParameterThe system supports the following operation modes in the downlink:MIMO Matrix A or BBeam FormingIn MIMO Matrix A or B mode the system can use either MIMO Matrix A or Matrix B. The selection between Matrix A and Matrix B is performed automatically for each MS according to link conditions and supported MS capabilities.MIMO Matrix A for Coverage Gain: In configuration with multiple transmit/receive antennas, a single data stream is transmitted in parallel over multiple paths. A mathematical algorithm known as Space Time Codes (STC) is used to encode the data streams to make them orthogonal to each other. This improves the signal to noise ratio at the receiver side, resulting in increased range and better throughput for subscribers that are difficult to reach (e.g. deep indoors).MIMO Matrix B for Increased Capacity: This flavor of MIMO, also known as Spatial Multiplexing MIMO (SM-MIMO), sends an independent data stream over each antenna. Thus, in case signal conditions are good, the data rate is increased and in excellent conditions may be doubled.Beam Forming mode is applicable only for 4x4 configurations (4-channels AU, 2x2 or 4x2 ODUs that support beam forming). The system learns the signals received from each MS in each of the antennas, and adapt the transmitted signals accordingly by sending the same data into radio signals at specific relative phases, Beamforming creates a narrower antenna beam than that generated by a baseline fixed-beam antenna, with the beam acting as a powerful adaptive directional antenna. The signal with its transmitted energy is electronically formed and directed to a particular subscriber, resulting in higher downlink gain for data, greater downlink throughput and lower interference.To configure the Airframe Downlink Diversity mode parameter, run the following command:npu(config-bs-66053-airframe)# dldiversity [mode < matrixAorB | beamForming>]IMPORTANTWhen creating a new BS, the Airframe Downlink Diversity mode parameter must be configured (even if configured to the default value).](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-21.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 569 System Manual3.9.12.2.4 Configuring Airframe Uplink Feedback Zone ParameterTo configure the Airframe Uplink Feedback Zone parameter, run the following command:npu(config-bs-66053-airframe)# ulfeedbackzone permbase <(0 to 69 StepSize 1)>Command Syntaxnpu(config-bs-66053-airframe)# dldiveraity [mode <matrixAorB | beamForming>]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Valuesmode <matrixAorB |beamForming>The diversity mode used in downlink transmissions.beamForming is not applicable for 2-channels AU.Optional matrixA0rB matrixAorBbeamFormingCommand Modesbs airframe configuration mode IMPORTANTWhen creating a new BS, the Airframe Structure Uplink Feedback Zone mandatory permbase parameter must be configured.Command Syntaxnpu(config-bs-66053-airframe)# ulfeedbackzone permbase <(0 to 69 StepSize 1)>Privilege Level10](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-22.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 570 System Manual3.9.12.2.5 Configuring Airframe Downlink Data Zone ParameterTo configure the Airframe Downlink Data Zone parameter, run the following command:npu(config-bs-66053-airframe)# dldatazone permbase <(0 to 31 StepSize 1)>Syntax Description Parameter Description Presence Default ValuePossible Values[permbase <(0 to 69 StepSize 1)> ]The permutation base used in the feedback zoneMandatory when creating a new BS.N/A 0 - 69Command Modesbs airframe configuration mode IMPORTANTWhen creating a new BS, the Airframe Uplink Feedback Zone mandatory permbase parameter must be configured.Command Syntaxnpu(config-bs-66053-airframe)# dldatazone permbase <(0 to 31 StepSize 1)>Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values[permbase <(0 to 31 StepSize 1)> ]The permutation base used in the downlink data zoneMandatory when creating a new BS.N/A 0 - 31Command Modesbs airframe configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-23.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 571 System Manual3.9.12.2.6 Configuring Airframe Uplink Data Zone ParameterTo configure the Airframe Uplink Data Zone parameter, run the following command:npu(config-bs-66053-airframe)# uldatazone permbase <(0 to 69 StepSize 1)> 3.9.12.2.7 Configuring Airframe MIMO ParametersThe DL MIMO feature provides a TX diversity gain or, when physical conditions allow, data rate gain (double rate).The gain is allowed thanks to two or four transmitting antennas at the BS side, two receiving antennas at the MS side, and encoding/decoding capabilities of both MS and BS.TX diversity gain is achieved when MS works at matrix A/STC, space time coding, AKA STTD (vertical encoding) mode.IMPORTANTWhen creating a new BS, the Airframe Structure Uplink Data Zone mandatory permbase parameter must be configured.Command Syntaxnpu(config-bs-66053-airframe)# uldatazone permbase <(0 to 69 StepSize 1)> Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values[permbase <(0 to 69 StepSize 1)> ]The permutation base used in the uplink datazoneMandatory when creating a new BS0 to 69 in steps of 1Command Modesbs airframe configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-24.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 572 System ManualData rate gain is achieved when MS works at matrix B/SM, spatial multiplexing MIMO mode. It is assumed that either all MSs support MIMO (not necessary both modes) or all MSs don't support MIMO (SIMO support only).The DL MIMO feature influences several system elements such as frame structure, rate adaptation and feedback zone.To configure the Airframe MIMO parameters, run the following command:npu(config-bs-66053-airframe)# mimo [first-zone-min-size <(-1 to -1 StepSize 1) | (2 to 34 StepSize 2)> ] [first-zone-max-size <(-1 to -1 StepSize 1) | (2 to 34 StepSize 2)> ] [max-map-size <(-1 to -1 StepSize 1) | (10 to 300 StepSize 10)> ] Command Syntaxnpu(config-bs-66053-airframe)# mimo [first-zone-min-size <(-1 to -1 StepSize 1) | (2 to 34 StepSize 2)> ] [first-zone-max-size <(-1 to -1 StepSize 1) | (2 to 34 StepSize 2)> ] [max-map-size <(-1 to -1 StepSize 1) | (10 to 300 StepSize 10)> ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-25.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 573 System ManualRecommended values for First Zone Minimum Size and Maximum Size:[first-zone-min-size <(-1 to -1 StepSize 1) | (2 to 34 StepSize 2)> ]Determines the initial size (in OFDMA symbols) of the first zone. When reuse 3 is used within first zone, this parameter should be equal across all BSs within deployment.See recommended values in Table 3-31 below. Other values should be avoided.In the current release this is the actual size of the first zone.For reuse 1 the default (no limitation) can be used-the actual size will be set dynamically according to the configuration. For reuse 3 a specific value must be configured.Optional -1 (no limitation)-1 (no limitation) or 2xN where N=1 to 17.[first-zone-max-size <(-1 to -1 StepSize 1) | (2 to 34 StepSize 2)> ]Maximum size (in OFDMA symbols) for first zone. Used mainly for performance control capability within frame.Cannot be lower than first-zone-min-size.In the current release the value of this parameter is ignored First Zone size is defined only by first-zone-min-size.Optional -1 (no limitation)-1 (no limitation) or 2xN where N=1 to 17.[max-map-size <(-1 to -1 StepSize 1) | (10 to 300 StepSize 10)> ]Limits the maximum size of maps (in slots)Optional -1 (no limitation)-1 (no limitation) or 10 to 300 in steps of 10.Command Modesbs airframe configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-26.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 574 System Manual* First Zone Scheme is being determined by the selected Map Major Groups:For 7/10 MHz Full Loading means all Major Groups (0-5) are selected.For 5MHz Full Loading means that all relevant Major Groups (0, 2, 4) are selected.For First Zone Maximum Size the values are:If First Zone Minimum Size is set to No Limitations, the value range for Maximum Size is the same as for Minimum Size.Else, the value range is No Limitations or First Zone Minimum Size+2N, up to a maximum of Y as defined below.Table 3-31: First Zone Minimum Size Recommended Value RangeBandwidth (MHz)First Zone Scheme*Basic Map Repetition Minimum Size (symbols) (up to a maximum of Y as defined below)7/10 Full Loading 6 No Limitation or 8+2N4 No Limitation or 6+2N2 No Limitation or 4+2N1 No Limitation or 4+2NReuse 1/3 6 N/A (non trivial configuration)48+2N26+2N16+2N5 MHz Full Loading 6 N/A (non trivial configuration)4 No Limitation or 8+2N2 No Limitation or 6+2N1 No Limitation or 4+2NReuse 1/3 6 N/A (non trivial configuration)4 N/A (non trivial configuration)2 N/A (non trivial configuration)1 N/A (non trivial configuration)](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-27.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 575 System ManualThe value of Y that sets the upper limit for the Minimum and Maximum Size parameters depends on the Maximum Cell Radius and Total Uplink Duration parameters, using the following formula:Y=A-3*(Total Uplink Duration)-(Extra TTG), where A=46 for BW of 5 or 10 MHz, and 32 for BW of 7 MHz.3.9.12.3 Restoring Default Values for Airframe Configuration ParametersAfter enabling the Airframe configuration mode you can restore the default values for non-mandatory parameters in the following parameters tables:General (refer to Section 3.9.12.3.1)Map Zone (refer to Section 3.9.12.3.2)Downlink Diversity (refer to Section 3.9.12.3.3)Mimo (refer to Section 3.9.12.3.4)3.9.12.3.1 Restoring the Default Values of Airframe General ParametersTo restore one the Airframe non-mandatory General parameter to the default value, run the following command:npu(config-bs-66053-airframe)# no general [preamble-grp] [frame-offset ] [nbr-beam-forming ]Table 3-32: Calculating the Upper Limit Value (Y) for Minimum and Maximum SizeBandwidth (MHz) Maximum Cell Radius Total Uplink Duration (slots) Extra TTG (symbols)5/10 1, 2, 4, 8 4, 6 01, 2, 4, 8, 15, 23 5, 7 115, 23, 30 4, 6 230 5, 7 37 1, 2, 4, 8, 15, 23 4 01, 2, 4, 8, 15, 23, 30 3, 5 130 4 2](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-28.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 576 System Manual3.9.12.3.2 Restoring the Default Values of Airframe Map Zone ParametersTo restore one or all of the Airframe Map Zone non-mandatory parameters to their default values, run the following command:npu(config-bs-66053-airframe)# no mapzone [size] [repetition] [RCID-Usage ]You can restore only one parameter to the default value by specifying only that parameter. For example, to restore only the size parameter to the default value, run the following command:npu(config-bs-66053-airframe)# no mapzone sizeThe parameter will be restored to its default value, while the other parameters will remain unchanged.To restore all non-mandatory parameters to their default value, run the following command:npu(config-bs-66053-airframe)# no mapzoneNOTERefer to Section 3.9.12.2.1 for a description and default values of the parameter.Command Syntaxnpu(config-bs-66053-airframe)# no general [preamble-grp ] [frame-offset ] [nbr-beam-forming ]Privilege Level10Command Modesbs airframe configuration modeNOTERefer to Section 3.9.12.2.2 for a description and default values of these parameters.Command Syntaxnpu(config-bs-66053-airframe)# no mapzone [size ] [repetition ] [RCID-Usage ]](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-29.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 577 System Manual3.9.12.3.3 Restoring the Default Value of Airframe Downlink Diversity Mode ParameterTo restore the Airframe Downlink Diversity mode parameter to its default value, run the following command:npu(config-bs-66053-airframe)# no dldiversity modeSince the Downlink Diversity table contains a single parameter, it is sufficient to run the following command:npu(config-bs-66053-airframe)# no dldiversity3.9.12.3.4 Restoring the Default Values of Airframe MIMO ParametersTo restore one or all of the Airframe MIMO parameters to their default values, run the following command:npu(config-bs-66053-airframe)# no mimo [first-zone-min-size ] [first-zone-max-size ] [max-map-size ]To restore all MIMO parameters to their default values, run the following command:Privilege Level10Command Modesbs airframe configuration modeNOTERefer to Section 3.9.12.2.3 for a description and default values of these parameters.Command Syntaxnpu(config-bs-66053-airframe)# no dldiversity [mode ]Privilege Level10Command Modesbs airframe configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-30.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 578 System Manualnpu(config-bs-66053-airframe)# no mimo3.9.12.4 Terminating the Airframe Configuration ModeRun the following command to terminate the Airframe configuration mode:npu(config-bs-66053-airframe)# exit3.9.12.5 Displaying Configuration Information for Airframe ParametersYou can display the current configuration information for the following Airframe parameters tables:General (refer to Section 3.9.12.5.1)NOTERefer to Section 3.9.12.2.7 for a description and default values of these parameters.Command Syntaxnpu(config-bs-66053-airframe)# no mimo [first-zone-min-size ] [first-zone-max-size ] [max-map-size ]Privilege Level10Command Modesbs airframe configuration modeIMPORTANTDo not forget to execute the apply command before terminating the Airframe configuration mode: npu(config-bs-66053-airframe)# applyCommand Syntaxnpu(config-bs-66053-airframe)# exitPrivilege Level10Command Modesbs airframe configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-31.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 579 System ManualMap Zone (refer to Section 3.9.12.5.2)Downlink Diversity (refer to Section 3.9.12.5.3)Uplink Feedback Zone (refer to Section 3.9.12.5.4)Downlink Data Zone (refer to Section 3.9.12.5.5)Uplink Data Zone (refer to Section 3.9.12.5.6)Mimo (refer to Section 3.9.12.5.7)All (refer to Section 3.9.12.5.8)3.9.12.5.1 Displaying Configuration Information for Airframe General ParametersTo display configuration for the Airframe General parameters, run the following command:npu# show airframe-general bs [<(1 to 16777215 StepSize 1)>]Specify the BS ID if you want to display configuration for a particular BS. For example, to display the Airframe General parameters of BS 66503, run the following command:npu# show airframe-general bs 66053 Do not specify the BS ID if you want to view configuration information for all existing BSs. To display information for all BSs, run the following command:npu# show airframe-general bsCommand Syntaxnpu# show airframe-general bs [<(1 to 16777215 StepSize 1)> ]Privilege Level1](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-32.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 580 System Manual3.9.12.5.2 Displaying Configuration Information for Airframe Map Zone ParametersTo display configuration for the Airframe Map Zone parameters, run the following command:npu# show airframe-mapzone bs [<(1 to 16777215 StepSize 1)>]Specify the BS ID if you want to display configuration for a particular BS. For example, to display the Airframe Map Zone parameters of BS 66503, run the following command:npu# show airframe-mapzone bs 66053 Do not specify the BS ID if you want to view configuration information for all existing BSs. To display information for all BSs, run the following command:Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Airframe General parameters of a specific BS. Do not specify a value for this parameter if you want to display the Airframe General parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing Neighbor BS in each of the existing BSs if requested for all)BSIDLSB :<value>CellID :<value>PreambleGroup :<value>SegmentNumber :<value>FrameNumberOffset :<value>TotalUplinkDuration(slots) :<value>NeighbourBeamForming :<yes/no>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-33.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 581 System Manualnpu# show airframe-mapzone bs3.9.12.5.3 Displaying Configuration Information for Airframe Downlink Diversity ParametersTo display configuration for the Airframe Downlink Diversity parameters, run the following command:npu# show airframe-dldiversity bs [<(1 to 16777215 StepSize 1)>]Command Syntaxnpu# show airframe-mapzone bs [<(1 to 16777215 StepSize 1)> ]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Airframe Map Zone parameters of a specific BS. Do not specify a value for this parameter if you want to display the Airframe Map Zone parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing Neighbor BS in each of the existing BSs if requested for all)BSIDLSB :<value>MapZoneSize(symbols) :<value>MapMajorGroups :<value>BasicMapRepetitions :<value>RcidUsage :<enable/disable>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-34.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 582 System ManualSpecify the BS ID if you want to display configuration for a particular BS. For example, to display the Airframe Downlink Diversity parameters of BS 66503, run the following command:npu# show airframe-dldiversity bs 66053 Do not specify the BS ID if you want to view configuration information for all existing BSs. To display information for all BSs, run the following command:npu# show airframe-dldiversity bsCommand Syntaxnpu# show airframe-dldiversity bs [<(1 to 16777215 StepSize 1)> ]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Airframe Downlink Diversity parameters of a specific BS. Do not specify a value for this parameter if you want to display the Airframe Downlink Diversity parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing Neighbor BS in each of the existing BSs if requested for all)BSIDLSB :<value>DownlinkDataDiversityMode :<value>](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-35.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 583 System Manual3.9.12.5.4 Displaying Configuration Information for Airframe Uplink Feedback Zone ParametersTo display configuration for the Airframe Uplink Feedback Zone parameters, run the following command:npu# show airframe-ulfeedbackzone bs [<(1 to 16777215 StepSize 1)>]Specify the BS ID if you want to display configuration for a particular BS. For example, to display the Airframe Uplink Feedback Zone parameters of BS 66503, run the following command:npu# show airframe-ulfeedbackzone bs 66053 Do not specify the BS ID if you want to view configuration information for all existing BSs. To display information for all BSs, run the following command:npu# show airframe-ulfeedbackzone bsCommand ModesGlobal command modeCommand Syntaxnpu# show airframe-ulfeedbackzone bs [<(1 to 16777215 StepSize 1)> ]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Airframe Uplink Feedback Zone parameters of a specific BS. Do not specify a value for this parameter if you want to display the Airframe Uplink Feedback Zone parameters of all BSs.Optional N/A 1-16777215](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-36.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 584 System Manual3.9.12.5.5 Displaying Configuration Information for Airframe Downlink Data Zone ParametersTo display configuration for the Airframe Downlink Data Zone parameters, run the following command:npu# show airframe-dldatazone bs [<(1 to 16777215 StepSize 1)>]Specify the BS ID if you want to display configuration for a particular BS. For example, to display the Airframe Downlink Data Zone parameters of BS 66503, run the following command:npu# show airframe-dldatazone bs 66053 Do not specify the BS ID if you want to view configuration information for all existing BSs. To display information for all BSs, run the following command:npu# show airframe-dldatazone bsDisplay Format(for each existing Neighbor BS in each of the existing BSs if requested for all)BSIDLSB :<value>ULFeedbackZonePermutationBase :<value>Command ModesGlobal command modeCommand Syntaxnpu# show airframe-dldatazone bs [<(1 to 16777215 StepSize 1)> ]Privilege Level1](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-37.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 585 System Manual3.9.12.5.6 Displaying Configuration Information for Airframe Uplink Data Zone ParametersTo display configuration for the Airframe Uplink Data Zone parameters, run the following command:npu# show airframe-uldatazone bs [<(1 to 16777215 StepSize 1)>]Specify the BS ID if you want to display configuration for a particular BS. For example, to display the Airframe Uplink Data Zone parameters of BS 66503, run the following command:npu# show airframe-uldatazone bs 66053 Do not specify the BS ID if you want to view configuration information for all existing BSs. To display information for all BSs, run the following command:Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Airframe Downlink Data Zone parameters of a specific BS. Do not specify a value for this parameter if you want to display the Airframe Downlink Data Zone parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing Neighbor BS in each of the existing BSs if requested for all)BSIDLSB :<value>DLDATAZonePermutationBase :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-38.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 586 System Manualnpu# show airframe-uldatazone bs3.9.12.5.7 Displaying Configuration Information for Airframe MIMO ParametersTo display configuration for the Airframe MIMO parameters, run the following command:Command Syntaxnpu# show airframe-uldatazone bs [<(1 to 16777215 StepSize 1)> ]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Airframe Uplink Data Zone parameters of a specific BS. Do not specify a value for this parameter if you want to display the Airframe Uplink Data Zone parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing Neighbor BS in each of the existing BSs if requested for all)BSIDLSB :<value>ULDATAPermutationBase :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-39.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 587 System Manualnpu# show airframe-mimo bs [<(1 to 16777215 StepSize 1)>]Specify the BS ID if you want to display configuration for a particular BS. For example, to display the Airframe MIMO parameters of BS 66503, run the following command:npu# show airframe-mimo bs 66053 Do not specify the BS ID if you want to view configuration information for all existing BSs. To display information for all BSs, run the following command:npu# show airframe-mimo bsCommand Syntaxnpu# show airframe-mimo bs [<(1 to 16777215 StepSize 1)> ]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Airframe Dynamic Permutation parameters of a specific BS. Do not specify a value for this parameter if you want to display the Airframe Dynamic Permutation parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing Neighbor BS in each of the existing BSs if requested for all)BSIDLSB :<value>firstzoneminsize :<value>firstzonemaxsize :<value>maxmapsize :<value>](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-40.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 588 System Manual3.9.12.5.8 Displaying Configuration Information for All Airframe ParametersTo display configuration for all Airframe parameters, run the following command:npu# show airframe-all bs [<(1 to 16777215 StepSize 1)>]Specify the BS ID if you want to display configuration for a particular BS. For example, to display all Airframe parameters of BS 66503, run the following command:npu# show airframe-all bs 66053 Do not specify the BS ID if you want to view configuration information for all existing BSs. To display information for all BSs, run the following command:npu# show airframe-all bsCommand ModesGlobal command modeCommand Syntaxnpu# show airframe-all bs [<(1 to 16777215 StepSize 1)> ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display all Airframe parameters of a specific BS. Do not specify a value for this parameter if you want to display all Airframe parameters of all BSs.Optional N/A 1-16777215Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-41.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 589 System Manual3.9 .13 Managing BS Bearer Interface Pa ra m etersAfter enabling the BS configuration mode, you can execute the following tasks:Configure one or more of the Bearer Interface parameters (refer to Section 3.9.13.1).Restore the default values of some or all of the Bearer Interface parameters (refer to Section 3.9.13.2).You can display configuration information for the Bearer Interface parameters of a selected or all existing BSs (refer to Section 3.9.13.3).3.9.13.1 Configuring Bearer Interface ParametersFrom the BS configuration mode, run the following command:npu(config-bs-66053)# bearer [ip-address <ip address>] [ip-subnetmask <ip address>] [dflt-gw <ip address>] [bearer-vlan <(9 to 9 StepSize 1) | (11 to 100 StepSize 1) |(110 to 4094 StepSize 1)> ]To configure the Bearer Interface Parameters:Command Syntaxnpu(config-bs-66053)# bearer [ip-address <ip address> ] [ip-subnetmask <ip address> ] [dflt-gw <ip address> ] [bearer-vlan <(9 to 9 StepSize 1) | (11 to 100 StepSize 1) |(110 to 4094 StepSize 1)> ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-42.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 590 System Manual3.9.13.2 Restoring the Default Values of Bearer Interface ParametesTo restore the default values of the Bearer Interface bearer-vlan parameter, run the following command:npu(config-bs-66053)# no bearer [bearer-vlan][ip-address <ip address> ]The IP address of the bearer interface of the BS. Must be unique in the network. All BS bearer interfaces of the unit should be in the same subnet, together with the NPU’s bearer interface (if applicable).Mandatory when creating a new BS.N/A IP address[ip-subnetmask <ip address> ]The IP subnet mask of the bearer interface of the BSMandatory when creating a new BS.N/A Subnet mask[dflt-gw <ip address> ] The IP address of the default gateway of the bearer interface of the BS. Must be in the same subnet with the BS bearer ip interface.Mandatory when creating a new BS.N/A IP address[bearer-vlan <(9 to 9 StepSize 1) | (11 to 100 StepSize 1) |(110 to 4094 StepSize 1)> ]The VLAN ID of the bearer interface of the BS.Must be equal to the VLAN ID of the Bearer interface (see Section 3.4.2.3.5)Optional 11 9, 11-100, 110-4094.Command Modesbs configuration modeIMPORTANTWhen creating a new BS, the Bearer Interface mandatory parameters must be configured.NOTERefer to Section 3.9.13.1 for a description and default value of this parameter.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-43.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 591 System Manual3.9.13.3 Displaying Configuration Information for Bearer Interface ParametersTo display configuration information of Bearer Interface parameters, run the following command:npu# show bearer bs [<(1 to 16777215 StepSize 1)Specify the BS ID if you want to display information for a particular BS. For example, to display the Bearer Interface parameters of BS 66053, run the following command:npu# show bearer bs 66053Do not specify this parameter if you want to view information for all existing BSs. To display information for all BSs, run the following command:npu# show bearer bsCommand Syntaxnpu(config-bs-66053)# no bearer [bearer-vlan ]Privilege Level10Command Modesbs configuration modeCommand Syntaxnpu# show bearer bs [<(1 to 16777215 StepSize 1)Privilege Level1](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-44.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 592 System ManualIn addition to the configurable parameters, the ASNGW Status parameter is also displayed. This is the Bearer Interface connectivity status (up/down/unknown). If keep alive is disabled the connectivity status will be unknown. Note that the keep-alive mechanism will start only after first registration, and until then this mechanism is disabled and connectivity status is unknown.3.9 .14 Managing Aut hent ication Rela y Pa ra m e t e rsAfter enabling the BS configuration mode, you can execute the following tasks:Configure one or more of the Authentication parameters (refer to Section 3.9.14.1).Restore the default values of some or all of the Authentication non-mandatory parameters (refer to Section 3.9.14.2).Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display Bearer Interface parameters of a specific BS. Do not specify a value for this parameter if you want to display Bearer Interface parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>IPAddress :<value>IPsubnetMask :<value>DefaultGateway :<value>BearerVLANID :<value>ASNGWStatus :<value> Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-45.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 593 System ManualYou can display configuration information for the Authentication parameters of a selected or all existing BSs (refer to Section 3.9.14.3).3.9.14.1 Configuring Authentication ParametersFrom the BS configuration mode, run the following command:npu(config-bs-66053)# auth-general [dflt-auth-ip-address <ip address>] [suspendedeapprocthrshld <(0 to 10000 StepSize 1)>] [activemsthrshld <(0 to 1024 StepSize 1)>] [maxeaproundsthrshld <(0 to 100 StepSize 1)>] To configure the Authentication parameters:Command Syntaxnpu(config-bs-66053)# auth-general [dflt-auth-ip-address <ip address> ] [suspendedeapprocthrshld <(0 to 10000 StepSize 1)> ] [activemsthrshld <(0 to 1024 StepSize 1)> ] [maxeaproundsthrshld <(0 to 100 StepSize 1)> ] ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values[dflt-auth-ip-address <ip address> ]Identifier (IP address) of “default” authenticator ASN GW.Mandatory when creating a new BS.N/A IPv4 address[suspendedeapprocthrshld <(0 to 10000 StepSize 1)> ]Suspended EAP authentication process threshold. It is used to set an alarm.A value of 0 means that the alarm is disabled.In the current release the relevant alarm is not supported.Optional 10000 0 to 10000](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-46.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 594 System Manual3.9.14.2 Restoring the Default Values of Authentication ParametesTo restore the default values of some or all of the Authentication parameters, run the following command:npu(config-bs-66053)# no auth-general [suspendedeapprocthrshld] [activemsthrshld] [maxeaproundsthrshld] You can restore only some parameters to their default values by specifying only those parameters. For example, to restore only the activemsthrshld and [activemsthrshld <(0 to 1024 StepSize 1)> ]Threshold for the number of MSs in active operation state (not Idle) served by the BS. Exceeding this threshold will set the alarm “Excessive MS number”.A value of 0 means that the alarm is disabled.Optional 1024 0 to 1024[maxeaproundsthrshld <(0 to 100 StepSize 1)> ]Threshold for the number of EAP rounds in one direction in the same EAP session. When exceeding this threshold; alarm is set. May be used to protect the system from hazard EAP sessions with extreme number of messaging round trips. A value of "0" means the alarm is disabled.A value of 0 means that the alarm is disabled.In the current release the relevant alarm is not supported.Optional 100 0 to 100Command Modesbs configuration modeIMPORTANTWhen creating a new BS, the Authentication dflt-auth-ip-address mandatory parameter must be configured.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-47.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 595 System Manualmaxeaproundsthrshld parameters to the default values, run the following command:npu(config-bs-66053)# no auth-general activemsthrshld maxeaproundsthrshldThese parameters will be restored to their default values, while the other parameters will remain unchanged.To restore all Authentication parameters to their default value, run the following command:npu(config-bs-66053)# no auth-general3.9.14.3 Displaying Configuration Information for Authentication ParametersTo display configuration information of Authentication parameters, run the following command:npu# show auth-general bs [<(1 to 16777215 StepSize 1)Specify the BS ID if you want to display information for a particular BS. For example, to display the Authentication parameters of BS 66053, run the following command:npu# show auth-general bs 66053Do not specify this parameter if you want to view information for all existing BSs. To display information for all BSs, run the following command:npu# show auth-general bsNOTERefer to Section 3.9.14.1 for a description and default values of these parameters.Command Syntaxnpu(config-bs-66053)# no auth-general [suspendedeapprocthrshld ] [activemsthrshld ] [maxeaproundsthrshld ]Privilege Level10Command Modesbs configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-48.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 596 System Manual3.9 .15 Displaying St atus I nformat ion for Handover Control ParametersAfter enabling the BS configuration mode, you can display information for the Handover Control parameters of a selected or all existing BSs (refer to Section 3.9.16).To display configuration and status information of Handover Control parameters, run the following command:npu# show hoctrl bs [<(1 to 16777215 StepSize 1)Command Syntaxnpu# show auth-general bs [<(1 to 16777215 StepSize 1)Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display Authentication parameters of a specific BS. Do not specify a value for this parameter if you want to display Authentication parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-49.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 597 System ManualSpecify the BS ID if you want to display information for a particular BS. For example, to display the Handover Control parameters of BS 66053, run the following command:npu# show hoctrl bs 66053Do not specify this parameter if you want to view information for all existing BSs. To display information for all BSs, run the following command:npu# show hoctrl bsThe following status parameters related to Handover Control are displayed:Command Syntaxnpu# show hoctrl bs [<(1 to 16777215 StepSize 1)Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display Handover Control parameters of a specific BS. Do not specify a value for this parameter if you want to display Handover Control parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>SchedulingServiceSupport :<value>CINRReuse :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-50.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 598 System Manual3.9 .16 Managing Bearer Traffic QoS Marking RulesUp to 16383 Bearer Traffic QoS Marking Rules may be defined. 1Enable the BS Bearer Traffic QoS Marking Rule configuration mode for the selected Bearer Traffic QoS Marking Rule (refer to Section 3.9.16.1)2You can now execute any of the following tasks:»Configure the parameters of the Bearer Traffic QoS Marking Rule (refer to Section 3.9.16.2)»Restore the default values of Bearer Traffic QoS Marking Rule non-mandatory parameters (refer to Section 3.9.16.3)» Terminate the Bearer Traffic QoS Marking Rule configuration mode (refer to Section 3.9.16.4)In addition, you can, at any time, display configuration information for Bearer Traffic QoS Marking Rules (refer to Section 3.9.16.6) or delete an existing Bearer Traffic QoS Marking Rule (refer to Section 3.9.16.5). Parameter Description Possible ValuesSchedulingServiceSupport Scheduling Service Support. A string of two hexadecimal digits that can be presented as 8 bits where bits 5-7 are always 0. Bits 0-4 indicate whether specific services are supported, where a value of 1 means that the service is supported: UGS (0), RT-PS(1), NRT-PS(2), BE(3), ERT-PS(4).This parameter is available for populating the srvcsupport parameter in the relevant Neighbor BS General parameters tables.A string of two hexadecimal digits.CINRReuse The reuse type (calculated by the BS) to be advertised for this BS in NBR-ADV messages. reuse1reuse3To configure a Bearer Traffic QoS Marking Rule:](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-51.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 599 System Manual3.9.16.1 Enabling the Bearer Traffic QoS Marking Rule Configuration Mode\Creating a Bearer Traffic QoS Marking RuleTo configure the parameters of a Bearer Traffic QoS Marking Rule, first enable the BS Bearer Traffic QoS Marking Rule configuration mode for the specific Bearer Traffic QoS Marking Rule. Run the following command to enable the BS Bearer Traffic QoS Marking Rule configuration mode. You can also use this command to create a new Bearer Traffic QoS Marking Rule. Note that for a new Bearer Traffic QoS Marking Rule this command only defines the Bearer Traffic QoS Marking Rule number, and that the Bearer Traffic QoS Marking Rule is not fully created until completing configuration of all mandatory parameters and executing the apply command (must be executed before exiting the Bearer Traffic QoS Marking Rule configuration mode). Also when updating an existing Bearer Traffic QoS Marking Rule, the apply command must be executed prior to termination the Bearer Traffic QoS Marking Rule configuration mode.npu(config-bs-66053)# bearertrafficqos <(1 to 16383 StepSize 1)>For example, to define a new Bearer Traffic QoS Marking Rule number 1, or to enable the configuration mode for Bearer Traffic QoS Marking Rule 1, run the following command:npu(config-bs-66053)# bearertrafficqos 1If you use this command to create a new Bearer Traffic QoS Marking Rule, the configuration mode for this Bearer Traffic QoS Marking Rule is automatically enabled, after which you can execute any of the following tasks:Configure one or more of the parameters of the Bearer Traffic QoS Marking Rule (refer to Section 3.9.16.2)Restore the default values of Bearer Traffic QoS Marking Rule non-mandatory parameters (refer to Section 3.9.16.3)After executing the above tasks, you can terminate the Bearer Traffic QoS Marking Rule configuration mode (refer to Section 3.9.16.4) and return to the BS configuration mode.Command Syntaxnpu(config-bs-66053)# bearertrafficqos <(1 to 16383 StepSize 1)>Privilege Level10](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-52.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 600 System ManualFor example, to define Bearer Traffic QoS Marking Rule 1 for BS 66053, run the following command:npu(config-bs-66053)# bearertrafficqos 13.9.16.2 Configuring Bearer Traffic QoS Marking Rule ParametersTo configure the Bearer Traffic QoS Marking Rule parameters, run the following command:npu(config-bs-66053-bearertrafficqos-1)# mrkngrule [rule-status {Enable | Disable}] [rule-name <string (32)>] [srvcflow-datadeliverytype {uGS | rTVR | nRTVR | bE | eRTVR | any}] [srvcflow-trafficpriority <(0 to 7 StepSize 1) | (255 to 255 StepSize 1)>] [srvcflow-mediaflowtype <string (32)>] [enable-srvcflow-mediaflowtype {TRUE | FALSE}] [outerdscp <(0 to 63 StepSize 1)>] [bp8021p <(0 to 7 StepSize 1)>]Syntax Description Parameter Description Presence Default ValuePossible Valuesbearertrafficqos <(1 to 16383 StepSize 1)>The Bearer Traffic QoS Marking Rule numberMandatory 1 - 16383Command ModesBS configuration modeNOTEThe following examples are for BS Bearer Traffic QoS Marking Rule configuration mode for bs-66053, bearer traffic qos marking rule (bearertrafficqos)-1.IMPORTANTWhen creating a new Bearer Traffic QoS Marking Rule, the mandatory parameters must be configured.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-53.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 601 System ManualCommand Syntaxnpu(config-bs-66053-bearertrafficqos-1)# mrkngrule [rule-status {Enable | Disable} ] [rule-name <string (32)> ] [srvcflow-datadeliverytype {uGS | rTVR | nRTVR | bE | eRTVR | any} ] [srvcflow-trafficpriority <(0 to 7 StepSize 1) | (255 to 255 StepSize 1)> ] [srvcflow-mediaflowtype <string (32)> ] [enable-srvcflow-mediaflowtype {TRUE | FALSE} ] [outerdscp <(0 to 63 StepSize 1)> ] [bp8021p <(0 to 7 StepSize 1)> ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Valuesrule-status {Enable | Disable}The Bearer Traffic QoS Marking Rule statusOptional Enable EnableDisablerule-name <string (32)>The Bearer Traffic QoS Marking Rule name (descriptor).Optional null A string of up to 32 characterssrvcflow-datadeliverytype {uGS | rTVR | nRTVR | bE | eRTVR | any}Service Flow Type of data delivery services.Optional any uGSrTVRnRTVRbEeRTVRanysrvcflow-trafficpriority <(0 to 7 StepSize 1) | (255 to 255 StepSize 1)>Service Flow Traffic Priority. A value of 255 means "ANY"Optional 255 0-7 or 255](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-54.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 602 System Manual3.9.16.3 Restoring Default Values for Bearer Traffic QoS Marking Rule Configuration ParametersAfter enabling the Bearer Traffic QoS Marking Rule configuration mode you can restore the default values for non-mandatory parameters. To restore some or all of the Bearer Traffic QoS Marking Rule non-mandatory parameters to their default values, run the following command:npu(config-bs-66053-bearertrafficqos-1)# no mrkngrule [rule-status] [rule-name] [srvcflow-datadeliverytype [srvcflow-trafficpriority] [outerdscp] [bp8021p]You can restore only one or several parameters to the default values by specifying only those parameters. For example, to restore only the outerdscp to the default value, run the following command:npu(config-bs-66053-bearertrafficqos-1)# no mrkngrule outerdscpThe parameter will be restored to its default value, while the other parameters will remain unchanged.srvcflow-mediaflowtype <string (32)>One of key entries into the traffic marking rules table. Media Flow Type should be defined in ASN-GW or AAA server.Only relevant if enable-srvcflow-mediaflowtype (see below) is TRUE.Mandatory when creating a new rule (if relevant)N/A A string of up to 32 charactersenable-srvcflow-mediaflowtype {TRUE | FALSE}If TRUE, the srvcflow-mediaflowtype (see above) will be considered. when looking for a match. If FALSE it will not be considered.Mandatory when creating a new ruleTRUEFALSEouterdscp <(0 to 63 StepSize 1)>DSCP value to be used for marking of outer IP header (IP/GRE).Optional 0 0 - 63bp8021p <(0 to 7 StepSize 1)>802.1p priority to be used for marking of trafficOptional 0 0 - 7Command Modesbs bearer traffic qos marking rule configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-55.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 603 System ManualTo restore all Bearer Traffic QoS Marking Rule non-mandatory parameters to their default value, run the following command:npu(config-bs-66053-bearertrafficqos-1)# no mrkngrule3.9.16.4 Terminating the Bearer Traffic QoS Marking Rule Configuration ModeRun the following command to terminate the Bearer Traffic QoS Marking Rule configuration mode:npu(config-bs-66053-bearertrafficqos-1)# exit3.9.16.5 Deleting a Bearer Traffic QoS Marking RuleRun the following command from the BS configuration mode to delete a Bearer Traffic QoS Marking Rule:npu(config-bs 66053)# no bearertrafficqos <(1 to 16383 StepSize 1)> NOTERefer to Section 3.9.16.2 for a description and default values of these parameters.Command Syntaxnpu(config-bs-66053-bearertrafficqos-1)# no mrkngrule [rule-status ] [rule-name ] [srvcflow-datadeliverytype [srvcflow-trafficpriority ] [outerdscp ] [bp8021p ]Privilege Level10Command Modesbs bearer traffic qos marking rule configuration modeCommand Syntaxnpu(config-bs-66053-bearertrafficqos-1)# exitPrivilege Level10Command Modesbs bearer traffic qos marking rule configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-56.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 604 System Manual3.9.16.6 Displaying Configuration Information for Bearer Traffic QoS Marking RulesTo display configuration for the parameters of a specific or all Bearer Traffic QoS Marking Rules, run the following command:npu# show bearertrafficqos bs [<(1 to 16777215 StepSize 1)> number <(1 to 16383 StepSize 1)>]Specify the BS ID and Bearer Traffic QoS Marking Rule number if you want to display configuration for a particular Bearer Traffic QoS Marking Rule. For example, to display the parameters of Bearer Traffic QoS Marking Rule 1 in BS 66053, run the following command:npu# show bearertrafficqos bs 66053 number 1Do not specify these parameters if you want to view configuration information for all existing Bearer Traffic QoS Marking Rules. To display information for all Bearer Traffic QoS Marking Rules, run the following command:npu# show bearertrafficqos bsCommand Syntaxnpu(config-bs 66053)# no bearertrafficqos <(1 to 16383 StepSize 1)> Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16383 StepSize 1)>The Bearer Traffic QoS Marking Rule number Mandatory N/A 1-16383Command Modesbs configuration modeCommand Syntaxnpu# show bearertrafficqos bs [<(1 to 16777215 StepSize 1)> number <(1 to 16383 StepSize 1)> ]](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-57.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 605 System ManualPrivilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the parameters of a specific Bearer Traffic QoS Marking Rule. Do not specify a value for this parameter if you want to display the parameters of all Bearer Traffic QoS Marking Rules.Optional N/A 1-16777215number <(1 to 16383 StepSize 1)> ]The Bearer Traffic QoS Marking Rule number. To be used only if you want to display the parameters of a specific Bearer Traffic QoS Marking Rule.Optional N/A 1-16383Display Format(for each existing Service Mapping Rule if requested for all Service Mapping Rules)BSIDLSB :<value>RuleNumber :<value>RuleStatus :<value>RuleName :<value>ServiceFlowMediaFlowType :<value>ServiceFlowTrafficPriority(255meansany) :<value>ServiceFlowMediaFlowType :<value>EnableServiceFlowMediaFlowType :<value>OuterDSCP :<value>802.1pPriority :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-58.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 606 System Manual3.9 .17 Managing Control Traffic QoS Mark ing Rule sControl Traffic QoS Marking Rules are used to define the DSCP and VLAN Priority (802.1p) value to be used for marking of internal management traffic (management traffic to/from the AUs) and intra-ASN (R8/R6) management traffic.1Enable the Control Traffic QoS Marking Rules configuration mode (refer to Section 3.9.17.1)2You can now execute any of the following tasks:»Configure one or more of the Control Traffic QoS Marking Rules parameters tables (refer to Section 3.9.17.2)»Restore the default values of parameters in one or more of the Control Traffic QoS Marking Rules parameters tables (refer to Section 3.9.17.3)» Terminate the Control Traffic QoS Marking Rules configuration mode (refer to Section 3.9.17.4)In addition, you can, at any time, display configuration information for each of the parameters tables (refer to Section 3.9.17.5).3.9.17.1 Enabling the Control Traffic QoS Marking Rules Configuration ModeTo configure the Control Traffic QoS Marking Rules parameters, first enable the Control Traffic QoS Marking Rules configuration mode. Run the following command to enable the Control Traffic QoS Marking Rules configuration mode. npu(config-bs-66053)# ctrltrafficqosThe configuration mode for the Control Traffic QoS Marking Rules is enabled, after which you can execute any of the following tasks:Configure one or more of the Control Traffic QoS Marking Rules parameters tables (refer to Section 3.9.17.2)Restore the default values of parameters in one or more of the parameters tables (refer to Section 3.9.17.3)To configure the Control Traffic QoS Marking Rules:](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-59.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 607 System ManualAfter executing the above tasks, you can terminate the Control Traffic QoS Marking Rules configuration mode (refer to Section 3.9.17.4) and return to the BS configuration mode.3.9.17.2 Configuring Control Traffic QoS Marking Rules ParametersAfter enabling the Control Traffic QoS Marking Rules configuration mode you can configure the following parameters tables:Internal Management (refer to Section 3.9.17.2.1)Intra ASN (refer to Section 3.9.17.2.2)3.9.17.2.1 Configuring Internal Management Traffic QoS Marking Rules ParametersTo configure the Internal Management Traffic QoS Marking Rules, run the following command:npu(config-bs-66053-ctrltrafficqos)# intmngmnt [dscp <(0 to 63 StepSize 1)>] [inter8021p <(0 to 7 StepSize 1)>]Command Syntaxnpu(config-bs-66053)# ctrltrafficqosPrivilege Level10Command Modesbs configuration modeCommand Syntaxnpu(config-bs-66053-ctrltrafficqos)# intmngmnt [dscp <(0 to 63 StepSize 1)> ] [inter8021p <(0 to 7 StepSize 1)> ]Privilege Level10](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-60.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 608 System Manual3.9.17.2.2 Configuring the Intra ASN Traffic QoS Marking RulesTo configure the Intra ASN Traffic QoS Marking Rules parameters, run the following command:npu(config-bs-66053-ctrltrafficqos)# intraasn [dscp <(0 to 63 StepSize 1)>] [intra8021p <(0 to 7 StepSize 1)>]Syntax Description Parameter Description Presence Default ValuePossible Valuesdscp <(0 to 63 StepSize 1)>DSCP priority value to be used for marking of internal management trafficOptional 0 0 - 63inter8021p <(0 to 7 StepSize 1)>802.1p priority value to be used for marking of internal management trafficOptional 0 0 - 7Command Modesbs control traffic qos marking rules (ctrltrafficqos) configuration mode Command Syntaxnpu(config-bs-66053-ctrltrafficqos)# intraasn [dscp <(0 to 63 StepSize 1)> ] [intra8021p <(0 to 7 StepSize 1)> ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Valuesdscp <(0 to 63 StepSize 1)>DSCP priority value to be used for marking of intra-ASN (R8/R6) trafficOptional 0 0 - 63intra8021p <(0 to 7 StepSize 1)>802.1p priority value to be used for marking of intra-ASN (R8/R6) trafficOptional 0 0 - 7](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-61.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 609 System Manual3.9.17.3 Restoring Default Values for Control Traffic QoS Marking Rules Configuration ParametersAfter enabling the Control Traffic QoS Marking Rules configuration mode you can restore the default values for parameters in the following parameters tables:Internal Management (refer to Section 3.9.17.3.1)Intra ASN (refer to Section 3.9.17.3.2)3.9.17.3.1 Restoring the Default Values of Internal Management Traffic QoS Marking Rules ParametersTo restore one or all of the Internal Management Traffic QoS Marking Rules parameters to their default values, run the following command:npu(config-bs-66053-ctrltrafficqos)# no intmngmnt [dscp] [inter8021p]You can restore only one parameter to its default values by specifying only that parameter. For example, to restore only dscp to the default value, run the following command:npu(config-bs-66053-ctrltrafficqos)# no intmngmnt dscpThe parameter will be restored to its default value, while the other parameter will remain unchanged.To restore all Internal Management Traffic QoS Marking Rules parameters to their default value, run the following command:npu(config-bs-66053-ctrltrafficqos)# no intmngmntCommand Modesbs control traffic qos marking rules (ctrltrafficqos) configuration mode NOTERefer to Section 3.9.17.2.1 for a description and default values of these parameters.Command Syntaxnpu(config-bs-66053-ctrltrafficqos)# no intmngmnt [dscp ] [inter8021p ]Privilege Level10](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-62.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 610 System Manual3.9.17.3.2 Restoring the Default Values of Intra ASN Traffic QoS Marking Rules ParametersTo restore one or all of the Intra ASN Traffic QoS Marking Rules parameters to their default values, run the following command:npu(config-bs-66053-ctrltrafficqos)# no intraasn [dscp] [intra8021p]You can restore only one parameter to its default values by specifying only that parameter. For example, to restore only dscp to the default value, run the following command:npu(config-bs-66053-ctrltrafficqos)# no intraasn dscpThe parameter will be restored to its default value, while the other parameter will remain unchanged.To restore all Intra ASN Traffic QoS Marking Rules parameters to their default value, run the following command:npu(config-bs-66053-ctrltrafficqos)# no intraasn3.9.17.4 Terminating the Control Traffic QoS Marking Rules Configuration ModeRun the following command to terminate the Control Traffic QoS Marking Rules configuration mode:npu(config-bs-66053-ctrltrafficqos)# exitCommand Modesbs control traffic qos marking rules (ctrltrafficqos) configuration mode NOTERefer to Section 3.9.17.2.2 for a description and default values of these parameters.Command Syntaxnpu(config-bs-66053-ctrltrafficqos)# no intraasn [dscp ] [intra8021p ]Privilege Level10Command Modesbs control traffic qos marking rules (ctrltrafficqos) configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-63.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 611 System Manual3.9.17.5 Displaying Configuration Information for Control Traffic QoS Marking Rules ParametersYou can display the current configuration information for the following parameters tables:Internal Management (refer to Section 3.9.17.5.1)Intra ASN (refer to Section 3.9.17.5.2)All (refer to Section 3.9.17.5.3)3.9.17.5.1 Displaying Configuration Information for Internal Management Traffic QoS Marking Rules ParametersTo display configuration for the Internal Management Traffic QoS Marking Rules parameters, run the following command:npu# show ctrltrafficqos-intmngmnt bs [<(1 to 16777215 StepSize 1)Specify the BS ID if you want to display configuration for a particular BS. For example, to display the Internal Management Traffic QoS Marking Rules parameters of BS 66053, run the following command:npu# show ctrltrafficqos-intmngmnt bs 66053Do not specify this parameter if you want to view configuration information for all existing BSs. To display information for all BSs, run the following command:npu# show ctrltrafficqos-intmngmnt bsCommand Syntaxnpu(config-bs-66053-ctrltrafficqos)# exitPrivilege Level10Command Modesbs control traffic qos marking rules (ctrltrafficqos) configuration modeCommand Syntaxnpu# show ctrltrafficqos-intmngmnt bs [<(1 to 16777215 StepSize 1)](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-64.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 612 System Manual3.9.17.5.2 Displaying Configuration Information for Intra ASN Traffic QoS Marking Rules ParametersTo display configuration for the Intra ASN Traffic QoS Marking Rules parameters, run the following command:npu# show ctrltrafficqos-intraasn bs [<(1 to 16777215 StepSize 1)Specify the BS ID if you want to display configuration for a particular BS. For example, to display the Intra ASN Traffic QoS Marking Rules parameters of BS 66053, run the following command:npu# show ctrltrafficqos-intraasn bs 66053Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Internal Management Traffic QoS Marking Rules parameters of a specific BS. Do not specify a value for this parameter if you want to display the Internal Management Traffic QoS Marking Rules parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>InternalManagementDSCP :<value>InternalManagement802.1pPriority :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-65.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 613 System ManualDo not specify this parameter if you want to view configuration information for all existing BSs. To display information for all BSs, run the following command:npu# show ctrltrafficqos-intraasn bs3.9.17.5.3 Displaying Configuration Information for All Control Traffic QoS Marking Rules ParametersTo display configuration for all Control Traffic QoS Marking Rules parameters, run the following command:Command Syntaxnpu# show ctrltrafficqos-intraasn bs [<(1 to 16777215 StepSize 1)Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Intra ASN Traffic QoS Marking Rules parameters of a specific BS. Do not specify a value for this parameter if you want to display the Intra ASN Traffic QoS Marking Rules parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>IntraASNDSCP :<value>IntraASN802.1pPriority :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-66.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 614 System Manualnpu# show ctrltrafficqos-all bs [<(1 to 16777215 StepSize 1)Specify the BS ID if you want to display configuration for a particular BS. For example, to display all Control Traffic QoS Marking Rules parameters of BS 66053, run the following command:npu# show ctrltrafficqos-all bs 66053Do not specify this parameter if you want to view configuration information for all existing BSs. To display information for all BSs, run the following command:npu# show ctrltrafficqos-all bsCommand Syntaxnpu# show ctrltrafficqos-all bs [<(1 to 16777215 StepSize 1) Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display all Control Traffic QoS Marking Rules parameters of a specific BS. Do not specify a value for this parameter if you want to display all Control Traffic QoS Marking Rules parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>IntraASNDSCP :<value>IntraASN802.1pPriority :<value>InternalManagementDSCP :<value>InternalManagement802.1pPriority :<value>](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-67.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 615 System Manual3.9 .18 Managing ID-IP Mapping Pa ra m e t e rsAfter enabling the BS configuration mode, you can execute the following tasks:Configure one or more ID-IP Mapping entry (refer to Section 3.9.18.1).Delete one or more ID-IP Mapping entries (refer to Section 3.9.18.2).You can display configuration information for the ID-IP Mapping of a selected or all existing BSs (refer to Section 3.9.18.3).3.9.18.1 Configuring ID-IP Mapping EntriesFrom the BS configuration mode, run the following command:npu(config-bs-66053)# idip <(1 to 16777215 StepSize 1)> [nw-node-ip <ip address>]Command ModesGlobal command modeTo configure ID-IP Mapping entries:Command Syntaxnpu(config-bs-66053)# idip <(1 to 16777215 StepSize 1)> [nw-node-ip <ip address> ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The Next Hop (Network Node) BS IDMandatory N/A 1 - 16777215nw-node-ip <ip address> The Next Hop (Network Node) BS IP AddressMandatory N/A IP address](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-68.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 616 System Manual3.9.18.2 Deleting an ID-IP Mapping EntryRun the following command from the BS configuration mode to delete an ID-IP Mapping entry:npu(config-bs 66053)# no idip <(1 to 16777215 StepSize 1)> 3.9.18.3 Displaying Configuration Information for ID-IP Mapping EntriesTo display configuration information of ID-IP Mapping entries, run the following command:npu# show idip bs [<(1 to 16777215 StepSize 1)> nw-node-id <(1 to 16777215 StepSize 1)>]Specify the BS ID and Next Hop (Network Node) BS ID (nw-node-id) if you want to display information for a particular ID-IP Mapping entry. For example, to display the ID-IP Mapping of BS 66053 and Network Node 66055, run the following command:Command Modesbs configuration modeIMPORTANTWhen creating a new BS, at least one ID-IP Mapping entry must be configured.Command Syntaxnpu(config-bs 66053)# no idip <(1 to 16777215 StepSize 1)> Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The Next Hop (Network Node) BS IDMandatory N/A 1 - 16777215Command Modesbs configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-69.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 617 System Manualnpu# show idip bs 66053 nw-node-id 66055Do not specify these parameters if you want to view information of ID-IP Mapping entries in all existing BSs. To display information for all BSs, run the following command:npu# show idip bsCommand Syntaxnpu# show idip bs [<(1 to 16777215 StepSize 1)> nw-node-id <(1 to 16777215 StepSize 1)> ]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display specific ID-IP Mapping entry in a specific BS. Do not specify a value for this parameter if you want to display all ID-IP Mapping entries of all BSs.Optional N/A 1-16777215nw-node-id <(1 to 16777215 StepSize 1)>The Next Hop (Network Node) BS ID.Specify a value for this parameter if you want to display a specific ID-IP Mapping entry in a specific BS. Do not specify a value for this parameter if you want to display all ID-IP Mapping entries of all BSs.Optional N/A 1-16777215](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-70.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 618 System ManualDisplay Format(for each entry if requested for all)BSIDLSB :<value>NetworkNodeID :<value>NetworkNodeIPAddress :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-71.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 619 System Manual3.9 .19 Managing Ranging Para m e t e rs1Enable the Ranging configuration mode (refer to Section 3.9.19.1)2You can now execute any of the following tasks:»Configure the Ranging General parameters (refer to Section 3.9.19.2)»Restore the default values of one or more of the Ranging General parameters (refer to Section 3.9.19.3)» Terminate the Ranging configuration mode (refer to Section 3.9.19.4)In addition, you can, at any time, display configuration information for the Ranging General parameters (refer to Section 3.9.19.5).3.9.19.1 Enabling the Ranging Configuration ModeTo configure the Ranging parameters, first enable the Ranging configuration mode. Run the following command to enable the Ranging configuration mode. npu(config-bs-66053)# rangingThe Ranging configuration mode is enabled, after which you can execute any of the following tasks:Configure one or more of the Ranging General parameters (refer to Section 3.9.19.2)Restore the default values of one or more of the Ranging General parameters (refer to Section 3.9.19.3)After executing the above tasks, you can terminate the Ranging configuration mode (refer to Section 3.9.19.4) and return to the BS configuration mode.To configure the Ranging parameters:Command Syntaxnpu(config-bs-66053)# rangingPrivilege Level10](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-72.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 620 System Manual3.9.19.2 Configuring Ranging ParametersTo configure the Ranging General parameters, run the following command:npu(config-bs-66053-ranging)# general [start-of-rng-codes <(0 to 255 StepSize 1)>] [max-cellradius {one | two | four | eight | fifteen | twentyThree | thirty}]Command Modesbs configuration modeCommand Syntaxnpu(config-bs-66053-ranging)# general [start-of-rng-codes <(0 to 255 StepSize 1)> ] [max-cellradius {one | two | four | eight | fifteen | twentyThree | thirty} ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Valuesstart-of-rng-codes <(0 to 255 StepSize 1)>Start of Ranging Codes: The starting number S of the group of codes used for this uplink.Actual valid values are 0, 64, 128, 192. If a different value is configured-the highest valid value that is lower than the configured value will be set (for example, for a configured value of 140 the actual value will be 128).Optional 0 0 - 255](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-73.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 621 System Manual3.9.19.3 Restoring Default Values for Ranging Configuration ParametersTo restore one or all of the Ranging General parameters to their default values, run the following command:npu(config-bs-66053-ranging)# no general [start-of-rng-codes] [max-cellradius]You can restore only one parameter to its default values by specifying only this parameter. For example, to restore only max-cellradius to the default value, run the following command:npu(config-bs-66053-ranging)# no general max-cellradiusThe parameter will be restored to its default value, while the other parameter will remain unchanged.To restore all Ranging General parameters to their default value, run the following command:npu(config-bs-66053-ranging)# no generalmax-cellradius {one | two | four | eight | fifteen | twentyThree | thirty}The Maximum Cell Radius (in km)Optional two onetwofoureightfifteentwentyThreethirtyCommand Modesbs ranging configuration mode NOTERefer to Section 3.9.19.2 for a description and default values of these parameters.Command Syntaxnpu(config-bs-66053-ranging)# no general [start-of-rng-codes ] [max-cellradius ]](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-74.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 622 System Manual3.9.19.4 Terminating the Ranging Configuration ModeRun the following command to terminate the Ranging configuration mode:npu(config-bs-66053-ranging)# exit3.9.19.5 Displaying Configuration Information for Ranging ParametersTo display configuration for the Ranging General parameters, run the following command:npu# show ranging-general bs [<(1 to 16777215 StepSize 1)Specify the BS ID if you want to display configuration for a particular BS. For example, to display the Ranging General parameters of BS 66053, run the following command:npu# show ranging-general bs 66053Do not specify this parameter if you want to view configuration information for all existing BSs. To display information for all BSs, run the following command:Privilege Level10Command Modesbs ranging configuration mode IMPORTANTIf you did not configure any of the BS General parameters, do not forget to execute the apply command before terminating the Ranging configuration mode: npu(config-bs-66053-ranging)# applyCommand Syntaxnpu(config-bs-66053-ranging)# exitPrivilege Level10Command Modesbs ranging configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-75.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 623 System Manualnpu# show ranging-general bs3.9 .20 Managing Alarm T hreshold ParametersAfter enabling the BS configuration mode, you can execute the following tasks:Configure one or more of the Alarm Threshold parameters (refer to Section 3.9.20.1).Restore the default values of some or all of the Alarm Threshold parameters (refer to Section 3.9.20.2).Command Syntaxnpu# show ranging-general bs [<(1 to 16777215 StepSize 1)Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Ranging General parameters of a specific BS. Do not specify a value for this parameter if you want to display the Ranging General parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>StartofRangingCodes :<value>MaximumCellRadius(km) :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-76.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 624 System ManualYou can display configuration and status information for the Alarm Threshold parameters of a selected or all existing BSs (refer to Section 3.9.20.3).3.9.20.1 Configuring Alarm Threshold ParametersFrom the BS configuration mode, run the following command:npu(config-bs-66053)# alrm-thrshld [ul-mednoise <(-135 to -100 StepSize 1)>] [ul-99prcntnoise <(-135 to -100 StepSize 1)>] [Be-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ] [rt-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ] [nrt-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ] [ugs-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ] [ert-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ]To configure the Alarm Threshold parameters:Command Syntaxnpu(config-bs-66053)# alrm-thrshld [ul-mednoise <(-135 to -100 StepSize 1)> ] [ul-99prcntnoise <(-135 to -100 StepSize 1)> ] [Be-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ] [rt-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ] [nrt-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ] [ugs-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ] [ert-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-77.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 625 System Manualul-mednoise <(-135 to -100 StepSize 1)>The uplink median noise level represents the median value of the noise floor histogram. If the uplink median noise level exceeds this value, an excessive uplink median noise alarm will be generated.The value is in dBm/tone.The default value is set to 3 dB above the default value of the target noise and interference level for the PUSC zone (target-ni parameter, see Section 3.9.4.2.1) Optional -124 -135 to -100ul-99prcntnoise <(-135 to -100 StepSize 1)>The uplink 99% noise level represents the 99% value of the noise floor histogram. If the uplink 99% noise level exceeds this value, an excessive uplink 99% percentile noise alarm will be generated.Optional -100 -135 to -100[Be-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ]Threshold for Excessive DL Dropped Packets Ratio for Best Effort (in promils)Optional 1000 1 - 1000[rt-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ]Threshold for Excessive DL Dropped Packets Ratio for Real Time (in promils)Optional 1000 1 - 1000[nrt-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ]Threshold for Excessive DL Dropped Packets Ratio for Non Real Time (in promils)Optional 1000 1 - 1000[ugs-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ]Threshold for Excessive DL Dropped Packets Ratio for UGS (in promils)Optional 1000 1 - 1000](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-78.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 626 System Manual3.9.20.2 Restoring the Default Values of Alarm Threshold ParametesTo restore the default values of some or all of the Alarm Threshold parameters, run the following command:npu(config-bs-66053)# no alrm-thrshld [ul-mednoise] [ul-99prcntnoise] [Be-exc-dl-drop-thr ] [rt-exc-dl-drop-thr ] [nrt-exc-dl-drop-thr ] [ugs-exc-dl-drop-thr ] [ert-exc-dl-drop-thr ]You can restore only some parameters to the default values by specifying only those parameter. For example, to restore only the ul-mednoise parameter to the default value, run the following command:npu(config-bs-66053)# no alrm-thrshld ul-mednoiseThis parameter will be restored to its default value, while the other parameters will remain unchanged.To restore all Alarm Threshold parameters to their default value, run the following command:npu(config-bs-66053)# no alrm-thrshld[ert-exc-dl-drop-thr <(1 to 1000 StepSize 1)> ]Threshold for Excessive DL Dropped Packets Ratio for ERT (in promils)Optional 1000 1 - 1000Command Modesbs configuration modeNOTERefer to Section 3.9.20.1 for a description and default values of these parameters.Command Syntaxnpu(config-bs-66053)# no alrm-thrshld [ul-mednoise ] [ul-99prcntnoise ] [Be-exc-dl-drop-thr ] [rt-exc-dl-drop-thr ] [nrt-exc-dl-drop-thr ] [ugs-exc-dl-drop-thr ] [ert-exc-dl-drop-thr ]Privilege Level10Command Modesbs configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-79.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 627 System Manual3.9.20.3 Displaying Configuration Information for Alarm Threshold ParametersTo display configuration information of Alarm Threshold parameters, run the following command:npu# show alrm-thrshld bs [<(1 to 16777215 StepSize 1)Specify the BS ID if you want to display information for a particular BS. For example, to display the Alarm Threshold parameters of BS 66053, run the following command:npu# show alrm-thrshld bs 66053Do not specify this parameter if you want to view information for all existing BSs. To display information for all BSs, run the following command:npu# show alrm-thrshld bsCommand Syntaxnpu# show alrm-thrshld bs [<(1 to 16777215 StepSize 1)Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display Alarm Threshold parameters of a specific BS. Do not specify a value for this parameter if you want to display Alarm Threshold parameters of all BSs.Optional N/A 1-16777215](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-80.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 628 System Manual3.9 .21 Managing BS Rese r ve d Pa rameters3.9 .22 Managing the BS Ke e p-Alive Functionalit yOnce an MS enters the network, its context is stored in ASN entities (BS, ASN-GW). Dynamically, MS context could be transferred/updated (during HO and re-authentication) to other entities or duplicated to other entities (separation between anchor functions such as Authenticator, Data Path and Relay Data Path).Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>UplinkMedNoiseUplink99%Noise(dBm) :<value>ThresholdforExcessiveDLDroppedPacketsRatioBestEffort:<value>ThresholdforExcessiveDLDroppedPacketsRatioRealTime:<value>ThresholdforExcessiveDLDroppedPacketsRatioNonRealTime:<value>ThresholdforExcessiveDLDroppedPacketsRatioUgs :<value>ThresholdforExcessiveDLDroppedPacketsRatioErt :<value>Command ModesGlobal command modeNOTEThe BS reserved parameters table enables configuring up to 21 parameters that are reserved for possible future use. In the current release none of the reserved parameters is being used. Therefore, the following commands are not applicable:Configure reserved parameters: npu (config-bs-<N>)# bs-reserved [reserved-1 <string (32)> ] [reserved-2 <string (32)> ] [reserved-3 <string (32)> ] [reserved-4 <string (32)> ] [reserved-5 <string (32)> ] [reserved-6 <string (32)> ] [reserved-7 <string (32)> ] [reserved-8 <string (32)> ] [reserved-9 <string (32)> ] [reserved-10 <string (32)> ] [reserved-11 <string (32)> ] [reserved-12 <string (32)> ] [reserved-13 <string (32)> ] [reserved-14 <string (32)> ] [reserved-15 <string (32)> ] [reserved-16 <string (32)> ] [reserved-17 <string (32)> ] [reserved-18 <string (32)> ] [reserved-19 <string (32)> ] [reserved-20 <string (32)> ] [reserved-21 <string (32)> ].Restore default values of reserved parameters: npu(config-bs-<N>)# no bs-reserved [reserved-1 ] [reserved-2 ] [reserved-3 ] [reserved-4 ] [reserved-5 ] [reserved-6 ] [reserved-7 ] [reserved-8 ] [reserved-9 ] [reserved-10 ] [reserved-11 ] [reserved-12 ] [reserved-13 ] [reserved-14 ] [reserved-15 ] [reserved-16 ] [reserved-17 ] [reserved-18 ] [reserved-19 ] [reserved-20 ] [reserved-21 ].Display configured values of reserved parameters: npu# show bs-reserved bs [<(1 to 16777215 StepSize 1).](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-81.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 629 System ManualIn certain cases, such as entity reset, other entities are not aware of service termination of an MS in that entity, and keep maintaining the MS context. This may result in service failure, excessive consumption of memory resources and accounting mistakes. The keep-alive mechanism should be used to clear MS context from all network entities when it is de-attached from the BS, and de-register MS from the network when its context becomes unavailable in one of its serving function locations.When the keep-alive mechanism is enabled the BS periodically polls other ASN-GW entities-of-interest and waits for their responses. In case of no keep-alive response, the BS shall make further actions, such as graceful de-registration of applicable MS(s) and clearing the applicable MS(s) context.The BS builds a list of ASN-GW-of-Interest, which it must poll. The list is dynamically updated; when a new MS is attached to the BS, or MS performs CSN mobility (data-path relocation) and in its context there is an ASN-GW identifier unknown to this BS, it shall add it to the ASN-GW-of-interest list. When the last MS(s) with specific ASN-GW identifier exits the network, the BS shall remove the ASN-GW from the list. The BS shall include in the ASN-GW-of-interest list also Relay Data-path ASN-GW(s) (UL next hop IP address). This is applicable when hierarchical data-path establishment takes place during inter-ASN HO.The BS periodically polls the ASN-GW(s) for keep-alive. The polling mechanism is independent and unrelated for every ASN-GW-of-interest the BS polls. The keep-alive mechanism uses configurable retry timer and retries counter. Upon expiration of the retry timer, the BS resends the BS Keep-Alive request message. Upon expiration of the retries counter, the BS assumes failure of the polled ASN-GW and clears the contexts of all MS(s) served by that ASN-GW. In addition, the BS verifies that for each polled entity that the “Last-Reset-Time” UTC value of poll N+1 is equal to the value of poll N. If the “Last-Reset-Time” UTC value of poll N+1 is higher than the value of poll N, this mean that the ASN-GW went through reset state during the interval between two consecutive polls. In this case, the BS shall de-register all MS(s) served by that specific ASN-GW and clear their contexts.When keep-alive fails, the BS generates an alarm and log the event.Regardless of the enable/disable status of the keep-alive mechanism in the BS, it replies to BS_Keep_Alive_Req received from ASN-GWs with BS_Keep_Alive_Rsp. that includes also its “Last-Reset-Time”. It responds only if all its functions operate properly. In case one of the functions fails, the BS shall not respond to the keep-alive poll.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-82.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 630 System Manual3.9.22.1 Configuring BS Keep-Alive ParametersTo configure one or several keep-alive parameters, run the following command:npu(config-bs-66053)# keep-alive [asn-ka {enable | disable} ] [period <(10 to 1000 StepSize 1)> ] [rtx-cnt <(0 to 10 StepSize 1)> ] [rtx-time <(5000 to 10000 StepSize 1)> ]IMPORTANTAn error may occur if you provide an invalid value for any of these parameters. Refer to the syntax description for more information about the appropriate values and format for configuring these parameters.An error may occur if you provide configuration values that do not satisfy following condition: 'period*1000 >= rtx-time * (rtx-cnt + 1)'"At least one parameter must be specified (the value is optional): The command npu(config-bs-66053)# keep-alive will return an Incomplete Command error.Command Syntaxnpu(config-bs-66053)# keep-alive [asn-ka {enable | disable} ] [period <(10 to 1000 StepSize 1)> ] [rtx-cnt <(0 to 10 StepSize 1)> ] [rtx-time <(5000 to 10000 StepSize 1)> ] Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values[asn-ka {enable | disable} ]Enable/Disable the BS keep-alive mechanism.Optional disable enabledisable[period <(10 to 1000 StepSize 1)> ]The period in seconds between polling sessions.period x 1000 (value in milliseconds) cannot be lower than (rtx-cnt ) x rtx-time+1).Optional 60 10-1000[rtx-cnt <(0 to 10 StepSize 1)> ]Maximum number of retries if rtx-time has expired without getting a response.Optional 5 0-10](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-83.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 631 System Manual3.9.22.2 Displaying Configuration Information for BS Keep-Alive Parameters To display the BS keep-alive parameters, run the following command:npu# show keep-alive bs [<(1 to 16777215 StepSize 1)[rtx-time <(5000 to 10000 StepSize 1)> ]Time in milliseconds to wait for a response before initiating another polling attempt or reaching a decision that the polled entity has failed (if the maximum number of retries set by rtx-cnt has been reached).Optional 5000 5000-10000Command Modesbs configuration modeCommand Syntaxnpu# show keep-alive bs (<(1 to 16777215 StepSize 1)Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display the Keep-Alive parameters of a specific BS. Do not specify a value for this parameter if you want to display the Keep-Alive parameters of all BSs.Optional N/A 1-16777215](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-84.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 632 System Manual3.9 .23 Managing the BS Idle Mode ParametersThe single sector Idle Mode capability provides the benefits of MS power savings and manageable total sector active and non active users, together with reduced overhead on the backhaul network.Idle Mode (IM) mechanism allows an MS to become unavailable on the air interface, and thus freeing operational resources and preserving MS power. During IM operation, an MS switch off its transmission and reception capabilities, and becomes available for DL broadcast control messaging, i.e., MS Paging, in a periodically manner. Using paging broadcast, BS can indicate (if necessary) the MS to exit from IM and return into normal operation mode. The paging control message is sent over the DL of a set of BSs simultaneously. This set is called Paging group (PG). In the current release, each Paging Group includes a single BS.During IM, MS performs location updates when moving from one PG to another. While in the same PG, MS does not need to transmit in the UL and can be paged in the DL if there is traffic targeted at it.After enabling the BS configuration mode, you can configure the Idle Mode parameter (refer to Section 3.9.23.1).You can display configuration information for the Idle Mode parameter of a selected or all existing BSs (refer to Section 3.9.23.2).3.9.23.1 Configuring the BS Idle Mode ParameterFrom the BS configuration mode, run the following command:npu(config-bs-66053)# idle-mode [paging-group-id <(0 to 65535 StepSize 1)> ] Display FormatBSIDLSB Keep Alive ConfigurationASN-KA : <enable/disable>Period (sec) : <value>Retransmissions Count : <value>Retransmission Time : <value>Command ModesGlobal command modeTo configure the BS Idle Mode Parameter:](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-85.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 633 System Manual3.9.23.2 Displaying Configuration Information for the BS Idle Mode ParameterTo display configuration information of the BS Idle Mode parameter of a specific or all BSs, run the following command:npu# show idle-mode bs [<(1 to 16777215 StepSize 1)>]Specify the BS ID (1-16777215) of an existing BS if you want to display configuration information for a particular BS. Do not specify values for this parameter if you want to view configuration information for all existing BSs.Command Syntaxnpu(config-bs-66053)# idle-mode [paging-group-id <(0 to 65535 StepSize 1)>] Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values[paging-group-id <(0 to 65535 StepSize 1)> ]The Paging Group ID of the BS.0 means that Idle Mode is disabled.If other than 0 (disable), should be unique in the network (different paging-group for each BS).Mandatory 0 0 to 65535Command Modesbs configuration mode Command Syntaxnpu# show idle-mode bs [<(1 to 16777215 StepSize 1)> ]Privilege Level1](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-86.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 634 System Manual3.9 .24 Managing Schedule r Pa ra m e t e rsScheduling uncommitted traffic (above the maximum reserved rate) can be done using one of the following options:Equal Time (ET) scheduling mode, in which air resources are being scheduled in a fair manner proportional to the users' excess traffic (maximum sustained rate - maximum reserved rate) SLAs.Equal Rate (ER) scheduling mode, in which air resources are allocated to users aiming at ensuring data rate fairness between users proportional to their excess traffic SLAs.Assuming a sector with diversity (different channels conditions) of active users, ET scheme enables higher aggregate sector throughput at the expense of data-rate Syntax Description Parameter Description Presence Default ValuePossible Values[<(1 to 16777215 StepSize 1)> ]The BS ID Specify a value for this parameter if you want to display the Idle Mode Paging Group ID Parameter of a specific BS. Do not specify a value for this parameter if you want to display the Idle Mode Paging Group ID Parameter of all BSs.Optional N/A 1-16777215Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>PagingGrpId :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-87.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 635 System Manualfairness among users, while ER scheduling scheme ensures maximum data-rate fairness among users at the expense of lower aggregate sector throughput.Using ER scheduling scheme exposes the system to excessive allocation of air resources to highly active users having relatively poorer channel conditions. To ensure data-rate fairness, more resources will to be allocated to these users compared to users with relatively good channel conditions. The effect of a small number of such users within the sector will be reflected by reduced aggregate sector throughput as well as degradation of achievable rates for all users. To protect against “abusing” users, an instantaneous rate threshold can be defined within the scheduling scheme in which the amount of air resources for users with continuous instantaneous rate below the threshold is being limited. The more the abusing users' instantaneous rate is below the threshold, the more resource allocations limitation is applied. Three levels of dynamic protection are available:No protection. Low protection level - protection against users with very poor channel conditions. Should be used where the abusing users instantaneous rates are far below the average instantaneous rate within the sector.Medium protection - protection against users with relatively poor or very poor channel conditions. Should be used where the abusing users instantaneous rates are below or far below the average instantaneous rate within sector.A dynamic protection mechanism is implemented, in which the mechanism of limiting resource allocations is automatically and dynamically activated when needed.After enabling the BS configuration mode, you can execute the following tasks:Configure one or more of the Scheduler parameters (refer to Section 3.9.24.1).Restore the default values of some or all of the Scheduler parameters (refer to Section 3.9.24.2).You can display configuration and status information for the Scheduler parameters of a selected or all existing BSs (refer to Section 3.9.24.3).](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-88.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 636 System Manual3.9.24.1 Configuring Scheduler ParametersFrom the BS configuration mode, run the following command:npu(config-bs-66053)# scheduler [scheduler-mode {equalRate | equalTime} ] [dl-abuse-protection-level {none | low | medium} ] [ul-abuse-protection-level {none | low | medium} ]To apply the changes, run the following command: npu(config-bs-66053)# scheduler-applyTo configure the Scheduler parameters:Command Syntaxnpu(config-bs-66053)# scheduler [scheduler-mode {equalRate | equalTime} ] [dl-abuse-protection-level {none | low | medium} ] [ul-abuse-protection-level {none | low | medium} ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Valuesscheduler-mode {equalRate | equalTime} ]The scheduling scheme for uncommitted data.Optional equalRate equalRateequalTimedl-abuse-protection-level {none | low | medium}The protection level for the downlink for equalRate scheduling mode.Optional none nonelowmediumul-abuse-protection-level {none | low | medium}The protection level for the uplink for equalRate scheduling mode.Optional none nonelowmediumCommand Modesbs configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-89.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 637 System Manual3.9.24.2 Restoring the Default Values of Scheduler ParametersTo restore the default values of some or all of the Scheduler parameters, run the following command:npu(config-bs-66053)# no scheduler [scheduler-mode ] [dl-abuse-protection-level ] [ul-abuse-protection-level ]You can restore only some parameters to the default values by specifying only those parameter. For example, to restore only the ul-abuse-protection-level parameter to the default value, run the following command:npu(config-bs-66053)# no scheduler ul-abuse-protection-levelThis parameter will be restored to its default value, while the other parameters will remain unchanged.To restore all parameters to their default value, run the following command:npu(config-bs-66053)# no schedulerTo apply the changes, run the following command: npu(config-bs-66053)# scheduler-apply3.9.24.3 Displaying Configuration Information for Scheduler ParametersTo display configuration information of Scheduler parameters, run the following command:npu# show scheduler bs [<(1 to 16777215 StepSize 1)NOTERefer to Section 3.9.24.1 for a description and default values of these parameters.Command Syntaxnpu(config-bs-66053)# no scheduler [scheduler-mode ] [dl-abuse-protection-level ] [ul-abuse-protection-level ]Privilege Level10Command Modesbs configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-90.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 638 System ManualSpecify the BS ID if you want to display information for a particular BS. For example, to display the Scheduler parameters of BS 66053, run the following command:npu# show scheduler bs 66053Do not specify this parameter if you want to view information for all existing BSs. To display information for all BSs, run the following command:npu# show scheduler bsCommand Syntaxnpu# show scheduler bs [<(1 to 16777215 StepSize 1)Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display parameters of a specific BS. Do not specify a value for this parameter if you want to display parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>scheduler-mode : <equalRate| equalTime>dl-abuse-protection-level : <none | low | medium>ul-abuse-protection-level : <none | low | medium>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-91.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 639 System Manual3.9 .25 Managing the BS ASN-GW Load Balancing Pa ra m e t e rsThe Load Balancing feature provides a WiMAX operator with the capability to build resilient ASN infrastructure using ASN-GW redundancy. Every BS is provisioned with a list of redundant ASN-GWs (pool). The BS applies round-robin mechanism in order to pick an Authenticator for each MS that performs initial network entry. This should eventually distribute the load between Anchor ASNGWs. Geographical site backup can be achieved by using different priority of ASN-GW pools (Authenticator "metric").At the unit (NPU) level, up to two pools (with different priorities), each with up to 10 ASN-GWs, can be defined (see “Managing the BTS Load Balancing Parameters” on page 227). Each BS defined in the unit will “inherit” these pools. It should be noted that the ASN-GW defined in the BS as the default authenticator (see “Managing Authentication Relay Parameters” on page 592) will be automatically added to Pool1 that is the higher priority pool (if not included already).At the BS level, you can enable/disable the use of each of the two pools. Note that if both pools are disabled, or if the enabled pool(s) are empty, the ASN-GW load balancing feature is disabled and only the default authenticator will be used.This section includes:“Enabling the ASN-GW Load Balancing Configuration Mode” (Section 3.9.25.1).“Enabling/Disabling an ASN-GW Load Balancing Pool” (Section 3.9.25.2).“Restoring the Default Configuration of ASN-GW Load Balancing Pools” (Section 3.9.25.3).“Displaying Configuration Information for ASN-GW Load Balancing Pools” (Section 3.9.25.4).3.9.25.1 Enabling the ASN-GW Load Balancing Configuration ModeTo configure the ASN-GW Load Balancing parameters, first enable the ASN-GW Load Balancing configuration mode. Run the following command to enable the ASN-GW Load Balancing configuration mode. npu(config-bs-66053)# asNGWLoadBalancing](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-92.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 640 System Manual3.9.25.2 Enabling/Disabling an ASN-GW Load Balancing PoolAfter enabling the ASN-GW Load Balancing configuration mode, run the following command to enable/disable ASN-GW load balancing pools:npu(config-bs-5-ASNGWLoadBalancing)# asNGWLoadBalancing [asn-gw-pool-1 {enable | disable} ] [asn-gw-pool-2 {enable| disable} ]Note: After enabling Pool 1 and/or Pool 2, the AU must be reset to apply the change.Command Syntaxnpu(config-bs-66053)# asNGWLoadBalancingPrivilege Level10Command Modesbs configuration modeCommand Syntaxnnpu(config-bs-5-ASNGWLoadBalancing)# asNGWLoadBalancing [asn-gw-pool-1 {enable | disable} ] [asn-gw-pool-2 {enable| disable} ] Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values[asn-gw-pool-1 {enable | disable} ]Enable/disable the use of pool 1Optional Enable EnableDisable[asn-gw-pool-2 {enable | disable} ]Enable/disable the use of pool 2.Pool 2 cannot be enabled if Pool 1 is disabled.Optional Enable EnableDisableCommand Modesbs asn-gw load balancing configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-93.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 641 System Manual3.9.25.3 Restoring the Default Configuration of ASN-GW Load Balancing PoolsAfter enabling the ASN-GW Load Balancing configuration mode, run the following command to restore the default configuration of ASN-GW load balancing pools:npu(config-bs-5-ASNGWLoadBalancing)# no ASNGWLoadBalancing [asn-gw-pool-1 ] [asn-gw-pool-2 ] Specify a pool to restore the configuration of this pool to the default value (enabled).Do not specify any pool to restore the configuration of both pools to the default value (enabled).3.9.25.4 Displaying Configuration Information for ASN-GW Load Balancing PoolsTo display configuration information of ASN-GW Load Balancing Pool, run the following command:Command Syntaxnpu(config-bs-5-ASNGWLoadBalancing)# no ASNGWLoadBalancing [asn-gw-pool-1 ] [asn-gw-pool-2 ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values[asn-gw-pool-1 ] Specify pool 1 to return the configuration of this pool to the default value (enabled)Optional N/A asn-gw-pool-1[asn-gw-pool-2 ] Specify pool 2 to return the configuration of this pool to the default value (enabled)Optional N/A asn-gw-pool-2Command Modesbs asn-gw load balancing configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-94.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 642 System Manualnpu# show ASNGWLoadBalancing bs [<(1 to 16777215 StepSize 1)> ]Specify the BS ID if you want to display information for a particular BS. For example, to display the ASN-GW Load Balancing configuration parameters of BS 66053, run the following command:npu# show ASNGWLoadBalancing bs 66053Do not specify this parameter if you want to view information for all existing BSs. To display information for all BSs, run the following command:npu# show ASNGWLoadBalancing bs3.9 .26 Managing Beam Forming ParameterThe Beam Forming Calibration Attenuator parameter is applicable only if the Downlink Diversity Mode parameter is set to Beam Forming (see “Configuring the Airframe Downlink Diversity Mode Parameter” on page 568).3.9.26.1 Enabling the Beam Forming Configuration ModeFrom the BS configuration mode, run the following command:npu(config-bs-66053)# beamformCommand SyntaxASNGWLoadBalancing bs [<(1 to 16777215 StepSize 1)> ]Privilege Level1Display Format (for each existing BS if requested for all BSs)BSIDLSB : <value>ASN-GWPoolPrimary : <enable(1)/disable(2)>ASN-GWPoolSecondary : <enable(1)/disable(2)>Command ModesGlobal command modeTo enable the Beam Forming Configuration Mode:](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-95.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 643 System ManualAfter enabling the Beam Forming configuration mode, you can execute the following tasks:Configure the Beam Forming parameter (refer to Section 3.9.26.2).Restore the default values of the Beam Forming parameter (refer to Section 3.9.26.3).You can display configuration value for the beamforming parameter of a selected or all existing BSs (refer to Section 3.9.26.4).3.9.26.2 Configuring the Beam Forming ParameterFrom the beamforming configuration mode, run the following command:npu(config-bs-66053-beamform)# beamform [cal-atten {noAttenUsed | lowAtten | highAtten} ] To configure the Beam Forming parameter:Command Syntaxnpu(config-bs-66053)# beamform [cal-atten {noAttenUsed | lowAtten | highAtten} ] Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Valuescal-atten {noAttenUsed | lowAtten | highAttenApplicable only in Beam Forming DL Diversity Mode. The calibration attenuation used to help mitigate potential out of band interference to beam forming calibration caused by other base stations.Optional lowAtten noAttenUsedlowAttenhighAttenCommand Modesbs beamform configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-96.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 644 System Manual3.9.26.3 Restoring the Default Value of the Beam Forming ParameterTo restore the default values of the Beam Forming parameters, run the following command:npu(config-bs-66053)# no beamform [cal-atten ]3.9.26.4 Displaying Configuration Information for Beam Forming ParameterTo display configuration information of the Beam Forming parameters, run the following command:npu# show beamform bs [<(1 to 16777215 StepSize 1)Specify the BS ID if you want to display information for a particular BS. For example, to display the Beam Forming parameter of BS 66053, run the following command:npu# show beamform bs 66053Do not specify this parameter if you want to view information for all existing BSs. To display information for all BSs, run the following command:npu# show beamform bsCommand Syntaxnpu(config-bs-66053)# no beamform [cal-atten ]Privilege Level10Command Modesbs beamform configuration modeCommand Syntaxnpu# show beamform bs [<(1 to 16777215 StepSize 1)Privilege Level1](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-97.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing BSs4Motion 645 System ManualSyntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>The BS ID Specify a value for this parameter if you want to display parameters of a specific BS. Do not specify a value for this parameter if you want to display parameters of all BSs.Optional N/A 1-16777215Display Format(for each existing BS if requested for all BSs)BSIDLSB :<value>CalibrationAttenuator :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-98.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 646 System Manual3.10 Ma na ging Sect orsUp to 6 Sector objects can be created and configured. The Sector’s configuration includes the association of all the objects that form a sector, including BS, AU/AU-Port, ODU/ODU-Port and Antenna/Antenna Port.This section include:“Configuring Sector Parameters”, Section 3.10.1“Configuring Sector Association Entries”, Section 3.10.23.1 0 .1 Configuring Sector Para m e t e rs1Enable the Sector Parameters configuration mode for the selected Sector (refer to Section 3.10.1.1)2You can now execute any of the following tasks:»Configure one or more of the parameters tables of the Sector (refer to Section 3.10.1.2)»Restore the default values of parameters in one or more of the parameters tables of the Sector (refer to Section 3.10.1.3)3Terminate the Sector Parameters configuration mode (refer to Section 3.10.1.4)In addition, you can, at any time, display configuration information for each of the parameters tables of the Sector (refer to Section 3.10.1.6) or delete an existing Sector object (refer to Section 3.10.1.5). 3.10.1.1 Enabling the Sector Parameters Configuration Mode\Creating a Sector ObjectTo configure the parameters of a Sector, first enable the Sector Parameters configuration mode for the specific Sector. Run the following command to enable the Sector Parameters configuration mode for an existing Sector object:npu (config)# sector-params <(1 to 6 StepSize 1)> To configure Sector Parameters:](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-99.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 647 System ManualTo create a new Sector object, the width parameter must be specified. Run the following command to create a new Sector object and enable the parameters configuration mode for this ODU:npu (config)# sector-params <(1 to 6 StepSize 1)> [width <(0 to 359 StepSize 1)>]A new Sector object is created with default values for all parameters except to the mandatory width parameter.For example, to create Sector 1 object and enable the parameters configuration mode for this Sector, where the width is 90 degrees, run the following command:npu (config)# sector-params 1 width 90After enabling the Sector Parameters configuration mode for a Sector you can execute any of the following tasks:Configure one or more of the parameters tables of the Sector (refer to Section 3.10.1.2)Restore the default values of non-mandatory parameters in one or more of the parameters tables of the Sector (refer to Section 3.10.1.3)After executing the above tasks, you can terminate the Sector Parameters configuration mode (refer to Section 3.10.1.4) and return to the global configuration mode.IMPORTANTAn error may occur if you provide an invalid value for any of these parameters. Refer the syntax description for more information about the appropriate values and format for configuring these parameters.Command Syntaxnpu (config)# sector-params <(1 to 6 StepSize 1)> [ width <(0 to 359 StepSize 1)> ]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-100.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 648 System Manual3.10.1.2 Configuring Sector ParametersAfter enabling the Sector Parameters configuration mode you can configure the following parameters tables:Sector Definition (refer to Section 3.10.1.2.1)Sector Reserved (refer to Section 3.10.1.2.2)3.10.1.2.1 Configuring Sector Definition ParametersThe Sector Definition table enables configuring the main properties of the Sector.To configure the Sector Definition parameters, run the following command:npu(config-sector-params-1)# sector-definition [sector-name <string (32)>] [heading <(0 to 359 StepSize 1)>] [width <(0 to 359 StepSize 1)>]<(1 to 6 StepSize 1)> The Sector ID Mandatory N/A 1-6width <(0 to 359 StepSize 1)>The planned sector coverage, in degrees.Mandatory when creating a new SectorN/A 0 - 359Command ModesGlobal configuration modeNOTEThe following examples are for sector-1 parameters configuration mode.IMPORTANTAn error may occur if you provide an invalid value for any of these parameters. Refer the syntax description for more information about the appropriate values and format for configuring these parameters.Command Syntaxnpu(config-sector-params-1)# sector-definition [sector-name <string (32)> ] [heading <(0 to 359 StepSize 1)> ] [width <(0 to 359 StepSize 1)> ]Privilege Level10](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-101.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 649 System Manual3.10.1.2.2 Configuring Sector Reserved ParametersAs the name implies, the reserved parameters table enables configuring up to 4 parameters that are reserved for possible future use. In the current release none of the reserved parameters is being used.To configure the Sector Reserved parameters, run the following command:npu(config-sector-params-1)# sector-reserved [reserved-1 <string (32)>] [reserved-2 <string (32)>] [reserved-3 <string (32)>] [reserved-4 <string (32)>].Syntax Description Parameter Description Presence Default ValuePossible Valuessector-name <string (32)>The sector name (description). Must be unique in the site (shelf).Optional null (empty string)A string of up to 32 charactersheading <(0 to 359 StepSize 1)>The sector heading (The center angle of the sector), in degrees.Optional 0 0 - 359width <(0 to 359 StepSize 1)>The planned sector coverage, in degrees.Optional Configured previously during sector creation.0 - 359Command Modessector-params configuration modeCommand Syntaxnpu (config-sector-params-1)# sector-reserved [reserved-1 <string (32)>] [reserved-2 <string (32)>] [reserved-3 <string (32)>] [reserved-4 <string (32)>]Privilege Level10](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-102.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 650 System Manual3.10.1.3 Restoring Default Values for Sector Configuration ParametersAfter enabling the Sector Parameters configuration mode you can restore the default values for parameters in the following parameters tables:Sector Definition (refer to Section 3.10.1.3.1)Sector Reserved (refer to Section 3.10.1.3.2)3.10.1.3.1 Restoring the Default Values of Sector Definition ParametersTo restore the one or all of the non-mandatory parameters to the default values, run the following command:npu(config-sector-params-1)# no sector-definition [sector-name] [heading]Run the following command to restore the sector definition parameters to the default values: npu(config-sector-params-1)# no sector-definitionSyntax Description Parameter Description Presence Default ValuePossible Values[reserved-N <string (32)>] (N=1-4)Reserved parameter number N Optional null (an empty string)A string of 32 printable characters.Command Modessector-params configuration modeNOTERefer to Section 3.10.1.2.1 for a description and default values of these parameter.Command Syntaxnpu(config-sector-params-1)# no sector-definition [sector-name] [heading]Privilege Level10](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-103.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 651 System Manual3.10.1.3.2 Restoring the Default Values of Sector Reserved ParametersTo restore Sector Reserved parameters to their default value, run the following command:npu(config-sector-params-1)# no sector-reserved [reserved-1] [reserved-2] [reserved-3] [reserved-4]You can restore only selected parameters to their default value by specifying only those parameter. For example, to restore only the reserved-1 parameter to its default values, run the following command:npu(config-sector-params-1)# no sector-reserved reserved-1This parameter will be restored to the default value, while the other parameters will remain unchanged.To restore all parameters to their default value, run the following command:npu(config-sector-params-1)# no sector-reserved3.10.1.4 Terminating the Sector Parameters Configuration ModeRun the following command to terminate the Sector Parameters configuration mode:npu(config-sector-params-1)# exitCommand Modessector-params configuration modeNOTERefer to Section 3.10.1.2.2 for a description and default values of these parameters.Command Syntaxnpu(config-sector-params-1)# no sector-reserved [reserved-1] [reserved-2] [reserved-3] [reserved-4]Privilege Level10Command Modessector-params configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-104.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 652 System Manual3.10.1.5 Deleting a Sector ObjectRun the following command to delete a Sector object:npu(config)# no sector-params <(1 to 6 StepSize 1)>3.10.1.6 Displaying Configuration Information for Sector ParametersYou can display the current configuration and (where applicable) additional status information for the following parameters tables:Sector Definition (refer to Section 3.10.1.6.1)Command Syntaxnpu(config-sector-params-1)# exitPrivilege Level10Command Modessector-params configuration modeIMPORTANTAn associated Sector (specified in a Sector Association) cannot be deleted.Command Syntaxnpu(config)# no sector-params <(1 to 6 StepSize 1)>Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values <(1 to 6 StepSize 1)> The Sector ID Mandatory N/A 1-6Command ModesGlobal configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-105.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 653 System ManualSector Reserved (refer to Section 3.10.1.6.2)3.10.1.6.1 Displaying Configuration Information for Sector Definition ParametersTo display configuration information for the Sector Definition parameters of a specific or all Sector objects, run the following command:npu# show sector-definition [sector-id <(1 to 6 StepSize 1)>]Specify the Sector ID (1-6) if you want to display configuration information for a particular Sector. Do not specify a value for this parameter if you want to view configuration information for all existing Sector objects.Command Syntaxnpu# show sector-definition [sector-id <(1 to 6 StepSize 1)> ]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Valuessector-id <(1 to 6 StepSize 1)> The Sector ID Specify a value for this parameter if you want to display the Sector Definition parameters of a specific Sector. Do not specify a value for this parameter if you want to display the parameters of all Sectors.Optional N/A 1-6Display Format(for each existing ODU object if requested for all ODUs)SectorID :<value>SectorName :<value>SectorHeading(degrees) :<value>SectorWidth(degrees) :<value>](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-106.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 654 System Manual3.10.1.6.2 Displaying Configuration Information for Sector Reserved ParametersTo display configuration information for the reserved parameters of a specific or all Sector objects, run the following command:npu# show sector-reserved [sector-id <(1 to 6 StepSize 1)>]Specify the Sector ID (1-6) if you want to display configuration for a particular Sector. Do not specify a value for this parameter if you want to view configuration for all existing Sector objects.Command ModesGlobal command modeCommand Syntaxnpu# show sector-reserved [sector-id <(1 to 6 StepSize 1)> ]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 6 StepSize 1)>The Sector ID.Specify a value for this parameter if you want to display the reserved parameters of a specific Sector. Do not specify a value for this parameter if you want to display the reserved parameters of all Sectors.Optional N/A 1-6Display Format(for each existing ODU object if requested for all ODUs)SectorID :<value>ReservedParameter1 :<value>ReservedParameter2 :<value>ReservedParameter3 :<value>ReservedParameter4 :<value>](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-107.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 655 System Manual3.1 0 .2 Configuring Sector Associat ion Entrie sThe Sector Association entry defines all the components that together form a Sector. Because of the unique functionality of Sector Association entries, they can only be created: An existing Sector Association entry cannot be modified (to modify an entry, it must first be deleted and then created again with the modified values). For details on creating a new Sector Association entry, refer to Section 3.10.2.1.You can, at any time, display configuration information for each or all of the Sector Association entries (refer to Section 3.10.2.3) or delete an existing Sector Association entry (refer to Section 3.10.2.2). 3.10.2.1 Creating a Sector Association EntryA Sector Association entry is identified by the BS ID, AU Slot ID and AU Port Number.To create a new Sector Association entry, all the entry’s parameters must be specified. Run the following command to create a new Sector Association entry:npu (config)# sector-assoc <(1 to 16777215 StepSize 1)> <(1 to 4 StepSize 1) | (7 to 9 StepSize 1)> <(1 to 4 StepSize 1)> sector-id <(1 to 6 StepSize 1)> odu-no <(1 to 28 StepSize 1)> odu-port-no <1 to 4 StepSize 1> antenna-no <(1 to 28 StepSize 1)> antenna-port-no <1 to 8 StepSize 1>A new Sector Association entry is created with the specified values. For example, to create a Sector Association entry identified by BS ID 66053, AU Slot No. 2 and AU Port No. and with association to Sector ID 3, ODU No. 4, Antenna No. 5, ODU Port No. 1 and Antenna Port No. 1, run the following command:npu (config)# sector-assoc 66053 2 1 sector-id 3 odu-no 4 odu-port-no 1 antenna-no 5 antenna-port-no 1Command ModesGlobal command modeCommand Syntaxnpu (config)# sector-assoc <(1 to 16777215 StepSize 1)> <(1 to 4 StepSize 1) | (7 to 9 StepSize 1)> <(1 to 4 StepSize 1)> sector-id <(1 to 6 StepSize 1)> odu-no <(1 to 28 StepSize 1)> odu-port-no <1 to 4 StepSize 1> antenna-no <(1 to 28 StepSize 1)> antenna-port-no <1 to 8 StepSize 1>Privilege Level10](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-108.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 656 System ManualCreation of a new Sector Association entry will succeed only if all the following conditions are met:The specified BS object exists and is properly configured (see also Section 3.9):»All mandatory parameters have been configured properly.»The configured frequency is within the valid range defined by the required ODU type in the specified ODU object and the bandwidth parameter.»The Operator ID is the same as Operator ID configured for previously associated BSs.»In all tables that includes only non-mandatory parameters at least one parameter has been configured.»Wherever needed, the apply command has been executed.Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>BS ID (bs-id-lsb) Mandatory N/A 1-16777215<(1 to 4 StepSize 1) | (7 to 9 StepSize 1)>AU Slot ID Mandatory N/A 1-4, 7-9<(1 to 4 StepSize 1)> AU Port Number Mandatory N/A 1-4sector-id <(1 to 6 StepSize 1)>Sector ID Mandatory N/A 1-6odu-no <(1 to 28 StepSize 1)>ODU Number Mandatory N/A 1-28odu-port-no <1 to 4 StepSize 1>ODU Port Number Mandatory N/A 1-4antenna-no <(1 to 28 StepSize 1)>Antenna Number Mandatory N/A 1-28antenna-port-no <1 to 8 StepSize 1>Antenna Port Number Mandatory N/A 1-4Command ModesGlobal configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-109.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 657 System ManualThe specified AU object exists (see Section 3.6).The specified ODU object exists (the mandatory parameters required-type and txpower for port 1 have been configured). The configured txpower is within the valid range for the required ODU type (see Section 3.7).The Antenna object exists (the mandatory heading parameter has been configured). The specified Antenna Port No. is within the range defined by the no-of-ports parameter (see Section 3.8).The Sector object exists (mandatory width parameter have been configured). The defined sector-name is unique in the site (shelf). An ODU Port (combination of ODU No. and ODU Port No.) cannot appear in more than one entry.An AU Port (combination of AU Slot No. and AU Port No.) cannot appear in more than one entry.An Antenna Port (combination of Antenna No. and Antenna Port No.) cannot appear in more than one entry.A specific Antenna can only be associated with a single Sector.In the current release, a specific BS can only be associated with a single AU, and vice versa (If BS 66053 is associated with AU 1, BS 66053 cannot be associated with another AU, and AU 1 cannot be associated with another BS).Two ODUs associated with the same AU (for Beam Forming support) must be in the same frequency band. This is applicable for 2x2 and 4x2 ODUs that support Beam Forming.3.10.2.2 Deleting a Sector Association EntryRun the following command to delete a Sector Association entry:npu (config)# no sector-assoc <(1 to 16777215 StepSize 1)> <(1 to 4 StepSize 1) | (7 to 9 StepSize 1)> <(1 to 4 StepSize 1)>Command Syntaxnpu (config)# no sector-assoc <(1 to 16777215 StepSize 1)> <(1 to 4 StepSize 1) | (7 to 9 StepSize 1)> <(1 to 4 StepSize 1)>](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-110.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 658 System ManualNote that if all Sector Association entries with a particular BS are deleted (meaning the BS is no longer in use), this BS should be removed from all relevant Neighbor BS lists of other BSs.3.10.2.3 Displaying Configuration Information for Sector Association EntriesTo display configuration information of a specific or all Sector Association entries, run the following command:npu# show sector-assoc [bs-id-lsb <(1 to 16777215 StepSize 1)> au-slot-no <(1 to 4StepSize 1) | (7 to 9 StepSize 1)> au-port-no <(1 to 4 StepSize 1)>]Specify the BS ID (bs-id-lsb), AU Slot No. (au-slot-no) and AU Port number (au-port-no) if you want to display configuration information for a particular Sector Association entry. Do not specify values for these parameters if you want to view configuration information for all existing Sector Association entries.Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values<(1 to 16777215 StepSize 1)>BS ID (bs-id-lsb) Mandatory N/A 1-16777215<(1 to 4 StepSize 1) | (7 to 9 StepSize 1)>AU Slot ID Mandatory N/A 1-4, 7-9<(1 to 4 StepSize 1)> AU Port Number Mandatory N/A 1-4Command ModesGlobal configuration modeCommand Syntaxnpu# show sector-assoc [bs-id-lsb <(1 to 16777215 StepSize 1)> au-slot-no <(1 to 4StepSize 1) | (7 to 9 StepSize 1)> au-port-no <(1 to 4 StepSize 1)> ]Privilege Level1](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-111.png)
![Chapter 3 - Operation and Administration of the Macro BTS Managing Sectors4Motion 659 System ManualSyntax Description Parameter Description Presence Default ValuePossible Values<bs-id-lsb (1 to 16777215 StepSize 1)>BS IDSpecify only if you want to display configuration of a particular Sector Association entry.Optional N/A 1-16777215<(1 to 4 StepSize 1) | (7 to 9 StepSize 1)>AU Slot IDSpecify only if you want to display configuration of a particular Sector Association entry.Optional N/A 1-4, 7-9<(1 to 4 StepSize 1)>AU Port NumberSpecify only if you want to display configuration of a particular Sector Association entry.Optional N/A 1-4Display Format(for each existing ODU Port if requested for all ODU Ports)BSIDLSB :<value>AUSlotNo. :<value>AUPortNo. :<value>SectorID :<value>ODUNo. :<value>ODUPortNo. :<value>AntennaNo. :<value>AntennaPortNo. :<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-112.png)
![Chapter 3 - Operation and Administration of the Macro BTS Monitoring HW and SW Components4Motion 660 System Manual3.11 Monitoring HW and SW Compone ntsThis section describes the procedures for:“Monitoring Hardware Components” on page 660“Displaying System Files” on page 6673.1 1 .1 Monit oring Ha rdw are Com ponent sYou can use the CLI to monitor performance of the following hardware components with respect to:“Displaying the Card Types Installed in Shelf Slots 1 - 9” on page 660“Displaying the Current Status of Shelf Components” on page 661“Displaying the Temperature of the Shelf” on page 663“Displaying Utilization of CPU and Memory Resources for the NPU” on page 664“Displaying Packets Discarded Via Rate Limiting” on page 6653.11.1.1 Displaying the Card Types Installed in Shelf Slots 1 - 9To view the types of cards that are currently installed in slots 1-9 of the shelf run the following command:npu# show shelf-viewCommand Syntaxnpu# show shelf-viewPrivilege Level1](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-113.png)
![Chapter 3 - Operation and Administration of the Macro BTS Monitoring HW and SW Components4Motion 661 System Manual3.11.1.2 Displaying the Current Status of Shelf ComponentsYou can view the current status of the following shelf components:NPUPSUPIUAVU or (specific fan)To view the current status of all shelf components, run the following command:npu# show shelf status [{NPU | PSU [<slot id (1-4)>] |PIU [<slot id (1-2)>] | AVU | Fan [<fan_num (1-10)>]}]For example, run the following command to view the status of the PSU, slot# 4:npu# show shelf status PSU 4To view the status of all the shelf components, run the following command:Display Format Slot# Card Type 1 <notInstalled/au4x4Modem/other> 2 <notInstalled/au4x4Modem/other> 3 <notInstalled/au4x4Modem/other> 4 <notInstalled/au4x4Modem/other> 5 npu 6 notInstalled 7 <notInstalled/au4x4Modem/other> 8 <notInstalled/au4x4Modem/other> 9 <notInstalled/au4x4Modem/other>Command ModesGlobal command modeNOTERefer Figure 3-1 for more information about the slot IDs assigned to each shelf component.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-114.png)
![Chapter 3 - Operation and Administration of the Macro BTS Monitoring HW and SW Components4Motion 662 System Manualnpu# show shelf statusThe displayed information includes the following details:NPU:»Slot#: 5»PrsntState: Installed»HWVersion:»HWRevision:»SerialNumAVU»PrsntState: Installed/Not Installed»HlthState:Healthy/FaultyCommand Syntaxnpu# show shelf status [{NPU | PSU [<slot id (1-4)>] |PIU [<slot id (1-2)>] | AVU | Fan [<fan_num (1-10)>]}]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values[{NPU | PSU [<slot id (1-4)>] |PIU [<slot id (1-2)>] | AVU | Fan [<fan_num (1-10)>]}Indicates the shelf components for which you want to display the current status. Do not specify any component to view the status of all components.Optional N/A NPUPSU <1-4>PIU <1-2>AVUFan <(1-10>](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-115.png)
![Chapter 3 - Operation and Administration of the Macro BTS Monitoring HW and SW Components4Motion 663 System ManualFAN:»FAN#: (1-10)»HlthState:Healthy/FaultyPIU»Slot# (1-2)»AdmnState: Yes/No»ReqHWVer: The configured HW Version- 5 (58A) or 6 (35A)»PrsntState: Installed/Not Installed»HlthState:Healthy/Faulty»OperState: Active/Non-active»InstHWVer: The installed HW Version- 5 (58A,) 6 (35A) or 7 (not installed)PSU»Slot# (1-4)»AdmnState: Yes/No»PrsntState: Installed/Not Installed»HlthState:Healthy/Faulty»OperState: Running/Down3.11.1.3 Displaying the Temperature of the ShelfTo view the current temperature inside the unit, run the following command:npu# show shelf temperatureCommand Syntaxnpu# show shelf temperature](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-116.png)
![Chapter 3 - Operation and Administration of the Macro BTS Monitoring HW and SW Components4Motion 664 System Manual3.11.1.4 Displaying Utilization of CPU and Memory Resources for the NPUTo display the utilization of CPU and memory resources for the NPU, run the following command:npu# show resource usageAfter you run this command, the current CPU and memory usage is displayed.Privilege Level1Display FormatCurrent shelf temperature: <value> [Celsius] / <value> [Farenheit]Command ModesGlobal command modeNOTEFor more information about setting thresholds for CPU and memory usage, refer to “Displaying CPU and Memory Utilization Limits for the NPU” on page 173.Command Syntaxnpu# show resource usagePrivilege Level1Display FormatResource Usage[in %]CPU <value>Memory 7<value>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-117.png)
![Chapter 3 - Operation and Administration of the Macro BTS Monitoring HW and SW Components4Motion 665 System Manual3.11.1.5 Displaying Packets Discarded Via Rate LimitingTo retrieve the number of packets discarded because of rate limiting for a specific or all applications (pre-defined, user-defined or all), run the following command:npu# show rate-limit counters {ftp | telnet | tftp | ssh | icmp | snmp | R4-R6 | igmp | eap | arp | all-others | <user-defined-app> | all}NOTEFor more information about configuring rate limiting, refer to “Rate Limiting for the NPU” on page 174.Command Syntaxnpu# show rate-limit counters {ftp | telnet | tftp | ssh | icmp | snmp | R4-R6 | igmp | eap | arp | all-others | <user-defined-app> | all}Privilege Level1](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-118.png)
![Chapter 3 - Operation and Administration of the Macro BTS Monitoring HW and SW Components4Motion 666 System ManualSyntax Description Parameter Description Presence Default ValuePossible Values{ftp | telnet | tftp | ssh | icmp | snmp | R4-R6 | igmp | eap | arp | all-others | <user-defined-app> | all}Indicates the application for which packets discarded by rate limiting are to be displayed. Optional N/A ftptelnettftpsshicmpsnmpR4-R6igmpeaparpall-others: Refers to all other applications that may send packets to the CPU, and are not in the list of pre-defined or user-defined applications.<user defined>all: Refers to all applications that may attempt to send packets to the CPU.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-119.png)
![Chapter 3 - Operation and Administration of the Macro BTS Monitoring HW and SW Components4Motion 667 System Manual3.1 1 .2 Displaying Syst e m File sThe following system files reside in the TFTP boot directory of the NPU:Performance data files: Contain performance counters for system modules. (For more information about the modules for which you can configure collection and storage of performance data, refer to Section 3.4.14. These files are available in the path, /tftpboot/management/performance.System log: Contain log and trace messages. (For more information about configuring logging and tracing, refer to Section 3.12.1 and Section 3.4.13. These files are available in the path, /tftpboot/management/system_logs/.User history files: Contain information about the commands/tasks executed by the user. These files are available in the path, /tftpboot/management/user_log.In addition, Collected System Logs files with complete status and configuration details may also be available (for details refer to “Creating a Collected System Logs File” on page 396).To display a list of performance data, system log, active alarms, or user history files, run the following command:Display FormatRATELIMIT COUNTERS: Pre-defined applications--------------------------------------------Application Packets discarded <Application> <Number of Packets Discarded> <Application> <Number of Packets Discarded> SSH<Application> <Number of Packets Discarded> SNMPRATELIMIT COUNTERS: User-defined applications---------------------------------------------Application Packets discarded<Application> <Number of Packets Discarded>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-120.png)
![Chapter 3 - Operation and Administration of the Macro BTS Monitoring HW and SW Components4Motion 668 System Manualnpu# show saved {Performance | Active-alarm | Log | User-history} files [recent <1-65535>]For example, if you want to view the 30 most recently saved log files, residing in the TFTP boot directory of the NPU, run the following command:npu# show saved Log files recent 30To display a list of collected system logs files, run the following command:npu# show saved system logsCommand Syntaxnpu# show saved {Performance | Active-alarm | Log | User-history} files [recent <1-65535>]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible ValuesPerformance|Active-alarm|Log|User-historyIndicates the type of system files that are to be displayed:Mandatory N/A PerformanceActive-alarmLogUser-history[recent <1-65535>]Indicates the number of files to be displayed. The most recently saved files are displayed.If you do not specify a value for this parameter, all the files of a particular type are displayed.Optional N/A 1-65355Command ModesGlobal command modeCommand Syntaxnpu# show saved system logs](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-121.png)
![Chapter 3 - Operation and Administration of the Macro BTS Monitoring HW and SW Components4Motion 669 System ManualPrivilege Level1Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-122.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 670 System Manual3.12 Troubleshooting3.1 2 .1 Configuring TracingThe system can generate traces to be used for tracing the execution sequence of a module and determining the actual cause of an erroneous condition. Traces are recorded for events that occur with respect to the following system modules:System startup procedures: Refers to all procedures/events that occur during system startup.NPU/AU upgrade procedures: Refers to all the procedures executed while upgrading the NPU/AU.Fault management procedures: Refers to internal processes that are executed for monitoring erroneous conditions or fault conditions. System performance procedures: Refers to internal processes that are executed for monitoring system performance. Shelf management procedures: Refers to internal processes that are executed for monitoring the health and temperature of all hardware components (other than the NPU) such as the AU, PIU and PSU.WiMAX signaling protocols: Refers to all the protocols that implement the ASN-GW functionality.User interface: Refers to the command line or remote management interface used for executing all user-initiated events such as system shut down or reset.AU Manager: Refers to all internal processes used for fault, configuration, and performance management for AU.The system stores a maximum of 1000 trace and log messages, after which the oldest messages are overwritten. First configure system-level tracing, and then configure tracing separately for each module. This section describes the commands to be used for:“Managing System-level Tracing” on page 671“Configuring Module-level Tracing” on page 674](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-123.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 671 System Manual3.12.1.1 Managing System-level TracingSystem-level tracing refers all the procedures to be executed for managing tracing for the entire system. To manage system-level tracing: Enable/disable logging for the entire system and specify the destination (file or console) where traces are to be maintained.Make periodic backups of trace filesYou can, at any time, view the current destination to where traces are maintained. After you have enabled/disabled system-level logging and specified the destination for storing log messages, you can configure logging separately for each module. This section describes the commands to be used for:“Enabling System-level Tracing” on page 671“Disabling System-level Tracing” on page 673“Displaying the Current Status of Trace Destinations” on page 6733.12.1.1.1 Enabling System-level TracingYou can enable traces for all modules across the system and specify the destination where traces should be written. The destination can be either a file stored on the local system or console. To view whether tracing to file or console is enabled or disabled, refer Section 3.12.1.1.3.To enable system-level tracing, run the following command:npu(config)# trace destination {file|console}The system maintains a maximum of 1000 trace and log messages, after which the oldest messages are overwritten.NOTEBy default, system-level tracing to file is disabled. If you enable tracing to file, traces are written to the same file that contains log messages. This file is not maintained after system reset. It is recommended that you periodically make a backup of this file on the NPU flash. For details, refer to Section 3.4.13.1.5.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-124.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 672 System ManualNOTEAfter you have enabled system-level tracing, you can configure the types of traces (brief or detailed) to be generated for each module. By default, module-level tracing is disabled. To configure tracing for each module, refer to Section 3.12.1.2.IMPORTANTAn error may occur if:Tracing is already enabled for the requested destination (file or console).An internal error has occurred.Command Syntaxnpu(config)# trace destination {file|console}Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values{file|console} Indicates whether tracing to a file or console is to be enabled for the entire system.Mandatory N/A file: Indicates that system-level traces are to be written to a file.console: Indicates that the system-level traces are to be written to a console. Command ModesGlobal configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-125.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 673 System Manual3.12.1.1.2 Disabling System-level TracingTo disable tracing at the system-level, run the following command:npu(config)# no trace destination {file|console}3.12.1.1.3 Displaying the Current Status of Trace DestinationsTo view the current status of trace destinations, that is, whether the system is enabled/disabled for tracing to file or console, run the following command:npu(config)# show trace destinationIMPORTANTAn error may occur if:Tracing is already disabled for the requested destination (file or console).An internal error has occurred.Command Syntaxnpu(config)# no trace destination {file|console}Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values{file|console} Indicates whether tracing to file or console is to be disabled for the entire system.Mandatory N/A file: Indicates that tracing to file is to be disabled.console: Indicates that tracing to console is to be disabled.Command ModesGlobal configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-126.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 674 System Manual3.12.1.2 Configuring Module-level TracingAfter configuring module-level tracing, you can specify whether brief or detailed traces should be recorded for the following modules:System startup proceduresNPU/AU upgrade proceduresFault management proceduresSystem performance proceduresShelf Management proceduresWiMAX signaling protocolsUser interfaceAU Management proceduresIMPORTANTThis command may not be successfully executed if an internal error occurs while processing the result.Command Syntaxnpu(config)# show trace destinationPrivilege Level1Display Format Trace File : <Enabled/Disabled>Console : <Enabled/Disabled>Trace Server : <Enabled/Disabled>(ServerIP - <IP address>)Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-127.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 675 System ManualYou can also disable tracing for a particular module. This section describes the commands to be used for:“Configuring Trace Levels” on page 675“Disabling Module-level Tracing” on page 676“Displaying Trace Levels” on page 6773.12.1.2.1 Configuring Trace LevelsTo specify the trace level (brief or detailed) for each module, run the following command:npu(config)# trace level [{StartupMgr|SWDownload|FaultMgr|PerfMgr|ShelfMgr|SIGASN|UserIF|AUMgr}] {Brief|Detailed}The parameters in this command correspond to the system modules/procedures listed in the following table:Specify the module name if you want to configure the trace level separately for this module. If you do not specify the name of the module, the trace level that you configure in this command is applied to all modules. For example, run the following command if you want logs to be created for WiMAX signaling protocols when the trace level configured to Detailed:NOTEBy default, module-level tracing is disabled.Table 3-33: Modules for which Tracing can be EnabledParameter Refers to...StartupMgr System startup proceduresSWDownload Software upgrade proceduresFaultMgr Fault management proceduresShelfMgr Shelf management proceduresSIGASN WiMAX signaling protocolsUserIF User-initiated proceduresAUMgr Internal processes used for managing AUPerfMgr Performance management procedures](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-128.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 676 System Manualnpu(config)# trace level SIGASN Detailed3.12.1.2.2 Disabling Module-level TracingTo disable tracing for one or all modules, run the following command:npu(config)# no trace level [{StartupMgr|SWDownload|FaultMgr|PerfMgr|ShelfMgr|SIGASN|UserIF|AUMgr}]Specify the module if you want to disable tracing for that module. If you do not specify the name of the module, tracing is disabled for all modules.Command Syntaxnpu(config)# trace level [{StartupMgr|SWDownload|FaultMgr|PerfMgr|ShelfMgr|SIGASN|UserIF|AUMgr}] {Brief|Detailed}Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values[{StartupMgr|SWDownload|FaultMgr|PerfMgr|ShelfMgr|SIGASN|UserIF|AUMgr}]Indicates the name of the module for which the trace level is to be configured. If you do not specify any value for this parameter, the same trace level is applied to all modules. For more information about these parameters, refer Table 3-33.Optional N/A StartupMgrSWDownloadFaultMgrPerfMgrShelfMgrSIGASNUserIFAUMgr{Brief|Detailed}Indicates the trace level to be applied for a particular or all modules. Mandatory N/A BriefDetailedCommand ModesGlobal configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-129.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 677 System ManualFor example, run the following command if you want to disable tracing for WiMAX signaling protocols:npu(config)# no trace level SIGASN3.12.1.2.3 Displaying Trace LevelsTo view the trace levels configured for one or more modules, run the following command: npu(config)# show trace level [{StartupMgr|SWDownload|FaultMgr|PerfMgr|ShelfMgr|SIGASN|UserIF|AUMgr}]Command Syntaxnpu(config)# no trace level [{StartupMgr|SWDownload|FaultMgr|PerfMgr|ShelfMgr|SIGASN|UserIF|AUMgr}]Privilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values[{StartupMgr|SWDownload|FaultMgr|PerfMgr|ShelfMgr|SIGASN|UserIF|AUMgr}]Indicates the name of the module for which tracing is to be disabled. If you do not specify any value for this parameter, tracing is disabled for all functionalities. For more information about these parameters, refer Table 3-33.Optional N/A StartupMgrSWDownloadFaultMgrPerfMgrShelfMgrSIGASNUserIFAUMgr\Command ModesGlobal configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-130.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 678 System ManualSpecify the module for which you want to view the configured trace level. If you do not specify the name of the module, the trace levels configured for all modules is displayed.3.1 2 .2 Configuring Port MonitoringThe port monitoring feature enables you to mirror all incoming and outgoing traffic on an interface to another interface. You can configure one interface as the destination interface to which traffic from multiple interfaces can be mirrored. This section describes the commands to be executed for enabling/disabling port Command Syntaxnpu(config)# show trace level [{StartupMgr|SWDownload|FaultMgr|PerfMgr|ShelfMgr|SIGASN|UserIF|AUMgr}]Privilege Level1Syntax Description Parameter Description Presence Default ValuePossible Values[{StartupMgr|SWDownload|FaultMgr|PerfMgr|ShelfMgr|SIGASN|UserIF|AUMgr}]Indicates the name of the module for which you want to display the configured trace levels.If you do not specify any value for this parameter, the trace levels for all modules are displayed. For more information about these parameters, refer Table 3-33.Optional N/A StartupMgrSWDownloadFaultMgrPerfMgrShelfMgrSIGASNUserIFAUMgrDisplay FormatModule Name : Trace level<module name> : <Trace Level>Command ModesGlobal command mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-131.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 679 System Manualmonitoring for source and destination interfaces or displaying configuration information for a particular interface.To enable port monitoring, you are required to configure:Source interfaces: Refers to the FastEthernet or GigabitEthernet interface for which incoming, outgoing or both types of traffic is to be monitored. You can configure port monitoring for one or more source interfaces.Destination interface: Refers to the interface where the packets are sent for analysis.Direction of the traffic that is to be monitoredThe following table lists the interfaces that can be mirrored, and the port numbers mapping to these interfaces:This section describes the commands to be used for:“Enabling the Port Monitoring Session” on page 680“Disabling a Port Monitoring Session” on page 682“Displaying Configuration Information for Source and Destination Interfaces” on page 684Table 3-34: Interface to Ethernet Port MappingEthernet Port Interface Type Interface IDAU1 Fast Ethernet 0/1AU2 Fast Ethernet 0/2AU3 Fast Ethernet 0/3AU4 Fast Ethernet 0/4AU5 Fast Ethernet 0/5AU6 Fast Ethernet 0/6AU7 Fast Ethernet 0/7MGMT Fast Ethernet 0/8CASCD Gigabit Ethernet 0/9](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-132.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 680 System Manual3.12.2.1 Enabling the Port Monitoring SessionThe port monitoring session refers to the association of a destination interface with one or more source interfaces. You can monitor incoming, outgoing or both types of traffic that is mirrored from the source interface to the destination interface.Run the following command to enable port monitoring for a source or destination interface:npu(config)# monitor session { source interface <interface-type> <interface-id> [{ rx | tx | both }] | destination interface <interface-type > <interface-id>}For example, to configure the Gigabit Ethernet 0/9 interface as the destination interface, you can run the following command:monitor session destination interface gigabitethernet 0/9You can now run the following commands to mirror incoming traffic for the source interfaces, Fast Ethernet 0/1 and Fast Ethernet 0/3:npu(config)# monitor session source interface fastethernet 0/1 rxnpu(config)# monitor session source interface fastethernet 0/3 rx All incoming and outgoing traffic for the 0/1 and 0/3 interfaces will be mirrored to the 0/9 interface.NOTEFor the current release, only one monitor session can be set up. This means that only one destination can be configured for one or more source interfaces.IMPORTANTAn error may occur if:The interface ID of the source or destination port you have specified is invalid. Refer Table 3-34 for the interface ID corresponding to each interface type.The port specified as the source interface is already specified as the destination interface for another port or vice versa.Command Syntaxnpu(config)# monitor session { source interface <interface-type> <interface-id> [{ rx | tx | both }] | destination interface <interface-type > <interface-id>}](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-133.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 681 System ManualPrivilege Level10Syntax Description Parameter Description Presence Default ValuePossible Values{source interface <interface-type> <interface-id> | destination interface <interface-type > <interface-id>}Indicates whether port monitoring is to be enabled for a source or destination interface. Specify the interface type and interface ID for the interface to be configured.Mandatory N/A Interface type:fastethernetgigabitetherneInterface ID:0/1 (for Fast Ethernet AU 1 port)0/2 (for Fast Ethernet AU 2 port)0/3 (for Fast Ethernet AU 3 port)0/4 (for Fast Ethernet AU 4 port)0/5 (for Fast Ethernet AU 5 port)0/6 (for Fast Ethernet AU 6 port)0/7 (for Fast Ethernet AU 7 port)0/8 (for Fast Ethernet MGMT port)0/9 (for Gigabit Ethernet CSCD port){ rx | tx | both } Indicates whether the incoming, outgoing or both types of traffic is to be mirrored for the source interface.Optional Both rxtxboth](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-134.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 682 System Manual3.12.2.2 Disabling a Port Monitoring SessionYou can disable a port monitoring session for a source or destinations interface for which port monitoring is enabled. Run the following command to disable port monitoring for a source or destination interface:npu(config)# no monitor session [{source interface <interface-type> <interface-id> [{ rx | tx | both }]|destination interface <interface-type > < interface-id >}]Command ModesGlobal configuration modeIMPORTANTAn error may occur if:The interface ID of the source or destination port you have specified is invalid. Refer Table 3-34 for the interface ID corresponding to each interface type.Port monitoring is not enabled for the source or destination interface for which you are trying to disable port monitoring.Command Syntaxnpu(config)# no monitor session [{source interface <interface-type> <interface-id> [{ rx | tx | both }]|destination interface <interface-type > < interface-id >}]Privilege Level10](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-135.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 683 System ManualSyntax Description Parameter Description Presence Default ValuePossible Values[{source interface <interface-type> <interface-id> |destination interface <interface-type > < interface-id >}]Indicates whether port monitoring is to be disabled for a source or destination interface. Specify the interface type and interface ID for the interface to be configured.If source/destination interface types/id are not specified then all enabled port monitoring sessions will be disabled.Mandatory N/A Interface type:fastethernetgigabitetherneInterface ID:0/1 (for Fast Ethernet)0/2 (for Fast Ethernet)0/3 (for Fast Ethernet)0/4 (for Fast Ethernet)0/5 (for Fast Ethernet)0/6 (for Fast Ethernet)0/7 (for Fast Ethernet)0/8 (for Fast Ethernet)0/9 (for Gigabit Ethernet){ rx | tx | both } Indicates whether the incoming, outgoing or both types of traffic is to be disabled for mirroring for the source interface.Optional Both rxtxbothCommand ModesGlobal configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-136.png)
![Chapter 3 - Operation and Administration of the Macro BTS Troubleshooting4Motion 684 System Manual3.12.2.3 Displaying Configuration Information for Source and Destination InterfacesTo display configuration information for port monitoring, that is, the source and destination interfaces for which this feature is enabled, run the following command:npu# show port-monitoringCommand Syntaxnpu# show port-monitoringPrivilege Level1Display FormatPort Monitoring: enabled Monitor Port: Gi0/9Port Ingress-Monitoring Egress-Monitoring---- ------------------ ------------Fa0/1 <status> <status>Fa0/2 <status> <status>Fa0/3 <status> <status>Fa0/4 <status> <status>Fa0/5 <status> <status>Fa0/6 <status> <status>Fa0/7 <status> <status>Fa0/8 <status> <status> Gi0/9 <status> <status>Command ModesGlobal configuration mode](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-137.png)
![4ChapterOperation and Administration of the Micro BTS](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-138.png)
![Chapter 4 - Operation and Administration of the Micro BTS4Motion 686 System ManualIn T his Chapter:“Micro BTS System Management” on page 687“The Monitor Program” on page 688“IP Addresses Configuration” on page 691“The Main Menu” on page 692“BTS Menu” on page 693“Sector Menu” on page 706“BS Menu” on page 708“Equipment Menu” on page 735“GPS Menu” on page 740](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-139.png)
![Chapter 4 - Operation and Administration of the Micro BTS Micro BTS System Management4Motion 687 System Manual4.1 M icro BTS System Mana gement The Micro BTS can be managed using any of the following options:SNMP based management using AlvariSTAR/AlvariCRAFT (or another network management system customized to support management of the system).Using Telnet to access the embedded Monitor application via the Ethernet port.Accessing the embedded Monitor application locally via the MON port.This chapter describes how to manage the system using the Monitor application. For information on managing the system using AlvariSTAR/AlvariCRAFT refer to the applicable documentation.NOTEIt is not possible to manage the Base Transceiver Station via the wireless link (from the MS’s side).](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-140.png)
![Chapter 4 - Operation and Administration of the Micro BTS The Monitor Program4Motion 688 System Manual4.2 T he Monitor Progra m4.2 .1 Ac c e ssing the M onitor Program1Use the Monitor cable to connect the MON connector to the COM port of your ASCII ANSI terminal or PC. The COM port connector on the Monitor cable is a 9 pin D type plug.2Run a terminal emulation program, such as HyperTerminal™.3Set the communication parameters as shown in the following table:The password prompt is displayed. Enter the password and press the Enter key to get to the Main menu. The default password is “installer”.1The PC used for accessing the Monitor program should be configured according to the BTS Management Connectivity parameters (see “Connectivity” on page 694).2Run the Telnet program connecting to the IP address of the connected port. 3The Enter the password message is displayed. Enter the password and press the Enter key to get to the Main menu. The default password is “installer”.To access the Monitor program via the MON connector:Table 4-1: COM Port ConfigurationParameter ValueBaud Rate 9600Data Bits 8Stop Bits 1Parity NoneFlow Control Xon/XoffPort Connected COM portTo access the Monitor program using Telnet:](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-141.png)
![Chapter 4 - Operation and Administration of the Micro BTS The Monitor Program4Motion 689 System Manual4.2 .2 Using the M onitor ProgramThis section describes the Monitor program structure and navigation rules.Each menu or submenu specifies the unit type, the management IP address, the running SW version and a description of the menu.Each menu or submenu displays a list of numbered options. To access an option, enter the number of the required option at the > prompt.At any point in the program, you can use the Esc key to return to the previous menu (one level up) without applying any change.The first selectable item in most menus is the Show option, enabling to view the current configuration of the applicable parameters. For some menus some additional status information is displayed.For certain parameters, an updated value is applied only after reset or after entering a specific command. For these parameters, both Configured and Current values are displayed in relevant Show menus.The Update/Add options will display all applicable parameters line by line, allowing to conveniently edit all of them. The availability and/or value range of certain parameters may change according to the value selected for a previous parameter belonging to the same group. The current value is displayed for each parameter. To keep the current value - press Enter. To change it - enter a new value and press Enter. The new/modified configuration will take effect only after completing the configuration process for the all relevant parameters.Press the Tab key for context sensitive help text (where applicable).If an erroneous value was entered - the reason of the error or help text will be displayed, and the parameter entry text will be displayed again.Many menus include a Select By option, enabling to get a sub-menu for a selected entity according to the selection criteria. hen prompted to enter selection criteria, prs the Tab key to display the valid selection values.If the Monitor program is not used for the period of time defined by the Monitor Inactivity Time-out (see “Monitor Inactivity Timeout” on page 697), the session will be terminated automatically.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-142.png)
![Chapter 4 - Operation and Administration of the Micro BTS The Monitor Program4Motion 690 System ManualSelect the Exit option in the Main menu to exit the program and terminate the session.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-143.png)
![Chapter 4 - Operation and Administration of the Micro BTS IP Addresses Configuration4Motion 691 System Manual4.3 IP Addresse s Configuration4.3 .1 IP Address Configuration Restric t ions1The following IP addresses should not be used and will be rejected:0.0.0.0224.0.0.0 - 255.255.255.255 (Multicasts, RFC 3171 D, RFC 1700 E)4.3 .2 IP SubnetsIn a binary representation (32 bits) a Subnet Mask string must comprise a series of contiguous binary '1's starting from the MSB, followed by a series of contiguous binary '0's.Subnet Masks 0.0.0.0 (all zeros, meaning “nothing”) and 255.255.255.255 (all ones, meaning “this address only”) are illegal and will be rejected.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-144.png)
![Chapter 4 - Operation and Administration of the Micro BTS The Main Menu4Motion 692 System Manual4.4 T he Ma in MenuThe Main menu of the Monitor program includes the following options:1 - BTS (see “BTS Menu” on page 693)2 - Sector (see “Sector Menu” on page 706)3 - BS (see “BS Menu” on page 708)4 - Equipment (see “Equipment Menu” on page 735)5 - GPS (see “GPS Menu” on page 740)X - Exit (select to exit the Monitor program and terminate the Telnet session)](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-145.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 693 System Manual4.5 BTS M e nuThe BTS menu includes the following options:“General”“Connectivity”“Unit Control”“Management”4.5 .1 Ge neralThe BTS General submenu enables viewing the current values and updating the general BTS parameters. The BTS General parameters are:“BTS Number”“BTS Name”“BTS Address”“Contact Person”4.5.1.1 BTS NumberA BTS identifier for management purposes. Should be unique in the managed network.The range is from 1 to 999999.The default is 0. A different number (unique in the managed network) must be configured.4.5.1.2 BTS NameAn optional descriptive parameter. A string of up to 32 printable characters.The default is null (an empty string).4.5.1.3 BTS AddressAn optional descriptive parameter. A string of up to 70 printable characters.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-146.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 694 System ManualThe default is null (an empty string).4.5.1.4 Contact PersonAn optional descriptive parameter. A string of up to 32 printable characters.The default is null (an empty string).4.5 .2 ConnectivityThe Connectivity submenu includes the following options:“Management Interface”“ASN-GW Load Balancing Pools”“L1 & L2”4.5.2.1 Management InterfaceThe Management submenu enables viewing the current values and updating the Management interface parameters. The Management Interface parameters are:“VLAN ID”“Source IP Address”“IP Subnet mask”“802.1P Priority”“DSCP”“Next Hop Gateway”4.5.2.1.1 VLAN IDThe VLAN ID to be used with management traffic.Valid values are 11-100, 110-4094. The default is 12.4.5.2.1.2 Source IP AddressThe IP address of the Management interface.The default is 192.168.1.1.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-147.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 695 System Manual4.5.2.1.3 IP Subnet maskThe Subnet Mask of the Management interface.The default is 255.255.255.0.4.5.2.1.4 802.1P PriorityThe 802.1P (VLAN) Priority of management traffic.The range is 0-7.The default is 0.4.5.2.1.5 DSCPThe DSCP value of management traffic. The range is 0-63. The default is 0.4.5.2.1.6 Next Hop GatewayThe Default Gateway IP address of the Management interface.The default is 0.0.0.0 (must be changed to a valid value). The Default Gateway must be in the subnet of the IP Address.4.5.2.2 ASN-GW Load Balancing PoolsThe Load Balancing feature provides a WiMAX operator with the capability to build resilient ASN infrastructure using ASN-GW redundancy. Every BS is provisioned with two lists of redundant ASN-GWs (pools). The BS applies round-robin mechanism in order to pick an Authenticator for each MS that performs initial network entry. This should eventually distribute the load between Anchor ASN-GWs. Geographical site backup can be achieved by using different priority of ASN-GW pools (Authenticator "metric").At the unit (BTS) level, up to two pools (with different priorities), each with up to 10 ASN-GWs, can be defined. Each BS defined in the unit will “inherit” these pools.The ASN-GW Load Balancing Pools submenu includes two options: Primary Pool and Secondary Pool. Select the Primary or Secondary Pool option to view or update the pool’s content. The options available for each pool are:Show: Select this option to view the current content of the pool.Add: Select this option to add an address to the pool (up to a maximum of 10 addresses per pool). You will be prompted to define the index for the entry (a](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-148.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 696 System Manualunique number in the range from 1 to 10) before defining the ASN-GW IP address. An IP address must be unique per both pools.Select: Use this option to select an entry in the pool by it’s index. You can then view the entry’s IP address, update the IP address, or delete the entry.4.5.2.3 L1 & L2The L1 & L2 option enables viewing or updating the parameters of the Ethernet interface:Operational State: The read-only operational status of the port (Up or Down).Administrative State: The administrative status of the port (Up or Down).Auto Negotiation: The mode for negotiating the port speed and the duplex mode with the link partner (Auto or Manual). The default is Auto.Port Speed: The port speed to be used for the physical interface (valid values are 10, 100 or 1000 Mbps). Configurable only if Auto Negotiation is set to Manual. The default is 1000 Mbps.Duplex Mode: The duplex mode for the interface (Full-Duplex or Half Duplex). Configurable only if Auto Negotiation is set to Manual. The default is Full-Duplex.4.5 .3 Unit ControlThe Unit Control menu enables various general control functions such as resetting the BTS, managing the SW versions of the BTS and uploading/downloading configuration backup files.The Unit Control menu includes the following options:“Reset”“Monitor Inactivity Timeout”“SW Version Control”“TFTP Server”“Files Control”](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-149.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 697 System Manual“ShutDown Operation”4.5.3.1 ResetSelect this option to reset the BTS. To avoid unintentional reset, you will be prompted to confirm the reset request. Changes to some of the configurable parameters are applied only after reset.4.5.3.2 Monitor Inactivity TimeoutThe Monitor Inactivity Timeout (min) parameter determines the amount of inactive time following which the unit automatically exits the Monitor program. The time out duration can range from 0 to 60 minutes. 0 means no inactivity timeout.The default value is 10 minutes.4.5.3.3 SW Version ControlThe BTS can contain two SW versions:Operational: Each time the BTS resets it will reboot using the version defined as Operational.Shadow: Normally the Shadow version is the backup version. Each time a new SW File is downloaded to the BTS, it will be stored as a Shadow version, replacing the previous Shadow Version.The typical process of upgrading to a new SW version includes the following steps:1Download the new SW File to the BTS. It will be stored as the Shadow version.2Reset and run the BTS from its Shadow version. Note that at this stage, if a reset were to occur, the BTS will return to the previous Operational version.3If you want to continue using the new version, swap the Shadow and Operational versions. The new (currently running) version is now defined as Operational, and will be used each time the BTS reboots. The previous version is defined now as Shadow.Each SW version includes two identifiers:SW File, which is the name of the downloaded SW file. This name does not necessarily include clear identification of the SW version number.SW Version, which provides the SW version number.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-150.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 698 System ManualThe SW Version Control menu includes the following options:“SW Inventory”“SW Version Control”4.5.3.3.1 SW InventorySelect this option to view the current available versions and the running version:Operational SW Version NumberShadow SW Version NumberCurrent Running SW Source: Operational or Shadow4.5.3.3.2 SW Version ControlThe SW Version Control submenu includes the following options:“Show SW Versions”“Show Activation and Status Parameters”“Load to Shadow”“Reset and Run from Shadow”“Set Running Version as Operational”4.5.3.3.2.1 Show SW VersionsSelect this option to view the current available versions and the running version:Operational SW Version NumberShadow SW Version NumberCurrent Running SW Source: Operational or Shadow4.5.3.3.2.2 Show Activation and Status ParametersSelect this option to view the status of the last requested download operation.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-151.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 699 System Manual4.5.3.3.2.3 Load to ShadowThe Load to Shadow option enables initiating a process of loading a new SW file to the BTS. The loaded SW file will be stored as the new Shadow file.The IP address of the TFTP Server holding the SW file to be loaded is defined by the TFTP Server parameter (see “TFTP Server” on page 699) You will be prompted to enter the File Path And File Name (up to 80 characters)4.5.3.3.2.4 Reset and Run from ShadowSelect the Reset and Run from Shadow option to reset the BTS and run the Shadow version after power up. To avoid unintentional actions you will be prompted to confirm the request.4.5.3.3.2.5 Set Running Version as OperationalWhen the BTS is running the Shadow version (after selecting Reset and Run from Shadow), it will boot from the Operational version after the next reset. Select the Set as Operational option if you want to swap versions so that the running version will become the Operational version and will be the version to be used after reset. To avoid unintentional actions you will be prompted to confirm the request.4.5.3.4 TFTP ServerThe TFTP Server option enables viewing or updating the IP address of the TFTP server to be used for SW download.4.5.3.5 Files ControlThe Files Control submenu enables creating backup files of the BTS configuration and downloading a configuration file to the BTS.The Files Control menu includes the following menu options:“Restore”“Backup”“Backup Files”4.5.3.5.1 RestoreThe Restore submenu enables restoring a previously saved backup configuration. The Restore submenu includes the following options:4.5.3.5.1.1 Restore From External FileThe Restore From External File submenu includes the following options:](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-152.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 700 System ManualShow: Select this option to view the details of the last request for restoring a configuration file from an external TFTP server. The displayed details include:»File Name»TFTP Server IP Address»Process StatusUpdate: Select this option to initiate a new process of restoring a configuration file from an external TFTP server. You will be prompted to define the following parameters:»File Name: The path to and file name of the file to be downloaded. A string comprising 1 to 254 characters.»TFTP Server IP Address: The IP address of the TFTP Server from which the file should be loaded.»Start Download?: Select the download File option to initiate the process.4.5.3.5.1.2 Restore From Local Filehe Restore From Local File submenu includes the following options:Show: Select this option to view the details of the last request for restoring a configuration file from the unit’s memory. The displayed details include:»Restore From Local Backup: noAction or restoretoRAM»Local File NameNOTETo avoid loss of connectivity behind a router, the Management Connectivity parameters are not changed when loading a Full backup file to the BTS. The values of these parameters configured in the target BTS before the loading process, are maintained.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-153.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 701 System ManualUpdate: Select this option to initiate a new process of restoring a local configuration file. You will be prompted to define the following parameters:»Restore From Local Backup: Select noAction or restoretoRAM. If you selected restoretoRAM, you will be prompted to select the name of the local file.»Local File Name: The name of the local backup file to be restored. A string comprising 1 to 30 characters. Must be the name of one of the existing backup file (see “Backup Files” on page 701).4.5.3.5.2 BackupA backup file of the device’s configuration is created automatically every day. The Backup submenu enables defining the time of day for execution of the automatic backup process. You can also initiate a manual request for creation of a backup file. The BTS holds the last 3 backup files.The Backup menu includes the following options:Automatic Configuration Backup: Select to view the current Daily Backup Time or to update it. The default is 00:00 (midnight).Create Backup File: Select this option to initiate a request for creating a backup file of the current configuration or to view the status of last request for creating a backup file:»Update: Select to initiate creation of a backup file for the current configuration.»Show: Select to view the Process Status of last request for creating a backup file.4.5.3.5.3 Backup FilesThe Backup Files option enables the viewing the path to and file names of the current local backup files (up to 3). The file’s name includes its creation date and time in the format YYYYMMDDHHMM.xml.gz.4.5.3.6 ShutDown OperationThe ShutDown Operation submenu enables selecting one of the following options:shutdown: Select this option to shut down the system. To avoid unintentional shut down, you will be prompted to confirm the request.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-154.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 702 System Manualreset: Select this option to reset the BTS. To avoid unintentional reset, you will be prompted to confirm the reset request. Changes to some of the configurable parameters are applied only after reset.resettoFactoryDefault: Select this option to restore the factory default configuration of all BTS parameters. All parameters will revert to their default values after the next reset. To avoid unintentional action, you will be prompted to confirm the request. noAction: Select this option to exit the Shutdown Operation submenu without any action.resettoFactoryDefaultwithConnectivity: Select this option to restore factory default configuration without changing any of the parameters required for maintaining management connectivity to the unit. To avoid unintentional action, you will be prompted to confirm the request. The parameters that are maintained without any change include:»BTS Name»Management interfaces parameters»L1 & L2 parameters»SNMP Traps Managers configurations»Authorized Managers configurations4.5 .4 M ana gementThe Management menu includes the following options:IMPORTANTBefore shutting down the system, it is recommended that you save the configuration file. The last saved configuration is used for rebooting the system.After shutting down the system you cannot restart it from remote. To start up the unit (after shut down), switch off and then switch on the power supply, IMPORTANTReset to default configuration will affect the ability for remote management of the unit.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-155.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 703 System Manual“SNMP Traps Managers”“Authorized Managers”4.5.4.1 SNMP Traps ManagersUp to 5 SNMP Traps Managers can be defined. The SNMP Trap Managers menu includes the following options:“Show”“Add”“Select”4.5.4.1.0.1 ShowSelect this option to view the details of the currently defined SNMP Traps Managers.4.5.4.1.0.2 AddSelect this option to add a new SNMP Traps Manager. The SNMP Traps Manager parameters are:“IP Address”“Port Number”“Community”“Enable Traps Distribution”4.5.4.1.0.2.1IP AddressThe IP address of the Traps Manager.4.5.4.1.0.2.2Port NumberThe port number on which the Trap Manager will listen for messages from the Agent. The range is from 1 to 65535. The port on which the management system listens for traps is 162.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-156.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 704 System Manual4.5.4.1.0.2.3CommunityThe name of the SNMP Read Community used by the Trap Manager. Traps are sent toward those Managers for which this parameter is configured. A string of up to 10 printable characters, case-sensitive.4.5.4.1.0.2.4Enable Traps DistributionIndicates whether the sending of traps to the management station is enabled or disabled.4.5.4.1.0.3 SelectUse this option to select one of the existing SNMP Traps Managers by its IP address. You can then view the details of the selected manager, update its parameters (excluding the IP address) or delete it.The Selected Manager submenu includes the following options:Show: For viewing the details of the selected Manager.Update: For updating the properties of the selected Manager.Delete: For deleting the selected Manager from the database.4.5.4.2 Authorized ManagersAn SNMP Manager comprises a pair of SNMP Communities (Read Community and Write Community). A management station is permitted to manage the BTS using SNMP only if it uses one of the configured SNMP Communities (or a pair of SNMP Communities). A maximum of five SNMP Managers can be configured. The Authorized Managers submenu enables defining the properties of management stations that are allowed to manage the BTS using SNMP.The Authorized Manager submenu includes the following options:“Show”“Add”“Select”4.5.4.2.1 Show Select this option to view the details of all currently defined authorized managers.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-157.png)
![Chapter 4 - Operation and Administration of the Micro BTS BTS Menu4Motion 705 System Manual4.5.4.2.2 AddSelect this option to add a new authorized manager. Up to 5 Authorized Managers can be defined. The following parameters can be configured:“Manager Number”“Read Community”“Write Community”4.5.4.2.2.1 Manager NumberA unique number from 1 to 5.4.5.4.2.2.2 Read CommunityThe SNMP Read Community to be used by the Authorized Manager. A null Read Community means that the read (get) operation can only be performed using the Write Community.Valid Community strings: 1 to 32 printable characters, case sensitive.4.5.4.2.2.3 Write CommunityThe SNMP Write Community to be used by the Authorized Manager. A null Write Community means that the Authorized Manager has Read only access rights.Valid Community strings: 1 to 32 printable characters, case sensitive.4.5.4.2.3 SelectThis option enables selecting an existing authorized manager for viewing or updating its properties or for deleting it from the database. The selection is based on the authorized manager's number. The Selected Manager submenu includes the following options:Show: For viewing the details of the selected Manager.Update: For updating the properties of the selected Manager.Delete: For deleting the selected Manager from the database.NOTEThe Read and Write Communities are mandatory and both must be defined (other than null).Duplication of Communities pairs is not allowed (each pair must be unique).](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-158.png)
![Chapter 4 - Operation and Administration of the Micro BTS Sector Menu4Motion 706 System Manual4.6 Sec t or MenuThe unit supports a single sector.The Sector menu includes the following options:“Sector Definition”“Sector Association”4.6 .1 Se c t or De finitionThe Sector Definition menu enables viewing or modifying the sector description parameters which are informative descriptions for inventory purposes. The Sector Definition parameters are:4.6.1.1 NameThe sector name. An optional descriptive string of up to 32 printable characters. The default is null (an empty string).4.6.1.2 HeadingThe sector heading (the center angle of the sector), in degrees. The range is from 0 to 359.The heading of an associated Sector cannot be changed. The default is 0.4.6.1.3 WidthThe planned sector coverage, in degrees. The range is from 0 to 359. The default is 0.4.6 .2 Se c t or Associat ionThe sector association is defined automatically after completing proper definition of the BS. The Sector Association menu enables viewing the automatically defined sector association parameter. The sector is defined by the previously configured BS ID LSB. The Sector Association includes two association entries, for each of the relevant AU ports. The parameters for each association are:Sector Association AU Port Number: 1 and 2](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-159.png)
![Chapter 4 - Operation and Administration of the Micro BTS Sector Menu4Motion 707 System ManualSector Association Id: 1Radio Number: 1 and 2Radio Port Number: 1Antenna Number: 1 (Antenna Port Number: 1 and 2Note: Two vertical antennas are treated as one Antenna with 2 ports](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-160.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 708 System Manual4.7 BS MenuThe unit supports a single BS. The BS menu enables defining the BS, updating the BS parameters or deleting the BS (the BS ID LSB of an existing BS cannot be modified. To change the BS ID LSB, you must delete the BS and re-define it).The BS menu includes two options:“Add”“Select”4.7 .1 AddSelect the Add option to define the BS. Only a single BS can be defined. You will be prompted to configure the following BS mandatory parameters:4.7.1.1 BS ID LSBThe unique identifier of the BS in the network. A number in the range 1-16777215. The BS ID LSB used in the system is in the format A.B.C where A, B, C are from 0 to 255. The BS ID used in the Monitor program is an integer that is calculated by the formula A*65536+B*256+C. For example, a BS ID of 1.2.5 is translated to 1*65536+2*256+5=66053.4.7.1.2 Operator IDThe unique identifier of the wireless network operator. The same Operator ID must be used by all BSs in the managed wireless network. A number in the range 1-16777215 (same definition principle as for BS ID LSB). 4.7.1.3 Center FrequencyThe center of the frequency band in which the BS will transmit, in MHz. The valid values depend on the band supported by the device and the Bandwidth to be defined, are from f1+0.5BW to f2-0.5BW, where f1 is the lowest frequency of the radio band, f2 is the highest frequency of the band, and BW is the required bandwidth.4.7.1.4 BandwidthThe BS channel bandwidth (5 MHz, 7 MHz, 10MHz).A bandwidth of 7 MHz is not applicable for units in the 2.x GHz bands.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-161.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 709 System Manual4.7.1.5 Cell IDThe Cell ID (IDCell) used for preamble selection. The range is from 0 to 31. 4.7.1.6 Segment NumberThe segment (BS) number in a three sector BS (0-2). 4.7.1.7 Total Uplink DurationThe total duration of the uplink in a frame, in slots (one slot equals 3 symbols).To avoid BS-BS interference, the ul-dl-allocation must be identical in all BSs in a geographical region.The range is 4-7 or 10 for bandwidth of 5 or 10MHz, 3-5 or 7 for bandwidth of 7MHz. 4.7.1.8 Major GroupThe major groups allocated to the BS for maps transmission. Two hexadecimal digits in the range 00 to fc, representing 8 bits numbered 0 to 7 (left to right). Bits 0 to 5 indicate whether Subchannel Groups 0 to 5 (respectively) are allocated. Bits 6 and 7 are set to 0.If BW=5 MHz, bits 1, 3 and 5 are not relevant ("don't care"). bits 0, 2, and 4 should be set. Major Group must be set to A8.If BW=7/10 MHz with reuse 1, bits 0 to 5 must be set. The value must be set to fc.For BW=7/10 MHz with Reuse 3: If Segment Number = 0, then bits #0 and 1 should be set. The value must be set to c0.If Segment Number = 1, then bits #2 and 3 should be set. The value must be set to 30.If Segment Number = 2, then bits #4 and 5 should be set. The value must be set to 0c.4.7.1.9 Basic Map RepetitionThe basic repetition used in the transmission of the maps using QPSK 1/2. The available options are 1, 2, 4 and 6. (1 means no repetitions).](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-162.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 710 System Manual4.7.1.10 DL Permutation BaseThe permutation base used in the downlink data zone.The valid range is from 0 to 31.4.7.1.11 Permutation BaseThe permutation base used in the uplink feedback zone.The valid range is from 0 to 69.4.7.1.12 UL Permutation BaseThe permutation base used in the uplink data zone.The valid range is from 0 to 69. 4.7.1.13 IP AddressThe IP address of the bearer interface of the BS. Must be unique in the network. Must be in the same subnet with the unit’s bearer interface.4.7.1.14 IP Subnet MaskThe IP subnet mask of the bearer interface of the BS.4.7.1.15 Default GatewayThe IP address of the default gateway of the bearer interface of the BS. Must be in the same subnet with the BS bearer IP Address.4.7.1.16 Vlan IDThe VLAN ID of the bearer interface of the BS. The range is 11-100, 110-4094. The default is 11.4.7.1.17 Default Authenticator IP AddressThe IP address of the default authenticator ASN GW. 4.7.1.18 Paging Group IDThe Paging Group ID of the BS. The range is from 0 to 65535. 0 means that Idle Mode is not enabled. If Idle Mode is enabled (Paging Group ID is not 0), must be unique in the network (different Paging Group ID for each BS).](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-163.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 711 System Manual4.7 .2 Se lectSelect the BS to view or update its parameters or to delete it. BS is selected by its BS ID LSB.The selected BS menu includes the following options:“General”“Air Frame Structure Zones”“Mobility”“Power Control”“Feedback”“Air Frame Structure General”“Connectivity”“Management”“Keep Alive”“Scheduler”4.7.2.1 GeneralThe selected BS General parameters menu includes the following options:Show: Select to view the current values of the BS General parameters.Update: Select to update the configured values of the BS General parameters.Delete: Select to delete the BS (the BS ID LSB of an existing BS cannot be modified. To change it you must delete the BS and re-define it).The BS General parameters are:“Operator ID”“Name”](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-164.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 712 System Manual“Center Frequency”“Bandwidth”“Paging Group ID”4.7.2.1.1 Operator IDThe unique identifier of the wireless network operator. The same Operator ID must be used by all BSs in the managed wireless network. A number in the range 1-16777215. The Operator ID used in the system is in the format A.B.C where A, B, C are from 0 to 255. The Operator used in the Monitor program is an integer that is calculated by the formula A*65536+B*256+C. For example, an Operator ID of 1.1.1is translated to 1*65536+1*256+1=65793.4.7.2.1.2 NameThe name of the BS. An optional descriptive parameter. A string of up to 32 printable characters.4.7.2.1.3 Center FrequencyThe center of the frequency band in which the BS will transmit, in MHz. The valid values depend on the band supported by the device and the Bandwidth to be defined, are from f1+0.5BW to f2-0.5BW, where f1 is the lowest frequency of the radio band, f2 is the highest frequency of the band, and BW is the required bandwidth.4.7.2.1.4 BandwidthThe BS channel bandwidth (5 MHz, 7 MHz, 10MHz).A bandwidth of 7 MHz is not applicable for units in the 2.x GHz bands.4.7.2.1.5 Paging Group IDThe Paging Group ID of the BS. The single sector Idle Mode capability provides the benefits of MS power savings and manageable total sector active and non active users, together with reduced overhead on the backhaul network.Idle Mode (IM) mechanism allows an MS to become unavailable on the air interface, and thus freeing operational resources and preserving MS power. During IM operation, an MS switch off its transmission and reception capabilities, and becomes available for DL broadcast control messaging, i.e., MS Paging, in a periodically manner. Using paging broadcast, BS can indicate (if necessary) the MS to exit from IM and return into normal operation mode. The paging control message is sent over the DL of a set of BSs simultaneously. This set is called Paging group (PG). In the current release, each Paging Group includes a single BS.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-165.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 713 System ManualDuring IM, MS performs location updates when moving from one PG to another. While in the same PG, MS does not need to transmit in the UL and can be paged in the DL if there is traffic targeted at it.The range of the Paging Group ID parameter is from 0 to 65535. 0 means that Idle Mode is not enabled. If Idle Mode is enabled (Paging Group ID is not 0), must be unique in the network (different Paging Group ID for each BS).4.7.2.2 Air Frame Structure ZonesThe Air Frame Structure Zones menu includes the following options:“Uplink Data Zone”“Downlink Data Zone”“First Zone”“Uplink Feedback Zone”“Frame Structure Mode”4.7.2.2.1 Uplink Data ZoneThe Uplink Data Zone menu enables viewing/updating the values configured for the following parameters:“Uplink Basic Rate”“UL Permutation Base”4.7.2.2.1.1 Uplink Basic RateThe uplink basic rate:ctcQpskOneOverTwoTimesSix (QPSK 1/2 Repetition 6)ctcQpskOneOverTwoTimesFour (QPSK 1/2 Repetition 4)ctcQpskOneOverTwoTimesTwo (QPSK 1/2 Repetition 2)ctcQpskOneOverTwo (QPSK 1/2)ctcQpskThreeOverFour (QPSK 3/4)](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-166.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 714 System ManualctcQamSixteenOneOverTwo 16-QAM 1/2ctcQamSixteenThreeOverFour (16-QAM 3/4)ctcQamSixtyFourOneOverTwo (64-QAM 1/2)ctcQamSixtyFourTwoOverThree (64-QAM 2/3)ctcQamSixtyFourThreeOverFour (64-QAM 3/4)ctcQamSixtyFourFiveOverSix 64-QAM 5/6The default is ctcQpskOneOverTwo (QPSK 1/2).4.7.2.2.1.2 UL Permutation BaseThe permutation base used in the uplink data zone.The valid range is from 0 to 69. 4.7.2.2.2 Downlink Data ZoneThe Downlink Data Zone menu enables viewing/updating the values configured for the following parameters:“Basic Rate for Management”“Basic Rate for Data”“DL Permutation Base”4.7.2.2.2.1 Basic Rate for ManagementThe downlink basic rate for unicast and broadcast management:ctcQpskOneOverTwoTimesSix (QPSK 1/2 Repetition 6)ctcQpskOneOverTwoTimesFour (QPSK 1/2 Repetition 4)ctcQpskOneOverTwoTimesTwo (QPSK 1/2 Repetition 2)ctcQpskOneOverTwo (QPSK 1/2)ctcQpskThreeOverFour (QPSK 3/4)ctcQamSixteenOneOverTwo 16-QAM 1/2](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-167.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 715 System ManualctcQamSixteenThreeOverFour (16-QAM 3/4)ctcQamSixtyFourOneOverTwo (64-QAM 1/2)ctcQamSixtyFourTwoOverThree (64-QAM 2/3)ctcQamSixtyFourThreeOverFour (64-QAM 3/4)ctcQamSixtyFourFiveOverSix 64-QAM 5/6The default is ctcQpskOneOverTwo (QPSK 1/2).4.7.2.2.2.2 Basic Rate for DataThe downlink basic rate for data:ctcQpskOneOverTwoTimesSix (QPSK 1/2 Repetition 6)ctcQpskOneOverTwoTimesFour (QPSK 1/2 Repetition 4)ctcQpskOneOverTwoTimesTwo (QPSK 1/2 Repetition 2)ctcQpskOneOverTwo (QPSK 1/2)ctcQpskThreeOverFour (QPSK 3/4)ctcQamSixteenOneOverTwo 16-QAM 1/2ctcQamSixteenThreeOverFour (16-QAM 3/4)ctcQamSixtyFourOneOverTwo (64-QAM 1/2)ctcQamSixtyFourTwoOverThree (64-QAM 2/3)ctcQamSixtyFourThreeOverFour (64-QAM 3/4)ctcQamSixtyFourFiveOverSix 64-QAM 5/6The default is ctcQpskOneOverTwo (QPSK 1/2).4.7.2.2.2.3 DL Permutation BaseThe permutation base used in the downlink data zone.The valid range is from 0 to 31.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-168.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 716 System Manual4.7.2.2.3 First ZoneThe First Zone menu enables viewing/updating the values configured for the following parameters:“Major Group”“Basic Map Repetition”“Minimum Size”“Maximum Size”“Maximum Map Size”4.7.2.2.3.1 Major GroupThe major groups allocated to the BS for maps transmission. Two hexadecimal digits in the range 00 to fc, representing 8 bits numbered 0 to 7 (left to right). Bits 0 to 5 indicate whether Subchannel Groups 0 to 5 (respectively) are allocated. Bits 6 and 7 are set to 0.If BW=5 MHz, bits 1, 3 and 5 are not relevant ("don't care"). bits 0, 2, and 4 should be set. Major Group must be set to A8.If BW=7/10 MHz with reuse 1, bits 0 to 5 must be set. The value must be set to fc.For BW=7/10 MHz with Reuse 3: If Segment Number = 0, then bits #0 and 1 should be set. The value must be set to c0.If Segment Number = 1, then bits #2 and 3 should be set. The value must be set to 30.If Segment Number = 2, then bits #4 and 5 should be set. The value must be set to 0c.4.7.2.2.3.2 Basic Map RepetitionThe basic repetition used in the transmission of the maps using QPSK 1/2. The available options are 1, 2, 4 and 6. (1 means no repetitions).The default is 6 (rate QPSK 1/2 repetition 6)](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-169.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 717 System Manual4.7.2.2.3.3 Minimum SizeThe initial size (in symbols) of the first zone. When reuse 3 is used within first zone, this parameter should be equal across all BSs within deployment.The available options are 2, 4,....34 (2xN where N=1-17) or No Limitation. The default is No Limitation.See limitations in “First Zone Minimum Size Recommended Value Range” table below. Other values should be avoided.In the current release this is the actual first zone size. For reuse 1 the default (no limitation) can be used-the actual size will be set dynamically according to the configuration. For reuse 3 a specific value must be configured.4.7.2.2.3.4 Maximum SizeMaximum size (in symbols) for first zone. Used mainly for performance control capability within frame.The available options are 2, 4,....34 (2xN where N=1-17) or No Limitation. The default is No Limitation.Maximum Size cannot be lower than Minimum Size.In the current release this parameter is not applicable (first zone size is defined only by the Minimum Size parameter).](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-170.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 718 System ManualRecommended values for First Zone Minimum Size and Maximum Size:* First Zone Scheme is being determined by the selected Map Major Groups:For 7/10 MHz Full Loading means all Major Groups (0-5) are selected.For 5MHz Full Loading means that all relevant Major Groups (0, 2, 4) are selected.For First Zone Maximum Size the values are:If First Zone Minimum Size is set to No Limitations, the value range for Maximum Size is the same as for Minimum Size.Else, the value range is No Limitations or First Zone Minimum Size+2N, up to a maximum of Y as defined below.Table 4-2: First Zone Minimum Size Recommended Value RangeBandwidth (MHz)First Zone Scheme*Basic Map Repetition Minimum Size (symbols) (up to a maximum of Y as defined below)7/10 Full Loading 6 No Limitation or 8+2N4 No Limitation or 6+2N2 No Limitation or 4+2N1 No Limitation or 4+2NReuse 1/3 6 N/A (non trivial configuration)48+2N26+2N16+2N5 MHz Full Loading 6 N/A (non trivial configuration)4 No Limitation or 8+2N2 No Limitation or 6+2N1 No Limitation or 4+2NReuse 1/3 6 N/A (non trivial configuration)4 N/A (non trivial configuration)2 N/A (non trivial configuration)1 N/A (non trivial configuration)](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-171.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 719 System ManualThe value of Y that sets the upper limit for the Minimum and Maximum Size parameters depends on the Maximum Cell Radius and Total Uplink Duration parameters, using the following formula:Y=A-3*(Total Uplink Duration)-(Extra TTG), where A=46 for BW of 5 or 10 MHz, and 32 for BW of 7 MHz.4.7.2.2.3.5 Maximum Map SizeLimits the maximum size of maps (in slots). The available options are 10, 20 ...300 (10xN where N=1-30) or No Limitation. The default is No Limitation.4.7.2.2.4 Uplink Feedback ZoneThe Uplink Feedback Zone menu enables viewing/updating the values configured for the following parameter:4.7.2.2.4.1 Permutation BaseThe permutation base used in the uplink feedback zone.The valid range is from 0 to 69. 4.7.2.2.5 Frame Structure ModeThe Frame Structure Mode menu enables viewing/updating the values configured for the following parameter:4.7.2.2.5.1 RCID UsageEach transmitted MAP includes allocations for each MS it served, using the MS’s CID for identifying each MS. The original CID includes 16 bits, which is significantly more than practically needed since a maximum of 500 MSs can be served by each BS. To reduce overhead, a smaller number of bits can be used, based on RCID (Reduced CID) defined in the standard. This mechanism can be Table 4-3: Calculating the Upper Limit Value (Y) for Minimum and Maximum SizeBandwidth (MHz) Maximum Cell Radius Total Uplink Duration (slots) Extra TTG (symbols)5/10 1, 2, 4, 8 4, 6 01, 2, 4, 8, 15, 23 5, 7 115, 23, 30 4, 6 230 5, 7 37 1, 2, 4, 8, 15, 23 4 01, 2, 4, 8, 15, 23, 30 3, 5 130 4 2](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-172.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 720 System Manualused only if all MSs served by the BS support RCID. When enabled, CIDs of either 7 or 11 bits will be dynamically used, according to the current number of MS served at each given moment.The RCID Usage defines whether RCID is enabled or disabled. The default is Disable.4.7.2.3 MobilityThe Mobility menu enables viewing/updating the values configured for the following parameter:4.7.2.3.1 DeploymentThe type of deployment in the area served by the BS: Fix or Mobile. To support proper handover, should be set to Fix only if mobile MSs are not expected. The default is Fix.4.7.2.4 Power ControlThe Power Control menu enables viewing/updating the values configured for the following parameters:“Target Ni”“Required C/N Levels - ACK”“Required C/N Levels - CQI”“Required C/N Levels - CDMA”“Required C/N Levels - QPSK 1/2”“Required C/N Levels - QPSK 3/4”“Required C/N Levels -16-QAM 1/2”“Required C/N Levels - 16-QAM 3/4”“Required C/N Levels - 64-QAM 1/2”“Required C/N Levels - 64-QAM 2/3”“Required C/N Levels -64-QAM 3/4”](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-173.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 721 System Manual“Required C/N Levels - 64-QAM 5/6”“Allowed Interference Level”4.7.2.4.1 Target NiThe target noise and interference level for the PUSC zone, in dBm.The range is from -130 to -110 in steps of 1 (dBm). The default is -127.4.7.2.4.2 Required C/N Levels - ACKThe C/N in dB required for sending ACK, reported to the MS for power control purposes.The range is from -20 to 50 (dB). The default is 7.4.7.2.4.3 Required C/N Levels - CQIThe C/N in dB required for sending CQI, reported to the MS for power control purposes.The range is from -20 to 50 (dB).Must be in the range from Required C/N Levels - ACK - 8 to Required C/N Levels - ACK + 7. The default is 12.4.7.2.4.4 Required C/N Levels - CDMAThe C/N in dB required for transmitting CDMA, reported to the MS for power control purposes.The range is from -20 to 50 (dB).Must be in the range from Required C/N Levels - CQI - 8 to Required C/N Levels - CQI + 7. The default is 9.4.7.2.4.5 Required C/N Levels - QPSK 1/2The C/N in dB required for sending QPSK 1/2, reported to the MS for power control purposes.The range is from -20 to 50 (dB).Must be in the range from Required C/N Levels - CDMA - 16 to Required C/N Levels - CDMA + 14. The default is 13.4.7.2.4.6 Required C/N Levels - QPSK 3/4The C/N in dB required for sending QPSK 3/4, reported to the MS for power control purposes.The range is from -20 to 50 (dB).](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-174.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 722 System ManualMust be in the range from Required C/N Levels - QPSK 1/2 - 16 to Required C/N Levels - QPSK 1/2 + 14. The default is 16.4.7.2.4.7 Required C/N Levels -16-QAM 1/2The C/N in dB required for transmitting 16-QAM 1/2, reported to the MS for power control purposes.The range is from -20 to 50 (dB).Must be in the range from Required C/N Levels - QPSK 3/4 - 8 to Required C/N Levels - QPSK 3/4 + 7. The default is 19.4.7.2.4.8 Required C/N Levels - 16-QAM 3/4The C/N in dB required for sending 16-QAM 3/4, reported to the MS for power control purposes.The range is from -20 to 50 (dB).Must be in the range from Required C/N Levels - 16-QAM 1/2 - 16 to Required C/N Levels - 16-QAM 1/2 + 14. The default is 22.4.7.2.4.9 Required C/N Levels - 64-QAM 1/2The C/N in dB required for sending 64-QAM 1/2, reported to the MS for power control purposes.The range is from -20 to 50 (dB).Must be in the range from Required C/N Levels - 16-QAM 3/4 - 16 to Required C/N Levels - 16-QAM 3/4 + 14. The default is 23.4.7.2.4.10 Required C/N Levels - 64-QAM 2/3The C/N in dB required for sending 64-QAM 2/3, reported to the MS for power control purposes.The range is from -20 to 50 (dB).Must be in the range from Required C/N Levels - 64-QAM 1/2 - 8 to Required C/N Levels - 64-QAM 1/2 + 7. The default is 25.4.7.2.4.11 Required C/N Levels -64-QAM 3/4The C/N in dB required for sending 64-QAM 2/3, reported to the MS for power control purposes.The range is from -20 to 50 (dB).Must be in the range from Required C/N Levels - 64-QAM 2/3 - 8 to Required C/N Levels - 64-QAM 2/3 + 7. The default is 26.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-175.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 723 System Manual4.7.2.4.12 Required C/N Levels - 64-QAM 5/6The C/N in dB required for transmitting 64-QAM 5/6, reported to the MS for power control purposes.The range is from -20 to 50 (dB).Must be in the range from Required C/N Levels - 64-QAM 3/4 - 8 to Required C/N Levels - 64-QAM 3/4 + 7. The default is 28.4.7.2.4.13 Allowed Interference LevelThis parameter defines the correction of maximum allowed UL SINR based on measured DL SINR.The options are Very High, High, Medium, Low.The default is High.4.7.2.5 FeedbackThe Feedback menu enables viewing/updating the values configured for the following parameters:“IR CDMA Allocations Period”“Start of Ranging Codes Used”“Maximum Cell Radius”4.7.2.5.1 IR CDMA Allocations PeriodThe period of IR CDMA allocations, in frames.The available options are 1, 2, 4, 6, 8, 10. The default is 2.In the current release the actual value is always 2 (the configured value is ignored).4.7.2.5.2 Start of Ranging Codes UsedThe starting number of the group of codes used for the uplink.The available options are 0, 64, 128, 192. The default is 0.4.7.2.5.3 Maximum Cell RadiusThe maximum cell radius (in km).The available values are 1, 2, 4, 8, 15, 23. 30. The default is 2.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-176.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 724 System Manual4.7.2.6 Air Frame Structure GeneralThe Air Frame Structure General menu enables viewing/updating the values configured for the following parameters:“Cell ID”“Preamble Group”“Segment Number”“Preamble Index”“Total Uplink Duration”“Operational Status Channel 1”“Operational Status Channel 2”“Neighbor with Beamforming”4.7.2.6.1 Cell IDThe Cell ID (IDCell) used for preamble selection. The range is from 0 to 31. 4.7.2.6.2 Preamble GroupThe preamble group (1 or 2). A value of 2 is applicable only for the following combinations of Segment Number and Cell ID values:Segment Number=0, Cell ID=0, 3, 6, 9, 12, 15.Segment Number=1, Cell ID=1, 4, 7, 10, 13, 16.Segment Number=2, Cell ID=2, 5, 8, 11, 14, 17The default is 1.4.7.2.6.3 Segment NumberThe segment (BS) number in a three sector BS (0-2).4.7.2.6.4 Preamble IndexRead-only. The Preamble Index used by the BS (0-113).4.7.2.6.5 Total Uplink DurationThe total duration of the uplink in a frame, in slots (one slot equals 3 symbols).](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-177.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 725 System ManualTo avoid BS-BS interference, the ul-dl-allocation must be identical in all BSs in a geographical region.The range is 4-7 or 10 for bandwidth of 5 or 10MHz, 3-5 or 7 for bandwidth of 7MHz. 4.7.2.6.6 Operational Status Channel 1Read-only. The operational status of Channel 1.4.7.2.6.7 Operational Status Channel 2Read-only. The operational status of Channel 2.4.7.2.6.8 Neighbor with BeamformingThe beam forming mechanism that may be used by neighboring BSs is based on symmetry in performance between uplink and down link. To compensate for possible differences due to HW of the ODU, a special low-level calibration signal is transmitted periodically in each link. During the time this calibration signal is transmitted all other radio links of the same BS and all its neighbors should not transmit, to reduce potential interference. The Beam Forming mechanism ensures that all neighboring BSs operating in Beam Forming mode will enter into silent mode when necessary. A Micro BTS operating in Matrix A or B mode should enter into silent mode when necessary (based on frame number information) only if it has neighboring BSs operating in Beam Forming mode.The options are Yes and No. Set to Yes only if the unit has at least one neighbor BS operating in Beam Forming mode.The default is No.4.7.2.7 ConnectivityThe Connectivity menu includes the following options:“Bearer Interface”“Authentication”“QOS Marking Rules”“ASN-GW Load Balancing”4.7.2.7.1 Bearer InterfaceThe Bearer Interface menu enables viewing/updating the values configured for the following parameters:](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-178.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 726 System Manual“IP Address”“IP Subnet Mask”“Default Gateway”“Vlan ID”“Default Gateway Connectivity Status”4.7.2.7.1.1 IP AddressThe IP address of the bearer interface of the BS. Must be unique in the network. Should be in the same subnet, together with the unit’s bearer interface.4.7.2.7.1.2 IP Subnet MaskThe IP subnet mask of the bearer interface of the BS.4.7.2.7.1.3 Default GatewayThe IP address of the default gateway of the bearer interface of the BS. Must be in the same subnet with the BS bearer IP Address.4.7.2.7.1.4 Vlan IDThe VLAN ID of the bearer interface of the BS. The range is 11-100, 110-4094. 4.7.2.7.1.5 Default Gateway Connectivity StatusRead-only. The status of connectivity with the default authenticator: Unknown, Up, down. The keep-alive mechanism starts only after first registration at the ASN-GW. Until then this mechanism is disable and connectivity status is Unknown.4.7.2.7.2 AuthenticationThe Authentication menu enables viewing/updating the values configured for the following parameters:“Default Authenticator IP Address”“Thresholds - Suspended EAP Process”“Threshold - Active MSs”“Threshold - Maximum EAP Rounds”4.7.2.7.2.1 Default Authenticator IP AddressThe IP address of the default authenticator ASN GW.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-179.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 727 System Manual4.7.2.7.2.2 Thresholds - Suspended EAP ProcessSuspended EAP authentication process threshold. It is used to set an alarm.The range is 0-10000. The default is 10000.Note: The relevant alarm is not supported in current release.4.7.2.7.2.3 Threshold - Active MSsThe threshold for the number of MSs in active operation state (not Idle) served by the BS. Exceeding this threshold sets the alarm “Excessive MS number”. The range is 0-1024. When set to 0, the alarm is disabled. The default is 1024.4.7.2.7.2.4 Threshold - Maximum EAP RoundsThe threshold for the number of EAP rounds in one direction in the same EAP session. When this threshold is exceeded, alarm is set. This threshold may be used to protect the system from hazard EAP sessions with extreme number of messaging round trips. The range is 0-100. When set to 0, the alarm is disabled. The default is 100.Note: The relevant alarm is not supported in current release.4.7.2.7.3 QOS Marking RulesThe QoS Marking Rules menu includes the following options:“Internal ASN Traffic QOS Rules”“Internal Management Traffic QOS Rules”“QOS Rules”4.7.2.7.3.1 Internal ASN Traffic QOS RulesThe Internal ASN Traffic QOS Rules menu enables viewing/updating the values configured for the following parameters:“Diffserv Code Point”“802.1p Priority”4.7.2.7.3.1.1Diffserv Code PointDSCP priority value to be used for marking of intra-ASN (R8/R6) traffic. The range is 0-63. The default is 0.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-180.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 728 System Manual4.7.2.7.3.1.2802.1p Priority802.1p priority value to be used for marking of intra-ASN (R8/R6) traffic. The range is 0-7. The default is 0.4.7.2.7.3.2 Internal Management Traffic QOS RulesThe Internal Management Traffic QOS Rules menu enables viewing/updating the values configured for the following parameters:“Diffserv Code Point”“802.1p Priority”4.7.2.7.3.2.1Diffserv Code PointDSCP priority value to be used for marking of internal management traffic. The range is 0-63. The default is 0.4.7.2.7.3.2.2802.1p Priority802.1p priority value to be used for marking of internal management traffic. The range is 0-7. The default is 0.4.7.2.7.3.3 QOS RulesThe QOS Rules menu includes the following options:Show: Use the Show option to view the main parameters (Rule Status, Marking Rule Name, Service Flow Data Delivery Type, Service Flow Traffic Priority) of each of the existing QoS Rules.Add: Use the Add option to add a new QoS Rule.Select: Use the Select option to select a specific QoS Rule. You can than select one of the following:»Use the Show option to view all parameters of the selected rule.»Use the Update option to update one or several parameters of the selected rule.»Use the Delete option to remove the selected rule from the database. The QOS Rule parameters are:4.7.2.7.3.3.1Rule NumberThe index number of the rule. A number in the range 1-16383.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-181.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 729 System Manual4.7.2.7.3.3.2Rule StatusThe status of the rule (Enable or Disable).4.7.2.7.3.3.3Marking Rule NameThe name of the QoS Marking Rule. An optional s string of up to 32 characters.4.7.2.7.3.3.4Service Flow Data Delivery TypeThe Service Flow Type for data delivery services: ugs, rtvr, nrtvr, be, ertvr, or ANY.4.7.2.7.3.3.5Service Flow Traffic PriorityThe priority of Service Flow traffic. 0-7 or ANY (255).4.7.2.7.3.3.6Service Flow Media FlowTypeThe Service Flow Media Flow Type, as defined in ASN-GW or AAA server4.7.2.7.3.3.7Enable Service Flow Media Flow TypeIndicates whether the condition for Service Flow Media Flow Type is enabled or disabled. If true, the Service Flow Media Flow Type will be considered. when looking for a match.4.7.2.7.3.3.8Outer DSCP MarkingThe DSCP value to be used for marking the outer IP header (IP/GRE). The range is 0-63. 4.7.2.7.3.3.9802.1p Priority MarkingThe 802.1p priority to be used for marking traffic. The range is 0-7. 4.7.2.7.4 ASN-GW Load BalancingAt the BTS level, up to two pools (with different priorities), each with up to 10 ASN-GWs, can be defined (see “ASN-GW Load Balancing Pools” on page 695). The BS will “inherit” these pools. It should be noted the ASN-GW defined in the BS as the Default Authenticator will be automatically added to the Primary Pool that is the higher priority pool (although it will not be shown as belonging to the pool).At the BS level, you can enable/disable the use of each of the two pools. The Secondary Pool can be enabled only if the Primary Pool is enabled. Note that if both pools are disabled, or if the enabled pool(s) are empty, the ASN-GW load balancing feature is disabled and only the Default Authenticator will be used. The ASN-GW Load Balancing menu includes the following options:“Pools Availability”](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-182.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 730 System Manual“Primary Pool”“Secondary Pool”4.7.2.7.4.1 Pools AvailabilityThe Pools Availability option enables viewing/updating the status (Enabled/Disabled) of each of the pools. The Secondary Pool can be enabled only if the Primary Pool is enabled. 4.7.2.7.4.2 Primary PoolThe Primary Pool option enables viewing the IP Address and current Connectivity Status for each of the ASN-GWs in the pool, based on selection of the ASN-GW Index.4.7.2.7.4.3 Secondary PoolThe Secondary Pool option enables viewing the IP Address and current Connectivity Status for each of the ASN-GWs in the pool, based on selection of the ASN-GW Index.4.7.2.8 ManagementThe Management menu includes the following options:“Noise and Interference Level Thresholds”“DL Dropped Packets Ratio Thresholds”4.7.2.8.1 Noise and Interference Level ThresholdsThe Noise and Interference Level Thresholds menu enables viewing/updating the values configured for the following parameter:4.7.2.8.1.1 Uplink Median NoiseThe uplink median noise level represents the median value of the noise floor histogram. If the uplink median noise level exceeds this value, an excessive uplink median noise alarm will be generated.The value is in dBm/tone. The default value of -124 is set to 3 dB above the default value of the Target NI parameter.The range is from -135 to -100 (dBm)4.7.2.8.2 DL Dropped Packets Ratio ThresholdsThe DL Dropped Packets Ratio Thresholds menu enables viewing/updating the values configured for the following parameters:](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-183.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 731 System Manual“Best Effort”“RT-VR”“NRT-VR”“UGS”“ERT-VR”4.7.2.8.2.1 Best EffortThe threshold for excessive DL dropped packets ratio (in promils), of DL packets in all Best Effort services, which when exceeded triggers a Best Effort service alarm.The range is from 1 to 1000 (promil). The default is 1000.4.7.2.8.2.2 RT-VRThe threshold for excessive DL dropped packets ratio (in promils), of DL packets in all RT-VR services, which when exceeded triggers an RT-VR service alarm.The range is from 1 to 1000 (promil). The default is 1000.4.7.2.8.2.3 NRT-VRThe threshold for excessive DL dropped packets ratio (in promils), of DL packets in all NRT-VR services, which when exceeded triggers an NRT-VR service alarm.The range is from 1 to 1000 (promil). The default is 1000.4.7.2.8.2.4 UGSThe threshold for excessive DL dropped packets ratio (in promils), of DL packets in all UGS services, which when exceeded triggers a UGS service alarm.The range is from 1 to 1000 (promil). The default is 1000.4.7.2.8.2.5 ERT-VRThe threshold for excessive DL dropped packets ratio (in promils), of DL packets in all ERT-VR services, which when exceeded triggers an ERT-VR service alarm.The range is from 1 to 1000 (promil). The default is 1000.4.7.2.9 Keep AliveThe Keep Alive menu enables viewing/updating the values configured for the following parameters:“Enable Keep Alive”](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-184.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 732 System Manual“Keep Alive Period”“Polling Period”“Number of Retransmissions”4.7.2.9.1 Enable Keep AliveEnable/disable the keep-alive mechanism. The default is Disable.The following parameters are applicable only if Keep Alive is enabled.4.7.2.9.2 Keep Alive PeriodTime in milliseconds to wait for a response before initiating another polling attempt or reaching a decision that the polled entity has failed (if the maximum number of retries set by Number of Retransmissions has been reached).The range is from 100 to 10000 milliseconds (0.1 to 10 second). The default is 5000.4.7.2.9.3 Polling PeriodThe period in seconds between polling sessions.The range is from 10 to 1000 seconds. The default is 60 seconds.Polling Period x 1000 (value in milliseconds) cannot be lower than Keep Alive Period x (Number of Retransmissions+1)4.7.2.9.4 Number of RetransmissionsMaximum number of retries if Retransmission Timeout has expired without getting a response.The range is from 0 to 10. The default is 5.4.7.2.10 SchedulerScheduling uncommitted (above the maximum reserved rate) traffic can be done using one of the following options:Equal Time (ET) scheduling mode, in which air resources are being scheduled in a fair manner proportional to the users' excess traffic (maximum sustained rate - maximum reserved rate) SLAs.Equal Rate (ER) scheduling mode, in which air resources are allocated to users aiming at ensuring data rate fairness between users proportional to their excess traffic SLAs.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-185.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 733 System ManualAssuming a sector with diversity (different channels conditions) of active users, ET scheme enables higher aggregate sector throughput at the expense of data-rate fairness among users, while ER scheduling scheme ensures maximum data-rate fairness among users at the expense of lower aggregate sector throughput.Using ER scheduling scheme exposes the system to excessive allocation of air resources to highly active users having relatively poorer channel conditions. To ensure data-rate fairness, more resources will to be allocated to these users compared to users with relatively good channel conditions. The effect of a small number of such users within the sector will be reflected by reduced aggregate sector throughput as well as degradation of achievable rates for all users. To protect against “abusing” users, an instantaneous rate threshold can be defined within the scheduling scheme in which the amount of air resources for users with continuous instantaneous rate below the threshold is being limited. The more the abusing users' instantaneous rate is below the threshold, the more resource allocations limitation is applied. Three levels of dynamic protection are available:No protection. Low protection level - Protection against users with very poor channel conditions. Should be used where the abusing users instantaneous rates are far below the average instantaneous rate within the sector.Medium protection - Protection against users with relatively poor or very poor channel conditions. Should be used where the abusing users instantaneous rates are below or far below the average instantaneous rate within sector.A dynamic protection mechanism is implemented, in which the mechanism of limiting resource allocations is automatically and dynamically activated when needed.The Scheduler menu enables viewing/updating the values configured for the following parameters:“Scheduler Mode”“Scheduler DL Abuse Protection Level”“Scheduler UL Abuse Protection Level”](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-186.png)
![Chapter 4 - Operation and Administration of the Micro BTS BS Menu4Motion 734 System Manual4.7.2.10.1 Scheduler ModeThe basis for allocating excess bandwidth among relevant users:Equal Rate: Throughput FairnessEqual Time: Resource FairnessThe selected mode is applicable for both uplink and downlink schedulers.The default is Equal Rate.4.7.2.10.2 Scheduler DL Abuse Protection LevelApplicable only if the selected Scheduler Mode is Equal Rate. None: No ProtectionLow: Limit the DL resources allocated to MSs with very low DL transmission Rate.Medium: Limit the DL resources allocated to MSs with low and very low DL transmission Rate. The default is None.4.7.2.10.3 Scheduler UL Abuse Protection LevelApplicable only if the selected Scheduler Mode is Equal Rate. None: No ProtectionLow: Limit the UL resources allocated to MSs with very low UL transmission Rate.Medium: Limit the UL resources allocated to MSs with low and very low UL transmission Rate. The default is None.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-187.png)
![Chapter 4 - Operation and Administration of the Micro BTS Equipment Menu4Motion 735 System Manual4.8 Equipment Me nuThe Equipment menu includes the following options:“AU”“Radio”“Antenna”4.8 .1 AUThe AU menu includes the following options:“General”“Control”4.8.1.1 GeneralThe AU General menu enables viewing the general AU properties and status and updating the Required AU Type.4.8.1.1.1 Required AU TypeRead-only according to the HW of the unit. In the current release the only supported AU Type is auMicroOdu2x2 (5).4.8.1.1.2 AU InstalledRead-only. An indication of AU existence.4.8.1.1.3 Installed AU TypeRead-only. The detected AU Type.4.8.1.1.4 HW VersionRead-only. The HW Version of the AU card.4.8.1.1.5 HW RevisionRead-only. The HW Revision of the AU card.4.8.1.1.6 Serial NumberRead-only. The Serial Number of the AU card.4.8.1.1.7 Boot SW VersionRead-only. The Boot SW Version of the AU card.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-188.png)
![Chapter 4 - Operation and Administration of the Micro BTS Equipment Menu4Motion 736 System Manual4.8.1.1.8 HealthRead-only. The health status of the AU card.4.8.1.1.9 AU MAC AddressRead-only. The primary MAC address of the AU card.4.8.1.1.10 AU MAC Address SecondaryRead-only. The secondary MAC address of the AU card.4.8.1.2 ControlThe AU Control menu includes the following parameter:4.8.1.2.1 Shutdown Power Port 1This parameter can be used to shutdown power to port 1 of the radio. The default status is normal operation (no shutdown).4.8.1.2.2 Shutdown Power Port 2This parameter can be used to shutdown power to port 2 of the radio. The default status is normal operation (no shutdown).4.8.1.2.3 Last Reset ReasonRead-only. The reason for the last reset of the AU. Possible reasons include Unknown, Health Monitoring Failed, User Initiated. Configuration Failure, Internal Errors.4.8 .2 Ra dioThe Radio menu includes the following options for each of the two radios (1 and 2):“General”“Port”4.8.2.1 GeneralThe Radio General menu enables viewing the general radio properties and status and viewing/updating some general parameters.4.8.2.1.1 Required Radio TypeThe required radio type is set automatically to the value of the actual (installed) radio type. Radio Type is in the format oDUAAAABBBBZZZWPPRbyTCOu, where:](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-189.png)
![Chapter 4 - Operation and Administration of the Micro BTS Equipment Menu4Motion 737 System ManualAAAA = Lower bound of frequency band in MHz, rounded up to the nearest integer. BBBB = Upper bound of frequency band in MHz, rounded down. ZZZ = always 000 in TDD systems.W = always N in TDD systems. PP = maximum transmit power in dBm, rounded down. R = number of receive channels. T = number of transmit channels. C = Y if cavity filter or a gap in the band is present, N if not. O = Reserved (0).u = Indication of a Micro BTS Radio4.8.2.1.2 Required Frequency BandRead-only. The frequency band according to the properties defined by the required radio type.4.8.2.1.3 Required Maximum TX PowerRead-only. The maximum Tx power according to the properties defined by the required radio type.4.8.2.1.4 Required Port ConfigurationRead-only. The port configuration according to the properties defined by the required radio type.4.8.2.1.5 Installed Radio TypeRead-only. The actually installed radio type. Available only after completing proper creation of the BS (including a Center Frequency in the correct range) and configuring a proper value for the Port’s Tx Power parameter. The Serial Number and the values of the Port’s read-only parameters are available only after detecting the Installed Radio Type.4.8.2.1.6 Installed Frequency BandRead-only. The frequency band according to the properties defined by the installed radio type.4.8.2.1.7 Required Maximum TX PowerRead-only. The maximum Tx power according to the properties defined by the installed radio type.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-190.png)
![Chapter 4 - Operation and Administration of the Micro BTS Equipment Menu4Motion 738 System Manual4.8.2.1.8 Required Port ConfigurationRead-only. The port configuration according to the properties defined by the installed radio type.4.8.2.1.9 Serial NumberRead-only. The serial number of the radio card.4.8.2.2 PortThe Radio Port menu enables viewing the general radio port properties and status and viewing/updating some general parameters.4.8.2.2.1 TX PowerThe required Tx power at the radio port, in dBm.The actually available range depends on Radio Type: The upper limit, which is the default, is set by the Maximum Tx Power supported by the radio. The control range is 10 dBm.4.8.2.2.2 HW RevisionRead-only. The HW revision of the radio port card.4.8.2.2.3 HPA CardRead-only. An indication whether an HPA (High Power Amplifier) card in installed.4.8.2.2.4 HPA HW VersionRead-only. Applicable only if HPA card is installed. The HW version of the HPA card.4.8.2.2.5 Serial NumberRead-only. The serial number of the radio port card.4.8.2.2.6 RSSIRead-only. Average uplink RSSI in dBm of all bursts of all connected MSs.4.8 .3 AntennaTypically a 2-ports dual slant antenna is used. In cases where 2 separate antennas are used, the Antenna parameters are applicable for both antennas. The Antenna menu enables viewing/updating the following parameters:4.8.3.1 Antenna TypeAn optional descriptive text. Up to 254 characters.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-191.png)
![Chapter 4 - Operation and Administration of the Micro BTS Equipment Menu4Motion 739 System Manual4.8.3.2 Mechanical Down TiltThe downwards mechanical tilt of the antenna (in degrees) as opposed to the electrical tilt already integrated in the antenna (and thus taken as reference; instead of the horizontal plane). The range is from -90.0 to 90.0 using 0.1 degree resolution. Used only for information (inventory) purposes. The default is 0.4.8.3.3 Electrical Down TiltThe downwards electrical tilt of the antenna, in degrees. The range is from -90.0 to 90.0 using 0.1 degree resolution. Used only for information (inventory) purposes. The default is 0.4.8.3.4 LongitudeThe longitude of the antenna. The format is lll.mmm,a: lll.is longitude in degrees (between 000 to 179); mmm is in minutes (between 000 and 999); a - is E (east) or W (west) Used only for information (inventory) purposes. The default is 000.000,E.4.8.3.5 LatitudeThe latitude of the antenna. The format is ll.mmm,a: ll.is longitude in degrees (between 00 to 89); mmm is in minutes (between 000 and 999); a - is S (south) or N (north). Used only for information (inventory) purposes. The default is 00.000,N.4.8.3.6 Tower HeightThe height of the antenna above the ground in meters. The range is from 0 to 500. Used only for information (inventory) purposes. The default is 0.4.8.3.7 HeadingThe the azimuth angle (in degrees) between the center of the horizontal antenna beamwidth and the true north; counting clockwise.The range is from 0 to 359. Used only for information (inventory) purposes. The default is 0.4.8.3.8 Cable LossThe attenuation (in dB) of the cable between the ODU port and antenna port. The range is from 0 to 20 in 0.1 dB steps. Used only for information (inventory) purposes. The default is 0.5.4.8.3.9 Antenna Product TypeThe antenna type. The available options includes a list of default and standard antennas. The default is default1portV.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-192.png)
![Chapter 4 - Operation and Administration of the Micro BTS GPS Menu4Motion 740 System Manual4.9 GPS MenuThe GPS menu includes the following options:“General Configuration”“Inventory & Statuses”4.9 .1 General ConfigurationThe GPS General Configuration menu enables viewing/updating the following parameters:4.9.1.1 GPS TypeThe type of time synchronization source to be used. The currently available options are None and Trimble Lassen.The default is None,4.9.1.2 LongitudeThe longitude of the site. The format is lll.mmm,a: lll.is longitude in degrees (between 000 to 179); mmm is in minutes (between 000 and 999); a - is E (east) or W (west). The default is 000.000,E.Configurable only if GPS Type set to None. Otherwise they are read-only, displaying the value calculated by the GPS receiver.4.9.1.3 LatitudeThe latitude of the site. The format is ll.mmm,a: ll.is latitude in degrees (between 00 to 89); mmm is in minutes (between 000 and 999); a - is N (north) or S (south). The default is 00.000,N.Configurable only if GPS Type set to None. Otherwise they are read-only, displaying the value calculated by the GPS receiver.4.9.1.4 AltitudeThe altitude in meters of the site in meters, from -300.0 to 9000.0. The default is 0.Configurable only if GPS Type set to None. Otherwise they are read-only, displaying the value calculated by the GPS receiver.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-193.png)
![Chapter 4 - Operation and Administration of the Micro BTS GPS Menu4Motion 741 System Manual4.9.1.5 UTC Time and DateThe UTC (Coordinated Universal Time) date and time. Configurable only if the GPS Type is set to None. Otherwise it is the read-only data received from the GPS receiver.The format is hh: mm: ss, dd/mm/yyyyhh between 0 and 23, mm between 0 and 59, ss between 0 and 59, dd/mm with usual date and month rules, yyyy between 2006 to 9999.4.9.1.6 Hold Over Passed TimeoutApplicable only if a GPS receiver is used. Defines the period, in minutes, for which the device provides holdover when the GPS loses synchronization with its satellites. The range is from 0 to 2880 minutes. The default is 480 minutes.4.9.1.7 Stop TX After Hold Over TimeoutApplicable only if a GPS receiver is used. Indicates whether the BTS should stop data transmission if the GPS lost synchronization with its satellites and the holdover passed timeout has occurred (Enable/Disable). When enabled, the BTS will stop transmitting after being in holdover state for more than Holdover Passed Timeout. The default is Enable.4.9.1.8 Time Zone Offset From UTCThe offset of the local time from the UTC.The range is -12:00 to +13:00 in 30 minutes resolution. The default is +00.00.4.9.1.9 Local Time and DateA read-only display of the local date and time (using 24-hour clock) as calculated using the UTC Time and Date and taking into account the Time Zone Offset From UTC and Daylight Saving Time parameters. The format is: hh:mm:ss; dd/mm/yyyy. 4.9.1.10 Daylight Saving ModeThe Daylight Saving Mode parameter is used to enable or disable the daylight saving feature using the following Start Date, Stop Date and Advance Hour Factor parameters. The default is Disable.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-194.png)
![Chapter 4 - Operation and Administration of the Micro BTS GPS Menu4Motion 742 System Manual4.9.1.11 Advance Hour FactorWhen Daylight Saving is enabled, this parameter defines the amount of time by which the clock should be advanced during the daylight saving period.The available values are 0 (daylight saving disabled), 1 and 2 (hours). The default is 0.4.9.1.12 Start DateWhen Daylight Saving is enabled, this parameter defines the date for starting the daylight saving feature. At the beginning of this date (midnight at the beginning of this date), the clock will be advanced by the amount of hours specified by the Advance Hour Factor.Use the format dd.mm to define the date and month at which to start activating the Daylight Saving feature.4.9.1.13 Stop DateWhen Daylight Saving is enabled, this parameter defines the date for ending the daylight saving feature (at “Advance Hour Factor” hours after midnight at the end of this date).Use the format dd.mm to define the date and month at which to end activating the Daylight Saving feature.4.9 .2 Inventory & Stat use sThe Inventory & Statuses menu enables viewing the following read-only properties and status parameters:4.9.2.1 Navigation Processor SW VersionThe software version of the navigation processor of the GPS receiver (if used).4.9.2.2 Signal Processor SW VersionThe software version of the signal processor of the GPS receiver (if used).4.9.2.3 Number of SatellitesThe number of satellites currently acquired by the GPS.4.9.2.4 1PPS FailureThe status of External 1PPS clock (OK or Failed).](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-195.png)
![Chapter 4 - Operation and Administration of the Micro BTS GPS Menu4Motion 743 System Manual4.9.2.5 4 Satellites and moreNot applicable if a GPS receiver is not connected. Indicating whether 4 (the minimum required for initial synchronization) or more satellites are received by the GPS receiver (OK or Failed).4.9.2.6 2 Satellites and moreNot applicable if a GPS receiver is not connected. Indicating whether 2 (the minimum number required for maintaining synchronization) or more satellites are received by the GPS receiver (OK or Failed).4.9.2.7 GPS Communication FailureNot applicable if a GPS receiver is not connected. Indicating the status of communication with the GPS receiver (OK or Failed).4.9.2.8 Hold Over EnteredIndicating whether the device has entered into Hold Over state (None or Started).4.9.2.9 Hold Over timeout passedIndicating whether Hold Over Timeout has passed (None or Passed).4.9.2.10 BS Stopped to TransmitIndicating whether the BS is transmitting or not (OK/Stopped)](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-196.png)
![AAppendixSector Connections Schemes](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-197.png)
![Appendix A - Sector Connections Schemes4Motion 745 System ManualIn this Appendix:“Introduction” on page 746“Fourth Order Diversity, Beam Forming and MIMO” on page 747“Fourth Order Diversity, MIMO” on page 748“Second Order Diversity” on page 750](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-198.png)
![Appendix A - Sector Connections Schemes Introduction4Motion 746 System ManualA.1 I ntroductionThe 4Motion 4-Channels Access Units implement four transmit/receive channels and are capable of supporting Beam Forming and/or MIMO Matrix A/B technologies. The operation mode is selected via software, giving the maximal flexibility to select the appropriate mode for each scenario and for each user.The 2-Channels Access Units can support only MIMO Matrix A/B technology.The following sections explain the configurations that support the different available diversity scenarios.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-199.png)
![Appendix A - Sector Connections Schemes Fourth Order Diversity, Beam Forming and MIMO4Motion 747 System ManualA.2 Fourth Order Diversity, Beam Forming and MIMOThis section describes the configurations that enable support of both Beam Forming and MIMO technologies.Only ODUs that support Beam Forming should be used.The example is for two 4x2 ODUs, where only the Tx/Rx ports are used. 2x2 ODUs can be used instead, as well as a combinations of one 4x2 ODU and one 2x2 ODU in the same sector (provided that the two ODUs use the same frequency band).In the current release a Double Dual Slant (DDP) antenna should be used to support Beam Forming.Figure A-1: Beam Forming and MIMO Support with 1 Dual Dual Slant (4-elements) Antenna](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-200.png)
![Appendix A - Sector Connections Schemes Fourth Order Diversity, MIMO4Motion 748 System ManualA.3 Fourth Orde r Diversity, MI MOThis section describes the configurations that enable support of MIMO technologies with fourth order diversity.A.3.1 Wide Double Dual slant ArrayTwo separated Dual Slant antennas provide also space diversity.Figure A-2: Two Widely Spaced Dual Slant (2-elements) Antenna](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-201.png)
![Appendix A - Sector Connections Schemes Fourth Order Diversity, MIMO4Motion 749 System ManualA.3.2 Narrow Dual Dual Slant ArrayFigure A-3: One Dual Dual Slant (4-elements) Antenna](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-202.png)
![Appendix A - Sector Connections Schemes Second Order Diversity4Motion 750 System ManualA.4 Sec ond Order DiversityAll following configuration are shown with one 2x2 ODU. Two 1x1 ODUs can be used instead of the 2x2 ODU, provided both ODUs support the same frequency band.A.4.1 Wide Double Single Slant Array (Space a nd Pola rization Diversity)This configuration consists of two dual-slant antennas separated by at least 10 wavelengths, where only one antenna element of each is connected, with different polarization.Figure A-4: Wide Double Single Slant Array with Two Partially Used Dual Slant (2-elements) Antennas](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-203.png)
![Appendix A - Sector Connections Schemes Second Order Diversity4Motion 751 System ManualA.4.2 Narrow Dual Slant Array (Polarizat ion Dive rsity)Figure A-5: Narrow Dual Slant Array with One Dual Slant (2-elements) Antenna](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-204.png)
![Appendix A - Sector Connections Schemes Second Order Diversity4Motion 752 System ManualA.4.3 Wide Array, Vertica l Polarizat ion Ante nna s (Spac e Diversity)Figure A-6: Narrow Array with Two Vertical Polarization Antennas](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-205.png)
![Glossa ry](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-206.png)
![Glossary4Motion 911 System Manual10Base-T An Ethernet cabling standard where data is transmitted in baseband spectrum of a twisted pair cable (i.e. Cat 3 or better, Cat 5 in most networks) with data rate of 10 Mbps. (10 for 10Mbps, Base for baseband, T for twisted pair). 10Base-T implementation uses star topology. 100Base-T An Ethernet cabling standard where data is transmitted in baseband spectrum of a twisted pair cable (i.e. Cat 5 or better), with data rate of 100 Mbps. 100Base-T implementation uses star topology. 100Base-T is also known as Fast Ethernet. 1000Base-T An Ethernet cabling standard where data is transmitted in baseband spectrum of a twisted pair cable (Cat 5E or better), with data rate of 1000 Mbps. 1000Base-T implementation uses star topology. 1000Base-T is also known as Gigabit Ethernet.3G Third generation wireless service, designed to provide high data speeds, always-on data access, and greater voice capacity.AAA Authentication, Authorization, and Accounting (pronounced "triple a."). A system (or several systems) that controls what resources users have access to, and keeps track of the activity of users over the network. AAS Adaptive Antenna System, also called Advanced Antenna System, is a technology to enable the network operators to increase the wireless network capacity. In addition, adaptive antenna systems offer the potential of increased spectrum efficiency, extended range of coverage and higher rate of frequency reuse. Adaptive antenna systems consist of multiple antenna elements at the transmitting and/or receiving side of the communication link, whose signals are processed adaptively in order to exploit the spatial dimension of the mobile radio channel. Depending on whether the processing is performed at the transmitter, receiver, or both ends of the communication link, the adaptive antenna technique is defined as multiple-input single-output (MISO), single-input multiple-output (SIMO), or multiple-input multiple-output (MIMO).ACL Access Control List. A filtering mechanism used by many access IP routers that controls which traffic may be received or transmitted on an interface or port. AISG Antenna Interface Standards Group. The objective of the group is to facilitate the introduction of base station antennas with remotely adjustable tilt by agreeing open standards for the associated data transmission system.ANSI American National Standards Institute. A voluntary organization composed of corporate, government, and other members that coordinates standards-related activities, approves U.S. national standards, and develops positions for the United States in international standards organizations. ARP Address Resolution Protocol. Internet protocol used to map an IP address to a MAC address. Defined in RFC 826.ARQ Automatic Repeat reQuest. A communication technique in which the receiving device detects errors and requests retransmissions.ASCII American Standard Code for Information Interchange. A code for representing English characters as numbers, with each letter assigned a number from 0 to 127.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-207.png)
![Glossary4Motion 912 System ManualASN Access Service Network. An ASN is defined as a complete set of network functions needed to provide radio access to a WiMAX subscriber. An ASN is comprised of network elements such as one or more Base Stations (BS) and one or more ASN gateways (ASN-GW). An ASN may be shared by more than one Connectivity Service Network (CSN).ASN-GW Access Service Network Gateway. The ASN-GW is a network entity that acts as a gateway between the ASN and CSN. The ASN functions hosted in an ASN-GW may be viewed as consisting of two groups - the decision point (DP) that provides control functionality and enforcement point (EP) that provides bearer transport.ASP Application Service Provider. A third-party entity that manages and distributes software-based services and solutions to customers across a wide area network from a central data center.AU Access UnitAVU Air Ventilation UnitAWG An electronics industry acronym for American Wire Gauge. AWG is a measure of the thickness of copper, aluminum and other wiring.AWGN Additive White Gaussian Noise. Also known as WGN. Constant spectral energy at all frequencies with a probability histogram that follows a Gaussian bell shaped curve. BE Best Effort. Service supporting applications with no strict rate or delay requirements.BS Base Station. The WiMAX BS is an entity that implements the WiMAX MAC and PHY in compliance with the IEEE 802.16e standard. A BS operates on one frequency assignment, and incorporates scheduler functions for uplink and downlink resources.BTS Base Transceiver Station. A wireless network element that provides the radio interface of the network. The BTS comprises the radio transmission and reception devices, and also manages the signal processing related to the air interface.BW BandwidthBWA Broadband Wireless AccessCALEA The Communications Assistance for Law Enforcement Act is a United States wiretapping law passed in 1994. In its own words, the purpose of CALEA is: To amend title 18, United States Code, to make clear a telecommunications carrier's duty to cooperate in the interception of communications for Law Enforcement purposes, and for other purposes. CALEA was intended to preserve the ability of law enforcement agencies to conduct electronic surveillance by requiring that telecommunications carriers and manufacturers of telecommunications equipment modify and design their equipment, facilities, and services to ensure that they have the necessary surveillance capabilities.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-208.png)
![Glossary4Motion 913 System ManualCDMA Code Division Multiple Access is a second generation (2G) cellular technology defined by Qualcomm in IS-95 and IS-2000. A coding scheme, used as a modulation technique, in which multiple channels are independently coded for transmission over a single wideband channel. In some communication systems, CDMA is used as an access method that permits carriers from different stations to use the same transmission equipment by using a wider bandwidth than the individual carriers. On reception, each carrier can be distinguished from the others by means of a specific modulation code, thereby allowing for the reception of signals that were originally overlapping in frequency and time. Thus, several transmissions can occur simultaneously within the same bandwidth, with the mutual interference reduced by the degree of orthogonality of the unique codes used in each transmission. CE The CE-marking is a European Union regulatory community sign. It symbolizes the compliance of the product with all essential requirements relating to safety, public health, consumer protection.CINR Carrier-to-Interference plus Noise Ratio (expressed in dB)CIR Committed Information Rate. The rate (in bits per second) at which a network guarantees to transfer information under normal conditions, averaged over a minimum increment of time.CLI Command Line Interface. A user interface that accepts typed commands to instruct the managed device on the task to perform.cPCI Compact Peripheral Component Interface. a standard for computer backplane architecture and peripheral integration, defined and developed by the peripheral component interconnect (PCI) industrial computers manufacturers group (PICMG). Designed to provide rugged, high-density systems.CPU Central Processing Unit.CQI Channel Quality InformationCS Convergence Sublayer. Particular protocols that are responsible for gathering and formatting higher layer information so it can be processed by the lower layers.CSMA/CD Carrier Sense Multiple Access with Collision Detection. Media-access mechanisms wherein devices ready to transmit data first check the channel for a carrier. If no carrier is sensed for a specific period of time, a device can transmit. If two devices transmit at once, a collision occurs and is detected by all colliding devices. This collision subsequently delays retransmissions from those devices for some random length of time. Ethernet and IEEE 802.3 use CSMA/CD access.CSN Connectivity Service Network. A CSN is defined as a set of network functions that provide IP connectivity services to WiMAX subscribers and all the IP core network functions. A CSN is comprised of network elements such as routers, proxy/servers, user databases, and inter-working gateway devices.CTC Convolutional Turbo Code is a type of turbo codes with some of the convolutional schemes used. For its high-performance error correction nature, CTC is the iterative decoding scheme of choice as evidenced by their wide adoption in standards bodies.DCD Downlink Channel Descriptor.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-209.png)
![Glossary4Motion 914 System ManualDHCP Dynamic Host Configuration Protocol. A protocol for dynamically assigning IP addresses from a pre-defined list to nodes on a network. Using DHCP to manage IP addresses simplifies client configuration and efficiently utilizes IP addresses. DL Down LinkDSCP Differentiated Service Code Point, AKA DiffServ: An alternate use for the ToS byte in IP packets. Six bits of this byte are being reallocated for use as the DSCP field where each DSCP specifies a particular per-hop behavior that is applied to the packet.DNS Domain Naming System. A system that stores information about hostnames and domain names. DNS provides an IP address for each hostname, and lists the e-mail exchange servers accepting e-mail addresses for each domain. DoS Denial of ServiceDSL Digital Subscriber Line. A technology that exploits unused frequencies on copper telephone lines to transmit traffic typically at multi-megabit speeds. DSL can allow voice and high-speed data to be sent simultaneously over the same line. Because the service is 'always available,' end-users don't need to dial in or wait for call set-up.EAP Extensible Authentication Protocol, A protocol used between a user station and an authenticator or authentication server. It acts as a transport for authentication methods or types. It, in turn may be encapsulated in other protocols, such as 802.1x and RADIUS. EAP is defined by RFC 2284.EDT Electrical Down-TiltEIRP Equivalent Isotropic Radiated Power. The apparent power transmitted towards the receiver, if it is assumed that the signal is radiated equally in all directions. The EIRP is equal to the power (in dBm) at the antenna port, plus the power gained from the directivity of the antenna (in dBi).EMC Electro-Magnetic Compatibility. The capability of equipment or systems to be used in their intended environment within designed efficiency levels without causing or receiving degradation due to unintentional EMI (Electro Magnetic Interference). EMC generally encompasses all of the electromagnetic disciplines. EMS Element Management System. An element management system (EMS) manages one or more of a specific type of telecommunications network element (NE). Typically, the EMS manages the functions and capabilities within each NE but does not manage the traffic between different NEs in the network.EN Abbreviation for "European Norm".ERT-VR Extended Real-Time Variable Rate. Service supporting real-time applications with variable bit rates that require guaranteed data rate, delay and low jitter, such as voice.ETS European Telecommunications Standard](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-210.png)
![Glossary4Motion 915 System ManualETSI European Telecommunications Standards Institute. A non-profit organization producing voluntary telecommunications standards used throughout Europe, some of which have been adopted by the EC as the technical base for Directives or Regulations. FA Foreign Agent. A mobility agent on the foreign network that can assist the mobile node in receiving datagrams delivered to the care-of address. (The foreign network is the network to which the mobile node is attached when it is not attached to its home network, and on which the care-of-address is reachable from the rest of the Internet). See also HA (Home Agent).FCC Federal Communications Commission. A U.S. government agency that supervises, licenses, and controls electronic and electromagnetic transmission standards. FEC Forward Error Correction. A method of communicating data that can corrects errors in transmission on the receiving end. Prior to transmission, the data is put through a predetermined algorithm that adds extra bits specifically for error correction to any character or code block. If the transmission is received in error, the correction bits are used to check and repair the data.FFT Fast Fourier Transform. An algorithm for converting data from the time domain to the frequency domain; often used in signal processing.FTP File Transfer Protocol. A protocol for exchanging files over the Internet. FTP uses the Internet's TCP/IP protocols to enable data transfer.GMT Greenwich Mean Time. On January 1, 1972, GMT was replaced as the international time reference by Coordinated Universal Time (UTC), maintained by an ensemble of atomic clocks around the world.GPS Global Positioning System. A system that uses satellites, receivers and software to allow users to determine their precise geographic position.GRE General Routing Encapsulation. A method or technique of adding an IP standard header and trailer to a message that does not follow IP protocols. The encapsulated message is sent over a public network while received messages are stripped of the wrapper and processed. This permits non-standard data and totally encrypted messages to use the Internet. The technology is an important element in Virtual Private Network (VPN) offerings.HA Home Agent. A node on the home network (the network at which the mobile node seems reachable, to the rest of the Internet, by virtue of its assigned IP address) that effectively causes the mobile node to be reachable at its home address even when the mobile node is not attached to its home network. HARQ Hybrid Automatic Repeat reQuest (Hybrid ARQ) is a scheme wherein information blocks are encoded for partial error correction at receiver and additional, uncorrected errors are retransmitted.HO Hand-Over.HP Abbreviation for "Horizontal Pitch" or standard width measurement which defines the width for plug-in modules in the 19” construction system. One HP equals 5.08 mm.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-211.png)
![Glossary4Motion 916 System ManualIANA Internet Assigned Numbers Authority. A regulatory group that maintains all assigned and registered Internet numbers, such as IP and multicast addresses.ICMP Internet Control Message Protocol is a protocol designed to allow hosts to send error and control messages to other network devices. Basically ICMP provides communication between the Internet Protocol (IP) software on network devices. The short ICMP messages use IP packets and are usually processed by the IP software, rather than presented to the user at the application level.IEC The International Electro-Technical Commission. an international organization that writes standards for safety for electrical and other equipment. Many IEC standards were adopted from the German VDE, which was the main historical standards-writing body in Europe. One goal of the IEC is to harmonize differing standards between European countries to facilitate free trade. The U.S. Underwriters Laboratories (UL) and the Canadian CSA are members of the IEC.IEEE Institute of Electrical and Electronics Engineers. IEEE (pronounced I-triple-E) is an organization composed of engineers, scientists, and students. The IEEE is best known for developing standards for the computer and electronics industry. In particular, the IEEE 802 standards for local-area networks are widely followed.IEEE 802.16 Also known as WIMAX. A group of broadband wireless communications standards for metropolitan area networks (MANs) developed by a working group of the IEEE.IEEE 802.16e 802.16e, also known as 802.16-2005, is an IEEE standard addressing mobility of wireless broadband (WiMax). IEEE 802.16e is sometimes called Mobile WiMAX, after the WiMAX forum for interoperability. 802.16e, based on an existing WiMAX standard 802.16a, adds WiMAX mobility in the 2-to-6 GHz-licensed bands. 802.16e allows for fixed wireless and mobile Non Line of Sight (NLOS) applications primarily by enhancing the OFDMA (Orthogonal Frequency Division Multiple Access).IEEE 802.1p A QoS method - A three-bit value that can be placed inside an 802.1Q frame tag. IEEE 802.1q The IEEE 802.1q standard defines the operation of VLAN Bridges that permit the definition, operation and administration of Virtual LAN topologies within a Bridged LAN infrastructure. The 802.1q specification establishes a standard method for inserting VLAN membership information into Ethernet frames. A tag field containing VLAN (and/or 802.1p priority) information can be inserted into an Ethernet frame, carrying VLAN membership information.IEEE 802.3 A Local Area Network protocol suite commonly known as Ethernet. Ethernet uses Carrier Sense Multiple Access bus with Collision Detection CSMA/CD. This method allows users to share the network cable. However, only one station can use the cable at a time. A variety of physical medium dependent protocols are supported.IF Intermediate Frequency. Radio communications systems modulate a carrier frequency with a baseband signal in order to achieve radio transmission. In many cases, the carrier is not modulated directly. Instead, a lower IF signal is modulated and processed. At a later circuit stage, the IF signal is converted up to the transmission frequency band.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-212.png)
![Glossary4Motion 917 System ManualIGMP Internet Group Membership Protocol) is protocol used by IP hosts to report their host group memberships to any immediately neighboring multicast routers.The use of IP multicasting in TCP/IP networks is defined as a TCP/IP standard in RFC 1112. In addition to defining address and host extensions for how IP hosts support multicasting, this RFC also defines the IGMP version 1. Version 2 of IGMP is defined in RFC 2236. Both versions of IGMP provide a protocol to exchange and update information about host membership in specific multicast groups.IP Internet Protocol. The standard that defines how data is transmitted over the Internet. IP bundles data, including e-mail, faxes, voice calls and messages, and other types, into "packets", in order to transmit it over public and private networks.IPv4 Internet Protocol version 4 is still the most commonly used Internet Protocol (IP) version, initially deployed in 1983. IPv4 addresses are 32-bit numbers often expressed as 4 octets in "dotted decimal" notation (for example, 192.0.32.67). IPv6 is the newer version of the Internet Protocol (deployment began in 1999) that offers many improvements over IPv4, such as 128-bit IP addresses, and will eventually completely replace IPv4.ISP Internet Service Provider. A company that provides access to the Internet. KEK Key Encryption Key. Key that encrypts or decrypts other key for transmission or storage.LED Light Emitting Diode.MAC Media Access Control. The lower of the two sub-layers of the data link layer defined by the IEEE. The MAC sub-layer handles access to shared media, such as whether token passing or contention will be used.MAC Address Standardized data link layer address that is required for every port or device that connects to a LAN. Other devices in the network use these addresses to locate specific ports in the network and to create and update routing tables and data structures. MAC addresses are 6bytes long and are controlled by the IEEE. MDT Mechanical Down-TiltMIB Management Information Base. A database of objects that can be monitored by a network management system. SNMP uses standardized MIB formats that allow any SNMP tools to monitor any device defined by a MIB.MIMO Multiple Input, Multiple Output. A technique for faster wireless communication. MIMO allows for the use of multiple transmitter and receiver antennas to increase throughput and range.MIP Mobile IP. A protocol used to provide IP mobility to IPv4-based nodes, defined in RFC-2002.MIR Maximum Information Rate. Specifies the maximum rate of information that can be available to a user. The MIR is used by the traffic policing mechanism to prevent users from sending excess traffic to the network.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-213.png)
![Glossary4Motion 918 System ManualMTU Maximum Transmission Unit. This is the greatest amount of data that can be transferred in one physical frame on the network. If a packet that has a smaller MTU than the packet's frame length is sent, fragmentation will occur. For TCP MTU can range from 68 to 1500 bytes. Larger MTUs provide for lower overhead (fewer headers).MS Mobile Station. The equipment used by the end user to access the WiMAX network.NAI Network Address Identifier. Used to create a new unique subscriber identifier, when a subscriber enters the network without a user name. NAP Network Access Provider. A NAP is a business entity that provides WiMAX radio access infrastructure to one or more Network Service Providers (NSPs). An NAP implements this infrastructure using one or more ASNs.NAS Network Access Server. A Network Access Server operates as a client of RADIUS. The client is responsible for passing user information to designated RADIUS server(s(, and then acting on the response.NMS Network Management System. A system responsible for managing at least part of a network. An NMS is generally a reasonably powerful and well-equipped computer, such as an engineering workstation. NMSs communicate with agents to help keep track of network statistics and resources.NOC Network Operations Center. The physical space from which a typically large telecommunications network is managed, monitored and supervised.NPU Network Processing UnitNRT-VR Non Real Time - Variable Rate. Service supporting non-real-time applications with variable bit rates that require guaranteed data rate and are delay-tolerant such as file transfersNSP Network Service Provider. An NSP is a business entity that provides IP connectivity and WiMAX services to WiMAX subscribers compliant with the established service level agreement. The NSP concept is an extension of the Internet service provider (ISP) concept, providing network services beyond Internet access. To provide these services, an NSP establishes contractual agreements with one or more NAPs. An NSP may also establish roaming agreements with other NSPs and contractual agreements with third-party application providers (e.g. ASP, ISP) for the delivery of WiMAX services to subscribers. From a WiMAX subscriber standpoint, an NSP may be classified as a home or visited NSP.NWG Network Working Group. The WiMAX Forum's Network Working Group (NWG) is responsible for developing the end-to-end network requirements, architecture, and protocols for WiMAX, using IEEE 802.16e-2005 as the air interface.OA&M Operation, Administration & Maintenance. Provides the facilities and the personnel required to manage a network. OCXO Oven-Controlled crystal oscillator often used in navigation system clocks, frequency standards, MTI radars, wireless base stations, telecom timing modules and precision test equipment.ODU Outdoor Unit](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-214.png)
![Glossary4Motion 919 System ManualOFDM Orthogonal Frequency Division Multiplexing: A method for multiplexing signals, which divides the available bandwidth into a series of frequencies known as tones. Orthogonal tones do not interfere with each other when the peak of one tone corresponds with the null. The rapid switching, frequency-hopping technique is intended to allow more robust data service.OFDMA Orthogonal Frequency Division Multiple Access. It’s a logical extension of OFDM and a modulation/multiple access technique. OFDMA divides a signal into sub-channels (i.e. groups of carriers), with each sub-channel (or several sub-channels) being allocated to a different subscriber. OOB Out-Of-Band. Out-of-band management is a method wherein management information exchanged between the network element and its associated management application is carried on a separate communications path from the user data that is coming to/from the network element. Conversely, in-band (IB) management is management data that is carried across the same interface as user data.OSPF Open Shortest Path First. A link-state IGP (Interior gateway protocol) that makes routing decisions based on the shortest-path-first (SPF) algorithm (also referred to as the Dijkstra algorithm).OSS Operations Support Systems. A system that processes telecommunications information supporting various management functions, such as billing, customer care, network management, inventory control, maintenance, trouble ticket reporting, surveillance and service provisioning; not considered a network element or part of the network itself.PDA Personal Digital Assistant. A handheld computing device.PDU Protocol Data Unit. The concept of a PDU is used in the OSI reference model. From the perspective of a protocol layer, a PDU consists of information from the layer above plus the protocol information appended to the data by that layer.. For example, a frame is a PDU of the Data Link Layer, and a packet is a PDU of the Network Layer. PEP Policy Enforcement Point is an entity in a policy-based system where decisions are enacted.PER Packet Error Rate. In a digital transmission, PER is the percentage of packets with errors divided by the total number of packets that have been transmitted, received or processed over a given time period.PHS Payload Header Suppression. PHS is a technique used to mask redundant cell, frame, or packet header information when one or more of the same type of higher layer data PDUs are transported as the payload of an 802.16 MAC PDU. PHY PHYsical Layer. The physical, or lowest, layer of the OSI Network Model. In a wireless network, the PHY defines parameters such as data rates, modulation method, signaling parameters, transmitter/receiver synchronization, etc. Within an actual radio implementation, the PHY corresponds to the radio front end and baseband signal processing sections.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-215.png)
![Glossary4Motion 920 System ManualPICMG The PCI Industrial Computers Manufacturer's Group is a consortium of over 450 industrial computer product vendors. PICMG's charter is to develop specifications for PCI-based systems and boards for use in industrial computing applications. PICMG 2.x series is a specification for PCI-based equipment that combines the power of low cost PCI silicon and software with the rugged Eurocard packaging.PIM Protocol Independent Multicast. A protocol-independent multicast routing protocol. PIM sparse mode routes to multicast groups that might span wide-area and interdomain internets. PIM dense mode is a flood-and-prune protocol.PIU Power Interface UnitPKM Privacy Key Management. The key management protocol used in 802.16 to obtain the needed authorization to use the media. PKM protocol operates in two phases: AK (Authorization Key) phase, and TEK (Traffic Encryption Keys). AK represents the secret key used to obtain TEK in the exchanges between MS and BS in subsequent phases.PSU Power Supply UnitPUSC Partial Usage of Sub-ChannelsQAM Quadrature Amplitude Modulation. A technique used in wireless applications to double the available bandwidth by combining two amplitude-modulated signals. The two combined signals differ in phase by 90 degrees; this technique doubles the bandwidth by combining the two signals at the source before transmission, transmitting digital data at a rate of 4 bits per signal change. QoS Quality of Service. Measure of performance for a transmission system that reflects its transmission quality and service availability.QPSK Quadrature Phase Shift Keying. A data transfer technique used in coaxial cable networks that sends data using modulating signals. Four different phases represent data, with each signal's information determined by the signal before it. For example, if a phase stays the same from one signal to the other, the information has not changed.RADIUS Remote Authentication Dial-In User Service, an authentication and accounting system used by many Internet Service Providers (ISPs). When you connect to the system you must enter your username and password. This information is passed to a RADIUS server, which checks that the information is correct, and then authorizes access to the system.RET Remote Electrical TiltRF Radio frequency. An AC signal of high enough frequency to be used for wireless communications. RFC Request For Comments. The name of the result and the process for creating a standard on the Internet. New standards are proposed and published on the Internet, as a Request For Comments. The proposal is reviewed by the Internet Engineering Task Force.RoHS Restriction of the use of certain Hazardous Substances in electrical and electronic equipment, reference EC Directive 2002/95/EC of 27 January 2003.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-216.png)
![Glossary4Motion 921 System ManualRS-232 A serial interface published by the EIA (Electronic Industries Association) for asynchronous data communication over distances up to a few hundred feet. Characterized by a single-ended (not differential) physical layer, it uses one signal wire for transmission, another for reception, and a common wire (ground), plus some timing and control signals.RS-422 RS-422 is a serial interface standard in which data is sent in a differential pair (two wires, or twisted pair cable), which allows greater distances and higher data rates than non-differential serial schemes such as RS-232. RSSI Received Signal Strength Indicator. A signal or circuit that indicates the strength of the incoming (received) signal in a receiver.R&TTE Radio & Telecommunications Terminal Equipment. The R&TTE Directive 1999/5/EC governs the marketing and use of R&TTE equipment. With the exception of a few categories of equipment, the Directive covers all equipment, which uses the radio frequency spectrum. It also covers all terminal equipment attached to public telecommunication networks.RTC Real Time Clock.RTD Round Trip Delay.RTP Real Time Protocol. An Internet protocol for transmitting real-time data such as audio and video. RTP itself does not guarantee real-time delivery of data, but it does provide mechanisms for the sending and receiving applications to support streaming data. Typically, RTP runs on top of the UDP protocol, although the specification is general enough to support other transport protocols.RT-VR Real Time - Variable Rate. Service supporting real-time applications with variable bit rates that require guaranteed data rate and delay such as streaming video.Rx ReceiveSBS Serving Base StationSDU Service Data Unit. A set of data that is sent by a user of services of a given layer, and is transmitted to a peer service user semantically unchanged. The SDU is the data that a certain layer will pass to the layer below.SFA Service Flow Authorization. SFM The Service Flow Manager (SFM) located in the BS is responsible for the creation, admission, activation, modification, and deletion of IEEE 802.16e-2005 service flows. It consists of an Admission Control (AC) function, data path function and the associated local resource information. AC decides whether a new service flow can be admitted to the system.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-217.png)
![Glossary4Motion 922 System ManualSNMP Simple Network Management Protocol. A network management protocol that provides a means to monitor and control network devices, and to manage configurations, statistics collection, performance, and security. SNMP works by sending messages, called protocol data units (PDUs), to different parts of a network. SNMP-compliant devices, called agents, store data about themselves in Management Information Bases (MIBs) and return this data to the SNMP requesters.SSH Secure Shell is a protocol for secure remote login and other secure network services over an insecure network.TBS Target Base StationTCP Transmission Control Protocol. Connection-oriented transport layer protocol that provides reliable full-duplex data transmission. TCP is the part of the TCP/IP suite of protocols that is responsible for forming data connections between nodes that are reliable, as opposed to IP, which is connectionless and unreliable. TCXO Temperature-Compensated crystal oscillator often used for frequency control in tactical radios, telecom timing modules (Stratum 3 Type), wireless systems, and reference oscillators.TDD Time Division Duplex is a duplexing technique dividing a radio channel in time to allow downlink operation during part of the frame period and uplink operation in the remainder of the frame period.TEK Traffic Encryption Key - a symmetric key that is used to encrypt/decrypt messages.TFTP Trivial File Transfer Protocol. Simplified version of FTP that allows files to be transferred from one computer to another over a network, usually without the use of client authentication.ToS Type of service. The method of handling traffic using information extracted from the fields in the ToS byte to differentiate packet flows.Tx TransmitTUV TÜV is a safety-testing laboratory with headquarters in Germany. TÜV can test products for compliance with IEC or VDE requirements. Products that have the TÜV insignia have been tested by TÜV for compliance with applicable standards for sale in the European market.UAbbreviation for "Unit" or standard height measurement which defines the vertical height for plug-in modules in the 19” construction system. One U equals 44.5 mm.UCD Uplink Channel Descriptor.UDP User Datagram Protocol. Connectionless transport layer protocol in the TCP/IP protocol stack. UDP is a simple protocol that exchanges datagrams without acknowledgments or guaranteed delivery, requiring that error processing and retransmission be handled by other protocols. UDP is defined in RFC 768. UGS Unsolicited Grant Service. Service supporting real-time applications generating fixed-rate data such as voice over IP without silence suppression.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-218.png)
![Glossary4Motion 923 System ManualUL 1. Abbreviation for “Underwriters’ Laboratory”. The UL is an independent organization which conducts safety tests and product certifications.2. Up LinkUTC Coordinated Universal Time. The reference for the official time used by all countries in the world, maintained by an ensemble of atomic clocks around the world, and it is independent from the time zones. The modern implementation of Greenwich Mean Time. VLAN Virtual Local Area Network. A group of devices on one or more LANs that are configured with the same VLAN ID so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Used also to create separation between different user groups.VoIP Voice over Internet Protocol. Provides an advanced digital communications network that bypasses the traditional public switched telephone system and uses the Internet to transmit voice communication. VoIP enables people to use the Internet as the transmission medium for telephone calls by sending voice data in packets using IP rather than by traditional circuit switched transmissions of the PSTN.WCS Wireless Communications Service is defined by the Federal Communications Commission as radio communications that may provide fixed, mobile, radio location, or satellite communication services to individuals and businesses within their assigned spectrum block and geographical area. The WCS is in the 2.3 GHz band from 2,305 to 2,320 MHz and 2,345 to 2,360 MHz.WEEE Waste Electronic and Electrical Equipment. The purpose of Directive 2002/96/EC on waste electrical and electronic equipment (WEEE) is, as a first priority, the prevention of waste electrical and electronic equipment (WEEE), and in addition, the reuse, recycling and other forms of recovery of such wastes so as to reduce the disposal of waste. It also seeks to improve the environmental performance of all operators involved in the life cycle of electrical and electronic equipment, e.g. producers, distributors and consumers and in particular those operators directly involved in the treatment of waste electrical and electronic equipment.Wi-Fi Wi-Fi (short for wireless fidelity and pronounced 'why-fye') is a term for certain types of wireless local area network that use specifications in the IEEE 802.11 family. The term Wi-Fi was created by an organization called the Wi-Fi Alliance, which oversees tests that certify product interoperability.WiMAX WiMAX is an acronym that stands for Worldwide Interoperability for Microwave Access. WiMAX is a standards-based technology enabling the delivery of last mile wireless broadband access as an alternative to cable and DSL. WiMAX provides fixed, nomadic, portable, and mobile wireless broadband connectivity without the need for direct line-of-sight to a base station.XML Extensible Markup Language. Language used for defining a set of markers, called tags, that define the function and hierarchical relationships of the parts of a document or data set. It is a flexible way to create common information formats and share both the format and the data, most commonly on the web. It generally similar to HTML and helps share information in a consistent way. XML is "extensible" because, unlike HTML, the markup symbols are unlimited and self-defining.](https://usermanual.wiki/Alvarion-Technologies/MICRO-25.Manual-p5/User-Guide-1329246-Page-219.png)